//*****************************************************************************
//
// The interrupt handler for the for PWM0 interrupts.
//
//*****************************************************************************
void
PWM0IntHandler(void)
{
//
// Clear the PWM0 LOAD interrupt flag. This flag gets set when the PWM
// counter gets reloaded.
//
PWMGenIntClear(PWM_BASE, PWM_GEN_0, PWM_INT_CNT_LOAD);
//
// If the duty cycle is less or equal to 75% then add 0.1% to the duty
// cycle. Else, reset the duty cycle to 0.1% cycles. Note that 64 is
// 0.01% of the period (64000 cycles).
//
if((PWMPulseWidthGet(PWM_BASE, PWM_OUT_0) + 64) <=
((PWMGenPeriodGet(PWM_BASE, PWM_GEN_0) * 3) / 4))
{
PWMPulseWidthSet(PWM_BASE, PWM_OUT_0,
PWMPulseWidthGet(PWM_BASE, PWM_OUT_0) + 64);
}
else
{
PWMPulseWidthSet(PWM_BASE, PWM_OUT_0, 64);
}
}
int main(void)
{
SysCtlClockSet(SYSCTL_SYSDIV_4|SYSCTL_USE_PLL|SYSCTL_XTAL_16MHZ|SYSCTL_OSC_MAIN);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA); // Enable the GPIO A ports
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE); // Enable the GPIO E ports
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
SysCtlPeripheralEnable(SYSCTL_PERIPH_PWM0);
GPIOPinConfigure(GPIO_PB6_M0PWM0);
GPIOPinTypePWM(GPIO_PORTB_BASE, GPIO_PIN_6);
GPIOPinConfigure(GPIO_PB7_M0PWM1);
GPIOPinTypePWM(GPIO_PORTB_BASE, GPIO_PIN_7);
PWMGenConfigure(PWM0_BASE, PWM_GEN_0, PWM_GEN_MODE_DOWN | PWM_GEN_MODE_NO_SYNC);
PWMGenPeriodSet(PWM0_BASE, PWM_GEN_0, 6400000);
PWMPulseWidthSet(PWM0_BASE, PWM_OUT_0, PWMGenPeriodGet(PWM0_BASE, PWM_GEN_0) / 1.25);
PWMOutputState(PWM0_BASE, PWM_OUT_0_BIT, true);
PWMGenEnable(PWM0_BASE, PWM_GEN_0);
PWMGenConfigure(PWM0_BASE, PWM_GEN_1, PWM_GEN_MODE_DOWN | PWM_GEN_MODE_NO_SYNC);
PWMGenPeriodSet(PWM0_BASE, PWM_GEN_1, 6400000);
PWMPulseWidthSet(PWM0_BASE, PWM_OUT_1, PWMGenPeriodGet(PWM0_BASE, PWM_GEN_1) / 1.25);
PWMOutputState(PWM0_BASE, PWM_OUT_1_BIT, true);
PWMGenEnable(PWM0_BASE, PWM_GEN_1);
GPIOPinTypeGPIOOutput(GPIO_PORTA_BASE, GPIO_PIN_6|GPIO_PIN_7); // Set pin 7 as the output port
GPIOPinTypeGPIOOutput(GPIO_PORTE_BASE, GPIO_PIN_1|GPIO_PIN_2);
GPIOPinTypeGPIOOutput(GPIO_PORTA_BASE, GPIO_PIN_5);
GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_6|GPIO_PIN_7,64); // Give '1' to pin 7
GPIOPinWrite(GPIO_PORTE_BASE,GPIO_PIN_1|GPIO_PIN_2,4);
while(1)
{
GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_6|GPIO_PIN_7,64); // Give '1' to pin 7
GPIOPinWrite(GPIO_PORTE_BASE,GPIO_PIN_1|GPIO_PIN_2,4);
SysCtlDelay(4000000*10);
GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_6|GPIO_PIN_7,0); // Give '1' to pin 7
GPIOPinWrite(GPIO_PORTE_BASE,GPIO_PIN_1|GPIO_PIN_2,0);
GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_5,32);
SysCtlDelay(400000);
GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_5,0);
GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_6|GPIO_PIN_7,128); // Give '1' to pin 7
