void LOG_init()
{
// LCD config
// Enable FSMC, GPIOD, GPIOE, GPIOF, GPIOG and AFIO clocks
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_FSMC, ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOD | RCC_APB2Periph_GPIOE |
RCC_APB2Periph_GPIOF | RCC_APB2Periph_GPIOG, ENABLE);
STM3210E_LCD_Init();
LCD_Clear();
}
/**
* @brief Initializes the LCD.
* @param None
* @retval None
*/
void GL_LCD_Init(void)
{
/* Setups the LCD */
#if defined(USE_STM3210C_EVAL)
STM3210C_LCD_Init();
#elif defined (USE_STM3210B_EVAL)
STM3210B_LCD_Init();
#elif defined (USE_STM32100B_EVAL)
STM32100B_LCD_Init();
#elif defined(USE_STM3210E_EVAL)
STM3210E_LCD_Init();
#elif defined(USE_STM32100E_EVAL)
STM32100E_LCD_Init();
#elif defined(USE_STM322xG_EVAL)
STM322xG_LCD_Init();
#elif defined(USE_STM32L152_EVAL)
STM32L152_LCD_Init();
#endif
}
void BSP_Init (void)
{
BSP_IntInit();
RCC_DeInit();
RCC_HSEConfig(RCC_HSE_ON);
RCC_WaitForHSEStartUp();
RCC_HCLKConfig(RCC_SYSCLK_Div1);
RCC_PCLK2Config(RCC_HCLK_Div1);
RCC_PCLK1Config(RCC_HCLK_Div2);
RCC_ADCCLKConfig(RCC_PCLK2_Div6);
FLASH_SetLatency(FLASH_Latency_2);
FLASH_PrefetchBufferCmd(FLASH_PrefetchBuffer_Enable);
RCC_PLLConfig(RCC_PLLSource_HSE_Div1, RCC_PLLMul_9);
RCC_PLLCmd(ENABLE);
while (RCC_GetFlagStatus(RCC_FLAG_PLLRDY) == RESET) {
;
}
RCC_SYSCLKConfig(RCC_SYSCLKSource_PLLCLK);
while (RCC_GetSYSCLKSource() != 0x08) {
;
}
BSP_ADC_Init(); /* Initialize the I/Os for the ADC controls. */
BSP_LED_Init(); /* Initialize the I/Os for the LED controls. */
BSP_PB_Init(); /* Initialize the I/Os for the PB control. */
BSP_Joystick_Init(); /* Initialize the I/Os for the Joystick control. */
STM3210E_LCD_Init();
LCD_Clear(0xFFFF);
}
/**
* @brief Main program.
* @param None
* @retval None
*/
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32f10x_xx.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32f10x.c file
*/
/* Initialize LEDs, Key Button, LCD and COM port(USART) available on
STM3210X-EVAL board ******************************************************/
STM_EVAL_LEDInit(LED1);
STM_EVAL_LEDInit(LED2);
STM_EVAL_LEDInit(LED3);
STM_EVAL_LEDInit(LED4);
/* USARTx configured as follow:
- BaudRate = 115200 baud
- Word Length = 8 Bits
- One Stop Bit
- No parity
- Hardware flow control disabled (RTS and CTS signals)
- Receive and transmit enabled
*/
USART_InitStructure.USART_BaudRate = 115200;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
STM_EVAL_COMInit(COM1, &USART_InitStructure);
/* Initialize the LCD */
#ifdef USE_STM32100B_EVAL
STM32100B_LCD_Init();
#elif defined (USE_STM3210B_EVAL)
STM3210B_LCD_Init();
#elif defined (USE_STM3210E_EVAL)
STM3210E_LCD_Init();
#elif defined (USE_STM3210C_EVAL)
STM3210C_LCD_Init();
#elif defined (USE_STM32100E_EVAL)
STM32100E_LCD_Init();
#endif
/* Display message on STM3210X-EVAL LCD *************************************/
