// only buffer L band for farend
int32_t WebRtcAec_BufferFarend(void* aecInst,
const float* farend,
size_t nrOfSamples) {
Aec* aecpc = aecInst;
size_t newNrOfSamples = nrOfSamples;
float new_farend[MAX_RESAMP_LEN];
const float* farend_ptr = farend;
// Get any error caused by buffering the farend signal.
int32_t error_code = WebRtcAec_GetBufferFarendError(aecInst, farend,
nrOfSamples);
if (error_code != 0)
return error_code;
if (aecpc->skewMode == kAecTrue && aecpc->resample == kAecTrue) {
// Resample and get a new number of samples
WebRtcAec_ResampleLinear(aecpc->resampler,
farend,
nrOfSamples,
aecpc->skew,
new_farend,
&newNrOfSamples);
farend_ptr = new_farend;
}
aecpc->farend_started = 1;
WebRtcAec_SetSystemDelay(
aecpc->aec, WebRtcAec_system_delay(aecpc->aec) + (int)newNrOfSamples);
// Write the time-domain data to |far_pre_buf|.
WebRtc_WriteBuffer(aecpc->far_pre_buf, farend_ptr, newNrOfSamples);
// Transform to frequency domain if we have enough data.
while (WebRtc_available_read(aecpc->far_pre_buf) >= PART_LEN2) {
// We have enough data to pass to the FFT, hence read PART_LEN2 samples.
{
float* ptmp = NULL;
float tmp[PART_LEN2];
WebRtc_ReadBuffer(aecpc->far_pre_buf, (void**)&ptmp, tmp, PART_LEN2);
WebRtcAec_BufferFarendPartition(aecpc->aec, ptmp);
#ifdef WEBRTC_AEC_DEBUG_DUMP
WebRtc_WriteBuffer(
WebRtcAec_far_time_buf(aecpc->aec), &ptmp[PART_LEN], 1);
#endif
}
// Rewind |far_pre_buf| PART_LEN samples for overlap before continuing.
WebRtc_MoveReadPtr(aecpc->far_pre_buf, -PART_LEN);
}
return 0;
}
static void EstBufDelayExtended(aecpc_t* self) {
int reported_delay = self->msInSndCardBuf * sampMsNb * self->rate_factor;
int current_delay = reported_delay - WebRtcAec_system_delay(self->aec);
int delay_difference = 0;
// Before we proceed with the delay estimate filtering we:
// 1) Compensate for the frame that will be read.
// 2) Compensate for drift resampling.
// 3) Compensate for non-causality if needed, since the estimated delay can't
// be negative.
// 1) Compensating for the frame(s) that will be read/processed.
current_delay += FRAME_LEN * self->rate_factor;
// 2) Account for resampling frame delay.
if (self->skewMode == kAecTrue && self->resample == kAecTrue) {
current_delay -= kResamplingDelay;
}
// 3) Compensate for non-causality, if needed, by flushing two blocks.
if (current_delay < PART_LEN) {
current_delay += WebRtcAec_MoveFarReadPtr(self->aec, 2) * PART_LEN;
}
if (self->filtDelay == -1) {
self->filtDelay = WEBRTC_SPL_MAX(0, 0.5 * current_delay);
} else {
self->filtDelay = WEBRTC_SPL_MAX(
0, (short)(0.95 * self->filtDelay + 0.05 * current_delay));
}
delay_difference = self->filtDelay - self->knownDelay;
if (delay_difference > 384) {
if (self->lastDelayDiff < 128) {
self->timeForDelayChange = 0;
} else {
self->timeForDelayChange++;
}
} else if (delay_difference < 128 && self->knownDelay > 0) {
if (self->lastDelayDiff > 384) {
self->timeForDelayChange = 0;
} else {
self->timeForDelayChange++;
}
} else {
self->timeForDelayChange = 0;
}
self->lastDelayDiff = delay_difference;
if (self->timeForDelayChange > 25) {
self->knownDelay = WEBRTC_SPL_MAX((int)self->filtDelay - 256, 0);
}
}
static void EstBufDelayNormal(aecpc_t* aecpc) {
int nSampSndCard = aecpc->msInSndCardBuf * sampMsNb * aecpc->rate_factor;
int current_delay = nSampSndCard - WebRtcAec_system_delay(aecpc->aec);
int delay_difference = 0;
// Before we proceed with the delay estimate filtering we:
// 1) Compensate for the frame that will be read.