GPIOPinWrite(GPIO_PORTE_BASE,GPIO_PIN_1|GPIO_PIN_2,2);
SysCtlDelay(4000000*10);
GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_6|GPIO_PIN_7,0); // Give '1' to pin 7
GPIOPinWrite(GPIO_PORTE_BASE,GPIO_PIN_1|GPIO_PIN_2,0);
GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_5,32);
SysCtlDelay(400000);
GPIOPinWrite(GPIO_PORTA_BASE,GPIO_PIN_5,0);
}
}
void tr_motors(uint8_t duty, uint8_t num_cells)
{
// Change State counter on drive task
drivestate = DRIVESTATE_STRAFERIGHT;
// Set num of turns wanted
num_moves = num_cells;
// Set duty cycle
dutycycle = duty;
// Set periods on Motors
uint32_t period = PWMGenPeriodGet(PWM_MOTOR_BASE, PWM_GEN_TOPM);
PWMPulseWidthSet(PWM_MOTOR_BASE, M1_OUT, ((duty * period)/100));
PWMPulseWidthSet(PWM_MOTOR_BASE, M2_OUT, ((duty * period)/100));
PWMPulseWidthSet(PWM_MOTOR_BASE, M3_OUT, ((duty * period)/100));
PWMPulseWidthSet(PWM_MOTOR_BASE, M4_OUT, ((duty * period)/100));
// Control Pins
//M1:FWD, M2:REV, M3:REV, M4:FWD
//M1:FWD, 1A hi, 1B lo
GPIOPinWrite(GPIO_PORTD_BASE, PD2_M1A | PD3_M1B, PD2_M1A);
//M2:REV, 2A lo, 2B hi, M3:REV, 3A lo
GPIOPinWrite(GPIO_PORTE_BASE, PE1_M2A | PE2_M2B | PE3_M3A, PE2_M2B);
//M3:REV, 3B hi
GPIOPinWrite(GPIO_PORTA_BASE, PA5_M3B, PA5_M3B);
//M4:FWD, 4A hi, 4B lo
GPIOPinWrite(GPIO_PORTB_BASE, PB4_M4A | PB5_M4B, PB4_M4A);
}
void rampGenericPWM(bool rampDirection, uint32_t pwmBase, uint32_t pwm,
uint32_t pwmBit, uint32_t delay) {
// Start value is the current PWM pulse width regardless the ramp direction
uint32_t i = PWMPulseWidthGet(pwmBase, pwm);
if (rampDirection == PWM_RAMP_UP) {
uint32_t targetPwmLoad = PWMGenPeriodGet(pwmBase, PWM_GEN_3);
PWMOutputState(pwmBase, pwmBit, true);
for (; i < targetPwmLoad; i += PWM_STEP)
{
PWMPulseWidthSet(pwmBase, pwm, i);
SysCtlDelay(delay);
}
} else // rampDirection == PWM_RAMP_DOWN
{
for (; i > PWM_LOW; i -= PWM_STEP)
{
PWMPulseWidthSet(pwmBase, pwm, i);
SysCtlDelay(delay);
}
PWMOutputState(pwmBase, pwmBit, false);
}
}
void setDC(int32_t * DCmotors)
{
uint32_t period = PWMGenPeriodGet(PWM_MOTOR_BASE, PWM_GEN_TOPM);
PWMPulseWidthSet(PWM_MOTOR_BASE, M1_OUT, (((DCmotors[0] * period)/100))-1);
PWMPulseWidthSet(PWM_MOTOR_BASE, M2_OUT, (((DCmotors[1] * period)/100))-1);
PWMPulseWidthSet(PWM_MOTOR_BASE, M3_OUT, (((DCmotors[2] * period)/100))-1);
PWMPulseWidthSet(PWM_MOTOR_BASE, M4_OUT, (((DCmotors[3] * period)/100))-1);
}
void bsp_lcd_bright_control(uint8 duty)
{
if(duty){
PWMOutputState(PWM0_BASE, PWM_OUT_0_BIT, 1);
PWMPulseWidthSet(PWM0_BASE, PWM_OUT_0, duty*PWMGenPeriodGet(PWM0_BASE,PWM_GEN_0)/100);
}else{
PWMOutputState(PWM0_BASE, PWM_OUT_0_BIT, 0);
}
}
/*
* ======== PWMTiva_getPeriodCounts ========
* @pre Function assumes that handle is not NULL
*/
unsigned int PWMTiva_getPeriodCounts(PWM_Handle handle)
{
unsigned int key;
unsigned int period;
PWMTiva_HWAttrs const *hwAttrs = handle->hwAttrs;
key = Hwi_disable();
