pulsesequence()
{
char lkflg[MAXSTR];
getstr("lkflg",lkflg);
status(A);
dec3blank();
if (lkflg[A]=='y') lk_sample();
hsdelay(d1);
status(B);
pulse(p1, zero);
hsdelay(d2);
status(C);
pulse(pw,oph);
if (lkflg[A]=='y') lk_hold();
dec3unblank();
}
pulsesequence()
{
/* DECLARE AND LOAD VARIABLES; parameters used in the last half of the */
/* sequence are declared and initialized as 0.0 in bionmr.h, and */
/* reinitialized below */
char f1180[MAXSTR], /* Flag to start t1 @ halfdwell */
f2180[MAXSTR], /* Flag to start t2 @ halfdwell */
TROSY[MAXSTR]; /* do TROSY on N15 and H1 */
int t1_counter, /* used for states tppi in t1 */
t2_counter, /* used for states tppi in t2 */
ni = getval("ni"),
ni2 = getval("ni2");
double d2_init=0.0, /* used for states tppi in t1 */
d3_init=0.0, /* used for states tppi in t2 */
tau1, /* t1 delay */
BPdpwrspinlock, /* user-defined upper limit for spinlock(Hz) */
BPpwrlimits, /* =0 for no limit, =1 for limit */
t1a, /* time increments for first dimension */
t1b,
t1c,
tauCH = getval("tauCH"), /* 1/4J delay for CH */
timeTN = getval("timeTN"), /* constant time for 15N evolution */
epsilon = 1.05e-3, /* other delays */
zeta = 3.0e-3,
eta = 4.6e-3,
theta = 14.0e-3,
sheila, /* to transfer J evolution time hyperbolically into tau1 */
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
widthHd,
pwS1, /* length of square 90 on Cab */
pwS2, /* length of square 180 on Ca */
phi7cal = getval("phi7cal"), /* phase in degrees of the last C13 90 pulse */
spinlock = getval("spinlock"), /* DIPSI-3 spinlock field */
ncyc = getval("ncyc"), /* no. of cycles of DIPSI-3 decoupling on Cab */
pwNlvl = getval("pwNlvl"), /* power for N15 pulses */
pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */
sw1 = getval("sw1"),
sw2 = getval("sw2"),
waltzB1 = getval("waltzB1"),
gt0 = getval("gt0"), /* other gradients */
gt3 = getval("gt3"),
gt4 = getval("gt4"),
gzlvl0 = getval("gzlvl0"),
gzlvl3 = getval("gzlvl3"),
gzlvl4 = getval("gzlvl4");
getstr("f1180",f1180);
getstr("f2180",f2180);
getstr("TROSY",TROSY);
widthHd=2.069*(waltzB1/sfrq); /* produces same field as std. sequence */
/* LOAD PHASE TABLE */
settable(t3,1,phx);
settable(t4,1,phx);
settable(t5,2,phi5);
settable(t6,2,phi6);
if (TROSY[A]=='y')
{settable(t8,1,phy);
settable(t9,1,phx);
settable(t10,1,phy);
settable(t11,1,phx);
settable(t12,2,recT);}
else
{settable(t8,1,phx);
settable(t9,8,phi9);
settable(t10,1,phx);
settable(t11,1,phy);
settable(t12,4,rec);}
/* INITIALIZE VARIABLES */
P_getreal(GLOBAL,"BPpwrlimits",&BPpwrlimits,1);
P_getreal(GLOBAL,"BPdpwrspinlock",&BPdpwrspinlock,1);
if (BPpwrlimits > 0.5)
{
if (spinlock > BPdpwrspinlock)
{
printf("spinlock too large, reset to user-defined limit (BPdpwrspinlock)");
psg_abort(1);
}
}
kappa = 5.4e-3;
lambda = 2.4e-3;
if( pwC > 24.0*600.0/sfrq )
{ printf("increase pwClvl so that pwC < 24*600/sfrq");
psg_abort(1); }
/* get calculated pulse lengths of shaped C13 pulses */
pwS1 = c13pulsepw("cab", "co", "square", 90.0);
pwS2 = c13pulsepw("ca", "co", "square", 180.0);
/* CHECK VALIDITY OF PARAMETER RANGES */
if ( gt4 > epsilon - 0.6*pwC)
{ printf(" gt4 is too big. Make gt4 equal to %f or less.\n",
(epsilon - 0.6*pwC)); psg_abort(1);}
if ( 0.5*ni2*1/(sw2) > timeTN - WFG3_START_DELAY)
{ printf(" ni2 is too big. Make ni2 equal to %d or less.\n",
((int)((timeTN - WFG3_START_DELAY)*2.0*sw2))); psg_abort(1);}
if ( dm[A] == 'y' || dm[B] == 'y' || dm[C] == 'y' )
{ printf("incorrect dec1 decoupler flags! Should be 'nnn' "); psg_abort(1);}
if ( dm2[A] == 'y' || dm2[B] == 'y' )
{ printf("incorrect dec2 decoupler flags! Should be 'nny' "); psg_abort(1);}
if ( dm3[A] == 'y' || dm3[C] == 'y' )
{ printf("incorrect dec3 decoupler flags! Should be 'nyn' or 'nnn' ");
psg_abort(1);}
if ( dpwr2 > 50 )
{ printf("dpwr2 too large! recheck value "); psg_abort(1);}
if ( pw > 20.0e-6 )
{ printf(" pw too long ! recheck value "); psg_abort(1);}
if ( pwN > 100.0e-6 )
{ printf(" pwN too long! recheck value "); psg_abort(1);}
if ( TROSY[A]=='y' && dm2[C] == 'y' )
{ text_error("Choose either TROSY='n' or dm2='n' ! "); psg_abort(1);}
/* PHASES AND INCREMENTED TIMES */
/* Phase incrementation for hypercomplex 2D data, States-Haberkorn element */
if (phase1 == 2) tsadd(t3,1,4);
if (TROSY[A]=='y')
{ if (phase2 == 2) icosel = +1;
else {tsadd(t4,2,4); tsadd(t10,2,4); icosel = -1;}
}
else { if (phase2 == 2) {tsadd(t10,2,4); icosel = +1;}
else icosel = -1;
}
/* C13 TIME INCREMENTATION and set up f1180 */
/* Set up f1180 */
tau1 = d2;
if((f1180[A] == 'y') && (ni > 1.0))
{ tau1 += ( 1.0 / (2.0*sw1) ); if(tau1 < 0.2e-6) tau1 = 0.0; }
tau1 = tau1/2.0;
/* Hyperbolic sheila seems superior to original zeta approach */
/* subtract unavoidable delays from tauCH */
tauCH = tauCH - gt0 - 2.0*GRADIENT_DELAY - 5.0e-5;
if ((ni-1)/(2.0*sw1) > 2.0*tauCH)
{
if (tau1 > 2.0*tauCH) sheila = tauCH;
else if (tau1 > 0) sheila = 1.0/(1.0/tau1+1.0/tauCH-1.0/(2.0*tauCH));
else sheila = 0.0;
}
else
{
if (tau1 > 0) sheila = 1.0/(1.0/tau1 + 1.0/tauCH - 2.0*sw1/((double)(ni-1)));
else sheila = 0.0;
}
t1a = tau1 + tauCH;
t1b = tau1 - sheila;
t1c = tauCH - sheila;
/* Set up f2180 */
tau2 = d3;
if((f2180[A] == 'y') && (ni2 > 1.0))
{ tau2 += ( 1.0 / (2.0*sw2) ); if(tau2 < 0.2e-6) tau2 = 0.0; }
tau2 = tau2/2.0;
/* Calculate modifications to phases for States-TPPI acquisition */
if( ix == 1) d2_init = d2;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if(t1_counter % 2)
{ tsadd(t3,2,4); tsadd(t12,2,4); }
if( ix == 1) d3_init = d3;
t2_counter = (int) ( (d3-d3_init)*sw2 + 0.5 );
if(t2_counter % 2)
{ tsadd(t8,2,4); tsadd(t12,2,4); }
/* BEGIN PULSE SEQUENCE */
status(A);
delay(d1);
if ( dm3[B] == 'y' )
{ lk_hold(); lk_sampling_off();} /*freezes z0 correction, stops lock pulsing*/
rcvroff();
set_c13offset("cab");
obsoffset(tof);
obspower(tpwr);
obspwrf(4095.0);
decpower(pwClvl);
decpwrf(4095.0);
dec2power(pwNlvl);
txphase(three);
delay(1.0e-5);
if (TROSY[A] == 'n')
dec2rgpulse(pwN, zero, 0.0, 0.0); /*destroy N15 and C13 magnetization*/
decrgpulse(pwC, zero, 0.0, 0.0);
zgradpulse(gzlvl0, 0.5e-3);
delay(1.0e-4);
if (TROSY[A] == 'n')
dec2rgpulse(pwN, one, 0.0, 0.0);
decrgpulse(pwC, zero, 0.0, 0.0);
zgradpulse(0.7*gzlvl0, 0.5e-3);
delay(5.0e-4);
if ( dm3[B] == 'y' ) /* begins optional 2H decoupling */
{
gzlvl0=0.0; gzlvl3=0.0; gzlvl4=0.0; /* no gradients during 2H decoupling */
dec3rgpulse(1/dmf3,one,10.0e-6,2.0e-6);
dec3unblank();
dec3phase(zero);
delay(2.0e-6);
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
}
rgpulse(pw, three, 0.0, 0.0); /* 1H pulse excitation */
/* point a */
txphase(zero);
decphase(zero);
zgradpulse(gzlvl0, gt0); /* 2.0*GRADIENT_DELAY */
delay(5.0e-5);
delay(t1a - 2.0*pwC);
decrgpulse(2.0*pwC, zero, 0.0, 0.0);
delay(t1b);
rgpulse(2.0*pw, zero, 0.0, 0.0);
zgradpulse(gzlvl0, gt0); /* 2.0*GRADIENT_DELAY */
txphase(t3);
delay(5.0e-5);
delay(t1c);
/* point b */
rgpulse(pw, t3, 0.0, 0.0);
zgradpulse(gzlvl3, gt3);
delay(2.0e-4);
decrgpulse(pwC, zero, 0.0, 0.0);
/* point c */
zgradpulse(gzlvl4, gt4);
delay(epsilon - gt4 - 0.6*pwC);
/* WFG2_START_DELAY */
sim_c13pulse("", "cab", "co", "square", 2.0*pw, 180.0,
zero, zero, 2.0e-6, 2.0e-6);
delay(WFG2_START_DELAY);
zgradpulse(gzlvl4, gt4);
delay(epsilon - gt4);
/* point d */
decrgpulse(0.5e-3, zero, 0.0, 0.0);
c13decouple("cab", "DIPSI3", 2.0*spinlock/dfrq, ncyc); /* PRG_STOP_DELAY */
/* point e */
h1decon("DIPSI2", widthHd, 0.0);/*POWER_DELAY+PWRF_DELAY+PRG_START_DELAY */
decphase(t5);
delay(zeta - PRG_STOP_DELAY - PRG_START_DELAY - POWER_DELAY -
PWRF_DELAY - 0.5*10.933*pwC);
decrgpulse(pwC*158.0/90.0, t5, 0.0, 0.0);
decrgpulse(pwC*171.2/90.0, t6, 0.0, 0.0);
decrgpulse(pwC*342.8/90.0, t5, 0.0, 0.0); /* Shaka composite */
decrgpulse(pwC*145.5/90.0, t6, 0.0, 0.0);
decrgpulse(pwC*81.2/90.0, t5, 0.0, 0.0);
decrgpulse(pwC*85.3/90.0, t6, 0.0, 0.0);
decphase(zero);
delay(zeta - 0.5*10.933*pwC - 0.6*pwS1 - WFG_START_DELAY - 2.0e-6);
/* WFG_START_DELAY */
c13pulse("cab", "co", "square", 90.0, zero, 2.0e-6, 0.0); /* point f */
decphase(t5);
if ( dm3[B] == 'y' ) /* turns off 2H decoupling */
{
gzlvl0=getval("gzlvl0");
gzlvl3=getval("gzlvl3");
gzlvl4=getval("gzlvl4");
setstatus(DEC3ch, FALSE, 'c', FALSE, dmf3);
dec3rgpulse(1/dmf3,three,2.0e-6,2.0e-6);
dec3blank();
lk_autotrig(); /* resumes lock pulsing */
}
zgradpulse(gzlvl3, gt3);
delay(2.0e-4);
c13pulse("co", "ca", "sinc", 90.0, t5, 2.0e-6, 0.0);
/* point g */
decphase(zero);
delay(eta - 2.0*POWER_DELAY - 2.0*PWRF_DELAY);
/* 2*POWER_DELAY+2*PWRF_DELAY */
c13pulse("ca", "co", "square", 180.0, zero, 2.0e-6, 0.0); /* pwS2 */
dec2phase(zero);
delay(theta - eta - pwS2 - WFG3_START_DELAY);
/* WFG3_START_DELAY */
sim3_c13pulse("", "co", "ca", "sinc", "", 0.0, 180.0, 2.0*pwN,
zero, zero, zero, 2.0e-6, 2.0e-6);
initval(phi7cal, v7);
decstepsize(1.0);
dcplrphase(v7); /* SAPS_DELAY */
dec2phase(t8);
delay(theta - SAPS_DELAY);
/* point h */
nh_evol_se_train("co", "ca"); /* common part of sequence in bionmr.h */
if (dm3[B]=='y') lk_sample();
}
void pulsesequence()
{
/* DECLARE AND LOAD VARIABLES; parameters used in the last half of the */
/* sequence are declared and initialized as 0.0 in bionmr.h, and */
/* reinitialized below */
char f2180[MAXSTR], /* Flag to start t2 @ halfdwell */
fil_flg1[MAXSTR],
had_flg[MAXSTR],
shname1[MAXSTR],
shname2[MAXSTR],
ala_flg[MAXSTR],
ser_flg[MAXSTR],
SE_flg[MAXSTR], /* SE_flg */
TROSY[MAXSTR]; /* do TROSY on N15 and H1 */
int t2_counter, /* used for states tppi in t2 */
ni2 = getval("ni2");
double d3_init=0.0, /* used for states tppi in t2 */
stCwidth = 80.0,
shpw1,shpw2, /* t1 delay */
tauCH = getval("tauCH"), /* 1/4J delay for CH */
tauC1 = getval("tauC1"),
tauC2 = getval("tauC2"),
tauC3 = getval("tauC3"),
had2,had3,
timeTN = getval("timeTN"), /* constant time for 15N evolution */
eta = 4.6e-3,
theta = 14.0e-3,
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
pwS1, pwS2, pwS3, pwS4, pwS5,pwS6,pwS7,
phi7cal = getval("phi7cal"), /* phase in degrees of the last C13 90 pulse */
pwNlvl = getval("pwNlvl"), /* power for N15 pulses */
pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */
sw2 = getval("sw2"),
gt3 = getval("gt3"),
gt5 = getval("gt5"),
gstab = getval("gstab"),
gzlvl0 = getval("gzlvl0"),
gzlvl3 = getval("gzlvl3"),
gzlvl5 = getval("gzlvl5"),
flip_angle=120.0,had1=0.0,
epsilon = getval("epsilon");
fil_flg1[0]='n';
ser_flg[0]='n'; /*initialize*/
getstr("f2180",f2180);
getstr("had_flg",had_flg);
getstr("shname1",shname1);
getstr("shname2",shname2);
getstr("TROSY",TROSY);
getstr("SE_flg",SE_flg);
/* LOAD PHASE TABLE */
settable(t1,4,phi1);
settable(t3,4,phi3);
settable(t4,1,phx);
settable(t5,2,phi5);
settable(t6,2,phi6);
settable(t8,1,phx);
settable(t9,8,phi9);
settable(t10,1,phx);
settable(t11,1,phy);
settable(t12,8,phi12);
settable(t13,8,rec2);
/* INITIALIZE VARIABLES */
shpw1 = pw*8.0;
shpw2 = pwC*8.0;
kappa = 5.4e-3;
lambda = 2.4e-3;
had2=0.5/135.0;
had3=0.5/135.0;
ala_flg[0]='n';
if (had_flg[0] == '1')
{ fil_flg1[0]='n';ser_flg[0]='n';flip_angle=120.0;had1=0.0;}
if (had_flg[0] == '2')
{ fil_flg1[0]='y';ser_flg[0]='n';flip_angle=120.0;had1=0.0;}
if (had_flg[0] == '3')
{ fil_flg1[0]='n';ser_flg[0]='y';flip_angle=120.0;had1=0.0;}
if (had_flg[0] == '4')
{ fil_flg1[0]='y';ser_flg[0]='y';flip_angle=120.0;had1=0.0;}
if (had_flg[0] == '5')
{ fil_flg1[0]='n';ser_flg[0]='n';flip_angle=60.0;had1=0.5/140.0;}
if (had_flg[0] == '6')
{ fil_flg1[0]='y';ser_flg[0]='n';flip_angle=60.0;had1=0.5/140.0;}
if (had_flg[0] == '7')
{ fil_flg1[0]='n';ser_flg[0]='y';flip_angle=60.0;had1=0.5/140.0;}
if (had_flg[0] == '8')
{ fil_flg1[0]='y';ser_flg[0]='y';flip_angle=60.0;had1=0.5/140.0;}
if( pwC > 20.0*600.0/sfrq )
{ printf("increase pwClvl so that pwC < 20*600/sfrq");
psg_abort(1); }
/* get calculated pulse lengths of shaped C13 pulses */
pwS1 = c13pulsepw("cab", "co", "square", 90.0);
pwS2 = c13pulsepw("ca", "co", "square", 180.0);
pwS3 = c13pulsepw("co", "ca", "sinc", 180.0);
pwS4 = c_shapedpw("isnob5",80.0,0.0,zero, 2.0e-6, 2.0e-6);
pwS6 = c_shapedpw("reburp",80.0,0.0,zero, 2.0e-6, 2.0e-6); /* attention, y a aussi des 180 CaCb après les filtres*/
pwS7 = c_shapedpw(shname2,80.0,150.0,zero, 2.0e-6, 2.0e-6);
pwS5 = c_shapedpw("isnob5",30.0,0.0,zero, 2.0e-6, 2.0e-6);
/* CHECK VALIDITY OF PARAMETER RANGES */
if ( 0.5*ni2*1/(sw2) > timeTN - WFG3_START_DELAY)
{ printf(" ni2 is too big. Make ni2 equal to %d or less.\n",
((int)((timeTN - WFG3_START_DELAY)*2.0*sw2))); psg_abort(1);}
if ( dm[A] == 'y' || dm[B] == 'y' || dm[C] == 'y' )
{ printf("incorrect dec1 decoupler flags! Should be 'nnn' "); psg_abort(1);}
if ( dm2[A] == 'y' || dm2[B] == 'y' )
{ printf("incorrect dec2 decoupler flags! Should be 'nny' "); psg_abort(1);}
if ( dm3[A] == 'y' || dm3[C] == 'y' )
{ printf("incorrect dec3 decoupler flags! Should be 'nyn' or 'nnn' ");
psg_abort(1);}
if ( dpwr2 > 46 )
{ printf("dpwr2 too large! recheck value "); psg_abort(1);}
if ( pw > 20.0e-6 )
{ printf(" pw too long ! recheck value "); psg_abort(1);}
if ( pwN > 100.0e-6 )
{ printf(" pwN too long! recheck value "); psg_abort(1);}
if ( TROSY[A]=='y' && dm2[C] == 'y' )
{ text_error("Choose either TROSY='n' or dm2='n' ! "); psg_abort(1);}
/* PHASES AND INCREMENTED TIMES */
/* Phase incrementation for hypercomplex 2D data, States-Haberkorn element */
if (TROSY[A]=='y')
{ if (phase2 == 2) icosel = +1;
else {tsadd(t4,2,4); tsadd(t10,2,4); icosel = -1;}
}
else {
if (SE_flg[0]=='y')
{
if (phase2 == 2) {tsadd(t10,2,4); icosel = +1;}
else icosel = -1;
}
else { if (phase2 == 2) {tsadd(t8,1,4); }
}
}
/* Set up f2180 */
tau2 = d3; /* run 2D exp for NH correlation, but must use tau2 instead of tau1
because bionmr.h is written for nh_evol* to do tau2 evolution*/
if((f2180[A] == 'y') && (ni2 > 1.0)) /* use f2180 to control tau2 */
{ tau2 += ( 1.0 / (2.0*sw2) ); if(tau2 < 0.2e-6) tau2 = 0.0; }
tau2 = tau2/2.0;
/* Calculate modifications to phases for States-TPPI acquisition */
if( ix == 1) d3_init = d3;
t2_counter = (int) ( (d3-d3_init)*sw1 + 0.5 );
if(t2_counter % 2)
{ tsadd(t8,2,4); tsadd(t12,2,4); tsadd(t13,2,4); }
/* BEGIN PULSE SEQUENCE */
status(A);
delay(d1);
if (dm3[B]=='y') lk_hold();
rcvroff();
set_c13offset("cab");
obsoffset(tof);
obspower(tpwr);
obspwrf(4095.0);
decpower(pwClvl);
decpwrf(4095.0);
dec2power(pwNlvl);
txphase(one);
delay(1.0e-5);
if (TROSY[A] == 'n')
dec2rgpulse(pwN, zero, 0.0, 0.0); /*destroy N15 and C13 magnetization*/
decrgpulse(pwC, zero, 0.0, 0.0);
zgradpulse(gzlvl0, 0.5e-3);
delay(gstab);
if (TROSY[A] == 'n')
dec2rgpulse(pwN, one, 0.0, 0.0);
decrgpulse(pwC, zero, 0.0, 0.0);
zgradpulse(0.7*gzlvl0, 0.5e-3);
delay(gstab);
if(dm3[B] == 'y') /*optional 2H decoupling on */
{dec3unblank(); dec3rgpulse(1/dmf3, one, 0.0, 0.0);
dec3unblank(); setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);}
rgpulse(pw, zero, 2.0e-6, 0.0);
zgradpulse(gzlvl5, gt5);
delay(tauCH - gt5 - WFG2_START_DELAY - 0.5e-3 + 68.0e-6 );
sim_c13adiab_inv_pulse("", "aliph", stCwidth, "sech1", 2.0*pw, 1.0e-3,
zero, zero, 2.0e-6, 2.0e-6);
zgradpulse(gzlvl5, gt5);
delay(tauCH - gt5 - 0.5e-3 + 68.0e-6);
rgpulse(pw, one, 0.0, 0.0);
if (ser_flg[0] == 'n' )
delay(pwS5);
if (ser_flg[0] == 'y' )
c_shapedpulse("isnob5",30.0,24.0,zero, 2.0e-6, 2.0e-6);
/*********************************** transfer CB->CA + DEPT CBH **************/
zgradpulse(gzlvl3, gt3*1.2);
delay(gstab);
decrgpulse(pwC, t3, 0.0, 0.0);
rgpulse(pw, three, 0.0, 0.0);
if (flip_angle > 90.0) delay(pw*(flip_angle/90.0-1));
if (fil_flg1[0] == 'y')
{
/* JCOCA & JCOCB is turned on*/
zgradpulse(gzlvl3, gt3);
delay(had2*0.5-pwS4*0.5-pwS7-gt3);
c_simshapedpulse(shname2,80.0,150.0,0.0,0.0,zero,zero,zero, 2.0e-6, 2.0e-6);
c_simshapedpulse("isnob5",80.0,0.0,pw*2.0,0.0,zero,zero,zero, 2.0e-6, 2.0e-6);
zgradpulse(gzlvl3, gt3);
delay(had2*0.5-pwS4*0.5-gt3);
rgpulse(pw*flip_angle/90.0, t1, 0.0, 0.0);
if (flip_angle < 90.0) delay(pw*(1-flip_angle/90.0));
zgradpulse(gzlvl3, 1.1*gt3);
delay(had3*0.5-shpw1*0.5-1.1*gt3);
shaped_pulse(shname1,shpw1,two,0.0,0.0);
delay((tauC3-(had2+pw*120/90*2))*0.5-pwS4*0.5-had3*0.5-shpw1*0.5-pwS7);
c_simshapedpulse(shname2,80.0,150.0,0.0,0.0,zero,zero,zero, 2.0e-6, 2.0e-6);
c_shapedpulse("isnob5",80.0,0.0,two, 2.0e-6, 2.0e-6);
zgradpulse(gzlvl3, 1.1*gt3);
delay((tauC3-(had2+pw*120/90*2))*0.5-pwS4*0.5-1.1*gt3);
}
if (fil_flg1[0] == 'n')
{
/* JCOCA & JCOCB is turned off*/
zgradpulse(gzlvl3, gt3);
delay(epsilon/4.0-pwS7*0.5-gt3);
c_simshapedpulse(shname2,80.0,150.0,0.0,0.0,zero,zero,zero, 2.0e-6, 2.0e-6);
delay(had2*0.5-pwS4*0.5-epsilon/4.0-pwS7*0.5);
c_simshapedpulse("isnob5",80.0,0.0,pw*2.0,0.0,zero,zero,zero, 2.0e-6, 2.0e-6);
zgradpulse(gzlvl3, gt3);
delay(had2*0.5-pwS4*0.5-gt3);
rgpulse(pw*flip_angle/90.0, t1, 0.0, 0.0);
if (flip_angle < 90.0) delay(pw*(1-flip_angle/90.0));
if (had3*0.5-shpw1*0.5-epsilon/4.0-pwS7*0.5>0.0)
{
zgradpulse(gzlvl3, 1.1*gt3);
delay(epsilon/4.0-pwS7*0.5-1.1*gt3);
c_simshapedpulse(shname2,80.0,150.0,0.0,0.0,zero,zero,zero, 2.0e-6, 2.0e-6);
delay(had3*0.5-shpw1*0.5-epsilon/4.0-pwS7*0.5);
shaped_pulse(shname1,shpw1,two,0.0,0.0);
delay((tauC3-(had2+pw*120/90*2))*0.5-pwS4*0.5-had3*0.5-shpw1*0.5);
}
else
{
zgradpulse(gzlvl3, 1.1*gt3);
delay(had3*0.5-shpw1*0.5-1.1*gt3);
shaped_pulse(shname1,shpw1,two,0.0,0.0);
delay(epsilon/4.0-pwS7*0.5-had3*0.5-shpw1*0.5);
c_simshapedpulse(shname2,80.0,150.0,0.0,0.0,zero,zero,zero, 2.0e-6, 2.0e-6);
delay((tauC3-(had2+pw*120/90*2))*0.5-pwS4*0.5-epsilon/4.0-pwS7*0.5);
}
c_shapedpulse("isnob5",80.0,0.0,two, 2.0e-6, 2.0e-6);
zgradpulse(gzlvl3, 1.1*gt3);
delay((tauC3-(had2+pw*120/90*2))*0.5-pwS4*0.5-1.1*gt3);
}
if (fil_flg1[0] == 'c')
{
/* JCOCA & JCOCB is turned off*/
zgradpulse(gzlvl3, gt3);
delay(had2*0.5-pwS4*0.5-gt3);
c_simshapedpulse("isnob5",80.0,0.0,pw*2.0,0.0,zero,zero,zero, 2.0e-6, 2.0e-6);
zgradpulse(gzlvl3, gt3);
delay(had2*0.5-pwS4*0.5-gt3);
rgpulse(pw*flip_angle/90.0, t1, 0.0, 0.0);
if (flip_angle < 90.0) delay(pw*(1-flip_angle/90.0));
zgradpulse(gzlvl3, 1.1*gt3);
delay(had3*0.5-shpw1*0.5-1.1*gt3);
shaped_pulse(shname1,shpw1,two,0.0,0.0);
delay((tauC3-(had2+pw*120.0/90.0*2.0))*0.5-pwS4*0.5-had3*0.5-shpw1*0.5);
c_shapedpulse("isnob5",80.0,0.0,two, 2.0e-6, 2.0e-6);
zgradpulse(gzlvl3, 1.1*gt3);
delay((tauC3-(had2+pw*120.0/90.0*2.0))*0.5-pwS4*0.5-1.1*gt3);
}
/*********************************** 2nd transfer CB->CA +DEPT CAH ***********/
decrgpulse(pwC, zero, 0.0, 0.0);
c13pulse("co", "ca", "sinc", 180.0, zero, 0.0, 0.0);
delay(tauC1-pwS3-pwS4*0.5);
c_shapedpulse("reburp",80.0,0.0,zero, 2.0e-6, 2.0e-6);
delay(tauC1-tauC2-pwS3-pwS4*0.5);
c13pulse("co", "ca", "sinc", 180.0, zero, 0.0, 0.0);
delay(tauC2-pw*8.0-had1);
shaped_pulse(shname1,shpw1,two,0.0,0.0);
delay(had1);
c13pulse("cab", "co", "square", 90.0, zero, 0.0, 0.0);
/******************************************************************************/
if(dm3[B] == 'y') /*optional 2H decoupling off */
{dec3rgpulse(1/dmf3, three, 0.0, 0.0); dec3blank();
setstatus(DEC3ch, FALSE, 'w', FALSE, dmf3); dec3blank();}
zgradpulse(gzlvl3, gt3);
delay(2.0e-4);
h1decon("DIPSI2", 27.0, 0.0);/*POWER_DELAY+PWRF_DELAY+PRG_START_DELAY */
c13pulse("co", "ca", "sinc", 90.0, t5, 2.0e-6, 0.0); /* point e */
decphase(zero);
delay(eta - 2.0*POWER_DELAY - 2.0*PWRF_DELAY);
/* 2*POWER_DELAY+2*PWRF_DELAY */
c13pulse("ca", "co", "square", 180.0, zero, 2.0e-6, 0.0); /* pwS2 */
dec2phase(zero);
delay(theta - eta - pwS2 - WFG3_START_DELAY);
/* WFG3_START_DELAY */
sim3_c13pulse("", "co", "ca", "sinc", "", 0.0, 180.0, 2.0*pwN,
zero, zero, zero, 2.0e-6, 2.0e-6);
initval(phi7cal, v7);
decstepsize(1.0);
dcplrphase(v7); /* SAPS_DELAY */
dec2phase(t8);
delay(theta - SAPS_DELAY);
if (SE_flg[0]=='y') /* point f */
{
nh_evol_se_train("co", "ca"); /* common part of sequence in bionmr.h */
if (dm3[B]=='y') lk_sample();
}
else
{
nh_evol_train("co", "ca"); /* common part of sequence in bionmr.h */
if (dm3[B]=='y') lk_sample();
}
}
pulsesequence()
{
/* DECLARE VARIABLES */
char autocal[MAXSTR], /* auto-calibration flag */
fsat[MAXSTR],
fscuba[MAXSTR],
f1180[MAXSTR], /* Flag to start t1 @ halfdwell */
f2180[MAXSTR], /* Flag to start t2 @ halfdwell */
f3180[MAXSTR], /* Flag to start t3 @ halfdwell */
fco180[MAXSTR], /* Flag for checking sequence */
fca180[MAXSTR], /* Flag for checking sequence */
spca180[MAXSTR], /* string for the waveform Ca 180 */
spco180[MAXSTR], /* string for the waveform Co 180 */
spchirp[MAXSTR], /* string for the waveform reburp 180 */
ddseq[MAXSTR], /* 2H decoupling seqfile */
shp_sl[MAXSTR], /* string for seduce shape */
sel_flg[MAXSTR];
int phase, phase2, phase3, ni2, ni3, icosel,
t1_counter, /* used for states tppi in t1 */
t2_counter, /* used for states tppi in t2 */
t3_counter; /* used for states tppi in t3 */
double tau1, /* t1 delay */
tau2, /* t2 delay */
tau3, /* t2 delay */
taua, /* ~ 1/4JNH = 2.25 ms */
taub, /* ~ 1/4JNH = 2.25 ms */
zeta, /* time for C'-N to refocuss set to 0.5*24.0 ms */
bigTN, /* nitrogen T period */
pwc90, /* PW90 for c nucleus @ d_c90 */
pwc180on, /* PW180 at @ d_c180 */
pwchirp, /* PW180 for ca nucleus @ d_creb */
pwc180off, /* PW180 at d_c180 + pad */
tsatpwr, /* low level 1H trans.power for presat */
d_c90, /* power level for 13C pulses(pwc90 = sqrt(15)/4delta)
delta is the separation between Ca and Co */
d_c180, /* power level for 180 13C pulses
(pwc180on=sqrt(3)/2delta */
d_chirp,
sw1, /* sweep width in f1 */
sw2, /* sweep width in f2 */
sw3, /* sweep width in f3 */
pw_sl, /* pw90 for H selective pulse on water ~ 2ms */
phase_sl, /* phase for pw_sl */
tpwrsl, /* power level for square pw_sl */
pwDlvl, /* Power for D decoupling */
pwD, /* pw90 at pwDlvl */
pwC, pwClvl, /* C-13 calibration */
compC,
pwN, /* PW90 for 15N pulse */
pwNlvl, /* high dec2 pwr for 15N hard pulses */
gstab, /* delay to compensate for gradient gt5 */
gt1,
gt2,
gt3,
gt4,
gt5,
gt6,
gt7,
gt8,
gt9,
gzlvl1,
gzlvl2,
gzlvl3,
gzlvl4,
gzlvl5,
gzlvl6,
gzlvl7,
gzlvl8,
gzlvl9;
/* LOAD VARIABLES */
getstr("autocal",autocal);
getstr("fsat",fsat);
getstr("fco180",fco180);
getstr("fca180",fca180);
getstr("f1180",f1180);
getstr("f2180",f2180);
getstr("f3180",f3180);
getstr("fscuba",fscuba);
getstr("ddseq",ddseq);
getstr("shp_sl",shp_sl);
getstr("sel_flg",sel_flg);
taua = getval("taua");
taub = getval("taub");
zeta = getval("zeta");
bigTN = getval("bigTN");
tpwr = getval("tpwr");
tsatpwr = getval("tsatpwr");
dpwr = getval("dpwr");
pwN = getval("pwN");
pwNlvl = getval("pwNlvl");
pwD = getval("pwD");
pwDlvl = getval("pwDlvl");
phase = (int) ( getval("phase") + 0.5);
phase2 = (int) ( getval("phase2") + 0.5);
phase3 = (int) ( getval("phase3") + 0.5);
sw1 = getval("sw1");
sw2 = getval("sw2");
sw3 = getval("sw3");
ni2 = getval("ni2");
ni3 = getval("ni3");
pw_sl = getval("pw_sl");
phase_sl = getval("phase_sl");
tpwrsl = getval("tpwrsl");
gstab = getval("gstab");
gt1 = getval("gt1");
if (getval("gt2") > 0) gt2=getval("gt2");
else gt2=gt1*0.1;
gt3 = getval("gt3");
gt4 = getval("gt4");
gt5 = getval("gt5");
gt6 = getval("gt6");
gt7 = getval("gt7");
gt8 = getval("gt8");
gt9 = getval("gt9");
gzlvl1 = getval("gzlvl1");
gzlvl2 = getval("gzlvl2");
gzlvl3 = getval("gzlvl3");
gzlvl4 = getval("gzlvl4");
gzlvl5 = getval("gzlvl5");
gzlvl6 = getval("gzlvl6");
gzlvl7 = getval("gzlvl7");
gzlvl8 = getval("gzlvl8");
gzlvl9 = getval("gzlvl9");
if(autocal[0]=='n')
{
getstr("spca180",spca180);
getstr("spco180",spco180);
getstr("spchirp",spchirp);
pwc90 = getval("pwc90");
pwc180on = getval("pwc180on");
pwc180off = getval("pwc180off");
d_c90 = getval("d_c90");
d_c180 = getval("d_c180");
pwchirp = getval("pwchirp");
d_chirp = getval("d_chirp");
}
else
{
strcpy(spca180,"Phard180ca");
strcpy(spco180,"Phard180co");
strcpy(spchirp,"Pchirp180");
if (FIRST_FID)
{
pwC = getval("pwC");
compC = getval("compC");
pwClvl = getval("pwClvl");
co90 = pbox("cal", CO90, CO180ps, dfrq, pwC*compC, pwClvl);
co180 = pbox("cal", CO180, CO180ps, dfrq, pwC*compC, pwClvl);
ca180 = pbox(spca180, CA180, CA180ps, dfrq, pwC*compC, pwClvl);
co180a = pbox(spco180, CO180a, CA180ps, dfrq, pwC*compC, pwClvl);
chirp = pbox(spchirp, CHIRP, CHIRPps, dfrq, pwC*compC, pwClvl);
}
pwc90 = co90.pw; d_c90 = co90.pwr;
pwc180on = co180.pw; d_c180 = co180.pwr;
pwc180off = ca180.pw;
pwchirp = chirp.pw; d_chirp = chirp.pwr;
}
/* LOAD PHASE TABLE */
settable(t1,2,phi1);
settable(t2,2,phi2);
settable(t3,4,phi3);
settable(t4,1,phi4);
settable(t5,4,phi5);
settable(t6,4,rec);
/* CHECK VALIDITY OF PARAMETER RANGES */
if( bigTN - (ni3-1)*0.5/sw3 - WFG3_START_DELAY < 0.2e-6 )
{
text_error(" ni3 is too big\n");
text_error(" please set ni3 smaller or equal to %d\n",
(int) ((bigTN -WFG3_START_DELAY)*sw3*2.0) +1 );
psg_abort(1);
}
if((dm[A] == 'y' || dm[B] == 'y' || dm[C] == 'y' || dm[D] == 'y' ))
{
text_error("incorrect dec1 decoupler flags! ");
psg_abort(1);
}
if((dm2[A] == 'y' || dm2[B] == 'y' || dm2[C] == 'y' || dm2[D] == 'y'))
{
text_error("incorrect dec2 decoupler flags! Should be 'nnnn' ");
psg_abort(1);
}
if( tsatpwr > 6 )
{
text_error("TSATPWR too large !!! ");
psg_abort(1);
}
if( dpwr > 46 )
{
text_error("don't fry the probe, DPWR too large! ");
psg_abort(1);
}
if( dpwr2 > 46 )
{
text_error("don't fry the probe, DPWR2 too large! ");
psg_abort(1);
}
if( dpwr3 > 50 )
{
text_error("don't fry the probe, dpwr3 too large! ");
psg_abort(1);
}
if( d_c90 > 62 )
{
text_error("don't fry the probe, DHPWR too large! ");
psg_abort(1);
}
if( pw > 200.0e-6 )
{
text_error("dont fry the probe, pw too high ! ");
psg_abort(1);
}
if( pwN > 200.0e-6 )
{
text_error("dont fry the probe, pwN too high ! ");
psg_abort(1);
}
if( pwc90 > 200.0e-6 )
{
text_error("dont fry the probe, pwc90 too high ! ");
psg_abort(1);
}
if( pwc180off > 200.0e-6 )
{
text_error("dont fry the probe, pwc180 too high ! ");
psg_abort(1);
}
if( gt3 > 2.5e-3 )
{
text_error("gt3 is too long\n");
psg_abort(1);
}
if( gt1 > 10.0e-3 || gt2 > 10.0e-3 || gt4 > 10.0e-3 || gt5 > 10.0e-3
|| gt6 > 10.0e-3 || gt7 > 10.0e-3 || gt8 > 10.0e-3
|| gt9 > 10.0e-3)
{
text_error("gt values are too long. Must be < 10.0e-3 or gt11=50us\n");
psg_abort(1);
}
if((fca180[A] == 'y') && (ni2 > 1))
{
text_error("must set fca180='n' to allow Calfa evolution (ni2>1)\n");
psg_abort(1);
}
if((fco180[A] == 'y') && (ni > 1))
{
text_error("must set fco180='n' to allow CO evolution (ni>1)\n");
psg_abort(1);
}
/* Phase incrementation for hypercomplex 2D data */
if (phase == 2) tsadd(t1,1,4);
if (phase2 == 2) tsadd(t5,1,4);
if (phase3 == 2) { tsadd(t4, 2, 4); icosel = 1; }
else icosel = -1;
/* Set up f1180 tau1 = t1 */
tau1 = d2;
if((f1180[A] == 'y') && (ni > 1)) {
if (pwc180off > 2.0*pwN)
tau1 += (1.0/(2.0*sw1) - 4.0*pwc90/PI - pwc180off
- WFG3_START_DELAY - WFG3_STOP_DELAY - 4.0e-6 - 2.0*POWER_DELAY - 4.0e-6);
else
tau1 += (1.0/(2.0*sw1) - 4.0*pwc90/PI - 2.0*pwN
- WFG3_START_DELAY - WFG3_STOP_DELAY - 4.0e-6 - 2.0*POWER_DELAY - 4.0e-6);
if(tau1 < 0.2e-6) {
tau1 = 0.4e-6;
text_error("tau1 could be negative");
}
}
else
{
if (pwc180off > 2.0*pwN)
tau1 = tau1 - 4.0*pwc90/PI - pwc180off
- WFG3_START_DELAY - WFG3_STOP_DELAY - 4.0e-6 - 2.0*POWER_DELAY - 4.0e-6;
else
tau1 = tau1 - 4.0*pwc90/PI - 2.0*pwN
- WFG3_START_DELAY - WFG3_STOP_DELAY - 4.0e-6 - 2.0*POWER_DELAY - 4.0e-6;
if(tau1 < 0.2e-6) tau1 = 0.4e-6;
}
tau1 = tau1/2.0;
/* Set up f2180 tau2 = t2 */
tau2 = d3;
if((f2180[A] == 'y') && (ni2 > 1)) {
if (pwc180off > 2.0*pwN)
tau2 += ( 1.0 / (2.0*sw2) - 4.0*pwc90/PI - 4.0e-6
- 2.0*POWER_DELAY
- WFG3_START_DELAY - pwc180off - WFG3_STOP_DELAY - 4.0e-6);
else
tau2 += ( 1.0 / (2.0*sw2) - 4.0*pwc90/PI - 4.0e-6
- 2.0*POWER_DELAY
- WFG3_START_DELAY - 2.0*pwN - WFG3_STOP_DELAY - 4.0e-6);
if(tau2 < 0.2e-6) {
tau2 = 0.4e-6;
text_error("tau2 could be negative");
}
}
else
{
if (pwc180off > 2.0*pwN)
tau2 = tau2 - 4.0*pwc90/PI - 4.0e-6
- 2.0*POWER_DELAY
- WFG3_START_DELAY - pwc180off - WFG3_STOP_DELAY - 4.0e-6;
else
tau2 = tau2 - 4.0*pwc90/PI - 4.0e-6
- 2.0*POWER_DELAY
- WFG3_START_DELAY - 2.0*pwN - WFG3_STOP_DELAY - 4.0e-6;
if(tau2 < 0.2e-6) tau2 = 0.4e-6;
}
tau2 = tau2/2.0;
/* Set up f3180 tau3 = t3 */
tau3 = d4;
if ((f3180[A] == 'y') && (ni3 > 1)) {
tau3 += ( 1.0 / (2.0*sw3) );
if(tau3 < 0.2e-6) tau3 = 0.4e-6;
}
tau3 = tau3/2.0;
/* Calculate modifications to phases for States-TPPI acquisition */
if( ix == 1) d2_init = d2 ;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if(t1_counter % 2) {
tsadd(t1,2,4);
tsadd(t6,2,4);
}
if( ix == 1) d3_init = d3 ;
t2_counter = (int) ( (d3-d3_init)*sw2 + 0.5 );
if(t2_counter % 2) {
tsadd(t5,2,4);
tsadd(t6,2,4);
}
if( ix == 1) d4_init = d4 ;
t3_counter = (int) ( (d4-d4_init)*sw3 + 0.5 );
if(t3_counter % 2) {
tsadd(t2,2,4);
tsadd(t6,2,4);
}
/* BEGIN ACTUAL PULSE SEQUENCE */
status(A);
obsoffset(tof);
decoffset(dof); /* set Dec1 carrier at Co */
obspower(tsatpwr); /* Set transmitter power for 1H presaturation */
decpower(d_chirp); /* Set Dec1 power for hard 13C pulses */
dec2power(pwNlvl); /* Set Dec2 power for 15N hard pulses */
/* Presaturation Period */
if (fsat[0] == 'y')
{
delay(2.0e-5);
rgpulse(d1,zero,2.0e-6,2.0e-6); /* presaturation */
obspower(tpwr); /* Set transmitter power for hard 1H pulses */
delay(2.0e-5);
if (fscuba[0] == 'y')
{
delay(2.2e-2);
rgpulse(pw,zero,2.0e-6,0.0);
rgpulse(2*pw,one,2.0e-6,0.0);
rgpulse(pw,zero,2.0e-6,0.0);
delay(2.2e-2);
}
}
else
{
delay(d1);
}
obspower(tpwr); /* Set transmitter power for hard 1H pulses */
txphase(zero);
dec2phase(zero);
delay(1.0e-5);
/* Begin Pulses */
status(B);
rcvroff();
lk_hold();
delay(20.0e-6);
initval(1.0,v2);
obsstepsize(phase_sl);
xmtrphase(v2);
/* shaped pulse */
obspower(tpwrsl);
shaped_pulse(shp_sl,pw_sl,one,4.0e-6,0.0);
xmtrphase(zero);
obspower(tpwr); txphase(zero);
delay(4.0e-6);
/* shaped pulse */
rgpulse(pw,zero,0.0,0.0); /* 90 deg 1H pulse */
delay(0.2e-6);
zgradpulse(gzlvl5,gt5);
delay(2.0e-6);
delay(taua - gt5 - 2.2e-6); /* taua <= 1/4JNH */
sim3pulse(2*pw,0.0e-6,2*pwN,zero,zero,zero,0.0,0.0);
txphase(three); dec2phase(zero); decphase(zero);
delay(0.2e-6);
zgradpulse(gzlvl5,gt5);
delay(200.0e-6);
delay(taua - gt5 - 200.2e-6 - 2.0e-6);
if (sel_flg[A] == 'n')
{
rgpulse(pw,three,2.0e-6,0.0);
delay(0.2e-6);
zgradpulse(gzlvl3,gt3);
delay(200.0e-6);
dec2rgpulse(pwN,zero,0.0,0.0);
delay( zeta );
dec2rgpulse(2.0*pwN,zero,0.0,0.0);
decshaped_pulse(spchirp,pwchirp,zero,0.0,0.0);
delay(zeta -WFG_START_DELAY -pwchirp -WFG_STOP_DELAY -2.0e-6);
dec2rgpulse(pwN,zero,2.0e-6,0.0);
}
else
{
rgpulse(pw,one,2.0e-6,0.0);
initval(1.0,v3);
dec2stepsize(45.0);
dcplr2phase(v3);
delay(0.2e-6);
zgradpulse(gzlvl3,gt3);
delay(200.0e-6);
dec2rgpulse(pwN,zero,0.0,0.0);
dcplr2phase(zero);
delay(1.34e-3 - SAPS_DELAY - 2.0*pw);
rgpulse(pw,one,0.0,0.0);
rgpulse(2.0*pw,zero,0.0,0.0);
rgpulse(pw,one,0.0,0.0);
delay( zeta - 1.34e-3 - 2.0*pw);
dec2rgpulse(2.0*pwN,zero,0.0,0.0);
decshaped_pulse(spchirp,pwchirp,zero,0.0,0.0);
delay(zeta -WFG_START_DELAY -pwchirp -WFG_STOP_DELAY -2.0e-6);
dec2rgpulse(pwN,zero,2.0e-6,0.0);
}
dec2phase(zero); decphase(t1);
decpower(d_c90);
delay(0.2e-6);
zgradpulse(gzlvl8,gt8);
delay(200.0e-6);
decrgpulse(pwc90,t1,2.0e-6,0.0);
/* t1 period for Co evolution begins */
if (fco180[A]=='n')
{
decpower(d_c180);
delay(tau1);
sim3shaped_pulse("",spca180,"",0.0,pwc180off,2.0*pwN,zero,zero,zero,4.0e-6,0.0);
decpower(d_c90);
delay(tau1);
}
else /* for checking sequence */
{
decpower(d_c180);
decrgpulse(pwc180on,zero,4.0e-6,0.0);
decpower(d_c90);
}
/* t1 period for Co evolution ends */
decrgpulse(pwc90,zero,4.0e-6,0.0);
decoffset(dof-(174-56)*dfrq); /* change Dec1 carrier to Ca (55 ppm) */
delay(0.2e-6);
zgradpulse(gzlvl4,gt4);
delay(150.0e-6);
/* Turn on D decoupling using the third decoupler */
dec3phase(one);
dec3power(pwDlvl);
dec3rgpulse(pwD,one,4.0e-6,0.0);
dec3phase(zero);
dec3power(dpwr3);
dec3unblank();
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
/* Turn on D decoupling */
decrgpulse(pwc90,t5,2.0e-6,0.0);
/* t2 period for Ca evolution begins */
if (fca180[A]=='n')
{
decphase(zero); dec2phase(zero);
decpower(d_c180);
delay(tau2);
sim3shaped_pulse("",spco180,"",0.0,pwc180off,2.0*pwN,zero,zero,zero,4.0e-6,0.0);
decpower(d_c90);
delay(tau2);
}
else /* for checking sequence */
{
decpower(d_c180);
decrgpulse(pwc180on,zero,4.0e-6,0.0);
decpower(d_c90);
}
/* t2 period for Ca evolution ends */
decrgpulse(pwc90,zero,4.0e-6,0.0);
/* Turn off D decoupling */
setstatus(DEC3ch, FALSE, 'c', FALSE, dmf3);
dec3blank();
dec3phase(three);
dec3power(pwDlvl);
dec3rgpulse(pwD,three,4.0e-6,0.0);
/* Turn off D decoupling */
decoffset(dof); /* set carrier back to Co */
decpower(d_chirp);
delay(0.2e-6);
zgradpulse(gzlvl9,gt9);
delay(150.0e-6);
/* t3 period begins */
dec2rgpulse(pwN,t2,2.0e-6,0.0);
dec2phase(t3);
delay(bigTN - tau3);
dec2rgpulse(2.0*pwN,t3,0.0,0.0);
decshaped_pulse(spchirp,pwchirp,zero,0.0,0.0);
txphase(zero);
dec2phase(t4);
delay(0.2e-6);
zgradpulse(gzlvl1,gt1);
delay(500.0e-6);
delay(bigTN - WFG_START_DELAY - pwchirp - WFG_STOP_DELAY
-gt1 -500.2e-6 -2.0*GRADIENT_DELAY);
delay(tau3);
sim3pulse(pw,0.0e-6,pwN,zero,zero,t4,0.0,0.0);
/* t3 period ends */
decpower(d_c90);
decrgpulse(pwc90,zero,4.0e-6,0.0);
decoffset(dof-(174-56)*dfrq);
decrgpulse(pwc90,zero,20.0e-6,0.0);
delay(0.2e-6);
zgradpulse(gzlvl6,gt6);
delay(2.0e-6);
dec2phase(zero);
delay(taub - POWER_DELAY - 4.0e-6 - pwc90 - 20.0e-6 - pwc90 - gt6 - 2.2e-6);
sim3pulse(2*pw,0.0e-6,2*pwN,zero,zero,zero,0.0,0.0);
decoffset(dof);
delay(0.2e-6);
zgradpulse(gzlvl6,gt6);
delay(200.0e-6);
txphase(one);
dec2phase(one);
delay(taub - gt6 - 200.2e-6);
sim3pulse(pw,0.0e-6,pwN,one,zero,one,0.0,0.0);
delay(0.2e-6);
zgradpulse(gzlvl7,gt7);
delay(2.0e-6);
txphase(zero);
dec2phase(zero);
delay(taub - gt7 - 2.2e-6);
sim3pulse(2*pw,0.0e-6,2*pwN,zero,zero,zero,0.0,0.0);
delay(0.2e-6);
zgradpulse(gzlvl7,gt7);
delay(200.0e-6);
delay(taub - gt7 - 200.2e-6);
sim3pulse(pw,0.0e-6,pwN,zero,zero,zero,0.0,0.0);
delay(gt2 +gstab -0.5*(pwN -pw) -2.0*pw/PI);
rgpulse(2*pw,zero,0.0,0.0);
delay(2.0e-6);
zgradpulse(icosel*gzlvl2,gt2);
decpower(dpwr);
dec2power(dpwr2);
delay(gstab -2.0e-6 -2.0*GRADIENT_DELAY -2.0*POWER_DELAY);
lk_sample();
/* BEGIN ACQUISITION */
status(C);
setreceiver(t6);
}
pulsesequence()
{
/* DECLARE AND LOAD VARIABLES */
char f1180[MAXSTR], /* Flag to start t1 @ halfdwell */
f2180[MAXSTR], /* Flag to start t2 @ halfdwell */
mag_flg[MAXSTR], /* magic-angle coherence transfer gradients */
SCT[MAXSTR], /* Semi-constant time flag for N-15 evolution */
CT_c[MAXSTR], /* Constant time flag for C-13 evolution */
TROSY[MAXSTR]; /* do TROSY on N15 and H1 */
int icosel, /* used to get n and p type */
t1_counter, /* used for states tppi in t1 */
t2_counter, /* used for states tppi in t2 */
PRexp, /* projection-reconstruction flag */
ni2 = getval("ni2");
double tau1, /* t1 delay */
tau2, /* t2 delay */
tauC = getval("tauC"), /* delay for CO to Ca evolution */
timeTN = getval("timeTN"), /* constant time for 15N evolution */
timeTC = getval("timeTC"), /* constant time for 13C evolution */
t2a=0.0, t2b=0.0, halfT2=0.0, CTdelay=0.0,
kappa = 5.4e-3,
lambda = 2.4e-3,
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
rf0, /* maximum fine power when using pwC pulses */
/* 90 degree pulse at Ca (56ppm), first off-resonance null at CO (174ppm) */
pwC1, /* 90 degree pulse length on C13 at rf1 */
rf1, /* fine power for 4.7 kHz rf for 600MHz magnet */
/* 180 degree pulse at Ca (56ppm), first off-resonance null at CO(174ppm) */
pwC2, /* 180 degree pulse length at rf2 */
rf2, /* fine power for 10.5 kHz rf for 600MHz magnet */
/* the following pulse lengths for SLP pulses are automatically calculated */
/* by the macro "proteincal". SLP pulse shapes, "offC6" etc are called */
/* directly from your shapelib. */
pwC3 = getval("pwC3"), /*180 degree pulse at Ca(56ppm) null at CO(174ppm) */
pwC6 = getval("pwC6"), /* 90 degree selective sinc pulse on CO(174ppm) */
pwC8 = getval("pwC8"), /* 180 degree selective sinc pulse on CO(174ppm) */
pwC9 = getval("pwC9"), /* 180 degree selective sinc pulse on CO(174ppm) */
phshift9, /* phase shift induced on Ca by pwC9 ("offC9") pulse */
pwZ, /* the largest of pwC9 and 2.0*pwN */
pwZ1, /* the larger of pwC8 and 2.0*pwN for 1D experiments */
rf3, /* fine power for the pwC3 ("offC3") pulse */
rf6, /* fine power for the pwC6 ("offC6") pulse */
rf8, /* fine power for the pwC8 ("offC8") pulse */
rf9, /* fine power for the pwC9 ("offC9") pulse */
dofCO, /* channel 2 offset for most CO pulses */
compH = getval("compH"), /* adjustment for C13 amplifier compression */
compC = getval("compC"), /* adjustment for C13 amplifier compression */
pwHs = getval("pwHs"), /* H1 90 degree pulse length at tpwrs */
tpwrsf = getval("tpwrsf"), /* fine power adjustment for flipback */
tpwrs, /* power for the pwHs ("H2Osinc") pulse */
csa, sna,
pra = M_PI*getval("pra")/180.0,
pwHd, /* H1 90 degree pulse length at tpwrd */
tpwrd, /* rf for WALTZ decoupling */
waltzB1 = getval("waltzB1"), /* waltz16 field strength (in Hz) */
pwNlvl = getval("pwNlvl"), /* power for N15 pulses */
pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */
sw1 = getval("sw1"),
sw2 = getval("sw2"),
gt1 = getval("gt1"), /* coherence pathway gradients */
gzcal = getval("gzcal"), /* g/cm to DAC conversion factor */
gzlvl1 = getval("gzlvl1"),
gzlvl2 = getval("gzlvl2"),
gt0 = getval("gt0"), /* other gradients */
gt3 = getval("gt3"),
gt4 = getval("gt4"),
gt5 = getval("gt5"),
gt7 = getval("gt7"),
gt9 = getval("gt9"),
gt10 = getval("gt10"),
gstab = getval("gstab"),
gzlvl0 = getval("gzlvl0"),
gzlvl3 = getval("gzlvl3"),
gzlvl4 = getval("gzlvl4"),
gzlvl5 = getval("gzlvl5"),
gzlvl6 = getval("gzlvl6"),
gzlvl7 = getval("gzlvl7"),
gzlvl8 = getval("gzlvl8"),
gzlvl9 = getval("gzlvl9"),
gzlvl10 = getval("gzlvl10");
getstr("f1180",f1180);
getstr("f2180",f2180);
getstr("mag_flg",mag_flg);
getstr("SCT",SCT);
getstr("CT_c",CT_c);
getstr("TROSY",TROSY);
/* LOAD PHASE TABLE */
settable(t3,2,phi3);
settable(t4,1,phx);
settable(t5,4,phi5);
if (TROSY[A]=='y')
{settable(t8,1,phy);
settable(t9,1,phx);
settable(t10,1,phy);
settable(t11,1,phx);
settable(t12,4,recT);}
else
{settable(t8,1,phx);
settable(t9,8,phi9);
settable(t10,1,phx);
settable(t11,1,phy);
settable(t12,4,rec);}
/* INITIALIZE VARIABLES */
if( dpwrf < 4095 )
{ printf("reset dpwrf=4095 and recalibrate C13 90 degree pulse");
psg_abort(1); }
/* offset during CO pulses, except for t1 evolution period */
dofCO = dof + 118.0*dfrq;
/* maximum fine power for pwC pulses */
rf0 = 4095.0;
/* 90 degree pulse on Ca, null at CO 118ppm away */
pwC1 = sqrt(15.0)/(4.0*118.0*dfrq);
rf1 = 4095.0*(compC*pwC)/pwC1;
rf1 = (int) (rf1 + 0.5);
/* 180 degree pulse on Ca, null at CO 118ppm away */
pwC2 = sqrt(3.0)/(2.0*118.0*dfrq);
rf2 = (compC*4095.0*pwC*2.0)/pwC2;
rf2 = (int) (rf2 + 0.5);
if( rf2 > 4095.0 )
{ printf("increase pwClvl so that C13 90 < 24us*(600/sfrq)"); psg_abort(1);}
/* 180 degree pulse on Ca, null at CO 118ppm away */
rf3 = (compC*4095.0*pwC*2.0)/pwC3;
rf3 = (int) (rf3 + 0.5);
/* 90 degree one-lobe sinc pulse on CO, null at Ca 118ppm away */
rf6 = (compC*4095.0*pwC*1.69)/pwC6; /* needs 1.69 times more */
rf6 = (int) (rf6 + 0.5); /* power than a square pulse */
/* 180 degree one-lobe sinc pulse on CO, null at Ca 118ppm away */
rf8 = (compC*4095.0*pwC*2.0*1.65)/pwC8; /* needs 1.65 times more */
rf8 = (int) (rf8 + 0.5); /* power than a square pulse */
/* 180 degree one-lobe sinc pulse on CO, null at Ca 118ppm away */
rf9 = (compC*4095.0*pwC*2.0*1.65)/pwC8; /* needs 1.65 times more */
rf9 = (int) (rf9 + 0.5); /* power than a square pulse */
/* the pwC9 pulse at the middle of t1 */
if ((ni2 > 0.0) && (ni == 1.0)) ni = 0.0;
if (pwC8 > 2.0*pwN) pwZ = pwC8; else pwZ = 2.0*pwN;
if ((pwC9==0.0) && (pwC8>2.0*pwN)) pwZ1=pwC8-2.0*pwN; else pwZ1=0.0;
if ( ni > 1 ) pwC9 = pwC8;
if ( pwC9 > 0 ) phshift9 = 140.0;
else phshift9 = 0.0;
/* selective H20 one-lobe sinc pulse */
tpwrs = tpwr - 20.0*log10(pwHs/(compH*pw*1.69)); /* needs 1.69 times more */
tpwrs = (int) (tpwrs); /* power than a square pulse */
/* power level and pulse time for WALTZ 1H decoupling */
pwHd = 1/(4.0 * waltzB1) ; /* 7.5 kHz rf */
tpwrd = tpwr - 20.0*log10(pwHd/(compH*pw));
tpwrd = (int) (tpwrd + 0.5);
/* set up Projection-Reconstruction experiment */
tau1 = d2; tau2 = d3;
PRexp=0; csa = 1.0; sna = 0.0;
if((pra > 0.0) && (pra < 90.0)) /* PR experiments */
{
PRexp = 1;
csa = cos(pra);
sna = sin(pra);
tau1 = d2*csa;
tau2 = d2*sna;
}
/* CHECK VALIDITY OF PARAMETER RANGES */
if(SCT[A] == 'n')
{
if (PRexp)
{
if( 0.5*ni*sna/sw1 > timeTN - WFG3_START_DELAY)
{ printf(" ni is too big. Make ni equal to %d or less.\n",
((int)((timeTN - WFG3_START_DELAY)*2.0*sw1/sna))); psg_abort(1);}
}
else
{
if ( 0.5*ni2*1/(sw2) > timeTN - WFG3_START_DELAY)
{ printf(" ni2 is too big. Make ni2 equal to %d or less.\n",
((int)((timeTN - WFG3_START_DELAY)*2.0*sw2))); psg_abort(1);}
}
}
if(CT_c[A] == 'y')
{
if ( 0.5*ni*csa/sw1 > timeTC)
{ printf(" ni is too big. Make ni less than %d or less.\n",
((int)(timeTC*2.0*sw1/csa - 4e-6 - SAPS_DELAY))); psg_abort(1);}
}
if ( tauC < (gt7+1.0e-4+0.5*10.933*pwC)) gt7=(tauC-1.0e-4-0.5*10.933*pwC);
if ( dm[A] == 'y' || dm[B] == 'y' || dm[C] == 'y' )
{ printf("incorrect dec1 decoupler flags! Should be 'nnn' "); psg_abort(1);}
if ( dm2[A] == 'y' || dm2[B] == 'y' )
{ printf("incorrect dec2 decoupler flags! Should be 'nny' "); psg_abort(1);}
if ( dm3[A] == 'y' || dm3[C] == 'y' )
{ printf("incorrect dec3 decoupler flags! Should be 'nyn' or 'nnn' ");
psg_abort(1);}
if ( dpwr2 > 50 )
{ printf("dpwr2 too large! recheck value "); psg_abort(1);}
if ( pw > 20.0e-6 )
{ printf(" pw too long ! recheck value "); psg_abort(1);}
if ( pwN > 100.0e-6 )
{ printf(" pwN too long! recheck value "); psg_abort(1);}
if ( TROSY[A]=='y' && dm2[C] == 'y')
{ text_error("Choose either TROSY='n' or dm2='n' ! "); psg_abort(1);}
/* PHASES AND INCREMENTED TIMES */
/* Phase incrementation for hypercomplex 2D data, States-Haberkorn element */
if (phase1 == 2) tsadd(t3,1,4);
if (TROSY[A]=='y')
{ if (phase2 == 2) icosel = +1;
else {tsadd(t4,2,4); tsadd(t10,2,4); icosel = -1;}
}
else { if (phase2 == 2) {tsadd(t10,2,4); icosel = +1;}
else icosel = -1;
}
/* Calculate modifications to phases for States-TPPI acquisition */
if( ix == 1) d2_init = d2;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if(t1_counter % 2)
{ tsadd(t3,2,4); tsadd(t12,2,4); }
if( ix == 1) d3_init = d3;
t2_counter = (int) ( (d3-d3_init)*sw2 + 0.5 );
if(t2_counter % 2)
{ tsadd(t8,2,4); tsadd(t12,2,4); }
/* Set up CONSTANT/SEMI-CONSTANT time evolution in N15 */
halfT2 = 0.0;
CTdelay = timeTN + pwC8 + WFG_START_DELAY - SAPS_DELAY;
if(ni>1)
{
if(f1180[A] == 'y') /* Set up f1180 */
tau1 += 0.5*csa/sw1; /* if not PRexp then csa = 1.0 */
if(PRexp)
{
halfT2 = 0.5*(ni-1)/sw1; /* ni2 is not defined */
if(f1180[A] == 'y')
{ tau2 += 0.5*sna/sw1; halfT2 += 0.25*sna/sw1; }
t2b = (double) t1_counter*((halfT2 - CTdelay)/((double)(ni-1)));
}
}
if (ni2>1)
{
halfT2 = 0.5*(ni2-1)/sw2;
if(f2180[A] == 'y') /* Set up f2180 */
{ tau2 += 0.5/sw2; halfT2 += 0.25/sw2; }
t2b = (double) t2_counter*((halfT2 - CTdelay)/((double)(ni2-1)));
}
tau1 = tau1/2.0;
tau2 = tau2/2.0;
if(tau1 < 0.2e-6) tau1 = 0.0;
if(tau2 < 0.2e-6) tau2 = 0.0;
if(t2b < 0.0) t2b = 0.0;
t2a = CTdelay - tau2 + t2b;
if(t2a < 0.2e-6) t2a = 0.0;
/* uncomment these lines to check t2a and t2b
printf("%d: t2a = %.12f", t2_counter,t2a);
printf(" ; t2b = %.12f\n", t2b);
*/
/* BEGIN PULSE SEQUENCE */
status(A);
delay(d1);
if ( dm3[B] == 'y' )
{ lk_hold(); lk_sampling_off();} /*freezes z0 correction, stops lock pulsing*/
rcvroff();
obspower(tpwr);
decpower(pwClvl);
dec2power(pwNlvl);
decpwrf(rf0);
obsoffset(tof);
decoffset(dofCO);
txphase(zero);
delay(1.0e-5);
if (TROSY[A] == 'n')
dec2rgpulse(pwN, zero, 0.0, 0.0); /*destroy N15 and C13 magnetization*/
decrgpulse(pwC, zero, 0.0, 0.0);
zgradpulse(-gzlvl0, 0.5e-3);
delay(1.0e-4);
if (TROSY[A] == 'n')
dec2rgpulse(pwN, one, 0.0, 0.0);
decrgpulse(pwC, zero, 0.0, 0.0);