// 2) Compensate for drift resampling.
// 3) Compensate for non-causality if needed, since the estimated delay can't
// be negative.
// 1) Compensating for the frame(s) that will be read/processed.
current_delay += FRAME_LEN * aecpc->rate_factor;
// 2) Account for resampling frame delay.
if (aecpc->skewMode == kAecTrue && aecpc->resample == kAecTrue) {
current_delay -= kResamplingDelay;
}
// 3) Compensate for non-causality, if needed, by flushing one block.
if (current_delay < PART_LEN) {
current_delay += WebRtcAec_MoveFarReadPtr(aecpc->aec, 1) * PART_LEN;
}
// We use -1 to signal an initialized state in the "extended" implementation;
// compensate for that.
aecpc->filtDelay = aecpc->filtDelay < 0 ? 0 : aecpc->filtDelay;
aecpc->filtDelay =
WEBRTC_SPL_MAX(0, (short)(0.8 * aecpc->filtDelay + 0.2 * current_delay));
delay_difference = aecpc->filtDelay - aecpc->knownDelay;
if (delay_difference > 224) {
if (aecpc->lastDelayDiff < 96) {
aecpc->timeForDelayChange = 0;
} else {
aecpc->timeForDelayChange++;
}
} else if (delay_difference < 96 && aecpc->knownDelay > 0) {
if (aecpc->lastDelayDiff > 224) {
aecpc->timeForDelayChange = 0;
} else {
aecpc->timeForDelayChange++;
}
} else {
aecpc->timeForDelayChange = 0;
}
aecpc->lastDelayDiff = delay_difference;
if (aecpc->timeForDelayChange > 25) {
aecpc->knownDelay = WEBRTC_SPL_MAX((int)aecpc->filtDelay - 160, 0);
}
}
int32_t WebRtcAec_Process(void *aecInst, const int16_t *nearend,
const int16_t *nearendH, int16_t *out, int16_t *outH,
int16_t nrOfSamples, int16_t msInSndCardBuf,
int32_t skew)
{
aecpc_t *aecpc = aecInst;
int32_t retVal = 0;
short i;
short nBlocks10ms;
short nFrames;
// Limit resampling to doubling/halving of signal
const float minSkewEst = -0.5f;
const float maxSkewEst = 1.0f;
if (aecpc == NULL) {
return -1;
}
if (nearend == NULL) {
aecpc->lastError = AEC_NULL_POINTER_ERROR;
return -1;
}
if (out == NULL) {
aecpc->lastError = AEC_NULL_POINTER_ERROR;
return -1;
}
if (aecpc->initFlag != initCheck) {
aecpc->lastError = AEC_UNINITIALIZED_ERROR;
return -1;
}
// number of samples == 160 for SWB input
if (nrOfSamples != 80 && nrOfSamples != 160) {
aecpc->lastError = AEC_BAD_PARAMETER_ERROR;
return -1;
}
// Check for valid pointers based on sampling rate
if (aecpc->sampFreq == 32000 && nearendH == NULL) {
aecpc->lastError = AEC_NULL_POINTER_ERROR;
return -1;
}
if (msInSndCardBuf < 0) {
msInSndCardBuf = 0;
aecpc->lastError = AEC_BAD_PARAMETER_WARNING;
retVal = -1;
}
else if (msInSndCardBuf > 500) {
msInSndCardBuf = 500;
aecpc->lastError = AEC_BAD_PARAMETER_WARNING;
retVal = -1;
}
// TODO(andrew): we need to investigate if this +10 is really wanted.