period = PWMGenPeriodGet(hwAttrs->baseAddr, hwAttrs->pwmOutput & PWM_GEN_MASK);
Hwi_restore(key);
return period;
}
void stop_motors(uint8_t duty)
{
// Change State counter on drive task
drivestate = DRIVESTATE_IDLE;
dutycycle = duty;
// Set periods on Motors
uint32_t period = PWMGenPeriodGet(PWM_MOTOR_BASE, PWM_GEN_TOPM);
PWMPulseWidthSet(PWM_MOTOR_BASE, M1_OUT, (((100 * period)/100) - 1));
PWMPulseWidthSet(PWM_MOTOR_BASE, M2_OUT, (((100 * period)/100) - 1));
PWMPulseWidthSet(PWM_MOTOR_BASE, M3_OUT, (((100 * period)/100) - 1));
PWMPulseWidthSet(PWM_MOTOR_BASE, M4_OUT, (((100 * period)/100) - 1));
// Set all motors to brake
GPIOPinWrite(GPIO_PORTD_BASE, PD2_M1A | PD3_M1B, PD2_M1A | PD3_M1B);
GPIOPinWrite(GPIO_PORTE_BASE, PE1_M2A | PE2_M2B | PE3_M3A, PE1_M2A | PE2_M2B | PE3_M3A);
GPIOPinWrite(GPIO_PORTA_BASE, PA5_M3B, PA5_M3B);
GPIOPinWrite(GPIO_PORTB_BASE, PB4_M4A | PB5_M4B, PB4_M4A | PB5_M4B);
}
void bsp_pwm0_init(void)
{
/*Enable device*/
SysCtlPeripheralEnable(SYSCTL_PERIPH_PWM0);
/*Set clock divider*/
PWMClockSet(PWM0_BASE,PWM_SYSCLK_DIV_64);
/*Enable PWM pin*/
GPIOPinConfigure(LCD_PWM_CHANNEL);
GPIOPinTypePWM(LCD_PWM_PORT, LCD_PWM_PIN);
/*Configure PWM generator*/
PWMGenConfigure(PWM0_BASE, PWM_GEN_0,(PWM_GEN_MODE_DOWN | PWM_GEN_MODE_NO_SYNC));
/*Set PWM timer period*/
PWMGenPeriodSet(PWM0_BASE, PWM_GEN_0,gSysClock/10000);
/*Set width for PWM0*/
PWMPulseWidthSet(PWM0_BASE, PWM_OUT_0, 50*PWMGenPeriodGet(PWM0_BASE,PWM_GEN_0)/100);
/*Enable output*/
PWMOutputState(PWM0_BASE, PWM_OUT_0_BIT, 0);
/*Enable Generator*/
PWMGenEnable(PWM0_BASE, PWM_GEN_0);
}
void bsp_pwm_for_sense_init(void)
{
/*Enable device*/
SysCtlPeripheralEnable(SYSCTL_PERIPH_PWM0);
/*Set clock divider*/
PWMClockSet(PWM0_BASE,PWM_SYSCLK_DIV_1);
/*Enable PWM pin*/
GPIOPinConfigure(GPIO_PK5_M0PWM7);
GPIOPinTypePWM(SENSE_THRES_PORT, SENSE_THRES_PIN);
/*Configure PWM generator*/
PWMGenConfigure(PWM0_BASE, PWM_GEN_3,(PWM_GEN_MODE_DOWN | PWM_GEN_MODE_NO_SYNC));
/*Set PWM timer period*/
PWMGenPeriodSet(PWM0_BASE, PWM_GEN_3,gSysClock/1000000);
/*Set width for PWM0*/
PWMPulseWidthSet(PWM0_BASE, PWM_OUT_7, 1*PWMGenPeriodGet(PWM0_BASE,PWM_GEN_3)/5);
/*ensable output*/
PWMOutputState(PWM0_BASE, PWM_OUT_7_BIT, 1);
/*Enable Generator*/
PWMGenEnable(PWM0_BASE, PWM_GEN_3);
}
void quad_pwm_init(void)
{
// Motor 1:Port D pin 0 (PD0)
// Motor 2:Port D pin 1 (PD1)
// Motor 3:Port A pin 6 (PA6)
// Motor 4:Port A pin 7 (PA7)
// Red LED: Port F pin 1 (PF1)
// Blu LED: Port F pin 2 (PF2)
// Grn LED: Port F pin 3 (PF3)
SysCtlPWMClockSet(SYSCTL_PWMDIV_32);
//Enable the peripheral devices/ports
SysCtlPeripheralEnable(SYSCTL_PERIPH_PWM1);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
//Enable LED
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
GPIOPinConfigure(GPIO_PD0_M1PWM0); //motors 3
GPIOPinConfigure(GPIO_PD1_M1PWM1); //motors 4
GPIOPinConfigure(GPIO_PA6_M1PWM2); //motors 1
GPIOPinConfigure(GPIO_PA7_M1PWM3); //motors 2