zgradpulse(-0.7*gzlvl0, 0.5e-3);
delay(5.0e-4);
rgpulse(pw, zero, 0.0, 0.0); /* 1H pulse excitation */
dec2phase(zero);
zgradpulse(gzlvl0, gt0);
delay(lambda - gt0);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
txphase(one);
zgradpulse(gzlvl0, gt0);
delay(lambda - gt0);
rgpulse(pw, one, 0.0, 0.0);
if (tpwrsf < 4095.0)
{obspwrf(tpwrsf);
obspower(tpwrs+6.0);} /* increases tpwrs by 6dB, now need */
else
obspower(tpwrs);
/* tpwrsf to be ~ 2048 for equivalence */
if (TROSY[A]=='y')
{txphase(two);
shaped_pulse("H2Osinc", pwHs, two, 5.0e-4, 0.0);
obspower(tpwr); obspwrf(4095.0);
zgradpulse(gzlvl3, gt3);
delay(2.0e-4);
dec2rgpulse(pwN, zero, 0.0, 0.0);
delay(0.5*kappa - 2.0*pw);
rgpulse(2.0*pw, two, 0.0, 0.0);
obspower(tpwrd); /* POWER_DELAY */
decphase(zero);
dec2phase(zero);
decpwrf(rf8);
delay(timeTN -0.5*kappa - POWER_DELAY - WFG3_START_DELAY);
}
else
{txphase(zero);
if (tpwrsf < 4095.0)
{obspwrf(tpwrsf);
obspower(tpwrs+6.0);} /* increases tpwrs by 6dB, now need */
else
obspower(tpwrs);
/* tpwrsf to be ~ 2048 for equivalence */
shaped_pulse("H2Osinc",pwHs,zero,5.0e-4,0.0);
obspower(tpwrd); obspwrf(4095.0);
zgradpulse(gzlvl3, gt3);
delay(2.0e-4);
dec2rgpulse(pwN, zero, 0.0, 0.0);
txphase(one);
delay(kappa - pwHd - 2.0e-6 - PRG_START_DELAY);
rgpulse(pwHd,one,0.0,0.0);
txphase(zero);
delay(2.0e-6);
obsprgon("waltz16", pwHd, 90.0); /* PRG_START_DELAY */
xmtron();
decphase(zero);
dec2phase(zero);
decpwrf(rf8);
delay(timeTN - kappa - WFG3_START_DELAY);
}
/* WFG3_START_DELAY */
sim3shaped_pulse("", "offC8", "", 0.0, pwC8, 2.0*pwN, zero, zero, zero,
0.0, 0.0);
decphase(zero);
decpwrf(rf6);
delay(timeTN);
dec2rgpulse(pwN, zero, 0.0, 0.0);
if (TROSY[A]=='n')
{xmtroff();
obsprgoff();
rgpulse(pwHd,three,2.0e-6,0.0);}
zgradpulse(-gzlvl3, gt3);
delay(2.0e-4);
decshaped_pulse("offC6", pwC6, zero, 0.0, 0.0);
zgradpulse(-gzlvl7, gt7);
decpwrf(rf0);
decphase(zero);
delay(tauC - gt7 - 0.5*10.933*pwC);
decrgpulse(pwC*158.0/90.0, zero, 0.0, 0.0);
decrgpulse(pwC*171.2/90.0, two, 0.0, 0.0);
decrgpulse(pwC*342.8/90.0, zero, 0.0, 0.0); /* Shaka 6 composite */
decrgpulse(pwC*145.5/90.0, two, 0.0, 0.0);
decrgpulse(pwC*81.2/90.0, zero, 0.0, 0.0);
decrgpulse(pwC*85.3/90.0, two, 0.0, 0.0);
zgradpulse(-gzlvl7, gt7);
decpwrf(rf6);
decphase(one);
txphase(one);
delay(tauC - gt7 - 0.5*10.933*pwC - WFG_START_DELAY);
/* WFG_START_DELAY */
decshaped_pulse("offC6", pwC6, one, 0.0, 0.0);
decoffset(dof);
zgradpulse(-gzlvl9, gt9);
decpwrf(rf1);
decphase(t3);
delay(2.0e-4);
if ( dm3[B] == 'y' ) /* begins optional 2H decoupling */
{
dec3rgpulse(1/dmf3,one,10.0e-6,2.0e-6);
dec3unblank();
dec3phase(zero);
delay(2.0e-6);
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
}
rgpulse(pwHd,one,0.0,0.0);
txphase(zero);
delay(2.0e-6);
obsprgon("waltz16", pwHd, 90.0);
xmtron();
decrgpulse(pwC1, t3, 0.0, 0.0);
decphase(zero);
/* xxxxxxxxxxxxxxxxxxxxxx 13Ca EVOLUTION xxxxxxxxxxxxxxxxxx */
if (ni==1.0) /* special 1D check of pwC9 phase enabled when ni=1 */
{
decpwrf(rf9);
delay(10.0e-6 + SAPS_DELAY + 0.5*pwZ1);
/* WFG3_START_DELAY */
sim3shaped_pulse("", "offC9", "", 0.0, pwC9, 2.0*pwN, zero, zero, zero,
2.0e-6, 0.0);
initval(phshift9, v9);
decstepsize(1.0);
dcplrphase(v9); /* SAPS_DELAY */
delay(10.0e-6 + WFG3_START_DELAY + 0.5*pwZ1);
}
else if(CT_c[A] == 'y') /* xxxxxxx 13Ca Constant Time EVOLUTION xxxxxxxx */
{
decpwrf(rf9);
if(tau1 - 2.0*pwC1/PI - WFG_START_DELAY -POWER_DELAY > 0.0) {
delay(tau1 -2.0*pwC1/PI -POWER_DELAY -WFG_START_DELAY);
sim3shaped_pulse("","offC9","",0.0,pwC8, 2.0*pwN, zero, zero, zero,
0.0, 0.0);
}
else
sim3shaped_pulse("","offC9","",0.0,pwC8, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
delay(timeTC- 2.0e-6 -WFG_STOP_DELAY-POWER_DELAY);
decpwrf(rf2);
decrgpulse(pwC2, zero, 2.0e-6, 2.0e-6); /* 13Ca 180 degree pulse */
delay(timeTC-tau1- 4.0e-6 -SAPS_DELAY);
phshift9 = 230.0; /* = 320-90 - correction for -90 degree phase shift in F1 */
initval(phshift9, v9);
decstepsize(1.0);
dcplrphase(v9); /* SAPS_DELAY */
}
else /* xxxxxxx 13Ca Conventional EVOLUTION xxxxxxxxx */
{
if ((ni>1.0) && (tau1>0.0)) /* total 13C evolution equals d2 exactly */
{ /* 2.0*pwC1/PI compensates for evolution at 64% rate during pwC1 */
decpwrf(rf9);
if(tau1 - 2.0*pwC1/PI - WFG3_START_DELAY - 0.5*pwZ > 0.0)
{
delay(tau1 - 2.0*pwC1/PI - WFG3_START_DELAY - 0.5*pwZ);
sim3shaped_pulse("", "offC9", "", 0.0, pwC8, 2.0*pwN, zero, zero, zero,
0.0, 0.0);
initval(phshift9, v9);
decstepsize(1.0);
dcplrphase(v9); /* SAPS_DELAY */
delay(tau1 - 2.0*pwC1/PI - SAPS_DELAY - 0.5*pwZ - 2.0e-6);
}
else
{
initval(180.0, v9);
decstepsize(1.0);
dcplrphase(v9); /* SAPS_DELAY */
delay(2.0*tau1 - 4.0*pwC1/PI - SAPS_DELAY - 2.0e-6);
}
}
else /* 13Ca evolution refocused for 1st increment */
{
decpwrf(rf2);
delay(10.0e-6);
decrgpulse(pwC2, zero, 2.0e-6, 0.0);
delay(10.0e-6);
}
}
decphase(t5);
decpwrf(rf1);
decrgpulse(pwC1, t5, 2.0e-6, 0.0);
/* xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx */
xmtroff();
obsprgoff();
rgpulse(pwHd,three,2.0e-6,0.0);
decoffset(dofCO);
decpwrf(rf6);
decphase(one);
if ( dm3[B] == 'y' ) /* turns off 2H decoupling */
{
setstatus(DEC3ch, FALSE, 'c', FALSE, dmf3);
dec3rgpulse(1/dmf3,three,2.0e-6,2.0e-6);
dec3blank();
lk_autotrig(); /* resumes lock pulsing */
}
zgradpulse(gzlvl10, gt10);
delay(2.0e-4);
decshaped_pulse("offC6", pwC6, one, 0.0, 0.0);
zgradpulse(gzlvl8, gt7);
decpwrf(rf0);
decphase(zero);
delay(tauC - gt7 - 0.5*10.933*pwC);
decrgpulse(pwC*158.0/90.0, zero, 0.0, 0.0);
decrgpulse(pwC*171.2/90.0, two, 0.0, 0.0);
decrgpulse(pwC*342.8/90.0, zero, 0.0, 0.0); /* Shaka 6 composite */
decrgpulse(pwC*145.5/90.0, two, 0.0, 0.0);
decrgpulse(pwC*81.2/90.0, zero, 0.0, 0.0);
decrgpulse(pwC*85.3/90.0, two, 0.0, 0.0);
zgradpulse(gzlvl8, gt7);
decpwrf(rf6);
decphase(zero);
delay(tauC - gt7 - 0.5*10.933*pwC - WFG_START_DELAY);
/* WFG_START_DELAY */
decshaped_pulse("offC6", pwC6, zero, 0.0, 0.0);
/* xxxxxxxxxxxxxxxxxx OPTIONS FOR N15 EVOLUTION xxxxxxxxxxxxxxxxxxxxx */
zgradpulse(gzlvl4, gt4);
txphase(one);
decphase(zero);
decpwrf(rf8);
dcplrphase(zero);
dec2phase(t8);
delay(2.0e-4);
if (TROSY[A]=='n')
{rgpulse(pwHd,one,0.0,0.0);
txphase(zero);
delay(2.0e-6);
obsprgon("waltz16", pwHd, 90.0);
xmtron();}
dec2rgpulse(pwN, t8, 0.0, 0.0); /* N15 EVOLUTION BEGINS HERE */
dec2phase(t9);
if(SCT[A] == 'y')
{
delay(t2a);
dec2rgpulse(2.0*pwN, t9, 0.0, 0.0);
delay(t2b);
decshaped_pulse("offC8", pwC8, zero, 0.0, 0.0); /* WFG_START_DELAY */
}
else
{
delay(timeTN - WFG3_START_DELAY - tau2); /* WFG3_START_DELAY */
sim3shaped_pulse("", "offC8", "", 0.0, pwC8, 2.0*pwN, zero, zero, t9,
0.0, 0.0);
}
dec2phase(t10);
decpwrf(rf3);
if (TROSY[A]=='y')
{ if (tau2 > gt1 + 2.0*GRADIENT_DELAY + 1.5e-4 + pwHs)
{
txphase(three);
delay(timeTN - pwC3 - WFG_START_DELAY); /* WFG_START_DELAY */
decshaped_pulse("offC3", pwC3, zero, 0.0, 0.0);
delay(tau2 - gt1 - 2.0*GRADIENT_DELAY - 1.5e-4 - pwHs);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspower(tpwrs); /* POWER_DELAY */
delay(1.0e-4 - POWER_DELAY);
if (tpwrsf < 4095.0)
{obspwrf(tpwrsf);
obspower(tpwrs+6.0);} /* increases tpwrs by 6dB, now need */
else
obspower(tpwrs);
/* tpwrsf to be ~ 2048 for equivalence */
shaped_pulse("H2Osinc", pwHs, three, 0.0, 0.0);
obspower(tpwr); obspwrf(4095.0);
txphase(t4);
delay(0.5e-4 - POWER_DELAY);
}
else if (tau2 > pwHs + 0.5e-4)
{
txphase(three);
delay(timeTN-pwC3-WFG_START_DELAY-gt1-2.0*GRADIENT_DELAY-1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspower(tpwrs); /* POWER_DELAY */
delay(1.0e-4 - POWER_DELAY); /* WFG_START_DELAY */
decshaped_pulse("offC3", pwC3, zero, 0.0, 0.0);
delay(tau2 - pwHs - 0.5e-4);
if (tpwrsf < 4095.0)
{obspwrf(tpwrsf);
obspower(tpwrs+6.0);} /* increases tpwrs by 6dB, now need */
else
obspower(tpwrs);
/* tpwrsf to be ~ 2048 for equivalence */
shaped_pulse("H2Osinc", pwHs, three, 0.0, 0.0);
obspower(tpwr); obspwrf(4095.0);
txphase(t4);
delay(0.5e-4 - POWER_DELAY);
}
else
{
txphase(three);
delay(timeTN - pwC3 - WFG_START_DELAY - gt1 - 2.0*GRADIENT_DELAY
- 1.5e-4 - pwHs);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspower(tpwrs); /* POWER_DELAY */
delay(1.0e-4 - POWER_DELAY); /* WFG_START_DELAY */
if (tpwrsf < 4095.0)
{obspwrf(tpwrsf);
obspower(tpwrs+6.0);} /* increases tpwrs by 6dB, now need */
else
obspower(tpwrs);
/* tpwrsf to be ~ 2048 for equivalence */
shaped_pulse("H2Osinc", pwHs, three, 0.0, 0.0);
obspower(tpwr); obspwrf(4095.0);
txphase(t4);
delay(0.5e-4 - POWER_DELAY);
decshaped_pulse("offC3", pwC3, zero, 0.0, 0.0);
delay(tau2);
}
}
else
{
if (tau2 > kappa)
{
delay(timeTN - pwC3 - WFG_START_DELAY); /* WFG_START_DELAY */
decshaped_pulse("offC3", pwC3, zero, 0.0, 0.0);
delay(tau2 - kappa - PRG_STOP_DELAY - pwHd - 2.0e-6);
xmtroff();
obsprgoff(); /* PRG_STOP_DELAY */
rgpulse(pwHd,three,2.0e-6,0.0);
txphase(t4);
delay(kappa - gt1 - 2.0*GRADIENT_DELAY - 1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspower(tpwr); /* POWER_DELAY */
delay(1.0e-4 - POWER_DELAY);
}
else if (tau2 > (kappa - pwC3 - WFG_START_DELAY))
{
delay(timeTN + tau2 - kappa - PRG_STOP_DELAY - pwHd - 2.0e-6);
xmtroff();
obsprgoff(); /* PRG_STOP_DELAY */
rgpulse(pwHd,three,2.0e-6,0.0);
txphase(t4); /* WFG_START_DELAY */
decshaped_pulse("offC3", pwC3, zero, 0.0, 0.0);
delay(kappa -pwC3 -WFG_START_DELAY -gt1 -2.0*GRADIENT_DELAY -1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspower(tpwr); /* POWER_DELAY */
delay(1.0e-4 - POWER_DELAY);
}
else if (tau2 > gt1 + 2.0*GRADIENT_DELAY + 1.0e-4)
{
delay(timeTN + tau2 - kappa - PRG_STOP_DELAY - pwHd - 2.0e-6);
xmtroff();
obsprgoff(); /* PRG_STOP_DELAY */
rgpulse(pwHd,three,2.0e-6,0.0);
txphase(t4);
delay(kappa - tau2 - pwC3 - WFG_START_DELAY); /* WFG_START_DELAY */
decshaped_pulse("offC3", pwC3, zero, 0.0, 0.0);
delay(tau2 - gt1 - 2.0*GRADIENT_DELAY - 1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspower(tpwr); /* POWER_DELAY */
delay(1.0e-4 - POWER_DELAY);
}
else
{
delay(timeTN + tau2 - kappa - PRG_STOP_DELAY - pwHd - 2.0e-6);
xmtroff();
obsprgoff(); /* PRG_STOP_DELAY */
rgpulse(pwHd,three,2.0e-6,0.0);
txphase(t4);
delay(kappa-tau2-pwC3-WFG_START_DELAY-gt1-2.0*GRADIENT_DELAY-1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspower(tpwr); /* POWER_DELAY */
delay(1.0e-4 - POWER_DELAY); /* WFG_START_DELAY */
decshaped_pulse("offC3", pwC3, zero, 0.0, 0.0);
delay(tau2);
}
}
/* xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx */
if (TROSY[A]=='y') rgpulse(pw, t4, 0.0, 0.0);
else sim3pulse(pw, 0.0, pwN, t4, zero, t10, 0.0, 0.0);
txphase(zero);
dec2phase(zero);
zgradpulse(gzlvl5, gt5);
if (TROSY[A]=='y') delay(lambda - 0.65*(pw + pwN) - gt5);
else delay(lambda - 1.3*pwN - gt5);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl5, gt5);
txphase(one);
dec2phase(t11);
delay(lambda - 1.3*pwN - gt5);
sim3pulse(pw, 0.0, pwN, one, zero, t11, 0.0, 0.0);
txphase(zero);
dec2phase(zero);
zgradpulse(gzlvl6, gt5);
delay(lambda - 1.3*pwN - gt5);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
dec2phase(t10);
zgradpulse(gzlvl6, gt5);
if (TROSY[A]=='y') delay(lambda - 1.6*pwN - gt5);
else delay(lambda - 0.65*pwN - gt5);
if (TROSY[A]=='y') dec2rgpulse(pwN, t10, 0.0, 0.0);
else rgpulse(pw, zero, 0.0, 0.0);
delay((gt1/10.0) + 1.0e-4 +gstab - 0.5*pw + 2.0*GRADIENT_DELAY + POWER_DELAY);
rgpulse(2.0*pw, zero, 0.0,rof1);
dec2power(dpwr2); /* POWER_DELAY */
if (mag_flg[A] == 'y') magradpulse(icosel*gzcal*gzlvl2, gt1/10.0);
else zgradpulse(icosel*gzlvl2, gt1/10.0); /* 2.0*GRADIENT_DELAY */
delay(gstab);
rcvron();
statusdelay(C,1.0e-4 - rof1);
if (dm3[B]=='y') lk_sample();
setreceiver(t12);
}
pulsesequence()
{
/* DECLARE AND LOAD VARIABLES */
char f1180[MAXSTR], /* Flag to start t1 @ halfdwell */
f2180[MAXSTR], /* Flag to start t2 @ halfdwell */
rna_stCdec[MAXSTR], /* calls STUD+ waveforms from shapelib */
STUD[MAXSTR]; /* apply automatically calculated STUD decoupling */
int icosel1, /* used to get n and p type */
icosel2,
t1_counter, /* used for states tppi in t1 */
t2_counter, /* used for states tppi in t2 */
ni2 = getval("ni2");
double tau1, /* t1 delay */
tau2, /* t2 delay */
del = getval("del"), /* time delays for CH coupling evolution */
del1 = getval("del1"),
del2 = getval("del2"),
/* STUD+ waveforms automatically calculated by macro "rnacal" */
/* and string parameter rna_stCdec calls them from your shapelib.*/
stdmf, /* dmf for STUD decoupling */
studlvl, /* coarse power for STUD+ decoupling */
rf80 = getval("rf80"), /* rf in Hz for 80ppm STUD+ */
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
rfC, /* maximum fine power when using pwC pulses */
dofa, /* dof shifted to 80 ppm for ribose */
/* p_d is used to calculate the isotropic mixing on the Cab region */
p_d, /* 50 degree pulse for DIPSI-3 at rfd */
rfd, /* fine power for 35 ppm */
ncyc = getval("ncyc"), /* no. of cycles of DIPSI-3 */
compC = getval("compC"), /* adjustment for C13 amplifier compression */
pwNlvl = getval("pwNlvl"), /* power for N15 pulses */
pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */
sw1 = getval("sw1"),
sw2 = getval("sw2"),
grecov = getval("grecov"), /* Gradient recovery delay, typically 150-200us */
gt1 = getval("gt1"), /* coherence pathway gradients */
gzlvl1 = getval("gzlvl1"),
gzlvl2 = getval("gzlvl2"),
gt3 = getval("gt3"), /* other gradients */
gt5 = getval("gt5"),
gzlvl3 = getval("gzlvl3"),
gzlvl4 = getval("gzlvl4"),
gzlvl5 = getval("gzlvl5"),
gzlvl6 = getval("gzlvl6");
getstr("STUD",STUD);
getstr("f1180",f1180);
getstr("f2180",f2180);
/* LOAD PHASE TABLE */
settable(t3,2,phi3);
settable(t6,1,phi6);
settable(t5,4,phi5);
settable(t10,1,phi10);
settable(t11,4,rec);
/* INITIALIZE VARIABLES */
if( dpwrf < 4095 )
{ text_error("reset dpwrf=4095 and recalibrate C13 90 degree pulse");
psg_abort(1); }
/* maximum fine power for pwC pulses */
rfC = 4095.0;
/* Center dof in RIBOSE region on 80 ppm. */
dofa = dof - 30.0*dfrq;
/* dipsi-3 decoupling C-ribose */
p_d = (5.0)/(9.0*4.0*7000.0*(sfrq/800.0)); /* DIPSI-3 covers 35 ppm */
rfd = (compC*4095.0*pwC*5.0)/(p_d*9.0);
rfd = (int) (rfd + 0.5);
ncyc = (int) (ncyc + 0.5);
/* 80 ppm STUD+ decoupling */
strcpy(rna_stCdec, "wurst80");
stdmf = getval("dmf80");
studlvl = pwClvl + 20.0*log10(compC*pwC*4.0*rf80);
studlvl = (int) (studlvl + 0.5);
/* CHECK VALIDITY OF PARAMETER RANGES */
if( gt1 > 0.5*del - 0.5*grecov )
{ text_error(" gt1 is too big. Make gt1 less than %f.\n", (0.5*del - 0.5*grecov)); psg_abort(1);}
if((dm3[A] == 'y' || dm3[C] == 'y' ))
{ text_error("incorrect dec1 decoupler flags! Should be 'nyn' or 'nnn' "); psg_abort(1); }
if((dm2[A] == 'y' || dm2[B] == 'y'))
{ text_error("incorrect dec2 decoupler flags! Should be 'nnn' or 'nny' "); psg_abort(1); }
if((dm[A] == 'y' || dm[B] == 'y'))
{ text_error("incorrect dec1 decoupler flags! Should be 'nny' "); psg_abort(1); }
if( (((dm[C] == 'y') && (dm2[C] == 'y')) && (STUD[A] == 'y')) )
{ text_error("incorrect dec2 decoupler flags! Should be 'nnn' if STUD='y'"); psg_abort(1); }
if( dpwr > 50 )
{ text_error("don't fry the probe, DPWR too large! "); psg_abort(1); }
if( dpwr2 > 50 )
{ text_error("don't fry the probe, DPWR2 too large! "); psg_abort(1); }
if( (pw > 20.0e-6) && (tpwr > 56) )
{ text_error("don't fry the probe, pw too high ! "); psg_abort(1); }
if( (pwC > 40.0e-6) && (pwClvl > 56) )
{ text_error("don't fry the probe, pwN too high ! "); psg_abort(1); }
if( (pwN > 100.0e-6) && (pwNlvl > 56) )
{ text_error("don't fry the probe, pwN too high ! "); psg_abort(1); }
if ((dm3[B] == 'y' && dpwr3 > 44 ))
{ text_error ("Deuterium decoupling power too high ! "); psg_abort(1); }
if ((ncyc > 1 ) && (ix == 1))
{ text_error("mixing time is %f ms.\n",(ncyc*97.8*4*p_d)); }
/* PHASES AND INCREMENTED TIMES */
/* Phase incrementation for hypercomplex 2D data, States-Haberkorn element */
icosel1 = -1; icosel2 = -1;
if (phase1 == 2)
{ tsadd(t6,2,4); icosel1 = -1*icosel1; }
if (phase2 == 2)
{ tsadd(t10,2,4); icosel2 = -1*icosel2; tsadd(t6,2,4); }
/* Set up f1180 */
tau1 = d2;
if((f1180[A] == 'y') && (ni > 1.0))
{ tau1 += ( 1.0 / (2.0*sw1) ); if(tau1 < 0.2e-6) tau1 = 0.0; }
tau1 = tau1/2.0;
/* Set up f2180 */
tau2 = d3;
if((f2180[A] == 'y') && (ni2 > 1.0))
{ tau2 += ( 1.0 / (2.0*sw2) ); if(tau2 < 0.2e-6) tau2 = 0.0; }
tau2 = tau2/2.0;
/* Calculate modifications to phases for States-TPPI acquisition */
if( ix == 1) d2_init = d2;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if(t1_counter % 2)
{ tsadd(t3,2,4); tsadd(t11,2,4); }
if( ix == 1) d3_init = d3;
t2_counter = (int) ( (d3-d3_init)*sw2 + 0.5 );
if(t2_counter % 2)
{ tsadd(t5,2,4); tsadd(t11,2,4); }
/* BEGIN PULSE SEQUENCE */
status(A);
if (dm3[B]=='y') lk_sample();
delay(d1);
if (dm3[B]=='y') lk_hold();
rcvroff();
obspower(tpwr);
decpower(pwClvl);
dec2power(pwNlvl);
decpwrf(rfC);
obsoffset(tof);
decoffset(dofa);
dec2offset(dof2);
txphase(t3);
delay(1.0e-5);
decrgpulse(pwC, zero, 0.0, 0.0); /*destroy C13 magnetization*/
zgradpulse(gzlvl1, 0.5e-3);
delay(grecov/2);
decrgpulse(pwC, one, 0.0, 0.0);
zgradpulse(0.7*gzlvl1, 0.5e-3);
delay(5.0e-4);
if(dm3[B] == 'y') /*optional 2H decoupling on */
{
dec3unblank();
dec3rgpulse(1/dmf3, one, 0.0, 0.0);
dec3unblank();
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
}
rgpulse(pw, t3, 0.0, 0.0); /* 1H pulse excitation */
decphase(zero);
delay(0.5*del + tau1 - 2.0*pwC);
decrgpulse(2.0*pwC, zero, 0.0, 0.0);
txphase(zero);
delay(tau1);
rgpulse(2.0*pw, zero, 0.0, 0.0);
zgradpulse(icosel1*gzlvl1, 0.1*gt1);
decphase(t5);
delay(0.5*del - 0.1*gt1);
simpulse(pw, pwC, zero, t5, 0.0, 0.0);
zgradpulse(gzlvl3, gt3);
decphase(zero);
delay(0.5*del2 - gt3);
simpulse(2.0*pw, 2.0*pwC, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl3, gt3);
txphase(t6);
decphase(one);
delay(0.5*del2 - gt3);
simpulse(pw, pwC, t6, one, 0.0, 0.0);
zgradpulse(gzlvl4, gt3);
txphase(zero);
decphase(zero);
delay(0.5*del1 - gt3);
simpulse(2.0*pw, 2.0*pwC, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl4, gt3);
delay(0.5*del1 - gt3);
decrgpulse(pwC, zero, 0.0, 0.0);
decpwrf(rfd);
delay(2.0e-6);
initval(ncyc, v2);
starthardloop(v2);
decrgpulse(4.9*p_d,zero,0.0,0.0);
decrgpulse(7.9*p_d,two,0.0,0.0);
decrgpulse(5.0*p_d,zero,0.0,0.0);
decrgpulse(5.5*p_d,two,0.0,0.0);
decrgpulse(0.6*p_d,zero,0.0,0.0);
decrgpulse(4.6*p_d,two,0.0,0.0);
decrgpulse(7.2*p_d,zero,0.0,0.0);
decrgpulse(4.9*p_d,two,0.0,0.0);
decrgpulse(7.4*p_d,zero,0.0,0.0);
decrgpulse(6.8*p_d,two,0.0,0.0);
decrgpulse(7.0*p_d,zero,0.0,0.0);
decrgpulse(5.2*p_d,two,0.0,0.0);
decrgpulse(5.4*p_d,zero,0.0,0.0);
decrgpulse(0.6*p_d,two,0.0,0.0);
decrgpulse(4.5*p_d,zero,0.0,0.0);
decrgpulse(7.3*p_d,two,0.0,0.0);
decrgpulse(5.1*p_d,zero,0.0,0.0);
decrgpulse(7.9*p_d,two,0.0,0.0);
decrgpulse(4.9*p_d,two,0.0,0.0);
decrgpulse(7.9*p_d,zero,0.0,0.0);
decrgpulse(5.0*p_d,two,0.0,0.0);
decrgpulse(5.5*p_d,zero,0.0,0.0);
decrgpulse(0.6*p_d,two,0.0,0.0);
decrgpulse(4.6*p_d,zero,0.0,0.0);
decrgpulse(7.2*p_d,two,0.0,0.0);
decrgpulse(4.9*p_d,zero,0.0,0.0);
decrgpulse(7.4*p_d,two,0.0,0.0);
decrgpulse(6.8*p_d,zero,0.0,0.0);
decrgpulse(7.0*p_d,two,0.0,0.0);
decrgpulse(5.2*p_d,zero,0.0,0.0);
decrgpulse(5.4*p_d,two,0.0,0.0);
decrgpulse(0.6*p_d,zero,0.0,0.0);
decrgpulse(4.5*p_d,two,0.0,0.0);
decrgpulse(7.3*p_d,zero,0.0,0.0);
decrgpulse(5.1*p_d,two,0.0,0.0);
decrgpulse(7.9*p_d,zero,0.0,0.0);
decrgpulse(4.9*p_d,two,0.0,0.0);
decrgpulse(7.9*p_d,zero,0.0,0.0);
decrgpulse(5.0*p_d,two,0.0,0.0);
decrgpulse(5.5*p_d,zero,0.0,0.0);
decrgpulse(0.6*p_d,two,0.0,0.0);
decrgpulse(4.6*p_d,zero,0.0,0.0);
decrgpulse(7.2*p_d,two,0.0,0.0);
decrgpulse(4.9*p_d,zero,0.0,0.0);
decrgpulse(7.4*p_d,two,0.0,0.0);
decrgpulse(6.8*p_d,zero,0.0,0.0);
decrgpulse(7.0*p_d,two,0.0,0.0);
decrgpulse(5.2*p_d,zero,0.0,0.0);
decrgpulse(5.4*p_d,two,0.0,0.0);
decrgpulse(0.6*p_d,zero,0.0,0.0);
decrgpulse(4.5*p_d,two,0.0,0.0);
decrgpulse(7.3*p_d,zero,0.0,0.0);
decrgpulse(5.1*p_d,two,0.0,0.0);
decrgpulse(7.9*p_d,zero,0.0,0.0);
decrgpulse(4.9*p_d,zero,0.0,0.0);
decrgpulse(7.9*p_d,two,0.0,0.0);
decrgpulse(5.0*p_d,zero,0.0,0.0);
decrgpulse(5.5*p_d,two,0.0,0.0);
decrgpulse(0.6*p_d,zero,0.0,0.0);
decrgpulse(4.6*p_d,two,0.0,0.0);
decrgpulse(7.2*p_d,zero,0.0,0.0);
decrgpulse(4.9*p_d,two,0.0,0.0);
decrgpulse(7.4*p_d,zero,0.0,0.0);
decrgpulse(6.8*p_d,two,0.0,0.0);
decrgpulse(7.0*p_d,zero,0.0,0.0);
decrgpulse(5.2*p_d,two,0.0,0.0);
decrgpulse(5.4*p_d,zero,0.0,0.0);
decrgpulse(0.6*p_d,two,0.0,0.0);
decrgpulse(4.5*p_d,zero,0.0,0.0);
decrgpulse(7.3*p_d,two,0.0,0.0);
decrgpulse(5.1*p_d,zero,0.0,0.0);
decrgpulse(7.9*p_d,two,0.0,0.0);
endhardloop();
dec2phase(zero);
decphase(zero);
txphase(zero);
decpwrf(rfC);
delay(tau2);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
delay(tau2);
decpwrf(rfC);
zgradpulse(-icosel2*gzlvl2, 1.8*gt1);
delay(grecov+2.0e-6);
decrgpulse(2.0*pwC, zero, 0.0, 0.0);
decpwrf(rfC);
zgradpulse(icosel2*gzlvl2, 1.8*gt1);
delay(grecov + pwN);
decrgpulse(pwC, zero, 0.0, 0.0);
decpwrf(rfC);
decrgpulse(pwC, zero, 2.0e-6, 0.0);
zgradpulse(gzlvl5, gt5);
delay(0.5*del1 - gt5);
simpulse(2.0*pw, 2.0*pwC, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl5, gt5);
txphase(one);
decphase(t10);
delay(0.5*del1 - gt5);
simpulse(pw, pwC, one, t10, 0.0, 0.0);
zgradpulse(gzlvl6, gt5);
txphase(zero);
decphase(zero);
delay(0.5*del2 - gt5);
simpulse(2.0*pw, 2.0*pwC, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl6, gt5);
delay(0.5*del2 - gt5);
simpulse(pw, pwC, zero, zero, 0.0, 0.0);
delay(0.5*del - 0.5*pwC);
simpulse(2.0*pw,2.0*pwC, zero, zero, 0.0, 0.0);
if (STUD[A]=='y') decpower(studlvl);
else
{
decpower(dpwr);
dec2power(dpwr2);
}
zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
if(dm3[B] == 'y')
delay(0.5*del - gt1 -1/dmf3 - 2.0*GRADIENT_DELAY - POWER_DELAY);
else
delay(0.5*del - gt1 - 2.0*GRADIENT_DELAY - POWER_DELAY);
if(dm3[B] == 'y') /*optional 2H decoupling off */
{
dec3rgpulse(1/dmf3, three, 0.0, 0.0); dec3blank();
setstatus(DEC3ch, FALSE, 'w', FALSE, dmf3);
dec3blank();
}
decpower(dpwr); /* POWER_DELAY */
if (dm3[B]=='y') lk_sample();
if ((STUD[A]=='y') && (dm[C] == 'y'))
{decpower(studlvl);
decunblank();
decon();
decprgon(rna_stCdec,1/stdmf, 1.0);
startacq(alfa);
acquire(np, 1.0/sw);
decprgoff();
decoff();
decblank();
}
else
status(C);
setreceiver(t11);
}
pulsesequence()
{
/* DECLARE AND LOAD VARIABLES */
char f1180[MAXSTR], /* Flag to start t1 @ halfdwell */
f2180[MAXSTR], /* Flag to start t2 @ halfdwell */
H2Opurge[MAXSTR], stCdec[MAXSTR], /* calls STUD+ waveforms from shapelib */
STUD[MAXSTR]; /* apply automatically calculated STUD decoupling */
int t1_counter, /* used for states tppi in t1 */
t2_counter; /* used for states tppi in t2 */
double tau1, /* t1 delay */
BPdpwrspinlock, /* user-defined upper limit for spinlock(Hz) */
BPpwrlimits, /* =0 for no limit, =1 for limit */
tau2, /* t2 delay */
ni = getval("ni"), ni2 = getval("ni2"),
stdmf = getval("dmf80"), /* dmf for 80 ppm of STUD decoupling */
rf80 = getval("rf80"), /* rf in Hz for 80ppm STUD+ */
taua = getval("taua"), /* time delays for CH coupling evolution */
taub = getval("taub"), tauc = getval("tauc"),
/* string parameter stCdec calls stud decoupling waveform from your shapelib. */
studlvl, /* coarse power for STUD+ decoupling */
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
rf0, /* maximum fine power when using pwC pulses */
/* p_d is used to calculate the isotropic mixing on the Cab region */
p_d, /* 50 degree pulse for DIPSI-3 at rfd */
rfd, /* fine power for 9.0 kHz rf at 600MHz */
ncyc = getval("ncyc"), /* no. of cycles of DIPSI-3 */
spinlock = getval("spinlock"), /* DIPSI-3 Field Strength in Hz */
/* the following pulse length for the SLP pulse is automatically calculated */
/* by the macro "hcch_tocsy". The SLP pulse shape,"offC10" is called */
/* directly from your shapelib. */
pwC10 = getval("pwC10"), /* 180 degree selective sinc pulse on CO(174ppm) */
rf7, /* fine power for the pwC10 ("offC10") pulse */
compC = getval("compC"), /* adjustment for C13 amplifier compression */
pwNlvl = getval("pwNlvl"), /* power for N15 pulses */
pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */
sw1 = getval("sw1"), sw2 = getval("sw2"),
gt0 = getval("gt0"), /* other gradients */
gt3 = getval("gt3"), gt4 = getval("gt4"), gt5 = getval("gt5"),
gt7 = getval("gt7"), gzlvl0 = getval("gzlvl0"), gzlvl3 = getval("gzlvl3"),
gzlvl4 = getval("gzlvl4"), gzlvl5 = getval("gzlvl5"), gzlvl6 = getval("gzlvl6"),
gzlvl7 = getval("gzlvl7");
getstr("f1180", f1180);
getstr("f2180", f2180);
getstr("H2Opurge", H2Opurge);
getstr("STUD", STUD);
/* 80 ppm STUD+ decoupling */
strcpy(stCdec, "stCdec80");
studlvl = pwClvl + 20.0 * log10(compC * pwC * 4.0 * rf80);
studlvl = (int) (studlvl + 0.5);
P_getreal(GLOBAL,"BPpwrlimits",&BPpwrlimits,1);
P_getreal(GLOBAL,"BPdpwrspinlock",&BPdpwrspinlock,1);
/* LOAD PHASE TABLE */
settable(t3, 2, phi3);
settable(t5, 4, phi5);
settable(t9, 8, phi9);
settable(t11, 8, rec);
/* INITIALIZE VARIABLES */
if (BPpwrlimits > 0.5)
{
if (spinlock > BPdpwrspinlock)
{
spinlock = BPdpwrspinlock;
printf("spinlock too large, reset to user-defined limit (BPdpwrspinlock)");
psg_abort(1);
}
}
if (dpwrf < 4095)
{
printf("reset dpwrf=4095 and recalibrate C13 90 degree pulse");
psg_abort(1);
}
if ((pwC > (25.0e-6 * 600.0 / sfrq)) && (ncyc > 0.0))
{
printf("Increase pwClvl so that pwC < 25*600/sfrq");
psg_abort(1);
}
/* maximum fine power for pwC pulses */
rf0 = 4095.0;
/* 180 degree one-lobe sinc pulse on CO, null at Ca 139ppm away */
rf7 = (compC * 4095.0 * pwC * 2.0 * 1.65) / pwC10; /* needs 1.65 times more */
rf7 = (int) (rf7 + 0.5); /* power than a square pulse */
if (spinlock < 1000.0)
{
printf("Spinlock seems too low. Please check spinlock value ! ");
psg_abort(1);
}
/* dipsi-3 spinlock on CbCa */
p_d = (5.0) / (9.0 * 4.0 * spinlock); /* DIPSI-3 */
rfd = (compC * 4095.0 * pwC * 5.0) / (p_d * 9.0);
rfd = (int) (rfd + 0.5);
ncyc = (int) (ncyc + 0.5);
/*************************For Ultra-High Field Probes***************************/
if (sfrq>590.0)
{
if (ncyc>2)
{
if (pwC>15)
{
if (rfd > 2000)
{
printf("spinlock too large. Lower value for probe protection");
psg_abort(1);
}
}
else
{
if (pwC>14)
{
if (rfd > 1800)
{
printf("spinlock too large. Lower value for probe protection");
psg_abort(1);
}
}
else
{
if (pwC>13)
{
if (rfd > 1600)
{
printf("spinlock too large. Lower value for probe protection");
psg_abort(1);
}
}
else
{
if (pwC>12)
{
if (rfd > 1400)
{
printf("spinlock too large. Lower value for probe protection");
psg_abort(1);
}
}
else
{
if (pwC>11)
{
if (rfd > 1200)
{
printf("spinlock too large. Lower value for probe protection");
psg_abort(1);
}
}
else
{
if (rfd > 1000)
{
printf("spinlock too large. Lower value for probe protection");
psg_abort(1);
}
}
}
}
}
}
}
else
{
if (ncyc == 2)
{
if (pwC>15)
{
if (rfd > 2200)
{
printf("spinlock too large. Lower value for probe protection");
psg_abort(1);
}
}
else
{
if (pwC>14)
{
if (rfd > 2000)
{
printf("spinlock too large. Lower value for probe protection");
psg_abort(1);
}
}
else
{
if (pwC>13)
{
if (rfd > 1800)
{
printf("spinlock too large. Lower value for probe protection");
psg_abort(1);
}
}
else
{
if (pwC>12)
{
if (rfd > 1600)
{
printf("spinlock too large. Lower value for probe protection");
psg_abort(1);
}
}
else
{
if (pwC>11)
{
if (rfd > 1400)
{
printf("spinlock too large. Lower value for probe protection");
psg_abort(1);
}
}
else
{
if (rfd > 1200)
{
printf("spinlock too large. Lower value for probe protection");
psg_abort(1);
}
}
}
}
}
}
}
else
{
if (ncyc == 1)
{
if (pwC>15)
{
if (rfd > 2400)
{
printf("spinlock too large. Lower value for probe protection");
psg_abort(1);
}
}
else
{
if (pwC>14)
{
if (rfd > 2200)
{
printf("spinlock too large. Lower value for probe protection");
psg_abort(1);
}
}
else
{
if (pwC>13)
{
if (rfd > 2000)
{
printf("spinlock too large. Lower value for probe protection");
psg_abort(1);
}
}
else
{
if (pwC>12)
{
if (rfd > 1800)
{
printf("spinlock too large. Lower value for probe protection");
psg_abort(1);
}
}
else
{
if (pwC>11)
{
if (rfd > 1600)
{
printf("spinlock too large. Lower value for probe protection");
psg_abort(1);
}
}
else
{
if (rfd > 1400)
{
printf("spinlock too large. Lower value for probe protection");
psg_abort(1);
}
}
}
}
}
}
}
}
}
}
/*********************End: For Ultra-High Field Probes***************************/
/* CHECK VALIDITY OF PARAMETER RANGES */
if ((dm[A] == 'y' || dm[B] == 'y'))
{
printf("incorrect dec1 decoupler flags! Should be 'nny' or 'nnn' ");
psg_abort(1);
}
if ((dm2[A] == 'y' || dm2[B] == 'y' || dm2[C] == 'y'))
{
printf("incorrect dec2 decoupler flags! Should be 'nnn' ");
psg_abort(1);
}
if ((dm3[A] == 'y' || dm3[C] == 'y'))
{
printf("incorrect dec1 decoupler flags! Should be 'nyn' or 'nnn' ");
psg_abort(1);
}
if (dpwr > 52)
{
printf("don't fry the probe, DPWR too large! ");
psg_abort(1);
}
if (pw > 80.0e-6)
{
printf("dont fry the probe, pw too high ! ");
psg_abort(1);
}
if (pwN > 100.0e-6)
{
printf("dont fry the probe, pwN too high ! ");
psg_abort(1);
}
/* PHASES AND INCREMENTED TIMES */
/* Phase incrementation for hypercomplex 2D data, States-Haberkorn element */
if (phase1 == 2)
tsadd(t3, 1, 4);
if (phase2 == 2)
tsadd(t5, 1, 4);
/* C13 TIME INCREMENTATION and set up f1180 */
/* Set up f1180 */
tau1 = d2;
if (f1180[A] == 'y')
{
tau1 += (1.0 / (2.0 * sw1));
if (tau1 < 0.2e-6)
tau1 = 0.0;
}
tau1 = tau1 / 2.0;
/* Set up f2180 */
tau2 = d3;
if (f2180[A] == 'y')
{
tau2 += (1.0 / (2.0 * sw2));
if (tau2 < 0.2e-6)
tau2 = 0.0;
}
tau2 = tau2 / 2.0;
/* Calculate modifications to phases for States-TPPI acquisition */
if (ix == 1)
d2_init = d2;
t1_counter = (int) ((d2 - d2_init) * sw1 + 0.5);
if (t1_counter % 2)
{
tsadd(t3, 2, 4);
tsadd(t11, 2, 4);
}
if (ix == 1)
d3_init = d3;
t2_counter = (int) ((d3 - d3_init) * sw2 + 0.5);
if (t2_counter % 2)
{
tsadd(t5, 2, 4);
tsadd(t11, 2, 4);
}
/* BEGIN PULSE SEQUENCE */
status(A);
if (dm3[B] == 'y')
lk_sample();
if ((ni / sw1 - d2) > 0)
delay(ni / sw1 - d2); /*decreases as t1 increases for const.heating */
if ((ni2 / sw2 - d3) > 0)
delay(ni2 / sw2 - d3); /*decreases as t2 increases for const.heating */
delay(d1);
if (dm3[B] == 'y')
{
lk_hold();
lk_sampling_off();
} /*freezes z0 correction, stops lock pulsing */
rcvroff();
obspower(tpwr);
decpower(pwClvl);
dec2power(pwNlvl);
decpwrf(rf0);
obsoffset(tof);
txphase(t3);
delay(1.0e-5);
decrgpulse(pwC, zero, 0.0, 0.0); /*destroy C13 magnetization */
zgradpulse(gzlvl0, 0.5e-3);
delay(1.0e-4);
decrgpulse(pwC, one, 0.0, 0.0);
zgradpulse(0.7 * gzlvl0, 0.5e-3);
delay(5.0e-4);
if (dm3[B] == 'y') /* begins optional 2H decoupling */
{
dec3rgpulse(1 / dmf3, one, 10.0e-6, 2.0e-6);
dec3unblank();
dec3phase(zero);
delay(2.0e-6);
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
}
rgpulse(pw, t3, 0.0, 0.0); /* 1H pulse excitation */
zgradpulse(gzlvl0, gt0); /* 2.0*GRADIENT_DELAY */
decphase(zero);
delay(taua + tau1 - gt0 - 2.0 * GRADIENT_DELAY - 2.0 * pwC);
decrgpulse(2.0 * pwC, zero, 0.0, 0.0);
txphase(zero);
delay(tau1);
rgpulse(2.0 * pw, zero, 0.0, 0.0);
zgradpulse(gzlvl0, gt0);
txphase(one);
decphase(t5);
delay(taua - gt0);
rgpulse(pw, one, 0.0, 0.0);
zgradpulse(gzlvl3, gt3);
delay(2.0e-4);
decrgpulse(pwC, t5, 0.0, 0.0);
delay(tau2);
dec2rgpulse(2.0 * pwN, zero, 0.0, 0.0);
zgradpulse(gzlvl4, gt4); /* 2.0*GRADIENT_DELAY */
decphase(zero);
decpwrf(rf7);
delay(taub - 2.0 * pwN - gt4 - 2.0 * GRADIENT_DELAY);
decshaped_pulse("offC10", pwC10, zero, 0.0, 0.0);
txphase(zero);
decpwrf(rf0);
delay(taub - 2.0 * pw);
rgpulse(2.0 * pw, zero, 0.0, 0.0);
delay(tau2);
decrgpulse(2.0 * pwC, zero, 0.0, 0.0);
decpwrf(rf7);
delay(taub);
decshaped_pulse("offC10", pwC10, zero, 0.0, 0.0);
zgradpulse(gzlvl4, gt4); /* 2.0*GRADIENT_DELAY */
delay(taub - gt4 - 2.0 * GRADIENT_DELAY);
decpwrf(rfd);
decrgpulse(1.0e-3, zero, 0.0, 0.0);
if (ncyc>0)
{
initval(ncyc, v2);
starthardloop(v2);
decrgpulse(4.9 * p_d, one, 0.0, 0.0);
decrgpulse(7.9 * p_d, three, 0.0, 0.0);
decrgpulse(5.0 * p_d, one, 0.0, 0.0);
decrgpulse(5.5 * p_d, three, 0.0, 0.0);
decrgpulse(0.6 * p_d, one, 0.0, 0.0);
decrgpulse(4.6 * p_d, three, 0.0, 0.0);
decrgpulse(7.2 * p_d, one, 0.0, 0.0);
decrgpulse(4.9 * p_d, three, 0.0, 0.0);
decrgpulse(7.4 * p_d, one, 0.0, 0.0);
decrgpulse(6.8 * p_d, three, 0.0, 0.0);
decrgpulse(7.0 * p_d, one, 0.0, 0.0);
decrgpulse(5.2 * p_d, three, 0.0, 0.0);
decrgpulse(5.4 * p_d, one, 0.0, 0.0);
decrgpulse(0.6 * p_d, three, 0.0, 0.0);
decrgpulse(4.5 * p_d, one, 0.0, 0.0);
decrgpulse(7.3 * p_d, three, 0.0, 0.0);
decrgpulse(5.1 * p_d, one, 0.0, 0.0);
decrgpulse(7.9 * p_d, three, 0.0, 0.0);
decrgpulse(4.9 * p_d, three, 0.0, 0.0);
decrgpulse(7.9 * p_d, one, 0.0, 0.0);
decrgpulse(5.0 * p_d, three, 0.0, 0.0);
decrgpulse(5.5 * p_d, one, 0.0, 0.0);
decrgpulse(0.6 * p_d, three, 0.0, 0.0);
decrgpulse(4.6 * p_d, one, 0.0, 0.0);
decrgpulse(7.2 * p_d, three, 0.0, 0.0);
decrgpulse(4.9 * p_d, one, 0.0, 0.0);
decrgpulse(7.4 * p_d, three, 0.0, 0.0);
decrgpulse(6.8 * p_d, one, 0.0, 0.0);
decrgpulse(7.0 * p_d, three, 0.0, 0.0);
decrgpulse(5.2 * p_d, one, 0.0, 0.0);
decrgpulse(5.4 * p_d, three, 0.0, 0.0);
decrgpulse(0.6 * p_d, one, 0.0, 0.0);
decrgpulse(4.5 * p_d, three, 0.0, 0.0);
decrgpulse(7.3 * p_d, one, 0.0, 0.0);
decrgpulse(5.1 * p_d, three, 0.0, 0.0);
decrgpulse(7.9 * p_d, one, 0.0, 0.0);
decrgpulse(4.9 * p_d, three, 0.0, 0.0);
decrgpulse(7.9 * p_d, one, 0.0, 0.0);
decrgpulse(5.0 * p_d, three, 0.0, 0.0);
decrgpulse(5.5 * p_d, one, 0.0, 0.0);
decrgpulse(0.6 * p_d, three, 0.0, 0.0);
decrgpulse(4.6 * p_d, one, 0.0, 0.0);
decrgpulse(7.2 * p_d, three, 0.0, 0.0);
decrgpulse(4.9 * p_d, one, 0.0, 0.0);
decrgpulse(7.4 * p_d, three, 0.0, 0.0);
decrgpulse(6.8 * p_d, one, 0.0, 0.0);
decrgpulse(7.0 * p_d, three, 0.0, 0.0);
decrgpulse(5.2 * p_d, one, 0.0, 0.0);
decrgpulse(5.4 * p_d, three, 0.0, 0.0);
decrgpulse(0.6 * p_d, one, 0.0, 0.0);
decrgpulse(4.5 * p_d, three, 0.0, 0.0);
decrgpulse(7.3 * p_d, one, 0.0, 0.0);
decrgpulse(5.1 * p_d, three, 0.0, 0.0);
decrgpulse(7.9 * p_d, one, 0.0, 0.0);
decrgpulse(4.9 * p_d, one, 0.0, 0.0);
decrgpulse(7.9 * p_d, three, 0.0, 0.0);
decrgpulse(5.0 * p_d, one, 0.0, 0.0);
decrgpulse(5.5 * p_d, three, 0.0, 0.0);
decrgpulse(0.6 * p_d, one, 0.0, 0.0);
decrgpulse(4.6 * p_d, three, 0.0, 0.0);
decrgpulse(7.2 * p_d, one, 0.0, 0.0);
decrgpulse(4.9 * p_d, three, 0.0, 0.0);
decrgpulse(7.4 * p_d, one, 0.0, 0.0);
decrgpulse(6.8 * p_d, three, 0.0, 0.0);
decrgpulse(7.0 * p_d, one, 0.0, 0.0);
decrgpulse(5.2 * p_d, three, 0.0, 0.0);
decrgpulse(5.4 * p_d, one, 0.0, 0.0);
decrgpulse(0.6 * p_d, three, 0.0, 0.0);
decrgpulse(4.5 * p_d, one, 0.0, 0.0);
decrgpulse(7.3 * p_d, three, 0.0, 0.0);
decrgpulse(5.1 * p_d, one, 0.0, 0.0);
decrgpulse(7.9 * p_d, three, 0.0, 0.0);
endhardloop();
}
decrgpulse(9.0 * p_d / 5.0, t9, 2.0e-6, 0.0);
if (H2Opurge[A] == 'y')
{
obspwrf(1000);
rgpulse(900 * pw, zero, 0.0, 0.0);
rgpulse(500 * pw, one, 0.0, 0.0);
obspwrf(4095.0);
}
zgradpulse(gzlvl7, gt7);
decpwrf(rf0);
delay(50.0e-6);
rgpulse(pw, zero, 0.0, 0.0);
zgradpulse(gzlvl7, gt7 / 1.6);
decrgpulse(pwC, three, 100.0e-6, 0.0);
zgradpulse(gzlvl5, gt5);
decphase(zero);
delay(tauc - gt5);
simpulse(2.0 * pw, 2.0 * pwC, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl5, gt5);
delay(tauc - gt5);
decrgpulse(pwC, zero, 0.0, 0.0);
zgradpulse(gzlvl3, gt3);
if (dm3[B] == 'y') /* turns off 2H decoupling */
{
setstatus(DEC3ch, FALSE, 'c', FALSE, dmf3);
dec3rgpulse(1 / dmf3, three, 2.0e-6, 2.0e-6);
dec3blank();
lk_autotrig(); /* resumes lock pulsing */
}
delay(2.0e-4);
rgpulse(pw, zero, 0.0, 0.0);
zgradpulse(gzlvl6, gt5);
delay(taua - gt5 + rof1);
simpulse(2.0 * pw, 2.0 * pwC, zero, zero, 0.0, rof1);
zgradpulse(gzlvl6, gt5);
if (STUD[A] == 'y')
decpower(studlvl);
else
decpower(dpwr);
dec2power(dpwr2);
delay(taua - gt5 - 2.0 * POWER_DELAY);
rgpulse(pw, zero, 0.0, rof2);
rcvron();
if (dm3[B] == 'y')
lk_sample();
setreceiver(t11);
if ((STUD[A] == 'y') && (dm[C] == 'y'))
{
decprgon(stCdec, 1.0 / stdmf, 1.0);
decon();
if (dm2[C] == 'y')
{
setstatus(DEC2ch, TRUE, dmm2[C], FALSE, dmf2);
}
}
else
status(C);
}
pulsesequence()
{
/* DECLARE AND LOAD VARIABLES; parameters used in the last half of the */
/* sequence are declared and initialized as 0.0 in bionmr.h, and */
/* reinitialized below */
char f1180[MAXSTR], /* Flag to start t1 @ halfdwell */
f2180[MAXSTR], /* Flag to start t2 @ halfdwell */
stCshape[MAXSTR],
TROSY[MAXSTR]; /* do TROSY on N15 and H1 */
int t1_counter, /* used for states tppi in t1 */
t2_counter, /* used for states tppi in t2 */
ni = getval("ni"),
ni2 = getval("ni2");
double d2_init=0.0, /* used for states tppi in t1 */
d3_init=0.0, /* used for states tppi in t2 */
tau1, /* t1 delay */
tauCH = getval("tauCH"), /* 1/4J delay for CH */
timeTN = getval("timeTN"), /* constant time for 15N evolution */
timeNCA = getval("timeNCA"),
timeC = getval("timeC"), /* other delays */
tauCC = getval("tauCC"),
zeta = getval("zeta"),
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
compC = getval("compC"),
rf0,
rfst,
widthHd,
pwS1, /* length of square 90 on Cab */
pwS2, /* length of square 180 on Ca */
phi7cal = getval("phi7cal"), /* phase in degrees of the last C13 90 pulse */
phshift = getval("phshift"), /* phase shift induced on CO by 180 on CA in middle of t1 */
pwNlvl = getval("pwNlvl"), /* power for N15 pulses */
pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */
sw1 = getval("sw1"),
sw2 = getval("sw2"),
waltzB1 = getval("waltzB1"),
gt0 = getval("gt0"), /* other gradients */
gt3 = getval("gt3"),
gt4 = getval("gt4"),
gzlvl0 = getval("gzlvl0"),
gzlvl3 = getval("gzlvl3"),
gzlvl4 = getval("gzlvl4");
getstr("f1180",f1180);
getstr("f2180",f2180);
getstr("TROSY",TROSY);
widthHd=2.069*(waltzB1/sfrq); /* produces same field as std. sequence */
/* LOAD PHASE TABLE */
settable(t1,2,phi1);
settable(t2,4,phi2);
settable(t4,1,phx);
if (TROSY[A]=='y')
{settable(t8,1,phy);
settable(t9,1,phx);
settable(t10,1,phy);
settable(t11,1,phx);
settable(t12,4,recT);}
else
{settable(t8,1,phx);
settable(t9,16,phi9);
settable(t10,1,phx);
settable(t11,1,phy);
settable(t12,8,rec);}
/* INITIALIZE VARIABLES */
kappa = 5.4e-3;
lambda = 2.4e-3;
/* maximum fine power for pwC pulses (and initialize rfst) */
rf0 = 4095.0; rfst=0.0;
if( pwC > 20.0*600.0/sfrq )
{ printf("increase pwClvl so that pwC < 20*600/sfrq");
psg_abort(1); }
/* 30 ppm sech/tanh inversion for Ca-Carbons */
rfst = (compC*4095.0*pwC*4000.0*sqrt((4.5*sfrq/600.0+3.85)/0.41));
rfst = (int) (rfst + 0.5);
strcpy(stCshape, "stC30");
/* get calculated pulse lengths of shaped C13 pulses */
pwS1 = c13pulsepw("co", "ca", "sinc", 90.0);
pwS2 = c13pulsepw("ca", "co", "square", 180.0);
/* CHECK VALIDITY OF PARAMETER RANGES */
if ( gt4 > zeta - 0.6*pwC)
{ printf(" gt4 is too big. Make gt4 equal to %f or less.\n",
(zeta - 0.6*pwC)); psg_abort(1);}
if ( 0.5*ni*1/(sw1) > 2.0*timeC + tauCC - OFFSET_DELAY - SAPS_DELAY)
{ printf(" ni is too big. Make ni equal to %d or less.\n",
((int)((2.0*timeC - OFFSET_DELAY)*2.0*sw1))); psg_abort(1);}
if ( dm[A] == 'y' || dm[B] == 'y' || dm[C] == 'y' )
{ printf("incorrect dec1 decoupler flags! Should be 'nnn' "); psg_abort(1);}
if ( dm2[A] == 'y' || dm2[B] == 'y' )
{ printf("incorrect dec2 decoupler flags! Should be 'nny' "); psg_abort(1);}
if ( dm3[A] == 'y' || dm3[C] == 'y' )
{ printf("incorrect dec3 decoupler flags! Should be 'nyn' or 'nnn' ");
psg_abort(1);}
if ( dpwr2 > 46 )
{ printf("dpwr2 too large! recheck value "); psg_abort(1);}
if ( pw > 20.0e-6 )
{ printf(" pw too long ! recheck value "); psg_abort(1);}
if ( pwN > 100.0e-6 )
{ printf(" pwN too long! recheck value "); psg_abort(1);}
if ( TROSY[A]=='y' && dm2[C] == 'y' )
{ text_error("Choose either TROSY='n' or dm2='n' ! "); psg_abort(1);}
/* PHASES AND INCREMENTED TIMES */
/* Phase incrementation for hypercomplex 2D data, States-Haberkorn element */
if (phase1 == 2) tsadd(t2,1,4);
if (TROSY[A]=='y')
{ if (phase2 == 2) icosel = +1;
else {tsadd(t4,2,4); tsadd(t10,2,4); icosel = -1;}
}
else { if (phase2 == 2) {tsadd(t10,2,4); icosel = +1;}
else icosel = -1;
}
/* C13 TIME INCREMENTATION and set up f1180 */
/* Set up f1180 */
tau1 = d2;
if((f1180[A] == 'y') && (ni > 1.0))
{ tau1 += ( 1.0 / (2.0*sw1) ); if(tau1 < 0.2e-6) tau1 = 0.0; }
tau1 = tau1/2.0;
/* Set up f2180 */
tau2 = d3;
if((f2180[A] == 'y') && (ni2 > 1.0))
{ tau2 += ( 1.0 / (2.0*sw2) ); if(tau2 < 0.2e-6) tau2 = 0.0; }
tau2 = tau2/2.0;
/* Calculate modifications to phases for States-TPPI acquisition */
if( ix == 1) d2_init = d2;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if(t1_counter % 2)
{ tsadd(t2,2,4); tsadd(t12,2,4); }
if( ix == 1) d3_init = d3;
t2_counter = (int) ( (d3-d3_init)*sw2 + 0.5 );
if(t2_counter % 2)
{ tsadd(t8,2,4); tsadd(t12,2,4); }
/* BEGIN PULSE SEQUENCE */
status(A);
delay(d1);
if (dm3[B]=='y') lk_hold();
rcvroff();
set_c13offset("ca");
obsoffset(tof);
obspower(tpwr);
obspwrf(4095.0);
decpower(pwClvl);
decpwrf(4095.0);
dec2power(pwNlvl);
txphase(three);
delay(1.0e-5);
dec2rgpulse(pwN, zero, 0.0, 0.0); /*destroy N15 and C13 magnetization*/
decrgpulse(pwC, zero, 0.0, 0.0);
zgradpulse(gzlvl0, 0.5e-3);
delay(1.0e-4);
dec2rgpulse(pwN, one, 0.0, 0.0);
decrgpulse(pwC, zero, 0.0, 0.0);
zgradpulse(0.7*gzlvl0, 0.5e-3);
delay(5.0e-4);
if(dm3[B] == 'y') /*optional 2H decoupling on */
{dec3unblank(); dec3rgpulse(1/dmf3, one, 0.0, 0.0);
dec3unblank(); setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);}
rgpulse(pw, zero, 0.0, 0.0); /* 1H pulse excitation */
txphase(zero);
decphase(zero);
zgradpulse(gzlvl0, gt0); /* 2.0*GRADIENT_DELAY */
decpwrf(rfst);
delay(tauCH - gt0 - WFG2_START_DELAY - 0.5e-3 + 70.0e-6);
simshaped_pulse("",stCshape, 2.0*pw, 1.0e-3, zero, zero, 0.0, 0.0);
delay(tauCH - gt0 - 0.5e-3 + 70.0e-6 - 150.0e-6);
decpwrf(rf0);
zgradpulse(gzlvl0, gt0); /* 2.0*GRADIENT_DELAY */
delay(150.0e-6);
rgpulse(pw, one, 0.0, 0.0);
zgradpulse(gzlvl3, gt3);
delay(2.0e-4);
decrgpulse(pwC, t1, 0.0, 0.0);
set_c13offset("co");
delay(zeta - 0.6*pwC - OFFSET_DELAY - POWER_DELAY - PWRF_DELAY - PRG_START_DELAY);
h1decon("DIPSI2", widthHd, 0.0); /*POWER_DELAY+PWRF_DELAY+PRG_START_DELAY */
delay(2.0*timeC - zeta);
c13pulse("co", "ca", "sinc", 90.0, t2, 0.0, 0.0); /* pwS1 */
delay(timeNCA - tau1);
c13pulse("ca", "co", "sinc", 180.0, zero, 2.0e-6, 2.0e-6);
sim3_c13pulse("", "co", "ca", "square", "", 0.0, 180.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0); /* pwS2 */
delay(timeNCA + tau1 + (60.0e-6));
initval(phshift, v3);
decstepsize(1.0);
dcplrphase(v3);
c13pulse("co", "ca", "sinc", 90.0, one, 0.0, 0.0); /* pwS1 */
delay(2.0*timeC + tauCC - OFFSET_DELAY - SAPS_DELAY - tau1);
c13pulse("ca", "co", "sinc", 180.0, zero, 0.0, 0.0);
delay(tauCC);
sim3_c13pulse("", "co", "ca", "square", "", 0.0, 180.0, 2.0*pwN, zero, zero, zero, 0.0, 60.0e-6);
delay(tau1);
set_c13offset("ca");
initval(phi7cal, v7);
decstepsize(1.0);
dcplrphase(v7); /* SAPS_DELAY */
dec2phase(t8);
nh_evol_se_train("ca", "co"); /* common part of sequence in bionmr.h */
if (dm3[B] == 'y') lk_sample();
}
pulsesequence()
{
/* DECLARE VARIABLES */
char satmode[MAXSTR],
fscuba[MAXSTR],
cbdecseq[MAXSTR],
chirp_shp[MAXSTR], /* name of variable containing name of Pbox shape */
fco180[MAXSTR], /* Flag for checking sequence */
fca180[MAXSTR], /* Flag for checking sequence */
sel_flg[MAXSTR];
int icosel,
ni = getval("ni"),
t1_counter; /* used for states tppi in t1 */
double d2_init=0.0, /* used for states tppi in t1 */
tau1, /* t1 delay */
tau2, /* t2 delay */
tau3, /* t2 delay */
taua, /* ~ 1/4JNH = 2.25 ms */
taub, /* ~ 1/4JNH = 2.25 ms */
zeta, /* time for C'-N to refocuss set to 0.5*24.0 ms */
bigTN, /* nitrogen T period */
BigT1, /* delay to compensate for gradient gt5 */
satpwr, /* low level 1H trans.power for presat */
sw1, /* sweep width in f1 */
sw2, /* sweep width in f2 */
cophase, /* phase correction for CO evolution */
caphase, /* phase correction for Ca evolution */
cbpwr, /* power level for selective CB decoupling */
cbdmf, /* pulse width for selective CB decoupling */