msInSndCardBuf += 10;
aecpc->msInSndCardBuf = msInSndCardBuf;
if (aecpc->skewMode == kAecTrue) {
if (aecpc->skewFrCtr < 25) {
aecpc->skewFrCtr++;
}
else {
retVal = WebRtcAec_GetSkew(aecpc->resampler, skew, &aecpc->skew);
if (retVal == -1) {
aecpc->skew = 0;
aecpc->lastError = AEC_BAD_PARAMETER_WARNING;
}
aecpc->skew /= aecpc->sampFactor*nrOfSamples;
if (aecpc->skew < 1.0e-3 && aecpc->skew > -1.0e-3) {
aecpc->resample = kAecFalse;
}
else {
aecpc->resample = kAecTrue;
}
if (aecpc->skew < minSkewEst) {
aecpc->skew = minSkewEst;
}
else if (aecpc->skew > maxSkewEst) {
aecpc->skew = maxSkewEst;
}
#ifdef WEBRTC_AEC_DEBUG_DUMP
(void)fwrite(&aecpc->skew, sizeof(aecpc->skew), 1, aecpc->skewFile);
#endif
}
}
nFrames = nrOfSamples / FRAME_LEN;
nBlocks10ms = nFrames / aecpc->rate_factor;
if (aecpc->ECstartup) {
if (nearend != out) {
// Only needed if they don't already point to the same place.
memcpy(out, nearend, sizeof(short) * nrOfSamples);
}
// The AEC is in the start up mode
// AEC is disabled until the system delay is OK
// Mechanism to ensure that the system delay is reasonably stable.
if (aecpc->checkBuffSize) {
aecpc->checkBufSizeCtr++;
// Before we fill up the far-end buffer we require the system delay
// to be stable (+/-8 ms) compared to the first value. This
// comparison is made during the following 6 consecutive 10 ms
// blocks. If it seems to be stable then we start to fill up the
// far-end buffer.
if (aecpc->counter == 0) {
aecpc->firstVal = aecpc->msInSndCardBuf;
aecpc->sum = 0;
}
if (abs(aecpc->firstVal - aecpc->msInSndCardBuf) <
WEBRTC_SPL_MAX(0.2 * aecpc->msInSndCardBuf, sampMsNb)) {
aecpc->sum += aecpc->msInSndCardBuf;
aecpc->counter++;
}
else {
aecpc->counter = 0;
}
if (aecpc->counter * nBlocks10ms >= 6) {
// The far-end buffer size is determined in partitions of
// PART_LEN samples. Use 75% of the average value of the system
// delay as buffer size to start with.
aecpc->bufSizeStart = WEBRTC_SPL_MIN((3 * aecpc->sum *
aecpc->rate_factor * 8) / (4 * aecpc->counter * PART_LEN),
kMaxBufSizeStart);
// Buffer size has now been determined.
aecpc->checkBuffSize = 0;
}
if (aecpc->checkBufSizeCtr * nBlocks10ms > 50) {
// For really bad systems, don't disable the echo canceller for
// more than 0.5 sec.
aecpc->bufSizeStart = WEBRTC_SPL_MIN((aecpc->msInSndCardBuf *
aecpc->rate_factor * 3) / 40, kMaxBufSizeStart);
aecpc->checkBuffSize = 0;
}
}
// If |checkBuffSize| changed in the if-statement above.
if (!aecpc->checkBuffSize) {
// The system delay is now reasonably stable (or has been unstable
// for too long). When the far-end buffer is filled with
// approximately the same amount of data as reported by the system
// we end the startup phase.
int overhead_elements =
WebRtcAec_system_delay(aecpc->aec) / PART_LEN -
aecpc->bufSizeStart;
if (overhead_elements == 0) {
// Enable the AEC
aecpc->ECstartup = 0;
} else if (overhead_elements > 0) {
// TODO(bjornv): Do we need a check on how much we actually
// moved the read pointer? It should always be possible to move
// the pointer |overhead_elements| since we have only added data
// to the buffer and no delay compensation nor AEC processing
// has been done.
WebRtcAec_MoveFarReadPtr(aecpc->aec, overhead_elements);
// Enable the AEC
aecpc->ECstartup = 0;
}
}
} else {
// AEC is enabled.
EstBufDelay(aecpc);
// Note that 1 frame is supported for NB and 2 frames for WB.
for (i = 0; i < nFrames; i++) {
// Call the AEC.
WebRtcAec_ProcessFrame(aecpc->aec,
&nearend[FRAME_LEN * i],
&nearendH[FRAME_LEN * i],
aecpc->knownDelay,
&out[FRAME_LEN * i],
&outH[FRAME_LEN * i]);
// TODO(bjornv): Re-structure such that we don't have to pass
// |aecpc->knownDelay| as input. Change name to something like
// |system_buffer_diff|.
