int lbs_rtap_supported(struct lbs_private *priv)
{
if (MRVL_FW_MAJOR_REV(priv->fwrelease) == MRVL_FW_V5)
return 1;
/* newer firmware use a capability mask */
return ((MRVL_FW_MAJOR_REV(priv->fwrelease) >= MRVL_FW_V10) &&
(priv->fwcapinfo & MESH_CAPINFO_ENABLE_MASK));
}
/*
* Check mesh FW version and appropriately send the mesh start
* command
*/
int lbs_init_mesh(struct lbs_private *priv)
{
int ret = 0;
lbs_deb_enter(LBS_DEB_MESH);
/* Determine mesh_fw_ver from fwrelease and fwcapinfo */
/* 5.0.16p0 9.0.0.p0 is known to NOT support any mesh */
/* 5.110.22 have mesh command with 0xa3 command id */
/* 10.0.0.p0 FW brings in mesh config command with different id */
/* Check FW version MSB and initialize mesh_fw_ver */
if (MRVL_FW_MAJOR_REV(priv->fwrelease) == MRVL_FW_V5) {
/* Enable mesh, if supported, and work out which TLV it uses.
0x100 + 291 is an unofficial value used in 5.110.20.pXX
0x100 + 37 is the official value used in 5.110.21.pXX
but we check them in that order because 20.pXX doesn't
give an error -- it just silently fails. */
/* 5.110.20.pXX firmware will fail the command if the channel
doesn't match the existing channel. But only if the TLV
is correct. If the channel is wrong, _BOTH_ versions will
give an error to 0x100+291, and allow 0x100+37 to succeed.
It's just that 5.110.20.pXX will not have done anything
useful */
priv->mesh_tlv = TLV_TYPE_OLD_MESH_ID;
if (lbs_mesh_config(priv, CMD_ACT_MESH_CONFIG_START, 1)) {
priv->mesh_tlv = TLV_TYPE_MESH_ID;
if (lbs_mesh_config(priv, CMD_ACT_MESH_CONFIG_START, 1))
priv->mesh_tlv = 0;
}
} else
if ((MRVL_FW_MAJOR_REV(priv->fwrelease) >= MRVL_FW_V10) &&
(priv->fwcapinfo & MESH_CAPINFO_ENABLE_MASK)) {
/* 10.0.0.pXX new firmwares should succeed with TLV
* 0x100+37; Do not invoke command with old TLV.
*/
priv->mesh_tlv = TLV_TYPE_MESH_ID;
if (lbs_mesh_config(priv, CMD_ACT_MESH_CONFIG_START, 1))
priv->mesh_tlv = 0;
}
/* Stop meshing until interface is brought up */
lbs_mesh_config(priv, CMD_ACT_MESH_CONFIG_STOP, 1);
if (priv->mesh_tlv) {
sprintf(priv->mesh_ssid, "mesh");
priv->mesh_ssid_len = 4;
ret = 1;
}
lbs_deb_leave_args(LBS_DEB_MESH, "ret %d", ret);
return ret;
}
int lbs_init_mesh(struct lbs_private *priv)
{
int ret = 0;
lbs_deb_enter(LBS_DEB_MESH);
/* */
/* */
/* */
/* */
/* */
if (MRVL_FW_MAJOR_REV(priv->fwrelease) == MRVL_FW_V5) {
/*
*/
/*
*/
priv->mesh_tlv = TLV_TYPE_OLD_MESH_ID;
if (lbs_mesh_config(priv, CMD_ACT_MESH_CONFIG_START, 1)) {
priv->mesh_tlv = TLV_TYPE_MESH_ID;
if (lbs_mesh_config(priv, CMD_ACT_MESH_CONFIG_START, 1))
priv->mesh_tlv = 0;
}
} else
if ((MRVL_FW_MAJOR_REV(priv->fwrelease) >= MRVL_FW_V10) &&
(priv->fwcapinfo & MESH_CAPINFO_ENABLE_MASK)) {
/*
*/
priv->mesh_tlv = TLV_TYPE_MESH_ID;
if (lbs_mesh_config(priv, CMD_ACT_MESH_CONFIG_START, 1))
priv->mesh_tlv = 0;
}
/* */
lbs_mesh_config(priv, CMD_ACT_MESH_CONFIG_STOP, 1);
if (priv->mesh_tlv) {
sprintf(priv->mesh_ssid, "mesh");
priv->mesh_ssid_len = 4;
ret = 1;
}
lbs_deb_leave_args(LBS_DEB_MESH, "ret %d", ret);
return ret;
}