cbres, /* decoupling resolution of CB decoupling */
pwS1, /* length of 90 on Ca */
pwS2, /* length of 90 on CO */
pwS3, /* length of 180 on Ca */
pwS4, /* length of 180 on CO */
pwS5, /* CHIRP inversion pulse on CO and CA */
pwrS5=0.0, /* power of CHIRP pulse */
gt1,
gt2,
gt3,
gt4,
gt5,
gt6,
gt7,
gt8,
gt9,
gstab,
gzlvl1,
gzlvl2,
gzlvl3,
gzlvl4,
gzlvl5,
gzlvl6,
gzlvl7,
gzlvl8,
gzlvl9,
compH = getval("compH"), /* adjustment for amplifier compression */
pwHs = getval ("pwHs"), /* H1 90 degree pulse at tpwrs */
tpwrs, /* power for pwHs ("H2osinc") pulse */
waltzB1 = getval("waltzB1"),
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
compC = getval("compC"), /* ampl. compression */
pwNlvl = getval("pwNlvl"), /* power for N15 pulses */
pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */
swCa = getval("swCa"),
swCO = getval("swCO"),
swN = getval("swN"),
swTilt, /* This is the sweep width of the tilt vector */
cos_N, cos_CO, cos_Ca,
angle_N, angle_CO, angle_Ca;
angle_N=0.0;
/* LOAD VARIABLES */
getstr("satmode",satmode);
getstr("fco180",fco180);
getstr("fca180",fca180);
getstr("fscuba",fscuba);
getstr("sel_flg",sel_flg);
taua = getval("taua");
taub = getval("taub");
zeta = getval("zeta");
bigTN = getval("bigTN");
BigT1 = getval("BigT1");
tpwr = getval("tpwr");
satpwr = getval("tsatpwr");
dpwr = getval("dpwr");
sw1 = getval("sw1");
sw2 = getval("sw2");
cophase = getval("cophase");
caphase = getval("caphase");
gt1 = getval("gt1");
gt2 = getval("gt2");
gt3 = getval("gt3");
gt4 = getval("gt4");
gt5 = getval("gt5");
gt6 = getval("gt6");
gt7 = getval("gt7");
gt8 = getval("gt8");
gt9 = getval("gt9");
gstab = getval("gstab");
gzlvl1 = getval("gzlvl1");
gzlvl2 = getval("gzlvl2");
gzlvl3 = getval("gzlvl3");
gzlvl4 = getval("gzlvl4");
gzlvl5 = getval("gzlvl5");
gzlvl6 = getval("gzlvl6");
gzlvl7 = getval("gzlvl7");
gzlvl8 = getval("gzlvl8");
gzlvl9 = getval("gzlvl9");
/* Load variable */
cbpwr = getval("cbpwr");
cbdmf = getval("cbdmf");
cbres = getval("cbres");
tau1 = 0;
tau2 = 0;
tau3 = 0;
cos_N = 0;
cos_CO = 0;
cos_Ca = 0;
getstr("cbdecseq", cbdecseq);
/* LOAD PHASE TABLE */
settable(t1,2,phi1);
settable(t2,2,phi2);
settable(t3,1,phi3);
settable(t4,8,phi4);
settable(t5,4,phi5);
settable(t6,8,rec);
/* get calculated pulse lengths of shaped C13 pulses */
pwS1 = c13pulsepw("ca", "co", "square", 90.0);
pwS2 = c13pulsepw("co", "ca", "sinc", 90.0);
pwS3 = c13pulsepw("ca","co","square",180.0);
pwS4 = c13pulsepw("co","ca","sinc",180.0);
/*this section creates the chirp pulse inverting both co and ca*/
/*Pcoca180 is the name of the shapelib file created */
/*chirp180 is a file produced by Pbox psg containing parameter values from shape*/
strcpy(chirp_shp,"Pcoca180");
if (FIRST_FID) /* make shape once */
chirp180 = pbox(chirp_shp, CHIRP180, CHIRP180ps, dfrq, compC*pwC, pwClvl);
pwrS5 = chirp180.pwr; /* get pulse power from file */
pwS5 = chirp180.pw; /* get pulse width from file */
tpwrs = tpwr - 20.0*log10(pwHs/(compH*pw*1.69)); /*needs 1.69 times more*/
tpwrs = (int) (tpwrs); /*power than a square pulse */
widthHd = 2.681*waltzB1/sfrq; /* bandwidth of H1 WALTZ16 decoupling */
pwHd = h1dec90pw("WALTZ16", widthHd, 0.0); /* H1 90 length for WALTZ16 */
/* CHECK VALIDITY OF PARAMETER RANGES */
if((dm[A] == 'y' || dm[B] == 'y' || dm[C] == 'y' ))
{
printf("incorrect dec1 decoupler flags! ");
psg_abort(1);
}
if((dm2[A] == 'y' || dm2[B] == 'y' || dm2[C] == 'y' ))
{
printf("incorrect dec2 decoupler flags! Should be 'nnn' ");
psg_abort(1);
}
if( satpwr > 6 )
{
printf("SATPWR too large !!! ");
psg_abort(1);
}
if( dpwr > 46 )
{
printf("don't fry the probe, DPWR too large! ");
psg_abort(1);
}
if( dpwr2 > 46 )
{
printf("don't fry the probe, DPWR2 too large! ");
psg_abort(1);
}
if( pwClvl > 62 )
{
printf("don't fry the probe, pwClvl too large! ");
psg_abort(1);
}
if( pw > 200.0e-6 )
{
printf("dont fry the probe, pw too high ! ");
psg_abort(1);
}
if( pwN > 200.0e-6 )
{
printf("dont fry the probe, pwN too high ! ");
psg_abort(1);
}
if( pwC > 200.0e-6 )
{
printf("dont fry the probe, pwC too high ! ");
psg_abort(1);
}
if( gt3 > 2.5e-3 )
{
printf("gt3 is too long\n");
psg_abort(1);
}
if( gt1 > 10.0e-3 || gt2 > 10.0e-3 || gt4 > 10.0e-3 || gt5 > 10.0e-3
|| gt6 > 10.0e-3 || gt7 > 10.0e-3 || gt8 > 10.0e-3
|| gt9 > 10.0e-3)
{
printf("gt values are too long. Must be < 10.0e-3 or gt11=50us\n");
psg_abort(1);
}
/* PHASES AND INCREMENTED TIMES */
/* Set up angles and phases */
angle_CO=getval("angle_CO"); cos_CO=cos(PI*angle_CO/180.0);
angle_Ca=getval("angle_Ca"); cos_Ca=cos(PI*angle_Ca/180.0);
if ( (angle_CO < 0) || (angle_CO > 90) )
{ printf ("angle_CO must be between 0 and 90 degree.\n"); psg_abort(1); }
if ( (angle_Ca < 0) || (angle_Ca > 90) )
{ printf ("angle_Ca must be between 0 and 90 degree.\n"); psg_abort(1); }
if ( 1.0 < (cos_CO*cos_CO + cos_Ca*cos_Ca) )
{
printf ("Impossible angles.\n"); psg_abort(1);
}
else
{
cos_N=sqrt(1.0- (cos_CO*cos_CO + cos_Ca*cos_Ca));
angle_N = 180.0*acos(cos_N)/PI;
}
swTilt=swCO*cos_CO + swCa*cos_Ca + swN*cos_N;
if (ix ==1)
{
printf("\n\nn\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n");
printf ("Maximum Sweep Width: \t\t %f Hz\n", swTilt);
printf ("Anlge_CO:\t%6.2f\n", angle_CO);
printf ("Anlge_Ca:\t%6.2f\n", angle_Ca);
printf ("Anlge_N :\t%6.2f\n", angle_N );
}
/* Set up hyper complex */
/* sw1 is used as symbolic index */
if ( sw1 < 1000 ) { printf ("Please set sw1 to some value larger than 1000.\n"); psg_abort(1); }
if (ix == 1) d2_init = d2;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if (t1_counter % 2) { tsadd(t2,2,4); tsadd(t6,2,4); }
if (phase1 == 1) { ;} /* CC */
else if (phase1 == 2) { tsadd(t1,1,4);} /* SC */
else if (phase1 == 3) { tsadd(t5,1,4); } /* CS */
else if (phase1 == 4) { tsadd(t1,1,4); tsadd(t5,1,4); } /* SS */
else { printf ("phase1 can only be 1,2,3,4. \n"); psg_abort(1); }
if (phase2 == 2) { tsadd(t4,2,4); icosel = +1; } /* N */
else icosel = -1;
tau1 = 1.0*t1_counter*cos_CO/swTilt;
tau2 = 1.0*t1_counter*cos_Ca/swTilt;
tau3 = 1.0*t1_counter*cos_N/swTilt;
tau1 = tau1/2.0; tau2 = tau2/2.0; tau3 = tau3/2.0;
/* CHECK VALIDITY OF PARAMETER RANGES */
if (bigTN - 0.5*ni*(cos_N/swTilt) < 0.2e-6)
{ printf(" ni is too big. Make ni equal to %d or less.\n",
((int)((bigTN )*2.0*swTilt/cos_N))); psg_abort(1);}
/* BEGIN ACTUAL PULSE SEQUENCE */
status(A);
set_c13offset("co"); /* set Dec1 carrier at Co */
obspower(satpwr); /* Set transmitter power for 1H presaturation */
obspwrf(4095.0);
decpower(pwClvl); /* Set Dec1 power for hard 13C pulses */
decpwrf(4095.0);
dec2power(pwNlvl); /* Set Dec2 power for 15N hard pulses */
dec2pwrf(4095.0);
/* Presaturation Period */
if (satmode[0] == 'y')
{
delay(2.0e-5);
rgpulse(d1,zero,2.0e-6,2.0e-6); /* presaturation */
obspower(tpwr); /* Set transmitter power for hard 1H pulses */
delay(2.0e-5);
if(fscuba[0] == 'y')
{
delay(2.2e-2);
rgpulse(pw,zero,2.0e-6,0.0);
rgpulse(2*pw,one,2.0e-6,0.0);
rgpulse(pw,zero,2.0e-6,0.0);
delay(2.2e-2);
}
}
else
{
delay(d1);
}
obspower(tpwr); /* Set transmitter power for hard 1H pulses */
txphase(one);
dec2phase(zero);
delay(1.0e-5);
/* Begin Pulses */
status(B);
rcvroff();
lk_hold();
delay(20.0e-6);
shiftedpulse("sinc", pwHs, 90.0, 0.0, one, 2.0e-6, 2.0e-6);
txphase(zero);
rgpulse(pw,zero,0.0,0.0); /* 90 deg 1H pulse */
delay(0.2e-6);
zgradpulse(gzlvl1, gt1);
delay(2.0e-6);
delay(taua - gt1 - 2.2e-6); /* taua <= 1/4JNH */
sim3pulse(2*pw,0.0,2*pwN,zero,zero,zero,0.0,0.0);
txphase(three); dec2phase(zero); decphase(zero);
delay(0.2e-6);
zgradpulse(gzlvl1, gt1);
delay(gstab);
delay(taua - gt1 - gstab - 2.0e-6);
if(sel_flg[A] == 'n') {
rgpulse(pw,three,2.0e-6,0.0);
delay(0.2e-6);
zgradpulse(gzlvl2, gt2);
delay(gstab);
dec2rgpulse(pwN,zero,0.0,0.0);
decpower(pwrS5);
delay( zeta -POWER_DELAY);
dec2rgpulse(2.0*pwN,zero,0.0,0.0);
decshapedpulse(chirp_shp, pwS5, zero, 0.0, 0.0);
decpower(pwClvl);
delay(zeta - pwS5 - POWER_DELAY - 2.0e-6);
dec2rgpulse(pwN,zero,2.0e-6,0.0);
}
else {
rgpulse(pw,one,2.0e-6,0.0);
initval(1.0,v3);
dec2stepsize(45.0);
dcplr2phase(v3);
delay(0.2e-6);
zgradpulse(gzlvl2, gt2);
delay(gstab);
dec2rgpulse(pwN,zero,0.0,0.0);
dcplr2phase(zero);
delay(1.34e-3 - SAPS_DELAY - 2.0*pw);
rgpulse(pw,one,0.0,0.0);
rgpulse(2.0*pw,zero,0.0,0.0);
rgpulse(pw,one,0.0,0.0);
decpower(pwrS5);
delay( zeta - 1.34e-3 - 2.0*pw -POWER_DELAY);
dec2rgpulse(2.0*pwN,zero,0.0,0.0);
decshapedpulse(chirp_shp, pwS5, zero, 0.0, 0.0);
decpower(pwClvl);
delay(zeta - pwS5 - POWER_DELAY - 2.0e-6);
dec2rgpulse(pwN,zero,2.0e-6,0.0);
}
dec2phase(zero); decphase(t1);
delay(0.2e-6);
zgradpulse(gzlvl3, gt3);
delay(gstab);
/* t1 period for CO evolution */
c13pulse("co", "ca", "sinc", 90.0, t1, 0.0, 0.0);
if (!strcmp(fco180, "y"))
{
delay(10.0e-6);
sim3_c13pulse("", "ca", "co", "square", "", 0.0, 180.0, 2.0*pwN,
zero, zero, zero, 2.0e-6, 2.0e-6);
decstepsize(1.0);
initval(cophase,v4);
dcplrphase(v4);
delay(10.0e-6);
}
else
{
if (tau1-2.0*pwS2/PI-pwN-WFG3_START_DELAY-POWER_DELAY-2.0e-6 > 0.0)
{
delay(tau1-2.0*pwS2/PI-pwN-WFG3_START_DELAY-POWER_DELAY-2.0e-6);
sim3_c13pulse("", "ca", "co", "square", "", 0.0, 180.0, 2.0*pwN,
zero, zero, zero, 2.0e-6, 2.0e-6);
decstepsize(1.0);
initval(cophase,v4);
dcplrphase(v4);
delay(tau1-2.0*pwS2/PI-pwN-SAPS_DELAY-WFG3_STOP_DELAY-POWER_DELAY-2.0e-6);
}
else
{
c13pulse("co", "ca", "sinc", 180.0, zero, 0.0, 0.0);
}
}
c13pulse("co", "ca", "sinc", 90.0, zero, 4.0e-6, 0.0);
dcplrphase(zero);
set_c13offset("ca"); /* change Dec1 carrier to Ca (55 ppm) */
delay(0.2e-6);
zgradpulse(gzlvl4, gt4);
delay(gstab);
/* t2 period for Ca evolution*/
/* Turn on D decoupling using the third decoupler */
dec3unblank(); dec3rgpulse(1/dmf3, one, 0.0, 0.0);
dec3unblank(); setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
/* Turn on D decoupling */
c13pulse("ca", "co", "square", 90.0, t5, 0.0, 0.0);
if (!strcmp(fca180, "y"))
{
delay(10.0e-6);
sim3_c13pulse("", "co", "ca", "sinc", "", 0.0, 180.0, 2.0*pwN,
zero, zero, zero, 2.0e-6, 2.0e-6);
decstepsize(1.0);
initval(caphase,v5);
dcplrphase(v5);
delay(10.0e-6);
}
else
{
if (tau2-pwN-2.0*pwS1/PI-WFG3_START_DELAY-2*POWER_DELAY-
-WFG_STOP_DELAY-WFG_START_DELAY-2.0e-6 > 0.0)
{
decpower(cbpwr);
decphase(zero);
decprgon(cbdecseq,1/cbdmf,cbres);
decon();
delay(tau2-pwN-2.0*pwS1/PI-WFG3_START_DELAY-2*POWER_DELAY-
WFG_STOP_DELAY-WFG_START_DELAY-2.0e-6);
decoff();
decprgoff();
decphase(zero); dec2phase(zero);
decpower(pwClvl);
sim3_c13pulse("", "co", "ca", "sinc", "", 0.0, 180.0, 2.0*pwN,
zero, zero, zero, 2.0e-6, 2.0e-6);
decpower(cbpwr);
decphase(zero);
decprgon(cbdecseq,1/cbdmf,cbres);
decon();
delay(tau2-pwN-2.0*pwS1/PI-SAPS_DELAY-WFG3_STOP_DELAY-2*POWER_DELAY-
WFG_STOP_DELAY-WFG_START_DELAY-2.0e-6);
decoff();
decprgoff();
decstepsize(1.0);
initval(caphase,v5);
dcplrphase(v5);
decpower(pwClvl);
}
else
{
c13pulse("ca", "co", "square", 180.0, zero, 0.0, 0.0);
}
}
c13pulse("ca", "co", "square", 90.0, zero, 4.0e-6, 0.0);
dcplrphase(zero);
/* Turn off D decoupling */
dec3rgpulse(1/dmf3, three, 0.0, 0.0); dec3blank();
setstatus(DEC3ch, FALSE, 'w', FALSE, dmf3); dec3blank();
/* Turn off D decoupling */
set_c13offset("co"); /* set carrier back to Co */
delay(0.2e-6);
zgradpulse(gzlvl9, gt9);
delay(gstab);
/* t3 period */
dec2rgpulse(pwN,t2,2.0e-6,0.0);
dec2phase(t3);
decpower(pwrS5);
delay(bigTN - tau3 -POWER_DELAY);
dec2rgpulse(2.0*pwN,t3,0.0,0.0);
decshapedpulse(chirp_shp, pwS5, zero, 0.0, 0.0);
decpower(pwClvl);
txphase(zero);
dec2phase(t4);
delay(0.2e-6);
zgradpulse(icosel*gzlvl5, gt5);
delay(gstab);
delay(bigTN - WFG_START_DELAY - pwS5 - WFG_STOP_DELAY
- gt5 - gstab - 2.0*GRADIENT_DELAY);
delay(tau3);
sim3pulse(pw,0.0,pwN,zero,zero,t4,0.0,0.0);
c13pulse("co", "ca", "sinc", 90.0, zero, 4.0e-6, 0.0);
set_c13offset("ca");
c13pulse("ca", "co", "square", 90.0, zero, 20.0e-6, 0.0);
delay(0.2e-6);
zgradpulse(gzlvl6, gt6);
delay(2.0e-6);
dec2phase(zero);
delay(taub - POWER_DELAY - 4.0e-6 - pwS1 - 20.0e-6 - pwS2 - gt6 - 2.2e-6);
sim3pulse(2*pw,0.0,2*pwN,zero,zero,zero,0.0,0.0);
set_c13offset("co");
delay(0.2e-6);
zgradpulse(gzlvl6, gt6);
delay(gstab);
txphase(one);
dec2phase(one);
delay(taub - gt6 - gstab);
sim3pulse(pw,0.0,pwN,one,zero,one,0.0,0.0);
delay(0.2e-6);
zgradpulse(gzlvl7, gt7);
delay(2.0e-6);
txphase(zero);
dec2phase(zero);
delay(taub - gt7 - 2.2e-6);
sim3pulse(2*pw,0.0,2*pwN,zero,zero,zero,0.0,0.0);
delay(0.2e-6);
zgradpulse(gzlvl7, gt7);
delay(gstab);
delay(taub - gt7 - gstab);
sim3pulse(pw,0.0,pwN,zero,zero,zero,0.0,0.0);
delay(0.2e-6);
zgradpulse(-gzlvl8, gt8/2.0);
delay(gstab);
delay(BigT1 - gt8/2.0 - gstab - 0.5*(pwN - pw) - 2.0*pw/PI);
rgpulse(2*pw,zero,0.0,0.0);
delay(0.2e-6);
zgradpulse(gzlvl8, gt8/2.0);
delay(gstab);
dec2power(dpwr2);
decpower(dpwr);
delay(BigT1 - gt8/2.0 - gstab - 2.0*POWER_DELAY);
lk_sample();
status(C);
setreceiver(t6);
}
pulsesequence()
{
/* DECLARE AND LOAD VARIABLES; parameters used in the last half of the */
/* sequence are declared and initialized as 0.0 in bionmr.h, and */
/* reinitialized below */
char sel_flg[MAXSTR], autocal[MAXSTR],
glyshp[MAXSTR];
int t1_counter, /* used for states tppi in t1 */
ni = getval("ni");
double d2_init=0.0, /* used for states tppi in t1 */
tau1,
tau2,
tau3,
glypwr,glypwrf, /* Power levels for Cgly selective 90 */
pwgly, /* Pulse width for Cgly selective 90 */
bw,ppm, /* Used for autocal Cgly selective 90*/
tauCC = getval("tauCC"), /* delay for Ca to Cb cosy */
timeTN = getval("timeTN"), /* constant time for 15N evolution */
waltzB1 = getval("waltzB1"),
pwC = getval("pwC"), /* C13 pulse at pwClvl */
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
compC = getval("compC"), /* correction for amplifier compression*/
pwCa180,
pwCO180,
pwCab90,
pwCab180,
pwS1, /* length of square 90 on Cab */
phshift = getval("phshift"), /* phase shift on Cab by 180 on CO in t1 */
pwS2, /* length of 180 on CO */
pwS3,
pwS = getval("pwS"), /*used to change 180 on CO in t1 for 1D calibration */
pwZ, /* the largest of pwS2 and 2.0*pwN */
pwZ1, /* the largest of pwS2 and 2.0*pwN for 1D experiments */
pwNlvl = getval("pwNlvl"), /* power for N15 pulses */
pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */
sw1 = getval("sw1"),
swCb = getval("swCb"),
swCa = getval("swCa"),
swN = getval("swN"),
swTilt, /* This is the sweep width of the tilt vector */
cos_N, cos_Ca, cos_Cb,
angle_N, angle_Ca, angle_Cb, /* angle_N is calculated automatically */
gstab = getval("gstab"),
gt1 = getval("gt1"), gzlvl1 = getval("gzlvl1"),
gzlvl2 = getval("gzlvl2"),
gt3 = getval("gt3"), gzlvl3 = getval("gzlvl3"),
gt4 = getval("gt4"), gzlvl4 = getval("gzlvl4"),
gt5 = getval("gt5"), gzlvl5 = getval("gzlvl5"),
gt6 = getval("gt6"), gzlvl6 = getval("gzlvl6"),
gt7 = getval("gt7"), gzlvl7 = getval("gzlvl7"),
gt8 = getval("gt8"), gzlvl8 = getval("gzlvl8");
angle_N=0.0;
/* Load variables */
glypwrf = getval("glypwrf");
glypwr = getval("glypwr");
pwgly = getval("pwgly");
tau1 = 0; tau2 = 0; tau3 = 0;
cos_N = 0; cos_Ca = 0; cos_Cb = 0;
getstr("autocal", autocal);
getstr("glyshp", glyshp);
getstr("sel_flg",sel_flg);
/* LOAD PHASE TABLE */
settable(t2,1,phy); settable(t3,2,phi3);
settable(t5,4,phi5); settable(t6,8,phi6);
settable(t8,1,phy); settable(t9,1,phx); settable(t10,1,phx);
settable(t11,1,phx); settable(t12,8,recT);
/* INITIALIZE VARIABLES */
lambda = 2.4e-3;
pwCa180=c13pulsepw("ca", "co", "square", 180.0);
pwCO180=c13pulsepw("co", "ca", "sinc", 180.0);
pwCab90=c13pulsepw("cab","co","square",90.0);
pwCab180=c13pulsepw("cab","co","square",180.0);
pwHs = 1.7e-3*500.0/sfrq; /* length of H2O flipback, 1.7ms at 500 MHz*/
widthHd = 2.861*(waltzB1/sfrq); /* bw of H1 WALTZ16 decoupling */
pwHd = h1dec90pw("WALTZ16", widthHd, 0.0); /* H1 90 length for WALTZ16 */
/* get calculated pulse lengths of shaped C13 pulses */
pwS1 = c13pulsepw("cab", "co", "square", 90.0);
pwS2 = c13pulsepw("co", "cab", "sinc", 180.0);
pwS3 = c13pulsepw("cab", "co", "square", 180.0);
/* the 180 pulse on CO at the middle of t1 */
if (pwS2 > 2.0*pwN) pwZ = pwS2; else pwZ = 2.0*pwN;
if ((pwS==0.0) && (pwS2>2.0*pwN)) pwZ1=pwS2-2.0*pwN; else pwZ1=0.0;
if ( ni > 1 ) pwS = 180.0;
if ( pwS > 0 ) phshift = 140.0;
else phshift = 0.0;
/* CHECK VALIDITY OF PARAMETER RANGES */
if ( dm[A] == 'y' || dm[B] == 'y' || dm[C] == 'y' )
{ printf("incorrect dec1 decoupler flags! Should be 'nnn' "); psg_abort(1);}
if ( dm2[A] == 'y' || dm2[B] == 'y' || dm3[C] == 'y' )
{ printf("incorrect dec2 decoupler flags! Should be 'nnn' "); psg_abort(1);}
if ( dm3[A] == 'y' || dm3[C] == 'y' )
{ printf("incorrect dec3 decoupler flags! Should be 'nyn' or 'nnn' ");
psg_abort(1);}
if ( dpwr2 > 46 )
{ printf("dpwr2 too large! recheck value "); psg_abort(1);}
if ( pw > 20.0e-6 )
{ printf(" pw too long ! recheck value "); psg_abort(1);}
if ( pwN > 100.0e-6 )
{ printf(" pwN too long! recheck value "); psg_abort(1);}
/* PHASES AND INCREMENTED TIMES */
/* Set up angles and phases */
angle_Cb=getval("angle_Cb"); cos_Cb=cos(PI*angle_Cb/180.0);
angle_Ca=getval("angle_Ca"); cos_Ca=cos(PI*angle_Ca/180.0);
if ( (angle_Cb < 0) || (angle_Cb > 90) )
{ printf ("angle_Cb must be between 0 and 90 degree.\n"); psg_abort(1); }
if ( (angle_Ca < 0) || (angle_Ca > 90) )
{ printf ("angle_Ca must be between 0 and 90 degree.\n"); psg_abort(1); }
if ( 1.0 < (cos_Cb*cos_Cb + cos_Ca*cos_Ca) )
{
printf ("Impossible angles.\n"); psg_abort(1);
}
else
{
cos_N=sqrt(1.0- (cos_Cb*cos_Cb + cos_Ca*cos_Ca));
angle_N = 180.0*acos(cos_N)/PI;
}
swTilt=swCb*cos_Cb + swCa*cos_Ca + swN*cos_N;
if (ix ==1)
{
if ( 0.5*ni*(cos_N/swTilt) > timeTN - WFG3_START_DELAY)
{ printf(" ni is too big. Make ni equal to %d or less.\n",
((int)((timeTN - WFG3_START_DELAY)*2.0*swTilt/cos_N))); psg_abort(1);}
if ( (0.5*ni*cos_Ca/swTilt) > (tauCC - pwCO180 - pwCab180/2 - WFG2_START_DELAY -
2.0*PWRF_DELAY - 2.0*POWER_DELAY - WFG2_STOP_DELAY - 4.0e-6))
{ printf (" ni is too big. Make ni equal to %d or less. \n",
(int) ((tauCC - pwCO180 - pwCab180/2 - WFG2_START_DELAY - 2.0*PWRF_DELAY
-2.0*POWER_DELAY - WFG2_STOP_DELAY -14.0e-6)/(0.5*cos_Ca/swTilt)));
psg_abort(1); }
printf("\n\nn\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n");
printf ("Maximum Sweep Width: \t\t %f Hz\n", swTilt);
printf ("Angle_Cb:\t%6.2f\n", angle_Cb);
printf ("Angle_Ca:\t%6.2f\n", angle_Ca);
printf ("Angle_N :\t%6.2f\n", angle_N );
}
/* Set up hyper complex */
/* sw1 is used as symbolic index */
if ( sw1 < 1000 ) { printf ("Please set sw1 to some value larger than 1000.\n"); psg_abort(1); }
if (ix == 1) d2_init = d2;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if (t1_counter % 2) { tsadd(t8,2,4); tsadd(t12,2,4); }
if (phase1 == 1) { ;} /* CC */
else if (phase1 == 2) { tsadd(t3,3,4); tsadd(t2,3,4);} /* SC */
else if (phase1 == 3) { tsadd(t5,1,4); } /* CS */
else if (phase1 == 4) { tsadd(t3,3,4); tsadd(t2,3,4); tsadd(t5,1,4); } /* SS */
else { printf ("phase1 can only be 1,2,3,4. \n"); psg_abort(1); }
if (phase2 == 2) { tsadd(t10,2,4); icosel = +1; } /* N */
else icosel = -1;
tau1 = 1.0*t1_counter*cos_Cb/swTilt;
tau2 = 1.0*t1_counter*cos_Ca/swTilt;
tau3 = 1.0*t1_counter*cos_N/swTilt;
tau1 = tau1/2.0; tau2 = tau2/2.0; tau3 = tau3/2.0;
/* BEGIN PULSE SEQUENCE */
status(A);
delay(d1);
if (dm3[B] == 'y') lk_hold();
rcvroff();
obsoffset(tof); obspower(tpwr); obspwrf(4095.0);
set_c13offset("cab"); decpower(pwClvl); decpwrf(4095.0);
dec2power(pwNlvl);
txphase(one); delay(1.0e-5);
shiftedpulse("sinc", pwHs, 90.0, 0.0, one, 2.0e-6, 0.0);
txphase(zero); decphase(zero); dec2phase(zero);
delay(2.0e-6);
/* xxxxxxxxxxxxxxxxxxxxxx HN to N to Ca TRANSFER xxxxxxxxxxxxxxxxxx */
rgpulse(pw, zero, 0.0, 0.0); /* 1H pulse excitation */
dec2phase(zero);
zgradpulse(gzlvl3, gt3); /* G3 */
delay(lambda - gt3);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
if (sel_flg[A] == 'n') txphase(three);
else txphase(one);
zgradpulse(gzlvl3, gt3); /* G3 */
delay(lambda - gt3);
if (sel_flg[A] == 'n')
{
rgpulse(pw, three, 0.0, 0.0);
zgradpulse(gzlvl4, gt4); /* Crush gradient G4 */
delay(gstab);
/* Begin of N to Ca transfer */
dec2rgpulse(pwN, zero, 0.0, 0.0);
delay(timeTN - WFG3_START_DELAY);
}
else /* active suppresion */
{
rgpulse(pw,one,2.0e-6,0.0);
initval(1.0,v6); dec2stepsize(45.0); dcplr2phase(v6);
zgradpulse(gzlvl4, gt4); /* Crush gradient G4 */
delay(gstab);
/* Begin of N to Ca transfer */
dec2rgpulse(pwN,zero,0.0,0.0);
dcplr2phase(zero); /* SAPS_DELAY */
delay(1.34e-3 - SAPS_DELAY - 2.0*pw);
rgpulse(pw,one,0.0,0.0);
rgpulse(2.0*pw,zero,0.0,0.0);
rgpulse(pw,one,0.0,0.0);
delay(timeTN -1.34e-3 - 2.0*pw - WFG3_START_DELAY);
}
sim3_c13pulse("", "ca", "co", "square", "", 0.0, 180.0, 2.0*pwN,
zero, zero, zero, 2.0e-6, 2.0e-6);
dec2phase(one);
delay(timeTN);
dec2rgpulse(pwN, one, 0.0, 0.0);
/* xxxxxxxxxxxxxxxxxxxxxxxx END of N to CA TRANSFER xxxxxxxxxxxxxxxxxxxx */
setautocal();
set_c13offset("gly");
if (autocal[A] == 'n')
{
decpower(glypwr);
decpwrf(4095.0);
decphase(zero);
decshaped_pulse(glyshp,pwgly,zero,2.0e-6,0.0);
}
else
{
if(FIRST_FID)
{
ppm = getval("dfrq"); bw=9*ppm;
gly90 = pbox_make("gly90","eburp1",bw,0.0,compC*pwC,pwClvl);
/* Gly selective 90 with null at 50ppm */
}
pwgly=gly90.pw; glypwr=gly90.pwr; glypwrf=gly90.pwrf;
decpwrf(glypwrf);
decpower(glypwr);
decshaped_pulse("gly90",pwgly,zero,2.0e-6,0.0);
}
zgradpulse(gzlvl5, gt5); /* Crush gradient G5 */
set_c13offset("cab");
decphase(t3);
delay(gstab);
if (dm3[B] == 'y') /*optional 2H decoupling on */
{
dec3unblank(); dec3rgpulse(1/dmf3, one, 0.0, 0.0);
dec3unblank(); setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
}
/* xxxxxxxxxxxxxxxxxxxxxx 13CA to 13CB TRANSFER xxxxxxxxxxxxxxxxxx */
c13pulse("cab", "co", "square", 90.0, t3, 2.0e-6, 0.0);
decphase(zero);
delay(tauCC);
c13pulse("cab", "co", "square", 180.0, zero, 2.0e-6, 0.0);
decphase(t2);
delay(tauCC - POWER_DELAY - PWRF_DELAY - PRG_START_DELAY);
/* xxxxxxxxxxxxxxxxxxxxxx 13CB EVOLUTION xxxxxxxxxxxxxxxxxx */
c13pulse("cab", "co", "square", 90.0, t2, 2.0e-6, 0.0); /* pwS1 */
decphase(zero);
if ((ni>1.0) && (tau1>0.0))
{
if (tau1 - 2.0*pwCab90/PI - WFG_START_DELAY - pwN - 2.0e-6
- PWRF_DELAY - POWER_DELAY > 0.0)
{
delay(tau1 - 2.0*pwCab90/PI - pwN - 2.0e-6 );
dec2rgpulse(2.0*pwN, zero, 2.0e-6, 0.0);
delay(tau1 - 2.0*pwS1/PI - pwN - WFG_START_DELAY
- 2.0e-6 - PWRF_DELAY - POWER_DELAY);
}
else
{
tsadd(t12,2,4);
delay(2.0*tau1);
delay(10.0e-6); /* WFG_START_DELAY */
sim3_c13pulse("", "cab", "co", "square", "", 0.0, 180.0, 2.0*pwN,
zero, zero, zero, 2.0e-6, 0.0);
delay(10.0e-6);
}
}
else
{
tsadd(t12,2,4);
delay(10.0e-6); /* WFG_START_DELAY */
sim3_c13pulse("", "cab", "co", "square", "", 0.0, 180.0, 2.0*pwN,
zero, zero, zero, 2.0e-6, 0.0);
delay(10.0e-6);
}
decphase(t6);
c13pulse("cab", "co", "square", 90.0, t6, 2.0e-6, 0.0); /* pwS1 */
/* xxxxxxxxxxxx 13CB to 13CA BACK TRANSFER - CA EVOLUTION xxxxxxxxxxxxxx */
decphase(zero);
delay(tau2);
sim3_c13pulse("", "co", "ca", "sinc", "", 0.0, 180.0, 2.0*pwN,
zero, zero, zero, 2.0e-6, 0.0);
decphase(zero);
delay(tauCC- 2*pwN - pwCab180/2 - WFG2_START_DELAY - 2.0*PWRF_DELAY -
2.0*POWER_DELAY - WFG2_STOP_DELAY - 4.0e-6 );
c13pulse("cab", "co", "square", 180.0, zero, 2.0e-6, 0.0);
delay(tauCC - tau2 - pwCO180 - pwCab180/2 - WFG2_START_DELAY - 2.0*PWRF_DELAY
-2.0*POWER_DELAY - WFG2_STOP_DELAY - 4.0e-6 );
c13pulse("co", "ca", "sinc", 180.0, zero, 2.0e-6, 0.0);
decphase(t5);
c13pulse("cab", "co", "square", 90.0, t5, 2.0e-6, 0.0); /* pwS1 */
/* xxxxxxxxxxx END of 13CB to 13CA BACK TRANSFER - CA EVOLUTION xxxxxxxxxxxx */
if (dm3[B] == 'y') /*optional 2H decoupling off */
{
dec3rgpulse(1/dmf3, three, 0.0, 0.0); dec3blank();
setstatus(DEC3ch, FALSE, 'w', FALSE, dmf3); dec3blank();
}
dec2phase(t8);
zgradpulse(gzlvl6, gt6); /* Crush gradient G6 */
delay(gstab);
/* xxxxxxxxxxxxxxxx 13CA to 15N BACK TRANSFER - 15N EVOLUTION xxxxxxxxxxxxxx */
dec2rgpulse(pwN, t8, 2.0e-6, 2.0e-6);
decphase(zero);
dec2phase(t9);
delay(timeTN - WFG3_START_DELAY - tau3);
/* WFG3_START_DELAY */
sim3_c13pulse("", "ca", "co", "square", "", 0.0, 180.0, 2.0*pwN,
zero, zero, t9, 2.0e-6, 2.0e-6);
dec2phase(t10);
delay (timeTN - pwCO180 - WFG_START_DELAY - 2.0*POWER_DELAY
- 2.0*PWRF_DELAY - 2.0e-6 - gt1 - 2.0*GRADIENT_DELAY - gstab);
zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
delay(gstab - POWER_DELAY - PWRF_DELAY);
c13pulse("co", "ca", "sinc", 180.0, zero, 2.0e-6, 0.0); /*pwCO180*/
delay(tau3);
sim3pulse(pw, 0.0, pwN, zero, zero, t10, 0.0, 0.0); /* t4??*/
zgradpulse(gzlvl7, gt7); /* G7 */
txphase(zero);
dec2phase(zero);
delay (lambda - 1.3*pwN - gt7);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl7, gt7); /* G7 */
txphase(one);
dec2phase(one);
delay (lambda - 1.3*pwN - gt7);
sim3pulse(pw, 0.0, pwN, one, zero, one, 0.0, 0.0);
zgradpulse(gzlvl8, gt8); /* G8 */
txphase(zero);
dec2phase(zero);
delay (lambda - 1.3*pwN - gt8);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl8, gt8); /* G8 */
delay (lambda - 1.3*pwN - gt8);
sim3pulse(pw, 0.0, pwN, zero, zero, zero, 0.0, 0.0);
dec2power(dpwr2); decpower(dpwr);
delay ( (gt1/10.0) + 1.0e-4 + 2.0*GRADIENT_DELAY + POWER_DELAY);
rgpulse(2.0*pw, zero, 0.0, 0.0);
zgradpulse(icosel*gzlvl2, gt1/10.0); /* 2.0*GRADIENT_DELAY */
statusdelay(C, 1.0e-4);
setreceiver(t12);
if (dm3[B] == 'y') lk_sample();
}
pulsesequence()
{
/* DECLARE AND LOAD VARIABLES */
void makeHHdec(), makeCdec(); /* utility functions */
char f1180[MAXSTR], /* Flag to start t1 @ halfdwell */
mag_flg[MAXSTR], /* magic-angle coherence transfer gradients */
C13refoc[MAXSTR], /* C13 sech/tanh pulse in middle of t1*/
NH2only[MAXSTR], /* spectrum of only NH2 groups */
T1[MAXSTR], /* insert T1 relaxation delay */
T1rho[MAXSTR], /* insert T1rho relaxation delay */
T2[MAXSTR], /* insert T2 relaxation delay */
TROSY[MAXSTR], /* do TROSY on N15 and H1 */
Hdecflg[MAXSTR], /* HH-h**o decoupling flag */
Cdecflg[MAXSTR]; /* low power C-13 decoupling flag */
int icosel, /* used to get n and p type */
ihh=1, /* used in HH decouling to improve water suppression */
t1_counter, /* used for states tppi in t1 */
rTnum, /* number of relaxation times, relaxT */
rTcounter; /* to obtain maximum relaxT, ie relaxTmax */
double tau1, /* t1 delay */
lambda = 0.91/(4.0*getval("JNH")), /* 1/4J H1 evolution delay */
tNH = 1.0/(4.0*getval("JNH")), /* 1/4J N15 evolution delay */
relaxT = getval("relaxT"), /* total relaxation time */
rTarray[1000], /* to obtain maximum relaxT, ie relaxTmax */
maxrelaxT = getval("maxrelaxT"), /* maximum relaxT in all exps */
ncyc, /* number of pulsed cycles in relaxT */
pwr_dly, /* power delay */
/* the sech/tanh pulse is automatically calculated by the macro "proteincal", */
/* and is called directly from your shapelib. */
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
rf0, /* maximum fine power when using pwC pulses */
rfst, /* fine power for the stCall pulse */
compH = getval("compH"), /* adjustment for H1 amplifier compression */
compN = getval("compN"), /* adjustment for N15 amplifier compression */
compC = getval("compC"), /* adjustment for C13 amplifier compression */
calH = getval("calH"), /* multiplier on a pw pulse for H1 calibration */
tpwrsf = getval("tpwrsf"), /* fine power adustment for soft pulse */
pwHs = getval("pwHs"), /* H1 90 degree pulse length at tpwrs */
pwHH = 0.0, /* pwHH = pwHs for HH h**o-decoupling */
tpwrs, /* power for the pwHs ("H2Osinc") pulse */
pwNlvl = getval("pwNlvl"), /* power for N15 pulses */
pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */
calN = getval("calN"), /* multiplier on a pwN pulse for calibration */
slNlvl, /* power for N15 spin lock */
slNrf = 1500.0, /* RF field in Hz for N15 spin lock at 600 MHz */
sw1 = getval("sw1"),
gt1 = getval("gt1"), /* coherence pathway gradients */
gzcal = getval("gzcal"), /* dac to G/cm conversion */
gzlvl1 = getval("gzlvl1"),
gzlvl2 = getval("gzlvl2"),
BPpwrlimits, /* =0 for no limit, =1 for limit */
gt0 = getval("gt0"), /* other gradients */
gt3 = getval("gt3"),
gt4 = getval("gt4"),
gt5 = getval("gt5"),
gstab = getval("gstab"),
gzlvl0 = getval("gzlvl0"),
gzlvl3 = getval("gzlvl3"),
gzlvl4 = getval("gzlvl4"),
gzlvl5 = getval("gzlvl5");
P_getreal(GLOBAL,"BPpwrlimits",&BPpwrlimits,1);
getstr("f1180",f1180);
getstr("mag_flg",mag_flg);
getstr("C13refoc",C13refoc);
getstr("NH2only",NH2only);
getstr("T1",T1);
getstr("T1rho",T1rho);
getstr("T2",T2);
getstr("TROSY",TROSY);
getstr("Hdecflg", Hdecflg);
getstr("Cdecflg", Cdecflg);
/* LOAD PHASE TABLE */
settable(t3,2,phi3);
settable(t4,1,phx);
if (TROSY[A]=='y')
{settable(t1,1,ph_x);
settable(t9,1,phx);
settable(t10,1,phy);
settable(t11,1,phx);
settable(t12,2,recT);}
else
{settable(t1,1,phx);
settable(t9,8,phi9);
settable(t10,1,phx);
settable(t11,1,phy);
settable(t12,4,rec);}
/* INITIALIZE VARIABLES */
/* maximum fine power for pwC pulses (and initialize rfst) */
rf0 = 4095.0; rfst=0.0;
/* 180 degree adiabatic C13 pulse from 0 to 200 ppm */
if (C13refoc[A]=='y')
{rfst = (compC*4095.0*pwC*4000.0*sqrt((30.0*sfrq/600.0+7.0)/0.35));
rfst = (int) (rfst + 0.5);
if ( 1.0/(4000.0*sqrt((30.0*sfrq/600.0+7.0)/0.35)) < pwC )
{ text_error( " Not enough C13 RF. pwC must be %f usec or less.\n",
(1.0e6/(4000.0*sqrt((30.0*sfrq/600.0+7.0)/0.35))) ); psg_abort(1); }}
/* selective H20 one-lobe sinc pulse */
if(pwHs > 1e-6)
tpwrs = tpwr - 20.0*log10(pwHs/(compH*pw*1.69)); /* needs 1.69 times more */
else /* power than a square pulse */
tpwrs = 0.0;
tpwrs = (int) (tpwrs);
if (tpwrsf<4095.0) tpwrs = tpwrs + 6.0;
if (tpwrsf < 4095.0)
{
tpwrs = tpwrs + 6.0;
pwr_dly = POWER_DELAY + PWRF_DELAY;
}
else pwr_dly = POWER_DELAY;
/* power level for N15 spinlock (90 degree pulse length calculated first) */
slNlvl = 1/(4.0*slNrf*sfrq/600.0) ;
slNlvl = pwNlvl - 20.0*log10(slNlvl/(pwN*compN));
slNlvl = (int) (slNlvl + 0.5);
/* use 1/8J times for relaxation measurements of NH2 groups */
if ( (NH2only[A]=='y') && ((T1[A]=='y') || (T1rho[A]=='y') || (T2[A]=='y')) )
{ tNH = tNH/2.0; }
/* reset calH and calN for 2D if inadvertently left at 2.0 */
if (ni>1.0) {calH=1.0; calN=1.0;}
/* make shapes and set up parameters for HH h**o-decoupling */
if(Cdecflg[0] == 'y') makeCdec();
if(Hdecflg[0] == 'y') makeHHdec();
if(Hdecflg[0] != 'n')
{
pwHH = pwHs;
pwHs = 0.0;
}
/* CHECK VALIDITY OF PARAMETER RANGES */
if ((TROSY[A]=='y') && (gt1 < -2.0e-4 + pwHs + 1.0e-4 + 2.0*POWER_DELAY))
{ text_error( " gt1 is too small. Make gt1 equal to %f or more.\n",
(-2.0e-4 + pwHs + 1.0e-4 + 2.0*POWER_DELAY) ); psg_abort(1); }
if((dm[A] == 'y' || dm[B] == 'y' || dm[C] == 'y' ))
{ text_error("incorrect dec1 decoupler flags! Should be 'nnn' "); psg_abort(1); }
if((dm2[A] == 'y' || dm2[B] == 'y'))
{ text_error("incorrect dec2 decoupler flags! Should be 'nny' "); psg_abort(1); }
if( dpwr2 > 50 )
{ text_error("don't fry the probe, DPWR2 too large! "); psg_abort(1); }
if( pw > 50.0e-6 )
{ text_error("dont fry the probe, pw too high ! "); psg_abort(1); }
if( pwN > 100.0e-6 )
{ text_error("dont fry the probe, pwN too high ! "); psg_abort(1); }
/* RELAXATION TIMES AND FLAGS */
/* evaluate maximum relaxT, relaxTmax chosen by the user */
rTnum = getarray("relaxT", rTarray);
relaxTmax = rTarray[0];
for (rTcounter=1; rTcounter<rTnum; rTcounter++)
if (relaxTmax < rTarray[rTcounter]) relaxTmax = rTarray[rTcounter];
/* compare relaxTmax with maxrelaxT */
if (maxrelaxT > relaxTmax) relaxTmax = maxrelaxT;
if ( ((T1rho[A]=='y') || (T2[A]=='y')) && (relaxTmax > d1) )
{ text_error("Maximum relaxation time, relaxT, is greater than d1 ! "); psg_abort(1);}
if ( ((T1[A]=='y') && (T1rho[A]=='y')) || ((T1[A]=='y') && (T2[A]=='y')) ||
((T1rho[A]=='y') && (T2[A]=='y')) )
{ text_error("Choose only one relaxation measurement ! "); psg_abort(1); }
if ( ((T1[A]=='y') || (T1rho[A]=='y')) &&
((relaxT*100.0 - (int)(relaxT*100.0+1.0e-4)) > 1.0e-6) )
{ text_error("Relaxation time, relaxT, must be zero or multiple of 10msec"); psg_abort(1);}
if ( (T2[A]=='y') &&
(((relaxT+0.01)*50.0 - (int)((relaxT+0.01)*50.0+1.0e-4)) > 1.0e-6) )
{ text_error("Relaxation time, relaxT, must be odd multiple of 10msec"); psg_abort(1);}
if ( ((T1rho[A]=='y') || (T2[A]=='y')) && (relaxTmax > 0.25) && (ix==1) )
{ printf("WARNING, sample heating will result for relaxT>0.25sec"); }
if ( ((T1rho[A]=='y') || (T2[A]=='y')) && (relaxTmax > 0.5) )
{ text_error("relaxT greater than 0.5 seconds will heat sample"); psg_abort(1);}
if ( ((NH2only[A]=='y') || (T1[A]=='y') || (T1rho[A]=='y') || (T2[A]=='y'))
&& (TROSY[A]=='y') )
{ text_error("TROSY not implemented with NH2 spectrum, or relaxation exps."); psg_abort(1);}
if ((TROSY[A]=='y') && (dm2[C] == 'y'))
{ text_error("Choose either TROSY='n' or dm2='n' ! "); psg_abort(1); }
/* PHASES AND INCREMENTED TIMES */
/* Phase incrementation for hypercomplex 2D data, States-Haberkorn element */
if (TROSY[A]=='y')
{ if (phase1 == 2) icosel = -1;
else { tsadd(t4,2,4); tsadd(t10,2,4); icosel = +1; }
}
else { if (phase1 == 2) {tsadd(t10,2,4); icosel = +1;}
else icosel = -1;
}
if(Hdecflg[0] != 'n') ihh = icosel;
/* Set up f1180 */
tau1 = d2;
if((f1180[A] == 'y') && (ni > 1.0))
{ tau1 += ( 1.0 / (2.0*sw1) ); if(tau1 < 0.2e-6) tau1 = 0.0; }
tau1 = tau1/2.0;
/* Calculate modifications to phases for States-TPPI acquisition */
if( ix == 1) d2_init = d2;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if(t1_counter % 2)
{ tsadd(t3,2,4); tsadd(t12,2,4); }
/* Correct inverted signals for NH2 only spectra */
if ((NH2only[A]=='y') && (T1[A]=='n') && (T1rho[A]=='n') && (T2[A]=='n'))
{ tsadd(t3,2,4); }
/* BEGIN PULSE SEQUENCE */
status(A);
obspower(tpwr);
decpower(pwClvl);
decpwrf(rf0);
dec2power(pwNlvl);
txphase(zero);
decphase(zero);
dec2phase(zero);
if(Hdecflg[0] != 'n')
{
delay(5.0e-5);
rgpulse(pw,zero,rof1,0.0);
rgpulse(pw,one,0.0,rof1);
zgradpulse(1.5*gzlvl0, 0.5e-3);
delay(5.0e-4);
rgpulse(pw,zero,rof1,0.0);
rgpulse(pw,one,0.0,rof1);
zgradpulse(-gzlvl0, 0.5e-3);
}
delay(d1);
/* xxxxxxxxxxxxxxxxx CONSTANT SAMPLE HEATING FROM N15 RF xxxxxxxxxxxxxxxxx */
if (T1rho[A]=='y')
{dec2power(slNlvl);
dec2rgpulse(relaxTmax-relaxT, zero, 0.0, 0.0);
dec2power(pwNlvl);}
if (T2[A]=='y')
{ncyc = 8.0*100.0*(relaxTmax - relaxT);
if (BPpwrlimits > 0.5)
{
dec2power(pwNlvl-3.0); /* reduce for probe protection */
pwN=pwN*compN*1.4;
}
if (ncyc > 0)
{initval(ncyc,v1);
loop(v1,v2);
delay(0.625e-3 - pwN);
dec2rgpulse(2*pwN, zero, 0.0, 0.0);
delay(0.625e-3 - pwN);
endloop(v2);}
if (BPpwrlimits > 0.5)
{
dec2power(pwNlvl); /* restore normal value */
pwN=getval("pwN");
}
}
/* xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx */
rcvroff();
if (TROSY[A]=='n')
dec2rgpulse(pwN, zero, 0.0, 0.0); /*destroy N15 magnetization*/
zgradpulse(gzlvl0, 0.5e-3);
delay(1.0e-4);
if (TROSY[A]=='n') dec2rgpulse(pwN, one, 0.0, 0.0);
zgradpulse(0.7*gzlvl0, 0.5e-3);
decpwrf(rfst);
txphase(t1);
delay(5.0e-4);
if ( dm3[B] == 'y' ) /* begins optional 2H decoupling */
{
lk_hold();
dec3rgpulse(1/dmf3,one,10.0e-6,2.0e-6);
dec3unblank();
dec3phase(zero);
delay(2.0e-6);
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
}
rgpulse(calH*pw,t1,0.0,0.0); /* 1H pulse excitation */
txphase(zero);
dec2phase(zero);
zgradpulse(gzlvl0, gt0);
delay(lambda - gt0 - pwHH);
if(Hdecflg[0] != 'n')
{
obspower(tpwrs);
if (tpwrsf<4095.0) obspwrf(tpwrsf);
shaped_pulse("H2Osinc", pwHH, two, 5.0e-5, 0.0);
obspower(tpwr);
if (tpwrsf<4095.0) obspwrf(4095.0);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
obspower(tpwrs);
if (tpwrsf<4095.0) obspwrf(tpwrsf);
shaped_pulse("H2Osinc", pwHH, two, 5.0e-5, 0.0);
obspower(tpwr);
if (tpwrsf<4095.0) obspwrf(4095.0);
}
else
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
txphase(one);
zgradpulse(gzlvl0, gt0);
delay(lambda - gt0 - pwHH);
rgpulse(pw, one, 0.0, 0.0);
txphase(two);
obspower(tpwrs);
if (tpwrsf<4095.0) obspwrf(tpwrsf);
shaped_pulse("H2Osinc", pwHs, two, 5.0e-5, 0.0);
obspower(tpwr);
if (tpwrsf<4095.0) obspwrf(4095.0);
if (TROSY[A]=='y')
zgradpulse(ihh*gzlvl3, gt3);
else
zgradpulse(-ihh*gzlvl3, gt3);
dec2phase(t3);
delay(2.0e-4);
dec2rgpulse(calN*pwN, t3, 0.0, 0.0);
txphase(zero);
decphase(zero);
/* xxxxxxxxxxxxxxxxxx OPTIONS FOR N15 RELAXATION xxxxxxxxxxxxxxxxxxxx */
if ( (T1[A]=='y') || (T1rho[A]=='y') || (T2[A]=='y') )
{
dec2phase(one);
zgradpulse(gzlvl4, gt4); /* 2.0*GRADIENT_DELAY */
delay(tNH - gt4 - 2.0*GRADIENT_DELAY);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, one, 0.0, 0.0);
zgradpulse(gzlvl4, gt4); /* 2.0*GRADIENT_DELAY */
delay(tNH - gt4 - 2.0*GRADIENT_DELAY);
}
/* xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx */
if (T1[A]=='y')
{
dec2rgpulse(pwN, one, 0.0, 0.0);
dec2phase(three);
zgradpulse(gzlvl0, gt0); /* 2.0*GRADIENT_DELAY */
delay(2.5e-3 - gt0 - 2.0*GRADIENT_DELAY - pw);
rgpulse(2.0*pw, zero, 0.0, 0.0);
delay(2.5e-3 - pw);
ncyc = (100.0*relaxT);
initval(ncyc,v4);
if (ncyc > 0)
{loop(v4,v5);
delay(2.5e-3 - pw);
rgpulse(2.0*pw, two, 0.0, 0.0);
delay(2.5e-3 - pw);
delay(2.5e-3 - pw);
rgpulse(2.0*pw, zero, 0.0, 0.0);
delay(2.5e-3 - pw);
endloop(v5);}
dec2rgpulse(pwN, three, 0.0, 0.0);
}
/* xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx */
/* Theory suggests 8.0 is better than 2PI as RF */
/* field multiplier and experiment confirms this.*/
if (T1rho[A]=='y') /* Shift evolution of 2.0*pwN/PI for one pulse */
{ /* at end left unrefocused as for normal sequence*/
delay(1.0/(8.0*slNrf) - pwN);
decrgpulse(pwN, zero, 0.0, 0.0);
dec2power(slNlvl);
/* minimum 5ms spinlock to dephase */
dec2rgpulse((2.5e-3-pw), zero, 0.0, 0.0); /* spins not locked */
sim3pulse(2.0*pw, 0.0, 2.0*pw, zero, zero, zero, 0.0, 0.0);
dec2rgpulse((2.5e-3-pw), zero, 0.0, 0.0);
ncyc = 100.0*relaxT;
initval(ncyc,v4); if (ncyc > 0)
{loop(v4,v5);
dec2rgpulse((2.5e-3-pw), zero, 0.0, 0.0);
sim3pulse(2.0*pw, 0.0, 2.0*pw, two, zero, zero, 0.0, 0.0);
dec2rgpulse((2.5e-3-pw), zero, 0.0, 0.0);
dec2rgpulse((2.5e-3-pw), zero, 0.0, 0.0);
sim3pulse(2.0*pw, 0.0, 2.0*pw, zero, zero, zero, 0.0, 0.0);
dec2rgpulse((2.5e-3-pw), zero, 0.0, 0.0);
endloop(v5);}
dec2power(pwNlvl);
decrgpulse(pwN, zero, 0.0, 0.0);
delay(1.0/(8.0*slNrf) + 2.0*pwN/PI - pwN);
}
/* xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx */
if (T2[A]=='y')
{
dec2phase(zero);
initval(0.0,v3); initval(180.0,v4);
if (BPpwrlimits > 0.5)
{
dec2power(pwNlvl-3.0); /* reduce for probe protection */
pwN=pwN*compN*1.4;
}
ncyc = 100.0*relaxT;
initval(ncyc,v5);
loop(v5,v6);
initval(3.0,v7);
loop(v7,v8);
delay(0.625e-3 - pwN);
dec2rgpulse(2.0*pwN, zero, 0.0, 0.0);
delay(0.625e-3 - pwN);
endloop(v8);
delay(0.625e-3 - pwN - SAPS_DELAY);
add(v4,v3,v3); obsstepsize(1.0); xmtrphase(v3); /* SAPS_DELAY */
dec2rgpulse(2.0*pwN, zero, 0.0, 0.0);
delay(0.625e-3 - pwN - pw);
rgpulse(2*pw, zero, 0.0, 0.0);
delay(0.625e-3 - pwN - pw );
dec2rgpulse(2.0*pwN, zero, 0.0, 0.0);
xmtrphase(zero); /* SAPS_DELAY */
delay(0.625e-3 - pwN - SAPS_DELAY);
initval(3.0,v9);
loop(v9,v10);
delay(0.625e-3 - pwN);
dec2rgpulse(2.0*pwN, zero, 0.0, 0.0);
delay(0.625e-3 - pwN);
endloop(v10);
endloop(v6);
if (BPpwrlimits > 0.5)
{
dec2power(pwNlvl); /* restore normal value */
pwN=getval("pwN");
}
}
/* xxxxxxxxxxxxxxxxxx OPTIONS FOR N15 EVOLUTION xxxxxxxxxxxxxxxxxxxxx */
txphase(zero);
dec2phase(t9);
if ( (NH2only[A]=='y') || (T1[A]=='y') || (T1rho[A]=='y') || (T2[A]=='y') )
{
delay(tau1);
/* optional sech/tanh pulse in middle of t1 */
if (C13refoc[A]=='y') /* WFG_START_DELAY */
{decshaped_pulse("stC200", 1.0e-3, zero, 0.0, 0.0);
delay(tNH - 1.0e-3 - WFG_START_DELAY - 2.0*pw);}
else
{delay(tNH - 2.0*pw);}
rgpulse(2.0*pw, zero, 0.0, 0.0);
if (tNH < gt1 + 1.99e-4) delay(gt1 + 1.99e-4 - tNH);
delay(tau1);
dec2rgpulse(2.0*pwN, t9, 0.0, 0.0);
if (mag_flg[A] == 'y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
txphase(t4);
dec2phase(t10);
if (tNH > gt1 + 1.99e-4) delay(tNH - gt1 - 2.0*GRADIENT_DELAY);
else delay(1.99e-4 - 2.0*GRADIENT_DELAY);
}
else if (TROSY[A]=='y')
{
if ( (C13refoc[A]=='y') && (tau1 > 0.5e-3 + WFG2_START_DELAY) )
{delay(tau1 - 0.5e-3 - WFG2_START_DELAY); /* WFG2_START_DELAY */
decshaped_pulse("stC200", 1.0e-3, zero, 0.0, 0.0);
delay(tau1 - 0.5e-3);}
else delay(2.0*tau1);
if (mag_flg[A] == 'y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
delay(2.0e-4 - 2.0*GRADIENT_DELAY);
dec2rgpulse(2.0*pwN, t9, 0.0, 0.0);
txphase(three);
delay(gt1 + 2.0e-4 - pwHs - 1.0e-4 - 2.0*pwr_dly);
obspower(tpwrs);
if (tpwrsf<4095.0) obspwrf(tpwrsf);
shaped_pulse("H2Osinc", pwHs, three, 5.0e-5, 0.0);
obspower(tpwr);
if (tpwrsf<4095.0) obspwrf(4095.0);
txphase(t4);
delay(5.0e-5);
}
else
{ /* fully-coupled spectrum */
if (dm2[C]=='n') {rgpulse(2.0*pw, zero, 0.0, 0.0); pw=0.0;}
if ( (C13refoc[A]=='y') && (tau1 > 0.5e-3 + WFG2_START_DELAY) )
{delay(tau1 - 0.5e-3 - WFG2_START_DELAY); /* WFG2_START_DELAY */
simshaped_pulse("", "stC200", 2.0*pw, 1.0e-3, zero, zero, 0.0, 0.0);
delay(tau1 - 0.5e-3);
delay(gt1 + 2.0e-4);}
else
{delay(tau1);
rgpulse(2.0*pw, zero, 0.0, 0.0);
delay(gt1 + 2.0e-4 - 2.0*pw);
delay(tau1);}
pw=getval("pw");
dec2rgpulse(2.0*pwN, t9, 0.0, 0.0);
if (mag_flg[A] == 'y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
txphase(t4);
dec2phase(t10);
delay(2.0e-4 - 2.0*GRADIENT_DELAY);
}
if (T1rho[A]=='y') delay(POWER_DELAY);
/* xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx */
if (TROSY[A]=='y') rgpulse(pw, t4, 0.0, 0.0);
else sim3pulse(pw, 0.0, pwN, t4, zero, t10, 0.0, 0.0);
txphase(zero);
dec2phase(zero);
zgradpulse(gzlvl5, gt5);
if (TROSY[A]=='y') delay(lambda - 0.65*(pw + pwN) - gt5);
else delay(lambda - 1.3*pwN - gt5);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl5, gt5);
txphase(one);
dec2phase(t11);
delay(lambda - 1.3*pwN - gt5);
sim3pulse(pw, 0.0, pwN, one, zero, t11, 0.0, 0.0);
txphase(zero);
dec2phase(zero);
zgradpulse(1.5*gzlvl5, gt5);
delay(lambda - 1.3*pwN - gt5);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
dec2phase(t10);
zgradpulse(1.5*gzlvl5, gt5);
if (TROSY[A]=='y') delay(lambda - 1.6*pwN - gt5);
else delay(lambda - 0.65*pwN - gt5);
if (TROSY[A]=='y') dec2rgpulse(pwN, t10, 0.0, 0.0);
else rgpulse(pw, zero, 0.0, 0.0);
delay((gt1/10.0) + 1.0e-4 +gstab - 0.65*pw + 2.0*GRADIENT_DELAY + POWER_DELAY);
if ( dm3[B] == 'y' ) /* turns off 2H decoupling */
{
setstatus(DEC3ch, FALSE, 'c', FALSE, dmf3);
dec3rgpulse(1/dmf3,three,2.0e-6,2.0e-6);
dec3blank();
lk_autotrig(); /* resumes lock pulsing */
}
rgpulse(2.0*pw, zero, 0.0, 0.0);
dec2power(dpwr2); /* POWER_DELAY */
if (mag_flg[A] == 'y') magradpulse(icosel*gzcal*gzlvl2, 0.1*gt1);
else zgradpulse(icosel*gzlvl2, 0.1*gt1); /* 2.0*GRADIENT_DELAY */
if(Cdecflg[0] == 'y')
{
delay(gstab-2.0*POWER_DELAY-PRG_START_DELAY+rof2);
rcvron();
statusdelay(C,1.0e-4);
if (dm3[B] == 'y')
{
delay(1/dmf3);
lk_sample();
}
setreceiver(t12);
pbox_decon(&Cdseq);
if(Hdecflg[0] == 'y')
homodec(&HHdseq);
}
else
{
delay(gstab+rof2);
rcvron();
statusdelay(C,1.0e-4);
if (dm3[B] == 'y')
{
delay(1/dmf3);
lk_sample();
}
setreceiver(t12);
if(Hdecflg[0] == 'y')
homodec(&HHdseq);
}
}
pulsesequence()
{
/* DECLARE AND LOAD VARIABLES */
char f1180[MAXSTR], /* Flag to start t1 @ halfdwell */
f2180[MAXSTR], /* Flag to start t2 @ halfdwell */
ribose[MAXSTR], /* ribose CHn groups only */
AH2H8[MAXSTR], /* Adenine H2-H8 correlation */
H2Opurge[MAXSTR],
rna_stCdec[MAXSTR], /* calls STUD+ waveforms from shapelib */
STUD[MAXSTR]; /* apply automatically calculated STUD decoupling */
int t1_counter, /* used for states tppi in t1 */
t2_counter; /* used for states tppi in t2 */
double tau1, /* t1 delay */
tau2, /* t2 delay */
stdmf = getval("dmf80"), /* dmf for 80 ppm of STUD decoupling */
rf80 = getval("rf80"), /* rf in Hz for 80ppm STUD+ */
taua = getval("taua"), /* time delays for CH coupling evolution */
taub = getval("taub"),
tauc = getval("tauc"),
/* string parameter rna_stCdec calls stud decoupling waveform from your shapelib.*/
studlvl, /* coarse power for STUD+ decoupling */
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
rfC, /* maximum fine power when using pwC pulses */
dofa, /* dof shifted to 80 ppm for ribose and 145 ppm for AH2H8 */
