static void xhci_init(device_t dev)
{
struct soc_intel_baytrail_config *config = dev->chip_info;
struct reg_script xhci_hc_init[] = {
/* Initialize clock gating */
REG_SCRIPT_NEXT(xhci_clock_gating_script),
/* Finalize XHCC1 and XHCC2 */
REG_PCI_RMW32(0x44, ~0x00000000, 0x83c00000),
REG_PCI_RMW32(0x40, ~0x00800000, 0x80000000),
/* Set USB2 Port Routing Mask */
REG_PCI_WRITE32(XHCI_USB2PRM, BYTM_USB2_PORT_MAP),
/* Set USB3 Port Routing Mask */
REG_PCI_WRITE32(XHCI_USB3PRM, BYTM_USB3_PORT_MAP),
/*
* Disable ports if requested
*/
/* Open per-port disable control override */
REG_IO_RMW16(ACPI_BASE_ADDRESS + UPRWC, ~0, UPRWC_WR_EN),
REG_PCI_WRITE32(XHCI_USB2PDO, config->usb2_port_disable_mask),
REG_PCI_WRITE32(XHCI_USB3PDO, config->usb3_port_disable_mask),
/* Close per-port disable control override */
REG_IO_RMW16(ACPI_BASE_ADDRESS + UPRWC, ~UPRWC_WR_EN, 0),
REG_SCRIPT_END
};
/* Initialize XHCI controller for boot or resume path */
if (acpi_is_wakeup_s3())
reg_script_run_on_dev(dev, xhci_init_resume_script);
else
reg_script_run_on_dev(dev, xhci_init_boot_script);
/* C0 steppings change iCLK/USB PLL VCO settings from 5 to 7 */
if (pattrs_get()->stepping == STEP_C0) {
uint32_t reg = iosf_ushphy_read(USHPHY_CDN_PLL_CONTROL);
reg |= 0x00700000;
iosf_ushphy_write(USHPHY_CDN_PLL_CONTROL, reg);
}
/* Finalize Initialization */
reg_script_run_on_dev(dev, xhci_hc_init);
/* Route all ports to XHCI if requested */
if (config->usb_route_to_xhci)
xhci_route_all(dev);
}
static void ehci_init(device_t dev)
{
struct soc_intel_baytrail_config *config = dev->chip_info;
struct reg_script ehci_hc_init[] = {
/* Controller init */
REG_SCRIPT_NEXT(ehci_init_script),
/* Enable clock gating */
REG_SCRIPT_NEXT(ehci_clock_gating_script),
/*
* Disable ports if requested
*/
/* Open per-port disable control override */
REG_IO_RMW16(ACPI_BASE_ADDRESS + UPRWC, ~0, UPRWC_WR_EN),
REG_PCI_WRITE8(EHCI_USB2PDO, config->usb2_port_disable_mask),
/* Close per-port disable control override */
REG_IO_RMW16(ACPI_BASE_ADDRESS + UPRWC, ~UPRWC_WR_EN, 0),
REG_SCRIPT_END
};
/* Don't reset controller in S3 resume path */
if (!acpi_is_wakeup_s3())
reg_script_run_on_dev(dev, ehci_hc_reset);
/* Disable controller if ports are routed to XHCI */
if (config->usb_route_to_xhci) {
/* Disable controller */
reg_script_run_on_dev(dev, ehci_disable_script);
/* Hide device with southcluster function */
dev->enabled = 0;
southcluster_enable_dev(dev);
} else {
/* Initialize EHCI controller */
reg_script_run_on_dev(dev, ehci_hc_init);
}
/* Setup USB2 PHY based on board config */
usb2_phy_init(dev);
}
static void xhci_init(device_t dev)
{
struct soc_intel_baytrail_config *config = dev->chip_info;
struct reg_script xhci_hc_init[] = {
/* Initialize clock gating */
REG_SCRIPT_NEXT(xhci_clock_gating_script),
/* Finalize XHCC1 and XHCC2 */
REG_PCI_RMW32(0x44, ~0x00000000, 0x83c00000),
REG_PCI_RMW32(0x40, ~0x00800000, 0x80000000),
/* Set USB2 Port Routing Mask */
REG_PCI_WRITE32(XHCI_USB2PRM, BYTM_USB2_PORT_MAP),
/* Set USB3 Port Routing Mask */
REG_PCI_WRITE32(XHCI_USB3PRM, BYTM_USB3_PORT_MAP),
/*
* Disable ports if requested
*/
/* Open per-port disable control override */
REG_IO_RMW16(ACPI_BASE_ADDRESS + UPRWC, ~0, UPRWC_WR_EN),
REG_PCI_WRITE32(XHCI_USB2PDO, config->usb2_port_disable_mask),
REG_PCI_WRITE32(XHCI_USB3PDO, config->usb3_port_disable_mask),
/* Close per-port disable control override */
REG_IO_RMW16(ACPI_BASE_ADDRESS + UPRWC, ~UPRWC_WR_EN, 0),
REG_SCRIPT_END
};
/* Initialize XHCI controller for boot or resume path */
if (acpi_slp_type == 3)
reg_script_run_on_dev(dev, xhci_init_resume_script);
else
reg_script_run_on_dev(dev, xhci_init_boot_script);
/* Finalize Initialization */
reg_script_run_on_dev(dev, xhci_hc_init);
/* Route all ports to XHCI if requested */
if (config->usb_route_to_xhci)
xhci_route_all(dev);
}
