/********************************************************************
* Function: main()
*
* Precondition:
*
* Input: None.
*
* Output: None.
*
* Side Effects: None.
*
* Overview: Main entry function. If there is a trigger or
* if there is no valid application, the device
* stays in firmware upgrade mode.
*
*
* Note: None.
********************************************************************/
INT main(void)
{
UINT pbClk;
UINT bSoftResetFlag = 0;
// Setup configuration
pbClk = SYSTEMConfig(SYS_FREQ, SYS_CFG_WAIT_STATES | SYS_CFG_PCACHE);
InitLED();
TRISBbits.TRISB15 = 1;//test
bSoftResetFlag = *(unsigned int *)(NVM_DATA);
if(bSoftResetFlag == 1)
{
NVMErasePage((void*)NVM_DATA);
NVMWriteWord((void*)(NVM_DATA), (unsigned int)0x00);
}
// Enter firmware upgrade mode if there is a trigger or if the application is not valid
if(bSoftResetFlag == 1 || CheckTrigger() || !ValidAppPresent())
{
// Initialize the transport layer - UART/USB/Ethernet
TRANS_LAYER_Init(pbClk);
while(!FRAMEWORK_ExitFirmwareUpgradeMode()) // Be in loop till framework recieves "run application" command from PC
{
// Enter firmware upgrade mode.
// Be in loop, looking for commands from PC
TRANS_LAYER_Task(); // Run Transport layer tasks
FRAMEWORK_FrameWorkTask(); // Run frame work related tasks (Handling Rx frame, process frame and so on)
// Blink LED (Indicates the user that bootloader is running).
BlinkLED();
}
// Close trasnport layer.
TRANS_LAYER_Close();
}
// No trigger + valid application = run application.
JumpToApp();
return 0;
}
/********************************************************************
* Function: main()
*
* Precondition:
*
* Input: None.
*
* Output: None.
*
* Side Effects: None.
*
* Overview: Main entry function. If there is a trigger or
* if there is no valid application, the device
* stays in firmware upgrade mode.
*
*
* Note: None.
********************************************************************/
INT main(void)
{
UINT pbClk;
// Setup configuration
pbClk = SYSTEMConfig(SYS_FREQ, SYS_CFG_WAIT_STATES | SYS_CFG_PCACHE);
InitLED();
mLED = 0;
TRISAbits.TRISA4 = 1; // TEST pin
CNPDAbits.CNPDA4 = 1; // Pull-down
delay_us( 10 ); // Wait a bit until the port pin got pulled down.
// Enter firmware upgrade mode if there is a trigger or if the application is not valid
if(CheckTrigger() || !ValidAppPresent())
{
// Initialize the transport layer - UART/USB/Ethernet
TRANS_LAYER_Init(pbClk);
while(!FRAMEWORK_ExitFirmwareUpgradeMode()) // Be in loop till framework recieves "run application" command from PC
{
// Enter firmware upgrade mode.
// Be in loop, looking for commands from PC
TRANS_LAYER_Task(); // Run Transport layer tasks
FRAMEWORK_FrameWorkTask(); // Run frame work related tasks (Handling Rx frame, process frame and so on)
// Blink LED (Indicates the user that bootloader is running).
BlinkLED();
}
// Close trasnport layer.
TRANS_LAYER_Close();
mLED = 0;
while ( CheckTrigger() ) {}; // Do not run the application while TEST is still tied to VCC.
}
// No trigger + valid application = run application.
CNPDAbits.CNPDA4 = 0; // turn off Pull-down
JumpToApp();
return 0;
}
void BOOTLDR_Run()
{
volatile UINT i;
FILEHANDLE *myFile;
FILEHANDLE *currentFile;
FW_VERSION newVersion;
CHAR buffer[64];
newVersion.major = 0;
newVersion.minor = 0;
newVersion.build = 0;
//if(!ForcedFirmwareExists() && !NewerFirmwareExists() && ValidAppPresent())
if(!ShouldFlashFirmware(sTargetFile, &newVersion) && ValidAppPresent())
{
// No new firmware to load. Jump
// directly to the application
JumpToApp();
}
// At this point sTargetFile will have the name of the file we should use
//strcpy(sTargetFile, "fw/force/v0_0_2.hex");
myFile = FATFS_fopen(sTargetFile,"r");
if(myFile == NULL)// Make sure the file is present.
{
//Indicate error and stay in while loop.
