DRESULT disk_write ( BYTE pdrv, /* Physical drive nmuber (0..) */ const BYTE *buff, /* Data to be written */ DWORD sector, /* Sector address (LBA) */ UINT count /* Number of sectors to write (1..128) */ ) { DRESULT res; int32_t result; switch (pdrv) { case 0 : // first (only) drive is SD card res = RES_OK; // assume this works // translate the arguments here while (count) { result = SDWriteBlock(sector, (uint8_t *)buff); // xprintf("\n\rIn disk_write(), SDWriteBlock returns %d.", result); if (result != SDCARD_OK) { res = RES_ERROR; break; } sector++; count--; buff = buff + 512; // SD card library uses sector size of 512; FatFS better, also! } // translate the reslut code here return res; default: break; } return RES_PARERR; }
main() { // Disable JTAG (on RA0 and RA1 ) mJTAGPortEnable( DEBUG_JTAGPORT_OFF ); // Configure the device for maximum performance but do not change the PBDIV // Given the options, this function will change the flash wait states, RAM // wait state and enable prefetch cache but will not change the PBDIV. // The PBDIV value is already set via the pragma FPBDIV option above.. SYSTEMConfig(GetSystemClock(), SYS_CFG_WAIT_STATES | SYS_CFG_PCACHE); initializeUART(); initializeADC(); initializeLCD(); initializeRPG(); /* Initialize SD card */ setup_SDSPI(); SD_setStart(); /* Fill tempBuffer[] with int 0 to 63 * Write it to the current block. * Empty tempBuffer[] to all 0. * Read from the current block to make sure that it returns the right value. */ fillTempBuffer(); testSDReadWrite(tempBuffer); curr_read_block = curr_block; ConfigTimer1(); // Enable Timer1 for second counts configureInterrupts(); // T2CON = 0x8030; // TMR1 on, prescale 1:256 PB mPORTASetPinsDigitalOut( LED_MASK ); // LEDs = output mPORTDSetPinsDigitalIn( PB_MASK_D ); // PBs on D = input curr_state = READY; // enable interrupts INTEnableInterrupts(); int i = 0; while( 1 ) { if (getPrintToUARTFlag() == 1){ LCDMenuControl(); //mPORTAToggleBits( LED_MASK ); convertAndPrintIntegerToString("i => ", i++); convertAndPrintIntegerToString("timeElapse => ", timeElapsed); convertAndPrintIntegerToString("timeElapsedLEDSample => ", timeElapsedLEDSample); convertAndPrintIntegerToString("timeElapsedLEDTurnedOff => ", timeElapsedLEDTurnedOff); convertAndPrintIntegerToString("sampleLEDNow => ", sampleLEDNow); convertAndPrintIntegerToString(" ADC Value => ", getChannel5Value()); printShadowDetect(); printLightLevel(); drawLightDetectedBar(); controlPowerRelay(); switch(curr_state) { case READY : WriteString("State => READY "); break; case SLEEP : WriteString("State => SLEEP "); break; case HIBERNATE : WriteString("State => HIBERNATE"); break; case BUSY : WriteString("State => BUSY "); break; } WriteString("\r"); setPrintToUARTFlag(0); } if (NEW_BYTE_RECEIVED == 1){ curr_state = READY; NEW_BYTE_RECEIVED = 0; //mPORTAToggleBits( LED_MASK ); char tempArray[] = "g"; tempArray[0] = characterByteReceived; WriteString(tempArray); if(curr_state = HIBERNATE) { addByteToBuffer(characterByteReceived); } else { PutCharacter(characterByteReceived); } } if(bufferIndex == 512) { SDWriteBlock(currBlock); currBlock++; bufferIndex = 0; } if((curr_state == READY) && (timeElapsed >= SLEEP_TIMEOUT) && (timeElapsed < HIBERNATE_TIMEOUT)) { curr_state = SLEEP; } else if((curr_state == SLEEP) && (timeElapsed >= HIBERNATE_TIMEOUT)) { curr_state = HIBERNATE; timeElapsed = 0; } if (transmitDataFromSDCard == 1) { transmitDataFromSDCard = 0; forwardDataToPrinter(); } } // main (while) loop return 0; } // main