void TBlockingSpiDmaJob::Run()
{
TaskId = TScheduler::GetCurrentTaskId();
CurrentJob = this;
const uint32_t spi = FLASH_SPI_CHANNEL;
const uint32_t dma = DMA1;
assert(SPI_SR(spi) & SPI_SR_TXE);
assert(~SPI_SR(spi) & SPI_SR_BSY);
assert(!(SPI_SR(spi) & SPI_SR_RXNE));
{
const uint32_t channel = FLASH_DMA_TX_CHANNEL;
dma_channel_reset(dma, channel);
dma_set_peripheral_address(dma, channel, reinterpret_cast<uint32_t>(&SPI_DR(spi)));
dma_set_memory_address(dma, channel, reinterpret_cast<uint32_t>(Out));
dma_set_number_of_data(dma, channel, Len);
dma_set_read_from_memory(dma, channel);
dma_enable_memory_increment_mode(dma, channel);
dma_set_peripheral_size(dma, channel, DMA_CCR_PSIZE_8BIT);
dma_set_memory_size(dma, channel, DMA_CCR_MSIZE_8BIT);
dma_set_priority(dma, channel, DMA_CCR_PL_LOW);
// dma_enable_transfer_complete_interrupt(dma, channel);
dma_enable_channel(dma, channel);
}
{
const uint32_t channel = FLASH_DMA_RX_CHANNEL;
dma_channel_reset(dma, channel);
dma_set_peripheral_address(dma, channel, reinterpret_cast<uint32_t>(&SPI_DR(spi)));
dma_set_number_of_data(dma, channel, Len);
if (In != 0) {
dma_set_memory_address(dma, channel, reinterpret_cast<uint32_t>(In));
dma_enable_memory_increment_mode(dma, channel);
}
else {
dma_set_memory_address(dma, channel, reinterpret_cast<uint32_t>(&DummyPosition));
}
dma_set_peripheral_size(dma, channel, DMA_CCR_PSIZE_8BIT);
dma_set_memory_size(dma, channel, DMA_CCR_MSIZE_8BIT);
dma_set_priority(dma, channel, DMA_CCR_PL_LOW);
dma_enable_transfer_complete_interrupt(dma, channel);
dma_enable_channel(dma, channel);
}
// Kick off the transfer
spi_enable_rx_dma(spi);
spi_enable_tx_dma(spi);
// Wait for completion
TScheduler::BlockUntil(&Finished);
}
void hal_uart_dma_receive_block(uint8_t *data, uint16_t size){
// hal_uart_manual_rts_clear();
gpio_clear(GPIOB, GPIO_DEBUG_1);
/*
* USART3_RX is on DMA_CHANNEL3
*/
// printf("hal_uart_dma_receive_block req size %u\n", size);
/* Reset DMA channel*/
dma_channel_reset(DMA1, DMA_CHANNEL3);
dma_set_peripheral_address(DMA1, DMA_CHANNEL3, (uint32_t)&USART3_DR);
dma_set_memory_address(DMA1, DMA_CHANNEL3, (uint32_t)data);
dma_set_number_of_data(DMA1, DMA_CHANNEL3, size);
dma_set_read_from_peripheral(DMA1, DMA_CHANNEL3);
dma_enable_memory_increment_mode(DMA1, DMA_CHANNEL3);
dma_set_peripheral_size(DMA1, DMA_CHANNEL3, DMA_CCR_PSIZE_8BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL3, DMA_CCR_MSIZE_8BIT);
dma_set_priority(DMA1, DMA_CHANNEL3, DMA_CCR_PL_HIGH);
dma_enable_transfer_complete_interrupt(DMA1, DMA_CHANNEL3);
dma_enable_channel(DMA1, DMA_CHANNEL3);
usart_enable_rx_dma(USART3);
}
void mew_bluetooth_transmit(uint8_t* data, uint16_t size, uint8_t sync_mode) {
mew_check_dma_memory((void*)data, "mew_bluetooth_transmit");
mew_wait_for_state(&_mew_dma_tx_state, 0);
_mew_dma_tx_state = 1;
dma_stream_reset(MEW_BLUETOOTH_DMA, MEW_BLUETOOTH_DMA_STREAM_TX);
dma_set_transfer_mode(MEW_BLUETOOTH_DMA, MEW_BLUETOOTH_DMA_STREAM_TX, DMA_SxCR_DIR_MEM_TO_PERIPHERAL);
dma_set_priority(MEW_BLUETOOTH_DMA, MEW_BLUETOOTH_DMA_STREAM_TX, DMA_SxCR_PL_HIGH);
dma_set_memory_size(MEW_BLUETOOTH_DMA, MEW_BLUETOOTH_DMA_STREAM_TX, DMA_SxCR_MSIZE_8BIT);
dma_set_peripheral_size(MEW_BLUETOOTH_DMA, MEW_BLUETOOTH_DMA_STREAM_TX, DMA_SxCR_PSIZE_8BIT);
dma_enable_memory_increment_mode(MEW_BLUETOOTH_DMA, MEW_BLUETOOTH_DMA_STREAM_TX);
dma_set_peripheral_address(MEW_BLUETOOTH_DMA, MEW_BLUETOOTH_DMA_STREAM_TX, (uint32_t) &MEW_BLUETOOTH_DMA_DR);
dma_channel_select(MEW_BLUETOOTH_DMA, MEW_BLUETOOTH_DMA_STREAM_TX, MEW_BLUETOOTH_DMA_CHANNEL_TX);
dma_set_memory_address(MEW_BLUETOOTH_DMA, MEW_BLUETOOTH_DMA_STREAM_TX, (uint32_t) data);
dma_set_number_of_data(MEW_BLUETOOTH_DMA, MEW_BLUETOOTH_DMA_STREAM_TX, size);
dma_disable_fifo_error_interrupt(MEW_BLUETOOTH_DMA, MEW_BLUETOOTH_DMA_STREAM_TX);
dma_disable_half_transfer_interrupt(MEW_BLUETOOTH_DMA, MEW_BLUETOOTH_DMA_STREAM_TX);
dma_enable_transfer_complete_interrupt(MEW_BLUETOOTH_DMA, MEW_BLUETOOTH_DMA_STREAM_TX);
dma_enable_transfer_error_interrupt(MEW_BLUETOOTH_DMA, MEW_BLUETOOTH_DMA_STREAM_TX);
dma_enable_transfer_complete_interrupt(MEW_BLUETOOTH_DMA, MEW_BLUETOOTH_DMA_STREAM_TX);
__mew_bluetooth_clear_buf();
dma_enable_stream(MEW_BLUETOOTH_DMA, MEW_BLUETOOTH_DMA_STREAM_TX);
if (sync_mode == 1) {
mew_wait_for_state(&_mew_dma_tx_state, 0);
}
}
void baro_init()
{
gpio_set_mode(GPIOB, GPIO_MODE_INPUT, GPIO_CNF_INPUT_PULL_UPDOWN, GPIO14);
gpio_set_mode(GPIOB, GPIO_MODE_OUTPUT_50_MHZ,
GPIO_CNF_OUTPUT_ALTFN_PUSHPULL, GPIO13 | GPIO15);
gpio_set_mode(GPIOB, GPIO_MODE_OUTPUT_50_MHZ,
GPIO_CNF_OUTPUT_PUSHPULL, GPIO12);
deselect_slave();
spi_init_master(SPI2, SPI_CR1_BAUDRATE_FPCLK_DIV_8, SPI_CR1_CPOL,
SPI_CR1_CPHA, SPI_CR1_DFF_8BIT, SPI_CR1_MSBFIRST);
spi_enable_ss_output(SPI2);
spi_enable(SPI2);
dma_set_peripheral_address(DMA1, DMA_CHANNEL3, SPI2_DR);
dma_set_read_from_memory(DMA1, DMA_CHANNEL3);
dma_enable_memory_increment_mode(DMA1, DMA_CHANNEL3);
dma_set_peripheral_size(DMA1, DMA_CHANNEL3, DMA_CCR_PSIZE_8BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL3, DMA_CCR_MSIZE_8BIT);
dma_set_priority(DMA1, DMA_CHANNEL3, DMA_CCR_PL_HIGH);
dma_set_peripheral_address(DMA1, DMA_CHANNEL4, SPI2_DR);
dma_set_read_from_peripheral(DMA1, DMA_CHANNEL4);
dma_enable_memory_increment_mode(DMA1, DMA_CHANNEL4);
dma_set_peripheral_size(DMA1, DMA_CHANNEL4, DMA_CCR_PSIZE_8BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL4, DMA_CCR_MSIZE_8BIT);
dma_set_priority(DMA1, DMA_CHANNEL4, DMA_CCR_PL_VERY_HIGH);