}
}
#ifdef WEBRTC_AEC_DEBUG_DUMP
{
int16_t far_buf_size_ms = (int16_t)(WebRtcAec_system_delay(aecpc->aec) /
(sampMsNb * aecpc->rate_factor));
(void)fwrite(&far_buf_size_ms, 2, 1, aecpc->bufFile);
(void)fwrite(&aecpc->knownDelay, sizeof(aecpc->knownDelay), 1,
aecpc->delayFile);
}
#endif
return retVal;
}
// only buffer L band for farend
int32_t WebRtcAec_BufferFarend(void *aecInst, const int16_t *farend,
int16_t nrOfSamples)
{
aecpc_t *aecpc = aecInst;
int32_t retVal = 0;
int newNrOfSamples = (int) nrOfSamples;
short newFarend[MAX_RESAMP_LEN];
const int16_t* farend_ptr = farend;
float tmp_farend[MAX_RESAMP_LEN];
const float* farend_float = tmp_farend;
float skew;
int i = 0;
if (aecpc == NULL) {
return -1;
}
if (farend == NULL) {
aecpc->lastError = AEC_NULL_POINTER_ERROR;
return -1;
}
if (aecpc->initFlag != initCheck) {
aecpc->lastError = AEC_UNINITIALIZED_ERROR;
return -1;
}
// number of samples == 160 for SWB input
if (nrOfSamples != 80 && nrOfSamples != 160) {
aecpc->lastError = AEC_BAD_PARAMETER_ERROR;
return -1;
}
skew = aecpc->skew;
if (aecpc->skewMode == kAecTrue && aecpc->resample == kAecTrue) {
// Resample and get a new number of samples
WebRtcAec_ResampleLinear(aecpc->resampler, farend, nrOfSamples, skew,
newFarend, &newNrOfSamples);
farend_ptr = (const int16_t*) newFarend;
}
WebRtcAec_SetSystemDelay(aecpc->aec, WebRtcAec_system_delay(aecpc->aec) +
newNrOfSamples);
#ifdef WEBRTC_AEC_DEBUG_DUMP
WebRtc_WriteBuffer(aecpc->far_pre_buf_s16, farend_ptr,
(size_t) newNrOfSamples);
#endif
// Cast to float and write the time-domain data to |far_pre_buf|.
for (i = 0; i < newNrOfSamples; i++) {
tmp_farend[i] = (float) farend_ptr[i];
}
WebRtc_WriteBuffer(aecpc->far_pre_buf, farend_float,
(size_t) newNrOfSamples);
// Transform to frequency domain if we have enough data.
while (WebRtc_available_read(aecpc->far_pre_buf) >= PART_LEN2) {
// We have enough data to pass to the FFT, hence read PART_LEN2 samples.
WebRtc_ReadBuffer(aecpc->far_pre_buf, (void**) &farend_float, tmp_farend,
PART_LEN2);
WebRtcAec_BufferFarendPartition(aecpc->aec, farend_float);
// Rewind |far_pre_buf| PART_LEN samples for overlap before continuing.
WebRtc_MoveReadPtr(aecpc->far_pre_buf, -PART_LEN);
#ifdef WEBRTC_AEC_DEBUG_DUMP
WebRtc_ReadBuffer(aecpc->far_pre_buf_s16, (void**) &farend_ptr, newFarend,
PART_LEN2);
WebRtc_WriteBuffer(WebRtcAec_far_time_buf(aecpc->aec),
&farend_ptr[PART_LEN], 1);
WebRtc_MoveReadPtr(aecpc->far_pre_buf_s16, -PART_LEN);
#endif
}
return retVal;
}
static void ProcessExtended(aecpc_t* self,
const int16_t* near,
const int16_t* near_high,
int16_t* out,
int16_t* out_high,
int16_t num_samples,
int16_t reported_delay_ms,
int32_t skew) {
int i;
const int num_frames = num_samples / FRAME_LEN;
#if defined(WEBRTC_UNTRUSTED_DELAY)
const int delay_diff_offset = kDelayDiffOffsetSamples;
reported_delay_ms = kFixedDelayMs;
#else
// This is the usual mode where we trust the reported system delay values.
const int delay_diff_offset = 0;
// Due to the longer filter, we no longer add 10 ms to the reported delay
// to reduce chance of non-causality. Instead we apply a minimum here to avoid
// issues with the read pointer jumping around needlessly.
