void atyfb_fillrect(struct fb_info *info, const struct fb_fillrect *rect)
{
struct atyfb_par *par = (struct atyfb_par *) info->par;
u32 color = rect->color, dx = rect->dx, width = rect->width, rotation = 0;
if (par->asleep)
return;
if (!rect->width || !rect->height)
return;
if (!par->accel_flags) {
cfb_fillrect(info, rect);
return;
}
color |= (rect->color << 8);
color |= (rect->color << 16);
if (info->var.bits_per_pixel == 24) {
/* In 24 bpp, the engine is in 8 bpp - this requires that all */
/* horizontal coordinates and widths must be adjusted */
dx *= 3;
width *= 3;
rotation = rotation24bpp(dx, DST_X_LEFT_TO_RIGHT);
}
wait_for_fifo(3, par);
aty_st_le32(DP_FRGD_CLR, color, par);
aty_st_le32(DP_SRC,
BKGD_SRC_BKGD_CLR | FRGD_SRC_FRGD_CLR | MONO_SRC_ONE,
par);
aty_st_le32(DST_CNTL,
DST_LAST_PEL | DST_Y_TOP_TO_BOTTOM |
DST_X_LEFT_TO_RIGHT | rotation, par);
draw_rect(dx, rect->dy, width, rect->height, par);
}
static inline void draw_rect(s16 x, s16 y, u16 width, u16 height,
struct atyfb_par *par)
{
/* perform rectangle fill */
wait_for_fifo(2, par);
aty_st_le32(DST_Y_X, (x << 16) | y, par);
aty_st_le32(DST_HEIGHT_WIDTH, (width << 16) | height, par);
par->blitter_may_be_busy = 1;
}
static void reset_GTC_3D_engine(const struct fb_info_aty *info)
{
aty_st_le32(SCALE_3D_CNTL, 0xc0, info);
mdelay(GTC_3D_RESET_DELAY);
aty_st_le32(SETUP_CNTL, 0x00, info);
mdelay(GTC_3D_RESET_DELAY);
aty_st_le32(SCALE_3D_CNTL, 0x00, info);
mdelay(GTC_3D_RESET_DELAY);
}
static inline void draw_rect(s16 x, s16 y, u16 width, u16 height,
struct fb_info_aty *info)
{
/* perform rectangle fill */
wait_for_fifo(2, info);
aty_st_le32(DST_Y_X, (x << 16) | y, info);
aty_st_le32(DST_HEIGHT_WIDTH, (width << 16) | height, info);
info->blitter_may_be_busy = 1;
}
static void reset_GTC_3D_engine(const struct atyfb_par *par)
{
aty_st_le32(SCALE_3D_CNTL, 0xc0, par);
mdelay(GTC_3D_RESET_DELAY);
aty_st_le32(SETUP_CNTL, 0x00, par);
mdelay(GTC_3D_RESET_DELAY);
aty_st_le32(SCALE_3D_CNTL, 0x00, par);
mdelay(GTC_3D_RESET_DELAY);
}
static int atyfb_cursor(struct fb_info *info, struct fb_cursor *cursor)
{
struct atyfb_par *par = (struct atyfb_par *) info->par;
u16 xoff, yoff;
int x, y, h;
#ifdef __sparc__
if (par->mmaped)
return -EPERM;
#endif
if (par->asleep)
return -EPERM;
wait_for_fifo(1, par);
if (cursor->enable)
aty_st_le32(GEN_TEST_CNTL, aty_ld_le32(GEN_TEST_CNTL, par)
| HWCURSOR_ENABLE, par);
else
aty_st_le32(GEN_TEST_CNTL, aty_ld_le32(GEN_TEST_CNTL, par)
& ~HWCURSOR_ENABLE, par);
/* set position */
if (cursor->set & FB_CUR_SETPOS) {
x = cursor->image.dx - cursor->hot.x - info->var.xoffset;
if (x < 0) {
xoff = -x;
x = 0;
} else {
xoff = 0;
}
y = cursor->image.dy - cursor->hot.y - info->var.yoffset;
if (y < 0) {
yoff = -y;
y = 0;
} else {
yoff = 0;
}
h = cursor->image.height;
/*
* In doublescan mode, the cursor location
* and heigh also needs to be doubled.