GPIOPinConfigure(GPIO_PF1_M1PWM5); //red led
GPIOPinConfigure(GPIO_PF2_M1PWM6); //blue led
GPIOPinConfigure(GPIO_PF3_M1PWM7); //green led
//motos 1 and 2
GPIOPinTypePWM(GPIO_PORTA_BASE, GPIO_PIN_6);
GPIOPinTypePWM(GPIO_PORTA_BASE, GPIO_PIN_7);
//motors 3 and 4
GPIOPinTypePWM(GPIO_PORTD_BASE, GPIO_PIN_0);
GPIOPinTypePWM(GPIO_PORTD_BASE, GPIO_PIN_1);
//the RGB LED
GPIOPinTypePWM(GPIO_PORTF_BASE, GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3);
//motors config
PWMGenConfigure(PWM1_BASE, PWM_GEN_0, PWM_GEN_MODE_DOWN);
PWMGenConfigure(PWM1_BASE, PWM_GEN_1, PWM_GEN_MODE_DOWN);
//led config
PWMGenConfigure(PWM1_BASE, PWM_GEN_2, PWM_GEN_MODE_DOWN);
PWMGenConfigure(PWM1_BASE, PWM_GEN_3, PWM_GEN_MODE_DOWN);
//motors 周期配置
PWMGenPeriodSet(PWM1_BASE, PWM_GEN_0, 40000);
PWMGenPeriodSet(PWM1_BASE, PWM_GEN_1, 40000);
//led
PWMGenPeriodSet(PWM1_BASE, PWM_GEN_2, 65530);
PWMGenPeriodSet(PWM1_BASE, PWM_GEN_3, 65530);
//motors pluse width config
PWMPulseWidthSet(PWM1_BASE, PWM_OUT_0,
PWMGenPeriodGet(PWM1_BASE, PWM_OUT_0) / 2);
PWMPulseWidthSet(PWM1_BASE, PWM_OUT_1,
PWMGenPeriodGet(PWM1_BASE, PWM_OUT_0) / 2);
PWMPulseWidthSet(PWM1_BASE, PWM_OUT_2,
PWMGenPeriodGet(PWM1_BASE, PWM_OUT_0) / 2);
PWMPulseWidthSet(PWM1_BASE, PWM_OUT_3,
PWMGenPeriodGet(PWM1_BASE, PWM_OUT_0) / 2);
//led pulse width config
PWMPulseWidthSet(PWM1_BASE, PWM_OUT_5,
PWMGenPeriodGet(PWM1_BASE, PWM_OUT_0) / 2);
PWMPulseWidthSet(PWM1_BASE, PWM_OUT_6,
PWMGenPeriodGet(PWM1_BASE, PWM_OUT_0) / 2);
PWMPulseWidthSet(PWM1_BASE, PWM_OUT_7,
PWMGenPeriodGet(PWM1_BASE, PWM_OUT_0) / 2);
PWMOutputState(PWM1_BASE, PWM_OUT_0_BIT, true); //motors 1
PWMOutputState(PWM1_BASE, PWM_OUT_1_BIT, true); //motors 2
PWMOutputState(PWM1_BASE, PWM_OUT_2_BIT, true); //motors 3
PWMOutputState(PWM1_BASE, PWM_OUT_3_BIT, true); //motors 4
PWMOutputState(PWM1_BASE, PWM_OUT_5_BIT, true); //red led
PWMOutputState(PWM1_BASE, PWM_OUT_6_BIT, true); //blue led
PWMOutputState(PWM1_BASE, PWM_OUT_7_BIT, true); //green led
PWMGenEnable(PWM1_BASE, PWM_GEN_0);
PWMGenEnable(PWM1_BASE, PWM_GEN_1);
PWMGenEnable(PWM1_BASE, PWM_GEN_2);
PWMGenEnable(PWM1_BASE, PWM_GEN_3);
}
void bsp_pwm_for_sense_set(uint16 x, uint16 y)
{
if(x <= y){
PWMPulseWidthSet(PWM0_BASE, PWM_OUT_7, x*PWMGenPeriodGet(PWM0_BASE,PWM_GEN_3)/y);
}
}
//*****************************************************************************
//
// Configure PWM0 for a 25% duty cycle signal running at 250Hz. This example
// also shows how to invert the PWM signal every 5 seconds for 5 seconds.
//
//*****************************************************************************
int
main(void)
{
//
// Set the clocking to run directly from the external crystal/oscillator.
// TODO: The SYSCTL_XTAL_ value must be changed to match the value of the
// crystal on your board.
//
SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Set the PWM clock to the system clock.