reported_delay_ms = reported_delay_ms < kMinTrustedDelayMs
? kMinTrustedDelayMs
: reported_delay_ms;
// If the reported delay appears to be bogus, we attempt to recover by using
// the measured fixed delay values. We use >= here because higher layers
// may already clamp to this maximum value, and we would otherwise not
// detect it here.
reported_delay_ms = reported_delay_ms >= kMaxTrustedDelayMs
? kFixedDelayMs
: reported_delay_ms;
#endif
self->msInSndCardBuf = reported_delay_ms;
if (!self->farend_started) {
// Only needed if they don't already point to the same place.
if (near != out) {
memcpy(out, near, sizeof(short) * num_samples);
}
if (near_high != out_high) {
memcpy(out_high, near_high, sizeof(short) * num_samples);
}
return;
}
if (self->startup_phase) {
// In the extended mode, there isn't a startup "phase", just a special
// action on the first frame. In the trusted delay case, we'll take the
// current reported delay, unless it's less then our conservative
// measurement.
int startup_size_ms =
reported_delay_ms < kFixedDelayMs ? kFixedDelayMs : reported_delay_ms;
int overhead_elements = (WebRtcAec_system_delay(self->aec) -
startup_size_ms / 2 * self->rate_factor * 8) /
PART_LEN;
WebRtcAec_MoveFarReadPtr(self->aec, overhead_elements);
self->startup_phase = 0;
}
EstBufDelayExtended(self);
{
// |delay_diff_offset| gives us the option to manually rewind the delay on
// very low delay platforms which can't be expressed purely through
// |reported_delay_ms|.
const int adjusted_known_delay =
WEBRTC_SPL_MAX(0, self->knownDelay + delay_diff_offset);
for (i = 0; i < num_frames; ++i) {
WebRtcAec_ProcessFrame(self->aec,
&near[FRAME_LEN * i],
&near_high[FRAME_LEN * i],
adjusted_known_delay,
&out[FRAME_LEN * i],
&out_high[FRAME_LEN * i]);
}
}
}
int32_t WebRtcAec_Process(void* aecInst,
const int16_t* nearend,
const int16_t* nearendH,
int16_t* out,
int16_t* outH,
int16_t nrOfSamples,
int16_t msInSndCardBuf,
int32_t skew) {
aecpc_t* aecpc = aecInst;
int32_t retVal = 0;
if (nearend == NULL) {
aecpc->lastError = AEC_NULL_POINTER_ERROR;
return -1;
}
if (out == NULL) {
aecpc->lastError = AEC_NULL_POINTER_ERROR;
return -1;
}
if (aecpc->initFlag != initCheck) {
aecpc->lastError = AEC_UNINITIALIZED_ERROR;
return -1;
}
// number of samples == 160 for SWB input
if (nrOfSamples != 80 && nrOfSamples != 160) {
aecpc->lastError = AEC_BAD_PARAMETER_ERROR;
return -1;
}
// Check for valid pointers based on sampling rate
if (aecpc->sampFreq == 32000 && nearendH == NULL) {
aecpc->lastError = AEC_NULL_POINTER_ERROR;
return -1;
}
if (msInSndCardBuf < 0) {
msInSndCardBuf = 0;
aecpc->lastError = AEC_BAD_PARAMETER_WARNING;
retVal = -1;
} else if (msInSndCardBuf > kMaxTrustedDelayMs) {
// The clamping is now done in ProcessExtended/Normal().
aecpc->lastError = AEC_BAD_PARAMETER_WARNING;
retVal = -1;
}
// This returns the value of aec->extended_filter_enabled.