*/
if (par->crtc.gen_cntl & CRTC_DBL_SCAN_EN) {
y<<=1;
h<<=1;
}
wait_for_fifo(3, par);
aty_st_le32(CUR_OFFSET, (info->fix.smem_len >> 3) + (yoff << 1), par);
aty_st_le32(CUR_HORZ_VERT_OFF,
((u32) (64 - h + yoff) << 16) | xoff, par);
aty_st_le32(CUR_HORZ_VERT_POSN, ((u32) y << 16) | x, par);
}
void aty_reset_engine(const struct atyfb_par *par)
{
/* reset engine */
aty_st_le32(GEN_TEST_CNTL,
aty_ld_le32(GEN_TEST_CNTL, par) & ~GUI_ENGINE_ENABLE, par);
/* enable engine */
aty_st_le32(GEN_TEST_CNTL,
aty_ld_le32(GEN_TEST_CNTL, par) | GUI_ENGINE_ENABLE, par);
/* ensure engine is not locked up by clearing any FIFO or */
/* HOST errors */
aty_st_le32(BUS_CNTL,
aty_ld_le32(BUS_CNTL, par) | BUS_HOST_ERR_ACK | BUS_FIFO_ERR_ACK, par);
}
static int aty_set_dac_unsupported(const struct fb_info *info,
const union aty_pll *pll, u32 bpp,
u32 accel)
{
struct atyfb_par *par = (struct atyfb_par *) info->par;
aty_st_le32(BUS_CNTL, 0x890e20f1, par);
aty_st_le32(DAC_CNTL, 0x47052100, par);
/* new in 2.2.3p1 from Geert. ???????? */
aty_st_le32(BUS_CNTL, 0x590e10ff, par);
aty_st_le32(DAC_CNTL, 0x47012100, par);
return 0;
}
void aty_reset_engine(const struct atyfb_par *par)
{
aty_st_le32(GEN_TEST_CNTL,
aty_ld_le32(GEN_TEST_CNTL, par) &
~(GUI_ENGINE_ENABLE | HWCURSOR_ENABLE), par);
aty_st_le32(GEN_TEST_CNTL,
aty_ld_le32(GEN_TEST_CNTL, par) | GUI_ENGINE_ENABLE, par);
aty_st_le32(BUS_CNTL,
aty_ld_le32(BUS_CNTL, par) | BUS_HOST_ERR_ACK | BUS_FIFO_ERR_ACK, par);
}
void atyfb_copyarea(struct fb_info *info, const struct fb_copyarea *area)
{
struct atyfb_par *par = (struct atyfb_par *) info->par;
u32 dy = area->dy, sy = area->sy, direction = DST_LAST_PEL;
u32 sx = area->sx, dx = area->dx, width = area->width, rotation = 0;
if (par->asleep)
return;
if (!area->width || !area->height)
return;
if (!par->accel_flags) {
cfb_copyarea(info, area);
return;
}
if (info->var.bits_per_pixel == 24) {
/* In 24 bpp, the engine is in 8 bpp - this requires that all */
/* horizontal coordinates and widths must be adjusted */
sx *= 3;
dx *= 3;
width *= 3;
}
if (area->sy < area->dy) {
dy += area->height - 1;
sy += area->height - 1;
} else
direction |= DST_Y_TOP_TO_BOTTOM;
if (sx < dx) {
dx += width - 1;
sx += width - 1;
} else
direction |= DST_X_LEFT_TO_RIGHT;
if (info->var.bits_per_pixel == 24) {
rotation = rotation24bpp(dx, direction);
}
wait_for_fifo(4, par);
aty_st_le32(DP_SRC, FRGD_SRC_BLIT, par);
aty_st_le32(SRC_Y_X, (sx << 16) | sy, par);
aty_st_le32(SRC_HEIGHT1_WIDTH1, (width << 16) | area->height, par);
aty_st_le32(DST_CNTL, direction | rotation, par);
draw_rect(dx, dy, width, area->height, par);
}
static int aty_set_dac_ATT21C498(const struct fb_info *info,
const union aty_pll *pll, u32 bpp,
u32 accel)
{
struct atyfb_par *par = (struct atyfb_par *) info->par;
u32 dotClock;
int muxmode = 0;
int DACMask = 0;
dotClock = 100000000 / pll->ics2595.period_in_ps;
switch (bpp) {
case 8:
if (dotClock > 8000) {
DACMask = 0x24;
muxmode = 1;
} else
DACMask = 0x04;
break;
case 15:
DACMask = 0x16;
break;
case 16:
DACMask = 0x36;
break;
case 24:
DACMask = 0xE6;
break;
case 32:
DACMask = 0xE6;
break;
}
if (1 /* info->mach64DAC8Bit */ )
DACMask |= 0x02;
aty_dac_waste4(par);
aty_st_8(DAC_REGS + 2, DACMask, par);
aty_st_le32(BUS_CNTL, 0x890e20f1, par);
aty_st_le32(DAC_CNTL, 0x00072000, par);
return muxmode;
}
void GGI_ati_mach64_gcchanged(struct ggi_visual *vis, int mask)
{
struct ggi_gc *gc;
struct ati_mach64_priv *priv;
priv = ATI_MACH64_PRIV(vis);
gc = LIBGGI_GC(vis);
/* Set new foreground colour if it's changed */
if (gc->fg_color != priv->oldfgcol) {
wait_for_fifo(1, priv);
aty_st_le32(DP_FRGD_CLR, (unsigned) gc->fg_color, priv);
