//*****************************************************************************
//
// Configure the UART and its pins. This must be called before UARTprintf().
//
//*****************************************************************************
void
ConfigureUART(void)
{
//
// Enable the GPIO Peripheral used by the UART.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOA);
//
// Enable UART0.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UART0);
//
// Configure GPIO Pins for UART mode.
//
ROM_GPIOPinConfigure(GPIO_PA0_U0RX);
ROM_GPIOPinConfigure(GPIO_PA1_U0TX);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Initialize the UART for console I/O.
//
UARTStdioConfig(0, 115200, g_ui32SysClock);
}
//*****************************************************************************
//
// Configure the UART and its pins. This must be called before UARTprintf().
//
//*****************************************************************************
void
ConfigureUART(void)
{
//
// Enable the GPIO Peripheral used by the UART.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
//
// Enable UART0
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UART0);
//
// Configure GPIO Pins for UART mode.
//
ROM_GPIOPinConfigure(GPIO_PA0_U0RX);
ROM_GPIOPinConfigure(GPIO_PA1_U0TX);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// Use the internal 16MHz oscillator as the UART clock source.
//
UARTClockSourceSet(UART0_BASE, UART_CLOCK_PIOSC);
//
// Initialize the UART for console I/O.
//
UARTStdioConfig(0, 115200, 16000000);
}
int cppmain()
{
init();
resetMicros();
enableMessaging();
// Set up the pins
int i;
for (i = 0; i < 12; i++) pinMode(legPins[i], OUTPUT_SERVO);
pinMode(BLUE_LED, OUTPUT);
// We will use WTIMER0 for the interrupts
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_WTIMER0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_WTIMER0);
ROM_TimerConfigure(WTIMER0_BASE, (TIMER_CFG_SPLIT_PAIR | TIMER_CFG_A_PERIODIC | TIMER_CFG_B_PERIODIC));
// Set up the stag walking timer interrupt
ROM_TimerPrescaleSet(WTIMER0_BASE, TIMER_A, 79999); // 1 ms per tick
TimerIntRegister(WTIMER0_BASE, TIMER_A, stagInterrupt);
ROM_TimerLoadSet(WTIMER0_BASE, TIMER_A, 50); // 50 ms per cylce
ROM_TimerIntEnable(WTIMER0_BASE, TIMER_TIMA_TIMEOUT);
ROM_TimerEnable(WTIMER0_BASE, TIMER_A);
ROM_IntPrioritySet(INT_WTIMER0A, 0x20);
// Set general sensor/status interrupt
ROM_TimerPrescaleSet(WTIMER0_BASE, TIMER_B, 79999); // 1 ms per tick
TimerIntRegister(WTIMER0_BASE, TIMER_B, statusInterrupt);
ROM_TimerLoadSet(WTIMER0_BASE, TIMER_B, 500); // 500 ms per cycle
ROM_TimerIntEnable(WTIMER0_BASE, TIMER_TIMB_TIMEOUT);
ROM_TimerEnable(WTIMER0_BASE, TIMER_B);
ROM_IntPrioritySet(INT_WTIMER0A, 0x40);
uint16_t msgLength;
uint16_t msgFlags;
MessageType msgType;
// Main message handing loop
bool z = true;
while (1)
{
digitalWrite(BLUE_LED, z);
z = !z;
switch (getMessage(&msgType, &msgLength, &msgFlags, g_msgBody))
{
case 0: // Success
handleMessage(msgType, msgLength, g_msgBody);
break;
case 1: // Timeout
//sendError(TIMEOUT_ERROR);
break;
case 2: // CRC Error
sendError(CRC_ERROR);
break;
}
//delay(10000);
}
}
void confUART(){
//
// Inicializa la UARTy la configura a 115.200 bps, 8-N-1 .
//se usa para mandar y recibir mensajes y comandos por el puerto serie
// Mediante un programa terminal como gtkterm, putty, cutecom, etc...
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
ROM_GPIOPinConfigure(GPIO_PA0_U0RX);
ROM_GPIOPinConfigure(GPIO_PA1_U0TX);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
UARTStdioConfig(0,115200,SysCtlClockGet());
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UART0); //La UART tiene que seguir funcionando aunque el micro este dormido
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOA); //La UART tiene que seguir funcionando aunque el micro este dormido
}
int main() {
//SysCtlClockSet(SYSCTL_SYSDIV_5|SYSCTL_USE_PLL|SYSCTL_XTAL_16MHZ|SYSCTL_OSC_MAIN);
//Enable Peripherals
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOC);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
//Start specific Pin Ports
GPIOPinTypeGPIOOutput(port_A, GPIO_PIN_2 | GPIO_PIN_3 | GPIO_PIN_4);
GPIOPinTypeGPIOOutput(port_C, GPIO_PIN_4 | GPIO_PIN_5 | GPIO_PIN_6 | GPIO_PIN_7);
GPIOPinTypeGPIOOutput(port_D, GPIO_PIN_6);
GPIOPinTypeGPIOOutput(port_E, GPIO_PIN_0);
GPIOPinTypeGPIOOutput(port_F, GPIO_PIN_4 | GPIO_PIN_1);
//Input Pins
GPIOPinTypeGPIOInput(port_F, GPIO_PIN_2 | GPIO_PIN_3);
//Enable pin for interrupt
GPIOIntEnable(GPIO_PORTF_BASE, (GPIO_INT_PIN_2 | GPIO_INT_PIN_3));
//Set ISR
GPIOIntRegister(GPIO_PORTF_BASE, scroll_button_isr);
//Set interrupt type
GPIOIntTypeSet(GPIO_PORTF_BASE, (GPIO_PIN_2 | GPIO_PIN_3) , GPIO_FALLING_EDGE);
ROM_SysCtlPeripheralSleepDisable(SYSCTL_PERIPH_GPIOA);
ROM_SysCtlPeripheralSleepDisable(SYSCTL_PERIPH_GPIOC);
ROM_SysCtlPeripheralSleepDisable(SYSCTL_PERIPH_GPIOD);
ROM_SysCtlPeripheralSleepDisable(SYSCTL_PERIPH_GPIOE);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOF);
ROM_SysCtlPeripheralClockGating(true);
//Initialize the display
initializeDisplay();
//Write phrases
write_phrases();
}
void enableUART(uint8_t UART, unsigned long baudRate)
{
// We must unlock PD7 to use UART2
if (UART == 2)
{
// GPIO Port D Lock Register is at 0x40007520
HWREG(0x40007520) = GPIO_LOCK_KEY;
// GPIO Port D Control Register is at 0x40007524
HWREG(0x40007524) = 0x80;
}
// Enable the UART peripheral in SysCtl
ROM_SysCtlPeripheralEnable(SysCtlGPIOs[UARTPins[UART][0] / 8]);
ROM_SysCtlPeripheralSleepEnable(SysCtlGPIOs[UARTPins[UART][0] / 8]);
ROM_SysCtlPeripheralEnable(SysCtlUARTs[UART]);
ROM_SysCtlPeripheralSleepEnable(SysCtlUARTs[UART]);
// Configure the associated GPIO pins for UART
ROM_GPIOPinConfigure(UARTPins[UART][2]);
ROM_GPIOPinConfigure(UARTPins[UART][3]);
ROM_GPIOPinTypeUART(GPIO[UARTPins[UART][0] / 8],
bit8[UARTPins[UART][0] % 8] | bit8[UARTPins[UART][1] % 8]);
// Configure the UART
ROM_UARTConfigSetExpClk(UARTBASE[UART], ROM_SysCtlClockGet(), baudRate,
(UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE | UART_CONFIG_PAR_NONE));
ROM_UARTFIFOEnable(UARTBASE[UART]);
// Configure the UART receive (rx) interrupt
ROM_UARTIntEnable(UARTBASE[UART], UART_INT_RX);
UARTFIFOLevelSet(UARTBASE[UART], UART_FIFO_TX4_8, UART_FIFO_RX4_8);
UARTIntRegister(UARTBASE[UART], rxInterrupts[UART]);
ROM_IntPrioritySet(UART_INTs[UART], 0x00);
// Enable the UART
ROM_UARTEnable(UARTBASE[UART]);
}
void enableSPI(unsigned short SPINum, unsigned short wordLength, unsigned long dataRate) {
ROM_SysCtlPeripheralEnable(SysCtlSSI[SPINum]);
ROM_SysCtlPeripheralSleepEnable(SysCtlSSI[SPINum]);
ROM_SysCtlPeripheralEnable(GPIO[ SPIPins[SPINum][0]/8 ]);
int i;
for (i = 0; i < 4; i++){
ROM_GPIOPinTypeSSI(GPIO[ SPIPins[SPINum][i]/8 ], bit8[ SPIPins[SPINum][i]%8 ]);
ROM_GPIOPinConfigure(SPIPins[SPINum][i + 4]);
}
// Polarity 0, Phase 0
ROM_SSIConfigSetExpClk(SSIBase[SPINum], SysCtlClockGet(), 0,
SSI_MODE_MASTER, dataRate, wordLength);
SSIEnable(SSI_BASE);
}
void SSI3DMASlaveClass::configureSSI3() {
//
// Enable the SSI3 Peripheral.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_SSI3);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_SSI3);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOQ);
// Configure GPIO Pins for SSI3 mode.
//
ROM_GPIOPinConfigure(GPIO_PQ0_SSI3CLK);
ROM_GPIOPinConfigure(GPIO_PQ1_SSI3FSS);
ROM_GPIOPinConfigure(GPIO_PQ2_SSI3XDAT0);
ROM_GPIOPinConfigure(GPIO_PQ3_SSI3XDAT1);
ROM_GPIOPinTypeSSI(GPIO_PORTQ_BASE, GPIO_PIN_3 | GPIO_PIN_2 | GPIO_PIN_1 | GPIO_PIN_0);
ROM_SSIConfigSetExpClk(SSI3_BASE, F_CPU, SSI_FRF_MOTO_MODE_0,
SSI_MODE_SLAVE, SPI_CLOCK / 12, 8);
ROM_SSIEnable(SSI3_BASE);
ROM_SSIDMAEnable(SSI3_BASE, SSI_DMA_RX | SSI_DMA_TX);
}
//*****************************************************************************
//
// This example demonstrates how to use the uDMA controller to transfer data
// between memory buffers and to and from a peripheral, in this case a UART.
// The uDMA controller is configured to repeatedly transfer a block of data
// from one memory buffer to another. It is also set up to repeatedly copy a
// block of data from a buffer to the UART output. The UART data is looped
// back so the same data is received, and the uDMA controlled is configured to
// continuously receive the UART data using ping-pong buffers.
//
// The processor is put to sleep when it is not doing anything, and this allows
// collection of CPU usage data to see how much CPU is being used while the
// data transfers are ongoing.
//
//*****************************************************************************
int
main(void)
{
static unsigned long ulPrevSeconds;
static unsigned long ulPrevXferCount;
static unsigned long ulPrevUARTCount = 0;
static char cStrBuf[40];
tRectangle sRect;
unsigned long ulCenterX;
unsigned long ulXfersCompleted;
unsigned long ulBytesTransferred;
//
// Set the clocking to run from the PLL at 50 MHz.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Set the device pinout appropriately for this board.
//
PinoutSet();
//
// Enable peripherals to operate when CPU is in sleep.
//
ROM_SysCtlPeripheralClockGating(true);
//
// Initialize the display driver.
//
Kitronix320x240x16_SSD2119Init();
//
// Initialize the graphics context and find the middle X coordinate.
//
GrContextInit(&g_sContext, &g_sKitronix320x240x16_SSD2119);
//
// Get the center X coordinate of the screen, since it is used a lot.
//
ulCenterX = GrContextDpyWidthGet(&g_sContext) / 2;
//
// Fill the top 15 rows of the screen with blue to create the banner.
//
sRect.sXMin = 0;
sRect.sYMin = 0;
sRect.sXMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.sYMax = 23;
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
GrRectDraw(&g_sContext, &sRect);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, g_pFontCm20);
GrStringDrawCentered(&g_sContext, "udma-demo", -1, ulCenterX, 11, 0);
//
// Show the clock frequency on the display.
//
GrContextFontSet(&g_sContext, g_pFontCmss18b);
usnprintf(cStrBuf, sizeof(cStrBuf), "Stellaris @ %u MHz",
SysCtlClockGet() / 1000000);
GrStringDrawCentered(&g_sContext, cStrBuf, -1, ulCenterX, 40, 0);
//
// Show static text and field labels on the display.
//
GrStringDrawCentered(&g_sContext, "uDMA Mem Transfers", -1,
ulCenterX, 62, 0);
GrStringDrawCentered(&g_sContext, "uDMA UART Transfers", -1,
ulCenterX, 84, 0);
//
// Configure SysTick to occur 100 times per second, to use as a time
// reference. Enable SysTick to generate interrupts.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Initialize the CPU usage measurement routine.
//
CPUUsageInit(SysCtlClockGet(), SYSTICKS_PER_SECOND, 2);
//
// Enable the uDMA controller at the system level. Enable it to continue
// to run while the processor is in sleep.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UDMA);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UDMA);
//
// Enable the uDMA controller error interrupt. This interrupt will occur
// if there is a bus error during a transfer.
//
ROM_IntEnable(INT_UDMAERR);
//
// Enable the uDMA controller.
//
ROM_uDMAEnable();
//
// Point at the control table to use for channel control structures.
//
ROM_uDMAControlBaseSet(ucControlTable);
//
// Initialize the uDMA memory to memory transfers.
//
InitSWTransfer();
//
// Initialize the uDMA UART transfers.
//
InitUART0Transfer();
//
// Remember the current SysTick seconds count.
//
ulPrevSeconds = g_ulSeconds;
//
// Remember the current count of memory buffer transfers.
//
ulPrevXferCount = g_ulMemXferCount;
//
// Loop until the button is pressed. The processor is put to sleep
// in this loop so that CPU utilization can be measured.
//
while(1)
{
//
// Check to see if one second has elapsed. If so, the make some
// updates.
//
if(g_ulSeconds != ulPrevSeconds)
{
//
// Print a message to the display showing the CPU usage percent.
// The fractional part of the percent value is ignored.
//
usnprintf(cStrBuf, sizeof(cStrBuf), "CPU utilization %2u%%",
g_ulCPUUsage >> 16);
GrStringDrawCentered(&g_sContext, cStrBuf, -1, ulCenterX, 160, 1);
//
// Tell the user how many seconds we have to go before ending.
//
usnprintf(cStrBuf, sizeof(cStrBuf), " Test ends in %d seconds ",
10 - g_ulSeconds);
GrStringDrawCentered(&g_sContext, cStrBuf, -1, ulCenterX, 120, 1);
//
// Remember the new seconds count.