if (WebRtcAec_delay_correction_enabled(aecpc->aec)) {
ProcessExtended(
aecpc, nearend, nearendH, out, outH, nrOfSamples, msInSndCardBuf, skew);
} else {
if (ProcessNormal(aecpc,
nearend,
nearendH,
out,
outH,
nrOfSamples,
msInSndCardBuf,
skew) != 0) {
retVal = -1;
}
}
#ifdef WEBRTC_AEC_DEBUG_DUMP
{
int16_t far_buf_size_ms = (int16_t)(WebRtcAec_system_delay(aecpc->aec) /
(sampMsNb * aecpc->rate_factor));
OpenDebugFiles(aecpc, &webrtc_aec_instance_count);
if (aecpc->bufFile) {
(void)fwrite(&far_buf_size_ms, 2, 1, aecpc->bufFile);
(void)fwrite(
&aecpc->knownDelay, sizeof(aecpc->knownDelay), 1, aecpc->delayFile);
}
}
#endif
return retVal;
}
static int ProcessNormal(Aec* aecpc,
const float* const* nearend,
int num_bands,
float* const* out,
int16_t nrOfSamples,
int16_t msInSndCardBuf,
int32_t skew) {
int retVal = 0;
short i;
short nBlocks10ms;
// Limit resampling to doubling/halving of signal
const float minSkewEst = -0.5f;
const float maxSkewEst = 1.0f;
msInSndCardBuf =
msInSndCardBuf > kMaxTrustedDelayMs ? kMaxTrustedDelayMs : msInSndCardBuf;
// TODO(andrew): we need to investigate if this +10 is really wanted.
msInSndCardBuf += 10;
aecpc->msInSndCardBuf = msInSndCardBuf;
if (aecpc->skewMode == kAecTrue) {
if (aecpc->skewFrCtr < 25) {
aecpc->skewFrCtr++;
} else {
retVal = WebRtcAec_GetSkew(aecpc->resampler, skew, &aecpc->skew);
if (retVal == -1) {
aecpc->skew = 0;
aecpc->lastError = AEC_BAD_PARAMETER_WARNING;
}
aecpc->skew /= aecpc->sampFactor * nrOfSamples;
if (aecpc->skew < 1.0e-3 && aecpc->skew > -1.0e-3) {
aecpc->resample = kAecFalse;
} else {
aecpc->resample = kAecTrue;
}
if (aecpc->skew < minSkewEst) {
aecpc->skew = minSkewEst;
} else if (aecpc->skew > maxSkewEst) {
aecpc->skew = maxSkewEst;
}
#ifdef WEBRTC_AEC_DEBUG_DUMP
(void)fwrite(&aecpc->skew, sizeof(aecpc->skew), 1, aecpc->skewFile);
#endif
}
}
nBlocks10ms = nrOfSamples / (FRAME_LEN * aecpc->rate_factor);
if (aecpc->startup_phase) {
for (i = 0; i < num_bands; ++i) {
// Only needed if they don't already point to the same place.
if (nearend[i] != out[i]) {
memcpy(out[i], nearend[i], sizeof(nearend[i][0]) * nrOfSamples);
}
}
// The AEC is in the start up mode
// AEC is disabled until the system delay is OK
// Mechanism to ensure that the system delay is reasonably stable.
if (aecpc->checkBuffSize) {
aecpc->checkBufSizeCtr++;
// Before we fill up the far-end buffer we require the system delay
// to be stable (+/-8 ms) compared to the first value. This
// comparison is made during the following 6 consecutive 10 ms
// blocks. If it seems to be stable then we start to fill up the
// far-end buffer.
if (aecpc->counter == 0) {
aecpc->firstVal = aecpc->msInSndCardBuf;
aecpc->sum = 0;
}
if (abs(aecpc->firstVal - aecpc->msInSndCardBuf) <
WEBRTC_SPL_MAX(0.2 * aecpc->msInSndCardBuf, sampMsNb)) {
aecpc->sum += aecpc->msInSndCardBuf;
aecpc->counter++;
} else {
aecpc->counter = 0;
}
if (aecpc->counter * nBlocks10ms >= 6) {
// The far-end buffer size is determined in partitions of
// PART_LEN samples. Use 75% of the average value of the system
// delay as buffer size to start with.
aecpc->bufSizeStart =
WEBRTC_SPL_MIN((3 * aecpc->sum * aecpc->rate_factor * 8) /
(4 * aecpc->counter * PART_LEN),
kMaxBufSizeStart);
// Buffer size has now been determined.
aecpc->checkBuffSize = 0;
}
if (aecpc->checkBufSizeCtr * nBlocks10ms > 50) {
// For really bad systems, don't disable the echo canceller for
// more than 0.5 sec.
aecpc->bufSizeStart = WEBRTC_SPL_MIN(
(aecpc->msInSndCardBuf * aecpc->rate_factor * 3) / 40,
kMaxBufSizeStart);
aecpc->checkBuffSize = 0;
}
}
// If |checkBuffSize| changed in the if-statement above.
