void LED_Init(void)
{
unsigned char i;
LEDPIN_Init();
// LED_PORT=0X0F;
//LED_SCLH;;;
//LED_RSTL;;;
digitalWrite(SCL_PIN,HIGH);;;
digitalWrite(RST_PIN,LOW);;;
// for(i=0;i<100;i++)asm("nop");
LED_DLY_ms(50);
//LED_RSTH;;;
digitalWrite(RST_PIN,HIGH);
Set_Display_On_Off(0x00); // Display Off (0x00/0x01)
Set_Display_Clock(0x80); // Set Clock as 100 Frames/Sec
Set_Multiplex_Ratio(0x3F); // 1/64 Duty (0x0F~0x3F)
Set_Display_Offset(0x00); // Shift Mapping RAM Counter (0x00~0x3F)
SetStartLine(0x00); // Set Mapping RAM Display Start Line (0x00~0x3F)
Set_Charge_Pump(0x04); // Enable Embedded DC/DC Converter (0x00/0x04)
SetAddressingMode(0x02); // Set Page Addressing Mode (0x00/0x01/0x02)
Set_Segment_Remap(0x01); // Set SEG/Column Mapping
Set_Common_Remap(0x08); // Set COM/Row Scan Direction
Set_Common_Config(0x10); // Set Sequential Configuration (0x00/0x10)
SetContrastControl(0xCF); // Set SEG Output Current
Set_Precharge_Period(0xF1); // Set Pre-Charge as 15 Clocks & Discharge as 1 Clock
Set_VCOMH(0x40); // Set VCOM Deselect Level
Set_Entire_Display(0x00); // Disable Entire Display On (0x00/0x01)
Set_Inverse_Display(0x00); // Disable Inverse Display On (0x00/0x01)
Set_Display_On_Off(0x01); // Display On (0x00/0x01)
LED_Fill(0x00); //clear all
LED_Set_Pos(0,0);
}
void LED_Init(void) {
LEDPIN_Init();
/*while(1)
{
//MB_Sleep(1000);
LED_WrCmd(0xaa);
//MB_Sleep(1000);
XGpio_DiscreteWrite(&led2, reset_CHANNEL, 0x1);
XGpio_DiscreteWrite(&led1, reset_CHANNEL, 0x0);
}*/
XGpio_DiscreteWrite(&reset, reset_CHANNEL, 0x0);
//usleep(800);
MB_Sleep(80);
XGpio_DiscreteWrite(&reset, reset_CHANNEL, 0x1);
Set_Display_On_Off(0x00); // Display Off (0x00/0x01)
Set_Display_Clock(0x80); // Set Clock as 100 Frames/Sec
Set_Multiplex_Ratio(0x3F); // 1/64 Duty (0x0F~0x3F)
Set_Display_Offset(0x00); // Shift Mapping RAM Counter (0x00~0x3F)
SetStartLine(0x00); // Set Mapping RAM Display Start Line (0x00~0x3F)
Set_Charge_Pump(0x04); // Enable Embedded DC/DC Converter (0x00/0x04)
SetAddressingMode(0x02); // Set Page Addressing Mode (0x00/0x01/0x02)
Set_Segment_Remap(0x01); // Set SEG/Column Mapping 0x00左右反置 0x01正常
Set_Common_Remap(0x08); // Set COM/Row Scan Direction 0x00上下反置 0x08正常
Set_Common_Config(0x10); // Set Sequential Configuration (0x00/0x10)
SetContrastControl(0xCF); // Set SEG Output Current
Set_Precharge_Period(0xF1); // Set Pre-Charge as 15 Clocks & Discharge as 1 Clock
Set_VCOMH(0x40); // Set VCOM Deselect Level
Set_Entire_Display(0x00); // Disable Entire Display On (0x00/0x01)
Set_Inverse_Display(0x00); // Disable Inverse Display On (0x00/0x01)
Set_Display_On_Off(0x01); // Display On (0x00/0x01)
LED_Fill(0x00); //初始清屏
LED_Set_Pos(0, 0);
}
void setup()
{
LEDPIN_Init();
LED_Init();
}