//
ulPrevSeconds = g_ulSeconds;
//
// Calculate how many memory transfers have occurred since the last
// second.
//
ulXfersCompleted = g_ulMemXferCount - ulPrevXferCount;
//
// Remember the new transfer count.
//
ulPrevXferCount = g_ulMemXferCount;
//
// Compute how many bytes were transferred in the memory transfer
// since the last second.
//
ulBytesTransferred = ulXfersCompleted * MEM_BUFFER_SIZE * 4;
//
// Print a message to the display showing the memory transfer rate.
//
usnprintf(cStrBuf, sizeof(cStrBuf), " %8u Bytes/Sec ",
ulBytesTransferred);
GrStringDrawCentered(&g_sContext, cStrBuf, -1, ulCenterX, 182, 1);
//
// Calculate how many UART transfers have occurred since the last
// second.
//
ulXfersCompleted = (g_ulRxBufACount + g_ulRxBufBCount -
ulPrevUARTCount);
//
// Remember the new UART transfer count.
//
ulPrevUARTCount = g_ulRxBufACount + g_ulRxBufBCount;
//
// Compute how many bytes were transferred by the UART. The number
// of bytes received is multiplied by 2 so that the TX bytes
// transferred are also accounted for.
//
ulBytesTransferred = ulXfersCompleted * UART_RXBUF_SIZE * 2;
//
// Print a message to the display showing the UART transfer rate.
//
usnprintf(cStrBuf, sizeof(cStrBuf), " %8u Bytes/Sec ",
ulBytesTransferred);
GrStringDrawCentered(&g_sContext, cStrBuf, -1, ulCenterX, 204, 1);
}
//
// Put the processor to sleep if there is nothing to do. This allows
// the CPU usage routine to measure the number of free CPU cycles.
// If the processor is sleeping a lot, it can be hard to connect to
// the target with the debugger.
//
SysCtlSleep();
//
// See if we have run long enough and exit the loop if so.
//
if(g_ulSeconds >= 10)
{
break;
}
}
//*****************************************************************************
//
// Initializes the UART0 peripheral and sets up the TX and RX uDMA channels.
// The UART is configured for loopback mode so that any data sent on TX will be
// received on RX. The uDMA channels are configured so that the TX channel
// will copy data from a buffer to the UART TX output. And the uDMA RX channel
// will receive any incoming data into a pair of buffers in ping-pong mode.
//
//*****************************************************************************
void
InitUART0Transfer(void)
{
unsigned int uIdx;
//
// Fill the TX buffer with a simple data pattern.
//
for(uIdx = 0; uIdx < UART_TXBUF_SIZE; uIdx++)
{
g_ucTxBuf[uIdx] = uIdx;
}
//
// Enable the UART peripheral, and configure it to operate even if the CPU
// is in sleep.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UART0);
//
// Configure the UART communication parameters.
//
ROM_UARTConfigSetExpClk(UART0_BASE, ROM_SysCtlClockGet(), 115200,
UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE |
UART_CONFIG_PAR_NONE);
//
// Set both the TX and RX trigger thresholds to 4. This will be used by
// the uDMA controller to signal when more data should be transferred. The
// uDMA TX and RX channels will be configured so that it can transfer 4
// bytes in a burst when the UART is ready to transfer more data.
//
ROM_UARTFIFOLevelSet(UART0_BASE, UART_FIFO_TX4_8, UART_FIFO_RX4_8);
//
// Enable the UART for operation, and enable the uDMA interface for both TX
// and RX channels.
//
ROM_UARTEnable(UART0_BASE);
ROM_UARTDMAEnable(UART0_BASE, UART_DMA_RX | UART_DMA_TX);
//
// This register write will set the UART to operate in loopback mode. Any
// data sent on the TX output will be received on the RX input.
//
HWREG(UART0_BASE + UART_O_CTL) |= UART_CTL_LBE;
//
// Enable the UART peripheral interrupts. Note that no UART interrupts
// were enabled, but the uDMA controller will cause an interrupt on the
// UART interrupt signal when a uDMA transfer is complete.
//
ROM_IntEnable(INT_UART0);
//
// Put the attributes in a known state for the uDMA UART0RX channel. These
// should already be disabled by default.
//
ROM_uDMAChannelAttributeDisable(UDMA_CHANNEL_UART0RX,
UDMA_ATTR_ALTSELECT | UDMA_ATTR_USEBURST |
UDMA_ATTR_HIGH_PRIORITY |
UDMA_ATTR_REQMASK);
//
// Configure the control parameters for the primary control structure for
// the UART RX channel. The primary contol structure is used for the "A"
// part of the ping-pong receive. The transfer data size is 8 bits, the
// source address does not increment since it will be reading from a
// register. The destination address increment is byte 8-bit bytes. The
// arbitration size is set to 4 to match the RX FIFO trigger threshold.
// The uDMA controller will use a 4 byte burst transfer if possible. This
// will be somewhat more effecient that single byte transfers.
//
ROM_uDMAChannelControlSet(UDMA_CHANNEL_UART0RX | UDMA_PRI_SELECT,
UDMA_SIZE_8 | UDMA_SRC_INC_NONE | UDMA_DST_INC_8 |
UDMA_ARB_4);
//
// Configure the control parameters for the alternate control structure for
// the UART RX channel. The alternate contol structure is used for the "B"
// part of the ping-pong receive. The configuration is identical to the
// primary/A control structure.
//
ROM_uDMAChannelControlSet(UDMA_CHANNEL_UART0RX | UDMA_ALT_SELECT,
UDMA_SIZE_8 | UDMA_SRC_INC_NONE | UDMA_DST_INC_8 |
UDMA_ARB_4);
//
// Set up the transfer parameters for the UART RX primary control
// structure. The mode is set to ping-pong, the transfer source is the
// UART data register, and the destination is the receive "A" buffer. The
// transfer size is set to match the size of the buffer.
//
ROM_uDMAChannelTransferSet(UDMA_CHANNEL_UART0RX | UDMA_PRI_SELECT,
UDMA_MODE_PINGPONG,
(void *)(UART0_BASE + UART_O_DR),
g_ucRxBufA, sizeof(g_ucRxBufA));
//
// Set up the transfer parameters for the UART RX alternate control
// structure. The mode is set to ping-pong, the transfer source is the
// UART data register, and the destination is the receive "B" buffer. The
// transfer size is set to match the size of the buffer.
//
ROM_uDMAChannelTransferSet(UDMA_CHANNEL_UART0RX | UDMA_ALT_SELECT,
UDMA_MODE_PINGPONG,
(void *)(UART0_BASE + UART_O_DR),
g_ucRxBufB, sizeof(g_ucRxBufB));
//
// Put the attributes in a known state for the uDMA UART0TX channel. These
// should already be disabled by default.
//
ROM_uDMAChannelAttributeDisable(UDMA_CHANNEL_UART0TX,
UDMA_ATTR_ALTSELECT |
UDMA_ATTR_HIGH_PRIORITY |
UDMA_ATTR_REQMASK);
//
// Set the USEBURST attribute for the uDMA UART TX channel. This will
// force the controller to always use a burst when transferring data from
// the TX buffer to the UART. This is somewhat more effecient bus usage
// than the default which allows single or burst transfers.
//
ROM_uDMAChannelAttributeEnable(UDMA_CHANNEL_UART0TX, UDMA_ATTR_USEBURST);
//
// Configure the control parameters for the UART TX. The uDMA UART TX
// channel is used to transfer a block of data from a buffer to the UART.
// The data size is 8 bits. The source address increment is 8-bit bytes
// since the data is coming from a buffer. The destination increment is
// none since the data is to be written to the UART data register. The
// arbitration size is set to 4, which matches the UART TX FIFO trigger
// threshold.
//
ROM_uDMAChannelControlSet(UDMA_CHANNEL_UART0TX | UDMA_PRI_SELECT,
UDMA_SIZE_8 | UDMA_SRC_INC_8 | UDMA_DST_INC_NONE |
UDMA_ARB_4);
//
// Set up the transfer parameters for the uDMA UART TX channel. This will
// configure the transfer source and destination and the transfer size.
// Basic mode is used because the peripheral is making the uDMA transfer
// request. The source is the TX buffer and the destination is the UART
// data register.
//
ROM_uDMAChannelTransferSet(UDMA_CHANNEL_UART0TX | UDMA_PRI_SELECT,
UDMA_MODE_BASIC, g_ucTxBuf,
(void *)(UART0_BASE + UART_O_DR),
sizeof(g_ucTxBuf));
//
// Now both the uDMA UART TX and RX channels are primed to start a
// transfer. As soon as the channels are enabled, the peripheral will
// issue a transfer request and the data transfers will begin.
//
ROM_uDMAChannelEnable(UDMA_CHANNEL_UART0RX);
ROM_uDMAChannelEnable(UDMA_CHANNEL_UART0TX);
}
//*****************************************************************************
//
// This example demonstrates how to use the uDMA controller to transfer data
// between memory buffers and to and from a peripheral, in this case a UART.
// The uDMA controller is configured to repeatedly transfer a block of data
// from one memory buffer to another. It is also set up to repeatedly copy a
// block of data from a buffer to the UART output. The UART data is looped
// back so the same data is received, and the uDMA controlled is configured to
// continuously receive the UART data using ping-pong buffers.
//
// The processor is put to sleep when it is not doing anything, and this allows
// collection of CPU usage data to see how much CPU is being used while the
// data transfers are ongoing.
//
//*****************************************************************************
int
main(void)
{
static uint32_t ui32PrevSeconds;
static uint32_t ui32PrevXferCount;
static uint32_t ui32PrevUARTCount = 0;
uint32_t ui32XfersCompleted;
uint32_t ui32BytesTransferred;
//
// Enable lazy stacking for interrupt handlers. This allows floating-point
// instructions to be used within interrupt handlers, but at the expense of
// extra stack usage.
//
ROM_FPULazyStackingEnable();
//
// Set the clocking to run from the PLL at 50 MHz.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Enable peripherals to operate when CPU is in sleep.
//
ROM_SysCtlPeripheralClockGating(true);
//
// Enable the GPIO port that is used for the on-board LED.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
//
// Enable the GPIO pins for the LED (PF2).
//
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_2);
//
// Initialize the UART.
//
ConfigureUART();
UARTprintf("\033[2JuDMA Example\n");
//
// Show the clock frequency on the display.
//
UARTprintf("Tiva C Series @ %u MHz\n\n", ROM_SysCtlClockGet() / 1000000);
//
// Show statistics headings.
//
UARTprintf("CPU Memory UART Remaining\n");
UARTprintf("Usage Transfers Transfers Time\n");
//
// Configure SysTick to occur 100 times per second, to use as a time
// reference. Enable SysTick to generate interrupts.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Initialize the CPU usage measurement routine.
//
CPUUsageInit(ROM_SysCtlClockGet(), SYSTICKS_PER_SECOND, 2);
//
// Enable the uDMA controller at the system level. Enable it to continue
// to run while the processor is in sleep.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UDMA);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UDMA);
//
// Enable the uDMA controller error interrupt. This interrupt will occur
// if there is a bus error during a transfer.
//
ROM_IntEnable(INT_UDMAERR);
//
// Enable the uDMA controller.
//
ROM_uDMAEnable();
//
// Point at the control table to use for channel control structures.
//
ROM_uDMAControlBaseSet(ui8ControlTable);
//
// Initialize the uDMA memory to memory transfers.
//
InitSWTransfer();
//
// Initialize the uDMA UART transfers.
//
InitUART1Transfer();
//
// Remember the current SysTick seconds count.
//
ui32PrevSeconds = g_ui32Seconds;
//
// Remember the current count of memory buffer transfers.
//
ui32PrevXferCount = g_ui32MemXferCount;
//
// Loop until the button is pressed. The processor is put to sleep
// in this loop so that CPU utilization can be measured.
//
while(1)
{
//
// Check to see if one second has elapsed. If so, the make some
// updates.
//
if(g_ui32Seconds != ui32PrevSeconds)
{
//
// Turn on the LED as a heartbeat
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, GPIO_PIN_2);
//
// Print a message to the display showing the CPU usage percent.
// The fractional part of the percent value is ignored.
//
UARTprintf("\r%3d%% ", g_ui32CPUUsage >> 16);
//
// Remember the new seconds count.
//
ui32PrevSeconds = g_ui32Seconds;
//
// Calculate how many memory transfers have occurred since the last
// second.
//
ui32XfersCompleted = g_ui32MemXferCount - ui32PrevXferCount;
//
// Remember the new transfer count.
//
ui32PrevXferCount = g_ui32MemXferCount;
//
// Compute how many bytes were transferred in the memory transfer
// since the last second.
//
ui32BytesTransferred = ui32XfersCompleted * MEM_BUFFER_SIZE * 4;
//
// Print a message showing the memory transfer rate.
//
if(ui32BytesTransferred >= 100000000)
{
UARTprintf("%3d MB/s ", ui32BytesTransferred / 1000000);
}
else if(ui32BytesTransferred >= 10000000)
{
UARTprintf("%2d.%01d MB/s ", ui32BytesTransferred / 1000000,
(ui32BytesTransferred % 1000000) / 100000);
}
else if(ui32BytesTransferred >= 1000000)
{
UARTprintf("%1d.%02d MB/s ", ui32BytesTransferred / 1000000,
(ui32BytesTransferred % 1000000) / 10000);
}
else if(ui32BytesTransferred >= 100000)
{
UARTprintf("%3d KB/s ", ui32BytesTransferred / 1000);
}
else if(ui32BytesTransferred >= 10000)
{
UARTprintf("%2d.%01d KB/s ", ui32BytesTransferred / 1000,
(ui32BytesTransferred % 1000) / 100);
}
else if(ui32BytesTransferred >= 1000)
{
UARTprintf("%1d.%02d KB/s ", ui32BytesTransferred / 1000,
(ui32BytesTransferred % 1000) / 10);
}
else if(ui32BytesTransferred >= 100)
{
UARTprintf("%3d B/s ", ui32BytesTransferred);
}
else if(ui32BytesTransferred >= 10)
{
UARTprintf("%2d B/s ", ui32BytesTransferred);
}
else
{
UARTprintf("%1d B/s ", ui32BytesTransferred);
}
//
// Calculate how many UART transfers have occurred since the last
// second.
//
ui32XfersCompleted = (g_ui32RxBufACount + g_ui32RxBufBCount -
ui32PrevUARTCount);
//
// Remember the new UART transfer count.
//
ui32PrevUARTCount = g_ui32RxBufACount + g_ui32RxBufBCount;
//
// Compute how many bytes were transferred by the UART. The number
// of bytes received is multiplied by 2 so that the TX bytes
// transferred are also accounted for.