dma_enable_transfer_complete_interrupt(DMA1, DMA_CHANNEL4);
timer_reset(TIM4);
timer_enable_irq(TIM4, TIM_DIER_UIE);
timer_set_mode(TIM4, TIM_CR1_CKD_CK_INT,
TIM_CR1_CMS_EDGE, TIM_CR1_DIR_UP);
/* 3200 / 16 = 200 Hz */
timer_set_prescaler(TIM4, 32);
timer_set_period(TIM4, 5625);
nvic_set_priority(NVIC_TIM4_IRQ, 16 * 2);
nvic_set_priority(NVIC_DMA1_CHANNEL4_IRQ, 16 * 2);
nvic_enable_irq(NVIC_TIM4_IRQ);
nvic_enable_irq(NVIC_DMA1_CHANNEL4_IRQ);
read_calibration_data();
}
/* SPI transmit completed with DMA */
void dma1_channel3_isr(void)
{
gpio_set(GPIOB,GPIO1);
if ((DMA1_ISR &DMA_ISR_TCIF3) != 0) {
DMA1_IFCR |= DMA_IFCR_CTCIF3;
}
dma_disable_transfer_complete_interrupt(DMA1, DMA_CHANNEL3);
spi_disable_tx_dma(SPI1);
dma_disable_channel(DMA1, DMA_CHANNEL3);
/* If tx_len < rx_len, create a dummy transfer to clock in the remaining
* rx data
*/
if (rx_buf_remainder > 0) {
dma_channel_reset(DMA1, DMA_CHANNEL3);
dma_set_peripheral_address(DMA1, DMA_CHANNEL3, (uint32_t)&SPI1_DR);
dma_set_memory_address(DMA1, DMA_CHANNEL3, (uint32_t)(&dummy_tx_buf)); // Change here
dma_set_number_of_data(DMA1, DMA_CHANNEL3, rx_buf_remainder); // Change here
dma_set_read_from_memory(DMA1, DMA_CHANNEL3);
dma_disable_memory_increment_mode(DMA1, DMA_CHANNEL3); // Change here
#if USE_16BIT_TRANSFERS
dma_set_peripheral_size(DMA1, DMA_CHANNEL3, DMA_CCR_PSIZE_16BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL3, DMA_CCR_MSIZE_16BIT);
#else
dma_set_peripheral_size(DMA1, DMA_CHANNEL3, DMA_CCR_PSIZE_8BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL3, DMA_CCR_MSIZE_8BIT);
#endif
dma_set_priority(DMA1, DMA_CHANNEL3, DMA_CCR_PL_HIGH);
rx_buf_remainder = 0; // Clear the buffer remainder to disable this section later
dma_enable_transfer_complete_interrupt(DMA1, DMA_CHANNEL3);
dma_enable_channel(DMA1, DMA_CHANNEL3);
spi_enable_tx_dma(SPI1);
} else {
/* Increment the status to indicate one of the transfers is complete */
transceive_status++;
}
gpio_clear(GPIOB,GPIO1);
}
/* Receive data using DMA. */
void rx_spi(void *data, uint16_t size){
if(DmaCleanupNeeded)cleanup_dma_spi();
/* This byte is sent continuously when rx_spi() receives data. */
static const uint8_t RxSpiDummyByte = 0x00;
spi_enable_rx_dma(SPI3);
dma_channel_reset(DMA1, DMA_CHANNEL2);
dma_disable_channel(DMA1, DMA_CHANNEL2);
dma_set_peripheral_address(DMA1, DMA_CHANNEL2, (uint32_t) &(SPI_DR(SPI3)));
dma_set_memory_address(DMA1, DMA_CHANNEL2, (uint32_t) data);
dma_set_number_of_data(DMA1, DMA_CHANNEL2, size);
dma_set_priority(DMA1, DMA_CHANNEL2, DMA_CCR_PL_HIGH);
dma_set_memory_size(DMA1, DMA_CHANNEL2, DMA_CCR_MSIZE_8BIT);
dma_set_peripheral_size(DMA1, DMA_CHANNEL2, DMA_CCR_PSIZE_8BIT);
dma_enable_memory_increment_mode(DMA1, DMA_CHANNEL2);
dma_disable_peripheral_increment_mode(DMA1, DMA_CHANNEL2);
dma_set_read_from_peripheral(DMA1, DMA_CHANNEL2);
dma_enable_channel(DMA1, DMA_CHANNEL2);
/* The SPI peripheral is driven by transmitted bytes, so dummy bytes
* must be sent in order to receive data. This is accomplished with DMA
* by simply not incrementing the memory address. */
dma_channel_reset(DMA1, DMA_CHANNEL3);
dma_disable_channel(DMA1, DMA_CHANNEL3);
dma_set_peripheral_address(DMA1, DMA_CHANNEL3, (uint32_t) &(SPI_DR(SPI3)));
dma_set_memory_address(DMA1, DMA_CHANNEL3, (uint32_t) &RxSpiDummyByte);
dma_set_number_of_data(DMA1, DMA_CHANNEL3, size);
dma_set_priority(DMA1, DMA_CHANNEL3, DMA_CCR_PL_HIGH);
dma_set_memory_size(DMA1, DMA_CHANNEL3, DMA_CCR_MSIZE_8BIT);
dma_set_peripheral_size(DMA1, DMA_CHANNEL3, DMA_CCR_PSIZE_8BIT);
dma_disable_memory_increment_mode(DMA1, DMA_CHANNEL3);
dma_disable_peripheral_increment_mode(DMA1, DMA_CHANNEL3);
dma_set_read_from_memory(DMA1, DMA_CHANNEL3);
dma_enable_channel(DMA1, DMA_CHANNEL3);
spi_enable_tx_dma(SPI3);
spi_enable(SPI3);
DmaCleanupNeeded = true;
}
/******************************************************************************
*
* Helpers for SPI transactions with DMA
*
*****************************************************************************/
static void spi_configure_dma(uint32_t dma, uint8_t chan, uint32_t periph_addr, uint32_t buf_addr,
uint16_t len, enum SPIDataSizeSelect dss, bool_t increment)
{
dma_channel_reset(dma, chan);
dma_set_peripheral_address(dma, chan, periph_addr);
dma_set_memory_address(dma, chan, buf_addr);
dma_set_number_of_data(dma, chan, len);
/* Set the dma transfer size based on SPI transaction DSS */
if (dss == SPIDss8bit) {
dma_set_peripheral_size(dma, chan, DMA_CCR_PSIZE_8BIT);
dma_set_memory_size(dma, chan, DMA_CCR_MSIZE_8BIT);
} else {
dma_set_peripheral_size(dma, chan, DMA_CCR_PSIZE_16BIT);
dma_set_memory_size(dma, chan, DMA_CCR_MSIZE_16BIT);
}
if (increment)
dma_enable_memory_increment_mode(dma, chan);
else
dma_disable_memory_increment_mode(dma, chan);
}
/* Simultaneously transmit and receive data using DMA. */
void rxtx_spi(void *rxdata, const void *txdata, uint16_t size){
if(DmaCleanupNeeded)cleanup_dma_spi();
spi_enable_rx_dma(SPI3);
dma_channel_reset(DMA1, DMA_CHANNEL2);
dma_disable_channel(DMA1, DMA_CHANNEL2);
dma_set_peripheral_address(DMA1, DMA_CHANNEL2, (uint32_t) &(SPI_DR(SPI3)));
dma_set_memory_address(DMA1, DMA_CHANNEL2, (uint32_t) rxdata);
dma_set_number_of_data(DMA1, DMA_CHANNEL2, size);
dma_set_priority(DMA1, DMA_CHANNEL2, DMA_CCR_PL_HIGH);
dma_set_memory_size(DMA1, DMA_CHANNEL2, DMA_CCR_MSIZE_8BIT);
dma_set_peripheral_size(DMA1, DMA_CHANNEL2, DMA_CCR_PSIZE_8BIT);
dma_enable_memory_increment_mode(DMA1, DMA_CHANNEL2);