tofa, /* tof shifted to 7.5 ppm in t1 for AH2H8 */
/* p_d is used to calculate the isotropic mixing on the C-ribose region */
p_d, /* 50 degree pulse for DIPSI-3 at rfdC */
rfdC, /* fine power for 7.5 kHz or 4.0 kHz rf at 500MHz */
ncyc = getval("ncyc"), /* no. of cycles of DIPSI-3 */
compC = getval("compC"), /* adjustment for C13 amplifier compression */
pwNlvl = getval("pwNlvl"), /* power for N15 pulses */
pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */
sw1 = getval("sw1"),
sw2 = getval("sw2"),
grecov = getval("grecov"), /* Gradient recovery delay, typically 150-200us */
gt0 = getval("gt0"), /* other gradients */
gt3 = getval("gt3"),
gt4 = getval("gt4"),
gt5 = getval("gt5"),
gt7 = getval("gt7"),
gzlvl0 = getval("gzlvl0"),
gzlvl3 = getval("gzlvl3"),
gzlvl4 = getval("gzlvl4"),
gzlvl5 = getval("gzlvl5"),
gzlvl6 = getval("gzlvl6"),
gzlvl7 = getval("gzlvl7");
getstr("f1180",f1180);
getstr("f2180",f2180);
getstr("ribose",ribose);
getstr("AH2H8",AH2H8);
getstr("H2Opurge",H2Opurge);
getstr("STUD",STUD);
/* LOAD PHASE TABLE */
settable(t3,2,phi3);
settable(t5,4,phi5);
settable(t9,8,phi9);
settable(t11,8,rec);
/* INITIALIZE VARIABLES */
/* maximum fine power for pwC pulses */
rfC = 4095.0;
if (ribose[A] == 'y')
{
/* Center dof in RIBOSE region on 80ppm. */
tofa = tof;
dofa = dof - 30.0*dfrq;
/* dipsi-3 decoupling on C-ribose */
p_d = (5.0)/(9.0*4.0*7000.0*(sfrq/800)); /* 35ppm DIPSI-3 */
rfdC = (compC*4095.0*pwC*5.0)/(p_d*9.0);
rfdC = (int) (rfdC + 0.5);
ncyc = (int) (ncyc + 0.5);
}
else
{
/* Center dof in adenine C2-C4-C6-C8-C5 region on 145 ppm. */
tofa = tof + 2.5*sfrq;
dofa = dof + 35.0*dfrq;
/* dipsi-3 decoupling on C-aromatic */
p_d = (5.0)/(9.0*4.0*8000.0*(sfrq/800)); /* 40ppm DIPSI-3 */
rfdC = (compC*4095.0*pwC*5.0)/(p_d*9.0);
rfdC = (int) (rfdC + 0.5);
ncyc = (int) (ncyc + 0.5);
}
/* 80 ppm STUD+ decoupling */
strcpy(rna_stCdec, "wurst80");
studlvl = pwClvl + 20.0*log10(compC*pwC*4.0*rf80);
studlvl = (int) (studlvl + 0.5);
/* CHECK VALIDITY OF PARAMETER RANGES */
if((ribose[A] == 'y' && AH2H8[A] == 'y' ))
{ text_error("Choose either ribose='y' or AH2H8='y' !! ");
psg_abort(1); }
if((dm[A] == 'y' || dm[B] == 'y' ))
{ text_error("incorrect dec1 decoupler flags! Should be 'nny' or 'nnn' ");
psg_abort(1); }
if((dm2[A] == 'y' || dm2[B] == 'y'))
{ text_error("incorrect dec2 decoupler flags! Should be 'nny' or 'nnn' ");
psg_abort(1); }
if( (((dm[C] == 'y') && (dm2[C] == 'y')) && (STUD[A] == 'y')) )
{ text_error("incorrect dec2 decoupler flags! Should be 'nnn' if STUD='y'"); psg_abort(1); }
if((dm3[A] == 'y' || dm3[C] == 'y' ))
{ text_error("incorrect dec1 decoupler flags! Should be 'nyn' or 'nnn' "); psg_abort(1); }
if( dpwr > 50 )
{ text_error("don't fry the probe, DPWR too large! "); psg_abort(1); }
if( dpwr2 > 50 )
{ text_error("don't fry the probe, DPWR2 too large! "); psg_abort(1); }
if( (pw > 20.0e-6) && (tpwr > 56) )
{ text_error("don't fry the probe, pw too high ! "); psg_abort(1); }
if( (pwC > 40.0e-6) && (pwClvl > 56) )
{ text_error("don't fry the probe, pwN too high ! "); psg_abort(1); }
if( (pwN > 100.0e-6) && (pwNlvl > 56) )
{ text_error("don't fry the probe, pwN too high ! "); psg_abort(1); }
if ((dm3[B] == 'y' && dpwr3 > 44 ))
{ text_error ("Deuterium decoupling power too high ! "); psg_abort(1); }
if ((ncyc > 1 ) && (ix == 1))
{ text_error("mixing time is %f ms.\n",(ncyc*97.8*4*p_d)); }
/* PHASES AND INCREMENTED TIMES */
/* Phase incrementation for hypercomplex 2D data, States-Haberkorn element */
if (phase1 == 2)
tsadd(t3,1,4);
if (phase2 == 2)
tsadd(t5,1,4);
/* C13 TIME INCREMENTATION and set up f1180 */
/* Set up f1180 */
tau1 = d2;
if(f1180[A] == 'y')
{ tau1 += ( 1.0 / (2.0*sw1) ); if(tau1 < 0.2e-6) tau1 = 0.0; }
tau1 = tau1/2.0;
/* Set up f2180 */
tau2 = d3;
if(f2180[A] == 'y')
{ tau2 += ( 1.0 / (2.0*sw2) ); if(tau2 < 0.2e-6) tau2 = 0.0; }
tau2 = tau2/2.0;
/* Calculate modifications to phases for States-TPPI acquisition */
if( ix == 1) d2_init = d2;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if(t1_counter % 2)
{ tsadd(t3,2,4); tsadd(t11,2,4); }
if( ix == 1) d3_init = d3;
t2_counter = (int) ( (d3-d3_init)*sw2 + 0.5 );
if(t2_counter % 2)
{ tsadd(t5,2,4); tsadd(t11,2,4); }
/* BEGIN PULSE SEQUENCE */
status(A);
if (dm3[B] == 'y') lk_sample();
delay(d1);
if (dm3[B] == 'y') lk_hold();
rcvroff();
obspower(tpwr);
decpower(pwClvl);
dec2power(pwNlvl);
decpwrf(rfC);
obsoffset(tofa);
decoffset(dofa);
dec2offset(dof2);
txphase(t3);
delay(1.0e-5);
decrgpulse(pwC, zero, 0.0, 0.0); /*destroy C13 magnetization*/
zgradpulse(gzlvl0, 0.5e-3);
delay(grecov/2);
decrgpulse(pwC, one, 0.0, 0.0);
zgradpulse(0.7*gzlvl0, 0.5e-3);
delay(5.0e-4);
if (dm3[B] == 'y') /*optional 2H decoupling on */
{
dec3unblank();
dec3rgpulse(1/dmf3, one, 0.0, 0.0);
dec3unblank();
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
}
rgpulse(pw, t3, 0.0, 0.0); /* 1H pulse excitation */
zgradpulse(gzlvl0, gt0); /* 2.0*GRADIENT_DELAY */
decphase(zero);
delay(taua + tau1 - gt0 - 2.0*GRADIENT_DELAY - 2.0*pwC);
decrgpulse(2.0*pwC, zero, 0.0, 0.0);
txphase(zero);
delay(tau1);
rgpulse(2.0*pw, zero, 0.0, 0.0);
zgradpulse(gzlvl0, gt0);
txphase(one);
decphase(t5);
obsoffset(tof);
delay(taua - gt0);
rgpulse(pw, one, 0.0, 0.0);
zgradpulse(gzlvl3, gt3);
delay(grecov);
decrgpulse(pwC, t5, 0.0, 0.0);
delay(tau2);
dec2rgpulse(2.0*pwN, zero, 0.0, 0.0);
zgradpulse(gzlvl4, gt4); /* 2.0*GRADIENT_DELAY */
decphase(zero);
delay(taub - 2.0*pwN - gt4 - 2.0*GRADIENT_DELAY);
txphase(zero);
decpwrf(rfC);
delay(taub - 2.0*pw);
rgpulse(2.0*pw, zero, 0.0, 0.0);
delay(tau2);
decrgpulse(2.0*pwC, zero, 0.0, 0.0);
delay(taub);
zgradpulse(gzlvl4, gt4); /* 2.0*GRADIENT_DELAY */
decpwrf(rfdC);
delay(taub - gt4 - 2.0*GRADIENT_DELAY);
decrgpulse(1.0e-3, zero, 0.0, 0.0);
initval(ncyc, v2);
starthardloop(v2);
decrgpulse(4.9*p_d,one,0.0,0.0);
decrgpulse(7.9*p_d,three,0.0,0.0);
decrgpulse(5.0*p_d,one,0.0,0.0);
decrgpulse(5.5*p_d,three,0.0,0.0);
decrgpulse(0.6*p_d,one,0.0,0.0);
decrgpulse(4.6*p_d,three,0.0,0.0);
decrgpulse(7.2*p_d,one,0.0,0.0);
decrgpulse(4.9*p_d,three,0.0,0.0);
decrgpulse(7.4*p_d,one,0.0,0.0);
decrgpulse(6.8*p_d,three,0.0,0.0);
decrgpulse(7.0*p_d,one,0.0,0.0);
decrgpulse(5.2*p_d,three,0.0,0.0);
decrgpulse(5.4*p_d,one,0.0,0.0);
decrgpulse(0.6*p_d,three,0.0,0.0);
decrgpulse(4.5*p_d,one,0.0,0.0);
decrgpulse(7.3*p_d,three,0.0,0.0);
decrgpulse(5.1*p_d,one,0.0,0.0);
decrgpulse(7.9*p_d,three,0.0,0.0);
decrgpulse(4.9*p_d,three,0.0,0.0);
decrgpulse(7.9*p_d,one,0.0,0.0);
decrgpulse(5.0*p_d,three,0.0,0.0);
decrgpulse(5.5*p_d,one,0.0,0.0);
decrgpulse(0.6*p_d,three,0.0,0.0);
decrgpulse(4.6*p_d,one,0.0,0.0);
decrgpulse(7.2*p_d,three,0.0,0.0);
decrgpulse(4.9*p_d,one,0.0,0.0);
decrgpulse(7.4*p_d,three,0.0,0.0);
decrgpulse(6.8*p_d,one,0.0,0.0);
decrgpulse(7.0*p_d,three,0.0,0.0);
decrgpulse(5.2*p_d,one,0.0,0.0);
decrgpulse(5.4*p_d,three,0.0,0.0);
decrgpulse(0.6*p_d,one,0.0,0.0);
decrgpulse(4.5*p_d,three,0.0,0.0);
decrgpulse(7.3*p_d,one,0.0,0.0);
decrgpulse(5.1*p_d,three,0.0,0.0);
decrgpulse(7.9*p_d,one,0.0,0.0);
decrgpulse(4.9*p_d,three,0.0,0.0);
decrgpulse(7.9*p_d,one,0.0,0.0);
decrgpulse(5.0*p_d,three,0.0,0.0);
decrgpulse(5.5*p_d,one,0.0,0.0);
decrgpulse(0.6*p_d,three,0.0,0.0);
decrgpulse(4.6*p_d,one,0.0,0.0);
decrgpulse(7.2*p_d,three,0.0,0.0);
decrgpulse(4.9*p_d,one,0.0,0.0);
decrgpulse(7.4*p_d,three,0.0,0.0);
decrgpulse(6.8*p_d,one,0.0,0.0);
decrgpulse(7.0*p_d,three,0.0,0.0);
decrgpulse(5.2*p_d,one,0.0,0.0);
decrgpulse(5.4*p_d,three,0.0,0.0);
decrgpulse(0.6*p_d,one,0.0,0.0);
decrgpulse(4.5*p_d,three,0.0,0.0);
decrgpulse(7.3*p_d,one,0.0,0.0);
decrgpulse(5.1*p_d,three,0.0,0.0);
decrgpulse(7.9*p_d,one,0.0,0.0);
decrgpulse(4.9*p_d,one,0.0,0.0);
decrgpulse(7.9*p_d,three,0.0,0.0);
decrgpulse(5.0*p_d,one,0.0,0.0);
decrgpulse(5.5*p_d,three,0.0,0.0);
decrgpulse(0.6*p_d,one,0.0,0.0);
decrgpulse(4.6*p_d,three,0.0,0.0);
decrgpulse(7.2*p_d,one,0.0,0.0);
decrgpulse(4.9*p_d,three,0.0,0.0);
decrgpulse(7.4*p_d,one,0.0,0.0);
decrgpulse(6.8*p_d,three,0.0,0.0);
decrgpulse(7.0*p_d,one,0.0,0.0);
decrgpulse(5.2*p_d,three,0.0,0.0);
decrgpulse(5.4*p_d,one,0.0,0.0);
decrgpulse(0.6*p_d,three,0.0,0.0);
decrgpulse(4.5*p_d,one,0.0,0.0);
decrgpulse(7.3*p_d,three,0.0,0.0);
decrgpulse(5.1*p_d,one,0.0,0.0);
decrgpulse(7.9*p_d,three,0.0,0.0);
endhardloop();
decrgpulse(9.0*p_d/5.0, t9, 2.0e-6, 0.0);
if( H2Opurge[A] == 'y' )
{obspwrf(1000.0); rgpulse(900*pw, zero, 0.0, 0.0);
rgpulse(500*pw, one, 0.0, 0.0); obspwrf(4095.0); }
zgradpulse(gzlvl7, gt7);
decpwrf(rfC);
delay(50.0e-6);
rgpulse(pw,zero,0.0,0.0);
zgradpulse(gzlvl7, gt7/1.6);
decrgpulse(pwC, three, 100.0e-6, 0.0);
zgradpulse(gzlvl5, gt5);
decphase(zero);
delay(tauc - gt5);
simpulse(2.0*pw, 2.0*pwC, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl5, gt5);
delay(tauc - gt5);
decrgpulse(pwC, zero, 0.0, 0.0);
zgradpulse(gzlvl3, gt3);
if(dm3[B] == 'y') /*optional 2H decoupling off */
{
dec3rgpulse(1/dmf3, three, 0.0, 0.0);
dec3blank();
setstatus(DEC3ch, FALSE, 'w', FALSE, dmf3);
dec3blank();
}
delay(grecov);
rgpulse(pw, zero, 0.0, 0.0);
zgradpulse(gzlvl6, gt5);
delay(taua - gt5);
simpulse(2.0*pw, 2.0*pwC, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl6, gt5);
if (STUD[A]=='y') decpower(studlvl);
else
{
decpower(dpwr);
dec2power(dpwr2);
}
delay(taua - gt5);
rgpulse(pw, zero, 0.0, rof2);
rcvron();
if (dm3[B] == 'y') lk_sample();
setreceiver(t11);
if ((STUD[A]=='y') && (dm[C] == 'y'))
{
decpower(studlvl);
decunblank();
decon();
decprgon(rna_stCdec,1/stdmf, 1.0);
startacq(alfa);
acquire(np, 1.0/sw);
decprgoff();
decoff();
decblank();
}
else
status(C);
}
pulsesequence()
{
/* DECLARE AND LOAD VARIABLES */
char abfilter[MAXSTR], /* flag for selection of inner or outer pair of doublets */
NH2[MAXSTR], /* flag for selection of NH2 */
f1180[MAXSTR], /* Flag to start t1 @ halfdwell */
mag_flg[MAXSTR], /* magic-angle coherence transfer gradients */
C13refoc[MAXSTR]; /* C13 sech/tanh pulse in middle of t1*/
int icosel, /* used to get n and p type */
t1_counter; /* used for states tppi in t1 */
double tau1, /* t1 delay */
lambda = 0.91/(4.0*getval("JNH")), /* 1/4J H1 evolution delay */
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
rf0, /* maximum fine power when using pwC pulses */
rfst, /* fine power for the stCall pulse */
compH = getval("compH"), /* adjustment for H1 amplifier compression */
compC = getval("compC"), /* adjustment for C13 amplifier compression */
calH = getval("calH"), /* multiplier on a pw pulse for H1 calibration */
pwHs = getval("pwHs"), /* H1 90 degree pulse length at tpwrs */
tpwrsf_u = getval("tpwrsf_u"),/* fine power correction for flipback(up)*/
tpwrsf_d = getval("tpwrsf_d"),/* fine power correction for flipback(down)*/
tpwrs, /* power for the pwHs ("H2Osinc") pulse */
pwNlvl = getval("pwNlvl"), /* power for N15 pulses */
pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */
calN = getval("calN"), /* multiplier on a pwN pulse for calibration */
sw1 = getval("sw1"),
gt1 = getval("gt1"), /* coherence pathway gradients */
gzcal = getval("gzcal"), /* dac to G/cm conversion */
gzlvl1 = getval("gzlvl1"),
gzlvl2 = getval("gzlvl2"),
gstab = getval("gstab"), /* field recovery */
gt0 = getval("gt0"), /* other gradients */
gt3 = getval("gt3"),
gt5 = getval("gt5"),
gzlvl0 = getval("gzlvl0"),
gzlvl3 = getval("gzlvl3"),
gzlvl5 = getval("gzlvl5");
getstr("NH2",NH2);
getstr("f1180",f1180);
getstr("mag_flg",mag_flg);
getstr("C13refoc",C13refoc);
getstr("abfilter",abfilter);
/* LOAD PHASE TABLE */
settable(t3,2,phi3);
settable(t4,1,phx);
settable(t1,1,phx);
settable(t9,8,phi9);
settable(t10,1,phx);
settable(t12,4,rec);
/* INITIALIZE VARIABLES */
/* maximum fine power for pwC pulses (and initialize rfst) */
rf0 = 4095.0; rfst=0.0;
/* 180 degree adiabatic C13 pulse from 0 to 200 ppm */
if (C13refoc[A]=='y')
{rfst = (compC*4095.0*pwC*4000.0*sqrt((30.0*sfrq/600.0+7.0)/0.35));
rfst = (int) (rfst + 0.5);
if ( 1.0/(4000.0*sqrt((30.0*sfrq/600.0+7.0)/0.35)) < pwC )
{ text_error( " Not enough C13 RF. pwC must be %f usec or less.\n",
(1.0e6/(4000.0*sqrt((30.0*sfrq/600.0+7.0)/0.35))) ); psg_abort(1); }}
/* selective H20 one-lobe sinc pulse */
tpwrs = tpwr - 20.0*log10(pwHs/(compH*pw*1.69)); /*needs 1.69 times more*/
tpwrs = (int) (tpwrs); /*power than a square pulse */
if (tpwrsf_d<4095.0) tpwrs=tpwrs+6; /* nominal tpwrsf_d ~ 2048 */
/* tpwrsf_d,tpwrsf_u can be used to correct for radiation damping */
/* reset calH and calN for 2D if inadvertently left at 2.0 */
if (ni>1.0) {calH=1.0; calN=1.0;}
/* CHECK VALIDITY OF PARAMETER RANGES */
if((dm[A] == 'y' || dm[B] == 'y' || dm[C] == 'y' ))
{ text_error("incorrect dec1 decoupler flags! Should be 'nnn' "); psg_abort(1); }
if((dm2[A] == 'y' || dm2[B] == 'y' || dm2[C] == 'y' ))
{ text_error("incorrect dec2 decoupler flags! Should be 'nnn' "); psg_abort(1); }
if((NH2[A] != 'y') && (NH2[A] != 'n'))
{ text_error("NH2 should be 'y' or 'n'!"); psg_abort(1); }
if((abfilter[A] != 'a') && (abfilter[A] != 'b'))
{ text_error("abfilter should be 'a' or 'b'!"); psg_abort(1); }
if( dpwr2 > 46 )
{ text_error("don't fry the probe, DPWR2 too large! "); psg_abort(1); }
if( pw > 50.0e-6 )
{ text_error("dont fry the probe, pw too high ! "); psg_abort(1); }
if( pwN > 100.0e-6 )
{ text_error("dont fry the probe, pwN too high ! "); psg_abort(1); }
/* PHASES AND INCREMENTED TIMES */
/* Phase incrementation for hypercomplex 2D data, States-Haberkorn element */
if (phase1 == 1) {tsadd(t10,2,4); icosel = +1;}
else icosel = -1;
/* Set up f1180 */
tau1 = d2;
if((f1180[A] == 'y') && (ni > 1.0))
{ tau1 += ( 1.0 / (2.0*sw1) ); if(tau1 < 0.2e-6) tau1 = 0.0; }
tau1 = tau1/2.0;
/* Calculate modifications to phases for States-TPPI acquisition */
if( ix == 1) d2_init = d2;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if(t1_counter % 2)
{ tsadd(t3,2,4); tsadd(t12,2,4); }
/* BEGIN PULSE SEQUENCE */
status(A);
obspower(tpwr);
decpower(pwClvl);
decpwrf(rf0);
dec2power(pwNlvl);
txphase(zero);
decphase(zero);
dec2phase(zero);
delay(d1);
/* xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx */
rcvroff();
dec2rgpulse(pwN, zero, 0.0, 0.0);
decrgpulse(pwC, zero, 0.0, 0.0); /*destroy N15 and C13 magnetization*/
zgradpulse(gzlvl0, 0.5e-3);
delay(1.0e-4);
dec2rgpulse(pwN, one, 0.0, 0.0);
decrgpulse(pwC, one, 0.0, 0.0);
zgradpulse(0.7*gzlvl0, 0.5e-3);
decpwrf(rfst);
txphase(t1);
delay(5.0e-4);
if(dm3[B] == 'y') /*optional 2H decoupling on */
{lk_hold();
dec3unblank();
dec3rgpulse(1/dmf3, one, 0.0, 0.0);
dec3unblank();
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);}
rgpulse(calH*pw,t1,0.0,0.0); /* 1H pulse excitation */
txphase(zero);
dec2phase(zero);
zgradpulse(gzlvl0, gt0);
delay(lambda - gt0);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
txphase(one);
zgradpulse(gzlvl0, gt0);
delay(lambda - gt0);
rgpulse(pw, one, 0.0, 0.0);
txphase(two);
obspower(tpwrs); obspwrf(tpwrsf_d);
shaped_pulse("H2Osinc_d", pwHs, two, 5.0e-5, 0.0);
obspower(tpwr); obspwrf(4095.0);
zgradpulse(gzlvl3, gt3);
dec2phase(t3);
delay(gstab);
dec2rgpulse(calN*pwN, t3, 0.0, 0.0);
txphase(zero);
decphase(zero);
/* xxxxxxxxxxxxxxxxxx OPTIONS FOR N15 EVOLUTION xxxxxxxxxxxxxxxxxxxxx */
txphase(zero);
dec2phase(t9);
if ( (C13refoc[A]=='y') && (tau1 > 0.5e-3 + WFG2_START_DELAY) )
{delay(tau1 - 0.5e-3 - WFG2_START_DELAY); /* WFG2_START_DELAY */
simshaped_pulse("", "stC200", 2.0*pw, 1.0e-3, zero, zero, 0.0, 0.0);
decphase(zero);
delay(tau1 - 0.5e-3);
zgradpulse(-1*gzlvl1, 0.5*gt1);
delay(gstab - 2.0*GRADIENT_DELAY);}
else
{delay(tau1);
rgpulse(2.0*pw, zero, 0.0, 0.0);
delay(tau1);
zgradpulse(-1*gzlvl1, 0.5*gt1);
delay(gstab - 2.0*GRADIENT_DELAY);
}
dec2rgpulse(2.0*pwN, t9, 0.0, 0.0);
zgradpulse(gzlvl1, 0.5*gt1); /* 2.0*GRADIENT_DELAY */
txphase(t4);
dec2phase(t10);
delay(gstab - 2.0*GRADIENT_DELAY);
/* xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx */
sim3pulse(pw, 0.0, pwN, t4, zero, t10, 0.0, 0.0);
obspower(tpwrs); obspwrf(tpwrsf_u);
shaped_pulse("H2Osinc_u", pwHs, two, 5.0e-5, 0.0);
obspower(tpwr); obspwrf(4095.0);
txphase(zero);
dec2phase(zero);
zgradpulse(gzlvl5, gt5);
delay(lambda - 1.3*pwN - gt5 - pwHs - 5.0e-5 -2.0*POWER_DELAY);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl5, gt5);
txphase(one);
delay(lambda - 1.3*pwN - gt5);
if(abfilter[A] == 'a')
{
if (NH2[A] == 'n')
{
dec2rgpulse(pwN,one,0.0,0.0);
}
else
{
dec2rgpulse(pwN,zero,0.0,0.0);
}
}
else
{
if (NH2[A] == 'n')
{
dec2rgpulse(pwN,three,0.0,0.0);
}
else
{
dec2rgpulse(pwN,two,0.0,0.0);
}
}
delay(gt1/10.0 -pwN +gstab + 2.0*GRADIENT_DELAY + POWER_DELAY );
rgpulse(2.0*pw, zero, 0.0, 0.0);
dec2power(dpwr2); /* POWER_DELAY */
if (mag_flg[A] == 'y') magradpulse(gzcal*icosel*gzlvl2, 0.1*gt1);
else zgradpulse(icosel*gzlvl2, 0.1*gt1); /* 2.0*GRADIENT_DELAY */
delay(gstab);
if (dm3[B] == 'y') {delay(1/dmf3); lk_sample();}
setreceiver(t12);
}
pulsesequence()
{
/* DECLARE VARIABLES */
char fscuba[MAXSTR],
f1180[MAXSTR], /* Flag to start t1 @ fulldwell */
f2180[MAXSTR], /* Flag to start t2 @ halfdwell */
C_flg[MAXSTR],
dtt_flg[MAXSTR];
int phase, phase2, ni, ni2,
t1_counter, /* used for states tppi in t1 */
t2_counter; /* used for states tppi in t2 */
double tau1, /* t1 delay */
tau2, /* t2 delay */
taua, /* ~ 1/4JHC = 1.6 ms */
taub, /* 1/6JCH = 1.1 ms */
BigTC, /* Carbon constant time period = 1/4Jcc = 7.0 ms */
pwN, /* PW90 for 15N pulse @ pwNlvl */
pwC, /* PW90 for c nucleus @ pwClvl */
pwcrb180, /* PW180 for C 180 reburp @ rfrb */
pwClvl, /* power level for 13C pulses on dec1 */
compC, compH, /* compression factors for H1 and C13 amps */
rfrb, /* power level for 13C reburp pulse */
pwNlvl, /* high dec2 pwr for 15N hard pulses */
sw1, /* sweep width in f1 */
sw2, /* sweep width in f2 */
bw, ofs, ppm,
gt0,
gt1,
gt2,
gt3,
gt4,
gt5,
gt6,
gstab,
gzlvl0,
gzlvl1,
gzlvl2,
gzlvl3,
gzlvl4,
gzlvl5,
gzlvl6,
decstep1,
decstep2,
decstep3,
tpwrs,
pwHs,
dof_me, rfrb_cg, rfrb_co, pwrb_co, pwrb_cg,
tof_dtt,
rfca90,
pwca90,
rfca180,
pwca180,
pwco90,
dofCO;
/* LOAD VARIABLES */
getstr("f1180",f1180);
getstr("f2180",f2180);
getstr("fscuba",fscuba);
getstr("C_flg",C_flg);
getstr("dtt_flg",dtt_flg);
taua = getval("taua");
taub = getval("taub");
BigTC = getval("BigTC");
pwC = getval("pwC");
pwcrb180 = getval("pwcrb180");
pwN = getval("pwN");
tpwr = getval("tpwr");
pwClvl = getval("pwClvl");
compC = getval("compC");
compH = getval("compH");
dpwr = getval("dpwr");
pwNlvl = getval("pwNlvl");
phase = (int) ( getval("phase") + 0.5);
phase2 = (int) ( getval("phase2") + 0.5);
sw1 = getval("sw1");
sw2 = getval("sw2");
ni = getval("ni");
ni2 = getval("ni2");
gstab = getval("gstab");
gt0 = getval("gt0");
gt1 = getval("gt1");
gt2 = getval("gt2");
gt3 = getval("gt3");
gt4 = getval("gt4");
gt5 = getval("gt5");
gt6 = getval("gt6");
gzlvl0 = getval("gzlvl0");
gzlvl1 = getval("gzlvl1");
gzlvl2 = getval("gzlvl2");
gzlvl3 = getval("gzlvl3");
gzlvl4 = getval("gzlvl4");
gzlvl5 = getval("gzlvl5");
gzlvl6 = getval("gzlvl6");
decstep1 = getval("decstep1");
decstep2 = getval("decstep2");
decstep3 = getval("decstep3");
pwHs = getval("pwHs");
dof_me = getval("dof_me");
tof_dtt = getval("tof_dtt");
dofCO = getval("dofCO");
tpwrs = 0.0;
setautocal(); /* activate auto-calibration */
if(FIRST_FID) /* make shapes */
{
ppm = getval("dfrq");
bw = 80.0*ppm;
rb180 = pbox_make("rb180P", "reburp", bw, 0.0, compC*pwC, pwClvl);
bw = 8.125*ppm; ofs = -24.0*ppm;
rb180_cg = pbox_make("rb180_cgP", "reburp", bw, ofs, compC*pwC, pwClvl);
bw = 60*ppm; ofs = 136.0*ppm;
rb180_co = pbox_make("rb180_coP", "reburp", bw, ofs, compC*pwC, pwClvl);
bw = 118.0*ppm; ofs = -118.0*ppm;
ca180 = pbox_make("ca180P", "square180n", bw, ofs, compC*pwC, pwClvl);
bw = 118.0*ppm; ofs = 18.0*ppm;
ca90 = pbox_make("ca90P", "square90n", bw, ofs, compC*pwC, pwClvl);
}
pwcrb180 = rb180.pw; rfrb = rb180.pwrf; /* set up parameters */
pwrb_cg = rb180_cg.pw; rfrb_cg = rb180_cg.pwrf; /* set up parameters */
pwrb_co = rb180_co.pw; rfrb_co = rb180_co.pwrf; /* set up parameters */
pwca90 = ca90.pw; rfca90 = ca90.pwrf; /* set up parameters */
pwca180 = ca180.pw; rfca180 = ca180.pwrf; /* set up parameters */
pwco90 = pwca90;
tpwrs = tpwr - 20.0*log10(pwHs/((compH*pw)*1.69)); /* sinc=1.69xrect */
tpwrs = (int) (tpwrs);
/* LOAD PHASE TABLE */
settable(t1,2,phi1);
settable(t2,4,phi2);
settable(t3,4,phi3);
settable(t4,4,phi4);
settable(t5,1,phi5);
settable(t6,16,phi6);
settable(t7,8,phi7);
settable(t8,8,phi8);
settable(t9,8,phi9);
settable(t10,1,phi10);
settable(t11,8,phi11);
settable(t12,16,rec);
/* CHECK VALIDITY OF PARAMETER RANGES */
if( BigTC - 0.5*(ni2-1)*1/(sw2) - WFG_STOP_DELAY - POWER_DELAY
- 4.0e-6
< 0.2e-6 )
{
printf(" ni2 is too big\n");
psg_abort(1);
}
if((dm[A] == 'y' || dm[B] == 'y' ))
{
printf("incorrect dec1 decoupler flags! ");
psg_abort(1);
}
if((dm2[A] == 'y' || dm2[B] == 'y' || dm2[C] == 'y'))
{
printf("incorrect dec2 decoupler flags! Should be 'nnn' ");
psg_abort(1);
}
if( satpwr > 9 )
{
printf("SATPWR too large !!! ");
psg_abort(1);
}
if( dpwr > 48 )
{
printf("don't fry the probe, DPWR too large! ");
psg_abort(1);
}
if( dpwr2 > -16 )
{
printf("don't fry the probe, DPWR2 too large! ");
psg_abort(1);
}
if( pw > 200.0e-6 )
{
printf("dont fry the probe, pw too high ! ");
psg_abort(1);
}
if( pwN > 200.0e-6 )
{
printf("dont fry the probe, pwN too high ! ");
psg_abort(1);
}
if( pwC > 200.0e-6 )
{
printf("dont fry the probe, pwC too high ! ");
psg_abort(1);
}
if( pwcrb180 > 500.0e-6 )
{
printf("dont fry the probe, pwcrb180 too high ! ");
psg_abort(1);
}
if(dpwr3 > 51)
{
printf("dpwr3 is too high; < 52\n");
psg_abort(1);
}
if(d1 < 1)
{
printf("d1 must be > 1\n");
psg_abort(1);
}
if( gt0 > 5.0e-3 || gt1 > 5.0e-3 || gt2 > 5.0e-3 ||
gt3 > 5.0e-3 || gt4 > 5.0e-3 || gt5 > 5.0e-3 || gt6 > 5.0e-3 )
{ printf(" all values of gti must be < 5.0e-3\n");
psg_abort(1);
}
/* Phase incrementation for hypercomplex 2D data */
if (phase == 2) {
tsadd(t11,1,4);
}
if (phase2 == 2)
tsadd(t10,1,4);
/* Set up f1180 tau1 = t1 */
tau1 = d2;
tau1 = tau1 - 4.0/PI*pwco90 - POWER_DELAY - WFG_START_DELAY
- 4.0e-6 - pwca180 - WFG_STOP_DELAY - POWER_DELAY - 2.0*pwN;
if(f1180[A] == 'y') {
tau1 += ( 1.0 / (2.0*sw1) );
if(tau1 < 0.4e-6) tau1 = 4.0e-7;
}
tau1 = tau1/2.0;
/* Set up f2180 tau2 = t2 */
tau2 = d3;
if(f2180[A] == 'y') {
tau2 += ( 1.0 / (2.0*sw2) );
if(tau2 < 0.4e-6) tau2 = 4.0e-7;
}
tau2 = tau2/2.0;
/* Calculate modifications to phases for States-TPPI acquisition */
if( ix == 1) d2_init = d2 ;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if(t1_counter % 2) {
tsadd(t11,2,4);
tsadd(t12,2,4);
}
if( ix == 1) d3_init = d3 ;
t2_counter = (int) ( (d3-d3_init)*sw2 + 0.5 );
if(t2_counter % 2) {
tsadd(t10,2,4);
tsadd(t12,2,4);
}
/* BEGIN ACTUAL PULSE SEQUENCE */
status(A);
obspower(satpwr); /* Set transmitter power for 1H presaturation */
decpower(pwClvl); /* Set Dec1 power for hard 13C pulses */
dec2power(pwNlvl); /* Set Dec2 to high power */
/* Presaturation Period */
if (satmode[A] == 'y')
{
delay(2.0e-5);
rgpulse(d1,zero,2.0e-6,2.0e-6); /* presat with transmitter */
obspower(tpwr); /* Set transmitter power for hard 1H pulses */
delay(2.0e-5);
if(fscuba[0] == 'y')
{
delay(2.2e-2);
rgpulse(pw,zero,2.0e-6,0.0);
rgpulse(2.0*pw,one,2.0e-6,0.0);
rgpulse(pw,zero,2.0e-6,0.0);
delay(2.2e-2);
}
}
else
{
delay(d1);
}
obspower(tpwr); /* Set transmitter power for hard 1H pulses */
txphase(t1);
decphase(zero);
dec2phase(zero);
delay(1.0e-5);
/* Begin Pulses */
status(B);
decoffset(dof_me);
lk_hold(); lk_sampling_off();
rcvroff();
delay(20.0e-6);
/* ensure that magnetization originates on 1H and not 13C */
if(dtt_flg[A] == 'y') {
obsoffset(tof_dtt);
obspower(tpwrs);
shaped_pulse("H2Osinc",pwHs,zero,10.0e-6,0.0);
obspower(tpwr);
obsoffset(tof);
}
decrgpulse(pwC,zero,0.0,0.0);
delay(2.0e-6);
zgradpulse(gzlvl0,gt0);
delay(gstab);
rgpulse(pw,zero,0.0,0.0); /* 90 deg 1H pulse */
delay(2.0e-6);
zgradpulse(gzlvl1,gt1);
delay(gstab);
delay(taua - gt1 -gstab -2.0e-6 );
simpulse(2.0*pw,2.0*pwC,zero,zero,0.0,0.0);
txphase(one);
delay(taua - gt1 - gstab -2.0e-6);
delay(2.0e-6);
zgradpulse(gzlvl1,gt1);
delay(gstab);
rgpulse(pw,one,0.0,0.0);
/* shaped_pulse */
obspower(tpwrs);
shaped_pulse("H2Osinc",pwHs,zero,2.0e-6,0.0);
obspower(tpwr);
/* shaped_pulse */
decoffset(dof); /* jump 13C to 40 ppm */
delay(2.0e-6);
zgradpulse(gzlvl2,gt2);
delay(gstab);
decrgpulse(pwC,t1,4.0e-6,0.0); decphase(zero);
initval(1.0,v3);
decstepsize(decstep1);
dcplrphase(v3);
decpwrf(rfrb);
delay(BigTC - POWER_DELAY - WFG_START_DELAY);
decshaped_pulse(rb180.name,pwcrb180,zero,0.0,0.0);
dcplrphase(zero);
decphase(t2);
decpwrf(4095.0);
delay(BigTC - WFG_STOP_DELAY - POWER_DELAY);
decrgpulse(pwC,t2,0.0,0.0);
decphase(zero);
/* turn on 2H decoupling */
dec3phase(one);
dec3power(dpwr3);
dec3rgpulse(1/dmf3,one,4.0e-6,0.0);
dec3phase(zero);
dec3unblank();
dec3prgon(dseq3,1/dmf3,dres3);
dec3on();
/* turn on 2H decoupling */
initval(1.0,v3);
decstepsize(decstep1);
dcplrphase(v3);
decpwrf(rfrb);
delay(BigTC - POWER_DELAY - 4.0e-6 - 1/dmf3
- POWER_DELAY - PRG_START_DELAY - POWER_DELAY - WFG_START_DELAY);
decshaped_pulse(rb180.name,pwcrb180,zero,0.0,0.0);
dcplrphase(zero);
decphase(t3);
decpwrf(4095.0);
delay(BigTC - WFG_STOP_DELAY - POWER_DELAY);
decrgpulse(pwC,t3,0.0,0.0);
decpwrf(rfrb_cg); decphase(zero);
delay(BigTC/2.0 - POWER_DELAY - WFG_START_DELAY - 0.5*pwrb_cg);
decshaped_pulse(rb180_cg.name,pwrb_cg,zero,0.0,0.0);
decpwrf(rfrb);
delay(BigTC/2.0 - 0.5*pwrb_cg - WFG_STOP_DELAY - POWER_DELAY - SAPS_DELAY
- 2.0e-6 - WFG_START_DELAY);
initval(1.0,v3);
decstepsize(decstep1);
dcplrphase(v3);
decshaped_pulse(rb180.name,pwcrb180,zero,2.0e-6,0.0);
dcplrphase(zero);
decpwrf(rfrb_cg); decphase(zero);
delay(BigTC/2.0 - WFG_STOP_DELAY - SAPS_DELAY
- POWER_DELAY - WFG_START_DELAY - 0.5*pwrb_cg);
decshaped_pulse(rb180_cg.name,pwrb_cg,zero,0.0,0.0);
decpwrf(4095.0); decphase(t4);
delay(BigTC/2.0 - 0.5*pwrb_cg - WFG_STOP_DELAY - POWER_DELAY);
decrgpulse(pwC,t4,0.0,0.0);
decpwrf(rfrb_co); decphase(zero);
decshaped_pulse(rb180_co.name,pwrb_co,zero,4.0e-6,0.0); /* BS */
decpwrf(rfrb);
delay(taub - (2.0/PI)*pwC - POWER_DELAY - 4.0e-6 - WFG_START_DELAY
- pwrb_co - WFG_STOP_DELAY - 2.0e-6
- WFG_START_DELAY);
initval(1.0,v3);
decstepsize(decstep2);
dcplrphase(v3);
decshaped_pulse(rb180.name,pwcrb180,zero,2.0e-6,0.0);
dcplrphase(zero); decpwrf(rfrb_co);
decshaped_pulse(rb180_co.name,pwrb_co,zero,4.0e-6,0.0);
decphase(t5);
decpwrf(rfca90);
delay(taub - WFG_STOP_DELAY - 4.0e-6 - WFG_START_DELAY
- pwcrb180 - WFG_STOP_DELAY - POWER_DELAY
- WFG_START_DELAY - (2.0/PI)*pwca90);
decshaped_pulse(ca90.name,pwca90,t5,0.0,0.0);
decoffset(dofCO);
/* 2H decoupling off */
dec3off();
dec3prgoff();
dec3blank();
dec3rgpulse(1/dmf3,three,4.0e-6,0.0);
/* 2H decoupling off */
delay(2.0e-6);
zgradpulse(gzlvl5,gt5);
delay(gstab);
decrgpulse(pwco90,t11,4.0e-6,0.0);
if(C_flg[A] == 'n') {
decpwrf(rfca180);
delay(tau1);
decshaped_pulse(ca180.name,pwca180,zero,4.0e-6,0.0);
decpwrf(rfca90); decphase(zero);
dec2rgpulse(2.0*pwN,zero,0.0,0.0);
delay(tau1);
}
else
decrgpulse(2.0*pwco90,zero,4.0e-6,4.0e-6);
decrgpulse(pwco90,zero,0.0,0.0);
delay(2.0e-6);
zgradpulse(gzlvl6,gt6);
delay(gstab);
/* turn on 2H decoupling */
dec3phase(one);
dec3rgpulse(1/dmf3,one,4.0e-6,0.0);
dec3phase(zero);
dec3unblank();
dec3prgon(dseq3,1/dmf3,dres3);
dec3on();
/* turn on 2H decoupling */
decoffset(dof);
decpwrf(rfca90);
decshaped_pulse(ca90.name,pwca90,t6,4.0e-6,0.0);
decpwrf(rfrb_co); decphase(zero);
delay(taub - WFG_STOP_DELAY - (2.0/PI)*pwca90 - POWER_DELAY - WFG_START_DELAY
- pwrb_co - WFG_STOP_DELAY - 2.0e-6
- WFG_START_DELAY);
decshaped_pulse(rb180_co.name,pwrb_co,zero,0.0,0.0);
decpwrf(rfrb);
initval(1.0,v3);
decstepsize(decstep3);
dcplrphase(v3);
decshaped_pulse(rb180.name,pwcrb180,zero,2.0e-6,0.0);
dcplrphase(zero);
decpwrf(rfrb_co);
delay(taub - WFG_STOP_DELAY - 4.0e-6 - WFG_START_DELAY
- pwcrb180 - WFG_STOP_DELAY - POWER_DELAY - 4.0e-6
- (2.0/PI)*pwC);
decshaped_pulse(rb180_co.name,pwrb_co,zero,4.0e-6,0.0); /* BS */
decpwrf(4095.0);
decrgpulse(pwC,t7,4.0e-6,0.0);
decpwrf(rfrb_cg); decphase(zero);
delay(BigTC/2.0 - POWER_DELAY - WFG_START_DELAY - 0.5*pwrb_cg);
decshaped_pulse(rb180_cg.name,pwrb_cg,zero,0.0,0.0);
decpwrf(rfrb);
delay(BigTC/2.0 - 0.5*pwrb_cg - WFG_STOP_DELAY - POWER_DELAY - SAPS_DELAY
- 2.0e-6 - WFG_START_DELAY);
initval(1.0,v3);
decstepsize(decstep1);
dcplrphase(v3);
decshaped_pulse(rb180.name,pwcrb180,zero,2.0e-6,0.0);
dcplrphase(zero);
decpwrf(rfrb_cg); decphase(zero);
delay(BigTC/2.0 - WFG_STOP_DELAY - SAPS_DELAY
- POWER_DELAY - WFG_START_DELAY - 0.5*pwrb_cg);
decshaped_pulse(rb180_cg.name,pwrb_cg,zero,0.0,0.0);
decpwrf(4095.0); decphase(t8);
delay(BigTC/2.0 - 0.5*pwrb_cg - WFG_STOP_DELAY - POWER_DELAY);
decrgpulse(pwC,t8,0.0,0.0);
decphase(zero);
initval(1.0,v3);
decstepsize(decstep1);
dcplrphase(v3);
decpwrf(rfrb);
delay(BigTC - POWER_DELAY - WFG_START_DELAY);
decshaped_pulse(rb180.name,pwcrb180,zero,0.0,0.0);
dcplrphase(zero);
decphase(t9);
decpwrf(4095.0);
delay(BigTC - WFG_STOP_DELAY - POWER_DELAY
- PRG_STOP_DELAY - POWER_DELAY - 4.0e-6 - 1/dmf3);
/* 2H decoupling off */
dec3off();
dec3prgoff();
dec3blank();
dec3rgpulse(1/dmf3,three,4.0e-6,0.0);
lk_autotrig();
/* 2H decoupling off */
decrgpulse(pwC,t9,0.0,0.0);
decphase(zero);
delay(tau2);
rgpulse(2.0*pw,zero,0.0,0.0);
initval(1.0,v3);
decstepsize(decstep1);
dcplrphase(v3);
decpwrf(rfrb);
delay(BigTC - 2.0*pw - POWER_DELAY - WFG_START_DELAY);
decshaped_pulse(rb180.name,pwcrb180,zero,0.0,0.0);
dcplrphase(zero);
decphase(t10);
decpwrf(4095.0);
delay(BigTC - tau2 - WFG_STOP_DELAY - POWER_DELAY - 4.0e-6);
decrgpulse(pwC,t10,4.0e-6,0.0);
decoffset(dof_me);
delay(2.0e-6);
zgradpulse(gzlvl3,gt3);
delay(gstab);
lk_sample();
/* shaped_pulse */
obspower(tpwrs);
shaped_pulse("H2Osinc",pwHs,zero,2.0e-6,0.0);
obspower(tpwr);
/* shaped_pulse */
rgpulse(pw,zero,4.0e-6,0.0);
delay(2.0e-6);
zgradpulse(gzlvl4,gt4);
delay(gstab);
delay(taua - gt4 - gstab -2.0e-6
- POWER_DELAY - 2.0e-6 - WFG_START_DELAY
- pwHs - WFG_STOP_DELAY - POWER_DELAY - 2.0e-6);
/* shaped_pulse */
obspower(tpwrs);
shaped_pulse("H2Osinc",pwHs,two,2.0e-6,0.0);
obspower(tpwr);
/* shaped_pulse */
simpulse(2.0*pw,2.0*pwC,zero,zero,2.0e-6,0.0);
/* shaped_pulse */
obspower(tpwrs);
shaped_pulse("H2Osinc",pwHs,two,2.0e-6,0.0);
obspower(tpwr);
/* shaped_pulse */
delay(2.0e-6);
zgradpulse(gzlvl4,gt4);
delay(gstab);
delay(taua
- POWER_DELAY - 2.0e-6 - WFG_START_DELAY
- pwHs - WFG_STOP_DELAY - POWER_DELAY
- gt4 - gstab -2.0e-6 - 2.0*POWER_DELAY);
decpower(dpwr); /* Set power for decoupling */
dec2power(dpwr2);
/* BEGIN ACQUISITION */
lk_sample();
status(C);
setreceiver(t12);
}
pulsesequence()
{
/* DECLARE AND LOAD VARIABLES */
int t1_counter, t2_counter; /* used for states tppi in t1 & t2*/
char IPAP[MAXSTR], Hstart[MAXSTR],
f1180[MAXSTR],H2dec[MAXSTR],
shCACB_90[MAXSTR],shCACB_90r[MAXSTR],
shCACB_180[MAXSTR], shCB_180[MAXSTR], decCB[MAXSTR],
shCACB_180off[MAXSTR],
shCBIP[MAXSTR],
shCO_90[MAXSTR],
shCO_180[MAXSTR],
shCO_180off[MAXSTR];
double
tau1, /* t1 delay */
x,
TCH = getval("TCH"),
TC = getval("TC"), /* delay 1/(2JCACB) ~ 7.0ms in Ref. */
del = getval("del"), /* delay del = 1/(2JC'C) ~ 9.0ms in Ref. */
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
compC = getval("compC"), /* adjustment for C13 amplifier compression */
pwClvlF=getval("pwClvlF"), /* maximum fine power when using pwC pulses */
pwHlvl = getval("pwHlvl"),
pwH = getval("pwH"),
pwCBIP = getval("pwCBIP"),
/* 90 degree pulse at CO (174ppm) */
pwCO_90 = getval("pwCO_90"), /* 90 degree pulse length on C13 */
pwCO_90phase_roll = getval("pwCO_90phase_roll") , /* fraction of CACB pulse to compensate for phase roll */
pwrCO_90 = getval("pwrCO_90"), /*power */
pwrfCO_90 = getval("pwrfCO_90"),
/* 180 degree pulse at CO (174ppm) */
pwCO_180 = getval("pwCO_180"), /* 180 degree pulse length on C13 */
pwrCO_180 = getval("pwrCO_180"), /*power */
pwrfCO_180 = getval("pwrfCO_180"),
/* 90 degree pulse at CAB (57.7ppm) */
tofCACB = getval("tofCACB"),
pwCACB_90 = getval("pwCACB_90"),
pwCACB_90phase_roll = getval("pwCACB_90phase_roll") , /* fraction of CACB pulse to compensate for phase roll */
/* 90 degree pulse length on C13 */
pwrCACB_90 = getval("pwrCACB_90"), /*power */
pwrfCACB_90 = getval("pwrfCACB_90"),
/* 180 degree pulse at CA (57.7ppm) */
pwCACB_180 = getval("pwCACB_180"), /* 180 degree pulse length on C13 */
pwrCACB_180 = getval("pwrCACB_180"), /*power */
pwrfCACB_180 = getval("pwrfCACB_180"),
pwCB_180 = getval("pwCB_180"), /* 180 degree pulse length on C13 */
pwrCB_180 = getval("pwrCB_180"),
sw1 = getval("sw1"),
sw2 = getval("sw2"),
gt1 = getval("gt1"),
gzlvl1 = getval("gzlvl1"),
gt2 = getval("gt2"),
gzlvl2 = getval("gzlvl2"),
gt3 = getval("gt3"),
gzlvl3 = getval("gzlvl3"),
gstab = getval("gstab");
getstr("IPAP",IPAP);
getstr("H2dec",H2dec);
getstr("shCBIP",shCBIP);
getstr("f1180",f1180);
getstr("shCACB_90",shCACB_90); getstr("shCACB_90r",shCACB_90r);
getstr("shCACB_180",shCACB_180); getstr("shCACB_180off",shCACB_180off);
getstr("shCB_180",shCB_180); getstr("decCB",decCB);
getstr("shCO_90",shCO_90);
getstr("shCO_180",shCO_180); getstr("shCO_180off",shCO_180off);
getstr("Hstart",Hstart);
/* LOAD PHASE TABLE */
settable(t1,4,phi1);
settable(t2,4,phi2);
settable(t3,4,phi3);
settable(t4,4,phi4);
settable(t5,4,phi5);
settable(t12,4,rec);
/* INITIALIZE VARIABLES */
if( (IPAP[A] != 'i') && (IPAP[A] != 'a')&& (IPAP[A] != 't'))
{ text_error("IPAP flag either i or a, exiting "); psg_abort(1); }
if( (Hstart[A]=='y') && ((dmm[A]!='c' || dm[A]=='y')) )
{
text_error("Incorrect combination of dm, dmm and Hstart. ");
psg_abort(1);};
x=0.0;
if(decCB[A]=='y'){x=1.0;}
if(ni/sw1 > TC-2.0*pwCB_180*x) {
text_error("too many increments in CAB t1 evolution %d\n",(int)( (TC-2.0*pwCB_180*x)*sw1 +0.5));
psg_abort(1);};
/* PHASES AND INCREMENTED TIMES */
/* Phase incrementation for hypercomplex 2D data, States-Haberkorn element */
if (phase1 == 2) tsadd(t1,1,4);
tau1 = d2;
if(f1180[A]=='y') {tau1+=0.5/sw1;}
tau1 = tau1/2.0;
/* Calculate modifications to phases for States-TPPI acquisition */
if(IPAP[A]=='a'){tsadd(t4,1,4);};
if( ix == 1) d2_init = d2;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if(t1_counter % 2)
{ tsadd(t1,2,4); tsadd(t12,2,4); }
/* BEGIN PULSE SEQUENCE */
status(A);
delay(10.0e-6);
obspower(pwClvl);
obspwrf(4095.0);
dec2power(dpwr2); dec2pwrf(4095.0);
obsoffset(tofCACB);
delay(d1);
/* option to start from H magnetization */
if(Hstart[A]=='y')
{
decpower(pwHlvl); decpwrf(4095.0);
decrgpulse(pwH, zero, 0.0, 0.0);
delay(TCH);
simpulse(2.0*pwC,2.0*pwH, zero,zero, 0.0, 0.0);
delay(TCH);
decrgpulse(pwH, one, 0.0, 0.0);
zgradpulse(gzlvl2,gt2);
delay(gstab);
rgpulse(pwC, two, 0.0, 0.0);
delay(TCH);
simpulse(2.0*pwC,2.0*pwH, zero,zero, 0.0, 0.0);
delay(TCH);
rgpulse(pwC, one, 0.0, 0.0);
zgradpulse(gzlvl3,gt3);
delay(gstab*2.0);
decpower(dpwr); decpwrf(4095.0);
}
if (H2dec[A] == 'y') lk_hold();
status(B);
/* CACO experiment */
/************optional deuterium decoupling**************************/
if(H2dec[A] == 'y'){ dec3unblank();
if(1.0/dmf3>900.0e-6) {
dec3power(dpwr3+6.0);
dec3rgpulse(0.5/dmf3, one, 1.0e-6, 0.0e-6);
dec3power(dpwr3);
}
else dec3rgpulse(1.0/dmf3, one, 1.0e-6,0.0e-6);
dec3phase(zero); setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
}
/**************************************/
/* begin CA evolution and transfer to CO */
obspwrf(pwrfCACB_90); obspower(pwrCACB_90);
shapedpulse(shCACB_90,pwCACB_90,t1,0.0,0.0);
obspwrf(4095.0); obspower(pwClvl);
delay(10.0e-6);
shapedpulse(shCBIP,pwCBIP,zero,0.0,0.0);
delay(10.0e-6);
if(decCB[A]=='y') {
delay( (TC/2.0-tau1 + 2.0*pwCACB_90phase_roll*pwCACB_90)*0.5 -pwCB_180*0.5);
obspower(pwrCB_180);
shapedpulse(shCB_180,pwCB_180,zero,0.0,0.0);
delay( (TC/2.0-tau1 + 2.0*pwCACB_90phase_roll*pwCACB_90)*0.5 -pwCB_180*0.5);
}
else delay(TC/2.0-tau1 + 2.0*pwCACB_90phase_roll*pwCACB_90);
obspower(pwClvl);
shapedpulse(shCBIP,pwCBIP,zero,0.0,0.0);
if(decCB[A]=='y') {
delay((TC/2.0+tau1)*0.5 -pwCB_180*0.5);
obspower(pwrCB_180);
shapedpulse(shCB_180,pwCB_180,zero,0.0,0.0);
delay((TC/2.0+tau1)*0.5 -pwCB_180*0.5);
}
else delay(TC/2.0+tau1);
obspower(pwrCACB_90);
shapedpulse(shCACB_90r,pwCACB_90,one,0.0,0.0);
/*************************************************************/
if(H2dec[A] == 'y') {
setstatus(DEC3ch, FALSE, 'w', FALSE, dmf3);
if(1.0/dmf3>900.0e-6) {
dec3power(dpwr3+6.0);
dec3rgpulse(0.5/dmf3, three, 1.0e-6, 0.0e-6);
dec3power(dpwr3);
}
else dec3rgpulse(1.0/dmf3, three, 1.0e-6, 0.0e-6); dec3blank();
}
/*************************************************************/
/* CAzCOz */
delay(10e-6);
obsoffset(tof);
delay(10e-6);
zgradpulse(gzlvl1,gt1);
delay(gstab);
status(C);
/* CAzCOz -> CO or CACO */
obspwrf(pwrfCO_90); obspower(pwrCO_90);
shapedpulse(shCO_90,pwCO_90,t4,0.0,0.0);
/* ghost 180 on CA*/
if(IPAP[A]=='i') {
obspwrf(pwClvlF); obspower(pwClvl);
delay(10.0e-6);
shapedpulse(shCBIP,pwCBIP,zero,0.0,0.0);
delay(10.0e-6);
delay(del/2.0 + pwCO_90phase_roll*pwCO_90);
obspwrf(pwrfCACB_180); obspower(pwrCACB_180);
delay(10.0e-6);
shapedpulse(shCACB_180off,pwCACB_180,zero,0.0,0.0);
obspwrf(pwClvlF); obspower(pwClvl);
delay(10.0e-6);
shapedpulse(shCBIP,pwCBIP,zero,0.0,0.0);
obspwrf(pwrfCACB_180); obspower(pwrCACB_180);
delay(10.0e-6);
shapedpulse(shCACB_180off,pwCACB_180,zero,0.0,0.0);
delay(10.0e-6);
delay(del/2.0 );
}
/***>>>>>>>>>>>**TEST*********/
if(IPAP[A]=='t') {
obspwrf(pwrfCACB_180); obspower(pwrCACB_180);
delay(10.0e-6);
shapedpulse(shCACB_180off,pwCACB_180,zero,0.0,0.0);
delay(10.0e-6);
obspwrf(pwrfCO_180); obspower(pwrCO_180);
delay(del/2.0);
shapedpulse(shCO_180,pwCO_180,zero,0.0,0.0);
obspwrf(pwrfCACB_180); obspower(pwrCACB_180);
delay(10.0e-6);
shapedpulse(shCACB_180off,pwCACB_180,zero,0.0,0.0);
delay(10.0e-6);
obspwrf(pwrfCO_90); obspower(pwrCO_90);
delay(del/2.0);
}
/********<<<<<<<<<<<<<**TEST*********/
if(IPAP[A]=='a') {
obspwrf(pwClvlF); obspower(pwClvl);
delay(10.0e-6);
shapedpulse(shCBIP,pwCBIP,zero,0.0,0.0);
delay(10.0e-6);
delay(del/4.0 + pwCO_90phase_roll*pwCO_90);
obspwrf(pwrfCACB_180); obspower(pwrCACB_180);
delay(10.0e-6);
shapedpulse(shCACB_180off,pwCACB_180,zero,0.0,0.0);
obspwrf(pwClvlF); obspower(pwClvl);
delay(10.0e-6);
delay(del/4.0 );
shapedpulse(shCBIP,pwCBIP,zero,0.0,0.0);
delay(del/4.0);
obspwrf(pwrfCACB_180); obspower(pwrCACB_180);
delay(10.0e-6);
shapedpulse(shCACB_180off,pwCACB_180,zero,0.0,0.0);
delay(10.0e-6);
delay(del/4.0 );
}
if (H2dec[A]=='y') lk_sample();
status(D);
setreceiver(t12);
}
pulsesequence()
{
char sel_flg[MAXSTR],
autocal[MAXSTR],
glyshp[MAXSTR];
int icosel, t1_counter, ni = getval("ni");
double
d2_init=0.0,
tau1, tau2,
tau3,
glypwr,glypwrf, /* Power levels for Cgly selective 90 */
pwgly, /* Pulse width for Cgly selective 90 */
waltzB1 = getval("waltzB1"), /* 1H decoupling strength (in Hz) */
timeTN = getval("timeTN"), /* constant time for 15N evolution */
tauCaCb = getval("tauCaCb"),
tauNCa = getval("tauNCa"),
tauNCo = getval("tauNCo"),
tauCaCo = getval("tauCaCo"),
compH = getval("compH"), /* adjustment for H1 amplifier compression */
tpwrs, /* power for the pwHs ("H2Osinc") pulse */
bw,ppm,
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
compC = getval("compC"), /* amplifier compression for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
pwNlvl = getval("pwNlvl"), /* power for N15 pulses */
pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */
dpwr2 = getval("dpwr2"), /* power for N15 decoupling */
pwCa90, /* length of square 90 on Ca */
pwCa180,
pwCab90,
pwCab180,
phshift, /* phase shift induced on Ca by 180 on CO in middle of t1 */
pwCO180, /* length of 180 on CO */
pwS = getval("pwS"), /* used to change 180 on CO in t1 for 1D calibrations */
pwZ, /* the largest of pwCO180 and 2.0*pwN */
pwZ1, /* the largest of pwCO180 and 2.0*pwN for 1D experiments */
sw1 = getval("sw1"),
swCb = getval("swCb"),
swCa = getval("swCa"),
swN = getval("swN"),
swTilt, /* This is the sweep width of the tilt vector */
cos_N, cos_Ca, cos_Cb,
angle_N, angle_Ca, angle_Cb, /* angle_N is calculated automatically */
gstab = getval("gstab"),
gt0 = getval("gt0"), gzlvl0 = getval("gzlvl0"),
gt1 = getval("gt1"), gzlvl1 = getval("gzlvl1"),
gzlvl2 = getval("gzlvl2"),
gt3 = getval("gt3"), gzlvl3 = getval("gzlvl3"),
gt4 = getval("gt4"), gzlvl4 = getval("gzlvl4"),
gt5 = getval("gt5"), gzlvl5 = getval("gzlvl5"),
gt6 = getval("gt6"), gzlvl6 = getval("gzlvl6"),
gt7 = getval("gt7"), gzlvl7 = getval("gzlvl7"),
gt10= getval("gt10"), gzlvl10= getval("gzlvl10"),
gt11= getval("gt11"), gzlvl11= getval("gzlvl11"),
gt12= getval("gt12"), gzlvl12= getval("gzlvl12");
angle_N = 0;
glypwr = getval("glypwr");
pwgly = getval("pwgly");
tau1 = 0;
tau2 = 0;
tau3 = 0;
cos_N = 0;
cos_Cb = 0;
cos_Ca = 0;
getstr("autocal", autocal);
getstr("glyshp", glyshp);
getstr("sel_flg",sel_flg);
pwHs = getval("pwHs"); /* H1 90 degree pulse length at tpwrs */
/* LOAD PHASE TABLE */
settable(t2,1,phy);
settable(t3,2,phi3); settable(t4,1,phx); settable(t5,4,phi5);
settable(t8,1,phy); settable(t9,8,phi9); settable(t10,1,phx);
settable(t11,1,phy); settable(t12,4,rec);
/* INITIALIZE VARIABLES */
kappa = 5.4e-3; lambda = 2.4e-3;
/* selective H20 one-lobe sinc pulse */
tpwrs = tpwr - 20.0*log10(pwHs/(compH*pw*1.69)); /*needs 1.69 times more*/
tpwrs = (int) (tpwrs); /*power than a square pulse */
pwHs = 1.7e-3*500.0/sfrq;
widthHd = 2.861*(waltzB1/sfrq); /* bandwidth of H1 WALTZ16 decoupling in ppm */
pwHd = h1dec90pw("WALTZ16", widthHd, 0.0); /* H1 90 length for WALTZ16 */
/* get calculated pulse lengths of shaped C13 pulses */
pwCa90 = c13pulsepw("ca", "co", "square", 90.0);
pwCa180 = c13pulsepw("ca", "co", "square", 180.0);
pwCO180 = c13pulsepw("co", "cab", "sinc", 180.0);
pwCab90 = c13pulsepw("cab","co", "square", 90.0);
pwCab180= c13pulsepw("cab","co", "square", 180.0);
/* the 180 pulse on CO at the middle of t1 */
if (pwCO180 > 2.0*pwN) pwZ = pwCO180; else pwZ = 2.0*pwN;
if ((pwS==0.0) && (pwCO180>2.0*pwN)) pwZ1=pwCO180-2.0*pwN; else pwZ1=0.0;
if ( ni > 1 ) pwS = 180.0;
if ( pwS > 0 ) phshift = 320.0;
else phshift = 0.0;
/* CHECK VALIDITY OF PARAMETER RANGES */
if ( dm[A] == 'y' || dm[B] == 'y' || dm[C] == 'y' )
{ printf("incorrect dec1 decoupler flags! Should be 'nnn' "); psg_abort(1);}
if ( dm2[A] == 'y' || dm2[B] == 'y' )
{ printf("incorrect dec2 decoupler flags! Should be 'nny' "); psg_abort(1);}
if ( dm3[A] == 'y' || dm3[C] == 'y' )
{ printf("incorrect dec3 decoupler flags! Should be 'nyn' or 'nnn' ");
psg_abort(1);}
if ( dpwr2 > 46 )
{ printf("dpwr2 too large! recheck value "); psg_abort(1);}
if ( pw > 20.0e-6 )
{ printf(" pw too long ! recheck value "); psg_abort(1);}
if ( pwN > 100.0e-6 )
{ printf(" pwN too long! recheck value "); psg_abort(1);}
/* PHASES AND INCREMENTED TIMES */
/* Set up angles and phases */
angle_Cb=getval("angle_Cb"); cos_Cb=cos(PI*angle_Cb/180.0);
angle_Ca=getval("angle_Ca"); cos_Ca=cos(PI*angle_Ca/180.0);
if ( (angle_Cb < 0) || (angle_Cb > 90) )
{ printf ("angle_Cb must be between 0 and 90 degree.\n"); psg_abort(1); }
if ( (angle_Ca < 0) || (angle_Ca > 90) )
{ printf ("angle_Ca must be between 0 and 90 degree.\n"); psg_abort(1); }
if ( 1.0 < (cos_Cb*cos_Cb + cos_Ca*cos_Ca) )
{
printf ("Impossible angles.\n"); psg_abort(1);
}
else
{
cos_N=sqrt(1.0- (cos_Cb*cos_Cb + cos_Ca*cos_Ca));
angle_N = 180.0*acos(cos_N)/PI;
}
swTilt=swCb*cos_Cb + swCa*cos_Ca + swN*cos_N;
if (ix ==1)
{
printf("\n\nn\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n");
printf ("Maximum Sweep Width: \t\t %f Hz\n", swTilt);
printf ("Angle_Cb:\t%6.2f\n", angle_Cb);
printf ("Angle_Ca:\t%6.2f\n", angle_Ca);
printf ("Angle_N :\t%6.2f\n", angle_N );
}
/* Set up hyper complex */
/* sw1 is used as symbolic index */
if ( sw1 < 1000 ) { printf ("Please set sw1 to some value larger than 1000.\n"); psg_abort(1); }
if (ix == 1) d2_init = d2;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if (t1_counter % 2) { tsadd(t8,2,4); tsadd(t12,2,4); }