priv->oldfgcol = gc->fg_color;
};
/* Set new background colour if it's changed */
if (gc->bg_color != priv->oldbgcol) {
wait_for_fifo(1, priv);
aty_st_le32(DP_BKGD_CLR, (unsigned) gc->bg_color, priv);
priv->oldbgcol = gc->bg_color;
};
/* Set new horizontal clipping if it's changed */
if ((gc->cliptl.x != priv->oldtl.x)
|| (gc->clipbr.x != priv->oldbr.x)) {
wait_for_fifo(1, priv);
aty_st_le32(SC_LEFT_RIGHT,
(unsigned)gc->clipbr.x << 16 | gc->cliptl.x,
priv);
priv->oldtl.x = gc->cliptl.x;
priv->oldbr.x = gc->clipbr.x;
};
/* Set new vertical clipping if it's changed */
if ((gc->cliptl.y != priv->oldtl.y)
|| (gc->clipbr.y != priv->oldbr.y)) {
wait_for_fifo(1, priv);
aty_st_le32(SC_TOP_BOTTOM,
(unsigned)gc->clipbr.y << 16 | gc->cliptl.y,
priv);
priv->oldtl.y = gc->cliptl.y;
priv->oldbr.y = gc->clipbr.y;
};
vis->accelactive = 1;
}
void aty_rectfill(int dstx, int dsty, u_int width, u_int height, u_int color,
struct fb_info_aty *info)
{
if (!width || !height)
return;
if (info->current_par.crtc.bpp == 24) {
/* In 24 bpp, the engine is in 8 bpp - this requires that all */
/* horizontal coordinates and widths must be adjusted */
dstx *= 3;
width *= 3;
}
wait_for_fifo(3, info);
aty_st_le32(DP_FRGD_CLR, color, info);
aty_st_le32(DP_SRC, BKGD_SRC_BKGD_CLR | FRGD_SRC_FRGD_CLR | MONO_SRC_ONE,
info);
aty_st_le32(DST_CNTL, DST_LAST_PEL | DST_Y_TOP_TO_BOTTOM |
DST_X_LEFT_TO_RIGHT, info);
draw_rect(dstx, dsty, width, height, info);
}
static inline void aty_rectcopy(int srcx, int srcy, int dstx, int dsty,
u_int width, u_int height,
struct fb_info_aty *info)
{
u32 direction = DST_LAST_PEL;
u32 pitch_value;
if (!width || !height)
return;
pitch_value = info->current_par.crtc.vxres;
if (info->current_par.crtc.bpp == 24) {
/* In 24 bpp, the engine is in 8 bpp - this requires that all */
/* horizontal coordinates and widths must be adjusted */
pitch_value *= 3;
srcx *= 3;
dstx *= 3;
width *= 3;
}
if (srcy < dsty) {
dsty += height - 1;
srcy += height - 1;
} else
direction |= DST_Y_TOP_TO_BOTTOM;
if (srcx < dstx) {
dstx += width - 1;
srcx += width - 1;
} else
direction |= DST_X_LEFT_TO_RIGHT;
wait_for_fifo(4, info);
aty_st_le32(DP_SRC, FRGD_SRC_BLIT, info);
aty_st_le32(SRC_Y_X, (srcx << 16) | srcy, info);
aty_st_le32(SRC_HEIGHT1_WIDTH1, (width << 16) | height, info);
aty_st_le32(DST_CNTL, direction, info);
draw_rect(dstx, dsty, width, height, info);
}
void atyfb_fillrect(struct fb_info *info, const struct fb_fillrect *rect)
{
struct atyfb_par *par = (struct atyfb_par *) info->par;
u32 color, dx = rect->dx, width = rect->width, rotation = 0;
if (par->asleep)
return;
if (!rect->width || !rect->height)
return;
if (!par->accel_flags) {
cfb_fillrect(info, rect);
return;
}
if (info->fix.visual == FB_VISUAL_TRUECOLOR ||
info->fix.visual == FB_VISUAL_DIRECTCOLOR)
color = ((u32 *)(info->pseudo_palette))[rect->color];
else
color = rect->color;
if (info->var.bits_per_pixel == 24) {
dx *= 3;
width *= 3;
rotation = rotation24bpp(dx, DST_X_LEFT_TO_RIGHT);
}
wait_for_fifo(3, par);
aty_st_le32(DP_FRGD_CLR, color, par);
aty_st_le32(DP_SRC,
BKGD_SRC_BKGD_CLR | FRGD_SRC_FRGD_CLR | MONO_SRC_ONE,
par);
aty_st_le32(DST_CNTL,
DST_LAST_PEL | DST_Y_TOP_TO_BOTTOM |
DST_X_LEFT_TO_RIGHT | rotation, par);
draw_rect(dx, rect->dy, width, rect->height, par);
}
void aty_init_engine(struct atyfb_par *par, struct fb_info *info)
{
u32 pitch_value;
u32 vxres;
/* determine modal information from global mode structure */
pitch_value = info->fix.line_length / (info->var.bits_per_pixel / 8);
vxres = info->var.xres_virtual;
if (info->var.bits_per_pixel == 24) {
/* In 24 bpp, the engine is in 8 bpp - this requires that all */