dma_disable_peripheral_increment_mode(DMA1, DMA_CHANNEL2);
dma_set_read_from_peripheral(DMA1, DMA_CHANNEL2);
dma_enable_channel(DMA1, DMA_CHANNEL2);
dma_channel_reset(DMA1, DMA_CHANNEL3);
dma_disable_channel(DMA1, DMA_CHANNEL3);
dma_set_peripheral_address(DMA1, DMA_CHANNEL3, (uint32_t) &(SPI_DR(SPI3)));
dma_set_memory_address(DMA1, DMA_CHANNEL3, (uint32_t) txdata);
dma_set_number_of_data(DMA1, DMA_CHANNEL3, size);
dma_set_priority(DMA1, DMA_CHANNEL3, DMA_CCR_PL_HIGH);
dma_set_memory_size(DMA1, DMA_CHANNEL3, DMA_CCR_MSIZE_8BIT);
dma_set_peripheral_size(DMA1, DMA_CHANNEL3, DMA_CCR_PSIZE_8BIT);
dma_enable_memory_increment_mode(DMA1, DMA_CHANNEL3);
dma_disable_peripheral_increment_mode(DMA1, DMA_CHANNEL3);
dma_set_read_from_memory(DMA1, DMA_CHANNEL3);
dma_enable_channel(DMA1, DMA_CHANNEL3);
spi_enable_tx_dma(SPI3);
spi_enable(SPI3);
DmaCleanupNeeded = true;
}
void usart_tx(char *buf, unsigned short len) {
usart_enable_tx_dma(USART1);
dma_stream_reset(DMA2, DMA_STREAM7);
dma_set_priority(DMA2, DMA_STREAM7, DMA_SxCR_PL_LOW);
dma_set_memory_size(DMA2, DMA_STREAM7, DMA_SxCR_MSIZE_8BIT);
dma_set_peripheral_size(DMA2, DMA_STREAM7, DMA_SxCR_PSIZE_8BIT);
dma_enable_memory_increment_mode(DMA2, DMA_STREAM7);
dma_set_transfer_mode(DMA2, DMA_STREAM7, DMA_SxCR_DIR_MEM_TO_PERIPHERAL);
dma_set_peripheral_address(DMA2, DMA_STREAM7, (uint32_t) &USART1_DR);
dma_set_memory_address(DMA2, DMA_STREAM7, (uint32_t) buf);
dma_set_number_of_data(DMA2, DMA_STREAM7, len);
dma_enable_transfer_complete_interrupt(DMA2, DMA_STREAM7);
dma_channel_select(DMA2, DMA_STREAM7, DMA_SxCR_CHSEL_4);
dma_enable_stream(DMA2, DMA_STREAM7);
}
static void __dma_tx_setup(const uint8_t *txb, const uint8_t *_txb, size_t n)
{
const uint8_t *bufptr;
/* Reset stream in case any op is going on */
dma_stream_reset(DMA1, DMA_STREAM4);
dma_set_transfer_mode(DMA1, DMA_STREAM4, DMA_SxCR_DIR_MEM_TO_PERIPHERAL);
dma_set_priority(DMA1, DMA_STREAM4, DMA_SxCR_PL_HIGH);
dma_set_memory_size(DMA1, DMA_STREAM4, DMA_SxCR_MSIZE_8BIT);
dma_set_peripheral_size(DMA1, DMA_STREAM4, DMA_SxCR_PSIZE_8BIT);
if (txb) {
dma_enable_memory_increment_mode(DMA1, DMA_STREAM4);
bufptr = txb;
} else {
bufptr = _txb;
}
__spi_dma_setup(DMA_STREAM4, (uint32_t)bufptr, n);
}
void dma_transmit_setup(void)
{
dma_channel_reset(DMA1, DMA_CHANNEL4);
nvic_enable_irq(NVIC_DMA1_CHANNEL4_5_IRQ);
dma_set_peripheral_address(DMA1, DMA_CHANNEL4, (uint32_t) &USART2_TDR);
dma_set_read_from_memory(DMA1, DMA_CHANNEL4);
dma_set_peripheral_size(DMA1, DMA_CHANNEL4, DMA_CCR_PSIZE_8BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL4, DMA_CCR_MSIZE_8BIT);
dma_set_priority(DMA1, DMA_CHANNEL4, DMA_CCR_PL_VERY_HIGH);
dma_disable_peripheral_increment_mode(DMA1, DMA_CHANNEL4);
dma_enable_memory_increment_mode(DMA1, DMA_CHANNEL4);
dma_disable_transfer_error_interrupt(DMA1, DMA_CHANNEL4);
dma_disable_half_transfer_interrupt(DMA1, DMA_CHANNEL4);
dma_enable_transfer_complete_interrupt(DMA1, DMA_CHANNEL4);
}
/*--------------------------------------------------------------------*/
void dma_setup(void)
{
/* DAC channel 1 shares DMA controller 2 Channel 3. */
/* Enable DMA2 clock and IRQ */
rcc_peripheral_enable_clock(&RCC_AHBENR, RCC_AHBENR_DMA2EN);
nvic_enable_irq(NVIC_DMA2_CHANNEL3_IRQ);
dma_channel_reset(DMA2,DMA_CHANNEL3);
dma_set_priority(DMA2,DMA_CHANNEL3,DMA_CCR_PL_LOW);
dma_set_memory_size(DMA2,DMA_CHANNEL3,DMA_CCR_MSIZE_8BIT);
dma_set_peripheral_size(DMA2,DMA_CHANNEL3,DMA_CCR_PSIZE_8BIT);
dma_enable_memory_increment_mode(DMA2,DMA_CHANNEL3);
dma_enable_circular_mode(DMA2,DMA_CHANNEL3);
dma_set_read_from_memory(DMA2,DMA_CHANNEL3);
/* The register to target is the DAC1 8-bit right justified data register */
dma_set_peripheral_address(DMA2,DMA_CHANNEL3,(uint32_t) &DAC_DHR8R1);
/* The array v[] is filled with the waveform data to be output */
dma_set_memory_address(DMA2,DMA_CHANNEL3,(uint32_t) v);
dma_set_number_of_data(DMA2,DMA_CHANNEL3,256);
dma_enable_transfer_complete_interrupt(DMA2, DMA_CHANNEL3);
dma_enable_channel(DMA2,DMA_CHANNEL3);
}
static void __dma_rx_setup(uint8_t *rxb, uint8_t *_rxb, size_t n)
{
uint8_t *bufptr;
/* Reset stream in case any op is going on */
dma_stream_reset(DMA1, DMA_STREAM3);
dma_set_transfer_mode(DMA1, DMA_STREAM3, DMA_SxCR_DIR_PERIPHERAL_TO_MEM);
dma_set_priority(DMA1, DMA_STREAM3, DMA_SxCR_PL_VERY_HIGH);
dma_set_memory_size(DMA1, DMA_STREAM3, DMA_SxCR_MSIZE_8BIT);
dma_set_peripheral_size(DMA1, DMA_STREAM3, DMA_SxCR_PSIZE_8BIT);
if (rxb) {
dma_enable_memory_increment_mode(DMA1, DMA_STREAM3);
bufptr = rxb;
} else {
bufptr = _rxb;
}
__spi_dma_setup(DMA_STREAM3, (uint32_t)bufptr, n);
}
u8 UART_Send(u8 *data, u16 len) {
if (busy) return 1;
busy = 1;
dma_channel_reset(_USART_DMA, _USART_DMA_CHANNEL);
dma_set_peripheral_address(_USART_DMA, _USART_DMA_CHANNEL,(u32) &_USART_DR); /* send data to the USART data register */
dma_set_memory_address(_USART_DMA, _USART_DMA_CHANNEL, (u32) data);
dma_set_number_of_data(_USART_DMA, _USART_DMA_CHANNEL, len);
dma_set_read_from_memory(_USART_DMA, _USART_DMA_CHANNEL); /* direction is from memory to usart */
dma_enable_memory_increment_mode(_USART_DMA, _USART_DMA_CHANNEL); /* memory pointer increments, peripheral no */
dma_set_peripheral_size(_USART_DMA, _USART_DMA_CHANNEL, DMA_CCR_PSIZE_8BIT); /* USART_DR is 8bit wide in this mode */
dma_set_memory_size(_USART_DMA, _USART_DMA_CHANNEL, DMA_CCR_MSIZE_8BIT); /* destination memory is also 8 bit wide */
dma_set_priority(_USART_DMA, _USART_DMA_CHANNEL, DMA_CCR_PL_LOW);