//
ui32BytesTransferred = ui32XfersCompleted * UART_RXBUF_SIZE * 2;
//
// Print a message showing the UART transfer rate.
//
if(ui32BytesTransferred >= 1000000)
{
UARTprintf("%1d.%02d MB/s ", ui32BytesTransferred / 1000000,
(ui32BytesTransferred % 1000000) / 10000);
}
else if(ui32BytesTransferred >= 100000)
{
UARTprintf("%3d KB/s ", ui32BytesTransferred / 1000);
}
else if(ui32BytesTransferred >= 10000)
{
UARTprintf("%2d.%01d KB/s ", ui32BytesTransferred / 1000,
(ui32BytesTransferred % 1000) / 100);
}
else if(ui32BytesTransferred >= 1000)
{
UARTprintf("%1d.%02d KB/s ", ui32BytesTransferred / 1000,
(ui32BytesTransferred % 1000) / 10);
}
else if(ui32BytesTransferred >= 100)
{
UARTprintf("%3d B/s ", ui32BytesTransferred);
}
else if(ui32BytesTransferred >= 10)
{
UARTprintf("%2d B/s ", ui32BytesTransferred);
}
else
{
UARTprintf("%1d B/s ", ui32BytesTransferred);
}
//
// Print a spinning line to make it more apparent that there is
// something happening.
//
UARTprintf("%2ds", 10 - ui32PrevSeconds);
//
// Turn off the LED.
//
GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, 0);
}
//
// Put the processor to sleep if there is nothing to do. This allows
// the CPU usage routine to measure the number of free CPU cycles.
// If the processor is sleeping a lot, it can be hard to connect to
// the target with the debugger.
//
ROM_SysCtlSleep();
//
// See if we have run int32_t enough and exit the loop if so.
//
if(g_ui32Seconds >= 10)
{
break;
}
}
//*****************************************************************************
//
// Main 'C' Language entry point.
//
//*****************************************************************************
int
main(void)
{
const uint8_t bufLength=10;
char inputBuf[1];
//
// Configure the system frequency.
//
g_ui32SysClock = MAP_SysCtlClockFreqSet((SYSCTL_XTAL_25MHZ |
SYSCTL_OSC_MAIN | SYSCTL_USE_PLL |
SYSCTL_CFG_VCO_480), 120000000);
//
// Configure the device pins for this board.
//
PinoutSet(false, false);
//
// Initialize the UART.
//
ConfigureUART();
//
// Print the welcome message to the terminal.
//
UARTprintf("\033[2J\033[H");
UARTprintf("SHT21 Example\n");
//
// The I2C7 peripheral must be enabled before use.
//
// Note: For BoosterPack 2 interface use I2C8.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C8);
//ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
//
// Configure the pin muxing for I2C7 functions on port D0 and D1.
// This step is not necessary if your part does not support pin muxing.
//
// Note: For BoosterPack 2 interface use PA2 and PA3.
//
ROM_GPIOPinConfigure(GPIO_PA2_I2C8SCL);
ROM_GPIOPinConfigure(GPIO_PA3_I2C8SDA);
//
// Select the I2C function for these pins. This function will also
// configure the GPIO pins pins for I2C operation, setting them to
// open-drain operation with weak pull-ups. Consult the data sheet
// to see which functions are allocated per pin.
//
// Note: For BoosterPack 2 interface use PA2 and PA3.
//
ROM_GPIOPinTypeI2CSCL(GPIO_PORTA_BASE, GPIO_PIN_2);
ROM_GPIOPinTypeI2C(GPIO_PORTA_BASE, GPIO_PIN_3);
//
// Keep only some parts of the systems running while in sleep mode.
// GPIOE is for the ISL29023 interrupt pin.
// UART0 is the virtual serial port.
// I2C7 is the I2C interface to the ISL29023.
//
// Note: For BoosterPack 2 change this to I2C8.
//
ROM_SysCtlPeripheralClockGating(true);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOE);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UART0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_I2C8);
//
// Enable interrupts to the processor.
//
ROM_IntMasterEnable();
//
// Initialize I2C7 peripheral.
//
// Note: For BoosterPack 2 use I2C8.
//
I2CMInit(&g_sI2CInst, I2C8_BASE, INT_I2C8, 0xff, 0xff, g_ui32SysClock);
//
// Turn on D2 to show we are starting an I2C transaction with the sensor.
// This is turned off in the application callback.
//
LEDWrite(CLP_D1 | CLP_D2 , CLP_D2);
//
// Initialize the SHT21.
//
SHT21Init(&g_sSHT21Inst, &g_sI2CInst, SHT21_I2C_ADDRESS,
SHT21AppCallback, &g_sSHT21Inst);
//
// Initialize the TMP006
//
TMP006Init(&g_sTMP006Inst, &g_sI2CInst, TMP006_I2C_ADDRESS,
TMP006AppCallback, &g_sTMP006Inst);
//
// Wait for the I2C transactions to complete before moving forward.
//
SHT21AppI2CWait(__FILE__, __LINE__);
//
// Delay for 20 milliseconds for SHT21 reset to complete itself.
// Datasheet says reset can take as long 15 milliseconds.
//
ROM_SysCtlDelay(g_ui32SysClock / (50 * 3));
UARTprintf("Menu:\n");
UARTprintf("h for Humidity \n");
UARTprintf("t for Temperature \n");
//
// Loop Forever.
//
while(1)
{
if(UARTgets(inputBuf,bufLength)){
if(inputBuf[0]=='h'){
UARTprintf("Sensing Humidity Data:\n");
printHumidityData();
}
else if(inputBuf[0]=='t'){
UARTprintf("Sensing Temperature Data:\n");
printTemperatureData();
}
}
}
}
//*****************************************************************************
//
// This example application demonstrates the use of the different sleep modes
// and different power configuration options.
//
//*****************************************************************************
int
main(void)
{
//
// Set the clocking to run from the MOSC with the PLL at 16MHz.
//
g_ui32SysClock = MAP_SysCtlClockFreqSet((SYSCTL_XTAL_25MHZ |
SYSCTL_OSC_MAIN |
SYSCTL_USE_PLL |
SYSCTL_CFG_VCO_320), 16000000);
//
// Set the clocking for Deep-Sleep.
// Power down the PIOSC & MOSC to save power and run from the
// internal 30kHz osc.
//
ROM_SysCtlDeepSleepClockConfigSet(1, (SYSCTL_DSLP_OSC_INT30 |
SYSCTL_DSLP_PIOSC_PD | SYSCTL_DSLP_MOSC_PD));
//
// Initialize the UART and write the banner.
// Indicate we are currently in Run Mode.
//
ConfigureUART();
UARTprintf("\033[2J\033[H");
UARTprintf("Sleep Modes example\n\n");
UARTprintf("Mode:\t\tClock Source:\tLED Toggle Source:");
UARTprintf("\nRun\t\tMOSC with PLL\tTimer");
//
// Initialize the buttons driver.
//
ButtonsInit();
//
// Enable the interrupt for the button.
//
ROM_GPIOIntEnable(GPIO_PORTJ_AHB_BASE, GPIO_INT_PIN_0);
//
// Enable the GPIO ports that are used for the on-board LEDs.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPION);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
//
// Set pad config.
//
MAP_GPIOPadConfigSet(GPIO_PORTJ_BASE, GPIO_PIN_0,
GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD_WPU);
//
// Set direction.
//
ROM_GPIODirModeSet(GPIO_PORTJ_BASE, GPIO_PIN_0, GPIO_DIR_MODE_IN);
//
// Enable the interrupt for the button.
//
ROM_GPIOIntEnable(GPIO_PORTJ_BASE, GPIO_INT_PIN_0);
//
// Enable interrupt to NVIC.
//
ROM_IntEnable(INT_GPIOJ);
//
// Enable the GPIO ports that are used for the on-board LEDs.
//
ROM_SysCtlPeripheralEnable(RUN_GPIO_SYSCTL);
ROM_SysCtlPeripheralEnable(SLEEP_GPIO_SYSCTL);
ROM_SysCtlPeripheralEnable(DSLEEP_GPIO_SYSCTL);
ROM_SysCtlPeripheralEnable(TOGGLE_GPIO_SYSCTL);
//
// Enable the GPIO pins for the LED.
//
ROM_GPIOPinTypeGPIOOutput(RUN_GPIO_BASE, RUN_GPIO_PIN);
ROM_GPIOPinTypeGPIOOutput(SLEEP_GPIO_BASE, SLEEP_GPIO_PIN);
ROM_GPIOPinTypeGPIOOutput(DSLEEP_GPIO_BASE, DSLEEP_GPIO_PIN);
ROM_GPIOPinTypeGPIOOutput(TOGGLE_GPIO_BASE, TOGGLE_GPIO_PIN);
//
// Enable the peripherals used by this example.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_TIMER0);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_PWM0);
//
// Enable processor interrupts.
//
ROM_IntMasterEnable();
//
// Configure the 32-bit periodic timer.
//
ROM_TimerConfigure(TIMER0_BASE, TIMER_CFG_PERIODIC);
ROM_TimerLoadSet(TIMER0_BASE, TIMER_A, g_ui32SysClock);
//
// Setup the interrupts for the timer timeout.
//
ROM_IntEnable(INT_TIMER0A);
ROM_TimerIntEnable(TIMER0_BASE, TIMER_TIMA_TIMEOUT);
//
// Configure the PWM0 to count down without synchronization.
// This will be used in Deep-Sleep.
//
ROM_PWMGenConfigure(PWM0_BASE, PWM_GEN_0,
PWM_GEN_MODE_DOWN | PWM_GEN_MODE_NO_SYNC);
//
// Enable the PWM0 output signal.
//
ROM_PWMOutputState(PWM0_BASE, PWM_OUT_0_BIT, true);
//
// Set up the period to match the timer.
//
ROM_PWMGenPeriodSet(PWM0_BASE, PWM_GEN_0, 65000);
//
// Configure the PWM for a 50% duty cycle.
//
ROM_PWMPulseWidthSet(PWM0_BASE, PWM_OUT_0, 65000 >> 1);
//
// Enable the timer.
//
ROM_TimerEnable(TIMER0_BASE, TIMER_A);
//
// Enable the Timer in Sleep Mode.
//
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER0);
//
// Enable the PWM in Deep-Sleep Mode.
//
ROM_SysCtlPeripheralDeepSleepEnable(SYSCTL_PERIPH_PWM0);
//
// Enable the Button Port in Sleep & Deep-Sleep Mode.
//
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOJ);
ROM_SysCtlPeripheralDeepSleepEnable(SYSCTL_PERIPH_GPIOJ);
//
// Enable the LED Ports in Sleep & Deep-Sleep Mode.
//
ROM_SysCtlPeripheralSleepEnable(SLEEP_GPIO_SYSCTL);
ROM_SysCtlPeripheralDeepSleepEnable(DSLEEP_GPIO_SYSCTL);
ROM_SysCtlPeripheralSleepEnable(TOGGLE_GPIO_SYSCTL);
ROM_SysCtlPeripheralDeepSleepEnable(TOGGLE_GPIO_SYSCTL);
//
// Enable Auto Clock Gating Control.
//
ROM_SysCtlPeripheralClockGating(true);
//
// Set LDO to 1.15V in Sleep.
// Set LDO to 1.10V in Deep-Sleep.
//
SysCtlLDOSleepSet(SYSCTL_LDO_1_15V);
SysCtlLDODeepSleepSet(SYSCTL_LDO_1_10V);
//
// Set SRAM to Standby when in Sleep Mode.
// Set Flash & SRAM to Low Power in Deep-Sleep Mode.
//
SysCtlSleepPowerSet(SYSCTL_SRAM_STANDBY);
SysCtlDeepSleepPowerSet(SYSCTL_FLASH_LOW_POWER | SYSCTL_SRAM_LOW_POWER);
//
// Call to set initial LED power state.
//
PowerLEDsSet();
//
// Loop forever.
//
while(1)
{
//
// Handle going into the different sleep modes outside of
// interrupt context.
//
if (g_ui32SleepMode == 1)
{
//
// Go into Sleep Mode.
//
ROM_SysCtlSleep();
}
else if (g_ui32SleepMode == 2)
{
//
// Go into Deep-Sleep Mode.
//
ROM_SysCtlDeepSleep();
}
}
}
//*****************************************************************************
//
// Main application entry point.
//
//*****************************************************************************
int
main(void)
{
int_fast32_t i32IPart[16], i32FPart[16];
uint_fast32_t ui32Idx, ui32CompDCMStarted;
float pfData[16];
float *pfAccel, *pfGyro, *pfMag, *pfEulers, *pfQuaternion;
//
// Initialize convenience pointers that clean up and clarify the code
// meaning. We want all the data in a single contiguous array so that
// we can make our pretty printing easier later.
//
pfAccel = pfData;
pfGyro = pfData + 3;
pfMag = pfData + 6;
pfEulers = pfData + 9;
pfQuaternion = pfData + 12;
//
// Setup the system clock to run at 40 Mhz from PLL with crystal reference
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_5 | SYSCTL_USE_PLL | SYSCTL_XTAL_16MHZ |
SYSCTL_OSC_MAIN);
//
// Enable port B used for motion interrupt.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
//
// Initialize the UART.
//
ConfigureUART();
//
// Print the welcome message to the terminal.
//
UARTprintf("\033[2JMPU9150 Raw Example\n");
//
// Set the color to a purple approximation.
//
g_pui32Colors[RED] = 0x8000;
g_pui32Colors[BLUE] = 0x8000;
g_pui32Colors[GREEN] = 0x0000;
//
// Initialize RGB driver.
//
RGBInit(0);
RGBColorSet(g_pui32Colors);
RGBIntensitySet(0.5f);
RGBEnable();
//
// The I2C3 peripheral must be enabled before use.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C3);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
//
// Configure the pin muxing for I2C3 functions on port D0 and D1.
//
ROM_GPIOPinConfigure(GPIO_PD0_I2C3SCL);
ROM_GPIOPinConfigure(GPIO_PD1_I2C3SDA);
//
// Select the I2C function for these pins. This function will also
// configure the GPIO pins pins for I2C operation, setting them to
// open-drain operation with weak pull-ups. Consult the data sheet
// to see which functions are allocated per pin.
//
GPIOPinTypeI2CSCL(GPIO_PORTD_BASE, GPIO_PIN_0);
ROM_GPIOPinTypeI2C(GPIO_PORTD_BASE, GPIO_PIN_1);
//
// Configure and Enable the GPIO interrupt. Used for INT signal from the
// MPU9150
//
ROM_GPIOPinTypeGPIOInput(GPIO_PORTB_BASE, GPIO_PIN_2);
GPIOIntEnable(GPIO_PORTB_BASE, GPIO_PIN_2);
ROM_GPIOIntTypeSet(GPIO_PORTB_BASE, GPIO_PIN_2, GPIO_FALLING_EDGE);
ROM_IntEnable(INT_GPIOB);
//
// Keep only some parts of the systems running while in sleep mode.