/* horizontal coordinates and widths must be adjusted */
pitch_value *= 3;
vxres *= 3;
}
/* On GTC (RagePro), we need to reset the 3D engine before */
if (M64_HAS(RESET_3D))
reset_GTC_3D_engine(par);
/* Reset engine, enable, and clear any engine errors */
aty_reset_engine(par);
/* Ensure that vga page pointers are set to zero - the upper */
/* page pointers are set to 1 to handle overflows in the */
/* lower page */
aty_st_le32(MEM_VGA_WP_SEL, 0x00010000, par);
aty_st_le32(MEM_VGA_RP_SEL, 0x00010000, par);
/* ---- Setup standard engine context ---- */
/* All GUI registers here are FIFOed - therefore, wait for */
/* the appropriate number of empty FIFO entries */
wait_for_fifo(14, par);
/* enable all registers to be loaded for context loads */
aty_st_le32(CONTEXT_MASK, 0xFFFFFFFF, par);
/* set destination pitch to modal pitch, set offset to zero */
aty_st_le32(DST_OFF_PITCH, (pitch_value / 8) << 22, par);
/* zero these registers (set them to a known state) */
aty_st_le32(DST_Y_X, 0, par);
aty_st_le32(DST_HEIGHT, 0, par);
aty_st_le32(DST_BRES_ERR, 0, par);
aty_st_le32(DST_BRES_INC, 0, par);
aty_st_le32(DST_BRES_DEC, 0, par);
/* set destination drawing attributes */
aty_st_le32(DST_CNTL, DST_LAST_PEL | DST_Y_TOP_TO_BOTTOM |
DST_X_LEFT_TO_RIGHT, par);
/* set source pitch to modal pitch, set offset to zero */
aty_st_le32(SRC_OFF_PITCH, (pitch_value / 8) << 22, par);
/* set these registers to a known state */
aty_st_le32(SRC_Y_X, 0, par);
aty_st_le32(SRC_HEIGHT1_WIDTH1, 1, par);
aty_st_le32(SRC_Y_X_START, 0, par);
aty_st_le32(SRC_HEIGHT2_WIDTH2, 1, par);
/* set source pixel retrieving attributes */
aty_st_le32(SRC_CNTL, SRC_LINE_X_LEFT_TO_RIGHT, par);
/* set host attributes */
wait_for_fifo(13, par);
aty_st_le32(HOST_CNTL, 0, par);
/* set pattern attributes */
aty_st_le32(PAT_REG0, 0, par);
aty_st_le32(PAT_REG1, 0, par);
aty_st_le32(PAT_CNTL, 0, par);
/* set scissors to modal size */
aty_st_le32(SC_LEFT, 0, par);
aty_st_le32(SC_TOP, 0, par);
aty_st_le32(SC_BOTTOM, par->crtc.vyres - 1, par);
aty_st_le32(SC_RIGHT, vxres - 1, par);
/* set background color to minimum value (usually BLACK) */
aty_st_le32(DP_BKGD_CLR, 0, par);
/* set foreground color to maximum value (usually WHITE) */
aty_st_le32(DP_FRGD_CLR, 0xFFFFFFFF, par);
/* set write mask to effect all pixel bits */
aty_st_le32(DP_WRITE_MASK, 0xFFFFFFFF, par);
/* set foreground mix to overpaint and background mix to */
/* no-effect */
aty_st_le32(DP_MIX, FRGD_MIX_S | BKGD_MIX_D, par);
/* set primary source pixel channel to foreground color */
/* register */
aty_st_le32(DP_SRC, FRGD_SRC_FRGD_CLR, par);
/* set compare functionality to false (no-effect on */
/* destination) */
wait_for_fifo(3, par);
aty_st_le32(CLR_CMP_CLR, 0, par);
aty_st_le32(CLR_CMP_MASK, 0xFFFFFFFF, par);
aty_st_le32(CLR_CMP_CNTL, 0, par);
/* set pixel depth */
wait_for_fifo(2, par);
aty_st_le32(DP_PIX_WIDTH, par->crtc.dp_pix_width, par);
aty_st_le32(DP_CHAIN_MASK, par->crtc.dp_chain_mask, par);
wait_for_fifo(5, par);
aty_st_le32(SCALE_3D_CNTL, 0, par);
aty_st_le32(Z_CNTL, 0, par);
aty_st_le32(CRTC_INT_CNTL, aty_ld_le32(CRTC_INT_CNTL, par) & ~0x20,
par);
aty_st_le32(GUI_TRAJ_CNTL, 0x100023, par);
/* insure engine is idle before leaving */
wait_for_idle(par);
}
int atyfb_xl_init(struct fb_info *info)
{
const struct xl_card_cfg_t * card = &card_cfg[xl_card];
struct atyfb_par *par = (struct atyfb_par *) info->par;
union aty_pll pll;
int i, err;
u32 temp;
aty_st_8(CONFIG_STAT0, 0x85, par);
mdelay(10);
/*
* The following needs to be set before the call
* to var_to_pll() below. They'll be re-set again
* to the same values in aty_init().