/* Clear the LCD */
LCD_Clear(LCD_COLOR_WHITE);
/* Set the LCD Back Color */
LCD_SetBackColor(LCD_COLOR_BLUE);
/* Set the LCD Text Color */
LCD_SetTextColor(LCD_COLOR_WHITE);
LCD_DisplayStringLine(LCD_LINE_0, (uint8_t *)MESSAGE1);
LCD_DisplayStringLine(LCD_LINE_1, (uint8_t *)MESSAGE2);
LCD_DisplayStringLine(LCD_LINE_2, (uint8_t *)MESSAGE3);
/* Retarget the C library printf function to the USARTx, can be USART1 or USART2
depending on the EVAL board you are using ********************************/
printf("\n\r %s", MESSAGE1);
printf(" %s", MESSAGE2);
printf(" %s\n\r", MESSAGE3);
/* Turn on leds available on STM3210X-EVAL **********************************/
STM_EVAL_LEDOn(LED1);
STM_EVAL_LEDOn(LED2);
STM_EVAL_LEDOn(LED3);
STM_EVAL_LEDOn(LED4);
/* Add your application code here
*/
/* Infinite loop */
while (1)
{
}
}
/*******************************************************************************
* Function Name : Demo_Init
* Description : Initializes the demonstration application.
* Input : None
* Output : None
* Return : None
*******************************************************************************/
void Demo_Init(void)
{
/* RCC system reset(for debug purpose) */
RCC_DeInit();
/* Enable HSE */
RCC_HSEConfig(RCC_HSE_ON);
/* Wait till HSE is ready */
HSEStartUpStatus = RCC_WaitForHSEStartUp();
if(HSEStartUpStatus == SUCCESS)
{
/* Enable Prefetch Buffer */
FLASH_PrefetchBufferCmd(FLASH_PrefetchBuffer_Enable);
/* Flash 2 wait state */
FLASH_SetLatency(FLASH_Latency_2);
/* HCLK = SYSCLK */
RCC_HCLKConfig(RCC_SYSCLK_Div1);
/* PCLK2 = HCLK */
RCC_PCLK2Config(RCC_HCLK_Div1);
/* PCLK1 = HCLK/2 */
RCC_PCLK1Config(RCC_HCLK_Div2);
/* PLLCLK = 8MHz * 9 = 72 MHz */
RCC_PLLConfig(RCC_PLLSource_HSE_Div1, RCC_PLLMul_9);
/* Enable PLL */
RCC_PLLCmd(ENABLE);
/* Wait till PLL is ready */
while(RCC_GetFlagStatus(RCC_FLAG_PLLRDY) == RESET)
{
}
/* Select PLL as system clock source */
RCC_SYSCLKConfig(RCC_SYSCLKSource_PLLCLK);
/* Wait till PLL is used as system clock source */
while(RCC_GetSYSCLKSource() != 0x08)
{
}
}
/* Enable GPIOA, GPIOB, GPIOC, GPIOD, GPIOE, GPIOF, GPIOG and AFIO clocks */
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOB |RCC_APB2Periph_GPIOC
| RCC_APB2Periph_GPIOD | RCC_APB2Periph_GPIOE | RCC_APB2Periph_GPIOF | RCC_APB2Periph_GPIOG
| RCC_APB2Periph_AFIO, ENABLE);
/* TIM1 Periph clock enable */
RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM1, ENABLE);
/*------------------- Resources Initialization -----------------------------*/
/* GPIO Configuration */
GPIO_Config();
/* Interrupt Configuration */
InterruptConfig();
/* Configure the systick */
SysTick_Configuration();
/*------------------- Drivers Initialization -------------------------------*/
/* Initialize the LEDs toogling */
LedShow_Init();
/* Initialize the Low Power application */
LowPower_Init();