dma_enable_transfer_complete_interrupt(_USART_DMA, _USART_DMA_CHANNEL);
dma_enable_channel(_USART_DMA, _USART_DMA_CHANNEL); /* dma ready to go */
usart_enable_tx_dma(_USART);
return 0;
}
void hal_uart_dma_send_block(const uint8_t *data, uint16_t size){
// printf("hal_uart_dma_send_block size %u\n", size);
/*
* USART3_TX Using DMA_CHANNEL2
*/
/* Reset DMA channel*/
dma_channel_reset(DMA1, DMA_CHANNEL2);
dma_set_peripheral_address(DMA1, DMA_CHANNEL2, (uint32_t)&USART3_DR);
dma_set_memory_address(DMA1, DMA_CHANNEL2, (uint32_t)data);
dma_set_number_of_data(DMA1, DMA_CHANNEL2, size);
dma_set_read_from_memory(DMA1, DMA_CHANNEL2);
dma_enable_memory_increment_mode(DMA1, DMA_CHANNEL2);
dma_set_peripheral_size(DMA1, DMA_CHANNEL2, DMA_CCR_PSIZE_8BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL2, DMA_CCR_MSIZE_8BIT);
dma_set_priority(DMA1, DMA_CHANNEL2, DMA_CCR_PL_VERY_HIGH);
dma_enable_transfer_complete_interrupt(DMA1, DMA_CHANNEL2);
dma_enable_channel(DMA1, DMA_CHANNEL2);
usart_enable_tx_dma(USART3);
}
u8 UART_Send(u8 *data, u16 len) {
if (busy) return 1;
busy = 1;
DMA_stream_reset(USART_DMA);
dma_set_peripheral_address(USART_DMA.dma, USART_DMA.stream, (u32) &USART_DR(UART_CFG.uart)); /* send data to the USART data register */
dma_set_memory_address(USART_DMA.dma, USART_DMA.stream, (u32) data);
dma_set_number_of_data(USART_DMA.dma, USART_DMA.stream, len);
dma_set_read_from_memory(USART_DMA.dma, USART_DMA.stream); /* direction is from memory to usart */
dma_enable_memory_increment_mode(USART_DMA.dma, USART_DMA.stream); /* memory pointer increments, peripheral no */
dma_set_peripheral_size(USART_DMA.dma, USART_DMA.stream, DMA_SxCR_PSIZE_8BIT); /* USART_DR is 8bit wide in this mode */
dma_set_memory_size(USART_DMA.dma, USART_DMA.stream, DMA_SxCR_MSIZE_8BIT); /* destination memory is also 8 bit wide */
dma_set_priority(USART_DMA.dma, USART_DMA.stream, DMA_CCR_PL_LOW);
dma_enable_transfer_complete_interrupt(USART_DMA.dma, USART_DMA.stream);
DMA_channel_select(USART_DMA);
DMA_enable_stream(USART_DMA); /* dma ready to go */
usart_enable_tx_dma(UART_CFG.uart);
return 0;
}
void acq_init()
{
/* Initialize amplifier control GPIO */
gpio_mode_setup(BANK_AMP, GPIO_MODE_OUTPUT, GPIO_PUPD_NONE, GPIO_AMP);
gpio_clear(BANK_AMP, GPIO_AMP);
gpio_mode_setup(BANK_LED, GPIO_MODE_OUTPUT, GPIO_PUPD_NONE, GPIO_LED);
gpio_clear(BANK_LED, GPIO_LED);
/* Initialize SPI GPIOs */
gpio_mode_setup(BANK_CS, GPIO_MODE_AF, GPIO_PUPD_NONE, GPIO_CS);
gpio_mode_setup(BANK_SCLK, GPIO_MODE_AF, GPIO_PUPD_NONE, GPIO_SCLK);
gpio_mode_setup(BANK_DOUT, GPIO_MODE_AF, GPIO_PUPD_NONE, GPIO_DOUT);
gpio_set_af(BANK_CS, GPIO_AF6, GPIO_CS);
gpio_set_af(BANK_SCLK, GPIO_AF6, GPIO_SCLK);
gpio_set_af(BANK_DOUT, GPIO_AF6, GPIO_DOUT);
rcc_periph_clock_enable(RCC_SPI3);
acq_spi_init(SPI_C1);
rcc_periph_clock_enable(RCC_DMA1);
dma_channel_reset(DMA1, DMA_CHANNEL2);
dma_disable_channel(DMA1, DMA_CHANNEL2);
dma_set_peripheral_address(DMA1, DMA_CHANNEL2, (uint32_t)&SPI_DR(SPI_C1));
dma_set_memory_address(DMA1, DMA_CHANNEL2, (uint32_t)&acq_channel.buff);
dma_set_number_of_data(DMA1, DMA_CHANNEL2, BUFFER_SIZE);
dma_set_priority(DMA1, DMA_CHANNEL2, DMA_CCR_PL_MEDIUM);
dma_set_memory_size(DMA1, DMA_CHANNEL2, DMA_CCR_MSIZE_16BIT);
dma_set_peripheral_size(DMA1, DMA_CHANNEL2, DMA_CCR_PSIZE_16BIT);
dma_enable_memory_increment_mode(DMA1, DMA_CHANNEL2);
dma_set_read_from_peripheral(DMA1, DMA_CHANNEL2);
dma_enable_circular_mode(DMA1, DMA_CHANNEL2);
nvic_set_priority(NVIC_DMA1_CHANNEL2_IRQ, PRIO_ACQ);
}
static void platform_init_adc() {
/* Set up DMA for the ADC */
nvic_enable_irq(NVIC_DMA2_STREAM0_IRQ);
nvic_set_priority(NVIC_DMA2_STREAM0_IRQ, 64);
/* Set up ADC */
for (int i = 0; i < NUM_SENSORS; ++i) {
if (config.sensors[i].method == SENSOR_ADC) {
adc_pins[i] = config.sensors[i].pin;
gpio_mode_setup(GPIOA, GPIO_MODE_ANALOG, GPIO_PUPD_NONE, (1<<adc_pins[i]));
}
}
adc_off(ADC1);
adc_enable_scan_mode(ADC1);
adc_set_sample_time_on_all_channels(ADC1, ADC_SMPR_SMP_15CYC);
adc_power_on(ADC1);
adc_disable_dma(ADC1);
adc_enable_dma(ADC1);
adc_clear_overrun_flag(ADC1);
adc_set_dma_continue(ADC1);
dma_stream_reset(DMA2, DMA_STREAM0);
dma_set_priority(DMA2, DMA_STREAM0, DMA_SxCR_PL_HIGH);
dma_set_memory_size(DMA2, DMA_STREAM0, DMA_SxCR_MSIZE_16BIT);
dma_set_peripheral_size(DMA2, DMA_STREAM0, DMA_SxCR_PSIZE_16BIT);
dma_enable_memory_increment_mode(DMA2, DMA_STREAM0);
dma_set_transfer_mode(DMA2, DMA_STREAM0, DMA_SxCR_DIR_PERIPHERAL_TO_MEM);
dma_enable_circular_mode(DMA2, DMA_STREAM0);
dma_set_peripheral_address(DMA2, DMA_STREAM0, (uint32_t) &ADC1_DR);
dma_set_memory_address(DMA2, DMA_STREAM0, (uint32_t) adc_dma_buf);
dma_set_number_of_data(DMA2, DMA_STREAM0, NUM_SENSORS);
dma_enable_transfer_complete_interrupt(DMA2, DMA_STREAM0);
dma_channel_select(DMA2, DMA_STREAM0, DMA_SxCR_CHSEL_0);
dma_enable_stream(DMA2, DMA_STREAM0);
adc_set_regular_sequence(ADC1, NUM_SENSORS, adc_pins);
}
static int timer_dma(uint8_t *tx_buf, int tx_len)
{
dma_int_enable();
/* Reset DMA channels*/
dma_channel_reset(DMA1, DMA_CHANNEL3);
/* Set up tx dma */
dma_set_peripheral_address(DMA1, DMA_CHANNEL3, (uint32_t)&TIM_CCR2(TIM3));
dma_set_memory_address(DMA1, DMA_CHANNEL3, (uint32_t)tx_buf);
dma_set_number_of_data(DMA1, DMA_CHANNEL3, tx_len);
dma_set_read_from_memory(DMA1, DMA_CHANNEL3);
dma_enable_memory_increment_mode(DMA1, DMA_CHANNEL3);
dma_set_peripheral_size(DMA1, DMA_CHANNEL3, DMA_CCR_PSIZE_32BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL3, DMA_CCR_MSIZE_8BIT);