//
SysCtlPWMClockSet(SYSCTL_PWMDIV_1);
//
// Set up the serial console to use for displaying messages. This is
// just for this example program and is not needed for Timer operation.
//
InitConsole();
//
// Display the setup on the console.
//
UARTprintf("PWM ->\n");
UARTprintf(" Module: PWM0\n");
UARTprintf(" Pin: PD0\n");
UARTprintf(" Configured Duty Cycle: 25%%\n");
UARTprintf(" Inverted Duty Cycle: 75%%\n");
UARTprintf(" Features: PWM output inversion every 5 seconds.\n\n");
UARTprintf("Generating PWM on PWM0 (PD0) -> State = ");
//
// The PWM peripheral must be enabled for use.
//
SysCtlPeripheralEnable(SYSCTL_PERIPH_PWM0);
//
// For this example PWM0 is used with PortB Pin6. The actual port and
// pins used may be different on your part, consult the data sheet for
// more information.
// GPIO port B needs to be enabled so these pins can be used.
// TODO: change this to whichever GPIO port you are using.
//
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
//
// Configure the GPIO pin muxing to select PWM00 functions for these pins.
// This step selects which alternate function is available for these pins.
// This is necessary if your part supports GPIO pin function muxing.
// Consult the data sheet to see which functions are allocated per pin.
// TODO: change this to select the port/pin you are using.
//
GPIOPinConfigure(GPIO_PB6_M0PWM0);
//
// Configure the PWM function for this pin.
// Consult the data sheet to see which functions are allocated per pin.
// TODO: change this to select the port/pin you are using.
//
GPIOPinTypePWM(GPIO_PORTB_BASE, GPIO_PIN_6);
//
// Configure the PWM0 to count up/down without synchronization.
//
PWMGenConfigure(PWM0_BASE, PWM_GEN_0, PWM_GEN_MODE_UP_DOWN |
PWM_GEN_MODE_NO_SYNC);
//
// Set the PWM period to 250Hz. To calculate the appropriate parameter
// use the following equation: N = (1 / f) * SysClk. Where N is the
// function parameter, f is the desired frequency, and SysClk is the
// system clock frequency.
// In this case you get: (1 / 250Hz) * 16MHz = 64000 cycles. Note that
// the maximum period you can set is 2^16.
// TODO: modify this calculation to use the clock frequency that you are
// using.
//
PWMGenPeriodSet(PWM0_BASE, PWM_GEN_0, 64000);
//
// Set PWM0 to a duty cycle of 25%. You set the duty cycle as a function
// of the period. Since the period was set above, you can use the
// PWMGenPeriodGet() function. For this example the PWM will be high for
// 25% of the time or 16000 clock ticks (64000 / 4).
//
PWMPulseWidthSet(PWM0_BASE, PWM_OUT_0,
PWMGenPeriodGet(PWM0_BASE, PWM_OUT_0) / 4);
//
// Enable the PWM0 Bit0 (PD0) output signal.
//
PWMOutputState(PWM0_BASE, PWM_OUT_0_BIT, true);
//
// Enable the PWM generator block.
//
PWMGenEnable(PWM0_BASE, PWM_GEN_0);
//
// Loop forever while the PWM signals are generated.
//
while(1)
{
//
// Print out that the level of PWM is normal.
//
UARTprintf("Normal \b\b\b\b\b\b\b\b");
//
// This function provides a means of generating a constant length
// delay. The function delay (in cycles) = 3 * parameter. Delay
// 5 seconds arbitrarily.
//
SysCtlDelay((SysCtlClockGet() * 5) / 3);
//
// Invert PWM0 signal.
//
PWMOutputInvert(PWM0_BASE, PWM_OUT_0_BIT, true);
//
// Print out that the level of PWM is inverted.
//
UARTprintf("Inverted\b\b\b\b\b\b\b\b");
//
// This function provides a means of generating a constant length
// delay. The function delay (in cycles) = 3 * parameter. Delay
// 5 seconds arbitrarily.
//
SysCtlDelay((SysCtlClockGet() * 5) / 3);
//
// Switch PWM0 signal back to regular operation.
//
PWMOutputInvert(PWM0_BASE, PWM_OUT_0_BIT, false);
}
}
//*****************************************************************************
//
// Configure the PWM0 block with dead-band generation. The example configures
// the PWM0 block to generate a 25% duty cycle signal on PD0 with dead-band
// generation. This will produce a complement of PD0 on PD1 (75% duty cycle).
// The dead-band generator is set to have a 10us or 160 cycle delay
// (160cycles / 16Mhz = 10us) on the rising and falling edges of the PD0 PWM
// signal.
//
//*****************************************************************************
int
main(void)
{
//
// Set the clocking to run directly from the external crystal/oscillator.