if (phase1 == 1) { ;} /* CC */
else if (phase1 == 2) { tsadd(t3,3,4); tsadd(t2,3,4);} /* SC */
else if (phase1 == 3) { tsadd(t5,1,4); } /* CS */
else if (phase1 == 4) { tsadd(t3,3,4); tsadd(t2,3,4); tsadd(t5,1,4);} /* SS */
else { printf ("phase1 can only be 1,2,3,4. \n"); psg_abort(1); }
if (phase2 == 2) { tsadd(t10,2,4); icosel = +1; } /* N */
else icosel = -1;
tau1 = 1.0*t1_counter*cos_Cb/swTilt;
tau2 = 1.0*t1_counter*cos_Ca/swTilt;
tau3 = 1.0*t1_counter*cos_N/swTilt;
tau1 = tau1/2.0; tau2 = tau2/2.0; tau3 = tau3/2.0;
/* CHECK VALIDITY OF PARAMETER RANGES */
if (0.5*ni*(cos_N/swTilt) > timeTN - WFG3_START_DELAY)
{ printf(" ni is too big. Make ni equal to %d or less.\n",
((int)((timeTN - WFG3_START_DELAY)*2.0*swTilt/cos_N))); psg_abort(1);}
/* BEGIN PULSE SEQUENCE */
status(A);
delay(d1);
if ( dm3[B] == 'y' ) lk_hold();
rcvroff();
obsoffset(tof); obspower(tpwr); obspwrf(4095.0);
set_c13offset("cab"); decpower(pwClvl); decpwrf(4095.0);
dec2power(pwNlvl);
txphase(zero); delay(1.0e-5);
decrgpulse(pwC, zero, 0.0, 0.0);
zgradpulse(gzlvl0, gt0);
delay(gstab);
decrgpulse(pwC, one, 0.0, 0.0);
zgradpulse(0.7*gzlvl0, gt0);
delay(gstab);
txphase(one); delay(1.0e-5);
shiftedpulse("sinc", pwHs, 90.0, 0.0, one, 2.0e-6, 0.0);
txphase(zero); decphase(zero); dec2phase(zero);
delay(2.0e-6);
/* pulse sequence starts */
rgpulse(pw,zero,0.0,0.0); /* 1H pulse excitation */
dec2phase(zero);
zgradpulse(gzlvl3, gt3);
delay(lambda - gt3);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
if (sel_flg[A] == 'n') txphase(three);
else txphase(one);
zgradpulse(gzlvl3, gt3);
delay(lambda - gt3);
if (sel_flg[A] == 'n')
{
rgpulse(pw, three, 0.0, 0.0);
txphase(zero);
zgradpulse(gzlvl4, gt4); /* Crush gradient G4 */
delay(gstab);
/* Begin of N to Ca transfer */
dec2rgpulse(pwN, one, 0.0, 0.0);
decphase(zero); dec2phase(zero);
delay(tauNCo - pwCO180/2 - 2.0e-6 - WFG3_START_DELAY);
}
else /* active suppresion */
{
rgpulse(pw,one,2.0e-6,0.0);
initval(1.0,v6); dec2stepsize(45.0); dcplr2phase(v6);
zgradpulse(gzlvl4, gt4); /* Crush gradient G4 */
delay(gstab);
/* Begin of N to Ca transfer */
dec2rgpulse(pwN,one,0.0,0.0);
dcplr2phase(zero); /* SAPS_DELAY */
delay(1.34e-3 - SAPS_DELAY - 2.0*pw);
rgpulse(pw,one,0.0,0.0);
rgpulse(2.0*pw,zero,0.0,0.0);
rgpulse(pw,one,0.0,0.0);
delay(tauNCo - pwCO180/2 - 1.34e-3 - 2.0*pw - WFG3_START_DELAY);
}
/* Begin transfer from HzNz to N(i)zC'(i-1)zCa(i)zCa(i-1)z */
c13pulse("co", "cab", "sinc", 180.0, zero, 2.0e-6, 0.0);
delay(tauNCa - tauNCo - pwCO180/2 - WFG3_START_DELAY -
WFG3_STOP_DELAY - 2.0e-6);
/* WFG3_START_DELAY */
sim3_c13pulse("", "cab", "co", "square", "", 0.0, 180.0, 2.0*pwN,
zero, zero, zero, 2.0e-6, 2.0e-6);
delay(tauNCa - 2.0e-6 - WFG3_STOP_DELAY);
dec2rgpulse(pwN, zero, 0.0, 0.0);
/* End transfer from HzNz to N(i)zC'(i-1)zCa(i)zCa(i-1)z */
zgradpulse(gzlvl5, gt5);
delay(gstab);
/* Begin removal of Ca(i-1) */
c13pulse("co", "cab", "sinc", 90.0, zero, 2.0e-6, 2.0e-6);
zgradpulse(gzlvl6, gt6);
delay(tauCaCo - gt6 - pwCab180 - pwCO180/2 - 6.0e-6);
c13pulse("cab","co", "square", 180.0, zero, 2.0e-6, 2.0e-6);
c13pulse("co","cab", "sinc", 180.0, zero, 2.0e-6, 2.0e-6);
zgradpulse(gzlvl6, gt6);
delay(tauCaCo - gt6 - pwCab180 - pwCO180/2 - 6.0e-6);
c13pulse("cab","co", "square", 180.0, zero, 2.0e-6, 2.0e-6);
c13pulse("co", "cab", "sinc", 90.0, one, 2.0e-6, 2.0e-6);
/* End removal of Ca(i-1) */
/* xx Selective glycine pulse xx */
set_c13offset("gly");
setautocal();
if (autocal[A] == 'y')
{
if(FIRST_FID)
{
ppm = getval("dfrq"); bw=9*ppm;
gly90 = pbox_make("gly90","eburp1",bw,0.0,compC*pwC,pwClvl);
/* Gly selective 90 with null at 50ppm */
}
pwgly=gly90.pw; glypwr=gly90.pwr; glypwrf=gly90.pwrf;
decpwrf(glypwrf);
decpower(glypwr);
decshaped_pulse("gly90",pwgly,zero,2.0e-6,0.0);
}
else
{
decpwrf(4095.0);
decpower(glypwr);
decshaped_pulse(glyshp,pwgly,zero,2.0e-6,0.0);
}
/* xx End of glycine selecton xx */
zgradpulse(gzlvl7, gt7);
set_c13offset("cab");
delay(gstab);
decphase(t3);
if ( dm3[B] == 'y' ) /* begins optional 2H decoupling */
{
dec3unblank();
dec3rgpulse(1/dmf3,one,10.0e-6,2.0e-6);
dec3unblank();
dec3phase(zero);
delay(2.0e-6);
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
}
/* ========== Ca to Cb transfer =========== */
c13pulse("cab", "co", "square", 90.0, t3, 2.0e-6, 2.0e-6);
decphase(zero);
delay(tauCaCb - 4.0e-6);
c13pulse("cab", "co", "square", 180.0, zero, 2.0e-6, 2.0e-6);
decphase(t2);
delay(tauCaCb - 4.0e-6 );
/* xxxxxxxxxxxxxxxxxxxxxx 13Cb EVOLUTION xxxxxxxxxxxxxxxxxx */
c13pulse("cab", "co", "square", 90.0, t2, 2.0e-6, 0.0); /* pwCa90 */
decphase(zero);
if ((ni>1.0) && (tau1>0.0))
{
if (tau1 - 2.0*pwCab90/PI - WFG_START_DELAY - pwN - 2.0e-6
- PWRF_DELAY - POWER_DELAY > 0.0)
{
delay(tau1 - 2.0*pwCab90/PI - pwN - 2.0e-6 );
dec2rgpulse(2.0*pwN, zero, 2.0e-6, 0.0);
delay(tau1 - 2.0*pwCab90/PI - pwN - WFG_START_DELAY
- 2.0e-6 - PWRF_DELAY - POWER_DELAY);
}
else
{
tsadd(t12,2,4);
delay(2.0*tau1);
delay(10.0e-6); /* WFG_START_DELAY */
sim3_c13pulse("", "cab", "co", "square", "", 0.0, 180.0, 2.0*pwN,
zero, zero, zero, 2.0e-6, 0.0);
delay(10.0e-6);
}
}
else
{
tsadd(t12,2,4);
delay(10.0e-6); /* WFG_START_DELAY */
sim3_c13pulse("", "cab", "co", "square", "", 0.0, 180.0, 2.0*pwN,
zero, zero, zero, 2.0e-6, 0.0);
delay(10.0e-6);
}
decphase(one);
c13pulse("cab", "co", "square", 90.0, one, 2.0e-6, 0.0); /* pwCa90 */
/* xxxxxxxxxxx End of 13Cb EVOLUTION - Start 13Ca EVOLUTION xxxxxxxxxxxx */
decphase(zero);
delay(tau2);
sim3_c13pulse("", "co", "cab", "sinc", "", 0.0, 180.0, 2.0*pwN,
zero, zero, zero, 2.0e-6, 0.0);
decphase(zero);
delay(tauCaCb - 2*pwN - pwCab180/2 - WFG2_START_DELAY - 2.0*PWRF_DELAY -
2.0*POWER_DELAY - WFG2_STOP_DELAY - 4.0e-6 );
c13pulse("cab", "co", "square", 180.0, zero, 2.0e-6, 0.0);
delay(tauCaCb- tau2 - pwCO180 - pwCab180/2 - WFG2_START_DELAY - 2.0*PWRF_DELAY
-2.0*POWER_DELAY - WFG2_STOP_DELAY - 4.0e-6);
c13pulse("co", "cab", "sinc", 180.0, zero, 2.0e-6, 0.0);
decphase(t5);
c13pulse("cab", "co", "square", 90.0, t5, 2.0e-6, 0.0);
/* xxxxxxxxxxxxxxxxxxx End of 13Ca EVOLUTION xxxxxxxxxxxxxxxxxx */
if ( dm3[B] == 'y' ) /* turns off 2H decoupling */
{
dec3rgpulse(1/dmf3,three,2.0e-6,2.0e-6);
dec3blank();
setstatus(DEC3ch, FALSE, 'c', FALSE, dmf3);
dec3blank();
}
/* xxxxxxxxxxxxxxxxxxxx N15 EVOLUTION & SE TRAIN xxxxxxxxxxxxxxxxxxxxxxx */
dcplrphase(zero); dec2phase(t8);
zgradpulse(gzlvl10, gt10);
delay(gstab);
dec2rgpulse(pwN, t8, 2.0e-6, 0.0);
c13pulse("co", "cab", "sinc", 180.0, zero, 2.0e-6, 0.0); /*pwCO180*/
decphase(zero); dec2phase(t9);
delay(timeTN - pwCO180 - WFG3_START_DELAY - tau3 - 4.0e-6);
/* WFG3_START_DELAY */
sim3_c13pulse("", "cab", "co", "square", "", 0.0, 180.0, 2.0*pwN,
zero, zero, t9, 2.0e-6, 2.0e-6);
c13pulse("co", "cab", "sinc", 180.0, zero, 2.0e-6, 0.0); /*pwCO180*/
dec2phase(t10);
txphase(t4);
delay(timeTN - pwCO180 + tau3 - 500.0e-6 - gt1 - 2.0*GRADIENT_DELAY-
WFG_START_DELAY - WFG_STOP_DELAY );
delay(0.2e-6);
zgradpulse(gzlvl1, gt1);
delay(gstab);
sim3pulse(pw, 0.0, pwN, t4, zero, t10, 0.0, 0.0);
txphase(zero); dec2phase(zero);
zgradpulse(gzlvl11, gt11);
delay(lambda - 1.3*pwN - gt11);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl11, gt11); txphase(one);
dec2phase(t11);
delay(lambda - 1.3*pwN - gt11);
sim3pulse(pw, 0.0, pwN, one, zero, t11, 0.0, 0.0);
txphase(zero); dec2phase(zero);
zgradpulse(gzlvl12, gt12);
delay(lambda - 1.3*pwN - gt12);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
dec2phase(zero);
zgradpulse(gzlvl12, gt12);
delay(lambda - 1.3*pwN - gt12);
sim3pulse(pw, 0.0, pwN, zero, zero, zero, 0.0, 0.0);
delay((gt1/10.0) + 1.0e-4 + 2.0*GRADIENT_DELAY + POWER_DELAY);
rgpulse(2.0*pw, zero, 0.0, 0.0);
dec2power(dpwr2); /* POWER_DELAY */
zgradpulse(icosel*gzlvl2, gt1/10.0); /* 2.0*GRADIENT_DELAY */
statusdelay(C, 1.0e-4 );
setreceiver(t12);
if (dm3[B]=='y') lk_sample();
}
pulsesequence()
{
/* DECLARE VARIABLES */
char fsat[MAXSTR],
fscuba[MAXSTR],
f1180[MAXSTR], /* Flag to start t1 @ halfdwell */
codecseq[MAXSTR],
ddseq[MAXSTR],
shca180[MAXSTR],
shca90[MAXSTR];
int phase, ni,
t1_counter, /* used for states tppi in t1 */
tau2;
double tau1, /* t1 delay */
taua, /* ~ 1/4JCH = 1.7 ms */
taub, /* ~ 1/2JCH for AX spin systems */
taud, /* ~ 1/4JCD 12.5 ms for AX spin system */
TC, /* carbon constant time period 1/2JCC */
pwc, /* 90 c pulse at dhpwr */
tsatpwr, /* low level 1H trans.power for presat */
dhpwr, /* power level for high power 13C pulses on dec1 */
sw1, /* sweep width in f1 */
time_T2, /* total relaxation time for T2 measurement */
pwcodec, /* pw90 for C' decoupling */
dressed, /* = 2 for seduce-1 decoupling */
dpwrsed,
pwd, /* pulse width for D decoupling at dpwr3_D */
dresD,
dpwr3_D,
lk_wait, /* delay for lk receiver recovery */
pwd1, /* pulse width for D +/- pulses at dpwr3 */
d_ca180,
pwca180,
pwca90, /* ca selective pulse at 57.5 ppm */
d_ca90, /* power level for pwca90 */
dpwr3_sl, /* D power level for spin locking */
pwd_sl, /* pw for D at dpwr3_sl */
gt1,
gt2,
gt3,
gt4,
gt5,
gt6,
gt7,
gt8,
gstab=getval("gstab"),
gzlvl1,
gzlvl2,
gzlvl3,
gzlvl4,
gzlvl5,
gzlvl6,
gzlvl7,
gzlvl8;
/* variables commented out are already defined by the system */
/* LOAD VARIABLES */
getstr("fsat",fsat);
getstr("f1180",f1180);
getstr("fscuba",fscuba);
getstr("codecseq",codecseq);
getstr("ddseq",ddseq);
getstr("shca180",shca180);
getstr("shca90",shca90);
taua = getval("taua");
taub = getval("taub");
taud = getval("taud");
TC = getval("TC");
pwc = getval("pwc");
tpwr = getval("tpwr");
tsatpwr = getval("tsatpwr");
dhpwr = getval("dhpwr");
dpwr = getval("dpwr");
phase = (int) ( getval("phase") + 0.5);
sw1 = getval("sw1");
ni = getval("ni");
pwcodec = getval("pwcodec");
dressed = getval("dressed");
dpwrsed = getval("dpwrsed");
pwd = getval("pwd");
dresD = getval("dresD");
dpwr3_D = getval("dpwr3_D");
lk_wait = getval("lk_wait");
pwd1 = getval("pwd1");
d_ca180 = getval("d_ca180");
pwca180 = getval("pwca180");
pwca90 = getval("pwca90");
d_ca90 = getval("d_ca90");
dpwr3_sl = getval("dpwr3_sl");
pwd_sl = getval("pwd_sl");
gt1 = getval("gt1");
gt2 = getval("gt2");
gt3 = getval("gt3");
gt4 = getval("gt4");
gt5 = getval("gt5");
gt6 = getval("gt6");
gt7 = getval("gt7");
gt8 = getval("gt8");
gzlvl1 = getval("gzlvl1");
gzlvl2 = getval("gzlvl2");
gzlvl3 = getval("gzlvl3");
gzlvl4 = getval("gzlvl4");
gzlvl5 = getval("gzlvl5");
gzlvl6 = getval("gzlvl6");
gzlvl7 = getval("gzlvl7");
gzlvl8 = getval("gzlvl8");
/* LOAD PHASE TABLE */
settable(t1,16,phi1);
settable(t2,2,phi2);
settable(t3,16,phi3);
settable(t4,4,phi4);
settable(t6,4,phi6);
settable(t7,8,phi7);
settable(t5,16,rec_d);
/* CHECK VALIDITY OF PARAMETER RANGES */
if( TC - 0.50*(ni-1)*1/(sw1) - WFG_STOP_DELAY
- gt6 - 102e-6 - POWER_DELAY
- PRG_START_DELAY - POWER_DELAY
- 4.0e-6 - pwd1 - POWER_DELAY
- PRG_START_DELAY - PRG_STOP_DELAY
- 2.0e-6 - POWER_DELAY - 2.0e-6
< 0.2e-6 )
{
printf(" ni is too big\n");
psg_abort(1);
}
if((dm[A] == 'y' || dm[B] == 'y' || dm[C] == 'y' ))
{
printf("incorrect dec1 decoupler flags! ");
psg_abort(1);
}
if((dm2[A] == 'y' || dm2[B] == 'y' || dm2[C] == 'y' || dm2[D] == 'y'))
{
printf("incorrect dec2 decoupler flags! ");
psg_abort(1);
}
if( tsatpwr > 6 )
{
printf("TSATPWR too large !!! ");
psg_abort(1);
}
if( dpwr > 48 )
{
printf("don't fry the probe, DPWR too large! ");
psg_abort(1);
}
if( dpwr2 > 49 )
{
printf("don't fry the probe, DPWR2 too large! ");
psg_abort(1);
}
if( dhpwr > 63 )
{
printf("don't fry the probe, DHPWR too large! ");
psg_abort(1);
}
if( pw > 200.0e-6 )
{
printf("dont fry the probe, pw too high ! ");
psg_abort(1);
}
if(gt1 > 15e-3 || gt2 > 15e-3 || gt3 > 15e-3 ||
gt4 > 15e-3 || gt5 > 15e-3 || gt6 > 15e-3 || gt7 > 15e-3
|| gt8 > 15e-3)
{
printf("gradients on for too long. Must be < 15e-3 \n");
psg_abort(1);
}
if(dpwr3_D > 54)
{
printf("D decoupling power is too high\n");
psg_abort(1);
}
if(lk_wait > .015 )
{
printf("lk_wait delay may be too long\n");
psg_abort(1);
}
/* change back to 48 */
if(dpwr3_sl > 53) {
printf("dpwr3_sl is too large; must be less than 53\n");
psg_abort(1);
}
/* change back to 250 */
if(pwd_sl < 170.0e-6) {
printf("pwd_sl is too large; Must be larger than 170 us\n");
psg_abort(1);
}
/* Calculation of IzCzDz relaxation delay */
tau2 = (int) (d3+0.1);
time_T2 = z_array[tau2];
if(time_T2 > 0.030) {
printf("time_T2 is too long; Must be less than 30 ms\n");
psg_abort(1);
}
/* Phase incrementation for hypercomplex 2D data */
if (phase == 2) {
tsadd(t7,1,4);
}
/* Set up f1180 tau1 = t1 */
tau1 = d2;
if(f1180[A] == 'y') {
tau1 += ( 1.0 / (2.0*sw1) );
if(tau1 < 0.4e-6) tau1 = 0.4e-6;
}
tau1 = tau1/2.0;
/* Calculate modifications to phases for States-TPPI acquisition */
if( ix == 1) d2_init = d2 ;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if(t1_counter % 2) {
tsadd(t7,2,4);
tsadd(t5,2,4);
}
/* BEGIN ACTUAL PULSE SEQUENCE */
status(A);
decoffset(dof);
obspower(tsatpwr); /* Set transmitter power for 1H presaturation */
decpower(dhpwr); /* Set Dec1 power for hard 13C pulses */
dec2power(dpwr2); /* Set Dec2 power for 15N decoupling */
/* Presaturation Period */
status(B);
if (fsat[0] == 'y')
{
rgpulse(d1,zero,2.0e-6,2.0e-6); /* presat */
obspower(tpwr); /* Set transmitter power for hard 1H pulses */
delay(2.0e-5);
if(fscuba[0] == 'y')
{
delay(2.2e-2);
rgpulse(pw,zero,2.0e-6,0.0);
rgpulse(2*pw,one,2.0e-6,0.0);
rgpulse(pw,zero,2.0e-6,0.0);
delay(2.2e-2);
}
}
else
{
delay(d1);
}
obspower(tpwr); /* Set transmitter power for hard 1H pulses */
txphase(zero);
dec2phase(zero);
decphase(zero);
delay(1.0e-5);
/* Begin Pulses */
status(C);
/* Prepare for signs of gradients 0 1 0 1 0 1 */
mod2(ct,v1);
rcvroff();
lk_hold();
delay(20.0e-6);
/* first ensure that magnetization does infact start on H and not C */
decrgpulse(pwc,zero,2.0e-6,2.0e-6);
delay(2.0e-6);
zgradpulse(gzlvl1,gt1);
delay(gstab);
/* this is the real start */
rgpulse(pw,zero,0.0,0.0); /* 90 deg 1H pulse */
delay(2.0e-6);
zgradpulse(gzlvl2,gt2);
delay(2.0e-6);
delay(taua - gt2 - 4.0e-6); /* taua <= 1/4JCH */
simpulse(2*pw,2*pwc,zero,zero,0.0,0.0);
txphase(one); decphase(t1);
delay(2.0e-6);
zgradpulse(gzlvl2,gt2);
delay(2.0e-6);
delay(taua - gt2 - 4.0e-6);
rgpulse(pw,one,0.0,0.0);
txphase(zero);
delay(2.0e-6);
zgradpulse(gzlvl3,gt3);
delay(gstab);
/* 2D decoupling on */
dec3phase(one);
dec3power(dpwr3);
dec3rgpulse(pwd1,one,4.0e-6,0.0);
dec3phase(zero);
dec3unblank();
dec3power(dpwr3_D); /* keep power down */
dec3prgon(ddseq,pwd,dresD);
dec3on();
/* 2D decoupling on */
decrgpulse(pwc,t1,2.0e-6,0.0);
decphase(zero);
delay(taub - 2.0*pw - 2.0e-6);
rgpulse(pw,zero,0.0,0.0);
rgpulse(pw,t2,2.0e-6,0.0);
delay(TC - taub
- gt4 - 102e-6
- PRG_STOP_DELAY - POWER_DELAY - pwd1
- 4.0e-6 - POWER_DELAY - 4.0e-6 - WFG_START_DELAY);
/* 2D decoupling off */
dec3off();
dec3prgoff();
dec3blank();
dec3phase(three);
dec3power(dpwr3);
dec3rgpulse(pwd1,three,4.0e-6,0.0);
/* 2D decoupling off */
ifzero(v1);
delay(2.0e-6);
zgradpulse(gzlvl4,gt4);
delay(gstab);
elsenz(v1);
delay(2.0e-6);
zgradpulse(-1.0*gzlvl4,gt4);
delay(gstab);
endif(v1);
initval(1.0,v3);
decstepsize(353.0);
dcplrphase(v3);
decpower(d_ca180);
decshaped_pulse(shca180,pwca180,zero,4.0e-6,0.0);
dcplrphase(zero);
ifzero(v1);
delay(2.0e-6);
zgradpulse(gzlvl4,gt4);
delay(gstab);
elsenz(v1);
delay(2.0e-6);
zgradpulse(-1.0*gzlvl4,gt4);
delay(gstab);
endif(v1);
/* 2D decoupling on */
dec3phase(one);
dec3power(dpwr3);
dec3rgpulse(pwd1,one,4.0e-6,0.0);
dec3phase(zero);
dec3unblank();
dec3power(dpwr3_D); /* keep power down */
dec3prgon(ddseq,pwd,dresD);
dec3on();
/* 2D decoupling on */
delay(TC - taud - WFG_STOP_DELAY - gt4 - 102e-6
- POWER_DELAY - 4.0e-6 - pwd1 - POWER_DELAY
- PRG_START_DELAY);
/* 2D decoupling off */
dec3off();
dec3prgoff();
dec3blank();
decphase(three);
dec3power(dpwr3);
dec3rgpulse(pwd1,three,4.0e-6,0.0);
/* 2D decoupling off */
delay(taud - PRG_STOP_DELAY -POWER_DELAY - pwd1 - 4.0e-6
- POWER_DELAY
- WFG_START_DELAY - pwca90 - 4.0e-6
- WFG_STOP_DELAY - POWER_DELAY - 4.0e-6);
decpower(d_ca90);
decshaped_pulse(shca90,pwca90,t3,4.0e-6,0.0);
decpower(dhpwr);
decrgpulse(pwc,one,4.0e-6,0.0);
/* T2 period */
dec3power(dpwr3);
dec3rgpulse(pwd1,t4,2.0e-6,0.0);
dec3phase(one);
dec3power(dpwr3_sl);
dec3rgpulse(time_T2,one,2.0e-6,2.0e-7);
dec3phase(zero);
dec3power(dpwr3);
dec3rgpulse(pwd1,zero,2.0e-6,0.0);
ifzero(v1);
delay(2.0e-6);
zgradpulse(gzlvl5,gt5);
delay(gstab);
elsenz(v1);
delay(2.0e-6);
zgradpulse(-1.0*gzlvl5,gt5);
delay(gstab);
endif(v1);
decphase(zero);
decrgpulse(pwc,t7,4.0e-6,0.0);
/* C' decoupling on */
decpower(dpwrsed);
decprgon(codecseq,pwcodec,dressed);
decon();
/* C' decoupling on */
if(taud + 3.0*POWER_DELAY + 2.0*PRG_START_DELAY + pwd1 + 4.0e-6 >= tau1) {
delay(tau1);
rgpulse(2.0*pw,zero,0.0,0.0);
delay(taud + 3.0*POWER_DELAY + 2.0*PRG_START_DELAY + pwd1 + 4.0e-6
- tau1);
/* 2D decoupling on */
dec3phase(t6);
dec3power(dpwr3);
dec3rgpulse(pwd1,t6,4.0e-6,0.0);
dec3phase(zero);
dec3unblank();
dec3power(dpwr3_D); /* keep power down */
dec3prgon(ddseq,pwd,dresD);
dec3on();
/* 2D decoupling on */
delay(TC - taud + tau1 - POWER_DELAY
- PRG_START_DELAY - 2.0*pw
- POWER_DELAY - pwd1 - 4.0e-6 - POWER_DELAY - PRG_START_DELAY
- 3.0*POWER_DELAY - 2.0*PRG_START_DELAY - pwd1 - 4.0e-6
- PRG_STOP_DELAY - POWER_DELAY - pwd1 - 4.0e-6
- PRG_STOP_DELAY
- POWER_DELAY - gt6 - 102e-6
- WFG_START_DELAY);
/* 2D decoupling off */
dec3off();
dec3prgoff();
dec3blank();
dec3power(dpwr3);
dec3rgpulse(pwd1,three,4.0e-6,0.0);
/* 2D decoupler off */
/* C' decoupling off */
decoff();
decprgoff();
decpower(d_ca180); /* set power for reburp */
/* C' decoupling off */
}
else {
delay(taud);
/* 2D decoupling on */
dec3phase(t6);
dec3power(dpwr3);
dec3rgpulse(pwd1,t6,4.0e-6,0.0);
dec3phase(zero);
dec3unblank();
dec3power(dpwr3_D); /* keep power down */
dec3prgon(ddseq,pwd,dresD);
dec3on();
/* 2D decoupling on */
delay(tau1 - taud - POWER_DELAY - PRG_START_DELAY
- POWER_DELAY - pwd1 - 4.0e-6
- POWER_DELAY - PRG_START_DELAY);
rgpulse(2.0*pw,zero,0.0,0.0);
delay(TC
- 2.0*pw - PRG_STOP_DELAY - POWER_DELAY - pwd1 - 4.0e-6
- POWER_DELAY
- PRG_STOP_DELAY - gt6 - 102e-6
- WFG_START_DELAY);
/* 2D decoupling off */
dec3off();
dec3prgoff();
dec3blank();
dec3phase(three);
dec3power(dpwr3);
dec3rgpulse(pwd1,three,4.0e-6,0.0);
/* 2D decoupler off */
/* C' decoupling off */
decoff();
decprgoff();
decpower(d_ca180); /* set power for reburp */
/* C' decoupling off */
}
initval(1.0,v4);
decstepsize(353.0);
dcplrphase(v4);
ifzero(v1);
delay(2.0e-6);
zgradpulse(gzlvl6,gt6);
delay(gstab);
elsenz(v1);
delay(2.0e-6);
zgradpulse(-1.0*gzlvl6,gt6);
delay(gstab);
endif(v1);
decshaped_pulse(shca180,pwca180,zero,0.0,0.0);
dcplrphase(zero);
ifzero(v1);
delay(2.0e-6);
zgradpulse(gzlvl6,gt6);
delay(gstab);
elsenz(v1);
delay(2.0e-6);
zgradpulse(-1.0*gzlvl6,gt6);
delay(gstab);
endif(v1);
/* C' decoupling on */
decpower(dpwrsed);
decprgon(codecseq,pwcodec,dressed);
decon();
/* C' decoupling on */
/* 2D decoupling on */
dec3phase(one);
dec3power(dpwr3);
dec3rgpulse(pwd1,one,4.0e-6,0.0);
dec3phase(zero);
dec3unblank();
dec3power(dpwr3_D); /* keep power down */
dec3prgon(ddseq,pwd,dresD);
dec3on();
/* 2D decoupling on */
delay(TC - tau1 - WFG_STOP_DELAY - gt6
- 102e-6 - POWER_DELAY - PRG_START_DELAY - POWER_DELAY - pwd1
- 4.0e-6 - POWER_DELAY - PRG_START_DELAY - PRG_STOP_DELAY
- POWER_DELAY - 4.0e-6);
/* C' decoupling off */
decoff();
decprgoff();
decpower(dhpwr);
/* C' decoupling off */
decrgpulse(pwc,one,4.0e-6,0.0);
/* 2D decoupling off */
dec3off();
dec3prgoff();
dec3blank();
dec3phase(three);
dec3power(dpwr3);
dec3rgpulse(pwd1,three,4.0e-6,0.0);
/* 2D decoupler off */
ifzero(v1);
delay(2.0e-6);
zgradpulse(gzlvl7,gt7);
delay(gstab);
elsenz(v1);
delay(2.0e-6);
zgradpulse(-1.0*gzlvl7,gt7);
delay(gstab);
endif(v1);
delay(lk_wait); /* delay for lk receiver recovery */
rgpulse(pw,zero,0.0,0.0);
delay(2.0e-6);
zgradpulse(gzlvl8,gt8);
decphase(zero);
delay(taua - gt8 - 4.0e-6);
simpulse(2*pw,2*pwc,zero,zero,0.0,0.0);
delay(2.0e-6);
zgradpulse(gzlvl8,gt8);
delay(2.0e-6);
delay(taua - 2*POWER_DELAY - gt8 - 4.0e-6);
decpower(dpwr); /* Set power for decoupling */
dec2power(dpwr2); /* Set power for decoupling */
rgpulse(pw,zero,0.0,rof2);
lk_sample();
/* rcvron(); */ /* Turn on receiver to warm up before acq */
/* BEGIN ACQUISITION */
status(D);
setreceiver(t5);
}
pulsesequence()
{
/* DECLARE AND LOAD VARIABLES */
char f1180[MAXSTR], /* Flag to start t1 @ halfdwell */
f2180[MAXSTR], /* Flag to start t2 @ halfdwell */
mag_flg[MAXSTR], /* magic-angle coherence transfer gradients */
TROSY[MAXSTR]; /* do TROSY on N15 and H1 */
int icosel, /* used to get n and p type */
t1_counter, /* used for states tppi in t1 */
t2_counter, /* used for states tppi in t2 */
ni = getval("ni"),
ni2 = getval("ni2");
double tau1, /* t1 delay */
tau2, /* t2 delay */
t1a, /* time increments for first dimension */
t1b,
t1c,
tauCH = getval("tauCH"), /* 1/4J delay for CH */
timeTN = getval("timeTN"), /* constant time for 15N evolution */
timeAB = getval("timeAB"), /* set timeAB=1.9e-3 to get only Ha */
/* set timeAB=3.3e-3 to maximize Hb */
/* set timeAB=2.8e-3 for both Ha/Hb */
zeta = 3.0e-3,
eta = 4.6e-3,
theta = 14.0e-3,
kappa = 5.4e-3,
lambda = 2.4e-3,
sheila, /* to transfer J evolution time hyperbolically into tau1 */
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
rf0, /* maximum fine power when using pwC pulses */
/* 90 degree pulse at Cab(46ppm), first off-resonance null at CO (174ppm) */
pwC1, /* 90 degree pulse length on C13 at rf1 */
rf1, /* fine power for 5.1 kHz rf for 600MHz magnet */
/* 180 degree pulse at Cab(46ppm), first off-resonance null at CO(174ppm) */
pwC2, /* 180 degree pulse length at rf2 */
rf2, /* fine power for 11.4 kHz rf for 600MHz magnet */
/* the following pulse lengths for SLP pulses are automatically calculated */
/* by the macro "proteincal". SLP pulse shapes, "offC4" etc are called */
/* directly from your shapelib. */
pwC4 = getval("pwC4"), /*180 degree pulse at Ca(56ppm) null at CO(174ppm) */
pwC5 = getval("pwC5"), /* 90 degree selective sinc pulse on CO(174ppm) */
pwC7 = getval("pwC7"), /* 180 degree selective sinc pulse on CO(174ppm) */
rf4, /* fine power for the pwC4 ("offC4") pulse */
rf5, /* fine power for the pwC5 ("offC5") pulse */
rf7, /* fine power for the pwC7 ("offC7") pulse */
compH = getval("compH"), /* adjustment for C13 amplifier compression */
compC = getval("compC"), /* adjustment for C13 amplifier compression */
phi7cal = getval("phi7cal"), /* phase in degrees of the last C13 90 pulse */
pwH, /* H1 90 degree pulse length at tpwr1 */
tpwr1, /* 7.3 kHz rf for DIPSI-2 */
DIPSI2time, /* total length of DIPSI-2 decoupling */
ncyc_dec,
waltzB1=getval("waltzB1"), /* RF strength for 1H decoupling */
pwNlvl = getval("pwNlvl"), /* power for N15 pulses */
pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */
sw1 = getval("sw1"),
sw2 = getval("sw2"),
gt1 = getval("gt1"), /* coherence pathway gradients */
gzcal = getval("gzcal"), /* g/cm to DAC conversion factor */
gzlvl1 = getval("gzlvl1"),
gzlvl2 = getval("gzlvl2"),
gt0 = getval("gt0"), /* other gradients */
gt3 = getval("gt3"),
gt4 = getval("gt4"),
gt5 = getval("gt5"),
gstab = getval("gstab"),
gzlvl0 = getval("gzlvl0"),
gzlvl3 = getval("gzlvl3"),
gzlvl4 = getval("gzlvl4"),
gzlvl5 = getval("gzlvl5"),
gzlvl6 = getval("gzlvl6");
getstr("f1180",f1180);
getstr("f2180",f2180);
getstr("mag_flg",mag_flg);
getstr("TROSY",TROSY);
/* LOAD PHASE TABLE */
settable(t3,1,phx);
settable(t4,1,phx);
settable(t5,2,phi5);
settable(t6,2,phi6);
if (TROSY[A]=='y')
{settable(t8,1,phy);
settable(t9,1,phx);
settable(t10,1,phy);
settable(t11,1,phx);
settable(t12,2,recT);}
else
{settable(t8,1,phx);
settable(t9,8,phi9);
settable(t10,1,phx);
settable(t11,1,phy);
settable(t12,4,rec);}
/* INITIALIZE VARIABLES */
if( dpwrf < 4095 )
{ printf("reset dpwrf=4095 and recalibrate C13 90 degree pulse");
psg_abort(1); }
if( pwC > 24.0e-6*600.0/sfrq )
{ printf("increase pwClvl so that pwC < 24*600/sfrq");
psg_abort(1); }
/* maximum fine power for pwC pulses */
rf0 = 4095.0;
/* 90 degree pulse on Cab, null at CO 128ppm away */
pwC1 = sqrt(15.0)/(4.0*128.0*dfrq);
rf1 = (compC*4095.0*pwC)/pwC1;
rf1 = (int) (rf1 + 0.5);
/* 180 degree pulse on Cab, null at CO 128ppm away */
pwC2 = sqrt(3.0)/(2.0*128.0*dfrq);
rf2 = (4095.0*compC*pwC*2.0)/pwC2;
rf2 = (int) (rf2 + 0.5);
/* 180 degree pulse on Ca, null at CO 118ppm away */
rf4 = (compC*4095.0*pwC*2.0)/pwC4;
rf4 = (int) (rf4 + 0.5);
/* 90 degree one-lobe sinc pulse on CO, null at Ca 118ppm away */
rf5 = (compC*4095.0*pwC*1.69)/pwC5; /* needs 1.69 times more */
rf5 = (int) (rf5 + 0.5); /* power than a square pulse */
/* 180 degree one-lobe sinc pulse on CO, null at Ca 118ppm away */
rf7 = (compC*4095.0*pwC*2.0*1.65)/pwC7; /* needs 1.65 times more */
rf7 = (int) (rf7 + 0.5); /* power than a square pulse */
/* power level and pulse times for DIPSI 1H decoupling */
DIPSI2time = 2.0*3.0e-3 + 2.0*14.0e-3 + 2.0*timeTN - 5.4e-3 + 0.5*pwC1 + 2.0*pwC5 + 5.0*pwN + 2.0*gt3 + 1.0e-4 + 4.0*GRADIENT_DELAY + 2.0*POWER_DELAY + 8.0*PRG_START_DELAY;
pwH = 1.0/(4.0*waltzB1);
ncyc_dec = (DIPSI2time*90.0)/(pwH*2590.0*4.0);
ncyc_dec = (int) (ncyc_dec+0.5);
pwH = (DIPSI2time*90.0)/(ncyc_dec*2590.0*4.0); /*fine correction of pwH */
tpwr1 = 4095.0*(compH*pw/pwH);
tpwr1 = (int) (2.0*tpwr1 + 0.5); /* x2 because obs atten will be reduced by 6dB */
if (ix == 1)
{
fprintf(stdout, "\nNo of DIPSI-2 cycles = %4.1f\n",ncyc_dec);
fprintf(stdout, "\nfine power for DIPSI-2 pulse =%6.1f\n",tpwr1);
}
/* CHECK VALIDITY OF PARAMETER RANGES */
if ( 0.5*ni2*1/(sw2) > timeTN - WFG3_START_DELAY)
{ printf(" ni2 is too big. Make ni2 equal to %d or less.\n",
((int)((timeTN - WFG3_START_DELAY)*2.0*sw2))); psg_abort(1);}
if ( dm[A] == 'y' || dm[B] == 'y' || dm[C] == 'y' )
{ printf("incorrect dec1 decoupler flags! Should be 'nnn' "); psg_abort(1);}
if ( dm2[A] == 'y' || dm2[B] == 'y' )
{ printf("incorrect dec2 decoupler flags! Should be 'nny' "); psg_abort(1);}
if ( dm3[A] == 'y' || dm3[C] == 'y' )
{ printf("incorrect dec3 decoupler flags! Should be 'nyn' or 'nnn' ");
psg_abort(1);}
if ( dpwr2 > 50 )
{ printf("dpwr2 too large! recheck value "); psg_abort(1);}
if ( pw > 20.0e-6 )
{ printf(" pw too long ! recheck value "); psg_abort(1);}
if ( pwN > 100.0e-6 )
{ printf(" pwN too long! recheck value "); psg_abort(1);}
if ( TROSY[A]=='y' && dm2[C] == 'y' )
{ text_error("Choose either TROSY='n' or dm2='n' ! "); psg_abort(1);}
/* PHASES AND INCREMENTED TIMES */
/* Phase incrementation for hypercomplex 2D data, States-Haberkorn element */
if (phase1 == 2) tsadd(t3,1,4);
if (TROSY[A]=='y')
{ if (phase2 == 2) icosel = +1;
else {tsadd(t4,2,4); tsadd(t10,2,4); icosel = -1;}
}
else { if (phase2 == 2) {tsadd(t10,2,4); icosel = +1;}
else icosel = -1;
}
/* Set up f1180 */
tau1 = d2;
if((f1180[A] == 'y') && (ni > 1.0))
{ tau1 += ( 1.0 / (2.0*sw1) ); if(tau1 < 0.2e-6) tau1 = 0.0; }
tau1 = tau1/2.0;
/* Hyperbolic sheila seems superior to original zeta approach */
/* subtract unavoidable delays from tauCH */
tauCH = tauCH - gt0 - 2.0*GRADIENT_DELAY - 5.0e-5;
if ((ni-1)/(2.0*sw1) > 2.0*tauCH)
{
if (tau1 > 2.0*tauCH) sheila = tauCH;
else if (tau1 > 0) sheila = 1.0/(1.0/tau1+1.0/tauCH-1.0/(2.0*tauCH));
else sheila = 0.0;
}
else
{
if (tau1 > 0) sheila = 1.0/(1.0/tau1 + 1.0/tauCH - 2.0*sw1/((double)(ni-1)));
else sheila = 0.0;
}
t1a = tau1 + tauCH;
t1b = tau1 - sheila;
t1c = tauCH - sheila;
/* Set up f2180 */
tau2 = d3;
if((f2180[A] == 'y') && (ni2 > 1.0))
{ tau2 += ( 1.0 / (2.0*sw2) ); if(tau2 < 0.2e-6) tau2 = 0.0; }
tau2 = tau2/2.0;
/* Calculate modifications to phases for States-TPPI acquisition */
if( ix == 1) d2_init = d2;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if(t1_counter % 2)
{ tsadd(t3,2,4); tsadd(t12,2,4); }
if( ix == 1) d3_init = d3;
t2_counter = (int) ( (d3-d3_init)*sw2 + 0.5 );
if(t2_counter % 2)
{ tsadd(t8,2,4); tsadd(t12,2,4); }
/* For ni<2 (calibration) set timeAB=1.5ms to get avoid signal cancellation between Ha and Hb */
if (ni < 2.0) timeAB=1.5e-3;
/* BEGIN PULSE SEQUENCE */
status(A);
delay(d1);
if ( dm3[B] == 'y' )
lk_sample(); /*freezes z0 correction, stops lock pulsing*/
if ((ni/sw1-d2)>0)
delay(ni/sw1-d2); /*decreases as t1 increases for const.heating*/
if ((ni2/sw2-d3)>0)
delay(ni2/sw2-d3); /*decreases as t2 increases for const.heating*/
if ( dm3[B] == 'y' )
{ lk_hold(); lk_sampling_off();} /*freezes z0 correction, stops lock pulsing*/
rcvroff();
obspower(tpwr);
decpower(pwClvl);
dec2power(pwNlvl);
decpwrf(rf0);
obsoffset(tof);
txphase(one);
delay(1.0e-5);
if (TROSY[A] == 'n')
dec2rgpulse(pwN, zero, 0.0, 0.0); /*destroy N15 and C13 magnetization*/
decrgpulse(pwC, zero, 0.0, 0.0);
zgradpulse(gzlvl0, 0.5e-3);
delay(1.0e-4);
if (TROSY[A] == 'n')
dec2rgpulse(pwN, one, 0.0, 0.0);
decrgpulse(pwC, zero, 0.0, 0.0);
zgradpulse(0.7*gzlvl0, 0.5e-3);
delay(5.0e-4);
if ( dm3[B] == 'y' ) /* begins optional 2H decoupling */
{
gzlvl0=0.0; gzlvl3=0.0; gzlvl4=0.0; /* no gradients during 2H decoupling */
dec3rgpulse(1/dmf3,one,10.0e-6,2.0e-6);
dec3unblank();
dec3phase(zero);
delay(2.0e-6);
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
}
rgpulse(pw, one, 0.0, 0.0); /* 1H pulse excitation */
/* point a */
txphase(zero);
decphase(zero);
zgradpulse(gzlvl0, gt0); /* 2.0*GRADIENT_DELAY */
delay(5.0e-5);
if((t1a -2.0*pwC) > 0.0) delay(t1a - 2.0*pwC);
decrgpulse(2.0*pwC, zero, 0.0, 0.0);
delay(t1b);
rgpulse(2.0*pw, zero, 0.0, 0.0);
zgradpulse(gzlvl0, gt0); /* 2.0*GRADIENT_DELAY */
txphase(t3);
delay(5.0e-5);
delay(t1c);
/* point b */
rgpulse(pw, t3, 0.0, 0.0);
zgradpulse(gzlvl3, gt3);
delay(2.0e-4);
decrgpulse(pwC, zero, 0.0, 0.0);
/* point c */
zgradpulse(gzlvl4, gt4);
decpwrf(rf2);
delay(timeAB - gt4);
simpulse(2*pw, pwC2, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl4, gt4);
delay(timeAB - gt4);
/* point d */
/* ghc_co_nh STOPS HERE */
/* gcbca_co_nh STARTS HERE */
decpwrf(rf1); /* point b */
decrgpulse(pwC1, zero, 2.0e-6, 0.0);
obspwrf(tpwr1); obspower(tpwr-6); /* POWER_DELAY */
obsprgon("dipsi2", pwH, 5.0); /* PRG_START_DELAY */
xmtron();
/* point c */
decpwrf(rf0);
decphase(t5);
delay(zeta - 2.0*POWER_DELAY - PRG_START_DELAY - 0.5*10.933*pwC);
decrgpulse(pwC*158.0/90.0, t5, 0.0, 0.0);
decrgpulse(pwC*171.2/90.0, t6, 0.0, 0.0);
decrgpulse(pwC*342.8/90.0, t5, 0.0, 0.0); /* Shaka composite */
decrgpulse(pwC*145.5/90.0, t6, 0.0, 0.0);
decrgpulse(pwC*81.2/90.0, t5, 0.0, 0.0);
decrgpulse(pwC*85.3/90.0, t6, 0.0, 0.0);
decpwrf(rf1);
decphase(zero);
delay(zeta - 0.5*10.933*pwC - 0.5*pwC1);
/* point d */
decrgpulse(pwC1, zero, 0.0, 0.0);
decphase(t5);
decpwrf(rf5);
if ( dm3[B] == 'y' ) /* turns off 2H decoupling */
{
setstatus(DEC3ch, FALSE, 'c', FALSE, dmf3);
dec3rgpulse(1/dmf3,three,2.0e-6,2.0e-6);
dec3blank();
lk_autotrig(); /* resumes lock pulsing */
}
zgradpulse(gzlvl3, gt3);
delay(2.0e-4);
decshaped_pulse("offC5", pwC5, t5, 0.0, 0.0);
/* point e */
decpwrf(rf4);
decphase(zero);
delay(eta);
decshaped_pulse("offC4", pwC4, zero, 0.0, 0.0);
decpwrf(rf7);
dec2phase(zero);
delay(theta - eta - pwC4 - WFG3_START_DELAY);
/* WFG3_START_DELAY */
sim3shaped_pulse("", "offC7", "", 0.0, pwC7, 2.0*pwN, zero, zero, zero,
0.0, 0.0);
decpwrf(rf5);
decpwrf(rf5);
initval(phi7cal, v7);
decstepsize(1.0);
dcplrphase(v7); /* SAPS_DELAY */
dec2phase(t8);
delay(theta - SAPS_DELAY);
/* point f */
decshaped_pulse("offC5", pwC5, zero, 0.0, 0.0);
/* xxxxxxxxxxxxxxxxxx OPTIONS FOR N15 EVOLUTION xxxxxxxxxxxxxxxxxxxxx */
zgradpulse(gzlvl3, gt3);
if (TROSY[A]=='y') { xmtroff(); obsprgoff(); }
delay(2.0e-4);
dcplrphase(zero);
dec2rgpulse(pwN, t8, 0.0, 0.0);
decpwrf(rf7);
decphase(zero);
dec2phase(t9);
delay(timeTN - WFG3_START_DELAY - tau2);
/* WFG3_START_DELAY */
sim3shaped_pulse("", "offC7", "", 0.0, pwC7, 2.0*pwN, zero, zero, t9,
0.0, 0.0);
dec2phase(t10);
decpwrf(rf4);
if (TROSY[A]=='y')
{
if (tau2 > gt1 + 2.0*GRADIENT_DELAY + 1.0e-4)
{
txphase(t4);
delay(timeTN - pwC4 - WFG_START_DELAY); /* WFG_START_DELAY */
decshaped_pulse("offC4", pwC4, zero, 0.0, 0.0);
delay(tau2 - gt1 - 2.0*GRADIENT_DELAY - 1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspwrf(4095.0); obspower(tpwr); /* POWER_DELAY */
delay(1.0e-4 - 2.0*POWER_DELAY);
}
else
{
txphase(t4);
delay(timeTN -pwC4 -WFG_START_DELAY -gt1 -2.0*GRADIENT_DELAY -1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspwrf(4095.0); obspower(tpwr); /* POWER_DELAY */
delay(1.0e-4 - 2.0*POWER_DELAY); /* WFG_START_DELAY */
decshaped_pulse("offC4", pwC4, zero, 0.0, 0.0);
delay(tau2);
}
}
else
{
if (tau2 > kappa)
{
delay(timeTN - pwC4 - WFG_START_DELAY); /* WFG_START_DELAY */
decshaped_pulse("offC4", pwC4, zero, 0.0, 0.0);
delay(tau2 - kappa - PRG_STOP_DELAY);
xmtroff();
obsprgoff(); /* PRG_STOP_DELAY */
txphase(t4);
delay(kappa - gt1 - 2.0*GRADIENT_DELAY - 1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspwrf(4095.0); obspower(tpwr); /* POWER_DELAY */
delay(1.0e-4 - 2.0*POWER_DELAY);
}
else if (tau2 > (kappa - pwC4 - WFG_START_DELAY))
{
delay(timeTN + tau2 - kappa - PRG_STOP_DELAY);
xmtroff();
obsprgoff(); /* PRG_STOP_DELAY */
txphase(t4); /* WFG_START_DELAY */
decshaped_pulse("offC4", pwC4, zero, 0.0, 0.0);
delay(kappa -pwC4 -WFG_START_DELAY -gt1 -2.0*GRADIENT_DELAY -1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspwrf(4095.0); obspower(tpwr); /* POWER_DELAY */
delay(1.0e-4 - 2.0*POWER_DELAY);
}
else if (tau2 > gt1 + 2.0*GRADIENT_DELAY + 1.0e-4)
{
delay(timeTN + tau2 - kappa - PRG_STOP_DELAY);
xmtroff();
obsprgoff(); /* PRG_STOP_DELAY */
txphase(t4);
delay(kappa - tau2 - pwC4 - WFG_START_DELAY); /* WFG_START_DELAY */
decshaped_pulse("offC4", pwC4, zero, 0.0, 0.0);
delay(tau2 - gt1 - 2.0*GRADIENT_DELAY - 1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspwrf(4095.0); obspower(tpwr); /* POWER_DELAY */
delay(1.0e-4 - 2.0*POWER_DELAY);
}
else
{
delay(timeTN + tau2 - kappa - PRG_STOP_DELAY);
xmtroff();
obsprgoff(); /* PRG_STOP_DELAY */
txphase(t4);
delay(kappa-tau2-pwC4-WFG_START_DELAY-gt1-2.0*GRADIENT_DELAY-1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspwrf(4095.0); obspower(tpwr); /* POWER_DELAY */
delay(1.0e-4 - 2.0*POWER_DELAY); /* WFG_START_DELAY */
decshaped_pulse("offC4", pwC4, zero, 0.0, 0.0);
delay(tau2);
}
} /* point g */
/* xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx */
if (TROSY[A]=='y') rgpulse(pw, t4, 0.0, 0.0);
else sim3pulse(pw, 0.0, pwN, t4, zero, t10, 0.0, 0.0);
txphase(zero);
dec2phase(zero);
zgradpulse(gzlvl5, gt5);
if (TROSY[A]=='y') delay(lambda - 0.65*(pw + pwN) - gt5);
else delay(lambda - 1.3*pwN - gt5);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl5, gt5);
txphase(one);
dec2phase(t11);
delay(lambda - 1.3*pwN - gt5);
sim3pulse(pw, 0.0, pwN, one, zero, t11, 0.0, 0.0);
txphase(zero);
dec2phase(zero);
zgradpulse(gzlvl6, gt5);
delay(lambda - 1.3*pwN - gt5);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
dec2phase(t10);
zgradpulse(gzlvl6, gt5);
if (TROSY[A]=='y') delay(lambda - 1.6*pwN - gt5);
else delay(lambda - 0.65*pwN - gt5);
if (TROSY[A]=='y') dec2rgpulse(pwN, t10, 0.0, 0.0);
else rgpulse(pw, zero, 0.0, 0.0);
delay((gt1/10.0) + 1.0e-4 +gstab - 0.5*pw + 2.0*GRADIENT_DELAY + POWER_DELAY);
rgpulse(2.0*pw, zero, 0.0, rof1);
dec2power(dpwr2); /* POWER_DELAY */
if (mag_flg[A] == 'y') magradpulse(icosel*gzcal*gzlvl2, gt1/10.0);
else zgradpulse(icosel*gzlvl2, gt1/10.0); /* 2.0*GRADIENT_DELAY */
delay(gstab);
rcvron();
statusdelay(C,1.0e-4 - rof1);
if (dm3[B]=='y') lk_sample();
setreceiver(t12);
}
pulsesequence()
{
/* DECLARE VARIABLES */
char fsat[MAXSTR],
fscuba[MAXSTR],
f1180[MAXSTR], /* Flag to start t1 @ halfdwell */
sh_reb[MAXSTR],
codec[MAXSTR],
MQ_flg[MAXSTR],
filter_flg[MAXSTR];
int phase,
t1_counter; /* used for states tppi in t1 */
double tau1, /* t1 delay */
taua, /* set to exactly 1/4JCH */
tsatpwr, /* low level 1H trans.power for presat */
sw1, /* sweep width in f1 */
tpwr_cp, /* power level for 1H CPMG */
pw_cp, /* 1H pw for CPMG */
ncyc_cp, /* number of CPMG cycles */
time_T2, /* total time for CPMG trains */
tau_cpmg,
dhpwr,
pwc,
dmf_co,
dpwr_co,
dresco,
gt0,
gt1,
gt2,
gt3,
gt4,
gt5,
gt6,
gzlvl0,
gzlvl1,
gzlvl2,
gzlvl3,
gzlvl4,
gzlvl5,
gzlvl6,
tpwr,
pw,
d_reb,
pwc_reb,
dpwr3_D,
pwd,
pwd1,
tau_eq,
pwn,
dhpwr2;
/* LOAD VARIABLES */
getstr("fsat",fsat);
getstr("f1180",f1180);
getstr("fscuba",fscuba);
getstr("sh_reb",sh_reb);
getstr("codec",codec);
getstr("MQ_flg",MQ_flg);
getstr("filter_flg",filter_flg);
taua = getval("taua");
tpwr = getval("tpwr");
tsatpwr = getval("tsatpwr");
dpwr = getval("dpwr");
phase = (int) ( getval("phase") + 0.5);
sw1 = getval("sw1");
tpwr_cp = getval("tpwr_cp");
pw_cp = getval("pw_cp");
ncyc_cp = getval("ncyc_cp");
time_T2 = getval("time_T2");
dhpwr = getval("dhpwr");
pwc = getval("pwc");
pwn = getval("pwn");
dhpwr2 = getval("dhpwr2");
dmf_co = getval("dmf_co");
dpwr_co = getval("dpwr_co");
dresco = getval("dresco");
gt0 = getval("gt0");
gt1 = getval("gt1");
gt2 = getval("gt2");
gt3 = getval("gt3");
gt4 = getval("gt4");
gt5 = getval("gt5");
gt6 = getval("gt6");
gzlvl0 = getval("gzlvl0");
gzlvl1 = getval("gzlvl1");
gzlvl2 = getval("gzlvl2");
gzlvl3 = getval("gzlvl3");
gzlvl4 = getval("gzlvl4");
gzlvl5 = getval("gzlvl5");
gzlvl6 = getval("gzlvl6");
tpwr = getval("tpwr");
pw = getval("pw");
d_reb = getval("d_reb");
pwc_reb = getval("pwc_reb");
dpwr3_D = getval("dpwr3_D");
pwd = getval("pwd");
pwd1 = getval("pwd1");
tau_eq = getval("tau_eq");
/* LOAD PHASE TABLE */
settable(t1,4,phi1);
settable(t2,2,phi2);
settable(t4,8,phi4);
settable(t5,4,rec);
/* CHECK VALIDITY OF PARAMETER RANGES */
if((dm[A] == 'y' || dm[B] == 'y' || dm[C] == 'y' ))
{
printf("incorrect dec1 decoupler flags! ");
abort(1);
}
if((dm2[A] == 'y' || dm2[B] == 'y' || dm2[C] == 'y' || dm2[D] == 'y'))
{
printf("incorrect dec2 decoupler flags! ");
abort(1);
}
if( tsatpwr > 6 )
{
printf("TSATPWR too large !!! ");
abort(1);
}
if( dpwr > 48 )
{
printf("don't fry the probe, DPWR too large! ");
abort(1);
}
if(tpwr_cp > 62)
{
printf("don't fry the probe, tpwr_cp too large: < 62! ");
abort(1);
}
if(pw_cp < 9.5e-6) {
printf("pw_cp is too low; > 9.5us\n");
abort(1);
}
if( dpwr2 > -16 )
{
printf("don't fry the probe, DPWR2 too large! ");
abort(1);
}
if( pw > 20.0e-6 )
{
printf("dont fry the probe, pw too high ! ");
abort(1);
}
if(gt1 > 3e-3 || gt2 > 3e-3 || gt3 > 3e-3 || gt4 > 3e-3
|| gt5 > 3e-3 || gt6 > 3e-3)
{
printf("gradients on for too long. Must be < 3e-3 \n");
abort(1);
}
if(ncyc_cp > 80) {
printf("ncyc_cp is too large; must be less than 81\n");
abort(1);
}
if(time_T2 > .080) {
printf("time_T2 is too large; must be less than 80 ms\n");
abort(1);
}
if(ncyc_cp > 0) {
tau_cpmg = time_T2/(4.0*ncyc_cp) - pw_cp;
if(ix==1)
printf("nuCPMG for curent experiment is (Hz): %5.3f\n",1/(4.0*(tau_cpmg+pw_cp)));
}
else {
tau_cpmg = time_T2/(4.0) - pw_cp;
if(ix==1)
printf("nuCPMG for curent experiment is (Hz): not applicable");
}
if(tau_cpmg + pw_cp < 125e-6) {
printf("tau_cpmg is too small; decrease ncyc_cp\n");
abort(1);
}
if(dpwr_co > 42) {
printf("dpwr_co is too high; < 42\n");
abort(1);
}
if(dpwr3_D > 51) {
printf("dpwr3_D is too high; < 52\n");
abort(1);
}
if(dpwr3 > 59) {
printf("dpwr3 is too high; < 60\n");
abort(1);
}
if(ix==1)
printf("If at 800 turn dpwr3=-16, pwd1=0\n");
/* Phase incrementation for hypercomplex 2D data */
if (phase == 2)
tsadd(t1,1,4);
/* Set up f1180 tau1 = t1 */
tau1 = d2;
if(MQ_flg[A] == 'n')
tau1 = tau1 - 4.0/PI*pwc - POWER_DELAY - PRG_START_DELAY
- 2.0*pw - 2.0*pwn - PRG_STOP_DELAY - POWER_DELAY
- 4.0e-6;
else
tau1 = tau1 - 4.0/PI*pwc - POWER_DELAY - PRG_START_DELAY
- 2.0*pw - 2.0*pwn - PRG_STOP_DELAY - POWER_DELAY
- 4.0e-6;
if(f1180[A] == 'y') {
tau1 += ( 1.0 / (2.0*sw1));
if(tau1 < 0.4e-6) tau1 = 0.4e-6;
}
if(tau1 < 0.4e-6)
tau1 = 0.4e-6;
tau1 = tau1/2.0;
/* Calculate modifications to phases for States-TPPI acquisition */
if( ix == 1) d2_init = d2 ;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if(t1_counter % 2) {
tsadd(t1,2,4);
tsadd(t5,2,4);
}
/* BEGIN ACTUAL PULSE SEQUENCE */
status(A);
rlpower(tsatpwr,TODEV); /* Set transmitter power for 1H presaturation */
rlpower(dhpwr,DODEV); /* Set Dec1 power for 13C pulses */
rlpower(dhpwr2,DO2DEV); /* Set Dec2 power for 15N pulses */
obsoffset(tof);
/* Presaturation Period */
status(B);
if (fsat[0] == 'y')
{
delay(2.0e-5);
rgpulse(d1,zero,2.0e-6,2.0e-6); /* presaturation */
rlpower(tpwr,TODEV); /* Set transmitter power for hard 1H pulses */
delay(2.0e-5);
if(fscuba[0] == 'y')
{
delay(2.2e-2);
rgpulse(pw,zero,2.0e-6,0.0);
rgpulse(2*pw,one,2.0e-6,0.0);
rgpulse(pw,zero,2.0e-6,0.0);
delay(2.2e-2);
}
}
else
{
delay(d1);
}
rlpower(tpwr,TODEV); /* Set transmitter power for 1H CPMG pulses */
txphase(zero);
dec2phase(zero);
decphase(zero);
delay(1.0e-5);
/* Begin Pulses */
status(C);
rcvroff();
delay(20.0e-6);
decrgpulse(pwc,zero,4.0e-6,0.0);
delay(2.0e-6);
rgradient('z',gzlvl1);
delay(gt1);
rgradient('z',0.0);
delay(250.0e-6);
rgpulse(pw,zero,0.0,0.0);
decpower(d_reb);
delay(2.0e-6);
rgradient('z',gzlvl2);
delay(gt2);
rgradient('z',0.0);
delay(150.0e-6);
if(filter_flg[A] == 'y')
delay(taua - POWER_DELAY - gt2 - 152e-6
- WFG2_START_DELAY - 0.5*pwc_reb - 4.0/PI*pw);
else
delay(taua - POWER_DELAY - gt2 - 152e-6
- WFG2_START_DELAY - 0.5*pwc_reb);
simshaped_pulse("hard",sh_reb,2.0*pw,pwc_reb,zero,zero,0.0,0.0);
txphase(one);
decpower(dhpwr);
decphase(t4);
delay(taua - 0.5*pwc_reb - WFG2_STOP_DELAY - POWER_DELAY - gt2 - 152e-6 );
delay(2.0e-6);
rgradient('z',gzlvl2);
delay(gt2);
rgradient('z',0.0);
delay(150.0e-6);
if(filter_flg[A] == 'n')
rgpulse(pw,one,0.0,0.0);
if(filter_flg[A] == 'y') {
decrgpulse(pwc,t4,0.,0.);
decpower(d_reb);
decphase(zero);
delay(2.0e-6);
rgradient('z',gzlvl0);
delay(gt0);
rgradient('z',0.0);
delay(150.0e-6);
delay(taua - POWER_DELAY - gt0 - 152e-6
- WFG2_START_DELAY - 0.5*pwc_reb);
simshaped_pulse("hard",sh_reb,2.0*pw,pwc_reb,zero,zero,0.0,0.0);
txphase(one);
decpower(dhpwr);
decphase(t4);
delay(taua - 0.5*pwc_reb - WFG2_STOP_DELAY - POWER_DELAY - gt0 - 152e-6 );
delay(2.0e-6);
rgradient('z',gzlvl0);
delay(gt0);
rgradient('z',0.0);
delay(150.0e-6);
decrgpulse(pwc,t4,0.0,0.0);
rgpulse(pw,one,0.0,0.0);
}
decphase(t1);
delay(2.0e-6);
rgradient('z',gzlvl3);
delay(gt3);
rgradient('z',0.0);
delay(250.0e-6);
/* turn on 2H decoupling */
dec3phase(one);
dec3power(dpwr3);
dec3rgpulse(pwd1,one,4.0e-6,0.0);
dec3phase(zero);
dec3unblank();
dec3power(dpwr3_D);
dec3prgon(dseq3,pwd,dres3);
dec3on();
/* turn on 2H decoupling */
if(MQ_flg[A] == 'y') {
rgpulse(pw,zero,2.0e-6,0.0);
delay(2.0*pwn - PRG_START_DELAY - PRG_STOP_DELAY);
}
decrgpulse(pwc,t1,4.0e-6,0.0);
decphase(zero);
/* 13CO decoupling on */
decpower(dpwr_co);
decprgon(codec,1.0/dmf_co,dresco);
decon();
/* 13CO decoupling on */
delay(tau1);
rgpulse(2.0*pw,zero,0.0,0.0);
dec2rgpulse(2.0*pwn,zero,0.0,0.0);
delay(tau1);
/* 13CO decoupling off */
decoff();
decprgoff();
/* 13CO decoupling off */
decpower(dhpwr);
decrgpulse(pwc,zero,4.0e-6,0.0);
if(MQ_flg[A] == 'y')
rgpulse(pw,zero,0.0,0.0);
/* turn off decoupling */
dec3off();
dec3prgoff();
dec3blank();
dec3phase(three);
dec3power(dpwr3);
dec3rgpulse(pwd1,three,4.0e-6,0.0);
/* turn off decoupling */
obspower(tpwr_cp);
if(MQ_flg[A] == 'n') {
delay(2.0e-6);
rgradient('z',gzlvl4);
delay(gt4);
rgradient('z',0.0);
delay(250.0e-6);
}
else {
delay(2.0e-6);
rgradient('z',-1.0*gzlvl4);
delay(gt4);
rgradient('z',0.0);
delay(250.0e-6);
}
/* now include a delay to allow the spin system to equilibrate */
delay(tau_eq);
rgpulse(pw_cp,t2,4.0e-6,0.0);
txphase(one);
/* start of the CPMG period 1 */
if(ncyc_cp == 1) {
delay(tau_cpmg - (2.0/PI)*pw_cp);
rgpulse(2.0*pw_cp,one,0.0,0.0);
delay(tau_cpmg);
}
if(ncyc_cp == 2) {
delay(tau_cpmg - (2.0/PI)*pw_cp);
rgpulse(2.0*pw_cp,one,0.0,0.0);
delay(tau_cpmg);
delay(tau_cpmg);
rgpulse(2.0*pw_cp,one,0.0,0.0);
delay(tau_cpmg);
}
if(ncyc_cp > 2) {
