void LLWU_Init(void){
printf("[LLWU_Init] LLWU initialize routine \n\n");
//enable wakeup pin enable NMI - PTA4 - WUPE3
LLWU_PE1 |= (LLWU_PE1_WUPE3(2)| LLWU_PE1_WUPE2(2)| LLWU_PE1_WUPE1(2) |LLWU_PE1_WUPE0(2));
LLWU_PE2 |= (LLWU_PE2_WUPE7(2)| LLWU_PE2_WUPE6(2)| LLWU_PE2_WUPE5(2) |LLWU_PE2_WUPE4(2));
LLWU_PE3 |= (LLWU_PE3_WUPE11(2)| LLWU_PE3_WUPE10(2)| LLWU_PE3_WUPE9(2) |LLWU_PE3_WUPE8(2));
LLWU_PE4 |= (LLWU_PE4_WUPE15(2)| LLWU_PE4_WUPE14(2)| LLWU_PE4_WUPE13(2) |LLWU_PE4_WUPE12(2));
printf("[LLWU_Init] modules 3,2,1,0 enabled; LLWU PE1 = %#02X \r\n", (LLWU_PE1) );
printf("[LLWU_Init] modules 7,6,5,4 enabled; LLWU PE2 = %#02X \r\n", (LLWU_PE2) );
printf("[LLWU_Init] modules 11,10,9,8 enabled; LLWU PE3 = %#02X \r\n", (LLWU_PE3) );
printf("[LLWU_Init] modules 15,14,13,12 enabled; LLWU PE4 = %#02X \r\n", (LLWU_PE4) );
//falling edge on all pins
LLWU_CS = 0x07; //enable reset filter
printf("[LLWU_Init]enable reset filter enabled; LLWU_CS = %#02X \r\n", (LLWU_CS) );
//LLWU_M5IF
// enable all modules to wakeup from low power modes
LLWU_ME |= (LLWU_ME_WUME7_MASK |LLWU_ME_WUME6_MASK |LLWU_ME_WUME5_MASK \
|LLWU_ME_WUME4_MASK |LLWU_ME_WUME3_MASK |LLWU_ME_WUME2_MASK \
|LLWU_ME_WUME1_MASK | LLWU_ME_WUME0_MASK);
printf("[LLWU_Init]All modules enabled; LLWU ME = %#02X \r\n", (LLWU_ME) );
NVICISER0 = NVIC_ISER_SETENA_MASK; //enable llwu interrupts in the NVIC
}
void llwu_configure(unsigned int pin_en, unsigned char rise_fall, unsigned char module_en ) {
uint8 temp;
temp = LLWU_PE1;
if( pin_en & 0x0001)
{
LLWU_Info("\n\r Invalid LLWU configured pin PTE1/SCI1_RX/I2C1_SCL /SPI1_SIN");
}
if( pin_en & 0x0002)
{
LLWU_Info("\n\r Invalid LLWU configured pin PTE2/SPI1_SCK/SDHC0_DCLK");
}
if( pin_en & 0x0004)
{
LLWU_Info("\n\r Invalid LLWU configured pin PTE4/SPI1_PCS0/SDHC0_D3");
}
if( pin_en & 0x0008)
{
LLWU_Info("\n\r Invalid LLWU configured pin PTA4/FTM0_CH1/NMI/EZP_CS");
}
LLWU_PE1 = temp;
temp = LLWU_PE2;
if( pin_en & 0x0010)
{
LLWU_Info("\n\r Invalid LLWU configured pin PTA13/FTM1_CH1 /FTM1_QD_PHB");
}
if( pin_en & 0x0020)
{
temp |= LLWU_PE2_WUPE5(rise_fall);
LLWU_Info("\n\r LLWU configured pins PTB0/I2C0_SCL/FTM1_CH0/FTM1_QD_PHA is LLWU wakeup source ");
LLWU_F1 |= LLWU_F1_WUF5_MASK; // write one to clear the flag
}
if( pin_en & 0x0040)
{
temp |= LLWU_PE2_WUPE6(rise_fall);
LLWU_Info("\n\r LLWU configured pins PTC1/SCI1_RTS/FTM0_CH0 is LLWU wakeup source ");
LLWU_F1 |= LLWU_F1_WUF6_MASK; // write one to clear the flag
}
if( pin_en & 0x0080)
{
temp |= LLWU_PE2_WUPE7(rise_fall);
LLWU_Info("\n\r LLWU configured pins PTC3/SCI1_RX/FTM0_CH2 is LLWU wakeup source ");