// TODO: The SYSCTL_XTAL_ value must be changed to match the value of the
// crystal on your board.
//
SysCtlClockSet(SYSCTL_SYSDIV_1 | SYSCTL_USE_OSC | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Set the PWM clock to the system clock.
//
SysCtlPWMClockSet(SYSCTL_PWMDIV_1);
//
// Set up the serial console to use for displaying messages. This is just
// for this example program and is not needed for PWM operation.
//
InitConsole();
//
// Display the setup on the console.
//
UARTprintf("PWM ->\n");
UARTprintf(" Module: PWM0\n");
UARTprintf(" Pin(s): PD0 and PD1\n");
UARTprintf(" Features: Dead-band Generation\n");
UARTprintf(" Duty Cycle: 25%% on PD0 and 75%% on PD1\n");
UARTprintf(" Dead-band Length: 160 cycles on rising and falling edges\n\n");
UARTprintf("Generating PWM on PWM0 (PD0) -> ");
//
// The PWM peripheral must be enabled for use.
//
SysCtlPeripheralEnable(SYSCTL_PERIPH_PWM);
//
// For this example PWM0 is used with PortD Pins 0 and 1. The actual port
// and pins used may be different on your part, consult the data sheet for
// more information. GPIO port D needs to be enabled so these pins can be
// used.
// TODO: change this to whichever GPIO port you are using.
//
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
//
// Configure the GPIO pin muxing to select PWM functions for these pins.
// This step selects which alternate function is available for these pins.
// This is necessary if your part supports GPIO pin function muxing.
// Consult the data sheet to see which functions are allocated per pin.
// TODO: change this to select the port/pin you are using.
//
GPIOPinConfigure(GPIO_PD0_PWM0);
GPIOPinConfigure(GPIO_PD1_PWM1);
//
// Configure the GPIO pad for PWM function on pins PD0 and PD1. Consult
// the data sheet to see which functions are allocated per pin.
// TODO: change this to select the port/pin you are using.
//
GPIOPinTypePWM(GPIO_PORTD_BASE, GPIO_PIN_0);
GPIOPinTypePWM(GPIO_PORTD_BASE, GPIO_PIN_1);
//
// Configure the PWM0 to count up/down without synchronization.
// Note: Enabling the dead-band generator automatically couples the 2
// outputs from the PWM block so we don't use the PWM synchronization.
//
PWMGenConfigure(PWM_BASE, PWM_GEN_0, PWM_GEN_MODE_UP_DOWN |
PWM_GEN_MODE_NO_SYNC);
//
// Set the PWM period to 250Hz. To calculate the appropriate parameter
// use the following equation: N = (1 / f) * SysClk. Where N is the
// function parameter, f is the desired frequency, and SysClk is the
// system clock frequency.
// In this case you get: (1 / 250Hz) * 16MHz = 64000 cycles. Note that
// the maximum period you can set is 2^16 - 1.
// TODO: modify this calculation to use the clock frequency that you are
// using.
//
PWMGenPeriodSet(PWM_BASE, PWM_GEN_0, 64000);
//
// Set PWM0 PD0 to a duty cycle of 25%. You set the duty cycle as a
// function of the period. Since the period was set above, you can use the
// PWMGenPeriodGet() function. For this example the PWM will be high for
// 25% of the time or 16000 clock cycles (64000 / 4).
//
PWMPulseWidthSet(PWM_BASE, PWM_OUT_0,
PWMGenPeriodGet(PWM_BASE, PWM_OUT_0) / 4);
//
// Enable the dead-band generation on the PWM0 output signal. PWM bit 0
// (PD0), will have a duty cycle of 25% (set above) and PWM bit 1 will have
// a duty cycle of 75%. These signals will have a 10us gap between the
// rising and falling edges. This means that before PWM bit 1 goes high,
// PWM bit 0 has been low for at LEAST 160 cycles (or 10us) and the same
// before PWM bit 0 goes high. The dead-band generator lets you specify
// the width of the "dead-band" delay, in PWM clock cycles, before the PWM
// signal goes high and after the PWM signal falls. For this example we
// will use 160 cycles (or 10us) on both the rising and falling edges of
// PD0. Reference the datasheet for more information on dead-band
// generation.
//
PWMDeadBandEnable(PWM_BASE, PWM_GEN_0, 160, 160);
//
// Enable the PWM0 Bit 0 (PD0) and Bit 1 (PD1) output signals.
//
PWMOutputState(PWM_BASE, PWM_OUT_1_BIT | PWM_OUT_0_BIT, true);
//
// Enables the counter for a PWM generator block.
