static int piix4_setup_aux(struct pci_dev *PIIX4_dev,
const struct pci_device_id *id,
unsigned short base_reg_addr)
{
/* Set up auxiliary SMBus controllers found on some
* AMD chipsets e.g. SP5100 (SB700 derivative) */
unsigned short piix4_smba;
/* Read address of auxiliary SMBus controller */
pci_read_config_word(PIIX4_dev, base_reg_addr, &piix4_smba);
if ((piix4_smba & 1) == 0) {
dev_dbg(&PIIX4_dev->dev,
"Auxiliary SMBus controller not enabled\n");
return -ENODEV;
}
piix4_smba &= 0xfff0;
if (piix4_smba == 0) {
dev_dbg(&PIIX4_dev->dev,
"Auxiliary SMBus base address uninitialized\n");
return -ENODEV;
}
if (acpi_check_region(piix4_smba, SMBIOSIZE, piix4_driver.name))
return -ENODEV;
if (!request_region(piix4_smba, SMBIOSIZE, piix4_driver.name)) {
dev_err(&PIIX4_dev->dev, "Auxiliary SMBus region 0x%x "
"already in use!\n", piix4_smba);
return -EBUSY;
}
dev_info(&PIIX4_dev->dev,
"Auxiliary SMBus Host Controller at 0x%x\n",
piix4_smba);
return piix4_smba;
}
static int __devinit amd756_probe(struct pci_dev *pdev,
const struct pci_device_id *id)
{
int nforce = (id->driver_data == NFORCE);
int error;
u8 temp;
if (amd756_ioport) {
dev_err(&pdev->dev, "Only one device supported "
"(you have a strange motherboard, btw)\n");
return -ENODEV;
}
if (nforce) {
if (PCI_FUNC(pdev->devfn) != 1)
return -ENODEV;
pci_read_config_word(pdev, SMBBANFORCE, &amd756_ioport);
amd756_ioport &= 0xfffc;
} else { /* amd */
if (PCI_FUNC(pdev->devfn) != 3)
return -ENODEV;
pci_read_config_byte(pdev, SMBGCFG, &temp);
if ((temp & 128) == 0) {
dev_err(&pdev->dev,
"Error: SMBus controller I/O not enabled!\n");
return -ENODEV;
}
/* Determine the address of the SMBus areas */
/* Technically it is a dword but... */
pci_read_config_word(pdev, SMBBA, &amd756_ioport);
amd756_ioport &= 0xff00;
amd756_ioport += SMB_ADDR_OFFSET;
}
error = acpi_check_region(amd756_ioport, SMB_IOSIZE,
amd756_driver.name);
if (error)
return -ENODEV;
if (!request_region(amd756_ioport, SMB_IOSIZE, amd756_driver.name)) {
dev_err(&pdev->dev, "SMB region 0x%x already in use!\n",
amd756_ioport);
return -ENODEV;
}
pci_read_config_byte(pdev, SMBREV, &temp);
dev_dbg(&pdev->dev, "SMBREV = 0x%X\n", temp);
dev_dbg(&pdev->dev, "AMD756_smba = 0x%X\n", amd756_ioport);
/* set up the sysfs linkage to our parent device */
amd756_smbus.dev.parent = &pdev->dev;
snprintf(amd756_smbus.name, sizeof(amd756_smbus.name),
"SMBus %s adapter at %04x", chipname[id->driver_data],
amd756_ioport);
error = i2c_add_adapter(&amd756_smbus);
if (error) {
dev_err(&pdev->dev,
"Adapter registration failed, module not inserted\n");
goto out_err;
}
return 0;
out_err:
release_region(amd756_ioport, SMB_IOSIZE);
return error;
}
static int piix4_setup_sb800(struct pci_dev *PIIX4_dev,
const struct pci_device_id *id, u8 aux)
{
unsigned short piix4_smba;
unsigned short smba_idx = 0xcd6;
