/**************************************************************************//**
* @brief main - the entrypoint after reset.
*****************************************************************************/
int main(void)
{
int connectionResult;
USBH_Init_TypeDef is = USBH_INIT_DEFAULT;
BSP_Init(BSP_INIT_DEFAULT); /* Initialize DK board register access */
/* If first word of user data page is non-zero, enable eA Profiler trace */
BSP_TraceProfilerSetup();
CMU_ClockSelectSet(cmuClock_HF, cmuSelect_HFXO);
ConsoleDebugInit(); /* Initialize DK UART port. */
printf("\n\nEFM32 USB Host device enumeration example.\n");
USBH_Init(&is); /* Initialize USB HOST stack */
for (;;)
{
/* Wait for device connection */
printf("\nWaiting for USB device plug-in...\n");
/* Wait for maximum 10 seconds. */
connectionResult = USBH_WaitForDeviceConnectionB( tmpBuf, 10 );
if ( connectionResult == USB_STATUS_OK )
{
printf("\nA device was attached...\n");
if (USBH_QueryDeviceB(tmpBuf, sizeof(tmpBuf), USBH_GetPortSpeed())
== USB_STATUS_OK)
{
USBH_InitDeviceData(&device, tmpBuf, NULL, 0, USBH_GetPortSpeed());
printf( "\nDevice VID/PID is 0x%04X/0x%04X, device bus speed is %s",
device.devDesc.idVendor, device.devDesc.idProduct,
USBH_GetPortSpeed() == PORT_FULL_SPEED ? "FULL" : "LOW" );
GetDeviceStrings();
}
else
{
printf("\nDevice enumeration failure, please unplug device...\n");
}
while ( USBH_DeviceConnected() ){}
printf("\n\nDevice removal detected...");
}
else if ( connectionResult == USB_STATUS_DEVICE_MALFUNCTION )
{
printf("\nA malfunctioning device was attached, please remove...\n");
}
else if ( connectionResult == USB_STATUS_PORT_OVERCURRENT )
{
printf( "\nVBUS overcurrent condition, please remove device.\n" );
}
else if ( connectionResult == USB_STATUS_TIMEOUT )
{
printf("\nNo device was attached...\n");
}
USBH_Stop();
}
}
/***************************************************************************//**
* @brief
* Check if a device is a valid Mass Storage Device.
* A valid device will be fully enumerated and activated.
*
* @param[in] buf
* Enumeration data buffer.
*
* @return
* Returns true if a valid MSD device, false otherwise.
******************************************************************************/
static bool QualifyDevice(uint8_t *buf)
{
int i;
bool retVal = false;
bool epIn = false, epOut = false;
if ((USBH_QGetDeviceDescriptor(buf)->bDeviceClass == 0) &&
(USBH_QGetDeviceDescriptor(buf)->bDeviceSubClass == 0) &&
(USBH_QGetDeviceDescriptor(buf)->bDeviceProtocol == 0) &&
(USBH_QGetInterfaceDescriptor(buf, 0, 0)->bInterfaceClass == USB_CLASS_MSD) &&
(USBH_QGetInterfaceDescriptor(buf, 0, 0)->bInterfaceSubClass == USB_CLASS_MSD_SCSI_CMDSET) &&
(USBH_QGetInterfaceDescriptor(buf, 0, 0)->bInterfaceProtocol == USB_CLASS_MSD_BOT_TRANSPORT) &&
(USBH_QGetInterfaceDescriptor(buf, 0, 0)->bNumEndpoints >= 2))
{
/*
* OK so far, scan through endpoints and look for one BULK IN and
* one BULK OUT endpoint.
*/
for (i = 0; i < USBH_QGetInterfaceDescriptor(buf, 0, 0)->bNumEndpoints; i++)
{
if (USBH_QGetEndpointDescriptor(buf, 0, 0, i)->bmAttributes == USB_EPTYPE_BULK)
{
if (USBH_QGetEndpointDescriptor(buf, 0, 0, i)->bEndpointAddress & USB_EP_DIR_IN)
{
if (!epIn)
{
epIn = true;
epInIndex = i;
}
}
else
{
if (!epOut)
{
epOut = true;
epOutIndex = i;
}
}
}
/* Success ? */
if (epIn && epOut)
break;
}
if ((epIn && epOut) && (epInIndex < 2) && (epOutIndex < 2))
{
/*
* Some MSD devices has more than the two required bulk endpoints.
* We will only accept devices where the two bulk endpoints are
* the two first endpoints within the interface.
*/
USB_PRINTF("\nThis is a valid MSD device.");
retVal = true;
}
}
if (retVal == false)
{
USBH_PrintDeviceDescriptor(USBH_QGetDeviceDescriptor(buf));
USBH_PrintConfigurationDescriptor(USBH_QGetConfigurationDescriptor(buf, 0), USB_CONFIG_DESCSIZE);
USBH_PrintInterfaceDescriptor(USBH_QGetInterfaceDescriptor(buf, 0, 0));
for (i = 0; i < USBH_QGetInterfaceDescriptor(buf, 0, 0)->bNumEndpoints; i++)
{
USBH_PrintEndpointDescriptor(USBH_QGetEndpointDescriptor(buf, 0, 0, i));
}
USB_PRINTF("\nThis is not a valid MSD device, review device descriptors.");
}
else
{
/* All set, activate the device. */
USBH_InitDeviceData(&device, buf, ep, 2, USBH_GetPortSpeed());
PrintDeviceStrings(buf);
USBH_SetAddressB(&device, DEV_ADDR);
USBH_SetConfigurationB(&device, device.confDesc.bConfigurationValue);
/* Assign Host Channels to the endpoints */
USBH_AssignHostChannel(BULK_OUT, 2);
USBH_AssignHostChannel(BULK_IN, 3);
USB_PRINTF("\n\nDevice VID/PID is 0x%04X/0x%04X, device bus speed is %s",
device.devDesc.idVendor, device.devDesc.idProduct,
USBH_GetPortSpeed() == PORT_FULL_SPEED ? "FULL" : "LOW");
}
return retVal;
}