//
PWMGenEnable(PWM_BASE, PWM_GEN_0);
//
// Loop forever while the PWM signals are generated.
//
while(1)
{
//
// Print out indication on the console that the program is running.
//
PrintRunningDots();
}
}
/*
* ======== PWMTiva_setDuty ========
* @pre Function assumes that handle is not NULL
*/
void PWMTiva_setDuty(PWM_Handle handle, uint32_t duty)
{
unsigned int key;
uint8_t maxDutySet;
uint16_t period;
uint16_t pwmGenerator;
uint16_t pwmGenPeriod;
uint32_t newDuty;
PWMTiva_Object *object = handle->object;
PWMTiva_HWAttrs const *hwAttrs = handle->hwAttrs;
/* Get the PWM generator, generator period and instance output bit */
pwmGenerator = hwAttrs->pwmOutput & PWM_GEN_MASK;
pwmGenPeriod = *(object->pwmStatus)->genPeriods +
((hwAttrs->pwmOutput / PWM_OUT_0) - 1);
/* Get the generator period */
period = PWMGenPeriodGet(hwAttrs->baseAddr, pwmGenerator);
switch(object->dutyMode) {
case PWM_DUTY_COUNTS:
/* Duty specified as PWM timer counts */
Assert_isTrue(duty <= period, NULL);
maxDutySet = (duty >= period);
newDuty = (duty && duty < period) ? duty : period;
break;
case PWM_DUTY_TIME:
/* Duty is specified in microseconds */
Assert_isTrue(duty <= pwmGenPeriod, NULL);
maxDutySet = (duty >= pwmGenPeriod);
newDuty = (duty * (object->pwmStatus)->cyclesPerMicroSec) /
(object->pwmStatus)->prescalar;
if (!(newDuty) || newDuty > period) {
newDuty = period;
}
break;
case PWM_DUTY_SCALAR:
/* Duty specified as a number [0 - 65535] scaled to the period */
Assert_isTrue(duty <= PWMTiva_MAX_MATCH_VALUE, NULL);
maxDutySet = (duty >= PWMTiva_MAX_MATCH_VALUE);
newDuty = period;
if (duty && duty < PWMTiva_MAX_MATCH_VALUE) {
newDuty = (newDuty * 100) / PWMTiva_MAX_MATCH_VALUE;
newDuty = (newDuty * duty) / 100;
if (!newDuty) {
newDuty++;
}
}
break;
default:
Log_print1(Diags_USER1,
"PWM: (%p) unsupported PWM duty mode; duty unchanged",
(UArg) handle);
return;
}
key = Hwi_disable();
/*
* The PWM peripheral cannot generate a duty of 0 when in count down mode
* or a duty equal to period when in count up-down mode. To generate a 0
* duty when in count down mode, the PWM duty is set
* to the period value (output remains active) and output polarity is
* inverted. Additionally, if the output is changed from 0 (to a non-zero
* value) the PWM output polarity must be inverted again.
*
* Likewise, to generate a duty equal to the period when in count up-down
* mode, the PWM duty is set to the period value and the output polarity is
* inverted.
*
* The code below determines if the PWM is in count down or count up-down
* mode and inverts the PWM output polarity if necessary.
* For more details refer to the device specific datasheet and the following
* E2E post:
* http://e2e.ti.com/support/microcontrollers/stellaris_arm/f/471/t/137249.aspx
* http://e2e.ti.com/support/microcontrollers/tiva_arm/f/908/t/354826.aspx
*/
if (HWREG(hwAttrs->baseAddr + pwmGenerator) & PWM_GEN_MODE_UP_DOWN) {
/*
* PWM in count up/down mode - invert output if setting duty to or
* changing from MAX
*/
if ((maxDutySet && object->pwmDuty != period) ||
((!maxDutySet) && object->pwmDuty == period)) {
HWREG(hwAttrs->baseAddr + PWM_O_INVERT) ^= object->pwmOutputBit;