/* Initialize the LCD */
STM3210E_LCD_Init();
/* Clear the LCD */
LCD_Clear(White);
/* If HSE is not detected at program startup */
if(HSEStartUpStatus == ERROR)
{
/* Generate NMI exception */
SCB->ICSR |= SCB_ICSR_NMIPENDSET;
}
/* Checks the availability of the bitmap files */
CheckBitmapFilesStatus();
/* Display the STM32 introduction */
STM32Intro();
/* Clear the LCD */
LCD_Clear(White);
/* Initialize the Calendar */
Calendar_Init();
/* Enable Leds toggling */
LedShow(ENABLE);
/* Initialize the Low Power application*/
LowPower_Init();
/* Set the LCD Back Color */
LCD_SetBackColor(Blue);
/* Set the LCD Text Color */
LCD_SetTextColor(White);
/* Initialize the Menu */
Menu_Init();
/* Display the main menu icons */
ShowMenuIcons();
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32f10x_xx.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32f10x.c file
*/
/* NVIC Configuration */
NVIC_Configuration();
/* Initialize the LCD */
#ifdef USE_STM32100E_EVAL
STM32100E_LCD_Init();
#elif defined USE_STM3210E_EVAL
STM3210E_LCD_Init();
#elif defined USE_STM32100B_EVAL
STM32100B_LCD_Init();
#elif defined USE_STM3210B_EVAL
STM3210B_LCD_Init();
#endif
#ifdef USE_STM3210E_EVAL
/* Disable FSMC only for STM32 High-density and XL-density devices */
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_FSMC, DISABLE);
#endif /* USE_STM3210E_EVAL */
/* Initialize the Temperature Sensor */
LM75_Init();
if (LM75_GetStatus() == SUCCESS)
{
#ifdef USE_STM3210E_EVAL
/* Enable FSMC */
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_FSMC, ENABLE);
#endif /* USE_STM3210E_EVAL */
/* Clear the LCD */
LCD_Clear(LCD_COLOR_WHITE);
/* Set the Back Color */
LCD_SetBackColor(LCD_COLOR_BLUE);
/* Set the Text Color */
LCD_SetTextColor(LCD_COLOR_GREEN);
LCD_DisplayStringLine(LCD_LINE_0, " Temperature ");
#ifdef USE_STM3210E_EVAL
/* Disable FSMC */
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_FSMC, DISABLE);
/* Initialize the Temperature Sensor */
LM75_Init();
#endif /* USE_STM3210E_EVAL */
/* Configure the Temperature sensor device STLM75:
- Thermostat mode Interrupt
- Fault tolerance: 00
*/
LM75_WriteConfReg(0x02);
/* Configure the THYS and TOS inorder to use the SMbus alert interrupt */
LM75_WriteReg(LM75_REG_THYS, TEMPERATURE_THYS << 8); /*31ÝC*/
LM75_WriteReg(LM75_REG_TOS, TEMPERATURE_TOS << 8); /*32ÝC*/
I2C_ClearITPendingBit(LM75_I2C, I2C_IT_SMBALERT);
SMbusAlertOccurred = 0;
/* Infinite Loop */
while (1)
{
#ifdef USE_STM3210E_EVAL
/* Disable FSMC */
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_FSMC, DISABLE);
/* Initialize the Temperature Sensor */
LM75_Init();
#endif /* USE_STM3210E_EVAL */
/* Get double of Temperature value */
TempValue = LM75_ReadTemp();
#ifdef USE_STM3210E_EVAL
/* Enable FSMC */
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_FSMC, ENABLE);