ErrorFunction();
}
// Erase Flash (Block Erase the program Flash)
EraseFlash();
// Initialize the state-machine to read the records.
record.status = REC_NOT_FOUND;
while(1)
{
// For a faster read, read 512 bytes at a time and buffer it.
readBytes = FATFS_fread((void *)&asciiBuffer[pointer], 1, 512, myFile);
//readBytes = FSfread((void *)&asciiBuffer[pointer],1,512,myFile);
if(readBytes == 0)
{
// Nothing to read. Come out of this loop
// break;
FATFS_fclose(myFile);
// Something fishy. The hex file has ended abruptly, looks like there was no "end of hex record".
//Indicate error and stay in while loop.
ErrorFunction();
}
for(i = 0; i < (readBytes + pointer); i ++)
{
// This state machine seperates-out the valid hex records from the read 512 bytes.
switch(record.status)
{
case REC_FLASHED:
case REC_NOT_FOUND:
if(asciiBuffer[i] == ':')
{
// We have a record found in the 512 bytes of data in the buffer.
record.start = &asciiBuffer[i];
record.len = 0;
record.status = REC_FOUND_BUT_NOT_FLASHED;
}
break;
case REC_FOUND_BUT_NOT_FLASHED:
if((asciiBuffer[i] == 0x0A) || (asciiBuffer[i] == 0xFF))
{
// We have got a complete record. (0x0A is new line feed and 0xFF is End of file)
// Start the hex conversion from element
// 1. This will discard the ':' which is
// the start of the hex record.
ConvertAsciiToHex(&record.start[1],hexRec);
// We're done so let's close the file and update current.txt
if(hexRec[3] == END_OF_FILE_RECORD)
{
FATFS_fclose(myFile);
currentFile = FATFS_fopen("fw/current.txt", "wo");
if(currentFile != NULL)
{
sprintf(buffer, "v%d_%d_%d.hex", newVersion.major, newVersion.minor, newVersion.build);
FATFS_fwrite(buffer, 1, strlen(buffer), currentFile);
FATFS_fclose(currentFile);
}
}
WriteHexRecord2Flash(hexRec);
record.status = REC_FLASHED;
// Blink the green LED to indicate programming in progress
mLED_Green_Toggle();
}
break;
}
// Move to next byte in the buffer.
record.len ++;
}
if(record.status == REC_FOUND_BUT_NOT_FLASHED)
{
// We still have a half read record in the buffer. The next half part of the record is read
// when we read 512 bytes of data from the next file read.
memcpy(asciiBuffer, record.start, record.len);
pointer = record.len;
record.status = REC_NOT_FOUND;
}
else
{
pointer = 0;
}
}//while(1)
}// end BOOTLDR_Run function
/********************************************************************
* Function: main()
********************************************************************/
INT main(void)
{
DWORD count1 = 0;
BYTE timer_ro = 1;
// switch to FRC w/PLL to keep up at higher baud rates (120MHz!
PLLFBD=63;
CLKDIVbits.PLLPOST = 0;
CLKDIVbits.PLLPRE = 0;
__builtin_write_OSCCONH(0x01);
__builtin_write_OSCCONL(OSCCON | 0x01);
while (OSCCONbits.COSC != 0b001);
while (OSCCONbits.LOCK != 1);
// Initialize I/O, UART and timer (interrupt)
initIO();
led1Off();
led2Off();
led3Off();
printString("BL:V1.00:");
if (ValidAppPresent())
{
while(count1<20)
{
if ((SWITCH1 == 0) || (SWITCH2 == 0)) // if either switch gets released, start app
JumpToApp();
// Blink LEDs
if (timer_ro)
{
if (TMR1 > 7000)
{
blinkLEDs();
count1++;
timer_ro = 0;
}
}
else if (TMR1 < 7000)
timer_ro = 1;
}
printString("PB:");
}
else
{
printString("NA:"); // No app present, enter bootloader regardless
}
T1CONbits.TON = 0;
PR1 = 50000; // slow down blinking
T1CONbits.TON = 1;
blink_mode = 1;
// Be in loop till framework recieves "run application" command from PC
while(!ExitFirmwareUpgradeMode())
{
uartTask(); // Run Transport layer tasks
if(FrameWorkTask()) // Run frame work related tasks (Handling Rx frame, process frame and so on)
{
blink_mode = 2; // If we've communicated with the PC, use progress flashing
}
// Blink LEDs
if (timer_ro)
{
if (TMR1 > 25000)
{
if (SWITCH1 && (SWITCH2 == 0)) // reset the device on SWITCH1 press
reset();
blinkLEDs();
timer_ro = 0;
}
}
else if (TMR1 < 25000)
timer_ro = 1;
}
JumpToApp();
return 0;
}