delay(tau_cpmg - (2.0/PI)*pw_cp);
rgpulse(2.0*pw_cp,one,0.0,0.0);
delay(tau_cpmg);
initval(ncyc_cp-2,v4);
loop(v4,v5);
delay(tau_cpmg);
rgpulse(2.0*pw_cp,one,0.0,0.0);
delay(tau_cpmg);
endloop(v5);
delay(tau_cpmg);
rgpulse(2.0*pw_cp,one,0.0,0.0);
delay(tau_cpmg);
}
txphase(t4); decphase(zero);
rgpulse(2.0*pw_cp,t4,2.0e-6,2.0e-6);
txphase(one);
if(ncyc_cp == 1) {
delay(tau_cpmg);
rgpulse(2.0*pw_cp,one,0.0,0.0); txphase(one);
delay(tau_cpmg - 2.0/PI*pw_cp);
}
if(ncyc_cp == 2) {
delay(tau_cpmg);
rgpulse(2.0*pw_cp,one,0.0,0.0);
delay(tau_cpmg);
delay(tau_cpmg);
rgpulse(2.0*pw_cp,one,0.0,0.0); txphase(one);
delay(tau_cpmg - 2.0/PI*pw_cp);
}
if(ncyc_cp > 2) {
delay(tau_cpmg);
rgpulse(2.0*pw_cp,one,0.0,0.0);
delay(tau_cpmg);
initval(ncyc_cp-2,v4);
loop(v4,v5);
delay(tau_cpmg);
rgpulse(2.0*pw_cp,one,0.0,0.0);
delay(tau_cpmg);
endloop(v5);
delay(tau_cpmg);
rgpulse(2.0*pw_cp,one,0.0,0.0); txphase(one);
delay(tau_cpmg - 2.0/PI*pw_cp);
}
rgpulse(pw_cp,zero,0.0,0.0);
delay(2.0e-6);
rgradient('z',gzlvl5);
delay(gt5);
rgradient('z',0.0);
delay(250.0e-6);
obspower(tpwr);
rgpulse(pw,zero,4.0e-6,0.0);
decpower(d_reb);
delay(2.0e-6);
rgradient('z',gzlvl6);
delay(gt6);
rgradient('z',0.0);
delay(150.0e-6);
delay(taua - POWER_DELAY - gt6 - 152e-6
- WFG2_START_DELAY - 0.5*pwc_reb);
simshaped_pulse("hard",sh_reb,2.0*pw,pwc_reb,zero,zero,0.0,0.0);
delay(taua - 0.5*pwc_reb - WFG2_STOP_DELAY - 2.0*POWER_DELAY - gt6 - 152e-6);
rlpower(dpwr,DODEV); /* Set power for decoupling */
rlpower(dpwr2,DO2DEV); /* Set power for decoupling */
delay(2.0e-6);
rgradient('z',gzlvl6);
delay(gt6);
rgradient('z',0.0);
delay(150.0e-6);
rgpulse(pw,zero,0.0,0.0);
/* rcvron(); */ /* Turn on receiver to warm up before acq */
/* BEGIN ACQUISITION */
status(D);
setreceiver(t5);
}
pulsesequence()
{
/* DECLARE AND LOAD VARIABLES */
int t1_counter; /* used for states tppi in t1 */
double tau1, /* t1 delay */
TC = getval("TC"), /* Constant delay 1/(JCC) ~ 13.5 ms */
mix = getval("mix"), /* TOCSY mixing time */
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
rf0, /* maximum fine power when using pwC pulses */
/* 90 degree pulse at Cab (46ppm), first off-resonance null at CO (174ppm) */
pwC1, /* 90 degree pulse length on C13 at rf1 */
rf1, /* fine power for 5.1 kHz rf for 600MHz magnet */
/* 180 degree pulse at Ca (46ppm), first off-resonance null at CO(174ppm) */
pwC2, /* 180 degree pulse length at rf2 */
rf2, /* fine power for 11.4 kHz rf for 600MHz magnet */
compC = getval("compC"), /* adjustment for C13 amplifier compression */
sw1 = getval("sw1"),
gt1 = getval("gt1"),
gzlvl1 = getval("gzlvl1"),
gt2 = getval("gt2"),
gzlvl2 = getval("gzlvl2"),
gstab = getval("gstab"),
ppm,
co_ofs = getval("co_ofs"), /* offset for C' */
co_bw = getval("co_bw"), /* bandwidth for C' */
copwr = getval("copwr"), /* power for C' decoupling. Get from CO_dec.DEC*/
codmf = getval("codmf"), /* dmf for C' decoupling. Get from CO_dec.DEC */
codres = getval("codres"), /* dres for C' decoupling. Get from CO_dec.DEC */
mixbw, /* band width for mixing shape */
mixpwr = getval("mixpwr"), /* power for CC mixing. Get from ccmix.DEC*/
mixdmf= getval("mixdmf"), /* dmf for CC decoupling. Get from ccmix.DEC */
mixdres = getval("mixdres"); /* dres for CC decoupling. Get from ccmix.DEC */
/* LOAD PHASE TABLE */
settable(t1,2,phi1);
settable(t2,1,phi2);
settable(t3,1,phi3);
settable(t12,2,rec);
setautocal(); /* activate auto-calibration */
/* INITIALIZE VARIABLES */
/* maximum fine power for pwC pulses */
rf0 = 4095.0;
/* 90 degree pulse on Cab, null at CO 128ppm away */
pwC1 = sqrt(15.0)/(4.0*128.0*sfrq);
rf1 = (compC*4095.0*pwC)/pwC1;
rf1 = (int) (rf1 + 0.5);
/* 180 degree pulse on Cab, null at CO 128ppm away */
pwC2 = sqrt(3.0)/(2.0*128.0*sfrq);
rf2 = (4095.0*compC*pwC*2.0)/pwC2;
rf2 = (int) (rf2 + 0.5);
if( rf2 > 4295 )
{ printf("increase pwClvl"); psg_abort(1);}
if(( rf2 > 4095 ) && (rf2 <4296)) rf2=4095;
/* CHECK VALIDITY OF PARAMETER RANGES */
if ( 0.5*ni*1/(sw1) > TC)
{ printf(" ni is too big. Make ni equal to %d or less.\n",
((int)((TC)*2.0*sw1))); psg_abort(1);}
/* PHASES AND INCREMENTED TIMES */
/* Phase incrementation for hypercomplex 2D data, States-Haberkorn element */
if (phase1 == 2) tsadd(t1,1,4);
tau1 = d2;
tau1 = tau1/2.0;
/* Calculate modifications to phases for States-TPPI acquisition */
if( ix == 1) d2_init = d2;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if(t1_counter % 2)
{ tsadd(t1,2,4); tsadd(t12,2,4); }
if (autocal[0] == 'y')
{
if(FIRST_FID)
{
ppm = getval("sfrq");
ofs_check(C13ofs);
co_ofs = (C13ofs+118.0)*ppm; co_bw = 20*ppm;
CO_dec = pbox_Dsh("CO_dec", "SEDUCE1", co_bw, co_ofs, pwC*compC, pwClvl);
copwr = CO_dec.pwr; codmf = CO_dec.dmf; codres = CO_dec.dres;
mixbw = sw1;
mix_seq = pbox_Dsh("mix_seq", "FLOPSY8", mixbw, 0.0, pwC*compC, pwClvl);
mixpwr = mix_seq.pwr; mixdmf = mix_seq.dmf; mixdres = mix_seq.dres;
}
}
/* BEGIN PULSE SEQUENCE */
status(A);
delay(d1);
if ( dm3[B] == 'y' )
{ lk_hold(); lk_sampling_off();} /*freezes z0 correction, stops lock pulsing*/
rcvroff();
obspower(pwClvl);
decpower(tpwr);
dec2power(dpwr2);
dec3power(dpwr3);
obspwrf(rf1); /*fine power for Cab 90 degree pulse */
obsoffset(tof); /*13C carrier at 46 ppm */
txphase(zero);
delay(1.0e-5);
status(B);
rgpulse(pwC1, t1, 0.0,0.0);
/* xxxxxxxxxxxxxxxxxxxxxx 13Cab Constant Time Evolution xxxxxxxxxxxxxxxxxx */
obspower(copwr); obspwrf(rf0); txphase(zero);
obsunblank();
xmtron();
obsprgon("CO_dec",1.0/codmf,codres);
if ( dm3[B] == 'y' ) /* turns on 2H decoupling */
{
dec3rgpulse(1/dmf3,one,10.0e-6,2.0e-6);
dec3unblank();
dec3phase(zero);
delay(2.0e-6);
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
delay(TC - tau1 - pwC2/2 - 1/dmf3);
}
else
delay(TC - tau1 - pwC2/2);
obsprgoff();
xmtroff();
obsblank();
obspower(pwClvl); obspwrf(rf2);
rgpulse(pwC2, zero, 0.0, 0.0);
obspower(copwr); obspwrf(rf0); txphase(zero);
obsunblank();
xmtron();
obsprgon("CO_dec",1.0/codmf,codres);
if ( dm3[B] == 'y' ) /* turns off 2H decoupling */
{
delay(TC + tau1 - pwC2/2 - 1/dmf3);
setstatus(DEC3ch, FALSE, 'c', FALSE, dmf3);
dec3rgpulse(1/dmf3,three,2.0e-6,2.0e-6);
dec3blank();
lk_autotrig(); /* resumes lock pulsing */
}
else
delay(TC + tau1 - pwC2/2);
obsprgoff();
xmtroff();
obsblank();
obspower(pwClvl); obspwrf(rf1);
rgpulse(pwC1,t2,0.0,0.0);
status(C);
zgradpulse(gzlvl1, gt1);
delay(gstab);
/* xxxxxxxxxxxxxxxxxxxxxxxxxxxx FLOPSY 8 Spin lock for mixing xxxxxxxxxxxxxxxxxxxx */
obspower(mixpwr); obspwrf(rf0); txphase(zero);
obsunblank();
xmtron();
obsprgon("mix_seq",1.0/mixdmf,mixdres);
delay(mix-gt1-gt2);
obsprgoff();
xmtroff();
obsblank();
obspower(pwClvl); obspwrf(rf1);
zgradpulse(gzlvl2,gt2);
delay(gstab);
rgpulse(pwC1,t3,0.0,rof2);
getelem(t3,ct,v3);
add(v3,one,v3);
obspower(pwClvl); obspwrf(rf0);
delay(350e-6-rof2);
rgpulse(pwC*2.0,v3,0.0,0.0);
delay(350e-6);
status(D);
setreceiver(t12);
}
pulsesequence()
{
/* DECLARE VARIABLES */
char fsat[MAXSTR],
fscuba[MAXSTR],
f1180[MAXSTR], /* Flag to start t1 @ halfdwell */
f2180[MAXSTR], /* Flag to start t2 @ halfdwell */
C_flg[MAXSTR],
dtt_flg[MAXSTR];
int phase, phase2, ni, ni2,
t1_counter, /* used for states tppi in t1 */
t2_counter; /* used for states tppi in t2 */
double tau1, /* t1 delay */
tau2, /* t2 delay */
taua, /* ~ 1/4JHC = 1.6 ms */
taub, /* 1/6JCH = 1.1 ms */
BigTC, /* Carbon constant time period = 1/4Jcc = 7.0 ms */
BigTC1, /* Carbon constant time period2 < 1/4Jcc to account for relaxation */
pwN, /* PW90 for 15N pulse @ pwNlvl */
pwC, /* PW90 for c nucleus @ pwClvl */
pwcrb180, /* PW180 for C 180 reburp @ rfrb */
pwClvl, /* power level for 13C pulses on dec1 */
compC, compH, /* compression factors for H1 and C13 amps */
rfrb, /* power level for 13C reburp pulse */
pwNlvl, /* high dec2 pwr for 15N hard pulses */
sw1, /* sweep width in f1 */
sw2, /* sweep width in f2 */
tofps, /* tof for presat */
gt0,
gt1,
gt2,
gt3,
gt4,
gstab,
gzlvl0,
gzlvl1,
gzlvl2,
gzlvl3,
gzlvl4,
decstep1,
bw, ofs, ppm,
pwd1,
dpwr3_D,
pwd,
tpwrs,
pwHs,
dof_me,
tof_dtt,
tpwrs1,
pwHs1,
dpwrsed,
pwsed,
dressed,
rfrb_cg,
pwrb_cg;
/* LOAD VARIABLES */
getstr("fsat",fsat);
getstr("f1180",f1180);
getstr("f2180",f2180);
getstr("fscuba",fscuba);
getstr("C_flg",C_flg);
getstr("dtt_flg",dtt_flg);
tofps = getval("tofps");
taua = getval("taua");
taub = getval("taub");
BigTC = getval("BigTC");
BigTC1 = getval("BigTC1");
pwC = getval("pwC");
pwcrb180 = getval("pwcrb180");
pwN = getval("pwN");
tpwr = getval("tpwr");
pwClvl = getval("pwClvl");
compC = getval("compC");
compH = getval("compH");
dpwr = getval("dpwr");
pwNlvl = getval("pwNlvl");
phase = (int) ( getval("phase") + 0.5);
phase2 = (int) ( getval("phase2") + 0.5);
sw1 = getval("sw1");
sw2 = getval("sw2");
ni = getval("ni");
ni2 = getval("ni2");
gt0 = getval("gt0");
gt1 = getval("gt1");
gt2 = getval("gt2");
gt3 = getval("gt3");
gt4 = getval("gt4");
gstab = getval("gstab");
gzlvl0 = getval("gzlvl0");
gzlvl1 = getval("gzlvl1");
gzlvl2 = getval("gzlvl2");
gzlvl3 = getval("gzlvl3");
gzlvl4 = getval("gzlvl4");
decstep1 = getval("decstep1");
pwd1 = getval("pwd1");
dpwr3_D = getval("dpwr3_D");
pwd = getval("pwd");
pwHs = getval("pwHs");
dof_me = getval("dof_me");
pwHs1 = pwHs;
tpwrs=-16.0; tpwrs1=tpwrs;
tof_dtt = getval("tof_dtt");
dpwrsed = -16;
pwsed = 1000.0;
dressed = 90.0;
pwrb_cg = 0.0;
setautocal(); /* activate auto-calibration */
if(FIRST_FID) /* make shapes */
{
ppm = getval("dfrq");
bw = 80.0*ppm;
rb180 = pbox_make("rb180P", "reburp", bw, 0.0, compC*pwC, pwClvl);
bw = 8.125*ppm; ofs = -24.0*ppm;
rb180_cg = pbox_make("rb180_cgP", "reburp", bw, ofs, compC*pwC, pwClvl);
bw = 20.0*ppm; ofs = 136.0*ppm;
cosed = pbox("COsedP", CODEC, CODECps, dfrq, compC*pwC, pwClvl);
if(taua < (gt4+106e-6+pwHs)) printf("gt4 or pwHs may be too long! ");
if(taub < rb180_cg.pw) printf("rb180_cgP pulse may be too long! ");
}
pwcrb180 = rb180.pw; rfrb = rb180.pwrf; /* set up parameters */
pwrb_cg = rb180_cg.pw; rfrb_cg = rb180_cg.pwrf; /* set up parameters */
tpwrs = tpwr - 20.0*log10(pwHs/((compH*pw)*1.69)); /* sinc=1.69xrect */
tpwrs = (int) (tpwrs); tpwrs1=tpwrs;
dpwrsed = cosed.pwr; pwsed = 1.0/cosed.dmf; dressed = cosed.dres;
/* LOAD PHASE TABLE */
settable(t1,2,phi1);
settable(t2,4,phi2);
settable(t3,4,phi3);
settable(t4,4,phi4);
settable(t5,8,phi5);
settable(t6,8,phi6);
settable(t7,8,phi7);
settable(t8,1,phi8);
settable(t9,2,rec);
/* CHECK VALIDITY OF PARAMETER RANGES */
if( BigTC - 0.5*(ni2-1)*1/(sw2) - WFG_STOP_DELAY - POWER_DELAY
- 4.0e-6
< 0.2e-6 )
{
printf(" ni2 is too big\n");
psg_abort(1);
}
if((dm[A] == 'y' || dm[B] == 'y' || dm[C] == 'y' ))
{
printf("incorrect dec1 decoupler flags! ");
psg_abort(1);
}
if((dm2[A] == 'y' || dm2[B] == 'y' || dm2[C] == 'y' || dm2[D] == 'y'))
{
printf("incorrect dec2 decoupler flags! Should be 'nnnn' ");
psg_abort(1);
}
if( satpwr > 6 )
{
printf("SATPWR too large !!! ");
psg_abort(1);
}
if( dpwr > 48 )
{
printf("don't fry the probe, DPWR too large! ");
psg_abort(1);
}
if( dpwr2 > -16 )
{
printf("don't fry the probe, DPWR2 too large! ");
psg_abort(1);
}
if( pw > 200.0e-6 )
{
printf("dont fry the probe, pw too high ! ");
psg_abort(1);
}
if( pwN > 200.0e-6 )
{
printf("dont fry the probe, pwN too high ! ");
psg_abort(1);
}
if( pwC > 200.0e-6 )
{
printf("dont fry the probe, pwC too high ! ");
psg_abort(1);
}
if( pwcrb180 > 500.0e-6 )
{
printf("dont fry the probe, pwcrb180 too high ! ");
psg_abort(1);
}
if(dpwr3 > 51)
{
printf("dpwr3 is too high; < 52\n");
psg_abort(1);
}
if(dpwr3_D > 49)
{
printf("dpwr3_D is too high; < 50\n");
psg_abort(1);
}
if(d1 < 1)
{
printf("d1 must be > 1\n");
psg_abort(1);
}
if(dpwrsed > 48)
{
printf("dpwrsed must be less than 49\n");
psg_abort(1);
}
if( gt0 > 5.0e-3 || gt1 > 5.0e-3 || gt2 > 5.0e-3 ||
gt3 > 5.0e-3 || gt4 > 5.0e-3 )
{ printf(" all values of gti must be < 5.0e-3\n");
psg_abort(1);
}
if(ix==1) {
printf("make sure that BigTC1 is set properly for your application\n");
printf("7 ms, neglecting relaxation \n");
}
/* Phase incrementation for hypercomplex 2D data */
if (phase == 2) {
tsadd(t1,1,4);
tsadd(t2,1,4);
tsadd(t3,1,4);
tsadd(t4,1,4);
}
if (phase2 == 2)
tsadd(t8,1,4);
/* Set up f1180 tau1 = t1 */
tau1 = d2;
tau1 = tau1 - 2.0*pw - 4.0/PI*pwC - POWER_DELAY - 2.0e-6 - PRG_START_DELAY
- PRG_STOP_DELAY - POWER_DELAY - 2.0e-6;
if(f1180[A] == 'y') {
tau1 += ( 1.0 / (2.0*sw1) );
if(tau1 < 0.4e-6) tau1 = 4.0e-7;
}
tau1 = tau1/2.0;
/* Set up f2180 tau2 = t2 */
tau2 = d3;
if(f2180[A] == 'y') {
tau2 += ( 1.0 / (2.0*sw2) );
if(tau2 < 0.4e-6) tau2 = 4.0e-7;
}
tau2 = tau2/2.0;
/* Calculate modifications to phases for States-TPPI acquisition */
if( ix == 1) d2_init = d2 ;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if(t1_counter % 2) {
tsadd(t1,2,4);
tsadd(t9,2,4);
}
if( ix == 1) d3_init = d3 ;
t2_counter = (int) ( (d3-d3_init)*sw2 + 0.5 );
if(t2_counter % 2) {
tsadd(t8,2,4);
tsadd(t9,2,4);
}
/* BEGIN ACTUAL PULSE SEQUENCE */
status(A);
obspower(satpwr); /* Set transmitter power for 1H presaturation */
decpower(pwClvl); /* Set Dec1 power for hard 13C pulses */
dec2power(pwNlvl); /* Set Dec2 to low power */
/* Presaturation Period */
status(B);
if (fsat[0] == 'y')
{
obsoffset(tofps);
delay(2.0e-5);
rgpulse(d1,zero,2.0e-6,2.0e-6); /* presat with transmitter */
obspower(tpwr); /* Set transmitter power for hard 1H pulses */
delay(2.0e-5);
if(fscuba[0] == 'y')
{
delay(2.2e-2);
rgpulse(pw,zero,2.0e-6,0.0);
rgpulse(2.0*pw,one,2.0e-6,0.0);
rgpulse(pw,zero,2.0e-6,0.0);
delay(2.2e-2);
}
}
else
{
delay(d1);
}
obspower(tpwr); /* Set transmitter power for hard 1H pulses */
obsoffset(tof);
txphase(t1);
decphase(zero);
dec2phase(zero);
delay(1.0e-5);
/* Begin Pulses */
status(C);
decoffset(dof_me);
lk_hold();
rcvroff();
delay(20.0e-6);
/* ensure that magnetization originates on 1H and not 13C */
if(dtt_flg[A] == 'y') {
obsoffset(tof_dtt);
obspower(tpwrs1);
shaped_pulse("H2Osinc",pwHs1,zero,10.0e-6,0.0);
obspower(tpwr);
obsoffset(tof);
}
decrgpulse(pwC,zero,0.0,0.0);
zgradpulse(gzlvl0,gt0);
delay(gstab);
rgpulse(pw,zero,0.0,0.0); /* 90 deg 1H pulse */
zgradpulse(gzlvl1,gt1);
delay(gstab);
delay(taua - gt1 -gstab);
simpulse(2.0*pw,2.0*pwC,zero,zero,0.0,0.0);
txphase(one);
delay(taua - gt1 - gstab);
zgradpulse(gzlvl1,gt1);
delay(gstab);
rgpulse(pw,one,0.0,0.0);
/* shaped_pulse */
obspower(tpwrs);
shaped_pulse("H2Osinc",pwHs,zero,2.0e-6,0.0);
obspower(tpwr);
/* shaped_pulse */
decoffset(dof); /* jump 13C to 40 ppm */
zgradpulse(gzlvl2,gt2);
delay(gstab);
decrgpulse(pwC,t1,4.0e-6,0.0); decphase(zero);
initval(1.0,v3);
decstepsize(decstep1);
dcplrphase(v3);
decpwrf(rfrb);
delay(BigTC - POWER_DELAY - WFG_START_DELAY);
decshaped_pulse(rb180.name,pwcrb180,zero,0.0,0.0);
dcplrphase(zero);
decphase(t2);
decpwrf(4095.0);
delay(BigTC - WFG_STOP_DELAY - POWER_DELAY);
decrgpulse(pwC,t2,0.0,0.0);
decphase(zero);
/* turn on 2H decoupling */
dec3phase(one);
dec3power(dpwr3);
dec3rgpulse(pwd1,one,4.0e-6,0.0);
dec3phase(zero);
dec3unblank();
dec3power(dpwr3_D);
dec3prgon(dseq3,pwd,dres3);
dec3on();
/* turn on 2H decoupling */
initval(1.0,v3);
decstepsize(decstep1);
dcplrphase(v3);
decpwrf(rfrb);
delay(BigTC1 - POWER_DELAY - 4.0e-6 - pwd1
- POWER_DELAY - PRG_START_DELAY - POWER_DELAY - WFG_START_DELAY);
decshaped_pulse(rb180.name,pwcrb180,zero,0.0,0.0);
dcplrphase(zero);
decphase(t3);
decpwrf(4095.0);
delay(BigTC1 - WFG_STOP_DELAY - POWER_DELAY);
decrgpulse(pwC,t3,0.0,0.0);
decpwrf(rfrb_cg); decphase(zero);
if(taub > pwrb_cg)
delay(taub/2.0 - pwrb_cg/2.0 - POWER_DELAY - WFG_START_DELAY);
decshaped_pulse(rb180_cg.name,pwrb_cg,zero,0.0,0.0);
decpwrf(rfrb);
if(taub > pwrb_cg)
delay(taub/2.0 - pwrb_cg/2.0 - WFG_STOP_DELAY - POWER_DELAY - SAPS_DELAY
- 2.0e-6 - WFG_START_DELAY);
initval(1.0,v3);
decstepsize(decstep1);
dcplrphase(v3);
decshaped_pulse(rb180.name,pwcrb180,zero,2.0e-6,0.0);
dcplrphase(zero);
decpwrf(rfrb_cg); decphase(zero);
if(taub > pwrb_cg)
delay(taub/2.0 - pwrb_cg/2.0 - WFG_STOP_DELAY - SAPS_DELAY
- POWER_DELAY - WFG_START_DELAY);
decshaped_pulse(rb180_cg.name,pwrb_cg,zero,0.0,0.0);
decpwrf(4095.0); decphase(t4);
if(taub > pwrb_cg)
delay(taub/2.0 - pwrb_cg/2.0 - WFG_STOP_DELAY - POWER_DELAY);
decrgpulse(pwC,t4,0.0,0.0);
if(C_flg[A] == 'n') {
decpower(dpwrsed); decunblank(); decphase(zero); delay(2.0e-6);
decprgon(cosed.name,pwsed,dressed);
decon();
delay(tau1);
rgpulse(2.0*pw,zero,0.0,0.0);
delay(tau1);
decoff();
decprgoff();
decblank();
decpower(pwClvl);
}
else
simpulse(2.0*pw,2.0*pwC,zero,zero,4.0e-6,4.0e-6);
decrgpulse(pwC,t5,2.0e-6,0.0);
decpwrf(rfrb_cg); decphase(zero);
if(taub > pwrb_cg)
delay(taub/2.0 - pwrb_cg/2.0 - POWER_DELAY - WFG_START_DELAY);
decshaped_pulse(rb180_cg.name,pwrb_cg,zero,0.0,0.0);
decpwrf(rfrb);
if(taub > pwrb_cg)
delay(taub/2.0 - pwrb_cg/2.0 - WFG_STOP_DELAY - POWER_DELAY - SAPS_DELAY
- 2.0e-6 - WFG_START_DELAY);
initval(1.0,v3);
decstepsize(decstep1);
dcplrphase(v3);
decshaped_pulse(rb180.name,pwcrb180,zero,2.0e-6,0.0);
dcplrphase(zero);
decpwrf(rfrb_cg); decphase(zero);
if(taub > pwrb_cg)
delay(taub/2.0 - pwrb_cg/2.0 - WFG_STOP_DELAY - SAPS_DELAY
- POWER_DELAY - WFG_START_DELAY);
decshaped_pulse(rb180_cg.name,pwrb_cg,zero,0.0,0.0);
decpwrf(4095.0); decphase(t6);
if(taub > pwrb_cg)
delay(taub/2.0 - pwrb_cg/2.0 - WFG_STOP_DELAY - POWER_DELAY);
decrgpulse(pwC,t6,0.0,0.0);
decphase(zero);
initval(1.0,v3);
decstepsize(decstep1);
dcplrphase(v3);
decpwrf(rfrb);
delay(BigTC1 - POWER_DELAY - WFG_START_DELAY);
decshaped_pulse(rb180.name,pwcrb180,zero,0.0,0.0);
dcplrphase(zero);
decphase(t7);
decpwrf(4095.0);
delay(BigTC1 - WFG_STOP_DELAY - POWER_DELAY
- PRG_STOP_DELAY - POWER_DELAY - 4.0e-6 - pwd1);
/* 2H decoupling off */
dec3off();
dec3prgoff();
dec3blank();
dec3power(dpwr3);
dec3rgpulse(pwd1,three,4.0e-6,0.0);
/* 2H decoupling off */
decrgpulse(pwC,t7,0.0,0.0);
decphase(zero);
delay(tau2);
rgpulse(2.0*pw,zero,0.0,0.0);
initval(1.0,v3);
decstepsize(decstep1);
dcplrphase(v3);
decpwrf(rfrb);
delay(BigTC - 2.0*pw - POWER_DELAY - WFG_START_DELAY);
decshaped_pulse(rb180.name,pwcrb180,zero,0.0,0.0);
dcplrphase(zero);
decphase(t8);
decpwrf(4095.0);
delay(BigTC - tau2 - WFG_STOP_DELAY - POWER_DELAY - 4.0e-6);
decrgpulse(pwC,t8,4.0e-6,0.0);
decoffset(dof_me);
zgradpulse(gzlvl3,gt3);
delay(gstab);
lk_sample();
/* shaped_pulse */
obspower(tpwrs);
shaped_pulse("H2Osinc",pwHs,two,2.0e-6,0.0);
obspower(tpwr);
/* shaped_pulse */
rgpulse(pw,zero,4.0e-6,0.0);
zgradpulse(gzlvl4,gt4);
delay(gstab);
delay(taua - gt4 -gstab
- POWER_DELAY - 2.0e-6 - WFG_START_DELAY
- pwHs - WFG_STOP_DELAY - POWER_DELAY - 2.0e-6);
/* shaped_pulse */
obspower(tpwrs);
shaped_pulse("H2Osinc",pwHs,two,2.0e-6,0.0);
obspower(tpwr);
/* shaped_pulse */
simpulse(2.0*pw,2.0*pwC,zero,zero,2.0e-6,0.0);
/* shaped_pulse */
obspower(tpwrs);
shaped_pulse("H2Osinc",pwHs,two,2.0e-6,0.0);
obspower(tpwr);
/* shaped_pulse */
zgradpulse(gzlvl4,gt4);
delay(gstab);
delay(taua - POWER_DELAY - WFG_START_DELAY
- pwHs - WFG_STOP_DELAY - POWER_DELAY
- gt4 - gstab - 2.0*POWER_DELAY);
decpower(dpwr); /* Set power for decoupling */
dec2power(dpwr2);
/* rcvron(); */ /* Turn on receiver to warm up before acq */
/* BEGIN ACQUISITION */
status(D);
setreceiver(t9);
}
pulsesequence()
{
/* DECLARE AND LOAD VARIABLES; parameters used in the last half of the */
/* sequence are declared and initialized as 0.0 in bionmr.h, and */
/* reinitialized below */
char f1180[MAXSTR], /* Flag to start t1 @ halfdwell */
f2180[MAXSTR], /* Flag to start t2 @ halfdwell */
COrefoc[MAXSTR],
TROSY[MAXSTR]; /* do TROSY on N15 and H1 */
int t1_counter, /* used for states tppi in t1 */
t2_counter, /* used for states tppi in t2 */
ni2 = getval("ni2");
double d2_init=0.0, /* used for states tppi in t1 */
d3_init=0.0, /* used for states tppi in t2 */
tau1, /* t1 delay */
timeTN = getval("timeTN"), /* constant time for 15N evolution */
timeNCA = getval("timeNCA"),
timeC = getval("timeC"),
lambda = 1.0/(4.0*getval("JNH")),
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
pwS1, /* length of square 90 on Ca */
phshift, /* phase shift induced on Ca by 180 on CO in middle of t1 */
pwS2, /* length of 180 on CO */
pwS = getval("pwS"), /* used to change 180 on CO in t1 for 1D calibrations */
pwZ, /* the largest of pwS2 and 2.0*pwN */
pwZ1, /* the largest of pwS2 and 2.0*pwN for 1D experiments */
pwNlvl = getval("pwNlvl"), /* power for N15 pulses */
pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */
sw1 = getval("sw1"),
sw2 = getval("sw2"),
gt0 = getval("gt0"), /* other gradients */
gt3 = getval("gt3"),
gzlvl0 = getval("gzlvl0"),
gzlvl3 = getval("gzlvl3");
getstr("f1180",f1180);
getstr("f2180",f2180);
getstr("COrefoc",COrefoc);
getstr("TROSY",TROSY);
/* LOAD PHASE TABLE */
settable(t3,2,phi3);
settable(t4,1,phx);
settable(t5,4,phi5);
if (TROSY[A]=='y')
{settable(t8,1,phy);
settable(t9,1,phx);
settable(t10,1,phy);
settable(t11,1,phx);
settable(t12,4,recT);}
else
{settable(t8,1,phx);
settable(t9,8,phi9);
settable(t10,1,phx);
settable(t11,1,phy);
settable(t12,4,rec);}
/* INITIALIZE VARIABLES */
kappa = 5.4e-3;
pwHs = 1.7e-3*500.0/sfrq; /* length of H2O flipback, 1.7ms at 500 MHz*/
widthHd = 34.0; /* bandwidth of H1 WALTZ16 decoupling, 7.3 kHz at 600 MHz */
pwHd = h1dec90pw("WALTZ16", widthHd, 0.0); /* H1 90 length for WALTZ16 */
/* get calculated pulse lengths of shaped C13 pulses */
pwS1 = c13pulsepw("co", "ca", "sinc", 90.0);
pwS2 = c13pulsepw("ca", "co", "square", 180.0);
/* get calculated pulse lengths of shaped C13 pulses
pwS1 = c13pulsepw("ca", "co", "square", 90.0);
pwS2 = c13pulsepw("co", "ca", "sinc", 180.0); */
/* the 180 pulse on CO at the middle of t1 */
if ((ni2 > 0.0) && (ni == 1.0)) ni = 0.0;
if (pwS2 > 2.0*pwN) pwZ = pwS2; else pwZ = 2.0*pwN;
if ((pwS==0.0) && (pwS2>2.0*pwN)) pwZ1=pwS2-2.0*pwN; else pwZ1=0.0;
if ( ni > 1 ) pwS = 180.0;
if ( pwS > 0 ) phshift = 130.0;
else phshift = 130.0;
/* CHECK VALIDITY OF PARAMETER RANGES */
if ( 0.5*ni2*1/(sw2) > timeTN - WFG3_START_DELAY)
{ printf(" ni2 is too big. Make ni2 equal to %d or less.\n",
((int)((timeTN - WFG3_START_DELAY)*2.0*sw2))); psg_abort(1);}
if ( dm[A] == 'y' || dm[B] == 'y' || dm[C] == 'y' )
{ printf("incorrect dec1 decoupler flags! Should be 'nnn' "); psg_abort(1);}
if ( dm2[A] == 'y' || dm2[B] == 'y' )
{ printf("incorrect dec2 decoupler flags! Should be 'nny' "); psg_abort(1);}
if ( dm3[A] == 'y' || dm3[C] == 'y' )
{ printf("incorrect dec3 decoupler flags! Should be 'nyn' or 'nnn' ");
psg_abort(1);}
if ( dpwr2 > 46 )
{ printf("dpwr2 too large! recheck value "); psg_abort(1);}
if ( pw > 20.0e-6 )
{ printf(" pw too long ! recheck value "); psg_abort(1);}
if ( pwN > 100.0e-6 )
{ printf(" pwN too long! recheck value "); psg_abort(1);}
if ( TROSY[A]=='y' && dm2[C] == 'y')
{ text_error("Choose either TROSY='n' or dm2='n' ! "); psg_abort(1);}
/* PHASES AND INCREMENTED TIMES */
/* Phase incrementation for hypercomplex 2D data, States-Haberkorn element */
if (phase1 == 2) tsadd(t3,1,4);
if (TROSY[A]=='y')
{ if (phase2 == 2) icosel = +1;
else {tsadd(t4,2,4); tsadd(t10,2,4); icosel = -1;}
}
else { if (phase2 == 2) {tsadd(t10,2,4); icosel = +1;}
else icosel = -1;
}
/* Set up f1180 */
tau1 = d2;
if((f1180[A] == 'y') && (ni > 1.0))
{ tau1 += ( 1.0 / (2.0*sw1) ); if(tau1 < 0.2e-6) tau1 = 0.0; }
tau1 = tau1/2.0;
/* Set up f2180 */
tau2 = d3;
if((f2180[A] == 'y') && (ni2 > 1.0))
{ tau2 += ( 1.0 / (2.0*sw2) ); if(tau2 < 0.2e-6) tau2 = 0.0; }
tau2 = tau2/2.0;
/* Calculate modifications to phases for States-TPPI acquisition */
if( ix == 1) d2_init = d2;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if(t1_counter % 2)
{ tsadd(t3,2,4); tsadd(t12,2,4); }
if( ix == 1) d3_init = d3;
t2_counter = (int) ( (d3-d3_init)*sw2 + 0.5 );
if(t2_counter % 2)
{ tsadd(t8,2,4); tsadd(t12,2,4); }
/* BEGIN PULSE SEQUENCE */
status(A);
delay(d1);
if (dm3[B]=='y') lk_hold();
rcvroff();
set_c13offset("co");
obsoffset(tof);
obspower(tpwr);
obspwrf(4095.0);
decpower(pwClvl);
decpwrf(4095.0);
dec2power(pwNlvl);
txphase(zero);
delay(1.0e-5);
dec2rgpulse(pwN, zero, 0.0, 0.0); /*destroy N15 and C13 magnetization*/
decrgpulse(pwC, zero, 0.0, 0.0);
zgradpulse(gzlvl0, 0.5e-3);
delay(1.0e-4);
dec2rgpulse(pwN, one, 0.0, 0.0);
decrgpulse(pwC, zero, 0.0, 0.0);
zgradpulse(0.7*gzlvl0, 0.5e-3);
delay(5.0e-4);
rgpulse(pw,zero,0.0,0.0); /* 1H pulse excitation */
dec2phase(zero);
zgradpulse(gzlvl0, gt0);
delay(lambda - gt0);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
txphase(one);
zgradpulse(gzlvl0, gt0);
delay(lambda - gt0);
rgpulse(pw, one, 0.0, 0.0);
if (TROSY[A]=='y')
{txphase(two);
shiftedpulse("sinc", pwHs, 90.0, 0.0, two, 2.0e-6, 0.0);
zgradpulse(gzlvl3, gt3);
delay(2.0e-4);
dec2rgpulse(pwN, zero, 0.0, 0.0);
delay(0.5*kappa - 2.0*pw);
rgpulse(2.0*pw, two, 0.0, 0.0);
decphase(zero);
dec2phase(zero);
delay(timeTN - 0.5*kappa - WFG3_START_DELAY);
}
else
{txphase(zero);
shiftedpulse("sinc", pwHs, 90.0, 0.0, zero, 2.0e-6, 0.0);
zgradpulse(gzlvl3, gt3);
delay(2.0e-4);
dec2rgpulse(pwN, zero, 0.0, 0.0);
delay(kappa - POWER_DELAY - PWRF_DELAY - pwHd - 4.0e-6 - PRG_START_DELAY);
/* delays for h1waltzon subtracted */
h1waltzon("WALTZ16", widthHd, 0.0);
decphase(zero);
dec2phase(zero);
delay(timeTN - kappa - WFG3_START_DELAY);
}
c13pulse("co", "ca", "sinc", 180.0, zero, 0.0, 0.0); /* pwS2 */
delay(timeNCA - timeTN - timeC);
dec2rgpulse(2.0*pwN,zero,0.0,0.0);
c13pulse("ca", "co", "sinc", 180.0, zero, 0.0, 0.0);
decphase(zero);
delay(timeNCA - timeC + 1.3*pwN);
c13pulse("co", "ca", "sinc", 90.0, zero, 0.0, 0.0); /* pwS1 */
delay(timeC);
c13pulse("ca", "co", "square", 180.0, zero, 2.0e-6, 2.0e-6);
sim3_c13pulse("", "co", "ca", "sinc", "", 0.0, 180.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0); /* pwS2 */
delay(timeC);
c13pulse("ca", "co", "square", 180.0, zero, 2.0e-6, 2.0e-6);
c13pulse("co", "ca", "sinc", 90.0, one, 0.0, 0.0); /* pwS1 */
dec2rgpulse(pwN, zero, 0.0, 0.0);
if (TROSY[A]=='n') h1waltzoff("WALTZ16", widthHd, 0.0);
zgradpulse(gzlvl3, gt3);
delay(2.0e-4);
if(dm3[B] == 'y') /*optional 2H decoupling on */
{dec3unblank(); dec3rgpulse(1/dmf3, one, 0.0, 0.0);
dec3unblank(); setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);}
h1waltzon("WALTZ16", widthHd, 0.0);
/* xxxxxxxxxxxxxxxxxxxxxx 13Ca EVOLUTION xxxxxxxxxxxxxxxxxx */
set_c13offset("ca");
c13pulse("ca", "co", "square", 90.0, t3, 2.0e-6, 0.0); /* pwS1 */
decphase(zero);
if ((ni>1.0) && (tau1>0.0)) /* total 13C evolution equals d2 exactly */
{
/* 2.0*pwS1/PI compensates for evolution at 64% rate during 90 */
if (tau1 - 2.0*pwS1/PI - WFG3_START_DELAY - 0.5*pwZ - 2.0e-6
- 2.0*PWRF_DELAY - 2.0*POWER_DELAY > 0.0)
{
delay(tau1 - 2.0*pwS1/PI - WFG3_START_DELAY - 0.5*pwZ - 2.0e-6 - 2.0*PWRF_DELAY - 2.0*POWER_DELAY);
sim3_c13pulse("", "co", "ca", "sinc", "", 0.0, 180.0, 2.0*pwN,zero, zero, zero, 2.0e-6, 0.0);
initval(phshift, v3);
decstepsize(1.0);
dcplrphase(v3);
delay(tau1 - 2.0*pwS1/PI - SAPS_DELAY - 0.5*pwZ - WFG_START_DELAY - 2.0e-6 - 2.0*PWRF_DELAY - 2.0*POWER_DELAY);
}
else
{
initval(180.0, v3);
decstepsize(1.0);
dcplrphase(v3);
delay(2.0*tau1 - 4.0*pwS1/PI - SAPS_DELAY - WFG_START_DELAY - 2.0e-6 - PWRF_DELAY - POWER_DELAY);
}
/* delay(tau1);
sim3_c13pulse("", "co", "ca", "sinc", "", 0.0, 180.0, 2.0*pwN,zero, zero, zero, 2.0e-6, 0.0);
delay(tau1);
c13pulse("ca", "co", "square", 180.0, zero, 2.0e-6, 0.0);
sim3_c13pulse("", "co", "ca", "sinc", "", 0.0, 180.0, 2.0*pwN,zero, zero, zero, 2.0e-6, 0.0);*/
}
else if (ni==1.0)
{
delay(10.0e-6 + SAPS_DELAY + 0.5*pwZ1 + WFG_START_DELAY);
sim3_c13pulse("", "co", "ca", "sinc", "", 0.0, pwS, 2.0*pwN, zero, zero, zero, 2.0e-6, 0.0);
initval(phshift, v3);
decstepsize(1.0);
dcplrphase(v3);
delay(10.0e-6 + WFG3_START_DELAY + 0.5*pwZ1);
}
else
{
delay(10.0e-6);
c13pulse("ca", "co", "square", 180.0, zero, 2.0e-6, 0.0);
delay(10.0e-6);
/* delay(tau1);
sim3_c13pulse("", "co", "ca", "sinc", "", 0.0, 180.0, 2.0*pwN,zero, zero, zero, 2.0e-6, 0.0);
delay(tau1);
c13pulse("ca", "co", "square", 180.0, zero, 2.0e-6, 0.0);
sim3_c13pulse("", "co", "ca", "sinc", "", 0.0, 180.0, 2.0*pwN,zero, zero, zero, 2.0e-6, 0.0); */
}
decphase(t5);
c13pulse("ca", "co", "square", 90.0, t5, 2.0e-6, 0.0); /* pwS1 */
h1waltzoff("WALTZ16", widthHd, 0.0);
if(dm3[B] == 'y') /*optional 2H decoupling off */
{dec3rgpulse(1/dmf3, three, 0.0, 0.0); dec3blank();
setstatus(DEC3ch, FALSE, 'w', FALSE, dmf3); dec3blank();}
set_c13offset("co");
/* xxxxxxxxxxxxxxxxxxxx N15 EVOLUTION & SE TRAIN xxxxxxxxxxxxxxxxxxxxxxx */
ihn_evol_se_train("co", "ca"); /* common part of sequence in bionmr.h */
if (dm3[B] == 'y') lk_sample();
}
pulsesequence() {
// Define Variables and Objects and Get Parameter Values
DSEQ dec = getdseq("H");
strncpy(dec.t.ch,"dec",3);
putCmd("chHtppm='dec'\n");
strncpy(dec.s.ch,"dec",3);
putCmd("chHspinal='dec'\n");
DSEQ dec2 = getdseq("Y");
strncpy(dec2.t.ch,"dec2",3);
putCmd("chYtppm='dec2'\n");
strncpy(dec2.s.ch,"dec2",3);
putCmd("chYspinal='dec2'\n");
//--------------------------------------
// Copy Current Parameters to Processed
//-------------------------------------
putCmd("groupcopy('current','processed','acquisition')");
// Dutycycle Protection
DUTY d = init_dutycycle();
d.dutyon = getval("pwX90");
d.dutyoff = d1 + 4.0e-6;
d.c1 = d.c1 + (!strcmp(dec.seq,"tppm"));
d.c1 = d.c1 + ((!strcmp(dec.seq,"tppm")) && (dec.t.a > 0.0));
d.t1 = getval("rd") + getval("ad") + at;
d.c2 = d.c2 + (!strcmp(dec.seq,"spinal"));
d.c2 = d.c2 + ((!strcmp(dec.seq,"spinal")) && (dec.s.a > 0.0));
d.t2 = getval("rd") + getval("ad") + at;
if ((d.c1 == -1) && (d.c2 == -1)) {
d.c1 = ((!strcmp(dec2.seq,"tppm")) && (dec2.t.a == 0.0));
d.t1 = getval("rd") + getval("ad") + at;
d.c2 = ((!strcmp(dec2.seq,"spinal")) && (dec2.s.a == 0.0));
d.t2 = getval("rd") + getval("ad") + at;
}
d = update_dutycycle(d);
abort_dutycycle(d,10.0);
// Set Phase Tables
settable(phX90,4,table1);
settable(phRec,4,table2);
setreceiver(phRec);
// Begin Sequence
txphase(phX90); decphase(zero); dec2phase(zero);
obspwrf(getval("aX90"));
obsunblank(); decunblank(); _unblank34();
delay(d1);
sp1on(); delay(2.0e-6); sp1off(); delay(2.0e-6);
// X Direct Polarization
rgpulse(getval("pwX90"),phX90,0.0,0.0);
// Begin Acquisition
_dseqon(dec);
if (NUMch > 2) _dseqon(dec2);
if (NUMch > 3) dec3blank();
obsblank();
delay(getval("rd"));
startacq(getval("ad"));
acquire(np, 1/sw);
endacq();
_dseqoff(dec);
if (NUMch > 2) _dseqoff(dec2);
if (NUMch > 3) dec3unblank();
obsunblank(); decunblank();
}
void pulsesequence()
{
/* DECLARE AND LOAD VARIABLES */
char f1180[MAXSTR], /* Flag to start t1 @ halfdwell */
f2180[MAXSTR], /* Flag to start t2 @ halfdwell */
mag_flg[MAXSTR], /* magic-angle coherence transfer gradients */
TROSY[MAXSTR]; /* do TROSY on N15 and H1 */
int icosel, /* used to get n and p type */
t1_counter, /* used for states tppi in t1 */
t2_counter, /* used for states tppi in t2 */
PRexp, /* projection-reconstruction flag */
ni = getval("ni"),
ni2 = getval("ni2");
double tau1, /* t1 delay */
tau2, /* t2 delay */
tauCH = getval("tauCH"), /* 1/4J delay for CH */
zeta = getval("zeta"), /* zeta delay, 0.006 for 1D, 0.011 for 2D*/
timeTN = getval("timeTN"), /* constant time for 15N evolution */
timeCH = 1.1e-3, /* other delays */
timeAB = 3.3e-3,
kappa = 5.4e-3,
lambda = 2.4e-3,
csa, sna,
pra = M_PI*getval("pra")/180.0,
bw, ofs, ppm, /* temporary Pbox parameters */
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
rf0, /* maximum fine power when using pwC pulses */
/* 90 degree pulse at Cab(46ppm), first off-resonance null at CO (174ppm) */
pwC1, /* 90 degree pulse length on C13 at rf1 */
rf1, /* fine power for 5.1 kHz rf for 600MHz magnet */
/* 180 degree pulse at Cab(46ppm), first off-resonance null at CO(174ppm) */
pwC2, /* 180 degree pulse length at rf2 */
rf2, /* fine power for 11.4 kHz rf for 600MHz magnet */
/* the following pulse lengths for SLP pulses are automatically calculated */
/* by the macro "biocal". SLP pulse shapes, "offC7" etc are called */
/* directly from your shapelib. */
pwC7, /* 180 degree selective sinc pulse on CO(174ppm) */
rf7, /* fine power for the pwC7 ("offC7") pulse */
compH = getval("compH"), /* adjustment for C13 amplifier compression */
compC = getval("compC"), /* adjustment for C13 amplifier compression */
pwH, /* H1 90 degree pulse length at tpwr1 */
tpwr1, /* 9.2 kHz rf magnet for DIPSI-2 */
DIPSI2time, /* total length of DIPSI-2 decoupling */
ncyc_dec,
waltzB1=getval("waltzB1"),
pwNlvl = getval("pwNlvl"), /* power for N15 pulses */
pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */
sw1 = getval("sw1"),
sw2 = getval("sw2"),
gt1 = getval("gt1"), /* coherence pathway gradients */
gzcal = getval("gzcal"), /* g/cm to DAC conversion factor */
gzlvl1 = getval("gzlvl1"),
gzlvl2 = getval("gzlvl2"),
gt0 = getval("gt0"), /* other gradients */
gt3 = getval("gt3"),
gt4 = getval("gt4"),
gt5 = getval("gt5"),
gstab = getval("gstab"),
gzlvl0 = getval("gzlvl0"),
gzlvl3 = getval("gzlvl3"),
gzlvl4 = getval("gzlvl4"),
gzlvl5 = getval("gzlvl5"),
gzlvl6 = getval("gzlvl6");
getstr("f1180",f1180);
getstr("f2180",f2180);
getstr("mag_flg",mag_flg);
getstr("TROSY",TROSY);
csa = cos(pra);
sna = sin(pra);
/* LOAD PHASE TABLE */
settable(t3,1,phx);
settable(t4,1,phx);
if (TROSY[A]=='y')
{settable(t8,2,phi8T);
settable(t9,1,phx);
settable(t10,1,phy);
settable(t11,1,phx);
settable(t12,2,recT);}
else
{settable(t8,2,phi8);
settable(t9,8,phi9);
settable(t10,1,phx);
settable(t11,1,phy);
settable(t12,4,rec);}
/* INITIALIZE VARIABLES */
if( dpwrf < 4095 )
{ printf("reset dpwrf=4095 and recalibrate C13 90 degree pulse");
psg_abort(1); }
/* set zeta to 6ms for 1D spectral check, otherwise it will be the */
/* value in the dg2 parameter set (about 11ms) for 2D/13C and 3D work */
if (ni>1) zeta = zeta;
else zeta = 0.006;
/* maximum fine power for pwC pulses */
rf0 = 4095.0;
setautocal(); /* activate auto-calibration flags */
if (autocal[0] == 'n')
{
/* 90 degree pulse on Cab, null at CO 128ppm away */
pwC1 = sqrt(15.0)/(4.0*128.0*dfrq);
rf1 = 4095.0*(compC*pwC/pwC1);
rf1 = (int) (rf1 + 0.5);
/* 180 degree pulse on Cab, null at CO 128ppm away */
pwC2 = sqrt(3.0)/(2.0*128.0*dfrq);
rf2 = (4095.0*compC*pwC*2.0)/pwC2;
rf2 = (int) (rf2 + 0.5);
if( rf2 > 4295 )
{ printf("increase pwClvl"); psg_abort(1);}
if(( rf2 < 4296 ) && (rf2>4095)) rf2=4095;
/* 180 degree one-lobe sinc pulse on CO, null at Ca 118m away */
pwC7 = getval("pwC7");
rf7 = (compC*4095.0*pwC*2.0*1.65)/pwC7; /* needs 1.65 times more */
rf7 = (int) (rf7 + 0.5); /* power than a square pulse */
}
else /* if autocal = 'y'(yes), 'q'(quiet), r(read), or 's'(semi) */
{
if(FIRST_FID) /* call Pbox */
{
ppm = getval("dfrq");
bw = 128.0*ppm; ofs = bw;
offC1 = pbox_Rcal("square90n", bw, compC*pwC, pwClvl);
offC2 = pbox_Rcal("square180n", bw, compC*pwC, pwClvl);
bw = 118.0*ppm;
offC7 = pbox_make("offC7", "sinc180n", bw, ofs, compC*pwC, pwClvl);
if (dm3[B] == 'y') H2ofs = 3.2;
ofs_check(H1ofs, C13ofs, N15ofs, H2ofs);
}
pwC1 = offC1.pw; rf1 = offC1.pwrf;
pwC2 = offC2.pw; rf2 = offC2.pwrf;
pwC7 = offC7.pw; rf7 = offC7.pwrf;
/* Example of semi-automatic calibration - use parameters, if they exist :
if ((autocal[0] == 's') || (autocal[1] == 's'))
{
if (find("pwC1") > 0) pwC1 = getval("pwC1");
if (find("rf1") > 0) rf1 = getval("rf1");
}
*/
}
/* power level and pulse times for DIPSI 1H decoupling */
DIPSI2time = 2.0*zeta + 2.0*timeTN - 5.4e-3 + pwC1 + 5.0*pwN + gt3 + 5.0e-5 + 2.0*GRADIENT_DELAY + 3.0*POWER_DELAY;
pwH=1.0/(4.0*waltzB1);
ncyc_dec = (DIPSI2time*90.0)/(pwH*2590.0*4.0);
ncyc_dec = (int) (ncyc_dec +0.5);
pwH = (DIPSI2time*90.0)/(ncyc_dec*2590.0*4.0); /* adjust pwH */
tpwr1 = 4095.0*(compH*pw/pwH);
tpwr1 = (int) (2.0*tpwr1 + 0.5); /* x2 because obs atten will be reduced by 6dB */
/* CHECK VALIDITY OF PARAMETER RANGES */
if ( 0.5*ni*1/(sw1) > timeAB - gt4 - WFG_START_DELAY - pwC7 )
{ printf(" ni is too big. Make ni equal to %d or less.\n",
((int)((timeAB - gt4 - WFG_START_DELAY - pwC7)*2.0*sw1))); psg_abort(1);}
PRexp = 0;
if((pra > 0.0) && (pra < 90.0)) PRexp = 1;
if (PRexp)
{
if( 0.5*ni*sna/sw1 > timeTN - WFG3_START_DELAY)
{ printf(" ni is too big. Make ni equal to %d or less.\n",
((int)((timeTN - WFG3_START_DELAY)*2.0*sw1/sna))); psg_abort(1);}
}
else
{
if ( 0.5*ni2*1/(sw2) > timeTN - WFG3_START_DELAY)
{ printf(" ni2 is too big. Make ni2 equal to %d or less.\n",
((int)((timeTN - WFG3_START_DELAY)*2.0*sw2))); psg_abort(1);}
}
if ( dm[A] == 'y' || dm[B] == 'y' || dm[C] == 'y' )
{ printf("incorrect dec1 decoupler flags! Should be 'nnn' "); psg_abort(1);}
if ( dm2[A] == 'y' || dm2[B] == 'y' )
{ printf("incorrect dec2 decoupler flags! Should be 'nny' "); psg_abort(1);}
if ( dm3[A] == 'y' || dm3[C] == 'y' )
{ printf("incorrect dec3 decoupler flags! Should be 'nyn' or 'nnn' ");
psg_abort(1);}
if ( dpwr2 > 50 )
{ printf("dpwr2 too large! recheck value "); psg_abort(1);}
if ( pw > 20.0e-6 )
{ printf(" pw too long ! recheck value "); psg_abort(1);}
if ( pwN > 100.0e-6 )
{ printf(" pwN too long! recheck value "); psg_abort(1);}
if ( TROSY[A]=='y' && dm2[C] == 'y')
{ text_error("Choose either TROSY='n' or dm2='n' ! "); psg_abort(1);}
/* PHASES AND INCREMENTED TIMES */
/* Phase incrementation for hypercomplex 2D data, States-Haberkorn element */
if (phase1 == 2) tsadd(t3,1,4);
if (TROSY[A]=='y')
{ if (phase2 == 2) icosel = +1;
else {tsadd(t4,2,4); tsadd(t10,2,4); icosel = -1;}
}
else { if (phase2 == 2) {tsadd(t10,2,4); icosel = +1;}
else icosel = -1;
}
/* Set up f1180 */
if(PRexp) /* set up Projection-Reconstruction experiment */
tau1 = d2*csa;
else
tau1 = d2;
if((f1180[A] == 'y') && (ni > 1.0))
{ tau1 += ( 1.0 / (2.0*sw1) ); if(tau1 < 0.2e-6) tau1 = 0.0; }
tau1 = tau1/2.0;
/* Set up f2180 */
if(PRexp)
tau2 = d2*sna;
else
{
tau2 = d3;
if((f2180[A] == 'y') && (ni2 > 1.0))
{ tau2 += ( 1.0 / (2.0*sw2) ); if(tau2 < 0.2e-6) tau2 = 0.0; }
}
tau2 = tau2/2.0;
/* Calculate modifications to phases for States-TPPI acquisition */
if( ix == 1) d2_init = d2;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if(t1_counter % 2)
{ tsadd(t3,2,4); tsadd(t12,2,4); }
if( ix == 1) d3_init = d3;
t2_counter = (int) ( (d3-d3_init)*sw2 + 0.5 );
if(t2_counter % 2)
{ tsadd(t8,2,4); tsadd(t12,2,4); }
/* BEGIN ACTUAL PULSE SEQUENCE */
status(A);
delay(d1);
if ( dm3[B] == 'y' )
{ lk_hold(); lk_sampling_off();} /*freezes z0 correction, stops lock pulsing*/
rcvroff();
obspower(tpwr);
decpower(pwClvl);
dec2power(pwNlvl);
decpwrf(rf0);
obsoffset(tof);
txphase(zero);
delay(1.0e-5);
if (TROSY[A] == 'n')
dec2rgpulse(pwN, zero, 0.0, 0.0); /*destroy N15 and C13 magnetization*/
decrgpulse(pwC, zero, 0.0, 0.0);
zgradpulse(gzlvl0, 0.5e-3);
delay(1.0e-4);
if (TROSY[A] == 'n')
dec2rgpulse(pwN, one, 0.0, 0.0);
decrgpulse(pwC, zero, 0.0, 0.0);
zgradpulse(0.7*gzlvl0, 0.5e-3);
delay(5.0e-4);
rgpulse(pw,zero,0.0,0.0); /* 1H pulse excitation */
decphase(zero);
zgradpulse(gzlvl0, gt0);
delay(tauCH - gt0);
simpulse(2.0*pw, 2.0*pwC, zero, zero, 0.0, 0.0);
txphase(one);
decphase(t3);
zgradpulse(gzlvl0, gt0);
delay(tauCH - gt0);
rgpulse(pw, one, 0.0, 0.0);
zgradpulse(gzlvl3, gt3);
delay(2.0e-4);
if ( dm3[B] == 'y' ) /* begins optional 2H decoupling */
{
gt4=0.0; /* no gradients during 2H decoupling */
dec3rgpulse(1/dmf3,one,10.0e-6,2.0e-6);
dec3unblank();
dec3phase(zero);
delay(2.0e-6);
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
}
decrgpulse(pwC, t3, 0.0, 0.0);
/* point a */
txphase(zero);
decphase(zero);
decpwrf(rf7);
delay(tau1);
/* WFG3_START_DELAY */
sim3shaped_pulse("", "offC7", "", 0.0, pwC7, 2.0*pwN, zero, zero, zero,
0.0, 0.0);
zgradpulse(gzlvl4, gt4);
decpwrf(rf2);
if ( pwC7 > 2.0*pwN)
{delay(timeCH - pwC7 - gt4 - WFG3_START_DELAY - 2.0*pw);}
else
{delay(timeCH - 2.0*pwN - gt4 - WFG3_START_DELAY - 2.0*pw);}
rgpulse(2.0*pw,zero,0.0,0.0);
delay(timeAB - timeCH);
decrgpulse(pwC2, zero, 0.0, 0.0);
zgradpulse(gzlvl4, gt4);
decpwrf(rf7);
delay(timeAB - tau1 - gt4 - WFG_START_DELAY - pwC7 - 2.0e-6);
/* WFG_START_DELAY */
decshaped_pulse("offC7", pwC7, zero, 0.0, 0.0);
decpwrf(rf1); /* point b */
decrgpulse(pwC1, zero, 2.0e-6, 0.0);
obspwrf(tpwr1); obspower(tpwr-6); /* POWER_DELAY */
obsprgon("dipsi2", pwH, 5.0); /* PRG_START_DELAY */
xmtron();
/* point c */
dec2phase(zero);
decpwrf(rf2);
delay(zeta - POWER_DELAY - PRG_START_DELAY);
sim3pulse(0.0, pwC2, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
decpwrf(rf1);
dec2phase(t8);
delay(zeta);
/* point d */
decrgpulse(pwC1, zero, 0.0, 0.0);
if ( dm3[B] == 'y' ) /* turns off 2H decoupling */
{
setstatus(DEC3ch, FALSE, 'c', FALSE, dmf3);
dec3rgpulse(1/dmf3,three,2.0e-6,2.0e-6);
dec3blank();
lk_autotrig(); /* resumes lock pulsing */
}
/* xxxxxxxxxxxxxxxxxx OPTIONS FOR N15 EVOLUTION xxxxxxxxxxxxxxxxxxxxx */
zgradpulse(gzlvl3, gt3);
if (TROSY[A]=='y') { xmtroff(); obsprgoff(); }
delay(2.0e-4);
dec2rgpulse(pwN, t8, 0.0, 0.0);
/* point e */
decpwrf(rf2);
decphase(zero);
dec2phase(t9);
delay(timeTN - WFG3_START_DELAY - tau2);
/* WFG3_START_DELAY */
sim3pulse(0.0, pwC2, 2.0*pwN, zero, zero, t9, 0.0, 0.0);
dec2phase(t10);
decpwrf(rf7);
if (TROSY[A]=='y')
{
if (tau2 > gt1 + 2.0*GRADIENT_DELAY + 1.0e-4)
{
txphase(t4);
delay(timeTN - pwC7 - WFG_START_DELAY); /* WFG_START_DELAY */
decshaped_pulse("offC7", pwC7, zero, 0.0, 0.0);
delay(tau2 - gt1 - 2.0*GRADIENT_DELAY - 1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspwrf(4095.0); obspower(tpwr); /* POWER_DELAY */
delay(1.0e-4 - 2.0*POWER_DELAY);
}
else
{
txphase(t4);
delay(timeTN -pwC7 -WFG_START_DELAY -gt1 -2.0*GRADIENT_DELAY -1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspwrf(4095.0); obspower(tpwr); /* POWER_DELAY */
delay(1.0e-4 - 2.0*POWER_DELAY); /* WFG_START_DELAY */
decshaped_pulse("offC7", pwC7, zero, 0.0, 0.0);
delay(tau2);
}
}
else
{
if (tau2 > kappa)
{
delay(timeTN - pwC7 - WFG_START_DELAY); /* WFG_START_DELAY */
decshaped_pulse("offC7", pwC7, zero, 0.0, 0.0);
delay(tau2 - kappa - PRG_STOP_DELAY);
xmtroff();
obsprgoff(); /* PRG_STOP_DELAY */
txphase(t4);
delay(kappa - gt1 - 2.0*GRADIENT_DELAY - 1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspwrf(4095.0); obspower(tpwr); /* POWER_DELAY */
delay(1.0e-4 - 2.0*POWER_DELAY);
}
else if (tau2 > (kappa - pwC7 - WFG_START_DELAY))
{
delay(timeTN + tau2 - kappa - PRG_STOP_DELAY);
xmtroff();
obsprgoff(); /* PRG_STOP_DELAY */
txphase(t4); /* WFG_START_DELAY */
decshaped_pulse("offC7", pwC7, zero, 0.0, 0.0);
delay(kappa -pwC7 -WFG_START_DELAY -gt1 -2.0*GRADIENT_DELAY -1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspwrf(4095.0); obspower(tpwr); /* POWER_DELAY */
delay(1.0e-4 - 2.0*POWER_DELAY);
}
else if (tau2 > gt1 + 2.0*GRADIENT_DELAY + 1.0e-4)
{
delay(timeTN + tau2 - kappa - PRG_STOP_DELAY);
xmtroff();
obsprgoff(); /* PRG_STOP_DELAY */
txphase(t4);
delay(kappa - tau2 - pwC7 - WFG_START_DELAY); /* WFG_START_DELAY */
decshaped_pulse("offC7", pwC7, zero, 0.0, 0.0);
delay(tau2 - gt1 - 2.0*GRADIENT_DELAY - 1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspwrf(4095.0); obspower(tpwr); /* POWER_DELAY */
delay(1.0e-4 - 2.0*POWER_DELAY);
}
else
{
delay(timeTN + tau2 - kappa - PRG_STOP_DELAY);
xmtroff();
obsprgoff(); /* PRG_STOP_DELAY */
txphase(t4);
delay(kappa-tau2-pwC7-WFG_START_DELAY-gt1-2.0*GRADIENT_DELAY-1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspwrf(4095.0); obspower(tpwr); /* POWER_DELAY */
delay(1.0e-4 - 2.0*POWER_DELAY); /* WFG_START_DELAY */
decshaped_pulse("offC7", pwC7, zero, 0.0, 0.0);
delay(tau2);
}
} /* point f */
/* xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx */
if (TROSY[A]=='y') rgpulse(pw, t4, 0.0, 0.0);
else sim3pulse(pw, 0.0, pwN, t4, zero, t10, 0.0, 0.0);
txphase(zero);
dec2phase(zero);
zgradpulse(gzlvl5, gt5);
if (TROSY[A]=='y') delay(lambda - 0.65*(pw + pwN) - gt5);
else delay(lambda - 1.3*pwN - gt5);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl5, gt5);
txphase(one);
dec2phase(t11);
delay(lambda - 1.3*pwN - gt5);
sim3pulse(pw, 0.0, pwN, one, zero, t11, 0.0, 0.0);
txphase(zero);
dec2phase(zero);