// GPIOB is for the MPU9150 interrupt pin.
// UART0 is the virtual serial port
// TIMER0, TIMER1 and WTIMER5 are used by the RGB driver
// I2C3 is the I2C interface to the ISL29023
//
ROM_SysCtlPeripheralClockGating(true);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UART0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER1);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_I2C3);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_WTIMER5);
//
// Enable interrupts to the processor.
//
ROM_IntMasterEnable();
//
// Initialize I2C3 peripheral.
//
I2CMInit(&g_sI2CInst, I2C3_BASE, INT_I2C3, 0xff, 0xff,
ROM_SysCtlClockGet());
//
// Initialize the MPU9150 Driver.
//
MPU9150Init(&g_sMPU9150Inst, &g_sI2CInst, MPU9150_I2C_ADDRESS,
MPU9150AppCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Write application specifice sensor configuration such as filter settings
// and sensor range settings.
//
g_sMPU9150Inst.pui8Data[0] = MPU9150_CONFIG_DLPF_CFG_94_98;
g_sMPU9150Inst.pui8Data[1] = MPU9150_GYRO_CONFIG_FS_SEL_250;
g_sMPU9150Inst.pui8Data[2] = (MPU9150_ACCEL_CONFIG_ACCEL_HPF_5HZ |
MPU9150_ACCEL_CONFIG_AFS_SEL_2G);
MPU9150Write(&g_sMPU9150Inst, MPU9150_O_CONFIG, g_sMPU9150Inst.pui8Data, 3,
MPU9150AppCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Configure the data ready interrupt pin output of the MPU9150.
//
g_sMPU9150Inst.pui8Data[0] = MPU9150_INT_PIN_CFG_INT_LEVEL |
MPU9150_INT_PIN_CFG_INT_RD_CLEAR |
MPU9150_INT_PIN_CFG_LATCH_INT_EN;
g_sMPU9150Inst.pui8Data[1] = MPU9150_INT_ENABLE_DATA_RDY_EN;
MPU9150Write(&g_sMPU9150Inst, MPU9150_O_INT_PIN_CFG,
g_sMPU9150Inst.pui8Data, 2, MPU9150AppCallback,
&g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Initialize the DCM system. 50 hz sample rate.
// accel weight = .2, gyro weight = .8, mag weight = .2
//
CompDCMInit(&g_sCompDCMInst, 1.0f / 50.0f, 0.2f, 0.6f, 0.2f);
UARTprintf("\033[2J\033[H");
UARTprintf("MPU9150 9-Axis Simple Data Application Example\n\n");
UARTprintf("\033[20GX\033[31G|\033[43GY\033[54G|\033[66GZ\n\n");
UARTprintf("Accel\033[8G|\033[31G|\033[54G|\n\n");
UARTprintf("Gyro\033[8G|\033[31G|\033[54G|\n\n");
UARTprintf("Mag\033[8G|\033[31G|\033[54G|\n\n");
UARTprintf("\n\033[20GRoll\033[31G|\033[43GPitch\033[54G|\033[66GYaw\n\n");
UARTprintf("Eulers\033[8G|\033[31G|\033[54G|\n\n");
UARTprintf("\n\033[17GQ1\033[26G|\033[35GQ2\033[44G|\033[53GQ3\033[62G|"
"\033[71GQ4\n\n");
UARTprintf("Q\033[8G|\033[26G|\033[44G|\033[62G|\n\n");
//
// Enable blinking indicates config finished successfully
//
RGBBlinkRateSet(1.0f);
ui32CompDCMStarted = 0;
while(1)
{
//
// Go to sleep mode while waiting for data ready.
//
while(!g_vui8I2CDoneFlag)
{
ROM_SysCtlSleep();
}
//
// Clear the flag
//
g_vui8I2CDoneFlag = 0;
//
// Get floating point version of the Accel Data in m/s^2.
//
MPU9150DataAccelGetFloat(&g_sMPU9150Inst, pfAccel, pfAccel + 1,
pfAccel + 2);
//
// Get floating point version of angular velocities in rad/sec
//
MPU9150DataGyroGetFloat(&g_sMPU9150Inst, pfGyro, pfGyro + 1,
pfGyro + 2);
//
// Get floating point version of magnetic fields strength in tesla
//
MPU9150DataMagnetoGetFloat(&g_sMPU9150Inst, pfMag, pfMag + 1,
pfMag + 2);
//
// Check if this is our first data ever.
//
if(ui32CompDCMStarted == 0)
{
//
// Set flag indicating that DCM is started.
// Perform the seeding of the DCM with the first data set.
//
ui32CompDCMStarted = 1;
CompDCMMagnetoUpdate(&g_sCompDCMInst, pfMag[0], pfMag[1],
pfMag[2]);
CompDCMAccelUpdate(&g_sCompDCMInst, pfAccel[0], pfAccel[1],
pfAccel[2]);
CompDCMGyroUpdate(&g_sCompDCMInst, pfGyro[0], pfGyro[1],
pfGyro[2]);
CompDCMStart(&g_sCompDCMInst);
}
else
{
//
// DCM Is already started. Perform the incremental update.
//
CompDCMMagnetoUpdate(&g_sCompDCMInst, pfMag[0], pfMag[1],
pfMag[2]);
CompDCMAccelUpdate(&g_sCompDCMInst, pfAccel[0], pfAccel[1],
pfAccel[2]);
CompDCMGyroUpdate(&g_sCompDCMInst, -pfGyro[0], -pfGyro[1],
-pfGyro[2]);
CompDCMUpdate(&g_sCompDCMInst);
}
//
// Increment the skip counter. Skip counter is used so we do not
// overflow the UART with data.
//
g_ui32PrintSkipCounter++;
if(g_ui32PrintSkipCounter >= PRINT_SKIP_COUNT)
{
//
// Reset skip counter.
//
g_ui32PrintSkipCounter = 0;
//
// Get Euler data. (Roll Pitch Yaw)
//
CompDCMComputeEulers(&g_sCompDCMInst, pfEulers, pfEulers + 1,
pfEulers + 2);
//
// Get Quaternions.
//
CompDCMComputeQuaternion(&g_sCompDCMInst, pfQuaternion);
//
// convert mag data to micro-tesla for better human interpretation.
//
pfMag[0] *= 1e6;
pfMag[1] *= 1e6;
pfMag[2] *= 1e6;
//
// Convert Eulers to degrees. 180/PI = 57.29...
// Convert Yaw to 0 to 360 to approximate compass headings.
//
pfEulers[0] *= 57.295779513082320876798154814105f;
pfEulers[1] *= 57.295779513082320876798154814105f;
pfEulers[2] *= 57.295779513082320876798154814105f;
if(pfEulers[2] < 0)
{
pfEulers[2] += 360.0f;
}
//
// Now drop back to using the data as a single array for the
// purpose of decomposing the float into a integer part and a
// fraction (decimal) part.
//
for(ui32Idx = 0; ui32Idx < 16; ui32Idx++)
{
//
// Conver float value to a integer truncating the decimal part.
//
i32IPart[ui32Idx] = (int32_t) pfData[ui32Idx];
//
// Multiply by 1000 to preserve first three decimal values.
// Truncates at the 3rd decimal place.
//
i32FPart[ui32Idx] = (int32_t) (pfData[ui32Idx] * 1000.0f);
//
// Subtract off the integer part from this newly formed decimal
// part.
//
i32FPart[ui32Idx] = i32FPart[ui32Idx] -
(i32IPart[ui32Idx] * 1000);
//
// make the decimal part a positive number for display.
//
if(i32FPart[ui32Idx] < 0)
{
i32FPart[ui32Idx] *= -1;
}
}
//
// Print the acceleration numbers in the table.
//
UARTprintf("\033[5;17H%3d.%03d", i32IPart[0], i32FPart[0]);
UARTprintf("\033[5;40H%3d.%03d", i32IPart[1], i32FPart[1]);
UARTprintf("\033[5;63H%3d.%03d", i32IPart[2], i32FPart[2]);
//
// Print the angular velocities in the table.
//
UARTprintf("\033[7;17H%3d.%03d", i32IPart[3], i32FPart[3]);
UARTprintf("\033[7;40H%3d.%03d", i32IPart[4], i32FPart[4]);
UARTprintf("\033[7;63H%3d.%03d", i32IPart[5], i32FPart[5]);
//
// Print the magnetic data in the table.
//
UARTprintf("\033[9;17H%3d.%03d", i32IPart[6], i32FPart[6]);
UARTprintf("\033[9;40H%3d.%03d", i32IPart[7], i32FPart[7]);
UARTprintf("\033[9;63H%3d.%03d", i32IPart[8], i32FPart[8]);
//
// Print the Eulers in a table.
//
UARTprintf("\033[14;17H%3d.%03d", i32IPart[9], i32FPart[9]);
UARTprintf("\033[14;40H%3d.%03d", i32IPart[10], i32FPart[10]);
UARTprintf("\033[14;63H%3d.%03d", i32IPart[11], i32FPart[11]);
//
// Print the quaternions in a table format.
//
UARTprintf("\033[19;14H%3d.%03d", i32IPart[12], i32FPart[12]);
UARTprintf("\033[19;32H%3d.%03d", i32IPart[13], i32FPart[13]);
UARTprintf("\033[19;50H%3d.%03d", i32IPart[14], i32FPart[14]);
UARTprintf("\033[19;68H%3d.%03d", i32IPart[15], i32FPart[15]);
}
}
}
//*****************************************************************************
//
// MPU9150 I2C pheripheral set up and sensor/compdcm initialization.
//
// Created by Bill Yiqiu Wang 2015/7/27
//
//*****************************************************************************
void
MPU9150Config(void *pvCallbackData, uint_fast8_t ui8Status)
{
//
// Enable port B used for motion interrupt.
// Enable port E used for I2C communication
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
//
// The I2C2 peripheral must be enabled before use.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C2);
//
// Configure the pin muxing for I2C2 functions on port D0 and D1.
//
ROM_GPIOPinConfigure(GPIO_PE4_I2C2SCL);
ROM_GPIOPinConfigure(GPIO_PE5_I2C2SDA);
//
// Select the I2C function for these pins. This function will also
// configure the GPIO pins pins for I2C operation, setting them to
// open-drain operation with weak pull-ups. Consult the data sheet
// to see which functions are allocated per pin.
//
GPIOPinTypeI2CSCL(GPIO_PORTE_BASE, GPIO_PIN_4);
ROM_GPIOPinTypeI2C(GPIO_PORTE_BASE, GPIO_PIN_5);
//
// Configure and Enable the GPIO interrupt. Used for INT signal from the
// MPU9150
//
ROM_GPIOPinTypeGPIOInput(GPIO_PORTB_BASE, GPIO_PIN_2);
GPIOIntEnable(GPIO_PORTB_BASE, GPIO_PIN_2);
ROM_GPIOIntTypeSet(GPIO_PORTB_BASE, GPIO_PIN_2, GPIO_FALLING_EDGE);
ROM_IntEnable(INT_GPIOB);
//
// Keep the following function running even when system is sleeping (optional)
// GPIOB is for the MPU9150 interrupt pin.
// GPIOE is for I2C pin.
// I2C2 is the I2C interface
// TIMER0, TIMER1 and WTIMER5 are used by the RGB driver
//
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOE);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_I2C2);
ROM_SysCtlPeripheralClockGating(true);
//
// Initialize I2C2 peripheral.
//
I2CMInit(&g_sI2CInst, I2C2_BASE, INT_I2C2, 0xff, 0xff,
ROM_SysCtlClockGet());
//
// Initialize the MPU9150 Driver.
//
MPU9150Init(&g_sMPU9150Inst, &g_sI2CInst, MPU9150_I2C_ADDRESS,
MPU9150AppCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Write application specifice sensor configuration such as filter settings
// and sensor range settings.
//
g_sMPU9150Inst.pui8Data[0] = MPU9150_CONFIG_DLPF_CFG_94_98;
g_sMPU9150Inst.pui8Data[1] = MPU9150_GYRO_CONFIG_FS_SEL_250;
g_sMPU9150Inst.pui8Data[2] = (MPU9150_ACCEL_CONFIG_ACCEL_HPF_5HZ |
MPU9150_ACCEL_CONFIG_AFS_SEL_2G);
MPU9150Write(&g_sMPU9150Inst, MPU9150_O_CONFIG, g_sMPU9150Inst.pui8Data, 3,
MPU9150AppCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Configure the data ready interrupt pin output of the MPU9150.
//
g_sMPU9150Inst.pui8Data[0] = MPU9150_INT_PIN_CFG_INT_LEVEL |
MPU9150_INT_PIN_CFG_INT_RD_CLEAR |
MPU9150_INT_PIN_CFG_LATCH_INT_EN;
g_sMPU9150Inst.pui8Data[1] = MPU9150_INT_ENABLE_DATA_RDY_EN;
MPU9150Write(&g_sMPU9150Inst, MPU9150_O_INT_PIN_CFG,
g_sMPU9150Inst.pui8Data, 2, MPU9150AppCallback,
&g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Initialize the DCM system. 50 hz sample rate.
// accel weight = .2, gyro weight = .8, mag weight = .2
//
CompDCMInit(&g_sCompDCMInst, 1.0f / 50.0f, 0.2f, 0.6f, 0.2f);
}
//*****************************************************************************
//
// This example demonstrates how to use the uDMA controller to transfer data
// between memory buffers and to and from a peripheral, in this case a UART.
// The uDMA controller is configured to repeatedly transfer a block of data
// from one memory buffer to another. It is also set up to repeatedly copy a
// block of data from a buffer to the UART output. The UART data is looped
// back so the same data is received, and the uDMA controlled is configured to
// continuously receive the UART data using ping-pong buffers.
//
// The processor is put to sleep when it is not doing anything, and this allows
// collection of CPU usage data to see how much CPU is being used while the
// data transfers are ongoing.
//
//*****************************************************************************
int
main(void)
{
static unsigned long ulPrevSeconds;
static unsigned long ulPrevXferCount;
static unsigned long ulPrevUARTCount = 0;
unsigned long ulXfersCompleted;
unsigned long ulBytesTransferred;
unsigned long ulButton;
//
// Set the clocking to run from the PLL at 50 MHz.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Enable peripherals to operate when CPU is in sleep.