dma_set_priority(DMA1, DMA_CHANNEL3, DMA_CCR_PL_HIGH);
dma_enable_circular_mode(DMA1, DMA_CHANNEL3);
dma_enable_transfer_complete_interrupt(DMA1, DMA_CHANNEL3);
dma_enable_half_transfer_interrupt(DMA1, DMA_CHANNEL3);
dma_enable_channel(DMA1, DMA_CHANNEL3);
return 0;
}
/*--------------------------------------------------------------------*/
void dma_setup(void)
{
rcc_peripheral_enable_clock(&RCC_AHB1ENR, RCC_AHB1ENR_DMA2EN);
/* ADC1 uses DMA controller 2 Stream 0 channel 0. */
/* Enable DMA2 clock and IRQ */
nvic_enable_irq(NVIC_DMA2_STREAM0_IRQ);
dma_stream_reset(DMA2,DMA_STREAM0);
dma_set_priority(DMA2,DMA_STREAM0,DMA_SxCR_PL_LOW);
dma_set_peripheral_size(DMA2,DMA_STREAM0,DMA_SxCR_PSIZE_32BIT);
/* The register to target is the ADC regular data register */
dma_set_peripheral_address(DMA2,DMA_STREAM0,(uint32_t) &ADC1_DR);
/* The array v[] is filled with the waveform data to be output */
dma_set_memory_size(DMA2,DMA_STREAM0,DMA_SxCR_MSIZE_32BIT);
dma_set_memory_address(DMA2,DMA_STREAM0,(uint32_t) v);
dma_set_number_of_data(DMA2,DMA_STREAM0,64);
dma_set_transfer_mode(DMA2,DMA_STREAM0, DMA_SxCR_DIR_PERIPHERAL_TO_MEM);
dma_enable_memory_increment_mode(DMA2,DMA_STREAM0);
dma_enable_circular_mode(DMA2,DMA_STREAM0);
/* Don't use FIFO */
dma_enable_direct_mode(DMA2,DMA_STREAM0);
dma_enable_transfer_complete_interrupt(DMA2, DMA_STREAM0);
dma_channel_select(DMA2, DMA_STREAM0, DMA_SxCR_CHSEL_0);
dma_enable_stream(DMA2,DMA_STREAM0);
}
/*--------------------------------------------------------------------*/
static void dma_setup(void)
{
/* DAC channel 1 uses DMA controller 1 Stream 5 Channel 7. */
/* Enable DMA1 clock and IRQ */
rcc_periph_clock_enable(RCC_DMA1);
nvic_enable_irq(NVIC_DMA1_STREAM5_IRQ);
dma_stream_reset(DMA1, DMA_STREAM5);
dma_set_priority(DMA1, DMA_STREAM5, DMA_SxCR_PL_LOW);
dma_set_memory_size(DMA1, DMA_STREAM5, DMA_SxCR_MSIZE_8BIT);
dma_set_peripheral_size(DMA1, DMA_STREAM5, DMA_SxCR_PSIZE_8BIT);
dma_enable_memory_increment_mode(DMA1, DMA_STREAM5);
dma_enable_circular_mode(DMA1, DMA_STREAM5);
dma_set_transfer_mode(DMA1, DMA_STREAM5,
DMA_SxCR_DIR_MEM_TO_PERIPHERAL);
/* The register to target is the DAC1 8-bit right justified data
register */
dma_set_peripheral_address(DMA1, DMA_STREAM5, (uint32_t) &DAC_DHR8R1);
/* The array v[] is filled with the waveform data to be output */
dma_set_memory_address(DMA1, DMA_STREAM5, (uint32_t) waveform);
dma_set_number_of_data(DMA1, DMA_STREAM5, 256);
dma_enable_transfer_complete_interrupt(DMA1, DMA_STREAM5);
dma_channel_select(DMA1, DMA_STREAM5, DMA_SxCR_CHSEL_7);
dma_enable_stream(DMA1, DMA_STREAM5);
}
/**
* Initialize analog to digital converter
*/
void adc_init(adc_callback_t half_transfer_callback,
adc_callback_t transfer_complete_callback)
{
/* Reset adc_state. */
adc_state.dma_transfer_error_counter = 0;
adc_state.half_transfer_callback = half_transfer_callback;
adc_state.transfer_complete_callback = transfer_complete_callback;
/* Initialize peripheral clocks. */
rcc_peripheral_enable_clock(&RCC_AHBENR, RCC_AHBENR_DMA1EN);
rcc_peripheral_enable_clock(&RCC_APB2ENR, RCC_APB2ENR_IOPAEN);
rcc_peripheral_enable_clock(&RCC_APB2ENR, RCC_APB2ENR_ADC1EN);
rcc_peripheral_enable_clock(&RCC_APB2ENR, RCC_APB2ENR_ADC2EN);
/* Initialize the ADC input GPIO. */
/* WARNING: this code is written to work with strip. On the strip
* hardware we are lucky and all the ADC channels are on the same bank
* so we can initialize all of them in one go. This code will need to be
* changed/improved if we ever have to support hardware that has the
* ADC's spread over more then one bank.
*/
gpio_set_mode(ADC_BANK, GPIO_MODE_INPUT,
GPIO_CNF_INPUT_ANALOG, ADC_PORT_U_VOLTAGE |
ADC_PORT_V_VOLTAGE |
ADC_PORT_W_VOLTAGE |
ADC_PORT_V_BATT |
ADC_PORT_CURRENT);
/* Configure DMA for data aquisition. */
/* Channel 1 reacts to: ADC1, TIM2_CH3 and TIM4_CH1 */
dma_channel_reset(DMA1, DMA_CHANNEL1);
dma_set_peripheral_address(DMA1, DMA_CHANNEL1, (uint32_t)&ADC1_DR);
dma_set_memory_address(DMA1, DMA_CHANNEL1,
(uint32_t)adc_state.raw_data);
dma_set_number_of_data(DMA1, DMA_CHANNEL1, ADC_RAW_SAMPLE_COUNT/2);
dma_set_read_from_peripheral(DMA1, DMA_CHANNEL1);
dma_enable_memory_increment_mode(DMA1, DMA_CHANNEL1);
dma_enable_circular_mode(DMA1, DMA_CHANNEL1);
dma_set_peripheral_size(DMA1, DMA_CHANNEL1, DMA_CCR_PSIZE_32BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL1, DMA_CCR_MSIZE_32BIT);
dma_set_priority(DMA1, DMA_CHANNEL1, DMA_CCR_PL_VERY_HIGH);
dma_enable_half_transfer_interrupt(DMA1, DMA_CHANNEL1);
dma_enable_transfer_complete_interrupt(DMA1, DMA_CHANNEL1);
dma_enable_transfer_error_interrupt(DMA1, DMA_CHANNEL1);
dma_enable_channel(DMA1, DMA_CHANNEL1);
/* Configure interrupts in NVIC. */
nvic_set_priority(NVIC_DMA1_CHANNEL1_IRQ, 0);
nvic_enable_irq(NVIC_DMA1_CHANNEL1_IRQ);
/* Disable ADC's. */
adc_off(ADC1);
adc_off(ADC2);
/* Enable dualmode. */
adc_set_dual_mode(ADC_CR1_DUALMOD_RSM); /* Dualmode regular only. */
/* Configure the adc channels. */
adc_config(ADC1, adc1_channel_array);
adc_config(ADC2, adc2_channel_array);
/* Start converting. */
adc_start_conversion_regular(ADC1);
}
void accel_highg_init()
{
uint8_t channel_array[16];
gpio_set_mode(GPIOB, GPIO_MODE_INPUT,
GPIO_CNF_INPUT_ANALOG, GPIO0 | GPIO1 | GPIO2);
adc_set_dual_mode(ADC_CR1_DUALMOD_RSM);
/* ADC1 + ADC2 dual mode */
adc_set_dual_mode(ADC_CR1_DUALMOD_ISM);
adc_enable_external_trigger_injected(ADC1, ADC_CR2_JEXTSEL_TIM1_TRGO);
adc_enable_external_trigger_injected(ADC3, ADC_CR2_JEXTSEL_TIM1_TRGO);
adc_enable_dma(ADC1);
