/*
* \brief Handles interrupts issued due to end of transmission
*
* \param underrun_occured true if under-run has occurred
*/
void handle_tx_end_irq(bool underrun_occured)
{
#if ((MAC_START_REQUEST_CONFIRM == 1) && (defined BEACON_SUPPORT))
if (tal_beacon_transmission) {
tal_beacon_transmission = false;
if (tal_csma_state == BACKOFF_WAITING_FOR_BEACON) {
/* Slotted CSMA has been waiting for a beacon, now it
* can continue. */
tal_csma_state = CSMA_HANDLE_BEACON;
}
} else
#endif /* ((MAC_START_REQUEST_CONFIRM == 1) && (defined BEACON_SUPPORT)) */
{
#if (defined BEACON_SUPPORT) || (defined ENABLE_TSTAMP)
/*
* Store tx timestamp to frame_info_t structure.
* The timestamping is only required for beaconing networks
* or if timestamping is explicitly enabled.
*/
pal_trx_read_timestamp(&mac_frame_ptr->time_stamp);
#endif /* #if (defined BEACON_SUPPORT) || (defined ENABLE_TSTAMP) */
/* Read trac status before enabling RX_AACK_ON. */
if (underrun_occured) {
trx_trac_status = TRAC_INVALID;
} else {
trx_trac_status = (trx_trac_status_t)trx_bit_read(
SR_TRAC_STATUS);
}
#ifdef BEACON_SUPPORT
if (tal_csma_state == FRAME_SENDING) { /* Transmission was
* issued by slotted CSMA
**/
PIN_TX_END();
tal_state = TAL_SLOTTED_CSMA;
/* Map status message of transceiver to TAL constants.
**/
switch (trx_trac_status) {
case TRAC_SUCCESS_DATA_PENDING:
PIN_ACK_OK_START();
tal_csma_state = TX_DONE_FRAME_PENDING;
break;
case TRAC_SUCCESS:
PIN_ACK_OK_START();
tal_csma_state = TX_DONE_SUCCESS;
break;
case TRAC_CHANNEL_ACCESS_FAILURE:
PIN_NO_ACK_START();
tal_csma_state = CSMA_ACCESS_FAILURE;
break;
case TRAC_NO_ACK:
PIN_NO_ACK_START();
tal_csma_state = TX_DONE_NO_ACK;
break;
case TRAC_INVALID: /* Handle this in the same way as
* default. */
default:
Assert("not handled trac status" == 0);
tal_csma_state = CSMA_ACCESS_FAILURE;
break;
}
PIN_ACK_OK_END();
PIN_ACK_WAITING_END();
} else
#endif /* BEACON_SUPPORT */
/* Trx has handled the entire transmission incl. CSMA */
{
tal_state = TAL_TX_DONE; /* Further handling is done by
* tx_done_handling() */
}
}
/*
* After transmission has finished, switch receiver on again.
* Check if receive buffer is available.
*/
if (NULL == tal_rx_buffer) {
set_trx_state(CMD_PLL_ON);
tal_rx_on_required = true;
} else {
set_trx_state(CMD_RX_AACK_ON);
}
}
/*
* \brief Handles interrupts issued due to end of transmission
*/
void handle_tx_end_irq(void)
{
/* Check if TX_END interrupt, is issued due to automatic ACK
* transmission. */
#if ((MAC_START_REQUEST_CONFIRM == 1) && (defined BEACON_SUPPORT))
if ((tal_state != TAL_TX_AUTO) && (!tal_beacon_transmission))
#else
if (tal_state != TAL_TX_AUTO)
#endif
{
/* Automatic ACK transmission completed -> No further
* processing. */
return;
}
#if ((MAC_START_REQUEST_CONFIRM == 1) && (defined BEACON_SUPPORT))
if (tal_beacon_transmission) {
tal_beacon_transmission = false;
if (tal_csma_state == BACKOFF_WAITING_FOR_BEACON) {
/* Slotted CSMA has been waiting for a beacon, now it
* can continue. */
tal_csma_state = CSMA_HANDLE_BEACON;
}
} else
#endif /* ((MAC_START_REQUEST_CONFIRM == 1) && (defined BEACON_SUPPORT)) */
{
/* Read trac status before enabling RX_AACK_ON. */
trx_trac_status = (trx_trac_status_t)trx_bit_read(
SR_TRAC_STATUS);
#ifdef BEACON_SUPPORT
if (tal_csma_state == FRAME_SENDING) { /* Transmission was
* issued by slotted CSMA
**/
PIN_TX_END();
tal_state = TAL_SLOTTED_CSMA;
/* Map status message of transceiver to TAL constants.