//
ROM_SysCtlPeripheralClockGating(true);
//
// Set the push button as an input with a pull-up.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_GPIODirModeSet(GPIO_PORTB_BASE, GPIO_PIN_4, GPIO_DIR_MODE_IN);
ROM_GPIOPadConfigSet(GPIO_PORTB_BASE, GPIO_PIN_4,
GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD_WPU);
//
// Initialize the UART.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UART0);
GPIOPinConfigure(GPIO_PA0_U0RX);
GPIOPinConfigure(GPIO_PA1_U0TX);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
UARTStdioInit(0);
UARTprintf("\033[2JuDMA Example\n");
//
// Show the clock frequency and exit instructions.
//
UARTprintf("Stellaris @ %u MHz\n", ROM_SysCtlClockGet() / 1000000);
UARTprintf("Press button to use debugger.\n\n");
//
// Show statistics headings.
//
UARTprintf("CPU Memory UART\n");
UARTprintf("Usage Transfers Transfers\n");
//
// Configure SysTick to occur 100 times per second, to use as a time
// reference. Enable SysTick to generate interrupts.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Initialize the CPU usage measurement routine.
//
CPUUsageInit(ROM_SysCtlClockGet(), SYSTICKS_PER_SECOND, 2);
//
// Enable the uDMA controller at the system level. Enable it to continue
// to run while the processor is in sleep.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UDMA);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UDMA);
//
// Enable the uDMA controller error interrupt. This interrupt will occur
// if there is a bus error during a transfer.
//
ROM_IntEnable(INT_UDMAERR);
//
// Enable the uDMA controller.
//
ROM_uDMAEnable();
//
// Point at the control table to use for channel control structures.
//
ROM_uDMAControlBaseSet(ucControlTable);
//
// Initialize the uDMA memory to memory transfers.
//
InitSWTransfer();
//
// Initialize the uDMA UART transfers.
//
InitUART1Transfer();
//
// Remember the current SysTick seconds count.
//
ulPrevSeconds = g_ulSeconds;
//
// Remember the current count of memory buffer transfers.
//
ulPrevXferCount = g_ulMemXferCount;
//
// Loop until the button is pressed. The processor is put to sleep
// in this loop so that CPU utilization can be measured. When the
// processor is sleeping a lot, it can be hard to connect to the target
// with the debugger. Pressing the button will cause this loop to exit
// and the processor will no longer sleep.
//
while(1)
{
//
// Check for the select button press. If the button is pressed,
// then exit this loop.
//
ulButton = ROM_GPIOPinRead(GPIO_PORTB_BASE, GPIO_PIN_4);
if(!ulButton)
{
break;
}
//
// Check to see if one second has elapsed. If so, the make some
// updates.
//
if(g_ulSeconds != ulPrevSeconds)
{
//
// Print a message to the display showing the CPU usage percent.
// The fractional part of the percent value is ignored.
//
UARTprintf("\r%3d%% ", g_ulCPUUsage >> 16);
//
// Remember the new seconds count.
//
ulPrevSeconds = g_ulSeconds;
//
// Calculate how many memory transfers have occurred since the last
// second.
//
ulXfersCompleted = g_ulMemXferCount - ulPrevXferCount;
//
// Remember the new transfer count.
//
ulPrevXferCount = g_ulMemXferCount;
//
// Compute how many bytes were transferred in the memory transfer
// since the last second.
//
ulBytesTransferred = ulXfersCompleted * MEM_BUFFER_SIZE * 4;
//
// Print a message showing the memory transfer rate.
//
if(ulBytesTransferred >= 100000000)
{
UARTprintf("%3d MB/s ", ulBytesTransferred / 1000000);
}
else if(ulBytesTransferred >= 10000000)
{
UARTprintf("%2d.%01d MB/s ", ulBytesTransferred / 1000000,
(ulBytesTransferred % 1000000) / 100000);
}
else if(ulBytesTransferred >= 1000000)
{
UARTprintf("%1d.%02d MB/s ", ulBytesTransferred / 1000000,
(ulBytesTransferred % 1000000) / 10000);
}
else if(ulBytesTransferred >= 100000)
{
UARTprintf("%3d KB/s ", ulBytesTransferred / 1000);
}
else if(ulBytesTransferred >= 10000)
{
UARTprintf("%2d.%01d KB/s ", ulBytesTransferred / 1000,
(ulBytesTransferred % 1000) / 100);
}
else if(ulBytesTransferred >= 1000)
{
UARTprintf("%1d.%02d KB/s ", ulBytesTransferred / 1000,
(ulBytesTransferred % 1000) / 10);
}
else if(ulBytesTransferred >= 100)
{
UARTprintf("%3d B/s ", ulBytesTransferred);
}
else if(ulBytesTransferred >= 10)
{
UARTprintf("%2d B/s ", ulBytesTransferred);
}
else
{
UARTprintf("%1d B/s ", ulBytesTransferred);
}
//
// Calculate how many UART transfers have occurred since the last
// second.
//
ulXfersCompleted = (g_ulRxBufACount + g_ulRxBufBCount -
ulPrevUARTCount);
//
// Remember the new UART transfer count.
//
ulPrevUARTCount = g_ulRxBufACount + g_ulRxBufBCount;
//
// Compute how many bytes were transferred by the UART. The number
// of bytes received is multiplied by 2 so that the TX bytes
// transferred are also accounted for.
//
ulBytesTransferred = ulXfersCompleted * UART_RXBUF_SIZE * 2;
//
// Print a message showing the UART transfer rate.
//
if(ulBytesTransferred >= 1000000)
{
UARTprintf("%1d.%02d MB/s ", ulBytesTransferred / 1000000,
(ulBytesTransferred % 1000000) / 10000);
}
else if(ulBytesTransferred >= 100000)
{
UARTprintf("%3d KB/s ", ulBytesTransferred / 1000);
}
else if(ulBytesTransferred >= 10000)
{
UARTprintf("%2d.%01d KB/s ", ulBytesTransferred / 1000,
(ulBytesTransferred % 1000) / 100);
}
else if(ulBytesTransferred >= 1000)
{
UARTprintf("%1d.%02d KB/s ", ulBytesTransferred / 1000,
(ulBytesTransferred % 1000) / 10);
}
else if(ulBytesTransferred >= 100)
{
UARTprintf("%3d B/s ", ulBytesTransferred);
}
else if(ulBytesTransferred >= 10)
{
UARTprintf("%2d B/s ", ulBytesTransferred);
}
else
{
UARTprintf("%1d B/s ", ulBytesTransferred);
}
//
// Print a spinning line to make it more apparent that there is
// something happening.
//
UARTprintf("%c", g_pcTwirl[ulPrevSeconds % 4]);
}
//
// Put the processor to sleep if there is nothing to do. This allows
// the CPU usage routine to measure the number of free CPU cycles.
// If the processor is sleeping a lot, it can be hard to connect to
// the target with the debugger.
//
ROM_SysCtlSleep();
}
//*****************************************************************************
//
// Main 'C' Language entry point.
//
//*****************************************************************************
int
main(void)
{
float fAmbient;
int32_t i32IntegerPart, i32FractionPart;
uint8_t ui8Mask;
//
// Setup the system clock to run at 40 Mhz from PLL with crystal reference
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_5 | SYSCTL_USE_PLL | SYSCTL_XTAL_16MHZ |
SYSCTL_OSC_MAIN);
//
// Enable the peripherals used by this example.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
//
// Initialize the UART and its pins.
//
ConfigureUART();
//
// Print the welcome message to the terminal.
//
UARTprintf("\033[2JISL29023 Example\n");
//
// Set the color to a white approximation.
//
g_pui32Colors[RED] = 0x8000;
g_pui32Colors[BLUE] = 0x8000;
g_pui32Colors[GREEN] = 0x8000;
//
// Initialize RGB driver. Use a default intensity and blink rate.
//
RGBInit(0);
RGBColorSet(g_pui32Colors);
RGBIntensitySet(0.5f);
RGBEnable();
//
// The I2C3 peripheral must be enabled before use.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C3);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
//
// Configure the pin muxing for I2C3 functions on port D0 and D1.
// This step is not necessary if your part does not support pin muxing.
//
ROM_GPIOPinConfigure(GPIO_PD0_I2C3SCL);
ROM_GPIOPinConfigure(GPIO_PD1_I2C3SDA);
//
// Select the I2C function for these pins. This function will also
// configure the GPIO pins pins for I2C operation, setting them to
// open-drain operation with weak pull-ups. Consult the data sheet
// to see which functions are allocated per pin.
//
GPIOPinTypeI2CSCL(GPIO_PORTD_BASE, GPIO_PIN_0);
ROM_GPIOPinTypeI2C(GPIO_PORTD_BASE, GPIO_PIN_1);
//
// Configure and Enable the GPIO interrupt. Used for INT signal from the
// ISL29023
//
ROM_GPIOPinTypeGPIOInput(GPIO_PORTE_BASE, GPIO_PIN_5);
GPIOIntEnable(GPIO_PORTE_BASE, GPIO_PIN_5);
ROM_GPIOIntTypeSet(GPIO_PORTE_BASE, GPIO_PIN_5, GPIO_FALLING_EDGE);
ROM_IntEnable(INT_GPIOE);
//
// Keep only some parts of the systems running while in sleep mode.
// GPIOE is for the ISL29023 interrupt pin.
// UART0 is the virtual serial port
// TIMER0, TIMER1 and WTIMER5 are used by the RGB driver
// I2C3 is the I2C interface to the ISL29023
//
ROM_SysCtlPeripheralClockGating(true);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOE);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UART0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER1);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_I2C3);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_WTIMER5);
//
// Configure desired interrupt priorities. Setting the I2C interrupt to be
// of more priority than SysTick and the GPIO interrupt means those
// interrupt routines can use the I2CM_DRV Application context does not use
// I2CM_DRV API and GPIO and SysTick are at the same priority level. This
// prevents re-entrancy problems with I2CM_DRV but keeps the MCU in sleep
// state as much as possible. UART is at least priority so it can operate
// in the background.
//
ROM_IntPrioritySet(INT_I2C3, 0x00);
ROM_IntPrioritySet(FAULT_SYSTICK, 0x40);
ROM_IntPrioritySet(INT_GPIOE, 0x80);
ROM_IntPrioritySet(INT_UART0, 0x80);
//
// Enable interrupts to the processor.
//
ROM_IntMasterEnable();
//
// Initialize I2C3 peripheral.
//
I2CMInit(&g_sI2CInst, I2C3_BASE, INT_I2C3, 0xff, 0xff,
ROM_SysCtlClockGet());
//
// Initialize the ISL29023 Driver.
//
ISL29023Init(&g_sISL29023Inst, &g_sI2CInst, ISL29023_I2C_ADDRESS,
ISL29023AppCallback, &g_sISL29023Inst);
//
// Wait for transaction to complete
//
ISL29023AppI2CWait(__FILE__, __LINE__);
//
// Configure the ISL29023 to measure ambient light continuously. Set a 8
// sample persistence before the INT pin is asserted. Clears the INT flag.
// Persistence setting of 8 is sufficient to ignore camera flashes.
//
ui8Mask = (ISL29023_CMD_I_OP_MODE_M | ISL29023_CMD_I_INT_PERSIST_M |
ISL29023_CMD_I_INT_FLAG_M);
ISL29023ReadModifyWrite(&g_sISL29023Inst, ISL29023_O_CMD_I, ~ui8Mask,
(ISL29023_CMD_I_OP_MODE_ALS_CONT |
ISL29023_CMD_I_INT_PERSIST_8),
ISL29023AppCallback, &g_sISL29023Inst);
//
// Wait for transaction to complete
//
ISL29023AppI2CWait(__FILE__, __LINE__);
//
// Configure the upper threshold to 80% of maximum value
//
g_sISL29023Inst.pui8Data[1] = 0xCC;
g_sISL29023Inst.pui8Data[2] = 0xCC;
ISL29023Write(&g_sISL29023Inst, ISL29023_O_INT_HT_LSB,
g_sISL29023Inst.pui8Data, 2, ISL29023AppCallback,
&g_sISL29023Inst);
//
// Wait for transaction to complete
//
ISL29023AppI2CWait(__FILE__, __LINE__);
//
// Configure the lower threshold to 20% of maximum value
//
g_sISL29023Inst.pui8Data[1] = 0x33;
g_sISL29023Inst.pui8Data[2] = 0x33;
ISL29023Write(&g_sISL29023Inst, ISL29023_O_INT_LT_LSB,
g_sISL29023Inst.pui8Data, 2, ISL29023AppCallback,
&g_sISL29023Inst);
//
// Wait for transaction to complete
//
ISL29023AppI2CWait(__FILE__, __LINE__);
//
//Configure and enable SysTick Timer
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// After all the init and config we start blink the LED
//
RGBBlinkRateSet(1.0f);
//
// Loop Forever
//
while(1)
{
ROM_SysCtlSleep();
if(g_vui8DataFlag)
{
g_vui8DataFlag = 0;
//
// Get a local floating point copy of the latest light data
//
ISL29023DataLightVisibleGetFloat(&g_sISL29023Inst, &fAmbient);
//
// Perform the conversion from float to a printable set of integers
//
i32IntegerPart = (int32_t)fAmbient;
i32FractionPart = (int32_t)(fAmbient * 1000.0f);
i32FractionPart = i32FractionPart - (i32IntegerPart * 1000);
if(i32FractionPart < 0)
{
i32FractionPart *= -1;
}
//
// Print the temperature as integer and fraction parts.
//
UARTprintf("Visible Lux: %3d.%03d\n", i32IntegerPart,
i32FractionPart);
//
// Check if the intensity of light has crossed a threshold. If so
// then adjust range of sensor readings to track intensity.
//
if(g_vui8IntensityFlag)
{
//
// Disable the low priority interrupts leaving only the I2C
// interrupt enabled.
//
ROM_IntPriorityMaskSet(0x40);
//
// Reset the intensity trigger flag.
//
g_vui8IntensityFlag = 0;
//
// Adjust the lux range.
//
ISL29023AppAdjustRange(&g_sISL29023Inst);
//
// Now we must manually clear the flag in the ISL29023
// register.
//
ISL29023Read(&g_sISL29023Inst, ISL29023_O_CMD_I,
g_sISL29023Inst.pui8Data, 1, ISL29023AppCallback,
&g_sISL29023Inst);
//
// Wait for transaction to complete
//
ISL29023AppI2CWait(__FILE__, __LINE__);
//
// Disable priority masking so all interrupts are enabled.
//
ROM_IntPriorityMaskSet(0);
}
}
}
}
//*****************************************************************************
//
// Main 'C' Language entry point.