zgradpulse(gzlvl6, gt5);
delay(lambda - 1.3*pwN - gt5);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
dec2phase(t10);
zgradpulse(gzlvl6, gt5);
if (TROSY[A]=='y') delay(lambda - 1.6*pwN - gt5);
else delay(lambda - 0.65*pwN - gt5);
if (TROSY[A]=='y') dec2rgpulse(pwN, t10, 0.0, 0.0);
else rgpulse(pw, zero, 0.0, 0.0);
delay((gt1/10.0) + 1.0e-4 +gstab - 0.5*pw + 2.0*GRADIENT_DELAY + POWER_DELAY);
rgpulse(2.0*pw, zero, 0.0, rof1);
dec2power(dpwr2); /* POWER_DELAY */
if (mag_flg[A] == 'y') magradpulse(icosel*gzcal*gzlvl2, gt1/10.0);
else zgradpulse(icosel*gzlvl2, gt1/10.0); /* 2.0*GRADIENT_DELAY */
delay(gstab);
rcvron();
statusdelay(C,1.0e-4 - rof1);
if (dm3[B]=='y') lk_sample();
setreceiver(t12);
}
pulsesequence()
{
/* DECLARE VARIABLES */
char satmode[MAXSTR],
fscuba[MAXSTR],
fc180[MAXSTR], /* Flag for checking sequence */
ddseq[MAXSTR], /* 2H decoupling seqfile */
fCTCa[MAXSTR], /* Flag for CT or non_CT on Ca dimension */
sel_flg[MAXSTR],
cbdecseq[MAXSTR];
int icosel,
ni = getval("ni"),
t1_counter; /* used for states tppi in t1 */
double tau1, /* t1 delay */
tau2, /* t2 delay */
tau3, /* t2 delay */
taua, /* ~ 1/4JNH = 2.25 ms */
taub, /* ~ 1/4JNH = 2.25 ms */
tauc, /* ~ 1/4JCaC' = 4 ms */
taud, /* ~ 1/4JCaC' = 4.5 ms if bigTCo can be set to be
less than 4.5ms and then taud can be smaller*/
zeta, /* time for C'-N to refocuss set to 0.5*24.0 ms */
bigTCa, /* Ca T period */
bigTCo, /* Co T period */
bigTN, /* nitrogen T period */
BigT1, /* delay to compensate for gradient gt5 */
sw1, /* sweep width in f1 */
sw2, /* sweep width in f2 */
sphase, /* small angle phase shift */
sphase1,
sphase2, /* used only for constant t2 period */
pwS4, /* selective CO 180 */
pwS3, /* selective Ca 180 */
pwS1, /* selecive Ca 90 */
pwS2, /* selective CO 90 */
cbpwr, /* power level for selective CB decoupling */
cbdmf, /* pulse width for selective CB decoupling */
cbres, /* decoupling resolution of CB decoupling */
gt1,
gt2,
gt3,
gt4,
gt5,
gt6,
gt7,
gt8,
gt9,
gt10,
gt11,
gt12,
gstab,
gzlvl1,
gzlvl2,
gzlvl3,
gzlvl4,
gzlvl5,
gzlvl6,
gzlvl7,
gzlvl8,
gzlvl9,
gzlvl10,
gzlvl11,
gzlvl12,
compH = getval("compH"), /* adjustment for amplifier compression */
pwHs = getval ("pwHs"), /* H1 90 degree pulse at tpwrs */
tpwrs, /* power for pwHs ("H2osinc") pulse */
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
pwNlvl = getval("pwNlvl"), /* power for N15 pulses */
pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */
swCa = getval("swCa"),
swCO = getval("swCO"),
swN = getval("swN"),
swTilt, /* This is the sweep width of the tilt vector */
cos_N, cos_CO, cos_Ca,
angle_N, angle_CO, angle_Ca;
angle_N=0.0; /*initialize variable*/
/* LOAD VARIABLES */
getstr("satmode",satmode);
getstr("fc180",fc180);
getstr("fscuba",fscuba);
getstr("ddseq",ddseq);
getstr("fCTCa",fCTCa);
getstr("sel_flg",sel_flg);
taua = getval("taua");
taub = getval("taub");
tauc = getval("tauc");
taud = getval("taud");
zeta = getval("zeta");
bigTCa = getval("bigTCa");
bigTCo = getval("bigTCo");
bigTN = getval("bigTN");
BigT1 = getval("BigT1");
tpwr = getval("tpwr");
dpwr = getval("dpwr");
dpwr3 = getval("dpwr3");
sw1 = getval("sw1");
sw2 = getval("sw2");
sphase = getval("sphase");
sphase1 = getval("sphase1");
sphase2 = getval("sphase2");
gt1 = getval("gt1");
gt2 = getval("gt2");
gt3 = getval("gt3");
gt4 = getval("gt4");
gt5 = getval("gt5");
gt6 = getval("gt6");
gt7 = getval("gt7");
gt8 = getval("gt8");
gt9 = getval("gt9");
gt10 = getval("gt10");
gt11 = getval("gt11");
gt12 = getval("gt12");
gstab = getval("gstab");
gzlvl1 = getval("gzlvl1");
gzlvl2 = getval("gzlvl2");
gzlvl3 = getval("gzlvl3");
gzlvl4 = getval("gzlvl4");
gzlvl5 = getval("gzlvl5");
gzlvl6 = getval("gzlvl6");
gzlvl7 = getval("gzlvl7");
gzlvl8 = getval("gzlvl8");
gzlvl9 = getval("gzlvl9");
gzlvl10 = getval("gzlvl10");
gzlvl11 = getval("gzlvl11");
gzlvl12 = getval("gzlvl12");
/* Load variable */
cbpwr = getval("cbpwr");
cbdmf = getval("cbdmf");
cbres = getval("cbres");
tau1 = 0;
tau2 = 0;
tau3 = 0;
cos_N = 0;
cos_CO = 0;
cos_Ca = 0;
getstr("cbdecseq", cbdecseq);
/* LOAD PHASE TABLE */
settable(t1,1,phi1);
settable(t2,1,phi2);
settable(t3,4,phi3);
settable(t4,1,phi4);
settable(t5,1,phi5);
settable(t7,4,phi7);
settable(t8,4,phi8);
settable(t6,4,rec);
pwS1=c13pulsepw("ca", "co", "square", 90.0);
pwS2=c13pulsepw("co", "ca", "sinc", 90.0);
pwS3=c13pulsepw("ca", "co", "square", 180.0);
pwS4=c13pulsepw("co", "ca", "sinc", 180.0);
tpwrs = tpwr - 20.0*log10(pwHs/(compH*pw*1.69)); /*needs 1.69 times more*/
tpwrs = (int) (tpwrs); /*power than a square pulse */
/* CHECK VALIDITY OF PARAMETER RANGES */
if((dm[A] == 'y' || dm[B] == 'y' || dm[C] == 'y' ))
{
printf("incorrect dec1 decoupler flags! ");
psg_abort(1);
}
if((dm2[A] == 'y' || dm2[B] == 'y' || dm2[C] == 'y'))
{
printf("incorrect dec2 decoupler flags! Should be 'nnn' ");
psg_abort(1);
}
if( satpwr > 6 )
{
printf("TSATPWR too large !!! ");
psg_abort(1);
}
if( dpwr > 46 )
{
printf("don't fry the probe, DPWR too large! ");
psg_abort(1);
}
if( dpwr2 > 46 )
{
printf("don't fry the probe, DPWR2 too large! ");
psg_abort(1);
}
if( pwClvl > 62 )
{
printf("don't fry the probe, pwClvl too large! ");
psg_abort(1);
}
if( pw > 200.0e-6 )
{
printf("dont fry the probe, pw too high ! ");
psg_abort(1);
}
if( pwN > 200.0e-6 )
{
printf("dont fry the probe, pwN too high ! ");
psg_abort(1);
}
if( pwC > 200.0e-6 )
{
printf("dont fry the probe, pwC too high ! ");
psg_abort(1);
}
if( gt3 > 2.5e-3 )
{
printf("gt3 is too long\n");
psg_abort(1);
}
if( gt1 > 10.0e-3 || gt2 > 10.0e-3 || gt4 > 10.0e-3 || gt5 > 10.0e-3
|| gt6 > 10.0e-3 || gt7 > 10.0e-3 || gt8 > 10.0e-3
|| gt9 > 10.0e-3 || gt10 > 10.0e-3 || gt11 > 50.0e-6)
{
printf("gt values are too long. Must be < 10.0e-3 or gt11=50us\n");
psg_abort(1);
}
/* PHASES AND INCREMENTED TIMES */
/* Set up angles and phases */
angle_CO=getval("angle_CO"); cos_CO=cos(PI*angle_CO/180.0);
angle_Ca=getval("angle_Ca"); cos_Ca=cos(PI*angle_Ca/180.0);
if ( (angle_CO < 0) || (angle_CO > 90) )
{ printf ("angle_CO must be between 0 and 90 degree.\n"); psg_abort(1); }
if ( (angle_Ca < 0) || (angle_Ca > 90) )
{ printf ("angle_Ca must be between 0 and 90 degree.\n"); psg_abort(1); }
if ( 1.0 < (cos_CO*cos_CO + cos_Ca*cos_Ca) )
{
printf ("Impossible angles.\n"); psg_abort(1);
}
else
{
cos_N=sqrt(1.0- (cos_CO*cos_CO + cos_Ca*cos_Ca));
angle_N = 180.0*acos(cos_N)/PI;
}
swTilt=swCO*cos_CO + swCa*cos_Ca + swN*cos_N;
if (ix ==1)
{
printf("\n\nn\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n");
printf ("Maximum Sweep Width: \t\t %f Hz\n", swTilt);
printf ("Anlge_CO:\t%6.2f\n", angle_CO);
printf ("Anlge_Ca:\t%6.2f\n", angle_Ca);
printf ("Anlge_N :\t%6.2f\n", angle_N );
}
/* Set up hyper complex */
/* sw1 is used as symbolic index */
if ( sw1 < 1000 ) { printf ("Please set sw1 to some value larger than 1000.\n"); psg_abort(1); }
if (ix == 1) d2_init = d2;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if (t1_counter % 2) { tsadd(t2,2,4); tsadd(t6,2,4); }
if (phase1 == 1) { ;} /* CC */
else if (phase1 == 2) { tsadd(t5,1,4);} /* SC */
else if (phase1 == 3) { tsadd(t1,1,4); } /* CS */
else if (phase1 == 4) { tsadd(t5,1,4); tsadd(t1,1,4); } /* SS */
else { printf ("phase1 can only be 1,2,3,4. \n"); psg_abort(1); }
if (phase2 == 2) { tsadd(t4,2,4); icosel = 1; } /* N */
else icosel = -1;
tau1 = 1.0*t1_counter*cos_Ca/swTilt;
tau2 = 1.0*t1_counter*cos_CO/swTilt;
tau3 = 1.0*t1_counter*cos_N/swTilt;
tau1 = tau1/2.0; tau2 = tau2/2.0; tau3 = tau3/2.0;
/* CHECK VALIDITY OF PARAMETER RANGES */
if (bigTN - 0.5*ni*(cos_N/swTilt) + pwS4 < 0.2e-6)
{ printf(" ni is too big. Make ni equal to %d or less.\n",
((int)((bigTN + pwS4)*2.0*swTilt/cos_N))); psg_abort(1);}
if ((fCTCa[A]=='y') && (bigTCa - 0.5*ni*(cos_Ca/swTilt) - WFG_STOP_DELAY
- POWER_DELAY - gt11 - 50.2e-6 < 0.2e-6))
{
printf(" ni is too big for Ca. Make ni equal to %d or less.\n",
(int) ((bigTCa -WFG_STOP_DELAY
- POWER_DELAY - gt11 - 50.2e-6)/(0.5*cos_Ca/swTilt)) );
psg_abort(1);
}
if (bigTCo - 0.5*ni*(cos_CO/swTilt) - 4.0e-6 - POWER_DELAY < 0.2e-6)
{
printf(" ni is too big for CO. Make ni equal to %d or less.\n",
(int) ((bigTCo - 4.0e-6 - POWER_DELAY) / (0.5*cos_CO/swTilt)) );
psg_abort(1);
}
/* BEGIN ACTUAL PULSE SEQUENCE */
status(A);
obsoffset(tof);
obspower(satpwr); /* Set transmitter power for 1H presaturation */
obspwrf(4095.0);
decpower(pwClvl); /* Set Dec1 power for hard 13C pulses */
decpwrf(4095.0);
dec2power(pwNlvl); /* Set Dec2 power for 15N hard pulses */
dec2pwrf(4095.0);
set_c13offset("ca"); /* set Dec1 carrier at Ca */
sim3_c13pulse("", "ca", "co", "square", "", 0.0, 180.0, 0.0,
zero, zero, zero, 2.0e-6, 0.0);
set_c13offset("co"); /* set Dec1 carrier at Co */
/* Presaturation Period */
if (satmode[0] == 'y')
{
delay(2.0e-5);
rgpulse(d1,zero,2.0e-6,2.0e-6); /* presaturation */
obspower(tpwr); /* Set transmitter power for hard 1H pulses */
delay(2.0e-5);
if(fscuba[0] == 'y')
{
delay(2.2e-2);
rgpulse(pw,zero,2.0e-6,0.0);
rgpulse(2*pw,one,2.0e-6,0.0);
rgpulse(pw,zero,2.0e-6,0.0);
delay(2.2e-2);
}
}
else
{
delay(d1);
}
obspower(tpwr); /* Set transmitter power for hard 1H pulses */
txphase(one);
dec2phase(zero);
delay(1.0e-5);
/* Begin Pulses */
status(B);
rcvroff();
lk_hold();
shiftedpulse("sinc", pwHs, 90.0, 0.0, one, 2.0e-6, 0.0);
txphase(zero);
delay(2.0e-6);
/* xxxxxxxxxxxxxxxxxxxxxx 1HN to 15N TRANSFER xxxxxxxxxxxxxxxxxx */
rgpulse(pw,zero,0.0,0.0); /* 90 deg 1H pulse */
delay(0.2e-6);
zgradpulse(gzlvl1, gt1);
delay(2.0e-6);
delay(taua - gt1 - 2.2e-6); /* taua <= 1/4JNH */
sim3pulse(2*pw,0.0,2*pwN,zero,zero,zero,0.0,0.0);
txphase(three); dec2phase(zero); decphase(zero);
delay(taua - gt1 - gstab -0.2e-6 - 2.0e-6);
delay(0.2e-6);
zgradpulse(gzlvl1, gt1);
delay(gstab);
/* xxxxxxxxxxxxxxxxxxxxxx 15N to 13CO TRANSFER xxxxxxxxxxxxxxxxxx */
if(sel_flg[A] == 'n') {
rgpulse(pw,three,2.0e-6,0.0);
delay(0.2e-6);
zgradpulse(gzlvl2, gt2);
delay(gstab);
dec2rgpulse(pwN,zero,0.0,0.0);
delay( zeta + pwS4 );
dec2rgpulse(2*pwN,zero,0.0,0.0);
c13pulse("co", "ca", "sinc", 180.0, zero, 0.0, 0.0);
dec2phase(one);
delay(zeta - 2.0e-6);
dec2rgpulse(pwN,one,2.0e-6,0.0);
}
else {
rgpulse(pw,one,2.0e-6,0.0);
initval(1.0,v6);
dec2stepsize(45.0);
dcplr2phase(v6);
delay(0.2e-6);
zgradpulse(gzlvl2, gt2);
delay(gstab);
dec2rgpulse(pwN,zero,0.0,0.0);
dcplr2phase(zero); dec2phase(zero);
delay(1.34e-3 - SAPS_DELAY - 2.0*pw);
rgpulse(pw,one,0.0,0.0);
rgpulse(2.0*pw,zero,0.0,0.0);
rgpulse(pw,one,0.0,0.0);
delay( zeta - 1.34e-3 - 2.0*pw + pwS4 );
dec2rgpulse(2*pwN,zero,0.0,0.0);
c13pulse("co", "ca", "sinc", 180.0, zero, 0.0, 0.0);
dec2phase(one);
delay(zeta - 2.0e-6);
dec2rgpulse(pwN,one,2.0e-6,0.0);
}
dec2phase(zero); decphase(zero);
delay(0.2e-6);
zgradpulse(gzlvl3, gt3);
delay(gstab);
/* xxxxxxxxxxxxxxxxxxxxx 13CO to 13CA TRANSFER xxxxxxxxxxxxxxxxxxxxxxx */
c13pulse("co", "ca", "sinc", 90.0, zero, 2.0e-6, 0.0);
delay(2.0e-7);
zgradpulse(gzlvl10, gt10);
delay(100.0e-6);
delay(tauc - POWER_DELAY - gt10 - 100.2e-6 - (0.5*10.933*pwC));
decrgpulse(pwC*158.0/90.0, zero, 0.0, 0.0);
decrgpulse(pwC*171.2/90.0, two, 0.0, 0.0);
decrgpulse(pwC*342.8/90.0, zero, 0.0, 0.0); /* Shaka 6 composite */
decrgpulse(pwC*145.5/90.0, two, 0.0, 0.0);
decrgpulse(pwC*81.2/90.0, zero, 0.0, 0.0);
decrgpulse(pwC*85.3/90.0, two, 0.0, 0.0);
delay(2.0e-7);
zgradpulse(gzlvl10, gt10);
delay(100.0e-6);
delay(tauc - POWER_DELAY - 4.0e-6 - gt10 - 100.2e-6 - (0.5*10.933*pwC));
c13pulse("co", "ca", "sinc", 90.0, one, 4.0e-6, 0.0);
set_c13offset("ca"); /* change Dec1 carrier to Ca (55 ppm) */
delay(0.2e-6);
zgradpulse(gzlvl9, gt9);
delay(gstab);
/* xxxxxxxxxxxxxxxxxx 13CA EVOLUTION xxxxxxxxxxxxxxxxxxxxxx */
/* Turn on D decoupling using the third decoupler */
dec3unblank(); dec3rgpulse(1/dmf3, one, 0.0, 0.0);
dec3unblank(); setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
/* Turn on D decoupling */
c13pulse("ca", "co", "square", 90.0, t5, 2.0e-6, 0.0);
if (fCTCa[A]=='y')
{
/* Constant t2 */
decpower(cbpwr);
decphase(zero);
decprgon(cbdecseq,1/cbdmf,cbres);
decon();
delay(tau1);
decoff();
decprgoff();
decpower(pwClvl);
dec2rgpulse(pwN,one,0.0,0.0);
dec2rgpulse(2*pwN,zero,0.0,0.0);
dec2rgpulse(pwN,one,0.0,0.0);
c13pulse("co", "ca", "sinc", 180.0, zero, 0.0, 0.0);
decpower(cbpwr);
decphase(zero);
decprgon(cbdecseq,1/cbdmf,cbres);
decon();
delay(bigTCa - 4.0*pwN - WFG_START_DELAY - pwS4
- WFG_STOP_DELAY - POWER_DELAY - WFG_START_DELAY - gt11 - gstab -0.2e-6);
decoff();
decprgoff();
decpower(pwClvl);
delay(0.2e-6);
zgradpulse(gzlvl11, gt11);
delay(gstab);
initval(1.0,v3);
decstepsize(140);
dcplrphase(v3);
c13pulse("ca", "co", "square", 180.0, zero, 0.0, 0.0);
delay(0.2e-6);
zgradpulse(gzlvl11, gt11);
delay(gstab);
decpower(cbpwr);
decphase(zero);
decprgon(cbdecseq,1/cbdmf,cbres);
decon();
delay(bigTCa - tau1 - WFG_STOP_DELAY - POWER_DELAY - gt11 - gstab -0.2e-6);
decoff();
decprgoff();
}
/* non_constant t2 */
else
{
if (fc180[A]=='n')
{
if ((ni>1.0) && (tau1>0.0))
{
if (tau1 - 2.0*pwS1/PI - PRG_START_DELAY - 2*POWER_DELAY -
PRG_STOP_DELAY - pwN > 0.0)
{
decpower(cbpwr);
decphase(zero);
decprgon(cbdecseq,1/cbdmf,cbres);
decon();
delay(tau1 - 2.0*pwS1/PI - PRG_START_DELAY - 2*POWER_DELAY -
PRG_STOP_DELAY - pwN);
decoff();
decprgoff();
decphase(zero); dec2phase(zero);
decpower(pwClvl);
sim3_c13pulse("", "co", "ca", "sinc", "", 0.0, 180.0, 2.0*pwN,
zero, zero, zero, 0.0, 0.0);
decpower(cbpwr);
decphase(zero);
decprgon(cbdecseq,1/cbdmf,cbres);
decon();
delay(tau1 - 2.0*pwS1/PI - PRG_START_DELAY - 2*POWER_DELAY -
PRG_STOP_DELAY - pwN);
decoff();
decprgoff();
decstepsize(1.0);
initval(sphase1, v3);
dcplrphase(v3);
}
else
{
tsadd(t6,2,4);
delay(2.0*tau1);
delay(10.0e-6);
sim3_c13pulse("", "ca", "co", "square", "", 0.0, 180.0, 2.0*pwN,
zero, zero, zero, 2.0e-6, 0.0);
delay(10.0e-6);
}
}
else
{
tsadd(t6,2,4);
delay(10.0e-6);
sim3_c13pulse("", "ca", "co", "square", "", 0.0, 180.0, 2.0*pwN,
zero, zero, zero, 2.0e-6, 0.0);
delay(10.0e-6);
}
}
else
{
/* for checking sequence */
c13pulse("ca", "co", "square", 180.0, zero, 2.0e-6, 0.0);
}
}
decpower(pwClvl);
decphase(t7);
c13pulse("ca", "co", "square", 90.0, t7, 4.0e-6, 0.0);
dcplrphase(zero);
/* Turn off D decoupling */
dec3rgpulse(1/dmf3, three, 0.0, 0.0); dec3blank();
setstatus(DEC3ch, FALSE, 'w', FALSE, dmf3); dec3blank();
/* Turn off D decoupling */
set_c13offset("co"); /* set carrier back to Co */
delay(0.2e-6);
zgradpulse(gzlvl12, gt12);
delay(gstab);
/* xxxxxxxxxxxxxxx 13CA to 13CO TRANSFER and CT 13CO EVOLUTION xxxxxxxxxxxxxxxxx */
c13pulse("co", "ca", "sinc", 90.0, t1, 2.0e-6, 0.0);
delay(tau2);
dec2rgpulse(pwN,one,0.0,0.0);
dec2rgpulse(2*pwN,zero,0.0,0.0);
dec2rgpulse(pwN,one,0.0,0.0);
delay(taud - 4.0*pwN - POWER_DELAY
- 0.5*(WFG_START_DELAY + pwS3 + WFG_STOP_DELAY));
c13pulse("ca", "co", "square", 180.0, zero, 0.0, 0.0);
decphase(t8);
initval(1.0,v4);
decstepsize(sphase);
dcplrphase(v4);
delay(bigTCo - taud
- 0.5*(WFG_START_DELAY + pwS3 + WFG_STOP_DELAY) );
c13pulse("co", "ca", "sinc", 180.0, t8, 0.0, 0.0);
dcplrphase(zero); decphase(one);
delay(bigTCo - tau2 - POWER_DELAY - 4.0e-6);
c13pulse("co", "ca", "sinc", 90.0, one, 4.0e-6, 0.0);
delay(0.2e-6);
zgradpulse(gzlvl4, gt4);
delay(gstab);
/* t3 period */
dec2rgpulse(pwN,t2,2.0e-6,0.0);
dec2phase(t3);
delay(bigTN - tau3 + pwS4);
dec2rgpulse(2*pwN,t3,0.0,0.0);
c13pulse("co", "ca", "sinc", 180.0, zero, 0.0, 0.0);
txphase(zero);
dec2phase(t4);
delay(bigTN - gt5 - gstab -0.2e-6 - 2.0*GRADIENT_DELAY
- 4.0e-6 - WFG_START_DELAY - pwS3 - WFG_STOP_DELAY);
delay(0.2e-6);
zgradpulse(icosel*gzlvl5, gt5);
delay(gstab);
c13pulse("ca", "co", "square", 180.0, zero, 4.0e-6, 0.0);
delay(tau3);
sim3pulse(pw,0.0,pwN,zero,zero,t4,0.0,0.0);
delay(0.2e-6);
zgradpulse(gzlvl6, gt6);
delay(2.0e-6);
dec2phase(zero);
delay(taub - gt6 - 2.2e-6);
sim3pulse(2*pw,0.0,2*pwN,zero,zero,zero,0.0,0.0);
delay(0.2e-6);
zgradpulse(gzlvl6, gt6);
delay(200.0e-6);
txphase(one);
dec2phase(one);
delay(taub - gt6 - 200.2e-6);
sim3pulse(pw,0.0,pwN,one,zero,one,0.0,0.0);
delay(0.2e-6);
zgradpulse(gzlvl7, gt7);
delay(2.0e-6);
txphase(zero);
dec2phase(zero);
delay(taub - gt7 - 2.2e-6);
sim3pulse(2*pw,0.0,2*pwN,zero,zero,zero,0.0,0.0);
delay(0.2e-6);
zgradpulse(gzlvl7, gt7);
delay(200.0e-6);
delay(taub - gt7 - 200.2e-6);
sim3pulse(pw,0.0,pwN,zero,zero,zero,0.0,0.0);
delay(0.2e-6);
zgradpulse(-gzlvl8, gt8/2.0);
delay(50.0e-6);
delay(BigT1 - gt8/2.0 - 50.2e-6 - 0.5*(pwN - pw) - 2.0*pw/PI);
rgpulse(2*pw,zero,0.0,0.0);
delay(0.2e-6);
zgradpulse(gzlvl8, gt8/2.0);
delay(50.0e-6);
dec2power(dpwr2);
decpower(dpwr);
delay(BigT1 - gt8/2.0 - 50.2e-6 - 2.0*POWER_DELAY);
lk_sample();
/* rcvron(); */ /* Turn on receiver to warm up before acq */
/* BEGIN ACQUISITION */
status(C);
setreceiver(t6);
}
pulsesequence()
{
/* DECLARE AND LOAD VARIABLES */
char f1180[MAXSTR], /* Flag to start t1 @ halfdwell */
f2180[MAXSTR], /* Flag to start t2 @ halfdwell */
RELAY[MAXSTR], /* Insert HCCH-relay delay */
ribose[MAXSTR], /* ribose CHn groups only */
aromatic[MAXSTR], /* aromatic CHn groups only */
rna_stCshape[MAXSTR], /* calls sech/tanh pulses from shapelib */
rna_stCdec[MAXSTR], /* calls STUD+ waveforms from shapelib */
mag_flg[MAXSTR], /* Flag to use magic-angle gradients */
H2O_flg[MAXSTR],
sspul[MAXSTR],
SHAPE[MAXSTR],
STUD[MAXSTR]; /* apply automatically calculated STUD decoupling */
int t1_counter, /* used for states tppi in t1 */
t2_counter, /* used for states tppi in t2 */
ni2 = getval("ni2");
double tau1, /* t1 delay */
tau2, /* t2 delay */
delta1,delta2,
ni = getval("ni"),
lambda = 0.94/(4*getval("JCH")), /* 1/4J H1 evolution delay */
tCH = 1/(6.0*getval("JCH")), /* 1/4J C13 evolution delay */
tCC = 1/(8*getval("JCC")),
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
rfC, /* maximum fine power when using pwC pulses */
compC = getval("compC"), /* adjustment for C13 amplifier compression */
/* temporary Pbox parameters */
bw, pws, ofs, ppm, nst, /* bandwidth, pulsewidth, offset, ppm, # steps */
/* Sech/tanh inversion pulses automatically calculated by macro "rna_cal" */
/* and string parameter rna_stCshape calls them from your shapelib. */
rfst = 0.0, /* fine power for the rna_stCshape pulse, initialised */
dofa, /* dof shifted to 80 or 120ppm for ribose or aromatic spectra */
/* string parameter stCdec calls stud decoupling waveform from your shapelib.*/
studlvl, /* coarse power for STUD+ decoupling */
stdmf = getval("dmf80"), /* dmf for 80 ppm of STUD decoupling */
rf80 = getval("rf80"), /* rf in Hz for 80ppm STUD+ */
pwNlvl = getval("pwNlvl"), /* power for N15 pulses */
pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */
sw1 = getval("sw1"),
sw2 = getval("sw2"),
gt3 = getval("gt3"),
gt4 = getval("gt4"),
gt5 = getval("gt5"),
gt7 = getval("gt7"),
gt8 = getval("gt8"),
gt9 = getval("gt9"),
gzcal = getval("gzcal"),
grecov = getval("grecov"),
gzlvl0 = getval("gzlvl0"),
gzlvl3 = getval("gzlvl3"),
gzlvl4 = getval("gzlvl4"),
gzlvl5 = getval("gzlvl5"),
gzlvl7 = getval("gzlvl7"), /* triax option */
gzlvl8 = getval("gzlvl8"),
gzlvl9 = getval("gzlvl9");
getstr("f1180",f1180);
getstr("mag_flg",mag_flg);
getstr("f2180",f2180);
getstr("RELAY",RELAY);
getstr("ribose",ribose);
getstr("aromatic",aromatic);
getstr("H2O_flg",H2O_flg);
getstr("sspul",sspul);
getstr("SHAPE",SHAPE);
getstr("STUD",STUD);
/* INITIALIZE VARIABLES */
/* maximum fine power for pwC pulses */
rfC = 4095.0;
setautocal(); /* activate auto-calibration flags */
if (autocal[0] == 'n')
{
/* 50ppm sech/tanh inversion */
rfst = (compC*4095.0*pwC*4000.0*sqrt((7.5*sfrq/600+3.85)/0.41));
rfst = (int) (rfst + 0.5);
}
else /* if autocal = 'y'(yes), 'q'(quiet), r(read), or 's'(semi) */
{
if(FIRST_FID) /* call Pbox */
{
ppm = getval("dfrq");
bw = 50.0*ppm; pws = 0.001; ofs = 0.0; nst = 500.0;
stC50 = pbox_makeA("rna_stC50", "sech", bw, pws, ofs, compC*pwC, pwClvl, nst);
if (dm3[B] == 'y') H2ofs = 3.2;
ofs_check(H1ofs, C13ofs, N15ofs, H2ofs);
}
rfst = stC50.pwrf;
}
strcpy(rna_stCshape, "rna_stC50");
strcpy(rna_stCdec, "wurst80");
studlvl = pwClvl + 20.0*log10(compC*pwC*4.0*rf80);
studlvl = (int) (studlvl + 0.5);
/* RIBOSE spectrum only, centered on 80ppm. */
if (ribose[A]=='y')
dofa = dof - 30.0*dfrq;
/* AROMATIC spectrum only, centered on 120ppm */
else
dofa = dof + 10*dfrq;
/* CHECK VALIDITY OF PARAMETER RANGES */
if( dpwrf < 4095 )
{ printf("reset dpwrf=4095 and recalibrate C13 90 degree pulse");
psg_abort(1); }
if( pwC > (24.0e-6*600.0/sfrq) )
{ printf("Increase pwClvl so that pwC < 24*600/sfrq");
psg_abort(1); }
if((dm[A] == 'y' || dm[B] == 'y' ))
{ printf("incorrect Dec1 decoupler flags! "); psg_abort(1);}
if((dm2[A] == 'y' || dm2[B] == 'y'))
{ printf("incorrect Dec2 decoupler flags! "); psg_abort(1);}
if((dm3[A] == 'y' || dm3[C] == 'y' ))
{printf("incorrect dec1 decoupler flags! Should be 'nyn' or 'nnn' ");
psg_abort(1); }
if ((dm3[B] == 'y' && dpwr3 > 44 ))
{ printf("Deuterium decoupling power too high ! "); psg_abort(1);}
if( dpwr > 50 )
{ printf("don't fry the probe, dpwr too large! "); psg_abort(1);}
if( dpwr2 > 50 )
{ printf("don't fry the probe, dpwr2 too large! "); psg_abort(1); }
/* CHOICE OF PULSE SEQUENCE */
if ( ((ribose[A]=='y') && (aromatic[A]=='y')) )
{ text_error("Choose ONE of ribose='y' OR aromatic='y' ! ");
psg_abort(1); }
if ( ((aromatic[A]=='y') && (RELAY[A]=='y')) )
{ text_error("No RELAY with aromatic='y' ! ");
psg_abort(1); }
/* LOAD VARIABLES */
settable(t1, 2, phi1);
settable(t2, 4, phi2);
settable(t3, 16, phi3);
settable(t4, 2, phi4);
settable(t11,8, rec);
/* INITIALIZE VARIABLES */
/* Phase incrementation for hypercomplex data */
if ( phase1 == 2 ) /* Hypercomplex in t1 */
tsadd(t1,1,4);
if ( phase2 == 2 )
tsadd(t2,1,4);
/* calculate modification to phases based on current t1 values
to achieve States-TPPI acquisition */
if(ix == 1) d2_init = d2;
t1_counter = (int)((d2-d2_init)*sw1 + 0.5);
if(t1_counter % 2)
{
tsadd(t1,2,4);
tsadd(t11,2,4);
}
/* calculate modification to phases based on current t2 values
to achieve States-TPPI acquisition */
if(ix == 1) d3_init = d3;
t2_counter = (int)((d3-d3_init)*sw2 + 0.5);
if(t2_counter % 2)
{
tsadd(t2,2,4);
tsadd(t11,2,4);
}
/* set up so that get (90, -180) phase corrects in F1 if f1180 flag is y */
tau1 = d2;
if(f1180[A] == 'y')
{
tau1 += (1.0/(2.0*sw1));
}
if (tau1 < 1.0e-6) tau1 = 0.0;
tau1 = tau1/2.0;
/* set up so that get (90, -180) phase corrects in F2 if f2180 flag is y */
tau2 = d3;
if(f2180[A] == 'y')
{
tau2 += (1.0/(2.0*sw2));
}
if (tau2 < 1.0e-6) tau2 = 0.0;
tau2 = tau2/2.0;
if (ni > 1)
delta1 = (double)(t1_counter*(lambda - gt5 - 0.2e-3))/((double)(ni-1));
else delta1 = 0.0;
if (ni2 > 1)
delta2 = (double)(t2_counter*(tCC - 0.6e-3))/((double)(ni2-1));
else delta2 = 0.0;
initval(7.0, v1);
obsstepsize (45.0);
/* BEGIN ACTUAL PULSE SEQUENCE */
status(A);
obsoffset(tof);
decoffset(dofa);
dec2offset(dof2);
obspower(tpwr-12);
decpower(pwClvl);
decpwrf(rfC);
dec2power(pwNlvl);
decphase(zero);
dec2phase(zero);
if (sspul[0] == 'y')
{
rgpulse(200*pw, one, 10.0e-6, 0.0e-6);
rgpulse(200*pw, zero, 0.0e-6, 1.0e-6);
}
obspower(tpwr);
xmtrphase(v1);
txphase(t1);
if (dm3[B] == 'y') lk_sample();
delay(d1);
if (dm3[B] == 'y') lk_hold();
rcvroff();
decrgpulse(pwC, zero, rof1, rof1);
delay(rof1);
zgradpulse(gzlvl0,0.5e-3);
delay(grecov);
if(dm3[B] == 'y') /*optional 2H decoupling on */
{
dec3unblank();
dec3rgpulse(1/dmf3, one, 0.0, 0.0);
dec3unblank();
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
}
status(B);
rgpulse(pw, t1, 1.0e-4, rof1);
xmtrphase(zero);
txphase(zero);
zgradpulse(gzlvl5,gt5);
/*
decpwrf(rfst);
delay(lambda - gt5 - rof1 - SAPS_DELAY - GRADIENT_DELAY - POWER_DELAY -
WFG2_START_DELAY - 0.5e-3 + 70.0e-6 + tau1);
decshaped_pulse(rna_stCshape, 1.0e-3, zero, 0.0, 0.0);
delay(tau1 - delta1);
rgpulse(2.0*pw, zero, 0.0, rof1);
txphase(one);
decpwrf(rfC);
zgradpulse(gzlvl5,gt5);
delay(lambda - delta1 - gt5 - rof1 - GRADIENT_DELAY - POWER_DELAY - 0.5e-3 + 70.0e-6);
*/
delay(lambda - gt5 - rof1 - SAPS_DELAY - GRADIENT_DELAY + tau1);
decrgpulse(2*pwC, zero, 0.0, 0.0);
delay(tau1 - delta1);
rgpulse(2.0*pw, zero, 0.0, rof1);
txphase(one);
zgradpulse(gzlvl5,gt5);
delay(lambda - delta1 - gt5 - rof1 - GRADIENT_DELAY);
rgpulse(pw, one, 0.0, rof1);
decphase(t2);
txphase(zero);
if(mag_flg[A] == 'y')
magradpulse(gzcal*gzlvl3,gt3);
else
zgradpulse(gzlvl3,gt3);
delay(grecov);
decrgpulse(pwC, t2, rof1, 0.0);
decphase(zero);
delay(tau2);
dec2rgpulse(2.0*pwN,zero,0.0,0.0);
delay(tCH - 2*pwN);
rgpulse(2.0*pw, zero, 0.0, 0.0);
decphase(t3);
delay(tCC - tCH + tau2 - delta2 - 2.0*pw);
decrgpulse(2.0*pwC, t3, 0.0, 0.0);
decphase(t4);
delay(tCC - delta2);
decrgpulse(pwC, t4, 0.0, rof1);
txphase(zero);
decphase(zero);
if(RELAY[A] == 'y')
{
zgradpulse(gzlvl4, gt4);
delay(tCC - gt4 - GRADIENT_DELAY - pwC);
decrgpulse(2.0*pwC, zero, 0.0, 0.0);
zgradpulse(gzlvl4, gt4);
delay(tCC - gt4 - GRADIENT_DELAY - pwC);
decrgpulse(pwC, zero, 0.0, 0.0);
}
zgradpulse(gzlvl4,gt4);
delay(tCC - gt4);
decrgpulse(2.0*pwC, zero, 0.0, rof1);
if (H2O_flg[A] == 'y')
{
delay(tCC - gt4 - grecov - POWER_DELAY);
zgradpulse(gzlvl4,gt4);
txphase(one);
decphase(one);
delay(grecov);
decrgpulse(pwC, one, 0.0, rof1);
rgpulse(900*pw, one, 0.0, rof1);
txphase(zero);
rgpulse(500*pw, zero, rof1, rof1);
decphase(one);
if(mag_flg[A] == 'y')
magradpulse(gzcal*gzlvl7,gt7);
else
zgradpulse(gzlvl7,gt7);
delay(200.0e-6);
simpulse(pw, pwC, zero, one, 0.0, rof1);
decphase(zero);
zgradpulse(gzlvl4,gt4);
delay(tCH - gt4);
simpulse(2.0*pw, 2.0*pwC, zero, zero, 0.0, rof1);
zgradpulse(gzlvl4,gt4);
delay(tCH - gt4);
}
else
{
delay(tCC - tCH - 2.0*pw - POWER_DELAY);
rgpulse(2.0*pw, zero, 0.0, rof1);
zgradpulse(gzlvl4,gt4);
delay(tCH - gt4 - rof1);
}
decrgpulse(pwC, zero, 0.0, rof1);
txphase(zero);
if(mag_flg[A] == 'y')
magradpulse(gzcal*gzlvl8,gt8);
else
zgradpulse(gzlvl8,gt8);
delay(grecov);
if(dm3[B] == 'y') /*optional 2H decoupling off */
{
dec3rgpulse(1/dmf3, three, 0.0, 0.0);
dec3blank();
setstatus(DEC3ch, FALSE, 'w', FALSE, dmf3);
dec3blank();
}
rgpulse(pw, zero, 0.0, rof1);
if (SHAPE[A] =='y')
{
decpwrf(rfst);
if(mag_flg[A] == 'y')
magradpulse(gzcal*gzlvl9,gt9);
else
zgradpulse(gzlvl9,gt9);
delay(lambda - gt9 - GRADIENT_DELAY - POWER_DELAY - WFG2_START_DELAY - 0.5e-3 + 70.0e-6);
simshaped_pulse("",rna_stCshape,2*pw, 1.0e-3, zero, zero, 0.0, rof1);
decphase(zero);
if(mag_flg[A] == 'y')
magradpulse(gzcal*gzlvl9,gt9);
else
zgradpulse(gzlvl9,gt9);
decpwrf(rfC);
if (STUD[A]=='y') decpower(studlvl); else decpower(dpwr);
delay(lambda - gt9 -rof1 -0.5*pw - 2*POWER_DELAY - GRADIENT_DELAY - 0.5e-3 + 70.0e-6);
}
else
{
if(mag_flg[A] == 'y')
magradpulse(gzcal*gzlvl9,gt9);
else
zgradpulse(gzlvl9,gt9);
delay(lambda - gt9 - GRADIENT_DELAY);
simpulse(2*pw, 2*pwC, zero, zero, 0.0, rof1);
if(mag_flg[A] == 'y')
magradpulse(gzcal*gzlvl9,gt9);
else
zgradpulse(gzlvl9,gt9);
if (STUD[A]=='y') decpower(studlvl); else decpower(dpwr);
delay(lambda - gt9 -rof1 -0.5*pw - POWER_DELAY - GRADIENT_DELAY);
}
rgpulse(pw, zero, rof1, rof2);
rcvron();
if (dm3[B] == 'y') lk_sample();
setreceiver(t11);
if ((STUD[A]=='y') && (dm[C] == 'y'))
{
decunblank();
decon();
decprgon(rna_stCdec,1/stdmf, 1.0);
startacq(alfa);
acquire(np, 1.0/sw);
decprgoff();
decoff();
decblank();
}
else
status(C);
setreceiver(t11);
}
void pulsesequence()
{
/* DECLARE AND LOAD VARIABLES */
char f1180[MAXSTR], /* Flag to start t1 @ halfdwell */
mag_flg[MAXSTR], /*magic angle gradient*/
f2180[MAXSTR], /* Flag to start t2 @ halfdwell */
stCdec[MAXSTR], /* calls STUD+ waveforms from shapelib */
STUD[MAXSTR]; /* apply automatically calculated STUD decoupling */
int icosel1, /* used to get n and p type */
icosel2,
t1_counter, /* used for states tppi in t1 */
t2_counter, /* used for states tppi in t2 */
ni2 = getval("ni2");
double tau1, /* t1 delay */
tau2, /* t2 delay */
del = getval("del"), /* time delays for CH coupling evolution */
BPdpwrspinlock, /* user-defined upper limit for spinlock(Hz) */
BPpwrlimits, /* =0 for no limit, =1 for limit */
del1 = getval("del1"),
del2 = getval("del2"),
/* STUD+ waveforms automatically calculated by macro "biocal" */
/* and string parameter stCdec calls them from your shapelib. */
stdmf, /* dmf for STUD decoupling */
studlvl, /* coarse power for STUD+ decoupling */
rf80 = getval("rf80"), /* rf in Hz for 80ppm STUD+ */
bw, ofs, ppm, /* temporary Pbox parameters */
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
rf0, /* maximum fine power when using pwC pulses */
/* p_d is used to calculate the isotropic mixing on the Cab region */
spinlock = getval("spinlock"), /* DIPSI-3 spinlock field strength in Hz */
p_d, /* 50 degree pulse for DIPSI-2 at rfd */
rfd, /* fine power for 7 kHz rf for 500MHz magnet */
ncyc = getval("ncyc"), /* no. of cycles of DIPSI-3 */
/* the following pulse lengths for SLP pulses are automatically calculated */
/* by the macro "ghcch_tocsy" . SLP pulse shapes, "offC10" etc are called */
/* directly from your shapelib. */
pwC10, /* 180 degree selective sinc pulse on CO(174ppm) */
pwZ, /* the largest of pwC10 and 2.0*pwN */
rf10, /* fine power for the pwC10 ("offC10") pulse */
compC = getval("compC"), /* adjustment for C13 amplifier compression */
pwNlvl = getval("pwNlvl"), /* power for N15 pulses */
pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */
sw1 = getval("sw1"),
sw2 = getval("sw2"),
gt1 = getval("gt1"), /* coherence pathway gradients */
gzcal = getval("gzcal"), /* G/cm to DAC coversion factor*/
gzlvl1 = getval("gzlvl1"),
gzlvl2 = getval("gzlvl2"),
gt3 = getval("gt3"), /* other gradients */
gt5 = getval("gt5"),
gzlvl3 = getval("gzlvl3"),
gzlvl4 = getval("gzlvl4"),
gzlvl5 = getval("gzlvl5"),
gzlvl6 = getval("gzlvl6");
getstr("STUD",STUD);
getstr("mag_flg",mag_flg);
getstr("f1180",f1180);
getstr("f2180",f2180);
strcpy(stCdec, "stCdec80");
stdmf = getval("dmf80");
studlvl = pwClvl + 20.0*log10(compC*pwC*4.0*rf80);
studlvl = (int) (studlvl + 0.5);
P_getreal(GLOBAL,"BPpwrlimits",&BPpwrlimits,1);
P_getreal(GLOBAL,"BPdpwrspinlock",&BPdpwrspinlock,1);
/* LOAD PHASE TABLE */
settable(t3,2,phi3);
settable(t6,1,phi6);
settable(t5,4,phi5);
settable(t10,1,phi10);
settable(t11,4,rec);
/* INITIALIZE VARIABLES */
if (BPpwrlimits > 0.5)
{
if (spinlock > BPdpwrspinlock)
{
spinlock = BPdpwrspinlock;
printf("spinlock too large, reset to user-defined limit (BPdpwrspinlock)");
psg_abort(1);
}
}
if( dpwrf < 4095 )
{ printf("reset dpwrf=4095 and recalibrate C13 90 degree pulse");
psg_abort(1); }
/* maximum fine power for pwC pulses */
rf0 = 4095.0;
setautocal(); /* activate auto-calibration flags */
if (autocal[0] == 'n')
{
/* "offC10": 180 degree one-lobe sinc pulse on CO, null at Ca 139ppm away */
pwC10 = getval("pwC10");
rf10 = (compC*4095.0*pwC*2.0*1.65)/pwC10; /* needs 1.65 times more */
rf10 = (int) (rf10 + 0.5); /* power than a square pulse */
if( pwC > (24.0e-6*600.0/sfrq) )
{ printf("Increase pwClvl so that pwC < 24*600/sfrq");
psg_abort(1);
}
}
else /* if autocal = 'y'(yes), 'q'(quiet), r(read), or 's'(semi) */
{
if(FIRST_FID) /* call Pbox */
{
ppm = getval("dfrq");
bw = 118.0*ppm; ofs = 139.0*ppm;
offC10 = pbox_make("offC10", "sinc180n", bw, ofs, compC*pwC, pwClvl);
if(dm3[B] == 'y') H2ofs = 3.2;
ofs_check(H1ofs, C13ofs, N15ofs, H2ofs);
}
rf10 = offC10.pwrf; pwC10 = offC10.pw;
}
/* dipsi-3 decoupling on CbCa */
p_d = (5.0)/(9.0*4.0*spinlock); /* DIPSI-3 Field Strength */
rfd = (compC*4095.0*pwC*5.0)/(p_d*9.0);
rfd = (int) (rfd + 0.5);
ncyc = (int) (ncyc + 0.5);
/* CHECK VALIDITY OF PARAMETER RANGES */
if( gt1 > 0.5*del - 1.0e-4)
{
printf(" gt1 is too big. Make gt1 less than %f.\n", (0.5*del - 1.0e-4));
psg_abort(1);
}
if( dm[A] == 'y' )
{
printf("incorrect dec1 decoupler flag! Should be 'nny' or 'nnn' ");
psg_abort(1);
}
if((dm2[A] == 'y' || dm2[C] == 'y'))
{
printf("incorrect dec2 decoupler flags! Should be 'nnn' ");
psg_abort(1);
}
if((dm3[A] == 'y' || dm3[C] == 'y'))
{
printf("incorrect dec3 decoupler flags! Should be 'nnn' or 'nyn' ");
psg_abort(1);
}
if( dpwr > 52 )
{
printf("don't fry the probe, DPWR too large! ");
psg_abort(1);
}
if( pw > 50.0e-6 )
{
printf("dont fry the probe, pw too high ! ");
psg_abort(1);
}
if( pwN > 100.0e-6 )
{
printf("dont fry the probe, pwN too high ! ");
psg_abort(1);
}
/* PHASES AND INCREMENTED TIMES */
/* Phase incrementation for hypercomplex 2D data, States-Haberkorn element */
icosel1 = -1; icosel2 = -1;
if (phase1 == 2)
{ tsadd(t6,2,4); icosel1 = -1*icosel1; }
if (phase2 == 2)
{ tsadd(t10,2,4); icosel2 = -1*icosel2; tsadd(t6,2,4); }
/* Set up f1180 */
tau1 = d2;
if((f1180[A] == 'y') && (ni > 1.0))
{ tau1 += ( 1.0 / (2.0*sw1) ); if(tau1 < 0.2e-6) tau1 = 0.0; }
tau1 = tau1/2.0;
/* Set up f2180 */
tau2 = d3;
if((f2180[A] == 'y') && (ni2 > 1.0))
{ tau2 += ( 1.0 / (2.0*sw2) ); if(tau2 < 0.2e-6) tau2 = 0.0; }
tau2 = tau2/2.0;
/* Calculate modifications to phases for States-TPPI acquisition */
if( ix == 1) d2_init = d2;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if(t1_counter % 2)
{ tsadd(t3,2,4); tsadd(t11,2,4); }
if( ix == 1) d3_init = d3;
t2_counter = (int) ( (d3-d3_init)*sw2 + 0.5 );
if(t2_counter % 2)
{ tsadd(t5,2,4); tsadd(t11,2,4); }
/* BEGIN PULSE SEQUENCE */
status(A);
if ( dm3[B] == 'y' )
lk_sample();
if ((ni/sw1-d2)>0)
delay(ni/sw1-d2); /*decreases as t1 increases for const.heating*/
if ((ni2/sw2-d3)>0)
delay(ni2/sw2-d3); /*decreases as t2 increases for const.heating*/
delay(d1);
if ( dm3[B] == 'y' )
{ lk_hold(); lk_sampling_off();} /*freezes z0 correction, stops lock pulsing*/
rcvroff();
obspower(tpwr);
decpower(pwClvl);
dec2power(pwNlvl);
decpwrf(rf0);
obsoffset(tof);
txphase(t3);
delay(1.0e-5);
decrgpulse(pwC, zero, 0.0, 0.0); /*destroy C13 magnetization*/
zgradpulse(gzlvl1, 0.5e-3);
delay(1.0e-4);
decrgpulse(pwC, one, 0.0, 0.0);
zgradpulse(0.7*gzlvl1, 0.5e-3);
delay(5.0e-4);
if ( dm3[B] == 'y' ) /* begins optional 2H decoupling */
{
dec3rgpulse(1/dmf3,one,10.0e-6,2.0e-6);
dec3unblank();
dec3phase(zero);
delay(2.0e-6);
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
}
rgpulse(pw, t3, 0.0, 0.0); /* 1H pulse excitation */
decphase(zero);
delay(0.5*del + tau1 - 2.0*pwC);
decrgpulse(2.0*pwC, zero, 0.0, 0.0);
txphase(zero);
delay(tau1);
rgpulse(2.0*pw, zero, 0.0, 0.0);
if (mag_flg[A] == 'y')
{
magradpulse(icosel1*gzcal*gzlvl1,0.1*gt1);
}
else
{
zgradpulse(icosel1*gzlvl1, 0.1*gt1);
}
decphase(t5);
delay(0.5*del - 0.1*gt1);
simpulse(pw, pwC, zero, t5, 0.0, 0.0);
zgradpulse(gzlvl3, gt3);
decphase(zero);
delay(0.5*del2 - gt3);
simpulse(2.0*pw, 2.0*pwC, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl3, gt3);
txphase(t6);
decphase(one);
delay(0.5*del2 - gt3);
simpulse(pw, pwC, t6, one, 0.0, 0.0);
zgradpulse(gzlvl4, gt3);
txphase(zero);
decphase(zero);
delay(0.5*del1 - gt3);
simpulse(2.0*pw, 2.0*pwC, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl4, gt3);
delay(0.5*del1 - gt3);
decrgpulse(pwC, zero, 0.0, 0.0);
decpwrf(rfd);
delay(2.0e-6);
initval(ncyc, v2);
starthardloop(v2);
decrgpulse(4.9*p_d,zero,0.0,0.0);
decrgpulse(7.9*p_d,two,0.0,0.0);
decrgpulse(5.0*p_d,zero,0.0,0.0);
decrgpulse(5.5*p_d,two,0.0,0.0);
decrgpulse(0.6*p_d,zero,0.0,0.0);
decrgpulse(4.6*p_d,two,0.0,0.0);
decrgpulse(7.2*p_d,zero,0.0,0.0);
decrgpulse(4.9*p_d,two,0.0,0.0);
decrgpulse(7.4*p_d,zero,0.0,0.0);
decrgpulse(6.8*p_d,two,0.0,0.0);
decrgpulse(7.0*p_d,zero,0.0,0.0);
decrgpulse(5.2*p_d,two,0.0,0.0);
decrgpulse(5.4*p_d,zero,0.0,0.0);
decrgpulse(0.6*p_d,two,0.0,0.0);
decrgpulse(4.5*p_d,zero,0.0,0.0);
decrgpulse(7.3*p_d,two,0.0,0.0);
decrgpulse(5.1*p_d,zero,0.0,0.0);
decrgpulse(7.9*p_d,two,0.0,0.0);
decrgpulse(4.9*p_d,two,0.0,0.0);
decrgpulse(7.9*p_d,zero,0.0,0.0);
decrgpulse(5.0*p_d,two,0.0,0.0);
decrgpulse(5.5*p_d,zero,0.0,0.0);
decrgpulse(0.6*p_d,two,0.0,0.0);
decrgpulse(4.6*p_d,zero,0.0,0.0);
decrgpulse(7.2*p_d,two,0.0,0.0);
decrgpulse(4.9*p_d,zero,0.0,0.0);
decrgpulse(7.4*p_d,two,0.0,0.0);
decrgpulse(6.8*p_d,zero,0.0,0.0);
decrgpulse(7.0*p_d,two,0.0,0.0);
decrgpulse(5.2*p_d,zero,0.0,0.0);
decrgpulse(5.4*p_d,two,0.0,0.0);
decrgpulse(0.6*p_d,zero,0.0,0.0);
decrgpulse(4.5*p_d,two,0.0,0.0);
decrgpulse(7.3*p_d,zero,0.0,0.0);
decrgpulse(5.1*p_d,two,0.0,0.0);
decrgpulse(7.9*p_d,zero,0.0,0.0);
decrgpulse(4.9*p_d,two,0.0,0.0);
decrgpulse(7.9*p_d,zero,0.0,0.0);
decrgpulse(5.0*p_d,two,0.0,0.0);
decrgpulse(5.5*p_d,zero,0.0,0.0);
decrgpulse(0.6*p_d,two,0.0,0.0);
decrgpulse(4.6*p_d,zero,0.0,0.0);
decrgpulse(7.2*p_d,two,0.0,0.0);
decrgpulse(4.9*p_d,zero,0.0,0.0);
decrgpulse(7.4*p_d,two,0.0,0.0);
decrgpulse(6.8*p_d,zero,0.0,0.0);
decrgpulse(7.0*p_d,two,0.0,0.0);
decrgpulse(5.2*p_d,zero,0.0,0.0);
decrgpulse(5.4*p_d,two,0.0,0.0);
decrgpulse(0.6*p_d,zero,0.0,0.0);
decrgpulse(4.5*p_d,two,0.0,0.0);
decrgpulse(7.3*p_d,zero,0.0,0.0);
decrgpulse(5.1*p_d,two,0.0,0.0);
decrgpulse(7.9*p_d,zero,0.0,0.0);
decrgpulse(4.9*p_d,zero,0.0,0.0);
decrgpulse(7.9*p_d,two,0.0,0.0);
decrgpulse(5.0*p_d,zero,0.0,0.0);
decrgpulse(5.5*p_d,two,0.0,0.0);
decrgpulse(0.6*p_d,zero,0.0,0.0);
decrgpulse(4.6*p_d,two,0.0,0.0);
decrgpulse(7.2*p_d,zero,0.0,0.0);
decrgpulse(4.9*p_d,two,0.0,0.0);
decrgpulse(7.4*p_d,zero,0.0,0.0);
decrgpulse(6.8*p_d,two,0.0,0.0);
decrgpulse(7.0*p_d,zero,0.0,0.0);
decrgpulse(5.2*p_d,two,0.0,0.0);
decrgpulse(5.4*p_d,zero,0.0,0.0);
decrgpulse(0.6*p_d,two,0.0,0.0);
decrgpulse(4.5*p_d,zero,0.0,0.0);
decrgpulse(7.3*p_d,two,0.0,0.0);
decrgpulse(5.1*p_d,zero,0.0,0.0);
decrgpulse(7.9*p_d,two,0.0,0.0);
endhardloop();
dec2phase(zero);
decphase(zero);
txphase(zero);
decpwrf(rf10);
delay(tau2);
/* WFG3_START_DELAY */
sim3shaped_pulse("", "offC10", "", 2.0*pw, pwC10, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
if(pwC10>2.0*pwN) pwZ=0.0; else pwZ=2.0*pwN - pwC10;
delay(tau2);
decpwrf(rf0);
if (mag_flg[A] == 'y')
{
magradpulse(-icosel2*gzcal*gzlvl2, 1.8*gt1);
}
else
{
zgradpulse(-icosel2*gzlvl2, 1.8*gt1);
}
delay(2.02e-4);
decrgpulse(2.0*pwC, zero, 0.0, 0.0);
decpwrf(rf10);
if (mag_flg[A] == 'y')
{
magradpulse(icosel2*gzcal*gzlvl2, 1.8*gt1);
}
else
{
zgradpulse(icosel2*gzlvl2, 1.8*gt1);
}
delay(2.0e-4 + WFG3_START_DELAY + pwZ);
decshaped_pulse("offC10", pwC10, zero, 0.0, 0.0);
decpwrf(rf0);
decrgpulse(pwC, zero, 2.0e-6, 0.0);
zgradpulse(gzlvl5, gt5);
delay(0.5*del1 - gt5);
simpulse(2.0*pw, 2.0*pwC, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl5, gt5);
txphase(one);
decphase(t10);
delay(0.5*del1 - gt5);
simpulse(pw, pwC, one, t10, 0.0, 0.0);
zgradpulse(gzlvl6, gt5);
txphase(zero);
decphase(zero);
delay(0.5*del2 - gt5);
simpulse(2.0*pw, 2.0*pwC, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl6, gt5);
delay(0.5*del2 - gt5);
simpulse(pw, pwC, zero, zero, 0.0, 0.0);
delay(0.5*del - 0.5*pwC);
simpulse(2.0*pw,2.0*pwC, zero, zero, 0.0, 0.0);
if (mag_flg[A] == 'y')
magradpulse(gzcal*gzlvl1, gt1);
else
zgradpulse(gzlvl1, gt1);
rcvron();
if ((STUD[A]=='n') && (dm[C] == 'y'))
decpower(dpwr);
if ( dm3[B] == 'y' ) /* turns off 2H decoupling */
{
delay(0.5*del-40.0e-6 -gt1 -1/dmf3);
setstatus(DEC3ch, FALSE, 'c', FALSE, dmf3);
dec3rgpulse(1/dmf3,three,2.0e-6,2.0e-6);
dec3blank();
lk_autotrig(); /* resumes lock pulsing */
lk_sample();
if (mag_flg[A] == 'y')
statusdelay(C,40.0e-6 - 2.0*VAGRADIENT_DELAY - POWER_DELAY);
else
statusdelay(C,40.0e-6 - 2.0*GRADIENT_DELAY - POWER_DELAY);
}
else
{
delay(0.5*del-40.0e-6 -gt1);
if (mag_flg[A] == 'y')
statusdelay(C,40.0e-6 - 2.0*VAGRADIENT_DELAY - POWER_DELAY);
else
statusdelay(C,40.0e-6 - 2.0*GRADIENT_DELAY - POWER_DELAY);
}
if ((STUD[A]=='y') && (dm[C] == 'y'))
{decpower(studlvl);
decunblank();
decon();
decprgon(stCdec,1/stdmf, 1.0);
startacq(alfa);
acquire(np, 1.0/sw);
decprgoff();
decoff();
decblank();
}
setreceiver(t11);
}
pulsesequence()
{
/* DECLARE AND LOAD VARIABLES */
char f1180[MAXSTR], /* Flag to start t1 @ halfdwell */
f2180[MAXSTR], /* Flag to start t2 @ halfdwell */
mag_flg[MAXSTR], /* magic-angle coherence transfer gradients */
TROSY[MAXSTR], /* do TROSY on N15 and H1 */
h1dec[MAXSTR], /* Flag to waltz-decouple of H1 for t1*/
CT_c[MAXSTR]; /* Flag to constant time evolution for C13*/
int icosel, /* used to get n and p type */
t1_counter, /* used for states tppi in t1 */
t2_counter, /* used for states tppi in t2 */
ni2 = getval("ni2");
double tau1, /* t1 delay */
tau2, /* t2 delay */
timeTC = getval("timeTC"), /* constant time for 13C evolution */
timeTN = getval("timeTN"), /* constant time for 15N evolution */
kappa = 5.4e-3,
lambda = 2.4e-3,
taud = 1.7e-3,
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
rf0, /* maximum fine power when using pwC pulses */
/* 90 degree pulse at Ca (56ppm), first off-resonance null at CO (174ppm) */
pwC1, /* 90 degree pulse length on C13 at rf1 */
rf1, /* fine power for 4.7 kHz rf for 600MHz magnet */
/* 180 degree pulse at Ca (56ppm), first off-resonance null at CO(174ppm) */
pwC2, /* 180 degree pulse length at rf2 */
rf2, /* fine power for 10.5 kHz rf for 600MHz magnet */
/* the following pulse lengths for SLP pulses are automatically calculated */
/* by the macro "BPcal". SLP pulse shapes, "offC9" etc are called */
/* directly from your shapelib. */
pwC9 = getval("pwC9"), /*180 degree pulse at CO(174ppm) null at Ca(56ppm) */
pwC9a = getval("pwC9a"), /* pwC9a=pwC9, but not set to zero when pwC9=0 */
phshift9, /* phase shift induced on Ca by pwC9 ("offC9") pulse */
pwZ, /* the largest of pwC9 and 2.0*pwN */
pwZ1, /* the larger of pwC9a and 2.0*pwN for 1D experiments */
rf9, /* fine power for the pwC9 ("offC9") pulse */
compH = getval("compH"), /* adjustment for C13 amplifier compression */
compC = getval("compC"), /* adjustment for C13 amplifier compression */
pwHs = getval("pwHs"), /* H1 90 degree pulse length at tpwrs */
tpwrs, /* power for the pwHs ("H2Osinc") pulse */
pwHd, /* H1 90 degree pulse length at tpwrd */
tpwrd, /* rf for WALTZ decoupling */
waltzB1 = getval("waltzB1"), /* waltz16 field strength (in Hz) */
pwNlvl = getval("pwNlvl"), /* power for N15 pulses */
pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */
sw1 = getval("sw1"),
sw2 = getval("sw2"),
gt1 = getval("gt1"), /* coherence pathway gradients */
gzcal = getval("gzcal"), /* g/cm to DAC conversion factor */
gzlvl1 = getval("gzlvl1"),
gzlvl2 = getval("gzlvl2"),
gt0 = getval("gt0"), /* other gradients */
gt3 = getval("gt3"),
gt4 = getval("gt4"),
gt5 = getval("gt5"),
gt7 = getval("gt7"),
gstab = getval("gstab"),
gzlvl0 = getval("gzlvl0"),
gzlvl3 = getval("gzlvl3"),
gzlvl4 = getval("gzlvl4"),
gzlvl5 = getval("gzlvl5"),
gzlvl6 = getval("gzlvl6"),
gzlvl7 = getval("gzlvl7");
getstr("f1180",f1180);
getstr("f2180",f2180);
getstr("mag_flg",mag_flg);
getstr("TROSY",TROSY);
getstr("h1dec",h1dec);
getstr("CT_c",CT_c);
/* LOAD PHASE TABLE */
settable(t3,2,phi3);
settable(t4,1,phx);
settable(t5,4,phi5);
if (TROSY[A]=='y')
{settable(t8,1,phy);
settable(t9,1,phx);
settable(t10,1,phy);
settable(t11,1,phx);
settable(t12,4,recT);}
else
{settable(t8,1,phx);
settable(t9,8,phi9);
settable(t10,1,phx);
settable(t11,1,phy);
settable(t12,4,rec);}
/* INITIALIZE VARIABLES */
if( dpwrf < 4095 )
{ printf("reset dpwrf=4095 and recalibrate C13 90 degree pulse");
psg_abort(1); }
/* maximum fine power for pwC pulses */
rf0 = 4095.0;
/* 90 degree pulse on Ca, null at CO 118ppm away */
pwC1 = sqrt(15.0)/(4.0*118.0*dfrq);
rf1 = (compC*4095.0*pwC)/pwC1;
rf1 = (int) (rf1 + 0.5);
/* 180 degree pulse on Ca, null at CO 118ppm away */
pwC2 = sqrt(3.0)/(2.0*118.0*dfrq);
rf2 = (4095.0*compC*pwC*2.0)/pwC2;
rf2 = (int) (rf2 + 0.5);
if( rf2 > 4095.0 )
{printf("increase pwClvl so that C13 90 < 24us*(600/sfrq)"); psg_abort(1);}
/* 180 degree one-lobe sinc pulse on CO, null at Ca 118ppm away */
rf9 = (compC*4095.0*pwC*2.0*1.65)/pwC9a; /* needs 1.65 times more */
rf9 = (int) (rf9 + 0.5); /* power than a square pulse */
/* the pwC9 pulse at the middle of t1 */
if ((ni2 > 0.0) && (ni == 1.0)) ni = 0.0;
if (pwC9a > 2.0*pwN) pwZ = pwC9a; else pwZ = 2.0*pwN;
if ((pwC9==0.0) && (pwC9a>2.0*pwN)) pwZ1=pwC9a-2.0*pwN; else pwZ1=0.0;
if (ni > 1) pwC9 = pwC9a;