u8 smba_en_lo, smba_en_hi, smb_en, smb_en_status;
u8 i2ccfg, i2ccfg_offset = 0x10;
/* SB800 and later SMBus does not support forcing address */
if (force || force_addr) {
dev_err(&PIIX4_dev->dev, "SMBus does not support "
"forcing address!\n");
return -EINVAL;
}
/* Determine the address of the SMBus areas */
if ((PIIX4_dev->vendor == PCI_VENDOR_ID_AMD &&
PIIX4_dev->device == PCI_DEVICE_ID_AMD_HUDSON2_SMBUS &&
PIIX4_dev->revision >= 0x41) ||
(PIIX4_dev->vendor == PCI_VENDOR_ID_AMD &&
PIIX4_dev->device == 0x790b &&
PIIX4_dev->revision >= 0x49))
smb_en = 0x00;
else
smb_en = (aux) ? 0x28 : 0x2c;
if (!request_region(smba_idx, 2, "smba_idx")) {
dev_err(&PIIX4_dev->dev, "SMBus base address index region "
"0x%x already in use!\n", smba_idx);
return -EBUSY;
}
outb_p(smb_en, smba_idx);
smba_en_lo = inb_p(smba_idx + 1);
outb_p(smb_en + 1, smba_idx);
smba_en_hi = inb_p(smba_idx + 1);
release_region(smba_idx, 2);
if (!smb_en) {
smb_en_status = smba_en_lo & 0x10;
piix4_smba = smba_en_hi << 8;
if (aux)
piix4_smba |= 0x20;
} else {
smb_en_status = smba_en_lo & 0x01;
piix4_smba = ((smba_en_hi << 8) | smba_en_lo) & 0xffe0;
}
if (!smb_en_status) {
dev_err(&PIIX4_dev->dev,
"Host SMBus controller not enabled!\n");
return -ENODEV;
}
if (acpi_check_region(piix4_smba, SMBIOSIZE, piix4_driver.name))
return -ENODEV;
if (!request_region(piix4_smba, SMBIOSIZE, piix4_driver.name)) {
dev_err(&PIIX4_dev->dev, "SMBus region 0x%x already in use!\n",
piix4_smba);
return -EBUSY;
}
/* Aux SMBus does not support IRQ information */
if (aux) {
dev_info(&PIIX4_dev->dev,
"SMBus Host Controller at 0x%x\n", piix4_smba);
return piix4_smba;
}
/* Request the SMBus I2C bus config region */
if (!request_region(piix4_smba + i2ccfg_offset, 1, "i2ccfg")) {
dev_err(&PIIX4_dev->dev, "SMBus I2C bus config region "
"0x%x already in use!\n", piix4_smba + i2ccfg_offset);
release_region(piix4_smba, SMBIOSIZE);
return -EBUSY;
}
i2ccfg = inb_p(piix4_smba + i2ccfg_offset);
release_region(piix4_smba + i2ccfg_offset, 1);
if (i2ccfg & 1)
dev_dbg(&PIIX4_dev->dev, "Using IRQ for SMBus.\n");
else
dev_dbg(&PIIX4_dev->dev, "Using SMI# for SMBus.\n");
dev_info(&PIIX4_dev->dev,
"SMBus Host Controller at 0x%x, revision %d\n",
piix4_smba, i2ccfg >> 4);
return piix4_smba;
}
static int piix4_setup(struct pci_dev *PIIX4_dev,
const struct pci_device_id *id)
{
unsigned char temp;
unsigned short piix4_smba;
if ((PIIX4_dev->vendor == PCI_VENDOR_ID_SERVERWORKS) &&
(PIIX4_dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5))
srvrworks_csb5_delay = 1;
/* On some motherboards, it was reported that accessing the SMBus
caused severe hardware problems */
if (dmi_check_system(piix4_dmi_blacklist)) {
dev_err(&PIIX4_dev->dev,
"Accessing the SMBus on this system is unsafe!\n");
return -EPERM;
}
/* Don't access SMBus on IBM systems which get corrupted eeproms */