//
//*****************************************************************************
int
main(void)
{
float fAmbient, fObject;
int_fast32_t i32IntegerPart;
int_fast32_t i32FractionPart;
//
// Setup the system clock to run at 40 Mhz from PLL with crystal reference
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_5 | SYSCTL_USE_PLL | SYSCTL_XTAL_16MHZ |
SYSCTL_OSC_MAIN);
//
// Enable the peripherals used by this example.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
//
// Initialize the UART.
//
ConfigureUART();
//
// Print the welcome message to the terminal.
//
UARTprintf("\033[2J\033[1;1HTMP006 Example\n");
//
// Setup the color of the RGB LED.
//
g_pui32Colors[RED] = 0;
g_pui32Colors[BLUE] = 0xFFFF;
g_pui32Colors[GREEN] = 0;
//
// Initialize the RGB Driver and start RGB blink operation.
//
RGBInit(0);
RGBColorSet(g_pui32Colors);
RGBIntensitySet(0.5f);
RGBEnable();
//
// The I2C3 peripheral must be enabled before use.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C3);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
//
// Configure the pin muxing for I2C3 functions on port D0 and D1.
// This step is not necessary if your part does not support pin muxing.
//
ROM_GPIOPinConfigure(GPIO_PD0_I2C3SCL);
ROM_GPIOPinConfigure(GPIO_PD1_I2C3SDA);
//
// Select the I2C function for these pins. This function will also
// configure the GPIO pins pins for I2C operation, setting them to
// open-drain operation with weak pull-ups. Consult the data sheet
// to see which functions are allocated per pin.
//
GPIOPinTypeI2CSCL(GPIO_PORTD_BASE, GPIO_PIN_0);
ROM_GPIOPinTypeI2C(GPIO_PORTD_BASE, GPIO_PIN_1);
//
// Configure and Enable the GPIO interrupt. Used for DRDY from the TMP006
//
ROM_GPIOPinTypeGPIOInput(GPIO_PORTE_BASE, GPIO_PIN_0);
GPIOIntEnable(GPIO_PORTE_BASE, GPIO_PIN_0);
ROM_GPIOIntTypeSet(GPIO_PORTE_BASE, GPIO_PIN_0, GPIO_FALLING_EDGE);
ROM_IntEnable(INT_GPIOE);
//
// Keep only some parts of the systems running while in sleep mode.
// GPIOE is for the TMP006 data ready interrupt.
// UART0 is the virtual serial port
// TIMER0, TIMER1 and WTIMER5 are used by the RGB driver
// I2C3 is the I2C interface to the TMP006
//
ROM_SysCtlPeripheralClockGating(true);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOE);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UART0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER1);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_I2C3);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_WTIMER5);
//
// Enable interrupts to the processor.
//
ROM_IntMasterEnable();
//
// Initialize I2C3 peripheral.
//
I2CMInit(&g_sI2CInst, I2C3_BASE, INT_I2C3, 0xff, 0xff,
SysCtlClockGet());
//
// Initialize the TMP006
//
TMP006Init(&g_sTMP006Inst, &g_sI2CInst, TMP006_I2C_ADDRESS,
TMP006AppCallback, &g_sTMP006Inst);
//
// Put the processor to sleep while we wait for the I2C driver to
// indicate that the transaction is complete.
//
while((g_vui8DataFlag == 0) && (g_vui8ErrorFlag == 0))
{
ROM_SysCtlSleep();
}
//
// If an error occurred call the error handler immediately.
//
if(g_vui8ErrorFlag)
{
TMP006AppErrorHandler(__FILE__, __LINE__);
}
//
// clear the data flag for next use.
//
g_vui8DataFlag = 0;
//
// Delay for 10 milliseconds for TMP006 reset to complete.
// Not explicitly required. Datasheet does not say how long a reset takes.
//
ROM_SysCtlDelay(ROM_SysCtlClockGet() / (100 * 3));
//
// Enable the DRDY pin indication that a conversion is in progress.
//
TMP006ReadModifyWrite(&g_sTMP006Inst, TMP006_O_CONFIG,
~TMP006_CONFIG_EN_DRDY_PIN_M,
TMP006_CONFIG_EN_DRDY_PIN, TMP006AppCallback,
&g_sTMP006Inst);
//
// Wait for the DRDY enable I2C transaction to complete.
//
while((g_vui8DataFlag == 0) && (g_vui8ErrorFlag == 0))
{
ROM_SysCtlSleep();
}
//
// If an error occurred call the error handler immediately.
//
if(g_vui8ErrorFlag)
{
TMP006AppErrorHandler(__FILE__, __LINE__);
}
//
// clear the data flag for next use.
//
g_vui8DataFlag = 0;
//
// Last thing before the loop start blinking to show we got this far and
// the tmp006 is setup and ready for auto measure
//
RGBBlinkRateSet(1.0f);
//
// Loop Forever
//
while(1)
{
//
// Put the processor to sleep while we wait for the TMP006 to
// signal that data is ready. Also continue to sleep while I2C
// transactions get the raw data from the TMP006
//
while((g_vui8DataFlag == 0) && (g_vui8ErrorFlag == 0))
{
ROM_SysCtlSleep();
}
//
// If an error occurred call the error handler immediately.
//
if(g_vui8ErrorFlag)
{
TMP006AppErrorHandler(__FILE__, __LINE__);
}
//
// Reset the flag
//
g_vui8DataFlag = 0;
//
// Get a local copy of the latest data in float format.
//
TMP006DataTemperatureGetFloat(&g_sTMP006Inst, &fAmbient, &fObject);
//
// Convert the floating point ambient temperature to an integer part
// and fraction part for easy printing.
//
i32IntegerPart = (int32_t)fAmbient;
i32FractionPart = (int32_t)(fAmbient * 1000.0f);
i32FractionPart = i32FractionPart - (i32IntegerPart * 1000);
if(i32FractionPart < 0)
{
i32FractionPart *= -1;
}
UARTprintf("Ambient %3d.%03d\t", i32IntegerPart, i32FractionPart);
//
// Convert the floating point ambient temperature to an integer part
// and fraction part for easy printing.
//
i32IntegerPart = (int32_t)fObject;
i32FractionPart = (int32_t)(fObject * 1000.0f);
i32FractionPart = i32FractionPart - (i32IntegerPart * 1000);
if(i32FractionPart < 0)
{
i32FractionPart *= -1;
}
UARTprintf("Object %3d.%03d\n", i32IntegerPart, i32FractionPart);
}
}
//*****************************************************************************
//
// Main application entry point.
//
//*****************************************************************************
int main(void) {
int_fast32_t i32IPart[17], i32FPart[17];
uint_fast32_t ui32Idx, ui32CompDCMStarted;
float pfData[17];
float *pfAccel, *pfGyro, *pfMag, *pfEulers, *pfQuaternion;
float *direction;
//
// Initialize convenience pointers that clean up and clarify the code
// meaning. We want all the data in a single contiguous array so that
// we can make our pretty printing easier later.
//
pfAccel = pfData;
pfGyro = pfData + 3;
pfMag = pfData + 6;
pfEulers = pfData + 9;
pfQuaternion = pfData + 12;
direction = pfData + 16;
//
// Setup the system clock to run at 40 Mhz from PLL with crystal reference
//
ROM_SysCtlClockSet(
SYSCTL_SYSDIV_5 | SYSCTL_USE_PLL | SYSCTL_XTAL_16MHZ
| SYSCTL_OSC_MAIN);
//
// Enable port E used for motion interrupt.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
//
// Enable port F used for calibration.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
//
// Initialize the UART.
//
ConfigureUART();
/* EEPROM SETTINGS */
SysCtlPeripheralEnable(SYSCTL_PERIPH_EEPROM0); // EEPROM activate
EEPROMInit(); // EEPROM start
//
// Print the welcome message to the terminal.
//
UARTprintf("\033[2JMPU9150 Raw Example\n");
//
// Set the color to a purple approximation.
//
g_pui32Colors[RED] = 0x8000;
g_pui32Colors[BLUE] = 0x8000;
g_pui32Colors[GREEN] = 0x8000;
//
// Initialize RGB driver.
//
RGBInit(0);
RGBColorSet(g_pui32Colors);
RGBIntensitySet(0.5f);
RGBEnable();
// Initialize BGLib
bglib_output = output;
ConfigureBLE();
//
// The I2C3 peripheral must be enabled before use.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C3);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
//
// Configure the pin muxing for I2C3 functions on port D0 and D1.
//
ROM_GPIOPinConfigure(GPIO_PD0_I2C3SCL);
ROM_GPIOPinConfigure(GPIO_PD1_I2C3SDA);
//
// Select the I2C function for these pins. This function will also
// configure the GPIO pins pins for I2C operation, setting them to
// open-drain operation with weak pull-ups. Consult the data sheet
// to see which functions are allocated per pin.
//
GPIOPinTypeI2CSCL(GPIO_PORTD_BASE, GPIO_PIN_0);
ROM_GPIOPinTypeI2C(GPIO_PORTD_BASE, GPIO_PIN_1);
//
// Configure and Enable the GPIO interrupt. Used for INT signal from the
// MPU9150
//
ROM_GPIOPinTypeGPIOInput(GPIO_PORTE_BASE, GPIO_PIN_2);
GPIOIntEnable(GPIO_PORTE_BASE, GPIO_PIN_2);
ROM_GPIOIntTypeSet(GPIO_PORTE_BASE, GPIO_PIN_2, GPIO_FALLING_EDGE);
ROM_IntEnable(INT_GPIOE);
//
// Keep only some parts of the systems running while in sleep mode.
// GPIOE is for the MPU9150 interrupt pin.
// UART0 is the virtual serial port
// TIMER0, TIMER1 and WTIMER5 are used by the RGB driver
// I2C3 is the I2C interface to the ISL29023
//
ROM_SysCtlPeripheralClockGating(true);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOE);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UART0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER1);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_I2C3);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_WTIMER5);
//
// Enable interrupts to the processor.
//
ROM_IntMasterEnable();
//
// Initialize I2C3 peripheral.
//
I2CMInit(&g_sI2CInst, I2C3_BASE, INT_I2C3, 0xff, 0xff,
ROM_SysCtlClockGet());
//
// Initialize the MPU9150 Driver.
//
MPU9150Init(&g_sMPU9150Inst, &g_sI2CInst, MPU9150_I2C_ADDRESS,
MPU9150AppCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Configure the sampling rate to 1000 Hz / (1+24).
//
g_sMPU9150Inst.pui8Data[0] = 24;
MPU9150Write(&g_sMPU9150Inst, MPU9150_O_SMPLRT_DIV, g_sMPU9150Inst.pui8Data,
1, MPU9150AppCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Write application specifice sensor configuration such as filter settings
// and sensor range settings.
//
g_sMPU9150Inst.pui8Data[0] = MPU9150_CONFIG_DLPF_CFG_94_98;
g_sMPU9150Inst.pui8Data[1] = MPU9150_GYRO_CONFIG_FS_SEL_250;
g_sMPU9150Inst.pui8Data[2] = (MPU9150_ACCEL_CONFIG_ACCEL_HPF_5HZ
| MPU9150_ACCEL_CONFIG_AFS_SEL_2G);
// g_sMPU9150Inst.pui8Data[2] = MPU9150_ACCEL_CONFIG_AFS_SEL_2G;
MPU9150Write(&g_sMPU9150Inst, MPU9150_O_CONFIG, g_sMPU9150Inst.pui8Data, 3,
MPU9150AppCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Configure the data ready interrupt pin output of the MPU9150.
//
g_sMPU9150Inst.pui8Data[0] = MPU9150_INT_PIN_CFG_INT_LEVEL
| MPU9150_INT_PIN_CFG_INT_RD_CLEAR
| MPU9150_INT_PIN_CFG_LATCH_INT_EN;
g_sMPU9150Inst.pui8Data[1] = MPU9150_INT_ENABLE_DATA_RDY_EN;
MPU9150Write(&g_sMPU9150Inst, MPU9150_O_INT_PIN_CFG,
g_sMPU9150Inst.pui8Data, 2, MPU9150AppCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Initialize the DCM system. 40 hz sample rate.
// accel weight = .2, gyro weight = .8, mag weight = .2
//
CompDCMInit(&g_sCompDCMInst, 1.0f / 40.0f, 0.2f, 0.6f, 0.2f);
//
// Enable blinking indicates config finished successfully
//
RGBBlinkRateSet(1.0f);
//
// Configure and Enable the GPIO interrupt. Used for calibration
//
HWREG(GPIO_PORTF_BASE + GPIO_O_LOCK) = GPIO_LOCK_KEY;
HWREG(GPIO_PORTF_BASE + GPIO_O_CR) |= 0x01;
ROM_GPIOPinTypeGPIOInput(GPIO_PORTF_BASE, GPIO_PIN_4);
GPIOPadConfigSet(GPIO_PORTF_BASE, GPIO_PIN_4, GPIO_STRENGTH_2MA,
GPIO_PIN_TYPE_STD_WPU);
ROM_IntEnable(INT_GPIOF);
ROM_GPIOIntTypeSet(GPIO_PORTF_BASE, GPIO_PIN_4, GPIO_FALLING_EDGE);
GPIOIntEnable(GPIO_PORTF_BASE, GPIO_PIN_4);
g_calibrationState = 0;
ui32CompDCMStarted = 0;
// Configure the white noise, read the error from EEPROM
EEPROMRead((uint32_t *) zeroErrorAccel,
EEPROM_ZERO_ERROR_ACCELERATION_ADDRESS, 12);
EEPROMRead((uint32_t *) linearErrorAccel,
EEPROM_LINEAR_ERROR_ACCELERATION_ADDRESS, 12);
EEPROMRead((uint32_t *) zeroErrorGyro, EEPROM_ZERO_ERROR_GYROSCOPE_ADDRESS,
12);
while (1) {
//
// Go to sleep mode while waiting for data ready.
//
while (!g_vui8I2CDoneFlag) {
//ROM_SysCtlSleep();
}
//
// Clear the flag
//
g_vui8I2CDoneFlag = 0;
//
// Get floating point version of the Accel Data in m/s^2.