adc_enable_dma(ADC3);
adc_power_on(ADC1);
adc_power_on(ADC2);
adc_power_on(ADC3);
adc_stab_sleep();
adc_reset_calibration(ADC1);
adc_reset_calibration(ADC2);
adc_reset_calibration(ADC3);
adc_calibration(ADC1);
adc_calibration(ADC2);
adc_calibration(ADC3);
memset(channel_array, 0, sizeof(channel_array));
channel_array[0] = 10;
adc_set_injected_sequence(ADC1, 1, channel_array);
channel_array[0] = 11;
adc_set_injected_sequence(ADC2, 1, channel_array);
channel_array[0] = 12;
adc_set_injected_sequence(ADC3, 1, channel_array);
timer_reset(TIM1);
timer_enable_irq(TIM1, TIM_DIER_UIE);
timer_set_mode(TIM1, TIM_CR1_CKD_CK_INT,
TIM_CR1_CMS_EDGE, TIM_CR1_DIR_UP);
/* 500Hz */
timer_set_prescaler(TIM1, 64);
timer_set_period(TIM1, 2250);
/* Generate TRGO */
timer_set_master_mode(TIM1, TIM_CR2_MMS_UPDATE);
dma_set_peripheral_address(DMA1, DMA_CHANNEL5, (uint32_t) &ADC1_DR);
dma_set_read_from_memory(DMA1, DMA_CHANNEL5);
dma_enable_memory_increment_mode(DMA1, DMA_CHANNEL5);
dma_set_peripheral_size(DMA1, DMA_CHANNEL5, DMA_CCR_PSIZE_32BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL5, DMA_CCR_MSIZE_32BIT);
dma_set_priority(DMA1, DMA_CHANNEL5, DMA_CCR_PL_HIGH);
dma_set_peripheral_address(DMA1, DMA_CHANNEL6, (uint32_t) &ADC3_DR);
dma_set_read_from_peripheral(DMA1, DMA_CHANNEL6);
dma_enable_memory_increment_mode(DMA1, DMA_CHANNEL6);
dma_set_peripheral_size(DMA1, DMA_CHANNEL6, DMA_CCR_PSIZE_16BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL6, DMA_CCR_MSIZE_16BIT);
dma_set_priority(DMA1, DMA_CHANNEL6, DMA_CCR_PL_HIGH);
dma_enable_transfer_complete_interrupt(DMA1, DMA_CHANNEL5);
dma_enable_transfer_complete_interrupt(DMA1, DMA_CHANNEL6);
}
void ws2812_init( void )
{
uint32_t i,j;
for( i = 0; i < WS2812_BUFFERSIZE; i++ )
{
bitframe_pattern[i] = 0;
bitframe_pattern_draw[i] = 0;
}
for( i=0; i < (3*NR_OF_LEDS_PER_CH*NR_OF_ROWS); i++)
{
frame_pattern[i] = 0;
}
/* configure the GPIOs */
/* Enable GPIOC clock */
rcc_periph_clock_enable(RCC_GPIOB);
/* Setup GPIO pin GPIO8/9 on GPIO port C for LEDs. */
gpio_mode_setup(GPIOB, GPIO_MODE_OUTPUT, GPIO_PUPD_PULLDOWN, GPIO0);
gpio_set_output_options( GPIOB, GPIO_OTYPE_PP, GPIO_OSPEED_HIGH, GPIO0);
/* configure the DMA */
rcc_periph_clock_enable(RCC_DMA);
/* configure DMA for sending high constant pattern to port on begin of cycle
* send unrolled bitframe on Timer OC1 event
* send low on Timer OC3 event
*/
dma_channel_reset( DMA1, DMA_CHANNEL3);
dma_set_peripheral_address( DMA1, DMA_CHANNEL3, (uint32_t)&GPIOB_ODR);
dma_set_memory_address( DMA1, DMA_CHANNEL3, (uint32_t)&high_pattern);
dma_set_peripheral_size( DMA1, DMA_CHANNEL3, DMA_CCR_PSIZE_8BIT);
dma_set_memory_size( DMA1, DMA_CHANNEL3, DMA_CCR_MSIZE_8BIT);
dma_disable_peripheral_increment_mode( DMA1, DMA_CHANNEL3 );
dma_disable_memory_increment_mode( DMA1, DMA_CHANNEL3 );
dma_set_priority( DMA1, DMA_CHANNEL3, DMA_CCR_PL_HIGH);
dma_set_read_from_memory(DMA1, DMA_CHANNEL3);
dma_channel_reset( DMA1, DMA_CHANNEL4);
dma_set_peripheral_address( DMA1, DMA_CHANNEL4, (uint32_t)&GPIOB_ODR);
dma_set_memory_address( DMA1, DMA_CHANNEL4, (uint32_t)actual_bitframe);
dma_set_peripheral_size( DMA1, DMA_CHANNEL4, DMA_CCR_PSIZE_8BIT);
dma_set_memory_size( DMA1, DMA_CHANNEL4, DMA_CCR_MSIZE_8BIT);
dma_disable_peripheral_increment_mode( DMA1, DMA_CHANNEL4 );
dma_enable_memory_increment_mode( DMA1, DMA_CHANNEL4 );
dma_set_priority( DMA1, DMA_CHANNEL4, DMA_CCR_PL_HIGH);
dma_set_read_from_memory(DMA1, DMA_CHANNEL4);
dma_channel_reset( DMA1, DMA_CHANNEL2);
dma_set_peripheral_address( DMA1, DMA_CHANNEL2, (uint32_t)&GPIOB_ODR);
dma_set_memory_address( DMA1, DMA_CHANNEL2, (uint32_t)&low_pattern);
dma_set_peripheral_size( DMA1, DMA_CHANNEL2, DMA_CCR_PSIZE_8BIT);
dma_set_memory_size( DMA1, DMA_CHANNEL2, DMA_CCR_MSIZE_8BIT);
dma_disable_peripheral_increment_mode( DMA1, DMA_CHANNEL2 );
dma_disable_memory_increment_mode( DMA1, DMA_CHANNEL2 );
dma_set_priority( DMA1, DMA_CHANNEL2, DMA_CCR_PL_HIGH);
dma_set_read_from_memory(DMA1, DMA_CHANNEL2);
nvic_set_priority(NVIC_DMA1_CHANNEL2_3_IRQ, 0);
nvic_enable_irq(NVIC_DMA1_CHANNEL2_3_IRQ);
dma_enable_transfer_complete_interrupt( DMA1, DMA_CHANNEL2);
/* configure timer */
rcc_periph_clock_enable(RCC_TIM3);
/* configure the timer for 800kHz overall frequency */
timer_reset( TIM3 );
timer_set_mode( TIM3, TIM_CR1_CKD_CK_INT, TIM_CR1_CMS_EDGE, TIM_CR1_DIR_UP);
timer_set_period( TIM3, 60);
timer_set_repetition_counter( TIM3, 0);
timer_disable_preload( TIM3 );
/* timer compare section 1 for low coding */
timer_set_oc_mode( TIM3, TIM_OC1,TIM_OCM_FROZEN);
timer_set_oc_value( TIM3, TIM_OC1, 19);
timer_disable_oc_preload( TIM3, TIM_OC1);
/* timer compare section 3 for high coding */
timer_set_oc_mode( TIM3, TIM_OC3,TIM_OCM_FROZEN);
timer_set_oc_value( TIM3, TIM_OC3, 41);
timer_disable_oc_preload( TIM3, TIM_OC3);
nvic_set_priority( NVIC_TIM3_IRQ,1);
nvic_set_priority( NVIC_PENDSV_IRQ, 2);
nvic_enable_irq(NVIC_TIM3_IRQ);
nvic_enable_irq(NVIC_PENDSV_IRQ);
/* start the sending process */
ws2812_send();
}
bool TSpiDmaQueue::TryStartJob()
{
// Start the next DMA job in the queue if the SPI interface is
// available (TXE=1 and BSY=0)
// We treat both SPI busses (flash and display) as one, so no concurrent jobs
// are allowed.
const uint32_t spi = LCD_SPI_CHANNEL;
if ((SPI_SR(spi) & SPI_SR_TXE) && (~SPI_SR(spi) & SPI_SR_BSY)) {
if (Jobs.Empty()) {
return false;
}
const TSpiDmaJob& job = Jobs.First();
const TBuffer& buffer = job.GetBuffer();
// SPI receive register should be empty here!