if (dmi_check_system(piix4_dmi_ibm) &&
PIIX4_dev->vendor == PCI_VENDOR_ID_INTEL) {
dev_err(&PIIX4_dev->dev, "IBM system detected; this module "
"may corrupt your serial eeprom! Refusing to load "
"module!\n");
return -EPERM;
}
/* Determine the address of the SMBus areas */
if (force_addr) {
piix4_smba = force_addr & 0xfff0;
force = 0;
} else {
pci_read_config_word(PIIX4_dev, SMBBA, &piix4_smba);
piix4_smba &= 0xfff0;
if(piix4_smba == 0) {
dev_err(&PIIX4_dev->dev, "SMBus base address "
"uninitialized - upgrade BIOS or use "
"force_addr=0xaddr\n");
return -ENODEV;
}
}
if (acpi_check_region(piix4_smba, SMBIOSIZE, piix4_driver.name))
return -ENODEV;
if (!request_region(piix4_smba, SMBIOSIZE, piix4_driver.name)) {
dev_err(&PIIX4_dev->dev, "SMBus region 0x%x already in use!\n",
piix4_smba);
return -EBUSY;
}
pci_read_config_byte(PIIX4_dev, SMBHSTCFG, &temp);
/* If force_addr is set, we program the new address here. Just to make
sure, we disable the PIIX4 first. */
if (force_addr) {
pci_write_config_byte(PIIX4_dev, SMBHSTCFG, temp & 0xfe);
pci_write_config_word(PIIX4_dev, SMBBA, piix4_smba);
pci_write_config_byte(PIIX4_dev, SMBHSTCFG, temp | 0x01);
dev_info(&PIIX4_dev->dev, "WARNING: SMBus interface set to "
"new address %04x!\n", piix4_smba);
} else if ((temp & 1) == 0) {
if (force) {
/* This should never need to be done, but has been
* noted that many Dell machines have the SMBus
* interface on the PIIX4 disabled!? NOTE: This assumes
* I/O space and other allocations WERE done by the
* Bios! Don't complain if your hardware does weird
* things after enabling this. :') Check for Bios
* updates before resorting to this.
*/
pci_write_config_byte(PIIX4_dev, SMBHSTCFG,
temp | 1);
dev_notice(&PIIX4_dev->dev,
"WARNING: SMBus interface has been FORCEFULLY ENABLED!\n");
} else {
dev_err(&PIIX4_dev->dev,
"Host SMBus controller not enabled!\n");
release_region(piix4_smba, SMBIOSIZE);
return -ENODEV;
}
}
if (((temp & 0x0E) == 8) || ((temp & 0x0E) == 2))
dev_dbg(&PIIX4_dev->dev, "Using Interrupt 9 for SMBus.\n");
else if ((temp & 0x0E) == 0)
dev_dbg(&PIIX4_dev->dev, "Using Interrupt SMI# for SMBus.\n");
else
dev_err(&PIIX4_dev->dev, "Illegal Interrupt configuration "
"(or code out of date)!\n");
pci_read_config_byte(PIIX4_dev, SMBREV, &temp);
dev_info(&PIIX4_dev->dev,
"SMBus Host Controller at 0x%x, revision %d\n",
piix4_smba, temp);
return piix4_smba;
}
static int __devinit piix4_setup_sb800(struct pci_dev *PIIX4_dev,
const struct pci_device_id *id)
{
unsigned short smba_idx = 0xcd6;
u8 smba_en_lo, smba_en_hi, i2ccfg, i2ccfg_offset = 0x10, smb_en = 0x2c;
/* SB800 and later SMBus does not support forcing address */
if (force || force_addr) {
dev_err(&PIIX4_dev->dev, "SMBus does not support "
"forcing address!\n");
return -EINVAL;
}