//
MPU9150DataAccelGetFloat(&g_sMPU9150Inst, pfAccel, pfAccel + 1,
pfAccel + 2);
//
// Get floating point version of angular velocities in rad/sec
//
MPU9150DataGyroGetFloat(&g_sMPU9150Inst, pfGyro, pfGyro + 1,
pfGyro + 2);
//
// Get floating point version of magnetic fields strength in tesla
//
MPU9150DataMagnetoGetFloat(&g_sMPU9150Inst, pfMag, pfMag + 1,
pfMag + 2);
if (g_calibrationState == 2) {
zeroErrorAccel[0] = (pfAccel[0]
+ zeroErrorAccel[0] * g_calibrationCount)
/ (g_calibrationCount + 1);
zeroErrorAccel[1] = (pfAccel[1]
+ zeroErrorAccel[1] * g_calibrationCount)
/ (g_calibrationCount + 1);
accelAtGravity[2] = (pfAccel[2]
+ accelAtGravity[2] * g_calibrationCount)
/ (g_calibrationCount + 1);
zeroErrorGyro[0] = (pfGyro[0]
+ zeroErrorGyro[0] * g_calibrationCount)
/ (g_calibrationCount + 1);
zeroErrorGyro[1] = (pfGyro[1]
+ zeroErrorGyro[1] * g_calibrationCount)
/ (g_calibrationCount + 1);
zeroErrorGyro[2] = (pfGyro[2]
+ zeroErrorGyro[2] * g_calibrationCount)
/ (g_calibrationCount + 1);
g_calibrationCount++;
if (g_calibrationCount > 500) {
Calibration();
}
continue;
} else if (g_calibrationState == 4) {
zeroErrorAccel[2] = (pfAccel[2]
+ zeroErrorAccel[2] * g_calibrationCount)
/ (g_calibrationCount + 1);
accelAtGravity[1] = (pfAccel[1]
+ accelAtGravity[1] * g_calibrationCount)
/ (g_calibrationCount + 1);
g_calibrationCount++;
if (g_calibrationCount > 500) {
Calibration();
}
continue;
} else if (g_calibrationState == 6) {
accelAtGravity[0] = (pfAccel[0]
+ accelAtGravity[0] * g_calibrationCount)
/ (g_calibrationCount + 1);
g_calibrationCount++;
if (g_calibrationCount > 500) {
Calibration();
}
continue;
}
// Cancel out white noise
// pfAccel[0] = pfAccel[0] - zeroErrorAccel[0];
// pfAccel[1] = pfAccel[1] - zeroErrorAccel[1];
// pfAccel[2] = pfAccel[2] - zeroErrorAccel[2];
// pfGyro[0] = pfGyro[0] - zeroErrorGyro[0];
// pfGyro[1] = pfGyro[1] - zeroErrorGyro[1];
// pfGyro[2] = pfGyro[2] - zeroErrorGyro[2];
// // Straighten out linear noise
// pfAccel[0] = pfAccel[0] * (1 + linearErrorAccel[0]);
// pfAccel[1] = pfAccel[1] * (1 + linearErrorAccel[1]);
// pfAccel[2] = pfAccel[2] * (1 + linearErrorAccel[2]);
//
// Check if this is our first data ever.
//
if (ui32CompDCMStarted == 0) {
//
// Set flag indicating that DCM is started.
// Perform the seeding of the DCM with the first data set.
//
ui32CompDCMStarted = 1;
CompDCMMagnetoUpdate(&g_sCompDCMInst, pfMag[0], pfMag[1], pfMag[2]);
CompDCMAccelUpdate(&g_sCompDCMInst, pfAccel[0], pfAccel[1],
pfAccel[2]);
CompDCMGyroUpdate(&g_sCompDCMInst, pfGyro[0], pfGyro[1], pfGyro[2]);
CompDCMStart(&g_sCompDCMInst);
} else {
//
// DCM Is already started. Perform the incremental update.
//
CompDCMMagnetoUpdate(&g_sCompDCMInst, pfMag[0], pfMag[1], pfMag[2]);
CompDCMAccelUpdate(&g_sCompDCMInst, pfAccel[0], pfAccel[1],
pfAccel[2]);
CompDCMGyroUpdate(&g_sCompDCMInst, -pfGyro[0], -pfGyro[1],
-pfGyro[2]);
CompDCMUpdate(&g_sCompDCMInst);
}
//
// Increment the skip counter. Skip counter is used so we do not
// overflow the UART with data.
//
g_ui32PrintSkipCounter++;
if (g_ui32PrintSkipCounter >= PRINT_SKIP_COUNT) {
//
// Reset skip counter.
//
g_ui32PrintSkipCounter = 0;
//
// Get Euler data. (Roll Pitch Yaw)
//
CompDCMComputeEulers(&g_sCompDCMInst, pfEulers, pfEulers + 1,
pfEulers + 2);
//
// Get Quaternions.
//
CompDCMComputeQuaternion(&g_sCompDCMInst, pfQuaternion);
//
// convert mag data to micro-tesla for better human interpretation.
//
pfMag[0] *= 1e6;
pfMag[1] *= 1e6;
pfMag[2] *= 1e6;
//
// Convert Eulers to degrees. 180/PI = 57.29...
// Convert Yaw to 0 to 360 to approximate compass headings.
//
pfEulers[0] *= 57.295779513082320876798154814105f;
pfEulers[1] *= 57.295779513082320876798154814105f;
pfEulers[2] *= 57.295779513082320876798154814105f;
if (pfEulers[2] < 0) {
pfEulers[2] += 360.0f;
}
// Use pfMag to display degrees of the Magnetomer's x-axis
// (y-axis of accelerometer and gyroscope) to the east of
// magnetic north pole
// direction[0] = 0;
// if (pfMag[1] == 0) {
// if (pfMag[0] > 0) {
// direction[0] = 0;
// } else {
// direction[0] = 180;
// }
// } else if (pfMag[1] > 0) {
// direction[0] = 90 - atan2f(pfMag[0], pfMag[1]) * 180 / 3.14159265359;
// } else if (pfMag[1] < 0) {
// direction[0] = 270 - atan2f(pfMag[0], pfMag[1]) * 180 / 3.14159265359;
// }
//
// Now drop back to using the data as a single array for the
// purpose of decomposing the float into a integer part and a
// fraction (decimal) part.
//
for (ui32Idx = 0; ui32Idx < 17; ui32Idx++) {
//
// Conver float value to a integer truncating the decimal part.
//
i32IPart[ui32Idx] = (int32_t) pfData[ui32Idx];
//
// Multiply by 1000 to preserve first three decimal values.
// Truncates at the 3rd decimal place.
//
i32FPart[ui32Idx] = (int32_t) (pfData[ui32Idx] * 1000.0f);
//
// Subtract off the integer part from this newly formed decimal
// part.
//
i32FPart[ui32Idx] = i32FPart[ui32Idx]
- (i32IPart[ui32Idx] * 1000);
//
// make the decimal part a positive number for display.
//
if (i32FPart[ui32Idx] < 0) {
i32FPart[ui32Idx] *= -1;
}
}
if (g_bleUserFlag == 1) {
g_bleFlag = 0;
ble_cmd_attributes_write(58, 0, 12, (uint8_t*)pfEuler);
while (g_bleFlag == 0) {
}
} else if (g_bleDisconnectFlag == 1) {
ConfigureBLE();
}
//
// Print the acceleration numbers in the table.
//
// UARTprintf("%3d.%03d, ", i32IPart[0], i32FPart[0]);
// UARTprintf("%3d.%03d, ", i32IPart[1], i32FPart[1]);
// UARTprintf("%3d.%03d\n", i32IPart[2], i32FPart[2]);
//
// //
// // Print the angular velocities in the table.
// //
// UARTprintf("%3d.%03d, ", i32IPart[3], i32FPart[3]);
// UARTprintf("%3d.%03d, ", i32IPart[4], i32FPart[4]);
// UARTprintf("%3d.%03d\n", i32IPart[5], i32FPart[5]);
//
// //
// // Print the magnetic data in the table.
// //
// UARTprintf("%3d.%03d, ", i32IPart[6], i32FPart[6]);
// UARTprintf("%3d.%03d, ", i32IPart[7], i32FPart[7]);
// UARTprintf("%3d.%03d\n", i32IPart[8], i32FPart[8]);
//
// //
// // Print the direction in the table.
// //
// UARTprintf("%3d.%03d\n", i32IPart[16], i32FPart[16]);
// //
// // Print the Eulers in a table.
// //
// UARTprintf("%3d.%03d, ", i32IPart[9], i32FPart[9]);
// UARTprintf("%3d.%03d, ", i32IPart[10], i32FPart[10]);
// UARTprintf("%3d.%03d\n", i32IPart[11], i32FPart[11]);
//
// //
// // Print the quaternions in a table format.
// //
// UARTprintf("\033[19;14H%3d.%03d", i32IPart[12], i32FPart[12]);
// UARTprintf("\033[19;32H%3d.%03d", i32IPart[13], i32FPart[13]);
// UARTprintf("\033[19;50H%3d.%03d", i32IPart[14], i32FPart[14]);
// UARTprintf("\033[19;68H%3d.%03d", i32IPart[15], i32FPart[15]);
}
}
}
void initsensorhub(void)
{
//
// Enable port B used for motion interrupt.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
//
// Initialize the UART.
//
ConfigureUART();
//
// Print the welcome message to the terminal.
//
UARTprintf("\033[2JMPU9150 Raw Example\n");
//
// Set the color to a purple approximation.
//
g_pui32Colors[RED] = 0x8000;
g_pui32Colors[BLUE] = 0x8000;
g_pui32Colors[GREEN] = 0x0000;
//
// Initialize RGB driver.
//
RGBInit(0);
RGBColorSet(g_pui32Colors);
RGBIntensitySet(0.5f);
RGBEnable();
//
// The I2C3 peripheral must be enabled before use.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C3);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
//
// Configure the pin muxing for I2C3 functions on port D0 and D1.
//
ROM_GPIOPinConfigure(GPIO_PD0_I2C3SCL);
ROM_GPIOPinConfigure(GPIO_PD1_I2C3SDA);
//
// Select the I2C function for these pins. This function will also
// configure the GPIO pins pins for I2C operation, setting them to
// open-drain operation with weak pull-ups. Consult the data sheet
// to see which functions are allocated per pin.
//
GPIOPinTypeI2CSCL(GPIO_PORTD_BASE, GPIO_PIN_0);
ROM_GPIOPinTypeI2C(GPIO_PORTD_BASE, GPIO_PIN_1);
//
// Configure and Enable the GPIO interrupt. Used for INT signal from the
// MPU9150
//
ROM_GPIOPinTypeGPIOInput(GPIO_PORTB_BASE, GPIO_PIN_2);
GPIOIntEnable(GPIO_PORTB_BASE, GPIO_PIN_2);
ROM_GPIOIntTypeSet(GPIO_PORTB_BASE, GPIO_PIN_2, GPIO_FALLING_EDGE);
ROM_IntEnable(INT_GPIOB);
//
// Keep only some parts of the systems running while in sleep mode.
// GPIOB is for the MPU9150 interrupt pin.
// UART0 is the virtual serial port
// TIMER0, TIMER1 and WTIMER5 are used by the RGB driver
// I2C3 is the I2C interface to the ISL29023
//
ROM_SysCtlPeripheralClockGating(true);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UART0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER0);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_TIMER1);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_I2C3);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_WTIMER5);
//
// Enable interrupts to the processor.
//
ROM_IntMasterEnable();
//
// Initialize I2C3 peripheral.
//
I2CMInit(&g_sI2CInst, I2C3_BASE, INT_I2C3, 0xff, 0xff,
ROM_SysCtlClockGet());
//
// Initialize the MPU9150 Driver.
//
MPU9150Init(&g_sMPU9150Inst, &g_sI2CInst, MPU9150_I2C_ADDRESS,
MPU9150AppCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Write application specifice sensor configuration such as filter settings
// and sensor range settings.
//
g_sMPU9150Inst.pui8Data[0] = MPU9150_CONFIG_DLPF_CFG_94_98;
g_sMPU9150Inst.pui8Data[1] = MPU9150_GYRO_CONFIG_FS_SEL_250;
g_sMPU9150Inst.pui8Data[2] = (MPU9150_ACCEL_CONFIG_ACCEL_HPF_5HZ |
MPU9150_ACCEL_CONFIG_AFS_SEL_2G);
MPU9150Write(&g_sMPU9150Inst, MPU9150_O_CONFIG, g_sMPU9150Inst.pui8Data, 3,
MPU9150AppCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Configure the data ready interrupt pin output of the MPU9150.
//
g_sMPU9150Inst.pui8Data[0] = MPU9150_INT_PIN_CFG_INT_LEVEL |
MPU9150_INT_PIN_CFG_INT_RD_CLEAR |
MPU9150_INT_PIN_CFG_LATCH_INT_EN;
g_sMPU9150Inst.pui8Data[1] = MPU9150_INT_ENABLE_DATA_RDY_EN;
MPU9150Write(&g_sMPU9150Inst, MPU9150_O_INT_PIN_CFG,
g_sMPU9150Inst.pui8Data, 2, MPU9150AppCallback,
&g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MPU9150AppI2CWait(__FILE__, __LINE__);
//
// Initialize the DCM system. 50 hz sample rate.
// accel weight = .2, gyro weight = .8, mag weight = .2
//
CompDCMInit(&g_sCompDCMInst, 1.0f / 50.0f, 0.2f, 0.6f, 0.2f);
UARTprintf("\033[2J\033[H");
UARTprintf("MPU9150 9-Axis Simple Data Application Example\n\n");
UARTprintf("\033[20GX\033[31G|\033[43GY\033[54G|\033[66GZ\n\n");
UARTprintf("Accel\033[8G|\033[31G|\033[54G|\n\n");
UARTprintf("Gyro\033[8G|\033[31G|\033[54G|\n\n");
UARTprintf("Mag\033[8G|\033[31G|\033[54G|\n\n");
UARTprintf("\n\033[20GRoll\033[31G|\033[43GPitch\033[54G|\033[66GYaw\n\n");
UARTprintf("Eulers\033[8G|\033[31G|\033[54G|\n\n");
UARTprintf("\n\033[17GQ1\033[26G|\033[35GQ2\033[44G|\033[53GQ3\033[62G|"
"\033[71GQ4\n\n");
UARTprintf("Q\033[8G|\033[26G|\033[44G|\033[62G|\n\n");
//
// Enable blinking indicates config finished successfully
//
RGBBlinkRateSet(1.0f);
//
// Initialize convenience pointers that clean up and clarify the code
// meaning. We want all the data in a single contiguous array so that
// we can make our pretty printing easier later.
//
pfAccel = pfData;
pfGyro = pfData + 3;
pfMag = pfData + 6;
pfEulers = pfData + 9;
pfQuaternion = pfData + 12;
}
int main(void)
{
// setup the system clock to run at 80 MHz from the external crystal:
ROM_SysCtlClockSet(SYSCTL_SYSDIV_2_5 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN | SYSCTL_XTAL_16MHZ);
// enable peripherals to operate when CPU is in sleep:
ROM_SysCtlPeripheralClockGating(true);
// enable all of the GPIOs:
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOC);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOA);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOC);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOD);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOE);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_GPIOF);
// setup pins connected to RGB LED:
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3);
//setup the UART console
InitConsole();
// Test either the interrupts on a simple pushbutton to turn-on a led:
// 1- interrupt with static allocation on the vector table
// 2- interrupt with dynamic allocation on the vector table
// 2- interrupt with dynamic allocation on the vector table
// setup pin connected to SW1 and SW2
// Unlock PF0 so we can change it to a GPIO input
// Once we have enabled (unlocked) the commit register then re-lock it
// to prevent further changes. PF0 is muxed with NMI thus a special case.
