//*****************************************************************************
//
// This is the main loop that runs the application.
//
//*****************************************************************************
int
main(void)
{
//
// Set the clocking to run from the PLL at 50MHz.
//
SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
/*
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOG);
GPIOPinConfigure(GPIO_PG4_USB0EPEN);
GPIOPinTypeUSBDigital(GPIO_PORTG_BASE, GPIO_PIN_4);
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOL);
GPIOPinTypeUSBAnalog(GPIO_PORTL_BASE, GPIO_PIN_6 | GPIO_PIN_7);
GPIOPinTypeUSBAnalog(GPIO_PORTB_BASE, GPIO_PIN_0 | GPIO_PIN_1);
*/
//
//
// Set the system tick to fire 100 times per second.
//
SysTickPeriodSet(SysCtlClockGet() / SYSTICKS_PER_SECOND);
SysTickIntEnable();
SysTickEnable();
//
// Pass the USB library our device information, initialize the USB
// controller and connect the device to the bus.
//
USBDHIDMouseInit(0, (tUSBDHIDMouseDevice *)&g_sMouseDevice);
USBDHIDMouseRemoteWakeupRequest((void *)&g_sMouseDevice);
//
// Drop into the main loop.
//
while(1)
{
//
// Wait for USB configuration to complete.
//
while(!g_bConnected)
{
}
//
// Now keep processing the mouse as long as the host is connected.
//
while(g_bConnected)
{
//
// If it is time to move the mouse then do so.
//
if(HWREGBITW(&g_ulCommands, TICK_EVENT) == 1)
{
HWREGBITW(&g_ulCommands, TICK_EVENT) = 0;
MoveHandler();
}
}
}
}
//*****************************************************************************
//
// This is the main loop that runs the application.
//
//*****************************************************************************
int
main(void)
{
//
// Set the clocking to run from the PLL at 50MHz.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Enable the UART.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
GPIOPinConfigure(GPIO_PA0_U0RX);
GPIOPinConfigure(GPIO_PA1_U0TX);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
UARTStdioInit(0);
UARTprintf("\033[2JMouse device application\n");
// Configure USB pins, according to
// http://forum.stellarisiti.com/topic/353-work-around-stellaris-launchpad-usb-serial-example-not-enumerating-correctly/?p=1544
// Enable the GPIO port so we can configure it
SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
// Setup the port to be in USB analog mode. Routes incoming signals to
// on-chip USB PHY
GPIOPinTypeUSBAnalog(GPIO_PORTD_BASE, GPIO_PIN_4 | GPIO_PIN_5);
//
// Set the system tick to fire 100 times per second.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, USB_MODE_DEVICE, 0);
//
// Pass the USB library our device information, initialize the USB
// controller and connect the device to the bus.
//
USBDHIDMouseInit(0, (tUSBDHIDMouseDevice *)&g_sMouseDevice);
//
// Drop into the main loop.
//
while(1)
{
//
// Tell the user what we are doing.
//
UARTprintf("Waiting for host...\n");
//
// Wait for USB configuration to complete.
//
while(!g_bConnected)
{
}
//
// Update the status.
//
UARTprintf("Host connected...\n");
//
// Now keep processing the mouse as long as the host is connected.
//
while(g_bConnected)
{
//
// If it is time to move the mouse then do so.
//
if(HWREGBITW(&g_ulCommands, TICK_EVENT) == 1)
{
HWREGBITW(&g_ulCommands, TICK_EVENT) = 0;
MoveHandler();
}
}
//
// Update the status.
//
UARTprintf("Host disconnected...\n");
}
}
//*****************************************************************************
//
// This is the main loop that runs the application.
//
//*****************************************************************************
int
main(void)
{
//
// Set the clocking to run from the PLL at 50MHz.
//
ROM_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |
SYSCTL_XTAL_16MHZ);
//
// Enable the UART.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
GPIOPinConfigure(GPIO_PA0_U0RX);
GPIOPinConfigure(GPIO_PA1_U0TX);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
UARTStdioInit(0);
UARTprintf("\033[2JMouse device application\n");
//
// Set the system tick to fire 100 times per second.
//
ROM_SysTickPeriodSet(ROM_SysCtlClockGet() / SYSTICKS_PER_SECOND);
ROM_SysTickIntEnable();
ROM_SysTickEnable();
//
// Set the USB stack mode to Device mode with VBUS monitoring.
//
USBStackModeSet(0, USB_MODE_DEVICE, 0);
//
// Pass the USB library our device information, initialize the USB
// controller and connect the device to the bus.
//
USBDHIDMouseInit(0, (tUSBDHIDMouseDevice *)&g_sMouseDevice);
//
// Drop into the main loop.
//
while(1)
{
//
// Tell the user what we are doing.
//
UARTprintf("Waiting for host...\n");
//
// Wait for USB configuration to complete.
//
while(!g_bConnected)
{
}
//
// Update the status.
//
UARTprintf("Host connected...\n");
//
// Now keep processing the mouse as long as the host is connected.
//
while(g_bConnected)
{
//
// If it is time to move the mouse then do so.