/* Determine the address of the SMBus areas */
if (!request_region(smba_idx, 2, "smba_idx")) {
dev_err(&PIIX4_dev->dev, "SMBus base address index region "
"0x%x already in use!\n", smba_idx);
return -EBUSY;
}
outb_p(smb_en, smba_idx);
smba_en_lo = inb_p(smba_idx + 1);
outb_p(smb_en + 1, smba_idx);
smba_en_hi = inb_p(smba_idx + 1);
release_region(smba_idx, 2);
if ((smba_en_lo & 1) == 0) {
dev_err(&PIIX4_dev->dev,
"Host SMBus controller not enabled!\n");
return -ENODEV;
}
piix4_smba = ((smba_en_hi << 8) | smba_en_lo) & 0xffe0;
if (acpi_check_region(piix4_smba, SMBIOSIZE, piix4_driver.name))
return -ENODEV;
if (!request_region(piix4_smba, SMBIOSIZE, piix4_driver.name)) {
dev_err(&PIIX4_dev->dev, "SMBus region 0x%x already in use!\n",
piix4_smba);
return -EBUSY;
}
/* Request the SMBus I2C bus config region */
if (!request_region(piix4_smba + i2ccfg_offset, 1, "i2ccfg")) {
dev_err(&PIIX4_dev->dev, "SMBus I2C bus config region "
"0x%x already in use!\n", piix4_smba + i2ccfg_offset);
release_region(piix4_smba, SMBIOSIZE);
piix4_smba = 0;
return -EBUSY;
}
i2ccfg = inb_p(piix4_smba + i2ccfg_offset);
release_region(piix4_smba + i2ccfg_offset, 1);
if (i2ccfg & 1)
dev_dbg(&PIIX4_dev->dev, "Using IRQ for SMBus.\n");
else
dev_dbg(&PIIX4_dev->dev, "Using SMI# for SMBus.\n");
dev_info(&PIIX4_dev->dev,
"SMBus Host Controller at 0x%x, revision %d\n",
piix4_smba, i2ccfg >> 4);
return 0;
}
static int __devinit ali1535_setup(struct pci_dev *dev)
{
int retval = -ENODEV;
unsigned char temp;
/* Check the following things:
- SMB I/O address is initialized
- Device is enabled
- We can use the addresses
*/
/* Determine the address of the SMBus area */
pci_read_config_word(dev, SMBBA, &ali1535_smba);
ali1535_smba &= (0xffff & ~(ALI1535_SMB_IOSIZE - 1));
if (ali1535_smba == 0) {
dev_warn(&dev->dev,
"ALI1535_smb region uninitialized - upgrade BIOS?\n");
goto exit;
}
retval = acpi_check_region(ali1535_smba, ALI1535_SMB_IOSIZE,
ali1535_driver.name);
if (retval)
goto exit;
if (!request_region(ali1535_smba, ALI1535_SMB_IOSIZE,
ali1535_driver.name)) {
dev_err(&dev->dev, "ALI1535_smb region 0x%x already in use!\n",
ali1535_smba);
goto exit;
}
/* check if whole device is enabled */
pci_read_config_byte(dev, SMBCFG, &temp);
if ((temp & ALI1535_SMBIO_EN) == 0) {
dev_err(&dev->dev, "SMB device not enabled - upgrade BIOS?\n");
goto exit_free;
}
/* Is SMB Host controller enabled? */
pci_read_config_byte(dev, SMBHSTCFG, &temp);
if ((temp & 1) == 0) {
dev_err(&dev->dev, "SMBus controller not enabled - upgrade BIOS?\n");
goto exit_free;
}
/* set SMB clock to 74KHz as recommended in data sheet */
pci_write_config_byte(dev, SMBCLK, 0x20);
/*
The interrupt routing for SMB is set up in register 0x77 in the
1533 ISA Bridge device, NOT in the 7101 device.
Don't bother with finding the 1533 device and reading the register.