assert(!(SPI_SR(spi) & SPI_SR_RXNE));
const uint32_t dma = DMA1;
{
const uint32_t channel = (job.GetChip() == TSpiDmaJob::CS_LCD) ? LCD_DMA_TX_CHANNEL : FLASH_DMA_TX_CHANNEL;
dma_channel_reset(dma, channel);
dma_set_peripheral_address(dma, channel, reinterpret_cast<uint32_t>(&SPI_DR(spi)));
dma_set_memory_address(dma, channel, reinterpret_cast<uint32_t>(buffer.GetData()));
dma_set_number_of_data(dma, channel, buffer.GetLength());
dma_set_read_from_memory(dma, channel);
dma_enable_memory_increment_mode(dma, channel);
dma_set_peripheral_size(dma, channel, DMA_CCR_PSIZE_8BIT);
dma_set_memory_size(dma, channel, DMA_CCR_MSIZE_8BIT);
dma_set_priority(dma, channel, DMA_CCR_PL_LOW);
//dma_enable_transfer_complete_interrupt(dma, channel);
dma_enable_channel(dma, channel);
}
{
const uint32_t channel = (job.GetChip() == TSpiDmaJob::CS_LCD) ? LCD_DMA_RX_CHANNEL : FLASH_DMA_RX_CHANNEL;
dma_channel_reset(dma, channel);
dma_set_peripheral_address(dma, channel, reinterpret_cast<uint32_t>(&SPI_DR(spi)));
dma_set_memory_address(dma, channel, reinterpret_cast<uint32_t>(buffer.GetData()));
dma_set_number_of_data(dma, channel, buffer.GetLength());
dma_enable_memory_increment_mode(dma, channel);
dma_set_peripheral_size(dma, channel, DMA_CCR_PSIZE_8BIT);
dma_set_memory_size(dma, channel, DMA_CCR_MSIZE_8BIT);
dma_set_priority(dma, channel, DMA_CCR_PL_LOW);
dma_enable_transfer_complete_interrupt(dma, channel);
dma_enable_channel(dma, channel);
}
// Set CS and LCD_A0 lines
Pin_lcd_cs.Clear();
if (job.GetLcdData()) {
Pin_lcd_a0.Set();
} else {
Pin_lcd_a0.Clear();
}
// Kick off the transfer
spi_enable_rx_dma(spi);
spi_enable_tx_dma(spi);
return true;
}
return false;
}
static void setup_i2c_port(enum I2C_FREQ I2C_speed)
{
// Disable I2C if it happens to be enabled
i2c_peripheral_disable(I2C_PORT);
dma_channel_reset(I2C_TX_DMA, I2C_TX_DMA_CHANNEL);
i2c_disable_interrupt(I2C_PORT, (I2C_CR2_ITEVTEN | I2C_CR2_ITERREN));
DISABLE_I2C_INTERRUPT();
reset_i2c_pins();
// set: Source, Destination, and Amount (DMA channel must be disabled)
dma_set_peripheral_address(I2C_TX_DMA, I2C_TX_DMA_CHANNEL, (uint32_t)&I2C_DR(I2C_PORT));
dma_set_memory_address(I2C_TX_DMA, I2C_TX_DMA_CHANNEL, 0);
dma_set_number_of_data(I2C_TX_DMA, I2C_TX_DMA_CHANNEL, 0);
// set the DMA Configuration (DMA_CCRx)
// (BIT 14) mem2mem_mode disabled
dma_set_priority(I2C_TX_DMA, I2C_TX_DMA_CHANNEL, DMA_CCR_PL_HIGH); // (BIT 12:13)
dma_set_memory_size(I2C_TX_DMA, I2C_TX_DMA_CHANNEL, DMA_CCR_MSIZE_8BIT); // (BIT 10:11)
dma_set_peripheral_size(I2C_TX_DMA, I2C_TX_DMA_CHANNEL, DMA_CCR_PSIZE_8BIT); // (BIT 8:9)
dma_enable_memory_increment_mode(I2C_TX_DMA, I2C_TX_DMA_CHANNEL); // (BIT 7)
dma_disable_peripheral_increment_mode(I2C_TX_DMA, I2C_TX_DMA_CHANNEL); // (BIT 6)
// (BIT 5) Circular mode is disabled
dma_set_read_from_memory(I2C_TX_DMA, I2C_TX_DMA_CHANNEL); // (BIT 4)
dma_enable_transfer_error_interrupt(I2C_TX_DMA, I2C_TX_DMA_CHANNEL); // (BIT 3)
dma_disable_half_transfer_interrupt(I2C_TX_DMA, I2C_TX_DMA_CHANNEL); // (BIT 2)
dma_enable_transfer_complete_interrupt(I2C_TX_DMA, I2C_TX_DMA_CHANNEL); // (BIT 1)
// This is the slave address when not transmitting data
i2c_set_own_7bit_slave_address(I2C_PORT, 0x32);
// do not respond to the specified slave address
i2c_disable_ack(I2C_PORT);
// Use DMA to send I2C data
i2c_enable_dma(I2C_PORT);
// set which interrupts I2C uses
i2c_enable_interrupt(I2C_PORT, (I2C_CR2_ITEVTEN | I2C_CR2_ITERREN));
// APB1 is running at 36MHz = T(PCLK1) = 1/36000000 sec.
i2c_set_clock_frequency(I2C_PORT, I2C_CR2_FREQ_36MHZ);
// Set up the hardware for the particular speed
switch (I2C_speed) {
// Values found on Internet for the I2C standard
// STANDARD : SCL max rise time = 1000ns = 1000/1000000000 sec
// FAST : SCL max rise time = 300ns = 300/1000000000 sec
//
// DATASHEET Function:
// TRISE = (T(MAX_SCL_RISE) / T(PCLK1)) + 1
//
// DATASHEET Functions:
// STANDARD :
// T(high) = CCR * T(PCLK1)
// T(low) = CCR * T(PCLK1)
// FAST (DUTY=I2C_CCR_DUTY_DIV2)
// T(high) = CCR * T(PCLK1)
// T(low) = 2 * CCR * T(PCLK1)
// FAST (DUTY=I2C_CCR_DUTY_16_DIV_9) [To reach 400KHz]
// T(high) = 9 * CCR * T(PCLK1)
// T(low) = 16 * CCR * T(PCLK1)
//
// I2C PERIOD:
// STANDARD
// PERIOD = T(high) + T(low) = (2 * CCR * T(PCLK1))
// FAST (DUTY=I2C_CCR_DUTY_DIV2)
// PERIOD = T(high) + T(low) = (3 * CCR * T(PCLK1))
// FAST (DUTY=I2C_CCR_DUTY_16_DIV_9)
// PERIOD = T(high) + T(low) = (25 * CCR * T(PCLK1))
case I2C_400KHz:
// I2C PERIOD: 400KHz = 400000Hz = 1/400000 sec.
i2c_set_fast_mode(I2C_PORT);
// I2C_CCR_DUTY_DIV2 or I2C_CCR_DUTY_16_DIV_9
i2c_set_dutycycle(I2C_PORT, I2C_CCR_DUTY_16_DIV_9);
// CCR = PERIOD / (25 * T(PCLK1))
// CCR = (1/400000) / (25/36000000) = 18/5 = 3.6
// CCR = 4 => I2C PERIOD = 360kHz
// CCR = 3 => I2C PERIOD = 480kHz
i2c_set_ccr(I2C_PORT, 4); // Only fast mode can have a value less than 0x04
// TRISE = ( (300/1000000000) / (1/36000000) ) + 1 = 59/5 = 11.8
// TRISE = 12 => SCL max rise time ~= 305.555ns
// TRISE = 11 => SCL max rise time ~= 277.777ns
i2c_set_trise(I2C_PORT, 11);
break;
case I2C_100KHz:
// I2C PERIOD: 100KHz = 100000Hz = 1/100000 sec.