if ( pwC9 > 0 ) phshift9 = 320.0;
else phshift9 = 0.0;
/* selective H20 one-lobe sinc pulse */
tpwrs = tpwr - 20.0*log10(pwHs/(compH*pw*1.69)); /* needs 1.69 times more */
tpwrs = (int) (tpwrs); /* power than a square pulse */
/* power level and pulse time for WALTZ 1H decoupling */
pwHd = 1/(4.0 * waltzB1) ;
tpwrd = tpwr - 20.0*log10(pwHd/(compH*pw));
tpwrd = (int) (tpwrd + 0.5);
/* CHECK VALIDITY OF PARAMETER RANGES */
if ( 0.5*ni*1/(sw1) > timeTC)
{ printf(" ni is too big. Make ni less than %d . Check by using dps and make sure no ? appears for d2=t1max (ni/sw1).\n",
((int)((timeTC)*2.0*sw1-7))); psg_abort(1); }
if ( 0.5*ni2*1/(sw2) > timeTN - WFG3_START_DELAY)
{ printf(" ni2 is too big. Make ni2 equal to %d or less.\n",
((int)((timeTN - WFG3_START_DELAY)*2.0*sw2))); psg_abort(1);}
if ( dm[A] == 'y' || dm[B] == 'y' || dm[C] == 'y' )
{ printf("incorrect dec1 decoupler flags! Should be 'nnn' "); psg_abort(1);}
if ( dm2[A] == 'y' || dm2[B] == 'y' )
{ printf("incorrect dec2 decoupler flags! Should be 'nny' "); psg_abort(1);}
if ( dm3[A] == 'y' || dm3[C] == 'y' )
{ printf("incorrect dec3 decoupler flags! Should be 'nyn' or 'nnn' ");
psg_abort(1);}
if ( dpwr2 > 46 )
{ printf("dpwr2 too large! recheck value "); psg_abort(1);}
if ( pw > 20.0e-6 )
{ printf(" pw too long ! recheck value "); psg_abort(1);}
if ( pwN > 100.0e-6 )
{ printf(" pwN too long! recheck value "); psg_abort(1);}
if ( TROSY[A]=='y' && dm2[C] == 'y')
{ text_error("Choose either TROSY='n' or dm2='n' ! "); psg_abort(1);}
/* PHASES AND INCREMENTED TIMES */
/* Phase incrementation for hypercomplex 2D data, States-Haberkorn element */
if (phase1 == 2) tsadd(t3,1,4);
if (TROSY[A]=='y')
{ if (phase2 == 2) icosel = +1;
else {tsadd(t4,2,4); tsadd(t10,2,4); icosel = -1;}
}
else { if (phase2 == 2) {tsadd(t10,2,4); icosel = +1;}
else icosel = -1;
}
/* Set up f1180 */
tau1 = d2;
if((f1180[A] == 'y') && (ni > 1.0))
{ tau1 += ( 1.0 / (2.0*sw1) ); if(tau1 < 0.2e-6) tau1 = 0.0; }
tau1 = tau1/2.0;
/* Set up f2180 */
tau2 = d3;
if((f2180[A] == 'y') && (ni2 > 1.0))
{ tau2 += ( 1.0 / (2.0*sw2) ); if(tau2 < 0.2e-6) tau2 = 0.0; }
tau2 = tau2/2.0;
/* Calculate modifications to phases for States-TPPI acquisition */
if( ix == 1) d2_init = d2;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if(t1_counter % 2)
{ tsadd(t3,2,4); tsadd(t12,2,4); }
if( ix == 1) d3_init = d3;
t2_counter = (int) ( (d3-d3_init)*sw2 + 0.5 );
if(t2_counter % 2)
{ tsadd(t8,2,4); tsadd(t12,2,4); }
/* BEGIN PULSE SEQUENCE */
status(A);
delay(d1);
if ( dm3[B] == 'y' )
{ lk_hold(); lk_sampling_off();} /*freezes z0 correction, stops lock pulsing*/
rcvroff();
obspower(tpwr);
decpower(pwClvl);
dec2power(pwNlvl);
decpwrf(rf0);
obsoffset(tof);
txphase(zero);
delay(1.0e-5);
dec2rgpulse(pwN, zero, 0.0, 0.0); /*destroy N15 and C13 magnetization*/
decrgpulse(pwC, zero, 0.0, 0.0);
zgradpulse(gzlvl0, 0.5e-3);
delay(1.0e-4);
dec2rgpulse(pwN, one, 0.0, 0.0);
decrgpulse(pwC, zero, 0.0, 0.0);
zgradpulse(0.7*gzlvl0, 0.5e-3);
delay(5.0e-4);
rgpulse(pw,zero,0.0,0.0); /* 1H pulse excitation */
dec2phase(zero);
zgradpulse(gzlvl0, gt0);
delay(lambda - gt0);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
txphase(one);
zgradpulse(gzlvl0, gt0);
delay(lambda - gt0);
rgpulse(pw, one, 0.0, 0.0);
if (TROSY[A]=='y')
{
txphase(two);
obspower(tpwrs);
shaped_pulse("H2Osinc",pwHs,two,5.0e-4,0.0);
obspower(tpwr);
zgradpulse(gzlvl3, gt3);
delay(2.0e-4);
dec2rgpulse(pwN, zero, 0.0, 0.0);
delay(0.5*kappa - 2.0*pw);
rgpulse(2.0*pw, two, 0.0, 0.0);
dec2phase(zero);
decpwrf(rf2);
delay(timeTN - 0.5*kappa);
}
else
{
txphase(zero);
obspower(tpwrs);
shaped_pulse("H2Osinc",pwHs,zero,5.0e-4,0.0);
obspower(tpwrd);
zgradpulse(gzlvl3, gt3);
delay(2.0e-4);
dec2rgpulse(pwN, zero, 0.0, 0.0);
txphase(one);
delay(kappa - pwHd - 2.0e-6 - PRG_START_DELAY);
rgpulse(pwHd,one,0.0,0.0);
txphase(zero);
delay(2.0e-6);
obsprgon("waltz16", pwHd, 90.0); /* PRG_START_DELAY */
xmtron();
decphase(zero);
dec2phase(zero);
decpwrf(rf2);
delay(timeTN - kappa);
}
sim3pulse(0.0, pwC2, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
decphase(t3);
decpwrf(rf1);
delay(timeTN);
dec2rgpulse(pwN, zero, 0.0, 0.0);
if (TROSY[A]=='n')
{
xmtroff();
obsprgoff();
if (h1dec[0]=='y')
rgpulse(pwHd,three,2.0e-6,0.0);
else
rgpulse(pwHd,one,2.0e-6,0.0);
}
zgradpulse(gzlvl3, gt3);
txphase(one);
delay(2.0e-4);
if(h1dec[0]=='y')
{
obspower(tpwrd);
rgpulse(pwHd,one,0.0,0.0);
txphase(zero);
delay(2.0e-6);
obsprgon("waltz16", pwHd, 90.0);
xmtron();
}
if ( dm3[B] == 'y' ) /* begins optional 2H decoupling */
{
dec3rgpulse(1/dmf3,one,10.0e-6,2.0e-6);
dec3unblank();
dec3phase(zero);
delay(2.0e-6);
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
}
decrgpulse(pwC1,t3,0.0,0.0);
decphase(zero);
/* xxxxxxxxxxxxxxxxxxxxxx 13Ca EVOLUTION xxxxxxxxxxxxxxxxxx */
if (CT_c[0]=='n') {
if ((ni>1.0) && (tau1>0.0)) /* total 13C evolution equals d2 exactly */
{ /* 2.0*pwC1/PI compensates for evolution at 64% rate duting pwC1 */
decpwrf(rf9);
if(tau1 - 2.0*pwC1/PI - WFG3_START_DELAY - 0.5*pwZ > 0.0)
{
delay(tau1 - 2.0*pwC1/PI - WFG3_START_DELAY - 0.5*pwZ);
/* WFG3_START_DELAY */
sim3shaped_pulse("", "offC9", "", 0.0, pwC9a, 2.0*pwN, zero, zero, zero,
0.0, 0.0);
initval(phshift9, v9);
decstepsize(1.0);
dcplrphase(v9); /* SAPS_DELAY */
delay(tau1 - 2.0*pwC1/PI - SAPS_DELAY - 0.5*pwZ - 2.0e-6);
}
else
{
initval(180.0, v9);
decstepsize(1.0);
dcplrphase(v9); /* SAPS_DELAY */
delay(2.0*tau1 - 4.0*pwC1/PI - SAPS_DELAY - 2.0e-6);
}
}
else if (ni==1.0) /* special 1D check of pwC9 phase enabled when ni=1 */
{
decpwrf(rf9);
delay(10.0e-6 + SAPS_DELAY + 0.5*pwZ1);
/* WFG3_START_DELAY */
sim3shaped_pulse("", "offC9", "", 0.0, pwC9, 2.0*pwN, zero, zero, zero,
2.0e-6, 0.0);
initval(phshift9, v9);
decstepsize(1.0);
dcplrphase(v9); /* SAPS_DELAY */
delay(10.0e-6 + WFG3_START_DELAY + 0.5*pwZ1);
}
else /* 13Ca evolution refocused for 1st increment */
{
decpwrf(rf2);
decrgpulse(pwC2, zero, 2.0e-6, 0.0);
}
}
else { /* %%%%%%%%%%STARTING 13Ca Constant Time EVOLUTION %%%%%%%%%%%%%%%%%%*/
decpwrf(rf9);
if(tau1 - 2.0*pwC1/PI - WFG_START_DELAY -POWER_DELAY> 0.0) {
delay(tau1 -2.0*pwC1/PI -POWER_DELAY -WFG_START_DELAY);
sim3shaped_pulse("","offC9","",0.0,pwC9a, 2.0*pwN, zero, zero, zero,
0.0, 0.0);
}
else {
sim3shaped_pulse("","offC9","",0.0,pwC9a, 2.0*pwN, zero, zero, zero,
0.0, 0.0);
}
if (h1dec[0]=='n'){
delay(taud-POWER_DELAY);
obspower(tpwr);
rgpulse(2.0*pw,zero,0.0,0.0);
if ( dm3[B] == 'y' ) /* turns off 2H decoupling */
{
delay(timeTC -pwZ -2.0*WFG_STOP_DELAY -taud -2.0*pw -1/dmf3 -2.0e-6 -202.0e-6 -gt7);
setstatus(DEC3ch, FALSE, 'c', FALSE, dmf3);
dec3rgpulse(1/dmf3,three,2.0e-6,2.0e-6);
dec3blank();
}
else{ /* Should be forbidden?? */
delay(timeTC -pwZ -WFG_STOP_DELAY -taud -2.0*pw -202.0e-6 -gt7);
}
}
else { /* hdec=y */
if ( dm3[B] == 'y' ) /* turns off 2H decoupling */
{
delay(timeTC -pwZ -2.0*WFG_STOP_DELAY -PRG_STOP_DELAY -pwHd -1/dmf3
-4.0e-6-202.0e-6-gt7);
xmtroff();
obsprgoff();
rgpulse(pwHd,three,2.0e-6,2.0e-6);
setstatus(DEC3ch, FALSE, 'c', FALSE, dmf3);
dec3rgpulse(1/dmf3,three,2.0e-6,2.0e-6);
dec3blank();
}
else{
delay(timeTC -pwZ -WFG_STOP_DELAY -PRG_STOP_DELAY -4.0e-6 -202.0e-6
-gt7);
xmtroff();
obsprgoff();
rgpulse(pwHd,three,2.0e-6,2.0e-6);
}
}
delay(2.0e-6);
zgradpulse(gzlvl7,gt7);
delay(200.0e-6-POWER_DELAY);
decpwrf(rf2);
decrgpulse(pwC2, zero, 0.0, 0.0); /* 13Ca 180 degree pulse */
delay(2.0e-6);
zgradpulse(gzlvl7,gt7);
delay(200.0e-6);
if (h1dec[0]=='n') {
if ( dm3[B] == 'y' ) /* begins optional 2H decoupling */
{
dec3rgpulse(1/dmf3,one,10.0e-6,2.0e-6);
dec3unblank();
dec3phase(zero);
delay(2.0e-6);
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
delay(timeTC-tau1-202.0e-6-gt7-2.0*WFG_START_DELAY-1/dmf3-
2.0*POWER_DELAY-pwC9a-2.0e-6-WFG_STOP_DELAY-SAPS_DELAY);
}
else{ /* Should be forbidden??? */
delay(timeTC -tau1 - 202.0e-6 - gt7-2.0*POWER_DELAY-pwC9a-
WFG_START_DELAY-WFG_STOP_DELAY-2.0e-6-SAPS_DELAY);
}
}
else {
if (dm3[B]=='y') {
rgpulse(pwHd,one,0.0,0.0);
txphase(zero);
delay(2.0e-6);
obsprgon("waltz16", pwHd, 90.0);
xmtron();
dec3rgpulse(1/dmf3,one,10.0e-6,2.0e-6);
dec3unblank();
dec3phase(zero);
delay(2.0e-6);
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
delay(timeTC-tau1-202.0e-6-gt7-2.0*WFG_START_DELAY-4.0e-6-1/dmf3-pwHd-
PRG_START_DELAY-2.0*POWER_DELAY-pwC9a-2.0e-6-SAPS_DELAY);
}
else {
delay(2.0e-6);
rgpulse(pwHd,one,0.0,0.0);
txphase(zero);
delay(2.0e-6);
obsprgon("waltz16", pwHd, 90.0);
xmtron();
delay(timeTC-tau1-202.0e-6-gt7-4.0e-6-pwHd-PRG_START_DELAY-
2.0*POWER_DELAY-pwC9a-WFG_START_DELAY-WFG_STOP_DELAY-SAPS_DELAY);
}
}
decpwrf(rf9);
decshaped_pulse("offC9",pwC9a,zero,0.0,0.0);
initval(phshift9, v9);
decstepsize(1.0);
dcplrphase(v9); /* SAPS_DELAY */
} /* %%%%%%%%%%%%%%%%%%ENDING 13Ca Constant Time EVOLUTION %%%%%%%%%%%%%%%%%%*/
decphase(t5);
decpwrf(rf1);
decrgpulse(pwC1, t5, 2.0e-6, 0.0);
dec2phase(t8);
dcplrphase(zero);
if ( dm3[B] == 'y' ) /* turns off 2H decoupling */
{
setstatus(DEC3ch, FALSE, 'c', FALSE, dmf3);
dec3rgpulse(1/dmf3,three,2.0e-6,2.0e-6);
dec3blank();
lk_autotrig(); /* resumes lock pulsing */
}
if (h1dec[0]=='y')
{
xmtroff();
obsprgoff();
rgpulse(pwHd,three,2.0e-6,0.0);
txphase(one);
}
delay(2.0e-6);
zgradpulse(gzlvl4, gt4);
delay(2.0e-4);
if (TROSY[A]=='n') {
rgpulse(pwHd,one,0.0,0.0);
txphase(zero);
delay(2.0e-6);
obsprgon("waltz16", pwHd, 90.0);
xmtron();
}
/* %%%%%%%%%%%%%%%%%%STARTING N15 Constant Time Evolution %%%%%%%%%%%%%%%%%%*/
dec2rgpulse(pwN, t8, 0.0, 0.0);
decphase(zero);
dec2phase(t9);
decpwrf(rf2);
delay(timeTN - tau2);
sim3pulse(0.0, pwC2, 2.0*pwN, zero, zero, t9, 0.0, 0.0);
dec2phase(t10);
decpwrf(rf9);
if (TROSY[A]=='y')
{ if (tau2 > gt1 + 2.0*GRADIENT_DELAY + 1.5e-4 + pwHs)
{
txphase(three);
delay(timeTN - pwC9a - WFG_START_DELAY); /* WFG_START_DELAY */
decshaped_pulse("offC9", pwC9a, zero, 0.0, 0.0);
delay(tau2 - gt1 - 2.0*GRADIENT_DELAY - 1.5e-4 - pwHs);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspower(tpwrs); /* POWER_DELAY */
delay(1.0e-4 - POWER_DELAY);
shaped_pulse("H2Osinc", pwHs, three, 0.0, 0.0);
txphase(t4);
obspower(tpwr); /* POWER_DELAY */
delay(0.5e-4 - POWER_DELAY);
}
else if (tau2 > pwHs + 0.5e-4)
{
txphase(three);
delay(timeTN-pwC9a-WFG_START_DELAY-gt1-2.0*GRADIENT_DELAY-1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspower(tpwrs); /* POWER_DELAY */
delay(1.0e-4 - POWER_DELAY); /* WFG_START_DELAY */
decshaped_pulse("offC9", pwC9a, zero, 0.0, 0.0);
delay(tau2 - pwHs - 0.5e-4);
shaped_pulse("H2Osinc", pwHs, three, 0.0, 0.0);
txphase(t4);
obspower(tpwr); /* POWER_DELAY */
delay(0.5e-4 - POWER_DELAY);
}
else
{
txphase(three);
delay(timeTN - pwC9a - WFG_START_DELAY - gt1 - 2.0*GRADIENT_DELAY
- 1.5e-4 - pwHs);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspower(tpwrs); /* POWER_DELAY */
delay(1.0e-4 - POWER_DELAY); /* WFG_START_DELAY */
shaped_pulse("H2Osinc", pwHs, three, 0.0, 0.0);
txphase(t4);
obspower(tpwr); /* POWER_DELAY */
delay(0.5e-4 - POWER_DELAY);
decshaped_pulse("offC9", pwC9a, zero, 0.0, 0.0);
delay(tau2);
}
}
else
{
if (tau2 > kappa)
{
delay(timeTN - pwC9a - WFG_START_DELAY); /* WFG_START_DELAY */
decshaped_pulse("offC9", pwC9a, zero, 0.0, 0.0);
delay(tau2 - kappa - PRG_STOP_DELAY - pwHd - 2.0e-6);
xmtroff();
obsprgoff(); /* PRG_STOP_DELAY */
rgpulse(pwHd,three,2.0e-6,0.0);
txphase(t4);
delay(kappa - gt1 - 2.0*GRADIENT_DELAY - 1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspower(tpwr); /* POWER_DELAY */
delay(1.0e-4 - POWER_DELAY);
}
else if (tau2 > (kappa - pwC9a - WFG_START_DELAY))
{
delay(timeTN + tau2 - kappa - PRG_STOP_DELAY - pwHd - 2.0e-6);
xmtroff();
obsprgoff(); /* PRG_STOP_DELAY */
rgpulse(pwHd,three,2.0e-6,0.0);
txphase(t4); /* WFG_START_DELAY */
decshaped_pulse("offC9", pwC9a, zero, 0.0, 0.0);
delay(kappa -pwC9a -WFG_START_DELAY -gt1 -2.0*GRADIENT_DELAY -1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspower(tpwr); /* POWER_DELAY */
delay(1.0e-4 - POWER_DELAY);
}
else if (tau2 > gt1 + 2.0*GRADIENT_DELAY + 1.0e-4)
{
delay(timeTN + tau2 - kappa - PRG_STOP_DELAY - pwHd - 2.0e-6);
xmtroff();
obsprgoff(); /* PRG_STOP_DELAY */
rgpulse(pwHd,three,2.0e-6,0.0);
txphase(t4);
delay(kappa - tau2 - pwC9a - WFG_START_DELAY); /* WFG_START_DELAY */
decshaped_pulse("offC9", pwC9a, zero, 0.0, 0.0);
delay(tau2 - gt1 - 2.0*GRADIENT_DELAY - 1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspower(tpwr); /* POWER_DELAY */
delay(1.0e-4 - POWER_DELAY);
}
else
{
delay(timeTN + tau2 - kappa - PRG_STOP_DELAY - pwHd - 2.0e-6);
xmtroff();
obsprgoff(); /* PRG_STOP_DELAY */
rgpulse(pwHd,three,2.0e-6,0.0);
txphase(t4);
delay(kappa-tau2-pwC9a-WFG_START_DELAY-gt1-2.0*GRADIENT_DELAY-1.0e-4);
if (mag_flg[A]=='y') magradpulse(gzcal*gzlvl1, gt1);
else zgradpulse(gzlvl1, gt1); /* 2.0*GRADIENT_DELAY */
obspower(tpwr); /* POWER_DELAY */
delay(1.0e-4 - POWER_DELAY); /* WFG_START_DELAY */
decshaped_pulse("offC9", pwC9a, zero, 0.0, 0.0);
delay(tau2);
}
}
/* xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx */
if (TROSY[A]=='y') rgpulse(pw, t4, 0.0, 0.0);
else sim3pulse(pw, 0.0, pwN, t4, zero, t10, 0.0, 0.0);
txphase(zero);
dec2phase(zero);
zgradpulse(gzlvl5, gt5);
if (TROSY[A]=='y') delay(lambda - 0.65*(pw + pwN) - gt5);
else delay(lambda - 1.3*pwN - gt5);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl5, gt5);
txphase(one);
dec2phase(t11);
delay(lambda - 1.3*pwN - gt5);
sim3pulse(pw, 0.0, pwN, one, zero, t11, 0.0, 0.0);
txphase(zero);
dec2phase(zero);
zgradpulse(gzlvl6, gt5);
delay(lambda - 1.3*pwN - gt5);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
dec2phase(t10);
zgradpulse(gzlvl6, gt5);
if (TROSY[A]=='y') delay(lambda - 1.6*pwN - gt5);
else delay(lambda - 0.65*pwN - gt5);
if (TROSY[A]=='y') dec2rgpulse(pwN, t10, 0.0, 0.0);
else rgpulse(pw, zero, 0.0, 0.0);
delay((gt1/10.0) + 1.0e-4 +gstab - 0.5*pw + 2.0*GRADIENT_DELAY + POWER_DELAY);
rgpulse(2.0*pw, zero, 0.0, rof1);
dec2power(dpwr2); /* POWER_DELAY */
if (mag_flg[A] == 'y') magradpulse(icosel*gzcal*gzlvl2, gt1/10.0);
else zgradpulse(icosel*gzlvl2, gt1/10.0); /* 2.0*GRADIENT_DELAY */
delay(gstab);
rcvron();
statusdelay(C,1.0e-4 - rof1);
if (dm3[B]=='y') lk_sample();
setreceiver(t12);
}
pulsesequence()
{
/* DECLARE AND LOAD VARIABLES */
char
CA90_in_str[MAXSTR],
CA180_in_str[MAXSTR], CA180n_in_str[MAXSTR],
CO180offCA_in_str[MAXSTR],
RFpars[MAXSTR],
exp_mode[MAXSTR], /* flag to run 3D, or 2D time-shared 15N TROSY /13C HSQC-SE*/
f1180[MAXSTR], /* Flag to start t1 @ halfdwell */
f2180[MAXSTR],
f3180[MAXSTR]; /* do TROSY on N15 and H1 */
int icosel=1.0; /* used to get n and p type */
double x,y,z, t2max, t1max, tpwrs,
tpwrsf_d = getval("tpwrsf_d"), /* fine power adustment for first soft pulse(down)*/
tpwrsf_u = getval("tpwrsf_u"), /* fine power adustment for second soft pulse(up) */
pwHs = getval("pwHs"), /* H1 90 degree pulse length at tpwrs */
compH =getval("compH"),
tau1, tau2, /*evolution times in indirect dimensions */
ni2=getval("ni2"),
tauNH=getval("tauNH"), /* 1/(4Jhn), INEPTs, 2.4ms*/
tauNH1=getval("tauNH1"), /* 1/(4Jhn), TROSY in CN CT, 2.7ms*/
timeTN1=getval("timeTN1"), /* CT time for (first) N->CA*N transfer */
timeTN=getval("timeTN"), /* CT time for last SE TROSY */
timeCN=getval("timeCN"), /* CT time for CA -> N transfer, middle */
pwClvl = getval("pwClvl"), /* coarse power for C13 pulse */
pwC = getval("pwC"), /* C13 90 degree pulse length at pwClvl */
compC = getval("compC"),
dfrq = getval("dfrq"),
pwNlvl = getval("pwNlvl"), /* power for N15 pulses */
pwN = getval("pwN"), /* N15 90 degree pulse length at pwNlvl */
gstab = getval("gstab"),
g6bal= getval("g6bal"),
/* balance of the decoding gradient around last 180 pulse on 1H
g6bal=1.0 : full g6 is on the right side of the last pw180 on 1H
g6bal=0.0: full g6 is on the left side*/
gt0 = getval("gt0"),
gt1 = getval("gt1"),
gt2 = getval("gt2"),
gt3 = getval("gt3"),
gt4 = getval("gt4"),
gt5 = getval("gt5"),
gt6 = getval("gt6"),
gt7 = getval("gt7"),
gzlvl0 = getval("gzlvl0"),
gzlvl1 = getval("gzlvl1"),
gzlvl2 = getval("gzlvl2"),
gzlvl3 = getval("gzlvl3"),
gzlvl4 = getval("gzlvl4"),
gzlvl5 = getval("gzlvl5"),
gzlvl6 = getval("gzlvl6"),
gzlvl7 = getval("gzlvl7"),
gzlvl11 = getval("gzlvl11");
getstr("f1180",f1180);
getstr("f2180",f2180);
getstr("exp_mode",exp_mode);
tpwrs = tpwr - 20.0*log10(pwHs/(compH*pw*1.69)); /*needs 1.69 times more*/
tpwrs = (int) (tpwrs); /*power than a square pulse */
if (tpwrsf_d<4095.0)
tpwrs=tpwrs+6.0; /* add 6dB to let tpwrsf_d control fine power ~2048*/
/* LOAD PHASE TABLE */
settable(t1,1,phi1);
settable(t2,4,phi2); /* default double trosy */
if (exp_mode[A] == 'h') {settable(t2,4,phi2h);}; /*option for regular hNcaNH */
settable(t3,4,phi3);
settable(t4,8,phi4);
settable(t5,2,phi5);
settable(t6,4,phi6);
settable(t7,4,phi7);
settable(t8,4,phi8);
settable(t21,1,psi1); /*trosy and SE hsqc in reverse INPET */
settable(t22,1,psi2);
settable(t23,1,psi2c);
settable(t31,8,rec);
/* some checks */
if((dm2[A] == 'y') || (dm2[B] == 'y') || (dm2[C] == 'y') || (dm2[D] == 'y'))
{ text_error("incorrect dec2 decoupler flags! Should be 'nnnn' "); psg_abort(1); }
if ( dm3[A] == 'y' || dm3[C] == 'y' )
{ printf("incorrect dec3 decoupler flags! Should be 'nyn' or 'nnn' ");
psg_abort(1);}
if ( dpwr3 > 56 )
{ printf("dpwr3 too large! recheck value "); psg_abort(1);}
if ( (dm3[B] == 'y' ) && (timeCN*2.0 > 60.0e-3) )
{ printf("too lond time for 2H decoupling, SOL ");psg_abort(1);}
/* INITIALIZE VARIABLES */
if(FIRST_FID) /* call Pbox */
{
getstr("CA180_in_str",CA180_in_str); getstr("CA180n_in_str",CA180n_in_str);
getstr("CA90_in_str",CA90_in_str); getstr("CO180offCA_in_str",CO180offCA_in_str);
strcpy(RFpars, "-stepsize 0.5 -attn i");
CA180 = pbox("et_CA180_auto", CA180_in_str, RFpars, dfrq, compC*pwC, pwClvl);
CA180n = pbox("et_CA180n_auto", CA180n_in_str, RFpars, dfrq, compC*pwC, pwClvl);
CA90 = pbox("et_CA90_auto", CA90_in_str, RFpars, dfrq, compC*pwC, pwClvl);
CO180offCA = pbox("et_CO180offCA_auto", CO180offCA_in_str, RFpars, dfrq, compC*pwC, pwClvl);
};
/* Phase incrementation for hypercomplex 2D data, States-Haberkorn element */
/* t1 , N15 */
if (phase1 == 2) {tsadd(t2 ,1,4);}
if(d2_index % 2) {tsadd(t2,2,4); tsadd(t31,2,4); }
/* setting up semi-CT on t1 (ni) dimension */
tau1 = d2;
t1max=(ni-1.0)/sw1;
if((f1180[A] == 'y') && (ni > 0.0))
{tau1 += 0.5/sw1 ; t1max+= 0.5/sw1; }
if( t1max < timeTN1*2.0) {t1max=2.0*timeTN1;};
/* if not enough ni increments, then just regular CT in t1/ni CN */
/* t2, CA */
if (phase2 == 2) { tsadd(t3,1,4); }
if (d3_index % 2) { tsadd(t3,2,4); tsadd(t31,2,4); }
/* setup constant time in t2 (ni2) */
tau2 = d3;
t2max=2.0*(timeCN - CO180offCA.pw);
if((f2180[A] == 'y') && (ni2 > 0.0))
{tau2 += 0.5/sw2 ; t2max += 0.5/sw2 ;}
if(tau2 < 0.2e-6) {tau2 = 0.0;}
if ( (ni2-1.0)/sw2 > t2max)
{ text_error("too many ni2 increments in t2 ! "); psg_abort(1); }
if(FIRST_FID)
{
printf("t1max is %f\n",t1max);
printf("t2max is %f\n",t2max);
};
/* BEGIN PULSE SEQUENCE */
status(A);
obspower(tpwr);
decpower(pwClvl);
dec2power(pwNlvl);
txphase(zero);
decphase(zero);
dec2phase(zero);
delay(d1);
zgradpulse(gzlvl2, gt2);
delay(gstab*3.0);
if (exp_mode[B]=='n') dec2rgpulse(2.0*pwN, zero, 0.0, 0.0); /* test for steady-state 15N */
/* Hz -> HzXz INEPT */
rgpulse(pw,zero,rof1,rof1); /* 1H pulse excitation */
zgradpulse(gzlvl0, gt0);
delay(tauNH -gt0);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
delay(tauNH - gt0 -gstab);
zgradpulse(gzlvl0, gt0);
delay(gstab);
rgpulse(pw, t6, rof1, rof1);
/* on HzNz now */
/* water flipback*/
obspower(tpwrs); obspwrf(tpwrsf_u);
shaped_pulse("H2Osinc",pwHs,zero,rof1,rof1);
obspower(tpwr); obspwrf(4095.0);
/* purge */
zgradpulse(gzlvl3, gt3);
dec2phase(t2);
delay(gstab*2.0);
/* HzNz -> NzCAz +t1 evolution*/
dec2rgpulse(pwN, t2, 0.0, 0.0);
/* double-trosy hNcaNH */
delay(tauNH1 -pwHs-4.0*rof1 -pw
-2.0*POWER_DELAY -WFG_STOP_DELAY-WFG_START_DELAY);
obspower(tpwrs); obspwrf(tpwrsf_d);
shaped_pulse("H2Osinc",pwHs,two,rof1,rof1);
obspower(tpwr); obspwrf(4095.0);
rgpulse(pw, zero, rof1, rof1);
rgpulse(pw, t7, rof1, rof1);
obspower(tpwrs); obspwrf(tpwrsf_u);
shaped_pulse("H2Osinc",pwHs,t8,rof1,rof1);
obspower(tpwr); obspwrf(4095.0);
dec_c13_shpulse(CO180offCA,zero);
delay(tau1*0.5);
dec_c13_shpulse(CO180offCA,zero); dec2phase(zero);
delay( timeTN1 -tauNH1 -pwHs -4.0*rof1 -pw -2.0*POWER_DELAY
-WFG_STOP_DELAY -WFG_START_DELAY -CA180.pw -2.0*CO180offCA.pw
-3.0*(2.0*POWER_DELAY +WFG_STOP_DELAY +WFG_START_DELAY));
dec_c13_shpulse(CA180,zero);
delay(tau1*0.5 -timeTN1*tau1/t1max);
dec2rgpulse(2.0*pwN, zero, 0.0, 0.0);
delay( timeTN1 -tau1*timeTN1/t1max);
dec2rgpulse(pwN, zero, 0.0, 0.0);
/* on CAzNz now */
/* purge */
zgradpulse(gzlvl7, gt7);
delay(gstab);
if(dm3[B] == 'y')
{ dec3unblank();
if(1.0/dmf3>900.0e-6)
{
dec3power(dpwr3+6.0);
dec3rgpulse(0.5/dmf3, one, 1.0e-6, 0.0e-6);
dec3power(dpwr3);
}
else
dec3rgpulse(1.0/dmf3, one, 1.0e-6,0.0e-6);
dec3phase(zero);
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
}
/* dec_c13_shpulse(CA90,t3);*/
/* t2 time, CA evolution */
decrgpulse(pwC,t3,0.0,0.0);
decphase(zero);
delay(0.5*(timeCN+tau2*0.5-CO180offCA.pw) );
dec_c13_shpulse(CO180offCA,zero);
delay(0.5*(timeCN+tau2*0.5-CO180offCA.pw) -pwN*2.0 + WFG_STOP_DELAY);
if (exp_mode[A]=='R') /* test CA.N relaxation rate */
{
delay(2.0*pwN);
}
else
dec2rgpulse(2.0*pwN, zero, 0.0, 0.0);
dec_c13_shpulse(CA180n,zero);
delay(0.5*(timeCN-tau2*0.5-CO180offCA.pw) );
dec_c13_shpulse(CO180offCA,zero);
delay(0.5*(timeCN-tau2*0.5-CO180offCA.pw) + WFG_START_DELAY);
/*dec_c13_shpulse(CA90,zero);*/
decrgpulse(pwC,zero,0.0,0.0);
if(dm3[B] == 'y')
{
setstatus(DEC3ch, FALSE, 'w', FALSE, dmf3);
if(1.0/dmf3>900.0e-6)
{
dec3power(dpwr3+6.0);
dec3rgpulse(0.5/dmf3, three, 1.0e-6, 0.0e-6);
dec3power(dpwr3);
}
else
dec3rgpulse(1.0/dmf3, three, 1.0e-6, 0.0e-6);
dec3blank();
delay(PRG_START_DELAY);
}
zgradpulse(gzlvl5, gt5);
dec2phase(t4);
delay(gstab);
/* CaN->N + back to NH */
dec2rgpulse(pwN, t4, 0.0, 0.0);
dec2phase(zero);
delay(timeTN);
dec2rgpulse(2.0*pwN, zero, 0.0, 0.0);
dec_c13_shpulse(CA180,zero);
delay(timeTN - CA180.pw -gt4-gstab -pwHs-3.0*rof1
-4.0*POWER_DELAY -2.0*WFG_STOP_DELAY-2.0*WFG_START_DELAY
-2.0*GRADIENT_DELAY
+4.0*pwN/3.1415-pw);
zgradpulse(gzlvl4, gt4);
delay(gstab);
/*Water flipback (flipdown actually ) */
obspower(tpwrs); obspwrf(tpwrsf_d);
shaped_pulse("H2Osinc",pwHs,three,rof1,rof1);
obspower(tpwr); obspwrf(4095.0);
/* reverse double INEPT */
/* 90 */
rgpulse(pw, t21, rof1, rof1);
zgradpulse(gzlvl11, gt1);
delay(tauNH -gt1 -rof1
-CA180.pw -2.0*POWER_DELAY - WFG_STOP_DELAY- WFG_START_DELAY );
dec_c13_shpulse(CA180,zero);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
delay(tauNH - gt1 -gstab);
zgradpulse(gzlvl11, gt1);
delay(gstab);
/* 90 */
sim3pulse(pw, 0.0, pwN, one, zero, zero, 0.0, 0.0);
zgradpulse(gzlvl1, gt1);
delay(tauNH -gt1);
sim3pulse(2.0*pw, 0.0, 2.0*pwN, zero, zero, zero, 0.0, 0.0);
delay(tauNH -POWER_DELAY -gt1- gstab);
zgradpulse(gzlvl1, gt1);
dec2phase(t22);
delay(gstab);
sim3pulse(0.0,0.0, pwN, one, zero, t22, 0.0, 0.0);
zgradpulse(-(1.0-g6bal)*gzlvl6*icosel, gt6); /* 2.0*GRADIENT_DELAY */
delay( gstab -pwN*0.5 +pw*(2.0/3.1415-0.5) );
rgpulse(2.0*pw, zero, rof1, rof1);
dec2power(dpwr2); decpower(dpwr);
zgradpulse(g6bal*gzlvl6*icosel, gt6); /* 2.0*GRADIENT_DELAY */
delay(gstab +2.0*POWER_DELAY );
status(C);
setreceiver(t31);
}
pulsesequence()
{
/* DECLARE VARIABLES */
char autocal[MAXSTR], /* auto-calibration flag */
fsat[MAXSTR],
fscuba[MAXSTR],
f1180[MAXSTR], /* Flag to start t1 @ halfdwell */
f2180[MAXSTR], /* Flag to start t2 @ halfdwell */
ddseq[MAXSTR], /* deuterium decoupling sequence */
shp_sl[MAXSTR],
shcreb[MAXSTR], /* reburp shape for center of t1 period */
shcgcob[MAXSTR], /* g3 inversion at 154 ppm (350 us) */
shcgcoib[MAXSTR], /* g3 time inversion at 154 ppm (350 us) */
shca180[MAXSTR], /* Ca 180 [D/sq(3)] during 15N CT */
shco180[MAXSTR], /* Co 180 [D/sq(15)] during 15N CT */
sel_flg[MAXSTR], /* active/passive purging of undesired
component */
fCT[MAXSTR], /* Flag for constant time C13 evolution */
fc180[MAXSTR],
cal_sphase[MAXSTR],
shared_CT[MAXSTR],
nietl_flg[MAXSTR];
int phase, phase2, ni2, icosel,
t1_counter, /* used for states tppi in t1 */
t2_counter; /* used for states tppi in t2 */
double tau1, /* t1 delay */
tau2, /* t2 delay */
taua, /* ~ 1/4JNH = 2.25 ms */
del1, /* time for C'-N to refocus set to 0.5*24.0 ms */
bigTN, /* nitrogen T period */
bigTC, /* carbon T period */
zeta, /* delay for transfer from ca to cb = 3.5 ms */
tsatpwr, /* low level 1H trans.power for presat */
sw1, /* sweep width in f1 */
sw2, /* sweep width in f2 */
tauf, /* 1/2J NH value */
pw_sl, /* selective pulse on water */
phase_sl, /* phase on water */
tpwrsl, /* power for pw_sl */
at,
d_cgcob, /* power level for g3 pulses at 154 ppm */
d_creb, /* power level for reburp 180 at center of t1 */
pwcgcob, /* g3 ~ 35o us 180 pulse */
pwcreb, /* reburp ~ 400us 180 pulse */
pwD, /* 2H 90 pulse, about 125 us */
pwDlvl, /* 2H 90 pulse, about 125 us */
pwca180, /* Ca 180 during N CT at d_ca180 */
pwco180, /* Co 180 during N CT at d_co180 */
d_ca180,
d_co180,
compC = getval("compC"), /* C-13 RF calibration parameters */
pwC = getval("pwC"),
pwClvl = getval("pwClvl"),
pwN,
pwNlvl,
sphase,
pw_sl1,
tpwrsl1,
gstab,
gt1,
gt2,
gt3,
gt4,
gt5,
gt6,
gt7,
gt8,
gt9,
gt11,
gt13,
gt14,
gzlvl1,
gzlvl2,
gzlvl3,
gzlvl4,
gzlvl5,
gzlvl6,
gzlvl7,
gzlvl8,
gzlvl9,
gzlvl11,
gzlvl13,
gzlvl14;
/* variables commented out are already defined by the system */
/* LOAD VARIABLES */
getstr("autocal",autocal);
getstr("fsat",fsat);
getstr("f1180",f1180);
getstr("f2180",f2180);
getstr("fscuba",fscuba);
getstr("ddseq",ddseq);
getstr("shp_sl",shp_sl);
getstr("sel_flg",sel_flg);
getstr("fCT",fCT);
getstr("fc180",fc180);
getstr("cal_sphase",cal_sphase);
getstr("shared_CT",shared_CT);
getstr("nietl_flg",nietl_flg);
taua = getval("taua");
del1 = getval("del1");
bigTN = getval("bigTN");
bigTC = getval("bigTC");
zeta = getval("zeta");
pwN = getval("pwN");
tpwr = getval("tpwr");
tsatpwr = getval("tsatpwr");
dpwr = getval("dpwr");
pwNlvl = getval("pwNlvl");
pwD = getval("pwD");
pwDlvl = getval("pwDlvl");
phase = (int) ( getval("phase") + 0.5);
phase2 = (int) ( getval("phase2") + 0.5);
sw1 = getval("sw1");
sw2 = getval("sw2");
ni2 = getval("ni2");
tauf = getval("tauf");
pw_sl = getval("pw_sl");
phase_sl = getval("phase_sl");
tpwrsl = getval("tpwrsl");
at = getval("at");
sphase = getval("sphase");
pw_sl1 = getval("pw_sl1");
tpwrsl1 = getval("tpwrsl1");
gstab = getval("gstab");
gt1 = getval("gt1");
if (getval("gt2") > 0) gt2=getval("gt2");
else gt2=gt1*0.1;
gt3 = getval("gt3");
gt4 = getval("gt4");
gt5 = getval("gt5");
gt6 = getval("gt6");
gt7 = getval("gt7");
gt8 = getval("gt8");
gt9 = getval("gt9");
gt11 = getval("gt11");
gt13 = getval("gt13");
gt14 = getval("gt14");
gzlvl1 = getval("gzlvl1");
gzlvl2 = getval("gzlvl2");
gzlvl3 = getval("gzlvl3");
gzlvl4 = getval("gzlvl4");
gzlvl5 = getval("gzlvl5");
gzlvl6 = getval("gzlvl6");
gzlvl7 = getval("gzlvl7");
gzlvl8 = getval("gzlvl8");
gzlvl9 = getval("gzlvl9");
gzlvl11 = getval("gzlvl11");
gzlvl13 = getval("gzlvl13");
gzlvl14 = getval("gzlvl14");
if(autocal[0]=='n')
{
getstr("shcgcob",shcgcob);
getstr("shcgcoib",shcgcoib);
getstr("shcreb",shcreb);
getstr("shca180",shca180);
getstr("shco180",shco180);
d_ca180 = getval("d_ca180");
d_co180 = getval("d_co180");
d_cgcob = getval("d_cgcob");
d_creb = getval("d_creb");
pwca180 = getval("pwca180");
pwco180 = getval("pwco180");
pwcgcob = getval("pwcgcob");
pwcreb = getval("pwcreb");
}
else
{
strcpy(shcgcob,"Pg3_107p");
strcpy(shcgcoib,"Pg3i_107p");
strcpy(shcreb,"Preb_on");
strcpy(shca180,"Phard_15p");
strcpy(shco180,"Phard_133p");
if (FIRST_FID)
{
cgcob = pbox(shcgcob, G3CGCOB, CAB180ps, dfrq, compC*pwC, pwClvl);
cgcoib = pbox(shcgcoib, G3CGCOBi, CAB180ps, dfrq, compC*pwC, pwClvl);
creb = pbox(shcreb, CREB180, CAB180ps, dfrq, compC*pwC, pwClvl);
ca180 = pbox(shca180, CA180, CA180ps, dfrq, compC*pwC, pwClvl);
co180 = pbox(shco180, CO180, CA180ps, dfrq, compC*pwC, pwClvl);
}
d_ca180 = ca180.pwr;
d_co180 = co180.pwr;
d_cgcob = cgcob.pwr;
d_creb = creb.pwr;
pwca180 = ca180.pw;
pwco180 = co180.pw;
pwcgcob = cgcob.pw;
pwcreb = creb.pw;
}
/* LOAD PHASE TABLE */
settable(t1,2,phi1);
settable(t2,4,phi2);
settable(t3,8,phi3);
settable(t4,1,phi4);
settable(t5,16,phi5);
settable(t6,8,phi6);
settable(t7,1,phi7);
settable(t8,16,rec);
/* CHECK VALIDITY OF PARAMETER RANGES */
if(shared_CT[A] == 'n')
if(bigTN - 0.5*(ni2 -1)/sw2 - POWER_DELAY < 0.2e-6)
{
text_error(" ni2 is too big\n");
text_error(" please set ni2 smaller or equal to %d\n",
(int) ((bigTN -POWER_DELAY)*sw2*2.0) +1 );
psg_abort(1);
}
if(fCT[A] == 'y')
if(bigTC - 0.5*(ni-1)/sw1 - WFG_STOP_DELAY - gt14 - 102.0e-6
- POWER_DELAY - 4.0e-6 - pwD - POWER_DELAY - PRG_START_DELAY
- POWER_DELAY - WFG_START_DELAY - 4.0e-6 - pwcgcob - WFG_STOP_DELAY
- POWER_DELAY - 4.0e-6 < 0.2e-6) {
text_error("ni is too big\n");
text_error(" please set ni smaller or equal to %d\n",
(int) ((bigTC - WFG_STOP_DELAY - gt14 - 102.0e-6
- POWER_DELAY - 4.0e-6 - pwD - POWER_DELAY - PRG_START_DELAY
- POWER_DELAY - WFG_START_DELAY - 4.0e-6 - pwcgcob - WFG_STOP_DELAY
- POWER_DELAY - 4.0e-6)*sw1*2.0) +1 );
psg_abort(1);
}
if((dm[A] == 'y' || dm[B] == 'y' || dm[C] == 'y'))
{
text_error("incorrect dec1 decoupler flags! ");
psg_abort(1);
}
if((dm2[A] == 'y' || dm2[B] == 'y' || dm2[C] == 'y'))
{
text_error("incorrect dec2 decoupler flags! Should be 'nnn' ");
psg_abort(1);
}
if( tsatpwr > 6 )
{
text_error("TSATPWR too large !!! ");
psg_abort(1);
}
if( dpwr > 46 )
{
text_error("don't fry the probe, DPWR too large! ");
psg_abort(1);
}
if( dpwr2 > 47 )
{
text_error("don't fry the probe, DPWR2 too large! ");
psg_abort(1);
}
if( pwClvl > 63 )
{
text_error("don't fry the probe, pwClvl too large! ");
psg_abort(1);
}
if( pwNlvl > 63 )
{
text_error("don't fry the probe, pwNlvl too large! ");
psg_abort(1);
}
if( pw > 200.0e-6 )
{
text_error("dont fry the probe, pw too high ! ");
psg_abort(1);
}
if( pwN > 200.0e-6 )
{
text_error("dont fry the probe, pwN too high ! ");
psg_abort(1);
}
if( pwC > 200.0e-6 )
{
text_error("dont fry the probe, pwC too high ! ");
psg_abort(1);
}
if( f1180[A] != 'n' && f2180[A] != 'n' ) {
text_error("flags may be set wrong: set f1180=n and f2180=n for 3d\n");
psg_abort(1);
}
if(d_ca180 > 58)
{
text_error("dont fry the probe, d_ca180 too high ! ");
psg_abort(1);
}
if(d_co180 > 58)
{
text_error("dont fry the probe, d_ca180 too high ! ");
psg_abort(1);
}
if( gt1 > 15e-3 || gt2 > 15e-3 || gt3 > 15e-3
|| gt4 > 15e-3 || gt5 > 15e-3 || gt6 > 15e-3
|| gt7 > 15e-3 || gt8 > 15e-3 || gt9 > 15e-3
|| gt11 > 15e-3 || gt13 > 15e-3
|| gt14 > 15e-3)
{
text_error("gti values must be < 15e-3\n");
psg_abort(1);
}
if(tpwrsl > 25) {
text_error("tpwrsl must be less than 25\n");
psg_abort(1);
}
if(tpwrsl1 > 25) {
text_error("tpwrsl1 must be less than 25\n");
psg_abort(1);
}
if( dpwr3 > 50) {
text_error("dpwr3 too high\n");
psg_abort(1);
}
if( del1 > 0.1 ) {
text_error("too long del1\n");
psg_abort(1);
}
if( zeta > 0.1 ) {
text_error("too long zeta\n");
psg_abort(1);
}
if( bigTN > 0.1) {
text_error("too long bigTN\n");
psg_abort(1);
}
if( bigTC > 0.1) {
text_error("too long bigTC\n");
psg_abort(1);
}
if( pw_sl > 10e-3) {
text_error("too long pw_sl\n");
psg_abort(1);
}
if( pw_sl1 > 10e-3) {
text_error("too long pw_sl1\n");
psg_abort(1);
}
if( at > 0.1 && dm2[D] == 'y') {
text_error("too long at with dec2\n");
psg_abort(1);
}
if(pwDlvl > 59) {
text_error("pwDlvl is too high; <= 59\n");
psg_abort(1);
}
if(d_creb > 62) {
text_error("d_creb is too high; <= 62\n");
psg_abort(1);
}
if(d_cgcob > 60) {
text_error("d_cgcob is too high; <=60\n");
psg_abort(1);
}
if(cal_sphase[A] == 'y') {
text_error("Use only to calibrate sphase\n");
text_error("Set zeta to 600 us, gt11=gt13=0, fCT=y, fc180=n\n");
}
if(nietl_flg[A] == 'y' && sel_flg[A] == 'y') {
text_error("Both nietl_flg and sel_flg cannot by y\n");
psg_abort(1);
}
if (fCT[A] == 'n' && fc180[A] =='y' && ni > 1.0) {
text_error("must set fc180='n' to allow Calfa/Cbeta evolution (ni>1)\n");
psg_abort(1);
}
/* Phase incrementation for hypercomplex 2D data */
/* changed from 1 to 3; spect. rev. not needed */
if (phase == 2) { tsadd(t2,3,4); tsadd(t3,3,4); }
if (shared_CT[A] == 'n')
{
if (phase2 == 2) { tsadd(t7,2,4); icosel = 1; }
else icosel = -1;
}
else
{
if (phase2 == 2) { tsadd(t7,2,4); icosel = -1; }
else icosel = 1;
}
if (nietl_flg[A] == 'y') icosel = -1*icosel;
/* Calculate modifications to phases for States-TPPI acquisition */
if( ix == 1) d2_init = d2 ;
t1_counter = (int) ( (d2-d2_init)*sw1 + 0.5 );
if(t1_counter % 2) {
tsadd(t2,2,4);
tsadd(t8,2,4);
}
if( ix == 1) d3_init = d3 ;
t2_counter = (int) ( (d3-d3_init)*sw2 + 0.5 );
if(t2_counter % 2) {
tsadd(t5,2,4);
tsadd(t8,2,4);
}
/* Set up f1180 tau1 = t1 */
tau1 = d2;
if(f1180[A] == 'y' && fCT[A] == 'y')
tau1 += ( 1.0 / (2.0*sw1) );
if(f1180[A] == 'y' && fCT[A] == 'n')
tau1 += (1.0 / (2.0*sw1) - 4.0/PI*pwC - POWER_DELAY
- 4.0e-6);
if(f1180[A] == 'n' && fCT[A] == 'n')
tau1 = (tau1 - 4.0/PI*pwC - POWER_DELAY
- 4.0e-6);
if(tau1 < 0.2e-6) tau1 = 4.0e-7;
tau1 = tau1/2.0;
/* Set up f2180 tau2 = t2 */
tau2 = d3;
if(f2180[A] == 'y') {
tau2 += ( 1.0 / (2.0*sw2) );
if(tau2 < 0.2e-6) tau2 = 0.2e-6;
}
tau2 = tau2/2.0;
/* BEGIN ACTUAL PULSE SEQUENCE */
status(A);
obspower(tsatpwr); /* Set transmitter power for 1H presaturation */
decpower(pwClvl); /* Set Dec1 power to high power */
dec2power(pwNlvl); /* Set Dec2 power for 15N hard pulses */
dec3power(pwDlvl); /* Set Dec3 for 2H hard pulses */
/* Presaturation Period */
if (fsat[0] == 'y')
{
delay(2.0e-5);
rgpulse(d1,zero,0.0,2.0e-6);
obspower(tpwr); /* Set transmitter power for hard 1H pulses */
delay(2.0e-5);
if (fscuba[0] == 'y')
{
delay(2.2e-2);
rgpulse(pw,zero,2.0e-6,0.0);
rgpulse(2*pw,one,2.0e-6,0.0);
rgpulse(pw,zero,2.0e-6,0.0);
delay(2.2e-2);
}
}
else
{
delay(d1);
}
obspower(tpwr); /* Set transmitter power for hard 1H pulses */
txphase(zero);
dec2phase(zero);
delay(1.0e-5);
/* Begin Pulses */
status(B);
rcvroff();
lk_hold();
delay(20.0e-6);
rgpulse(pw,zero,0.0,0.0); /* 90 deg 1H pulse */
delay(0.2e-6);
zgradpulse(gzlvl5,gt5);
delay(2.0e-6);
delay(taua - gt5 - 2.2e-6); /* taua <= 1/4JNH */
sim3pulse(2*pw,0.0,2*pwN,zero,zero,zero,0.0,0.0);
dec2phase(t1); decphase(zero);
delay(taua - gt5 - 200.2e-6);
delay(0.2e-6);
zgradpulse(gzlvl5,gt5);
delay(200.0e-6);
if (sel_flg[A] == 'y')
{
rgpulse(pw,one,4.0e-6,0.0);
initval(1.0,v2);
obsstepsize(phase_sl);
xmtrphase(v2);
/* shaped pulse */
obspower(tpwrsl);
shaped_pulse(shp_sl,pw_sl,two,2.0e-6,0.0);
xmtrphase(zero);
delay(2.0e-6);
obspower(tpwr);
/* shaped pulse */
initval(1.0,v6);
dec2stepsize(45.0);
dcplr2phase(v6);
delay(0.2e-6);
zgradpulse(gzlvl3,gt3);
delay(200.0e-6);
dec2rgpulse(pwN,t1,0.0,0.0);
dcplr2phase(zero);
delay(1.34e-3 - SAPS_DELAY);
rgpulse(pw,zero,0.0,0.0);
rgpulse(2.0*pw,one,2.0e-6,0.0);
rgpulse(pw,zero,2.0e-6,0.0);
decpower(d_ca180);
dec2phase(zero);
delay(del1 - 1.34e-3 - 4.0*pw - 4.0e-6
- POWER_DELAY + WFG_START_DELAY + pwca180 + WFG_STOP_DELAY);
}
else
{
rgpulse(pw,three,4.0e-6,0.0);
initval(1.0,v2);
obsstepsize(phase_sl);
xmtrphase(v2);
/* shaped pulse */
obspower(tpwrsl);
shaped_pulse(shp_sl,pw_sl,zero,2.0e-6,0.0);
xmtrphase(zero);
delay(2.0e-6);
obspower(tpwr);
/* shaped pulse */
delay(0.2e-6);
zgradpulse(gzlvl3,gt3);
delay(200.0e-6);
dec2rgpulse(pwN,t1,0.0,0.0);
dec2phase(zero);
decpower(d_ca180);
delay(del1 - POWER_DELAY + WFG_START_DELAY
+ pwca180 + WFG_STOP_DELAY);
}
decphase(zero);
dec2rgpulse(2*pwN,zero,0.0,0.0);
decshaped_pulse(shca180,pwca180,zero,0.0,0.0);
dec2phase(one);
delay(del1);
dec2rgpulse(pwN,one,0.0,0.0);
decpower(pwClvl);
decphase(t2);
delay(0.2e-6);
zgradpulse(gzlvl4,gt4);
delay(200.0e-6);
dec2phase(t5);
/* Turn on D decoupling using the third decoupler */
dec3phase(one);
dec3power(pwDlvl);
dec3rgpulse(pwD,one,4.0e-6,0.0);
dec3phase(zero);
dec3power(dpwr3);
dec3unblank();
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
/* Turn on D decoupling */
decrgpulse(pwC,t2,0.0,0.0);
delay(zeta
- PRG_STOP_DELAY - DELAY_BLANK - POWER_DELAY - 4.0e-6
- pwD
- gt11 - 102.0e-6 - POWER_DELAY - WFG_START_DELAY);
/* Turn off D decoupling */
setstatus(DEC3ch, FALSE, 'c', FALSE, dmf3);
dec3blank();
dec3phase(three);
dec3power(pwDlvl);
dec3rgpulse(pwD,three,4.0e-6,0.0);
/* Turn off D decoupling */
decphase(zero);
delay(2.0e-6);
zgradpulse(gzlvl11,gt11);
delay(100.0e-6);
if (cal_sphase[A] == 'y')
{
decpower(pwClvl);
decshaped_pulse("hard",2.0*pwC,zero,4.0e-6,4.0e-6);
}
else
{
initval(1.0,v3);
decstepsize(sphase);
dcplrphase(v3);
decpower(d_creb);
decshaped_pulse(shcreb,pwcreb,zero,4.0e-6,4.0e-6);
dcplrphase(zero);
}
delay(2.0e-6);
zgradpulse(gzlvl11,gt11);
delay(100.0e-6);
/* Turn on D decoupling using the third decoupler */
dec3phase(one);
dec3power(pwDlvl);
dec3rgpulse(pwD,one,4.0e-6,0.0);
dec3phase(zero);
dec3power(dpwr3);
dec3unblank();
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
/* Turn on D decoupling */
delay(zeta - WFG_STOP_DELAY - gt11 - 102.0e-6
- POWER_DELAY - 4.0e-6 - pwD - POWER_DELAY - PRG_START_DELAY
- DELAY_BLANK - POWER_DELAY - 4.0e-6);
decpower(pwClvl);
decrgpulse(pwC,t3,4.0e-6,0.0);
if (fCT[A] == 'y')
{
delay(tau1);
decpower(d_cgcob);
decshaped_pulse(shcgcob,pwcgcob,zero,4.0e-6,0.0);
delay(bigTC - POWER_DELAY - WFG_START_DELAY - 4.0e-6
- pwcgcob - WFG_STOP_DELAY
- 102.0e-6 - gt14
- PRG_STOP_DELAY - DELAY_BLANK
- POWER_DELAY - 4.0e-6 - pwD - POWER_DELAY - WFG_START_DELAY);
/* Turn off D decoupling */
setstatus(DEC3ch, FALSE, 'c', FALSE, dmf3);
dec3blank();
dec3phase(three);
dec3power(pwDlvl);
dec3rgpulse(pwD,three,4.0e-6,0.0);
/* Turn off D decoupling */
delay(2.0e-6);
zgradpulse(gzlvl14,gt14);
delay(100.0e-6);
initval(1.0,v4);
decstepsize(sphase);
dcplrphase(v4);
decpower(d_creb);
decshaped_pulse(shcreb,pwcreb,zero,4.0e-6,4.0e-6);
dcplrphase(zero);
delay(2.0e-6);
zgradpulse(gzlvl14,gt14);
delay(100.0e-6);
/* Turn on D decoupling using the third decoupler */
dec3phase(one);
dec3power(pwDlvl);
dec3rgpulse(pwD,one,4.0e-6,0.0);
dec3phase(zero);
dec3power(dpwr3);
dec3unblank();
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
/* Turn on D decoupling */
delay(bigTC - tau1 - WFG_STOP_DELAY - gt14
- 102.0e-6 - POWER_DELAY - 4.0e-6 - pwD - POWER_DELAY
- PRG_START_DELAY - POWER_DELAY - WFG_START_DELAY
- 4.0e-6 - pwcgcob - WFG_STOP_DELAY - POWER_DELAY
- 4.0e-6);
decpower(d_cgcob);
decshaped_pulse(shcgcoib,pwcgcob,zero,4.0e-6,0.0);
decphase(t4);
}
else if(fCT[A] == 'n' && fc180[A] == 'n')
{
delay(tau1);
delay(tau1);
}
else if(fCT[A] == 'n' && fc180[A] == 'y')
{
initval(1.0,v4);
decstepsize(sphase);
dcplrphase(v4);
decpower(d_creb);
decshaped_pulse(shcreb,pwcreb,zero,4.0e-6,0.0);
dcplrphase(zero);
}
decpower(pwClvl);
decrgpulse(pwC,t4,4.0e-6,0.0);
delay(zeta - POWER_DELAY - 4.0e-6
- pwD - PRG_STOP_DELAY - DELAY_BLANK
- gt13
- 102.0e-6 - POWER_DELAY - WFG_START_DELAY);
/* Turn off D decoupling */
setstatus(DEC3ch, FALSE, 'c', FALSE, dmf3);
dec3blank();
dec3power(pwDlvl);
dec3rgpulse(pwD,three,4.0e-6,0.0);
/* Turn off D decoupling */
delay(2.0e-6);
zgradpulse(gzlvl13,gt13);
delay(100.0e-6);
if (cal_sphase[A] == 'y')
{
decpower(pwClvl);
decshaped_pulse("hard",2.0*pwC,zero,4.0e-6,4.0e-6);
}
else
{
initval(1.0,v5);
decstepsize(sphase);
dcplrphase(v5);
decpower(d_creb);
decshaped_pulse(shcreb,pwcreb,zero,4.0e-6,4.0e-6);
dcplrphase(zero);
}
delay(2.0e-6);
zgradpulse(gzlvl13,gt13);
delay(100.0e-6);
/* Turn on D decoupling using the third decoupler */
dec3phase(one);
dec3power(pwDlvl);
dec3rgpulse(pwD,one,4.0e-6,0.0);
dec3phase(zero);
dec3power(dpwr3);
dec3unblank();
setstatus(DEC3ch, TRUE, 'w', FALSE, dmf3);
/* Turn on D decoupling */
delay(zeta - WFG_STOP_DELAY - gt13 - 102.0e-6
- POWER_DELAY - 4.0e-6 - pwD - POWER_DELAY
- PRG_START_DELAY - DELAY_BLANK
- POWER_DELAY - 4.0e-6);
decpower(pwClvl);
decrgpulse(pwC,zero,4.0e-6,0.0);
/* Turn off D decoupling */
setstatus(DEC3ch, FALSE, 'c', FALSE, dmf3);
dec3blank();
dec3phase(three);
dec3power(pwDlvl);
dec3rgpulse(pwD,three,4.0e-6,0.0);
/* Turn off D decoupling */
delay(0.2e-6);
zgradpulse(gzlvl9,gt9);
delay(200.0e-6);
if (shared_CT[A] == 'n')
{
dec2rgpulse(pwN,t5,2.0e-6,0.0);
decpower(d_ca180);
dec2phase(t6);
delay(bigTN - tau2 - POWER_DELAY);
dec2rgpulse(2*pwN,t6,0.0,0.0);
decshaped_pulse(shca180,pwca180,zero,0.0,0.0);
dec2phase(t7);
delay(bigTN - WFG_START_DELAY - pwca180 - WFG_STOP_DELAY
- gt1 - 2.0*GRADIENT_DELAY - 500.2e-6
- POWER_DELAY - 4.0e-6 - WFG_START_DELAY
- pwco180 - WFG_STOP_DELAY);
delay(0.2e-6);
zgradpulse(gzlvl1,gt1);
delay(500.0e-6);
decpower(d_co180);
decshaped_pulse(shco180,pwco180,zero,4.0e-6,0.0);
delay(tau2);
sim3pulse(pw,0.0,pwN,zero,zero,t7,0.0,0.0);
}
else if (shared_CT[A] == 'y')
{
dec2rgpulse(pwN,t5,2.0e-6,0.0);
decpower(d_co180);
dec2phase(t6);
if (bigTN - tau2 >= 0.2e-6)
{
delay(tau2);
decshaped_pulse(shco180,pwco180,zero,4.0e-6,0.0);
decpower(d_ca180);
delay(0.2e-6);
zgradpulse(gzlvl1,gt1);
delay(500.0e-6);
delay(bigTN - 4.0e-6 - WFG_START_DELAY - pwco180 - WFG_STOP_DELAY
- POWER_DELAY - gt1 - 500.2e-6 - 2.0*GRADIENT_DELAY
- WFG_START_DELAY - pwca180 - WFG_STOP_DELAY);
decshaped_pulse(shca180,pwca180,zero,0.0,0.0);
dec2rgpulse(2*pwN,t6,0.0,0.0);
delay(bigTN - tau2);
}
else
{
delay(tau2);
decshaped_pulse(shco180,pwco180,zero,4.0e-6,0.0);
delay(0.2e-6);
zgradpulse(gzlvl1,gt1);
delay(500.0e-6);
decpower(d_ca180);
delay(bigTN - 4.0e-6 - WFG_START_DELAY - pwco180
- WFG_STOP_DELAY - gt1 - 500.2e-6 - 2.0*GRADIENT_DELAY
- POWER_DELAY - WFG_START_DELAY - pwca180 - WFG_STOP_DELAY);
decshaped_pulse(shca180,pwca180,zero,0.0,0.0);
delay(tau2 - bigTN);
dec2rgpulse(2.0*pwN,t6,0.0,0.0);
}
sim3pulse(pw,0.0,pwN,zero,zero,t7,0.0,0.0);
}
/* end of shared_CT */
if (nietl_flg[A] == 'n')
{
decpower(pwClvl);
decrgpulse(pwC,zero,4.0e-6,0.0);
delay(0.2e-6);
zgradpulse(gzlvl6,gt6);
delay(2.0e-6);
dec2phase(zero);
delay(tauf - POWER_DELAY - 4.0e-6
- pwC - gt6 - 2.2e-6);
sim3pulse(2*pw,0.0,2*pwN,zero,zero,zero,0.0,0.0);
txphase(one);
dec2phase(one);
delay(tauf - gt6 - 200.2e-6);
delay(0.2e-6);
zgradpulse(gzlvl6,gt6);
delay(200.0e-6);
sim3pulse(pw,0.0,pwN,one,zero,one,0.0,0.0);
delay(0.2e-6);
zgradpulse(gzlvl7,gt7);
delay(2.0e-6);
txphase(zero);
dec2phase(zero);
delay(tauf - gt7 - 2.2e-6);
sim3pulse(2*pw,0.0,2*pwN,zero,zero,zero,0.0,0.0);
delay(tauf - gt7 - 200.2e-6);
delay(0.2e-6);
zgradpulse(gzlvl7,gt7);
delay(200.0e-6);
sim3pulse(pw,0.0e-6,pwN,zero,zero,zero,0.0,0.0);
}
else
{ /* nietl_flg == y */
/* shaped pulse */
obspower(tpwrsl1);
shaped_pulse(shp_sl,pw_sl1,zero,2.0e-6,0.0);
delay(2.0e-6);
obspower(tpwr);
/* shaped pulse */
decpower(pwClvl);
decrgpulse(pwC,zero,4.0e-6,0.0);
delay(0.2e-6);
zgradpulse(gzlvl6,gt6);
delay(2.0e-6);
dec2phase(zero);
delay(tauf
- POWER_DELAY - 2.0e-6 - WFG_START_DELAY
- pw_sl1 - WFG_STOP_DELAY - 2.0e-6 - POWER_DELAY
- POWER_DELAY - 4.0e-6
- pwC - gt6 - 2.2e-6);
sim3pulse(2*pw,0.0,2*pwN,zero,zero,zero,0.0,0.0);
txphase(one);
dec2phase(zero);
delay(tauf - gt6 - 200.2e-6);
delay(0.2e-6);
zgradpulse(gzlvl6,gt6);
delay(200.0e-6);
sim3pulse(pw,0.0,pwN,one,zero,zero,0.0,0.0);
delay(0.2e-6);
zgradpulse(gzlvl7,gt7);
delay(2.0e-6);
txphase(zero);
dec2phase(zero);
delay(tauf - gt7 - 2.2e-6);
sim3pulse(2*pw,0.0,2*pwN,zero,zero,zero,0.0,0.0);
txphase(one);
dec2phase(one);
delay(tauf - gt7 - 200.2e-6);
delay(0.2e-6);
zgradpulse(gzlvl7,gt7);
delay(200.0e-6);
sim3pulse(pw,0.0e-6,pwN,one,zero,one,0.0,0.0);
txphase(zero);
} /* end of nietl_flg == y */
delay(gt2 +gstab -0.5*(pwN-pw) -2.0*pw/PI);
rgpulse(2*pw,zero,0.0,0.0);
delay(2.0e-6);
zgradpulse(icosel*gzlvl2,gt2);
decpower(dpwr); /* NO 13C decoupling */
dec2power(dpwr2); /* NO 15N decoupling */
delay(gstab -2.0e-6 -2.0*GRADIENT_DELAY -2.0*POWER_DELAY);
lk_sample();
/* BEGIN ACQUISITION */
status(C);
setreceiver(t8);
}