if ((....... & 0x0F) == 1)
dev_dbg(&dev->dev, "ALI1535 using Interrupt 9 for SMBus.\n");
*/
pci_read_config_byte(dev, SMBREV, &temp);
dev_dbg(&dev->dev, "SMBREV = 0x%X\n", temp);
dev_dbg(&dev->dev, "ALI1535_smba = 0x%X\n", ali1535_smba);
retval = 0;
exit:
return retval;
exit_free:
release_region(ali1535_smba, ALI1535_SMB_IOSIZE);
return retval;
}
static int ali15x3_setup(struct pci_dev *ALI15X3_dev)
{
u16 a;
unsigned char temp;
/* Check the following things:
- SMB I/O address is initialized
- Device is enabled
- We can use the addresses
*/
/* Unlock the register.
The data sheet says that the address registers are read-only
if the lock bits are 1, but in fact the address registers
are zero unless you clear the lock bits.
*/
pci_read_config_byte(ALI15X3_dev, SMBATPC, &temp);
if (temp & ALI15X3_LOCK) {
temp &= ~ALI15X3_LOCK;
pci_write_config_byte(ALI15X3_dev, SMBATPC, temp);
}
/* Determine the address of the SMBus area */
pci_read_config_word(ALI15X3_dev, SMBBA, &ali15x3_smba);
ali15x3_smba &= (0xffff & ~(ALI15X3_SMB_IOSIZE - 1));
if (ali15x3_smba == 0 && force_addr == 0) {
dev_err(&ALI15X3_dev->dev, "ALI15X3_smb region uninitialized "
"- upgrade BIOS or use force_addr=0xaddr\n");
return -ENODEV;
}
if(force_addr)
ali15x3_smba = force_addr & ~(ALI15X3_SMB_IOSIZE - 1);
if (acpi_check_region(ali15x3_smba, ALI15X3_SMB_IOSIZE,
ali15x3_driver.name))
return -EBUSY;
if (!request_region(ali15x3_smba, ALI15X3_SMB_IOSIZE,
ali15x3_driver.name)) {
dev_err(&ALI15X3_dev->dev,
"ALI15X3_smb region 0x%x already in use!\n",
ali15x3_smba);
return -ENODEV;
}
if(force_addr) {
dev_info(&ALI15X3_dev->dev, "forcing ISA address 0x%04X\n",
ali15x3_smba);
if (PCIBIOS_SUCCESSFUL != pci_write_config_word(ALI15X3_dev,
SMBBA,
ali15x3_smba))
goto error;
if (PCIBIOS_SUCCESSFUL != pci_read_config_word(ALI15X3_dev,
SMBBA, &a))
goto error;
if ((a & ~(ALI15X3_SMB_IOSIZE - 1)) != ali15x3_smba) {
/* make sure it works */
dev_err(&ALI15X3_dev->dev,
"force address failed - not supported?\n");
goto error;
}
}
/* check if whole device is enabled */
pci_read_config_byte(ALI15X3_dev, SMBCOM, &temp);
if ((temp & 1) == 0) {
dev_info(&ALI15X3_dev->dev, "enabling SMBus device\n");
pci_write_config_byte(ALI15X3_dev, SMBCOM, temp | 0x01);
}
/* Is SMB Host controller enabled? */
pci_read_config_byte(ALI15X3_dev, SMBHSTCFG, &temp);
if ((temp & 1) == 0) {
dev_info(&ALI15X3_dev->dev, "enabling SMBus controller\n");
pci_write_config_byte(ALI15X3_dev, SMBHSTCFG, temp | 0x01);
}
/* set SMB clock to 74KHz as recommended in data sheet */
pci_write_config_byte(ALI15X3_dev, SMBCLK, 0x20);
/*
The interrupt routing for SMB is set up in register 0x77 in the
1533 ISA Bridge device, NOT in the 7101 device.
Don't bother with finding the 1533 device and reading the register.