*/
par->ref_clk_per = 100000000UL/card->ref_crystal;
par->ram_type = card->mem_type;
info->fix.smem_len = card->mem_size;
if (xl_card == VICTORIA) {
// the MCLK, XCLK are 120MHz on victoria card
par->mclk_per = 1000000/120;
par->xclk_per = 1000000/120;
par->features &= ~M64F_MFB_TIMES_4;
}
/*
* Calculate mclk and xclk dividers, etc. The passed
* pixclock and bpp values don't matter yet, the vclk
* isn't programmed until later.
*/
if ((err = aty_pll_ct.var_to_pll(info, 39726, 8, &pll)))
return err;
aty_st_pll(LVDS_CNTL0, 0x00, par);
aty_st_pll(DLL2_CNTL, card->dll2_cntl, par);
aty_st_pll(V2PLL_CNTL, 0x10, par);
aty_st_pll(MPLL_CNTL, MPLL_GAIN, par);
aty_st_pll(VPLL_CNTL, VPLL_GAIN, par);
aty_st_pll(PLL_VCLK_CNTL, 0x00, par);
aty_st_pll(VFC_CNTL, 0x1B, par);
aty_st_pll(PLL_REF_DIV, pll.ct.pll_ref_div, par);
aty_st_pll(PLL_EXT_CNTL, pll.ct.pll_ext_cntl, par);
aty_st_pll(SPLL_CNTL2, 0x03, par);
aty_st_pll(PLL_GEN_CNTL, 0x44, par);
reset_clocks(par, &pll.ct, 0);
mdelay(10);
aty_st_pll(VCLK_POST_DIV, 0x03, par);
aty_st_pll(VCLK0_FB_DIV, 0xDA, par);
aty_st_pll(VCLK_POST_DIV, 0x0F, par);
aty_st_pll(VCLK1_FB_DIV, 0xF5, par);
aty_st_pll(VCLK_POST_DIV, 0x3F, par);
aty_st_pll(PLL_EXT_CNTL, 0x40 | pll.ct.pll_ext_cntl, par);
aty_st_pll(VCLK2_FB_DIV, 0x00, par);
aty_st_pll(VCLK_POST_DIV, 0xFF, par);
aty_st_pll(PLL_EXT_CNTL, 0xC0 | pll.ct.pll_ext_cntl, par);
aty_st_pll(VCLK3_FB_DIV, 0x00, par);
aty_st_8(BUS_CNTL, 0x01, par);
aty_st_le32(BUS_CNTL, card->bus_cntl | 0x08000000, par);
aty_st_le32(CRTC_GEN_CNTL, 0x04000200, par);
aty_st_le16(CONFIG_STAT0, 0x0020, par);
aty_st_le32(MEM_CNTL, 0x10151A33, par);
aty_st_le32(EXT_MEM_CNTL, 0xE0000C01, par);
aty_st_le16(CRTC_GEN_CNTL+2, 0x0000, par);
aty_st_le32(DAC_CNTL, card->dac_cntl, par);
aty_st_le16(GEN_TEST_CNTL, 0x0100, par);
aty_st_le32(CUSTOM_MACRO_CNTL, 0x003C0171, par);
aty_st_le32(MEM_BUF_CNTL, 0x00382848, par);
aty_st_le32(HW_DEBUG, card->hw_debug, par);
aty_st_le16(MEM_ADDR_CONFIG, 0x0000, par);
aty_st_le16(GP_IO+2, 0x0000, par);
aty_st_le16(GEN_TEST_CNTL, 0x0000, par);
aty_st_le16(EXT_DAC_REGS+2, 0x0000, par);
aty_st_le32(CRTC_INT_CNTL, 0x00000000, par);
aty_st_le32(TIMER_CONFIG, 0x00000000, par);
aty_st_le32(0xEC, 0x00000000, par);
aty_st_le32(0xFC, 0x00000000, par);
for (i=0; i<sizeof(lcd_tbl)/sizeof(lcd_tbl_t); i++) {
aty_st_lcd(lcd_tbl[i].lcd_reg, lcd_tbl[i].val, par);
}
aty_st_le16(CONFIG_STAT0, 0x00A4, par);
mdelay(10);
aty_st_8(BUS_CNTL+1, 0xA0, par);
mdelay(10);
reset_clocks(par, &pll.ct, 1);
mdelay(10);
// something about power management
aty_st_8(LCD_INDEX, 0x08, par);
aty_st_8(LCD_DATA, 0x0A, par);
aty_st_8(LCD_INDEX, 0x08, par);
aty_st_8(LCD_DATA+3, 0x02, par);
aty_st_8(LCD_INDEX, 0x08, par);
aty_st_8(LCD_DATA, 0x0B, par);
mdelay(2);
// enable display requests, enable CRTC
aty_st_8(CRTC_GEN_CNTL+3, 0x02, par);
// disable display
aty_st_8(CRTC_GEN_CNTL, 0x40, par);
// disable display requests, disable CRTC
aty_st_8(CRTC_GEN_CNTL+3, 0x04, par);
mdelay(10);
aty_st_pll(PLL_YCLK_CNTL, 0x25, par);
aty_st_le16(CUSTOM_MACRO_CNTL, 0x0179, par);
aty_st_le16(CUSTOM_MACRO_CNTL+2, 0x005E, par);
aty_st_le16(CUSTOM_MACRO_CNTL+2, card->custom_macro_cntl>>16, par);