LLWU_F1 |= LLWU_F1_WUF7_MASK; // write one to clear the flag
}
LLWU_PE2 = temp;
temp = LLWU_PE3;
if( pin_en & 0x0100)
{
temp |= LLWU_PE3_WUPE8(rise_fall);
LLWU_Info("\n\r LLWU configured pins PTC4/SPI0_PCS0/FTM0_CH3 is LLWU wakeup source ");
LLWU_F2 |= LLWU_F2_WUF8_MASK; // write one to clear the flag
}
if( pin_en & 0x0200)
{
temp |= LLWU_PE3_WUPE9(rise_fall);
LLWU_Info("\n\r LLWU configured pins PTC5/SPI0_SCK/I2S0_RXD0 is LLWU wakeup source ");
LLWU_F2 |= LLWU_F2_WUF9_MASK; // write one to clear the flag
}
if( pin_en & 0x0400)
{
temp |= LLWU_PE3_WUPE10(rise_fall);
LLWU_Info("\n\r LLWU configured pins PTC6/PDB0_EXTRG to be an LLWU wakeup source ");
LLWU_F2 |= LLWU_F2_WUF10_MASK; // write one to clear the flag
}
if( pin_en & 0x0800)
{
temp |= LLWU_PE3_WUPE11(rise_fall);
LLWU_Info("\n\r LLWU configured pins PTC11/I2S0_RXD1 to be an LLWU wakeup source ");
LLWU_F2 |= LLWU_F2_WUF11_MASK; // write one to clear the flag
}
LLWU_PE3 = temp;
temp = LLWU_PE4;
if( pin_en & 0x1000)
{
temp |= LLWU_PE4_WUPE12(rise_fall);
LLWU_Info("\n\r LLWU configured pins PTD0/SPI0_PCS0/SCI2_RTS to be an LLWU wakeup source ");
LLWU_F2 |= LLWU_F2_WUF12_MASK; // write one to clear the flag
}
if( pin_en & 0x2000)
{
temp |= LLWU_PE4_WUPE13(rise_fall);
LLWU_Info("\n\r LLWU configured pins PTD2/SCI2_RX to be an LLWU wakeup source ");
LLWU_F2 |= LLWU_F2_WUF13_MASK; // write one to clear the flag
}
if( pin_en & 0x4000)
{
temp |= LLWU_PE4_WUPE14(rise_fall);
LLWU_Info("\n\r LLWU configured pins PTD4/SCI0_RTS/FTM0_CH4/EWM_IN is LLWU wakeup source ");
LLWU_F2 |= LLWU_F2_WUF14_MASK; // write one to clear the flag
}
if( pin_en & 0x8000)
{
temp |= LLWU_PE4_WUPE15(rise_fall);
LLWU_Info("\n\r LLWU configured pins PTD6/SCI0_RX/FTM0_CH6/FTM0_FLT0 is LLWU wakeup source ");
LLWU_F2 |= LLWU_F2_WUF15_MASK; // write one to clear the flag
}
LLWU_PE4 = temp;
if (module_en == 0){
LLWU_ME = 0;
}else {
LLWU_ME |= module_en; //Set up more modules to wakeup up
LLWU_Info("\n\r LLWU configured modules as LLWU wakeup sources = 0x%02X,",(LLWU_ME));
}
} // End LLWU Configuration
/*******************************************************************************
*
* llwu_configure -
*
* description: Set up the LLWU for wakeup of the MCU from LLS and VLLSx modes
* from the selected pin or module.
*
* inputs: pin_en - indicates the wakeup pin is enabled.
* rise_fall - 0x00 = External input disabled as wakeup
* 0x01 - External input enabled as rising edge detection
* 0x02 - External input enabled as falling edge detection
* 0x03 - External input enabled as any edge detection
* module_en - indicates the wakeup module is enabled.