}
}
else {
/*
* PWM in count down mode - invert output if setting duty to or
* changing from 0
*/
if (((!duty) && object->pwmDuty) || (duty && (!object->pwmDuty))) {
HWREG(hwAttrs->baseAddr + PWM_O_INVERT) ^= object->pwmOutputBit;
}
}
object->pwmDuty = (duty) ? newDuty : 0;
PWMPulseWidthSet(hwAttrs->baseAddr, hwAttrs->pwmOutput, newDuty);
Hwi_restore(key);
Log_print2(Diags_USER2, "PWM: (%p) duty set to: %d", (UArg) handle, duty);
}
int main(void)
{
SysCtlClockSet(SYSCTL_SYSDIV_4|SYSCTL_USE_PLL|SYSCTL_XTAL_16MHZ|SYSCTL_OSC_MAIN);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA); // Enable the GPIO A ports
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE); // Enable the GPIO E ports
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOC);
SysCtlPeripheralEnable(SYSCTL_PERIPH_PWM0);
SysCtlPeripheralEnable(SYSCTL_PERIPH_UART4);
GPIOPinConfigure(GPIO_PE4_M0PWM4);
GPIOPinTypePWM(GPIO_PORTE_BASE, GPIO_PIN_4);
GPIOPinConfigure(GPIO_PC4_U4RX);
GPIOPinConfigure(GPIO_PC5_U4TX );
GPIOPinTypeUART(GPIO_PORTC_BASE, GPIO_PIN_4 | GPIO_PIN_5);
GPIOPinConfigure(GPIO_PE5_M0PWM5);
GPIOPinTypePWM(GPIO_PORTE_BASE, GPIO_PIN_5);
PWMGenConfigure(PWM0_BASE, PWM_GEN_2, PWM_GEN_MODE_DOWN | PWM_GEN_MODE_NO_SYNC);
PWMGenPeriodSet(PWM0_BASE, PWM_GEN_2, 6400000);
PWMPulseWidthSet(PWM0_BASE, PWM_OUT_4, PWMGenPeriodGet(PWM0_BASE, PWM_GEN_2) / 1.25);
PWMOutputState(PWM0_BASE, PWM_OUT_4_BIT, true);
PWMGenEnable(PWM0_BASE, PWM_GEN_2);
PWMGenConfigure(PWM0_BASE, PWM_GEN_2, PWM_GEN_MODE_DOWN | PWM_GEN_MODE_NO_SYNC);
PWMGenPeriodSet(PWM0_BASE, PWM_GEN_2, 6400000);
PWMPulseWidthSet(PWM0_BASE, PWM_OUT_5, PWMGenPeriodGet(PWM0_BASE, PWM_GEN_2) / 1.25);
PWMOutputState(PWM0_BASE, PWM_OUT_5_BIT, true);
PWMGenEnable(PWM0_BASE, PWM_GEN_2);
GPIOPinTypeGPIOOutput(GPIO_PORTA_BASE, GPIO_PIN_2|GPIO_PIN_3|GPIO_PIN_6|GPIO_PIN_7);
GPIOPinWrite(GPIO_PORTA_BASE, GPIO_PIN_2|GPIO_PIN_3|GPIO_PIN_6|GPIO_PIN_7,68);
UARTConfigSetExpClk(UART4_BASE, SysCtlClockGet(), 115200, (UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE | UART_CONFIG_PAR_NONE));
UARTEnable(UART4_BASE);
UARTCharPut(UART4_BASE,'a');
while(1)
{
SysCtlDelay(4000000*10);
temp = 1;
UARTSend((uint8_t *)"Fast",4);
PWMPulseWidthSet(PWM0_BASE, PWM_OUT_4, PWMGenPeriodGet(PWM0_BASE, PWM_GEN_2) / 1.25);
PWMPulseWidthSet(PWM0_BASE, PWM_OUT_5, PWMGenPeriodGet(PWM0_BASE, PWM_GEN_2) / 1.25);
SysCtlDelay(4000000*10);
temp = 0;
UARTSend((uint8_t *)"Slow",4);
PWMPulseWidthSet(PWM0_BASE, PWM_OUT_4, PWMGenPeriodGet(PWM0_BASE, PWM_GEN_2) / 3);
PWMPulseWidthSet(PWM0_BASE, PWM_OUT_5, PWMGenPeriodGet(PWM0_BASE, PWM_GEN_2) / 3);
}
}
void servo_parallel(void)
{
uint32_t period = PWMGenPeriodGet(PWM_SERVO_R_BASE, PWM_GEN_SERVO_R);
PWMPulseWidthSet(PWM_SERVO_R_BASE, SERVO_R_OUT, ((DUTY_PARALLEL * period)/100));
PWMPulseWidthSet(PWM_SERVO_L_BASE, SERVO_L_OUT, ((DUTY_PARALLEL * period)/100));
}
void servo_tangent(void)
{
uint32_t period = PWMGenPeriodGet(PWM_SERVO_R_BASE, PWM_GEN_SERVO_R);
PWMPulseWidthSet(PWM_SERVO_R_BASE, SERVO_R_OUT, ((DUTY_TANGENT * period)/100));
PWMPulseWidthSet(PWM_SERVO_L_BASE, SERVO_L_OUT, ((DUTY_TANGENT * period)/100));
}