aty_st_8(CUSTOM_MACRO_CNTL+1,
(card->custom_macro_cntl>>8) & 0xff, par);
aty_st_le32(MEM_ADDR_CONFIG, card->mem_addr_config, par);
aty_st_le32(MEM_CNTL, card->mem_cntl, par);
aty_st_le32(EXT_MEM_CNTL, card->ext_mem_cntl, par);
aty_st_8(CONFIG_STAT0, 0xA0 | card->mem_type, par);
aty_st_pll(PLL_YCLK_CNTL, 0x01, par);
mdelay(15);
aty_st_pll(PLL_YCLK_CNTL, card->pll_yclk_cntl, par);
mdelay(1);
reset_clocks(par, &pll.ct, 0);
mdelay(50);
reset_clocks(par, &pll.ct, 0);
mdelay(50);
// enable extended register block
aty_st_8(BUS_CNTL+3, 0x7B, par);
mdelay(1);
// disable extended register block
aty_st_8(BUS_CNTL+3, 0x73, par);
aty_st_8(CONFIG_STAT0, 0x80 | card->mem_type, par);
// disable display requests, disable CRTC
aty_st_8(CRTC_GEN_CNTL+3, 0x04, par);
// disable mapping registers in VGA aperture
aty_st_8(CONFIG_CNTL, aty_ld_8(CONFIG_CNTL, par) & ~0x04, par);
mdelay(50);
// enable display requests, enable CRTC
aty_st_8(CRTC_GEN_CNTL+3, 0x02, par);
// make GPIO's 14,15,16 all inputs
aty_st_8(LCD_INDEX, 0x07, par);
aty_st_8(LCD_DATA+3, 0x00, par);
// enable the display
aty_st_8(CRTC_GEN_CNTL, 0x00, par);
mdelay(17);
// reset the memory controller
aty_st_8(GEN_TEST_CNTL+1, 0x02, par);
mdelay(15);
aty_st_8(GEN_TEST_CNTL+1, 0x00, par);
mdelay(30);
// enable extended register block
aty_st_8(BUS_CNTL+3,
(u8)(aty_ld_8(BUS_CNTL+3, par) | 0x08),
par);
// set FIFO size to 512 (PIO)
aty_st_le32(GUI_CNTL,
aty_ld_le32(GUI_CNTL, par) & ~0x3,
par);
// enable CRT and disable lcd
aty_st_8(LCD_INDEX, 0x01, par);
temp = aty_ld_le32(LCD_DATA, par);
temp = (temp | 0x01) & ~0x02;
aty_st_le32(LCD_DATA, temp, par);
return 0;
}
void atyfb_imageblit(struct fb_info *info, const struct fb_image *image)
{
struct atyfb_par *par = (struct atyfb_par *) info->par;
u32 src_bytes, dx = image->dx, dy = image->dy, width = image->width;
u32 pix_width_save, pix_width, host_cntl, rotation = 0, src, mix;
if (par->asleep)
return;
if (!image->width || !image->height)
return;
if (!par->accel_flags ||
(image->depth != 1 && info->var.bits_per_pixel != image->depth)) {
cfb_imageblit(info, image);
return;
}
pix_width = pix_width_save = aty_ld_le32(DP_PIX_WIDTH, par);
host_cntl = aty_ld_le32(HOST_CNTL, par) | HOST_BYTE_ALIGN;
switch (image->depth) {
case 1:
pix_width &= ~(BYTE_ORDER_MASK | HOST_MASK);
pix_width |= (BYTE_ORDER_MSB_TO_LSB | HOST_1BPP);
break;
case 4:
pix_width &= ~(BYTE_ORDER_MASK | HOST_MASK);
pix_width |= (BYTE_ORDER_MSB_TO_LSB | HOST_4BPP);
break;
case 8:
pix_width &= ~HOST_MASK;
pix_width |= HOST_8BPP;
break;
case 15:
pix_width &= ~HOST_MASK;
pix_width |= HOST_15BPP;
break;
case 16:
pix_width &= ~HOST_MASK;
pix_width |= HOST_16BPP;
break;
case 24:
pix_width &= ~HOST_MASK;
pix_width |= HOST_24BPP;
break;
case 32:
pix_width &= ~HOST_MASK;
pix_width |= HOST_32BPP;
break;
}
if (info->var.bits_per_pixel == 24) {
/* In 24 bpp, the engine is in 8 bpp - this requires that all */
/* horizontal coordinates and widths must be adjusted */
dx *= 3;
width *= 3;
rotation = rotation24bpp(dx, DST_X_LEFT_TO_RIGHT);
pix_width &= ~DST_MASK;
pix_width |= DST_8BPP;
/*