*******************************************************************************/
void llwu_configure(uint32_t pin_en, uint8_t rise_fall, uint32_t module_en ) {
llwu_clear_flags();
if (pin_en != 0) {
//------------------------------------------------
LLWU_PE1 = 0;
if (pin_en & LLWU_PIN_26) {
LLWU_PE1 |= LLWU_PE1_WUPE0(rise_fall);
}
if (pin_en & LLWU_PIN_33) {
LLWU_PE1 |= LLWU_PE1_WUPE3(rise_fall);
}
//------------------------------------------------
LLWU_PE2 = 0;
if( pin_en & LLWU_PIN_4) {
LLWU_PE2 |= LLWU_PE2_WUPE4(rise_fall);
}
if( pin_en & LLWU_PIN_16) { //TSI enabled
LLWU_PE2 |= LLWU_PE2_WUPE5(rise_fall);
}
if( pin_en & LLWU_PIN_22) {// TSI ensbled
LLWU_PE2 |= LLWU_PE2_WUPE6(rise_fall);
}
if( pin_en & LLWU_PIN_9) {
LLWU_PE2 |= LLWU_PE2_WUPE7(rise_fall);
}
//------------------------------------------------
LLWU_PE3 = 0;
if( pin_en & LLWU_PIN_10) {
LLWU_PE3 |= LLWU_PE3_WUPE8(rise_fall);
}
if( pin_en & LLWU_PIN_13) {
LLWU_PE3 |= LLWU_PE3_WUPE9(rise_fall);
}
if( pin_en & LLWU_PIN_11) {
LLWU_PE3 |= LLWU_PE3_WUPE10(rise_fall);
}
if( pin_en & LLWU_PIN_30) {
LLWU_PE3 |= LLWU_PE3_WUPE11(rise_fall);
}
//------------------------------------------------
LLWU_PE4 = 0;
if( pin_en & LLWU_PIN_2) {
LLWU_PE4 |= LLWU_PE4_WUPE12(rise_fall);
}
if( pin_en & LLWU_PIN_7) {
LLWU_PE4 |= LLWU_PE4_WUPE13(rise_fall);
}
if( pin_en & LLWU_PIN_6) {
LLWU_PE4 |= LLWU_PE4_WUPE14(rise_fall);
}
if( pin_en & LLWU_PIN_21) {
LLWU_PE4 |= LLWU_PE4_WUPE15(rise_fall);
}
}
if (module_en != 0) {
//------------------------------------------------
LLWU_ME = 0;
if( module_en & LLWU_LPTMR_MOD) {
BITBAND_U8(LLWU_ME, WUME0_BIT) = 1;
//LLWU_ME |= LLWU_ME_WUME0_MASK;
}
if( module_en & LLWU_CMP0_MOD) {
BITBAND_U8(LLWU_ME, WUME1_BIT) = 1;
//LLWU_ME |= LLWU_ME_WUME1_MASK;
}
if( module_en & LLWU_CMP1_MOD) {
BITBAND_U8(LLWU_ME, WUME2_BIT) = 1;
//LLWU_ME |= LLWU_ME_WUME2_MASK;
}
if( module_en & LLWU_TSI_MOD) {
BITBAND_U8(LLWU_ME, WUME4_BIT) = 1;
//LLWU_ME |= LLWU_ME_WUME4_MASK;
}
if( module_en & LLWU_RTCA_MOD) {
BITBAND_U8(LLWU_ME, WUME5_BIT) = 1;
//LLWU_ME |= LLWU_ME_WUME5_MASK;
}
if( module_en & LLWU_RTCS_MOD) {
BITBAND_U8(LLWU_ME, WUME7_BIT) = 1;
//LLWU_ME |= LLWU_ME_WUME7_MASK;
}
return;
}
}
/* function: llwu_configure
description: Set up the LLWU for wakeup the MCU from LLS and VLLSx modes
from the selected pin or module.
inputs:
pin_en - unsigned integer, bit position indicates the pin is enabled.
More than one bit can be set to enable more than one pin at a time.
rise_fall - 0x00 = External input disabled as wakeup
0x01 - External input enabled as rising edge detection
0x02 - External input enabled as falling edge detection
0x03 - External input enablge as any edge detection
module_en - unsigned char, bit position indicates the module is enabled.
More than one bit can be set to enabled more than one module
for example: if bit 0 and 1 need to be enabled as rising edge detect call this routine with
pin_en = 0x0003 and rise_fall = 0x02
Note: to set up one set of pins for rising and another for falling, 2 calls to this
function are required, 1st for rising then the second for falling.