if ((....... & 0x0F) == 1)
dev_dbg(&ALI15X3_dev->dev, "ALI15X3 using Interrupt 9 for SMBus.\n");
*/
pci_read_config_byte(ALI15X3_dev, SMBREV, &temp);
dev_dbg(&ALI15X3_dev->dev, "SMBREV = 0x%X\n", temp);
dev_dbg(&ALI15X3_dev->dev, "iALI15X3_smba = 0x%X\n", ali15x3_smba);
return 0;
error:
release_region(ali15x3_smba, ALI15X3_SMB_IOSIZE);
return -ENODEV;
}
static int sis5595_setup(struct pci_dev *SIS5595_dev)
{
u16 a;
u8 val;
int *i;
int retval;
/* Look for imposters */
for (i = blacklist; *i != 0; i++) {
struct pci_dev *dev;
dev = pci_get_device(PCI_VENDOR_ID_SI, *i, NULL);
if (dev) {
dev_err(&SIS5595_dev->dev, "Looked for SIS5595 but found unsupported device %.4x\n", *i);
pci_dev_put(dev);
return -ENODEV;
}
}
/* Determine the address of the SMBus areas */
pci_read_config_word(SIS5595_dev, ACPI_BASE, &sis5595_base);
if (sis5595_base == 0 && force_addr == 0) {
dev_err(&SIS5595_dev->dev, "ACPI base address uninitialized - upgrade BIOS or use force_addr=0xaddr\n");
return -ENODEV;
}
if (force_addr)
sis5595_base = force_addr & ~(SIS5595_EXTENT - 1);
dev_dbg(&SIS5595_dev->dev, "ACPI Base address: %04x\n", sis5595_base);
/* NB: We grab just the two SMBus registers here, but this may still
* interfere with ACPI :-( */
retval = acpi_check_region(sis5595_base + SMB_INDEX, 2,
sis5595_driver.name);
if (retval)
return retval;
if (!request_region(sis5595_base + SMB_INDEX, 2,
sis5595_driver.name)) {
dev_err(&SIS5595_dev->dev, "SMBus registers 0x%04x-0x%04x already in use!\n",
sis5595_base + SMB_INDEX, sis5595_base + SMB_INDEX + 1);
return -ENODEV;
}
if (force_addr) {
dev_info(&SIS5595_dev->dev, "forcing ISA address 0x%04X\n", sis5595_base);
if (pci_write_config_word(SIS5595_dev, ACPI_BASE, sis5595_base)
!= PCIBIOS_SUCCESSFUL)
goto error;
if (pci_read_config_word(SIS5595_dev, ACPI_BASE, &a)
!= PCIBIOS_SUCCESSFUL)
goto error;
if ((a & ~(SIS5595_EXTENT - 1)) != sis5595_base) {
/* doesn't work for some chips! */
dev_err(&SIS5595_dev->dev, "force address failed - not supported?\n");
goto error;
}
}
if (pci_read_config_byte(SIS5595_dev, SIS5595_ENABLE_REG, &val)
!= PCIBIOS_SUCCESSFUL)
goto error;
if ((val & 0x80) == 0) {
dev_info(&SIS5595_dev->dev, "enabling ACPI\n");
if (pci_write_config_byte(SIS5595_dev, SIS5595_ENABLE_REG, val | 0x80)
!= PCIBIOS_SUCCESSFUL)
goto error;
if (pci_read_config_byte(SIS5595_dev, SIS5595_ENABLE_REG, &val)
!= PCIBIOS_SUCCESSFUL)
goto error;
if ((val & 0x80) == 0) {
/* doesn't work for some chips? */
dev_err(&SIS5595_dev->dev, "ACPI enable failed - not supported?\n");
goto error;
}
}
/* Everything is happy */
return 0;
error:
release_region(sis5595_base + SMB_INDEX, 2);
return -ENODEV;
}