#endif /* USE_STM3210E_EVAL */
if (TempValue <= 256)
{
/* Positive temperature measured */
TempCelsiusDisplay[7] = '+';
/* Initialize the temperature sensor value*/
TempValueCelsius = TempValue;
}
else
{
/* Negative temperature measured */
TempCelsiusDisplay[7] = '-';
/* Remove temperature value sign */
TempValueCelsius = 0x200 - TempValue;
}
/* Calculate temperature digits in ÝC */
if ((TempValueCelsius & 0x01) == 0x01)
{
TempCelsiusDisplay[12] = 0x05 + 0x30;
TempFahrenheitDisplay[12] = 0x05 + 0x30;
}
else
{
TempCelsiusDisplay[12] = 0x00 + 0x30;
TempFahrenheitDisplay[12] = 0x00 + 0x30;
}
TempValueCelsius >>= 1;
TempCelsiusDisplay[8] = (TempValueCelsius / 100) + 0x30;
TempCelsiusDisplay[9] = ((TempValueCelsius % 100) / 10) + 0x30;
TempCelsiusDisplay[10] = ((TempValueCelsius % 100) % 10) + 0x30;
if (TempValue > 256)
{
if (((9 * TempValueCelsius) / 5) <= 32)
{
/* Convert temperature ÝC to Fahrenheit */
TempValueFahrenheit = abs (32 - ((9 * TempValueCelsius) / 5));
/* Calculate temperature digits in ÝF */
TempFahrenheitDisplay[8] = (TempValueFahrenheit / 100) + 0x30;
TempFahrenheitDisplay[9] = ((TempValueFahrenheit % 100) / 10) + 0x30;
TempFahrenheitDisplay[10] = ((TempValueFahrenheit % 100) % 10) + 0x30;
/* Positive temperature measured */
TempFahrenheitDisplay[7] = '+';
}
else
{
/* Convert temperature ÝC to Fahrenheit */
TempValueFahrenheit = abs(((9 * TempValueCelsius) / 5) - 32);
/* Calculate temperature digits in ÝF */
TempFahrenheitDisplay[8] = (TempValueFahrenheit / 100) + 0x30;
TempFahrenheitDisplay[9] = ((TempValueFahrenheit % 100) / 10) + 0x30;
TempFahrenheitDisplay[10] = ((TempValueFahrenheit % 100) % 10) + 0x30;
/* Negative temperature measured */
TempFahrenheitDisplay[7] = '-';
}
}
else
{
/* Convert temperature ÝC to Fahrenheit */
TempValueFahrenheit = ((9 * TempValueCelsius) / 5) + 32;
/* Calculate temperature digits in ÝF */
TempFahrenheitDisplay[8] = (TempValueFahrenheit / 100) + 0x30;
TempFahrenheitDisplay[9] = ((TempValueFahrenheit % 100) / 10) + 0x30;
TempFahrenheitDisplay[10] = ((TempValueFahrenheit % 100) % 10) + 0x30;
/* Positive temperature measured */
TempFahrenheitDisplay[7] = '+';
}
/* Display Fahrenheit value on LCD */
for (index = 0; index < 20; index++)
{
LCD_DisplayChar(LCD_LINE_6, (319 - (16 * index)), TempCelsiusDisplay[index]);
LCD_DisplayChar(LCD_LINE_7, (319 - (16 * index)), TempFahrenheitDisplay[index]);
}
if (SMbusAlertOccurred == 1)
{
/* Set the Back Color */
LCD_SetBackColor(LCD_COLOR_BLUE);
/* Set the Text Color */
LCD_SetTextColor(LCD_COLOR_RED);
LCD_DisplayStringLine(LCD_LINE_2, "Warning: Temp exceed");
LCD_DisplayStringLine(LCD_LINE_3, " 32 C ");
}
if (SMbusAlertOccurred == 2)
{
/* Set the Back Color */
LCD_SetBackColor(LCD_COLOR_WHITE);
/* Set the Text Color */
LCD_SetTextColor(LCD_COLOR_WHITE);
LCD_ClearLine(LCD_LINE_2);
LCD_ClearLine(LCD_LINE_3);