*/
void llwu_configure(unsigned int pin_en, unsigned char rise_fall, unsigned char module_en )
{
uint8_t temp;
temp = LLWU_PE1;
if( pin_en & 0x0001)
{
temp |= LLWU_PE1_WUPE0(rise_fall);
// LLWU configured pins PTE1/UART1_RX/I2C1_SCL /SPI1_SIN to be an LLWU wakeup source
LLWU_F1 |= LLWU_F1_WUF0_MASK; // write one to clear the flag
}
if( pin_en & 0x0002)
{
temp |= LLWU_PE1_WUPE1(rise_fall);
// LLWU configured pins PTE2/SPI1_SCK/SDHC0_DCLK to be an LLWU wakeup source
LLWU_F1 |= LLWU_F1_WUF1_MASK; // write one to clear the flag
}
if( pin_en & 0x0004)
{
temp |= LLWU_PE1_WUPE2(rise_fall);
// LLWU configured pins PTE4/SPI1_PCS0/SDHC0_D3 to be an LLWU wakeup source
LLWU_F1 |= LLWU_F1_WUF2_MASK; // write one to clear the flag
}
if( pin_en & 0x0008)
{
temp |= LLWU_PE1_WUPE3(rise_fall);
// LLWU configured pins PTA4/FTM0_CH1/NMI/EZP_CS to be an LLWU wakeup source
LLWU_F1 |= LLWU_F1_WUF3_MASK; // write one to clear the flag
}
LLWU_PE1 = temp;
temp = LLWU_PE2;
if( pin_en & 0x0010)
{
temp |= LLWU_PE2_WUPE4(rise_fall);
// LLWU configured pins PTA13/FTM1_CH1 /FTM1_QD_PHB to be an LLWU wakeup source
LLWU_F1 |= LLWU_F1_WUF4_MASK; // write one to clear the flag
}
if( pin_en & 0x0020)
{
temp |= LLWU_PE2_WUPE5(rise_fall);
// LLWU configured pins PTB0/I2C0_SCL/FTM1_CH0/FTM1_QD_PHA to be an LLWU wakeup source
LLWU_F1 |= LLWU_F1_WUF5_MASK; // write one to clear the flag
}
if( pin_en & 0x0040)
{
temp |= LLWU_PE2_WUPE6(rise_fall);
// LLWU configured pins PTC1/UART1_RTS/FTM0_CH0 to be an LLWU wakeup source
LLWU_F1 |= LLWU_F1_WUF6_MASK; // write one to clear the flag
}
if( pin_en & 0x0080)
{
temp |= LLWU_PE2_WUPE7(rise_fall);
// LLWU configured pins PTC3/UART1_RX/FTM0_CH2 to be an LLWU wakeup source
LLWU_F1 |= LLWU_F1_WUF7_MASK; // write one to clear the flag
}
LLWU_PE2 = temp;
temp = LLWU_PE3;
if( pin_en & 0x0100)
{
temp |= LLWU_PE3_WUPE8(rise_fall);
// LLWU configured pins PTC4/SPI0_PCS0/FTM0_CH3 to be an LLWU wakeup source
LLWU_F2 |= LLWU_F2_WUF8_MASK; // write one to clear the flag
}
if( pin_en & 0x0200)
{
temp |= LLWU_PE3_WUPE9(rise_fall);
// LLWU configured pins PTC5/SPI0_SCK/I2S0_RXD0 to be an LLWU wakeup source
LLWU_F2 |= LLWU_F2_WUF9_MASK; // write one to clear the flag
}
if( pin_en & 0x0400)
{
temp |= LLWU_PE3_WUPE10(rise_fall);
// LLWU configured pins PTC6/PDB0_EXTRG to be an LLWU wakeup source
LLWU_F2 |= LLWU_F2_WUF10_MASK; // write one to clear the flag
}
if( pin_en & 0x0800)
{
temp |= LLWU_PE3_WUPE11(rise_fall);
// LLWU configured pins PTC11/I2S0_RXD1 to be an LLWU wakeup source
LLWU_F2 |= LLWU_F2_WUF11_MASK; // write one to clear the flag
}
LLWU_PE3 = temp;
temp = LLWU_PE4;
if( pin_en & 0x1000)
{
temp |= LLWU_PE4_WUPE12(rise_fall);
// LLWU configured pins PTD0/SPI0_PCS0/UART2_RTS to be an LLWU wakeup source
LLWU_F2 |= LLWU_F2_WUF12_MASK; // write one to clear the flag
}
if( pin_en & 0x2000)
{
temp |= LLWU_PE4_WUPE13(rise_fall);
// LLWU configured pins PTD2/UART2_RX to be an LLWU wakeup source
LLWU_F2 |= LLWU_F2_WUF13_MASK; // write one to clear the flag
}
if( pin_en & 0x4000)
{
temp |= LLWU_PE4_WUPE14(rise_fall);
// LLWU configured pins PTD4/UART0_RTS/FTM0_CH4/EWM_IN to be an LLWU wakeup source
LLWU_F2 |= LLWU_F2_WUF14_MASK; // write one to clear the flag
}
if( pin_en & 0x8000)
{
temp |= LLWU_PE4_WUPE15(rise_fall);
// LLWU configured pins PTD6/UART0_RX/FTM0_CH6/FTM0_FLT0 to be an LLWU wakeup source
LLWU_F2 |= LLWU_F2_WUF15_MASK; // write one to clear the flag
}
LLWU_PE4 = temp;
LLWU_ME = module_en; //Set up modules to wakeup up
}