//
if(HWREGBITW(&g_ulCommands, TICK_EVENT) == 1)
{
HWREGBITW(&g_ulCommands, TICK_EVENT) = 0;
MoveHandler();
}
}
//
// Update the status.
//
UARTprintf("Host disconnected...\n");
}
}
int main(void)
{
tRectangle sRect;
unsigned int i = 0;
unsigned char *src = (unsigned char *) palette_32b;
unsigned char *dest = (unsigned char *) (g_pucBuffer+4);
MMUConfigAndEnable();
//
//Enable USB module clock
//
USB0ModuleClkConfig();
//
//Enable DM timer 3 module clock
//
DMTimer3ModuleClkConfig();
//
//Enbale touch screen module colock
//
TSCADCModuleClkConfig();
//
//Enable touch screen ADC pinmux
//
TSCADCPinMuxSetUp();
//
//Enbale USB interrupts
//
USBInterruptEnable();
//
//Switch ON LCD back light
//
LCDBackLightEnable();
//
//UDP Pin control
//
UPDNPinControl();
//
//Delay timer setup
//
DelayTimerSetup();
//
//Configures raster to display image
//
SetUpLCD();
//
//Register touch scren interrupt
//
TouchIntRegister();
IntSystemEnable(SYS_INT_TINT3);
IntPrioritySet(SYS_INT_TINT3, 0, AINTC_HOSTINT_ROUTE_IRQ);
IntSystemEnable(SYS_INT_ADC_TSC_GENINT);
IntPrioritySet(SYS_INT_ADC_TSC_GENINT, 0, AINTC_HOSTINT_ROUTE_IRQ);
RasterDMAFBConfig(SOC_LCDC_0_REGS,
(unsigned int)(g_pucBuffer+PALETTE_OFFSET),
(unsigned int)(g_pucBuffer+PALETTE_OFFSET) + sizeof(g_pucBuffer) - 2 -
PALETTE_OFFSET, FRAME_BUFFER_0);
RasterDMAFBConfig(SOC_LCDC_0_REGS,
(unsigned int)(g_pucBuffer+PALETTE_OFFSET),
(unsigned int)(g_pucBuffer+PALETTE_OFFSET) + sizeof(g_pucBuffer) - 2 -
PALETTE_OFFSET, FRAME_BUFFER_1);
src = (unsigned char *) palette_32b;
dest = (unsigned char *) (g_pucBuffer+PALETTE_OFFSET);
// Copy palette info into buffer
for( i = PALETTE_OFFSET; i < (PALETTE_SIZE+PALETTE_OFFSET); i++)
{
*dest++ = *src++;
}
GrOffScreen24BPPInit(&g_s35_480x272x24Display, g_pucBuffer, LCD_WIDTH, LCD_HEIGHT);
// Initialize a drawing context.
GrContextInit(&g_sContext, &g_s35_480x272x24Display);
/* enable End of frame interrupt */
RasterEndOfFrameIntEnable(SOC_LCDC_0_REGS);
/* enable raster */
RasterEnable(SOC_LCDC_0_REGS);
//
// Fill the top 24 rows of the screen with blue to create the banner.
//
sRect.sXMin = 0;
sRect.sYMin = 0;
sRect.sXMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.sYMax = 23;
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
GrRectDraw(&g_sContext, &sRect);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, &g_sFontCm20);
GrStringDrawCentered(&g_sContext, "usb-dev-mouse", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 10, 0);
//
// Fill the top 24 rows of the screen with blue to create the banner.
//
sRect.sXMin = 0;
sRect.sYMin = 25;
sRect.sXMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.sYMax = GrContextDpyHeightGet(&g_sContext) - BUTTON_HEIGHT - 2;
GrContextForegroundSet(&g_sContext, ClrDarkGray);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, ClrRed);
GrRectDraw(&g_sContext, &sRect);
//
// Draw the buttons in their initial (unpressed)state.
//
UpdateDisplay(g_ucButtons, true);
//
//Initialize touch screen
//
TouchInit();
//
//Touch screen Interrupt enbale
//
TouchIntEnable();
//
//Touch Screen Enable
//
TouchEnable();
//
// Initialize the mouse
//
USBDHIDMouseInit(0, (tUSBDHIDMouseDevice *)&g_sMouseDevice);
//
// Drop into the main loop.
//
while(1)
{
//
// Wait for USB configuration to complete.
//
while(!bConnected)
{
}
//
//Wait till someone touches the screen
//
while(!g_iTouch)
{
g_iTouch = TouchDetect();
}
//
//Loop here as long as someone moving the finger/stylus on the touch screen
//
do
{
//
//If so, read the x and Y vlaue and give it to touch handler
//
TouchCoOrdGet(&g_lScreenX, &g_lScreenY);
//
//Call touch handler
//
TouchHandler();
}while(TouchDetect());
//
//Touch is released
//
g_released = 1;
//
//Reset the button status
//
g_ucButtons = 0;
//
//Call the touch handler to update the release status
//
TouchHandler();
//
//Reset the touch flag
//
g_iTouch = 0;
}
}