SMbusAlertOccurred = 0;
/* Set the Back Color */
LCD_SetBackColor(LCD_COLOR_BLUE);
/* Set the Text Color */
LCD_SetTextColor(LCD_COLOR_GREEN);
}
}
}
void Redbull_Init()
{
char buff[128] = { 0 };
USART_STDIO_Init();
Delay_Init();
Button_GPIO_Config();
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_FSMC, ENABLE);
STM3210E_LCD_Init();
LCD_SetFont(&Font8x12);
LCD_SetColors(LCD_COLOR_WHITE, LCD_COLOR_BLACK);
LCD_WriteRAM_Prepare();
for (int i = 0; i < (320 * 240); i++)
{
LCD_WriteRAM(LCD_COLOR_WHITE);
}
for (int i = 0; i < (320 * 240); i++)
{
LCD_WriteRAM(LCD_COLOR_BLACK);
}
LCD_DisplayStringLine(LINE(0), (uint8_t*) " initializing REDBULL");
LCD_DisplayStringLine(LINE(1), (uint8_t*) " CPU ...............................");
sprintf(buff, "ARM Cortex-M3 @ %dMHz", (int) SystemCoreClock / 1000000);
printRight(1, buff);
LCD_DisplayStringLine(LINE(2), (uint8_t*) " LCD ............................320x240");
LCD_DisplayStringLine(LINE(3), (uint8_t*) " LED ..................................");
LED_Init();
toggleLED(LED1_PIN, 0);
toggleLED(LED2_PIN, LED1_PIN);
toggleLED(LED3_PIN, LED2_PIN);
toggleLED(LED4_PIN, LED3_PIN);
toggleLED(LED5_PIN, LED4_PIN);
toggleLED(LED4_PIN, LED5_PIN);
toggleLED(LED3_PIN, LED4_PIN);
toggleLED(LED2_PIN, LED3_PIN);
toggleLED(LED1_PIN, LED2_PIN);
toggleLED(0, LED1_PIN);
printRight(3, "5");
LCD_DisplayStringLine(LINE(4), (uint8_t*) " RTC ................");
RTC_Init();
RTC_t rtc = { .year = 2011, .month = 12, .mday = 19, .hour = 21, .min = 00 };
//RTC_SetTime(&rtc);
RTC_GetTime(&rtc);
sprintf(buff, "%04d/%02d/%02d %02d:%02d:%02d", rtc.year, rtc.month, rtc.mday, rtc.hour, rtc.min, rtc.sec);
printRight(4, buff);
LCD_DisplayStringLine(LINE(5), (uint8_t*) " USB .................................");
Set_USBClock();
Set_System();
USB_Interrupts_Config();
USB_Init();
printRight(5, "ok");
//IS61LV25616 (512KB)
LCD_DisplayStringLine(LINE(6), (uint8_t*) " SRAM ................................");
SRAM_Init();
uint32_t* RAM = (uint32_t*) Bank1_SRAM3_ADDR;
uint8_t TESTOK = 1;
for (uint32_t i = 0; i < (512 * 1024) / 4; i++)
{
RAM[i] = i;
}
for (uint32_t i = 0; i < (512 * 1024) / 4; i++)
{
if (RAM[i] != i)
{
TESTOK = 0;
}
RAM[i] = 0;
}
if (TESTOK)
{
printRight(6, "IS61LV25616 512KB");
}
else
{
printRight(6, "fail");
}
//M29W128F (2MB)
LCD_DisplayStringLine(LINE(7), (uint8_t*) " NOR .................................");
NOR_Init();
NOR_IDTypeDef norid;
NOR_ReadID(&norid);
printRight(7, "MX29LV160D 2MB");
//HY27UF081G2A (128MB)
LCD_DisplayStringLine(LINE(8), (uint8_t*) " NAND ................................");
NAND_Init();
NAND_IDTypeDef nandid;
NAND_ReadID(&nandid);
printRight(8, "HY27UF081G2A 128MB");
LCD_DisplayStringLine(LINE(9), (uint8_t*) " SDIO ................................");
SD_Init();
SD_CardInfo cardinfo;
SD_GetCardInfo(&cardinfo);
printRight(9, "ok");
}