**/
switch (trx_trac_status) {
case TRAC_SUCCESS_DATA_PENDING:
PIN_ACK_OK_START();
tal_csma_state = TX_DONE_FRAME_PENDING;
break;
case TRAC_SUCCESS:
PIN_ACK_OK_START();
tal_csma_state = TX_DONE_SUCCESS;
break;
case TRAC_CHANNEL_ACCESS_FAILURE:
PIN_NO_ACK_START();
tal_csma_state = CSMA_ACCESS_FAILURE;
break;
case TRAC_NO_ACK:
PIN_NO_ACK_START();
tal_csma_state = TX_DONE_NO_ACK;
break;
case TRAC_INVALID: /* Handle this in the same way as
* default. */
default:
Assert("not handled trac status" == 0);
tal_csma_state = CSMA_ACCESS_FAILURE;
break;
}
PIN_ACK_OK_END();
PIN_ACK_WAITING_END();
} else
#endif /* BEACON_SUPPORT */
/* Trx has handled the entire transmission incl. CSMA */
{
tal_state = TAL_TX_DONE; /* Further handling is done by
* tx_done_handling() */
}
}
/*
* After transmission has finished, switch receiver on again.
* Check if receive buffer is available.
*/
if (NULL == tal_rx_buffer) {
set_trx_state(CMD_PLL_ON);
tal_rx_on_required = true;
} else {
set_trx_state(CMD_RX_AACK_ON);
}
}
/**
* \brief Interrupt handler for ACK reception
*
* \param parameter Unused callback parameter
*/
static void ack_reception_handler_cb(void *parameter)
{
trx_irq_reason_t trx_irq_cause;
if (tal_csma_state == TX_DONE_NO_ACK) {
return; /* ack expiration timer has already been fired */
}
trx_irq_cause = (trx_irq_reason_t)pal_trx_reg_read(RG_IRQ_STATUS);
if (trx_irq_cause & TRX_IRQ_TRX_END) {
retval_t timer_status;
switch (tal_csma_state) {
case FRAME_SENDING_WITH_ACK:
set_trx_state(CMD_RX_ON);
timer_status
= pal_timer_start(TAL_ACK_WAIT_TIMER,
TAL_CONVERT_SYMBOLS_TO_US(
TAL_ACK_WAIT_DURATION_DEFAULT),
TIMEOUT_RELATIVE,
(FUNC_PTR)ack_timer_expiry_handler_cb,
NULL);
if (timer_status == MAC_SUCCESS) {
tal_csma_state = WAITING_FOR_ACK;
} else if (timer_status == PAL_TMR_ALREADY_RUNNING) {
tal_csma_state = WAITING_FOR_ACK;
} else {
tal_csma_state = TX_DONE_NO_ACK;
Assert("timer start failed" == 0);
}
/* debug pin to switch on: define ENABLE_DEBUG_PINS,
*pal_config.h */
PIN_TX_END();
PIN_ACK_WAITING_START();
break;
case WAITING_FOR_ACK:
{
uint8_t ack_frame[ACK_FRAME_LEN + LENGTH_FIELD_LEN];
/*
* Read the frame buffer, identify if this is an ACK
*frame,
* and get the sequence number.
* Üpload the frame from the transceiver.
*/
pal_trx_frame_read(ack_frame,
(ACK_FRAME_LEN +
LENGTH_FIELD_LEN));
/* Check if the uploaded frame is an ACK frame */
if ((ack_frame[1] & ACK_FRAME) != ACK_FRAME) {
/* The received frame is not an ACK frame */
return;
}
/* check CRC */
if (pal_trx_bit_read(SR_RX_CRC_VALID) != CRC16_VALID) {
return;
}
/* check the sequence number */
if (ack_frame[3] == tal_frame_to_tx[SEQ_NUMBER_POS]) {
/*
* If we are here, the ACK is valid and matches
* the transmitted sequence number.
*/
pal_timer_stop(TAL_ACK_WAIT_TIMER);
#if (_DEBUG_ > 0)
if (pal_is_timer_running(TAL_ACK_WAIT_TIMER)) {
Assert("Ack timer running" == 0);
}
#endif
/* restore the interrupt handler */
pal_trx_irq_init((FUNC_PTR)trx_irq_handler_cb);
pal_trx_irq_en();
if (NULL != tal_rx_buffer) {
pal_trx_reg_write(RG_TRX_STATE,
CMD_RX_AACK_ON);
} else {
tal_rx_on_required = true;
}
/* debug pin to switch on: define
*ENABLE_DEBUG_PINS, pal_config.h */
PIN_ACK_OK_START();
if (ack_frame[1] & FCF_FRAME_PENDING) {
tal_csma_state = TX_DONE_FRAME_PENDING;
} else {
tal_csma_state = TX_DONE_SUCCESS;
}
/* debug pin to switch on: define
*ENABLE_DEBUG_PINS, pal_config.h */
PIN_ACK_OK_END();
PIN_ACK_WAITING_END();
}
}
break;
case FRAME_SENDING_NO_ACK:
/* Tx is done */
/* debug pin to switch on: define ENABLE_DEBUG_PINS,
*pal_config.h */
PIN_TX_END();
tal_csma_state = TX_DONE_SUCCESS;
break;
default:
Assert("unknown tal_csma_state" == 0);
break;
}
} else { /* other interrupt than TRX_END */
/* no interest in any other interrupt */
return;
}
parameter = parameter; /* Keep compiler happy. */
}