HWREG(GPIO_PORTF_BASE + GPIO_O_LOCK) = GPIO_LOCK_KEY;
HWREG(GPIO_PORTF_BASE + GPIO_O_CR) |= 0x01;
HWREG(GPIO_PORTF_BASE + GPIO_O_AFSEL) |= 0x000;
HWREG(GPIO_PORTF_BASE + GPIO_O_LOCK) = 0;
//Configures pin(s) for use as GPIO inputs
ROM_GPIOPinTypeGPIOInput(GPIO_PORTF_BASE,GPIO_PIN_4 | GPIO_PIN_0);
//Sets the pad configuration for the specified pin(s).
ROM_GPIOPadConfigSet(GPIO_PORTF_BASE,GPIO_PIN_4 | GPIO_PIN_0,GPIO_STRENGTH_2MA,GPIO_PIN_TYPE_STD_WPU);
// Make PORT F pin 0,4 high level triggered interrupts.
ROM_GPIOIntTypeSet(GPIO_PORTF_BASE,GPIO_PIN_4 | GPIO_PIN_0,GPIO_BOTH_EDGES);
//dynamic allocation on the vector table of GPIO_PORTF_isr interrupt handler
GPIOIntRegister(GPIO_PORTF_BASE, GPIO_PORTF_isr);
//Enables the specified GPIO interrupt
IntEnable(INT_GPIOF);
GPIOIntEnable(GPIO_PORTF_BASE,GPIO_INT_PIN_4 | GPIO_INT_PIN_0);
IntMasterEnable();
uint8_t PORTF_status;
//uint32_t ui32Loop = 0;
//
// Loop forever
//
while(1)
{
uint8_t PORTF_status=GPIOPinRead(GPIO_PORTF_BASE,GPIO_PIN_0 | GPIO_PIN_4);
/*
if(GPIOPinRead(GPIO_PORTF_BASE,GPIO_PIN_4))
{
ROM_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3 ,0);
}
else
{
ROM_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3 , GPIO_PIN_1);
}
*/
/*
//
// Turn on the red LED .
//
ROM_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3 , GPIO_PIN_1);
ROM_GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_7, GPIO_PIN_7);
//
// Delay for a bit.
//
for(ui32Loop = 0; ui32Loop < 2000000; ui32Loop++)
{
}
//
// Turn on the green LED.
//
ROM_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3 , GPIO_PIN_2);
ROM_GPIOPinWrite(GPIO_PORTB_BASE, GPIO_PIN_7, 0);
//
// Delay for a bit.
//
for(ui32Loop = 0; ui32Loop < 2000000; ui32Loop++)
{
}
//
// Turn on the blue LED.
//
ROM_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3 , GPIO_PIN_3);
//
// Delay for a bit.
//
for(ui32Loop = 0; ui32Loop < 2000000; ui32Loop++)
{
}
*/
}
}
void SSI3DMASlaveClass::configureDMA() {
//Enable uDMA
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_UDMA);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_UDMA);
//Register DMA interrupt to handler
IntRegister(INT_UDMAERR, uDMAErrorHandler);
//Enable interrupt
ROM_IntEnable(INT_UDMAERR);
// Enable the uDMA controller.
ROM_uDMAEnable();
// Point at the control table to use for channel control structures.
ROM_uDMAControlBaseSet(pui8ControlTable);
//Assign DMA channels to SSI3
ROM_uDMAChannelAssign(UDMA_CH14_SSI3RX);
ROM_uDMAChannelAssign(UDMA_CH15_SSI3TX);
// Put the attributes in a known state for the uDMA SSI0RX channel. These
// should already be disabled by default.
ROM_uDMAChannelAttributeDisable(UDMA_CH14_SSI3RX, UDMA_ATTR_USEBURST | UDMA_ATTR_ALTSELECT |
(UDMA_ATTR_HIGH_PRIORITY | UDMA_ATTR_REQMASK));
// Configure the control parameters for the primary control structure for
// the SSIORX channel.
ROM_uDMAChannelControlSet(UDMA_CH14_SSI3RX | UDMA_PRI_SELECT,
UDMA_SIZE_8 | UDMA_SRC_INC_NONE | UDMA_DST_INC_8 |
UDMA_ARB_4);
//Enable DMA channel to write in the next buffer position
ROM_uDMAChannelTransferSet(UDMA_CH14_SSI3RX | UDMA_PRI_SELECT,
UDMA_MODE_BASIC,
(void *)(SSI3_BASE + SSI_O_DR),
g_ui8SSIRxBuf[g_ui8RxWriteIndex], sizeof(g_ui8SSIRxBuf[g_ui8RxWriteIndex]));
// Configure TX
//
// Put the attributes in a known state for the uDMA SSI0TX channel. These
// should already be disabled by default.
//
ROM_uDMAChannelAttributeDisable(UDMA_CH15_SSI3TX,
UDMA_ATTR_ALTSELECT |
UDMA_ATTR_HIGH_PRIORITY |
UDMA_ATTR_REQMASK);
// //
// // Configure the control parameters for the primary control structure for
// // the SSIORX channel.
// //
// ROM_uDMAChannelControlSet(UDMA_CH15_SSI3TX | UDMA_PRI_SELECT,
// UDMA_SIZE_8 | UDMA_SRC_INC_NONE | UDMA_DST_INC_NONE |
// UDMA_ARB_4);
//
// //Configure TX to always write 0xFF?
// g_ui8SSITxBuf[0] = 0xFF;
//
// //Enable DMA channel to write in the next buffer position
// ROM_uDMAChannelTransferSet(UDMA_CH15_SSI3TX | UDMA_PRI_SELECT,
// UDMA_MODE_BASIC, g_ui8SSITxBuf,
// (void *)(SSI3_BASE + SSI_O_DR),
// sizeof(g_ui8SSITxBuf));
ROM_uDMAChannelEnable(UDMA_CH14_SSI3RX);
// ROM_uDMAChannelEnable(UDMA_CH15_SSI3TX);
// //
// // Enable the SSI3 DMA TX/RX interrupts.
// //
// ROM_SSIIntEnable(SSI3_BASE, SSI_DMARX);
//
// //
// // Enable the SSI3 peripheral interrupts.
// //
// ROM_IntEnable(INT_SSI3);
}
//*****************************************************************************
//
// Initializes the SSI1 peripheral and sets up the TX and RX uDMA channels.
// The SSI is configured for loopback mode so that any data sent on TX will be
// received on RX. The uDMA channels are configured so that the TX channel
// will copy data from a buffer to the SSI TX output. And the uDMA RX channel
// will receive any incoming data into a pair of buffers in ping-pong mode.
//
//*****************************************************************************
void
InitSSI2Transfer(void)
{
unsigned long SysClock=ROM_SysCtlClockGet();
//
// Enable the SSI peripheral, and configure it to operate even if the CPU
// is in sleep.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_SSI2);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralSleepEnable(SYSCTL_PERIPH_SSI2);
UARTprintf("%u\n",SysClock);
GPIOPinConfigure(GPIO_PB4_SSI2CLK);
GPIOPinWrite(GPIO_PORTE_BASE, GPIO_PIN_3, GPIO_PIN_3);
GPIOPinConfigure(GPIO_PB5_SSI2FSS);
GPIOPinConfigure(GPIO_PB6_SSI2RX);
GPIOPinConfigure(GPIO_PB7_SSI2TX);
GPIOPinTypeSSI(GPIO_PORTB_BASE, GPIO_PIN_4|GPIO_PIN_5|GPIO_PIN_6|GPIO_PIN_7);
//
// Configure the SSI communication parameters.
//
//UARTprintf("%u\n",SysClock);
ROM_SSIConfigSetExpClk(SSI2_BASE, SysClock,
SSI_FRF_MOTO_MODE_1,
SSI_MODE_SLAVE,
1000000,
16);
//
// Set both the TX and RX trigger thresholds to 4. This will be used by
// the uDMA controller to signal when more data should be transferred. The
// uDMA TX and RX channels will be configured so that it can transfer 4
// bytes in a burst when the SSI is ready to transfer more data.
//
//ROM_SSIFIFOLevelSet(SSI2_BASE, SSI_FIFO_TX4_8, SSI_FIFO_RX4_8);
HWREG(SSI2_BASE + SSI_O_CR1) |= 0x00000020; // set Slave Bypass mode
//
// Enable the SSI for operation, and enable the uDMA interface for both TX
// and RX channels.
//
ROM_SSIEnable(SSI2_BASE);
ROM_SSIDMAEnable(SSI2_BASE, SSI_DMA_RX | SSI_DMA_TX);
//
// This register write will set the SSI to operate in loopback mode. Any
// data sent on the TX output will be received on the RX input.
//
//
// Enable the SSI peripheral interrupts. Note that no SSI interrupts
// were enabled, but the uDMA controller will cause an interrupt on the
// SSI interrupt signal when a uDMA transfer is complete.
//
ROM_IntEnable(INT_SSI2);
//
// Put the attributes in a known state for the uDMA SSI2RX channel. These
// should already be disabled by default.
//
ROM_uDMAChannelAttributeDisable(UDMA_CHANNEL_SSI2TX,
UDMA_ATTR_ALTSELECT | UDMA_ATTR_USEBURST |
UDMA_ATTR_HIGH_PRIORITY |
UDMA_ATTR_REQMASK);
ROM_uDMAChannelAssign(UDMA_CH13_SSI2TX);
//
// Configure the control parameters for the primary control structure for
// the SSI RX channel. The primary contol structure is used for the "A"
// part of the ping-pong receive. The transfer data size is 8 bits, the
// source address does not increment since it will be reading from a
// register. The destination address increment is byte 8-bit bytes. The
// arbitration size is set to 4 to match the RX FIFO trigger threshold.
// The uDMA controller will use a 4 byte burst transfer if possible. This
// will be somewhat more effecient that single byte transfers.
//
ROM_uDMAChannelControlSet(UDMA_CHANNEL_SSI2TX | UDMA_PRI_SELECT,
UDMA_SIZE_16 | UDMA_SRC_INC_16 | UDMA_DST_INC_NONE |
UDMA_ARB_4);
//
// Configure the control parameters for the alternate control structure for
// the SSI RX channel. The alternate contol structure is used for the "B"
// part of the ping-pong receive. The configuration is identical to the
// primary/A control structure.
//
ROM_uDMAChannelControlSet(UDMA_CHANNEL_SSI2TX | UDMA_ALT_SELECT,
UDMA_SIZE_16 | UDMA_SRC_INC_16 | UDMA_DST_INC_NONE |
UDMA_ARB_4);
//
// Set up the transfer parameters for the SSI RX primary control
// structure. The mode is set to ping-pong, the transfer source is the
// SSI data register, and the destination is the receive "A" buffer. The
// transfer size is set to match the size of the buffer.
//
ROM_uDMAChannelTransferSet(UDMA_CHANNEL_SSI2TX | UDMA_PRI_SELECT,
UDMA_MODE_PINGPONG,
(void *)g_uiSsiTxBufA,
(void *)(SSI2_BASE + SSI_O_DR),
SSI_TXBUF_SIZE);
//
// Set up the transfer parameters for the SSI RX alternate control
// structure. The mode is set to ping-pong, the transfer source is the
// SSI data register, and the destination is the receive "B" buffer. The
// transfer size is set to match the size of the buffer.
//
ROM_uDMAChannelTransferSet(UDMA_CHANNEL_SSI2TX | UDMA_ALT_SELECT,
UDMA_MODE_PINGPONG,
(void *)g_uiSsiTxBufB,
(void *)(SSI2_BASE + SSI_O_DR),
SSI_TXBUF_SIZE);
ROM_uDMAChannelAttributeEnable(UDMA_CHANNEL_SSI2TX, UDMA_ATTR_USEBURST);
UARTprintf("A_base: %X \n",(void *)g_uiSsiTxBufA);
UARTprintf("B_base: %X \n",(void *)(g_uiSsiTxBufB));
//
// Put the attributes in a known state for the uDMA SSI2TX channel. These
// should already be disabled by default.
//
ROM_uDMAChannelAttributeDisable(UDMA_CHANNEL_SSI2RX,
UDMA_ATTR_ALTSELECT |
UDMA_ATTR_HIGH_PRIORITY |
UDMA_ATTR_REQMASK);
ROM_uDMAChannelAssign(UDMA_CH12_SSI2RX);
//
// Set the USEBURST attribute for the uDMA SSI RX channel. This will
// force the controller to always use a burst when transferring data from
// the TX buffer to the SSI. This is somewhat more effecient bus usage
// than the default which allows single or burst transfers.
//
ROM_uDMAChannelAttributeEnable(UDMA_CHANNEL_SSI2RX, UDMA_ATTR_USEBURST);
//
// Configure the control parameters for the SSI TX. The uDMA SSI TX
// channel is used to transfer a block of data from a buffer to the SSI.
// The data size is 8 bits. The source address increment is 8-bit bytes
// since the data is coming from a buffer. The destination increment is
// none since the data is to be written to the SSI data register. The
// arbitration size is set to 4, which matches the SSI TX FIFO trigger
// threshold.
//
ROM_uDMAChannelControlSet(UDMA_CHANNEL_SSI2RX | UDMA_PRI_SELECT,
UDMA_SIZE_16 | UDMA_SRC_INC_NONE | UDMA_DST_INC_16 |
UDMA_ARB_4);
//
// Set up the transfer parameters for the uDMA SSI TX channel. This will
// configure the transfer source and destination and the transfer size.
// Basic mode is used because the peripheral is making the uDMA transfer
// request. The source is the TX buffer and the destination is the SSI
// data register.
//
ROM_uDMAChannelTransferSet(UDMA_CHANNEL_SSI2RX | UDMA_PRI_SELECT,
UDMA_MODE_BASIC,
(void *)(SSI2_BASE + SSI_O_DR),
(void *)g_uiSsiRxBuf,
SSI_RXBUF_SIZE);
//
// Now both the uDMA SSI TX and RX channels are primed to start a
// transfer. As soon as the channels are enabled, the peripheral will
// issue a transfer request and the data transfers will begin.
//
ROM_uDMAChannelEnable(UDMA_CHANNEL_SSI2TX);
ROM_uDMAChannelEnable(UDMA_CHANNEL_SSI2RX);
GPIOPinWrite(GPIO_PORTE_BASE, GPIO_PIN_3, 0);
}