* since Rage 3D IIc we have DP_HOST_TRIPLE_EN bit
* this hwaccelerated triple has an issue with not aligned data
*/
if (M64_HAS(HW_TRIPLE) && image->width % 8 == 0)
pix_width |= DP_HOST_TRIPLE_EN;
}
if (image->depth == 1) {
u32 fg, bg;
if (info->fix.visual == FB_VISUAL_TRUECOLOR ||
info->fix.visual == FB_VISUAL_DIRECTCOLOR) {
fg = ((u32*)(info->pseudo_palette))[image->fg_color];
bg = ((u32*)(info->pseudo_palette))[image->bg_color];
} else {
fg = image->fg_color;
bg = image->bg_color;
}
wait_for_fifo(2, par);
aty_st_le32(DP_BKGD_CLR, bg, par);
aty_st_le32(DP_FRGD_CLR, fg, par);
src = MONO_SRC_HOST | FRGD_SRC_FRGD_CLR | BKGD_SRC_BKGD_CLR;
mix = FRGD_MIX_S | BKGD_MIX_S;
} else {
src = MONO_SRC_ONE | FRGD_SRC_HOST;
mix = FRGD_MIX_D_XOR_S | BKGD_MIX_D;
}
wait_for_fifo(6, par);
aty_st_le32(DP_WRITE_MASK, 0xFFFFFFFF, par);
aty_st_le32(DP_PIX_WIDTH, pix_width, par);
aty_st_le32(DP_MIX, mix, par);
aty_st_le32(DP_SRC, src, par);
aty_st_le32(HOST_CNTL, host_cntl, par);
aty_st_le32(DST_CNTL, DST_Y_TOP_TO_BOTTOM | DST_X_LEFT_TO_RIGHT | rotation, par);
draw_rect(dx, dy, width, image->height, par);
src_bytes = (((image->width * image->depth) + 7) / 8) * image->height;
/* manual triple each pixel */
if (info->var.bits_per_pixel == 24 && !(pix_width & DP_HOST_TRIPLE_EN)) {
int inbit, outbit, mult24, byte_id_in_dword, width;
u8 *pbitmapin = (u8*)image->data, *pbitmapout;
u32 hostdword;
for (width = image->width, inbit = 7, mult24 = 0; src_bytes; ) {
for (hostdword = 0, pbitmapout = (u8*)&hostdword, byte_id_in_dword = 0;
byte_id_in_dword < 4 && src_bytes;
byte_id_in_dword++, pbitmapout++) {
for (outbit = 7; outbit >= 0; outbit--) {
*pbitmapout |= (((*pbitmapin >> inbit) & 1) << outbit);
mult24++;
/* next bit */
if (mult24 == 3) {
mult24 = 0;
inbit--;
width--;
}
/* next byte */
if (inbit < 0 || width == 0) {
src_bytes--;
pbitmapin++;
inbit = 7;
if (width == 0) {
width = image->width;
outbit = 0;
}
}
}
}
wait_for_fifo(1, par);
aty_st_le32(HOST_DATA0, hostdword, par);
}
} else {
static int aty_set_dac_ATI68860_B(const struct fb_info *info,
const union aty_pll *pll, u32 bpp,
u32 accel)
{
struct atyfb_par *par = (struct atyfb_par *) info->par;
u32 gModeReg, devSetupRegA, temp, mask;
gModeReg = 0;
devSetupRegA = 0;
switch (bpp) {
case 8:
gModeReg = 0x83;
devSetupRegA =
0x60 | 0x00 /*(info->mach64DAC8Bit ? 0x00 : 0x01) */ ;
break;
case 15:
gModeReg = 0xA0;
devSetupRegA = 0x60;
break;
case 16:
gModeReg = 0xA1;
devSetupRegA = 0x60;
break;
case 24:
gModeReg = 0xC0;
devSetupRegA = 0x60;
break;
case 32:
gModeReg = 0xE3;
devSetupRegA = 0x60;
break;
}
if (!accel) {
gModeReg = 0x80;
devSetupRegA = 0x61;
}
temp = aty_ld_8(DAC_CNTL, par);
aty_st_8(DAC_CNTL, (temp & ~DAC_EXT_SEL_RS2) | DAC_EXT_SEL_RS3,
par);
aty_st_8(DAC_REGS + 2, 0x1D, par);
aty_st_8(DAC_REGS + 3, gModeReg, par);
aty_st_8(DAC_REGS, 0x02, par);
temp = aty_ld_8(DAC_CNTL, par);
aty_st_8(DAC_CNTL, temp | DAC_EXT_SEL_RS2 | DAC_EXT_SEL_RS3, par);
if (info->fix.smem_len < ONE_MB)
mask = 0x04;
else if (info->fix.smem_len == ONE_MB)
mask = 0x08;
else
mask = 0x0C;
/* The following assumes that the BIOS has correctly set R7 of the
* Device Setup Register A at boot time.