if (!aecpc->checkBuffSize) {
// The system delay is now reasonably stable (or has been unstable
// for too long). When the far-end buffer is filled with
// approximately the same amount of data as reported by the system
// we end the startup phase.
int overhead_elements =
WebRtcAec_system_delay(aecpc->aec) / PART_LEN - aecpc->bufSizeStart;
if (overhead_elements == 0) {
// Enable the AEC
aecpc->startup_phase = 0;
} else if (overhead_elements > 0) {
// TODO(bjornv): Do we need a check on how much we actually
// moved the read pointer? It should always be possible to move
// the pointer |overhead_elements| since we have only added data
// to the buffer and no delay compensation nor AEC processing
// has been done.
WebRtcAec_MoveFarReadPtr(aecpc->aec, overhead_elements);
// Enable the AEC
aecpc->startup_phase = 0;
}
}
} else {
// AEC is enabled.
if (WebRtcAec_reported_delay_enabled(aecpc->aec)) {
EstBufDelayNormal(aecpc);
}
// Call the AEC.
// TODO(bjornv): Re-structure such that we don't have to pass
// |aecpc->knownDelay| as input. Change name to something like
// |system_buffer_diff|.
WebRtcAec_ProcessFrames(aecpc->aec,
nearend,
num_bands,
nrOfSamples,
aecpc->knownDelay,
out);
}
return retVal;
}
// only buffer L band for farend
int32_t WebRtcAec_BufferFarend(void* aecInst,
const float* farend,
int16_t nrOfSamples) {
Aec* aecpc = aecInst;
int newNrOfSamples = (int)nrOfSamples;
float new_farend[MAX_RESAMP_LEN];
const float* farend_ptr = farend;
if (farend == NULL) {
aecpc->lastError = AEC_NULL_POINTER_ERROR;
return -1;
}
if (aecpc->initFlag != initCheck) {
aecpc->lastError = AEC_UNINITIALIZED_ERROR;
return -1;
}
// number of samples == 160 for SWB input
if (nrOfSamples != 80 && nrOfSamples != 160) {
aecpc->lastError = AEC_BAD_PARAMETER_ERROR;
return -1;
}
if (aecpc->skewMode == kAecTrue && aecpc->resample == kAecTrue) {
// Resample and get a new number of samples
WebRtcAec_ResampleLinear(aecpc->resampler,
farend,
nrOfSamples,
aecpc->skew,
new_farend,
&newNrOfSamples);
farend_ptr = new_farend;
}
aecpc->farend_started = 1;
WebRtcAec_SetSystemDelay(aecpc->aec,
WebRtcAec_system_delay(aecpc->aec) + newNrOfSamples);
// Write the time-domain data to |far_pre_buf|.
WebRtc_WriteBuffer(aecpc->far_pre_buf, farend_ptr, (size_t)newNrOfSamples);
// Transform to frequency domain if we have enough data.
while (WebRtc_available_read(aecpc->far_pre_buf) >= PART_LEN2) {
// We have enough data to pass to the FFT, hence read PART_LEN2 samples.
{
float* ptmp = NULL;
float tmp[PART_LEN2];
WebRtc_ReadBuffer(aecpc->far_pre_buf, (void**)&ptmp, tmp, PART_LEN2);
WebRtcAec_BufferFarendPartition(aecpc->aec, ptmp);
#ifdef WEBRTC_AEC_DEBUG_DUMP
WebRtc_WriteBuffer(
WebRtcAec_far_time_buf(aecpc->aec), &ptmp[PART_LEN], 1);
#endif
}
// Rewind |far_pre_buf| PART_LEN samples for overlap before continuing.
WebRtc_MoveReadPtr(aecpc->far_pre_buf, -PART_LEN);
}
return 0;
}
static void ProcessExtended(Aec* self,
const float* const* near,
size_t num_bands,
float* const* out,
size_t num_samples,
int16_t reported_delay_ms,
int32_t skew) {
size_t i;
const int delay_diff_offset = kDelayDiffOffsetSamples;
#if defined(WEBRTC_UNTRUSTED_DELAY)
reported_delay_ms = kFixedDelayMs;
#else
// This is the usual mode where we trust the reported system delay values.