*/
#define A860_DELAY_L 0x80
temp = aty_ld_8(DAC_REGS, par);
aty_st_8(DAC_REGS, (devSetupRegA | mask) | (temp & A860_DELAY_L),
par);
temp = aty_ld_8(DAC_CNTL, par);
aty_st_8(DAC_CNTL, (temp & ~(DAC_EXT_SEL_RS2 | DAC_EXT_SEL_RS3)),
par);
aty_st_le32(BUS_CNTL, 0x890e20f1, par);
aty_st_le32(DAC_CNTL, 0x47052100, par);
return 0;
}
static inline void aty_st_lcd(u8 lcd_reg, u32 val,
struct atyfb_par *par)
{
aty_st_8(LCD_INDEX, lcd_reg, par);
aty_st_le32(LCD_DATA, val, par);
}
void aty_init_engine(struct atyfb_par *par, struct fb_info *info)
{
u32 pitch_value;
u32 vxres;
pitch_value = info->fix.line_length / (info->var.bits_per_pixel / 8);
vxres = info->var.xres_virtual;
if (info->var.bits_per_pixel == 24) {
pitch_value *= 3;
vxres *= 3;
}
if (M64_HAS(RESET_3D))
reset_GTC_3D_engine(par);
aty_reset_engine(par);
aty_st_le32(MEM_VGA_WP_SEL, 0x00010000, par);
aty_st_le32(MEM_VGA_RP_SEL, 0x00010000, par);
wait_for_fifo(14, par);
aty_st_le32(CONTEXT_MASK, 0xFFFFFFFF, par);
aty_st_le32(DST_OFF_PITCH, (pitch_value / 8) << 22, par);
aty_st_le32(DST_Y_X, 0, par);
aty_st_le32(DST_HEIGHT, 0, par);
aty_st_le32(DST_BRES_ERR, 0, par);
aty_st_le32(DST_BRES_INC, 0, par);
aty_st_le32(DST_BRES_DEC, 0, par);
aty_st_le32(DST_CNTL, DST_LAST_PEL | DST_Y_TOP_TO_BOTTOM |
DST_X_LEFT_TO_RIGHT, par);
aty_st_le32(SRC_OFF_PITCH, (pitch_value / 8) << 22, par);
aty_st_le32(SRC_Y_X, 0, par);
aty_st_le32(SRC_HEIGHT1_WIDTH1, 1, par);
aty_st_le32(SRC_Y_X_START, 0, par);
aty_st_le32(SRC_HEIGHT2_WIDTH2, 1, par);
aty_st_le32(SRC_CNTL, SRC_LINE_X_LEFT_TO_RIGHT, par);
wait_for_fifo(13, par);
aty_st_le32(HOST_CNTL, 0, par);
aty_st_le32(PAT_REG0, 0, par);
aty_st_le32(PAT_REG1, 0, par);
aty_st_le32(PAT_CNTL, 0, par);
aty_st_le32(SC_LEFT, 0, par);
aty_st_le32(SC_TOP, 0, par);
aty_st_le32(SC_BOTTOM, par->crtc.vyres - 1, par);
aty_st_le32(SC_RIGHT, vxres - 1, par);
aty_st_le32(DP_BKGD_CLR, 0, par);
aty_st_le32(DP_FRGD_CLR, 0xFFFFFFFF, par);
aty_st_le32(DP_WRITE_MASK, 0xFFFFFFFF, par);
aty_st_le32(DP_MIX, FRGD_MIX_S | BKGD_MIX_D, par);
aty_st_le32(DP_SRC, FRGD_SRC_FRGD_CLR, par);
wait_for_fifo(3, par);
aty_st_le32(CLR_CMP_CLR, 0, par);
aty_st_le32(CLR_CMP_MASK, 0xFFFFFFFF, par);
aty_st_le32(CLR_CMP_CNTL, 0, par);
wait_for_fifo(2, par);
aty_st_le32(DP_PIX_WIDTH, par->crtc.dp_pix_width, par);
aty_st_le32(DP_CHAIN_MASK, par->crtc.dp_chain_mask, par);
wait_for_fifo(5, par);
aty_st_le32(SCALE_3D_CNTL, 0, par);
aty_st_le32(Z_CNTL, 0, par);
aty_st_le32(CRTC_INT_CNTL, aty_ld_le32(CRTC_INT_CNTL, par) & ~0x20,
par);
aty_st_le32(GUI_TRAJ_CNTL, 0x100023, par);
wait_for_idle(par);
}