// Due to the longer filter, we no longer add 10 ms to the reported delay
// to reduce chance of non-causality. Instead we apply a minimum here to avoid
// issues with the read pointer jumping around needlessly.
reported_delay_ms = reported_delay_ms < kMinTrustedDelayMs
? kMinTrustedDelayMs
: reported_delay_ms;
// If the reported delay appears to be bogus, we attempt to recover by using
// the measured fixed delay values. We use >= here because higher layers
// may already clamp to this maximum value, and we would otherwise not
// detect it here.
reported_delay_ms = reported_delay_ms >= kMaxTrustedDelayMs
? kFixedDelayMs
: reported_delay_ms;
#endif
self->msInSndCardBuf = reported_delay_ms;
if (!self->farend_started) {
for (i = 0; i < num_bands; ++i) {
// Only needed if they don't already point to the same place.
if (near[i] != out[i]) {
memcpy(out[i], near[i], sizeof(near[i][0]) * num_samples);
}
}
return;
}
if (self->startup_phase) {
// In the extended mode, there isn't a startup "phase", just a special
// action on the first frame. In the trusted delay case, we'll take the
// current reported delay, unless it's less then our conservative
// measurement.
int startup_size_ms =
reported_delay_ms < kFixedDelayMs ? kFixedDelayMs : reported_delay_ms;
#if defined(WEBRTC_ANDROID) || defined(WEBRTC_GONK)
int target_delay = startup_size_ms * self->rate_factor * 8;
#else
// To avoid putting the AEC in a non-causal state we're being slightly
// conservative and scale by 2. On Android we use a fixed delay and
// therefore there is no need to scale the target_delay.
int target_delay = startup_size_ms * self->rate_factor * 8 / 2;
#endif
int overhead_elements =
(WebRtcAec_system_delay(self->aec) - target_delay) / PART_LEN;
WebRtcAec_MoveFarReadPtr(self->aec, overhead_elements);
self->startup_phase = 0;
}
EstBufDelayExtended(self);
{
// |delay_diff_offset| gives us the option to manually rewind the delay on
// very low delay platforms which can't be expressed purely through
// |reported_delay_ms|.
const int adjusted_known_delay =
WEBRTC_SPL_MAX(0, self->knownDelay + delay_diff_offset);
WebRtcAec_ProcessFrames(self->aec,
near,
num_bands,
num_samples,
adjusted_known_delay,
out);
}
}
int32_t WebRtcAec_Process(void* aecInst,
const float* const* nearend,
size_t num_bands,
float* const* out,
size_t nrOfSamples,
int16_t msInSndCardBuf,
int32_t skew) {
Aec* aecpc = aecInst;
int32_t retVal = 0;
if (out == NULL) {
return AEC_NULL_POINTER_ERROR;
}
if (aecpc->initFlag != initCheck) {
return AEC_UNINITIALIZED_ERROR;
}
// number of samples == 160 for SWB input
if (nrOfSamples != 80 && nrOfSamples != 160) {
return AEC_BAD_PARAMETER_ERROR;
}
if (msInSndCardBuf < 0) {
msInSndCardBuf = 0;
retVal = AEC_BAD_PARAMETER_WARNING;
} else if (msInSndCardBuf > kMaxTrustedDelayMs) {
// The clamping is now done in ProcessExtended/Normal().
retVal = AEC_BAD_PARAMETER_WARNING;
}
// This returns the value of aec->extended_filter_enabled.
if (WebRtcAec_extended_filter_enabled(aecpc->aec)) {
ProcessExtended(aecpc,
nearend,
num_bands,
out,
nrOfSamples,
msInSndCardBuf,
skew);
} else {
retVal = ProcessNormal(aecpc,
nearend,
num_bands,
out,
nrOfSamples,
msInSndCardBuf,
skew);
}
#ifdef WEBRTC_AEC_DEBUG_DUMP
{
int16_t far_buf_size_ms = (int16_t)(WebRtcAec_system_delay(aecpc->aec) /
(sampMsNb * aecpc->rate_factor));
OpenDebugFiles(aecpc, &webrtc_aec_instance_count);
if (aecpc->bufFile) {
(void)fwrite(&far_buf_size_ms, 2, 1, aecpc->bufFile);
(void)fwrite(
&aecpc->knownDelay, sizeof(aecpc->knownDelay), 1, aecpc->delayFile);
}
}
#endif
return retVal;
}