i2c_set_standard_mode(I2C_PORT);
// I2C_CCR_DUTY_DIV2 or I2C_CCR_DUTY_16_DIV_9
i2c_set_dutycycle(I2C_PORT, I2C_CCR_DUTY_DIV2);
// CCR = PERIOD / (2 * T(PCLK1))
// CCR = (1/100000) / (2/36000000) = 180
i2c_set_ccr(I2C_PORT, 180);
// TRISE = ( (1000/1000000000) / (1/36000000) ) + 1 = 37
i2c_set_trise(I2C_PORT, 37);
break;
case I2C_53KHz:
// ~= 52.91kHz is the slowest I could get to work
// CCR value of 341 works but not 342 or higher
case I2C_50KHz:
default:
// I2C PERIOD: 50KHz = 50000Hz = 1/50000 sec.
i2c_set_standard_mode(I2C_PORT);
// I2C_CCR_DUTY_DIV2 or I2C_CCR_DUTY_16_DIV_9
i2c_set_dutycycle(I2C_PORT, I2C_CCR_DUTY_DIV2);
// CCR = PERIOD / (2 * T(PCLK1))
// CCR = (1/50000) / (2/36000000) = 360
// (341 works but not 342 or higher)
i2c_set_ccr(I2C_PORT, 341);
// TRISE = ( (1000/1000000000) / (1/36000000) ) + 1 = 37
i2c_set_trise(I2C_PORT, 37);
break;
}
i2c_peripheral_enable(I2C_PORT);
// set the priorities for the interrupts
nvic_set_priority(I2C_EV_IRQ, IRQ_PRI_I2C);
nvic_set_priority(I2C_ER_IRQ, IRQ_PRI_ER_I2C);
nvic_set_priority(I2C_DMA_IRQ, IRQ_PRI_DMA_I2C);
}
static int spi_dma_transceive(uint8_t *tx_buf, int tx_len, uint8_t *rx_buf, int rx_len)
#endif
{
/* Check for 0 length in both tx and rx */
if ((rx_len < 1) && (tx_len < 1)) {
/* return -1 as error */
return -1;
}
/* Reset DMA channels*/
dma_channel_reset(DMA1, DMA_CHANNEL2);
dma_channel_reset(DMA1, DMA_CHANNEL3);
/* Reset SPI data and status registers.
* Here we assume that the SPI peripheral is NOT
* busy any longer, i.e. the last activity was verified
* complete elsewhere in the program.
*/
volatile uint8_t temp_data __attribute__ ((unused));
while (SPI_SR(SPI1) & (SPI_SR_RXNE | SPI_SR_OVR)) {
temp_data = SPI_DR(SPI1);
}
/* Reset status flag appropriately (both 0 case caught above) */
transceive_status = NONE;
if (rx_len < 1) {
transceive_status = ONE;
}
/* Determine tx length case to change behaviour
* If tx_len >= rx_len, then normal case, run both DMAs with normal settings
* If rx_len == 0, just don't run the rx DMA at all
* If tx_len == 0, use a dummy buf and set the tx dma to transfer the same
* amount as the rx_len, to ensure everything is clocked in
* If 0 < tx_len < rx_len, first do a normal case, then on the tx finished
* interrupt, set up a new dummyy buf tx dma transfer for the remaining
* required clock cycles (handled in tx dma complete interrupt)
*/
if ((tx_len > 0) && (tx_len < rx_len)) {
rx_buf_remainder = rx_len - tx_len;
}
/* Set up rx dma, note it has higher priority to avoid overrun */
if (rx_len > 0) {
dma_set_peripheral_address(DMA1, DMA_CHANNEL2, (uint32_t)&SPI1_DR);
dma_set_memory_address(DMA1, DMA_CHANNEL2, (uint32_t)rx_buf);
dma_set_number_of_data(DMA1, DMA_CHANNEL2, rx_len);
dma_set_read_from_peripheral(DMA1, DMA_CHANNEL2);
dma_enable_memory_increment_mode(DMA1, DMA_CHANNEL2);
#if USE_16BIT_TRANSFERS
dma_set_peripheral_size(DMA1, DMA_CHANNEL2, DMA_CCR_PSIZE_16BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL2, DMA_CCR_MSIZE_16BIT);
#else
dma_set_peripheral_size(DMA1, DMA_CHANNEL2, DMA_CCR_PSIZE_8BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL2, DMA_CCR_MSIZE_8BIT);
#endif
dma_set_priority(DMA1, DMA_CHANNEL2, DMA_CCR_PL_VERY_HIGH);
}
/* Set up tx dma (must always run tx to get clock signal) */
if (tx_len > 0) {
/* Here we have a regular tx transfer */
dma_set_peripheral_address(DMA1, DMA_CHANNEL3, (uint32_t)&SPI1_DR);
dma_set_memory_address(DMA1, DMA_CHANNEL3, (uint32_t)tx_buf);
dma_set_number_of_data(DMA1, DMA_CHANNEL3, tx_len);
dma_set_read_from_memory(DMA1, DMA_CHANNEL3);
dma_enable_memory_increment_mode(DMA1, DMA_CHANNEL3);
#if USE_16BIT_TRANSFERS
dma_set_peripheral_size(DMA1, DMA_CHANNEL3, DMA_CCR_PSIZE_16BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL3, DMA_CCR_MSIZE_16BIT);
#else
dma_set_peripheral_size(DMA1, DMA_CHANNEL3, DMA_CCR_PSIZE_8BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL3, DMA_CCR_MSIZE_8BIT);
#endif
dma_set_priority(DMA1, DMA_CHANNEL3, DMA_CCR_PL_HIGH);
} else {
/* Here we aren't transmitting any real data, use the dummy buffer
* and set the length to the rx_len to get all rx data in, while
* not incrementing the memory pointer
*/
dma_set_peripheral_address(DMA1, DMA_CHANNEL3, (uint32_t)&SPI1_DR);
dma_set_memory_address(DMA1, DMA_CHANNEL3, (uint32_t)(&dummy_tx_buf)); // Change here
dma_set_number_of_data(DMA1, DMA_CHANNEL3, rx_len); // Change here
dma_set_read_from_memory(DMA1, DMA_CHANNEL3);
dma_disable_memory_increment_mode(DMA1, DMA_CHANNEL3); // Change here
#if USE_16BIT_TRANSFERS
dma_set_peripheral_size(DMA1, DMA_CHANNEL3, DMA_CCR_PSIZE_16BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL3, DMA_CCR_MSIZE_16BIT);
#else
dma_set_peripheral_size(DMA1, DMA_CHANNEL3, DMA_CCR_PSIZE_8BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL3, DMA_CCR_MSIZE_8BIT);
#endif
dma_set_priority(DMA1, DMA_CHANNEL3, DMA_CCR_PL_HIGH);
}
/* Enable dma transfer complete interrupts */
if (rx_len > 0) {
dma_enable_transfer_complete_interrupt(DMA1, DMA_CHANNEL2);
}
dma_enable_transfer_complete_interrupt(DMA1, DMA_CHANNEL3);
/* Activate dma channels */
if (rx_len > 0) {
dma_enable_channel(DMA1, DMA_CHANNEL2);
}
dma_enable_channel(DMA1, DMA_CHANNEL3);
/* Enable the spi transfer via dma
* This will immediately start the transmission,
* after which when the receive is complete, the
* receive dma will activate
*/
if (rx_len > 0) {
spi_enable_rx_dma(SPI1);
}
spi_enable_tx_dma(SPI1);
return 0;
}
void codecInit(void)
{
memset(adcBuffer, 0xaa, sizeof(adcBuffer));
// I2S2 alternate function mapping
gpio_mode_setup(GPIOB, GPIO_MODE_AF, GPIO_PUPD_NONE, GPIO12 | GPIO13 | GPIO14 | GPIO15);
gpio_set_af(GPIOB, GPIO_AF5, GPIO12 | GPIO13 | GPIO15);
gpio_set_af(GPIOB, GPIO_AF6, GPIO14); // I2S2ext_SD (I2S receive)
gpio_mode_setup(GPIOC, GPIO_MODE_AF, GPIO_PUPD_NONE, GPIO6);
gpio_set_af(GPIOC, GPIO_AF5, GPIO6); // MCLK
gpio_set_output_options(GPIOB, GPIO_OTYPE_PP, GPIO_OSPEED_25MHZ, GPIO12 | GPIO13 | GPIO15);
gpio_set_output_options(GPIOC, GPIO_OTYPE_PP, GPIO_OSPEED_100MHZ, GPIO6);
// Set up SPI1
spi_reset(SPI1);
spi_init_master(SPI1, SPI_CR1_BAUDRATE_FPCLK_DIV_256, SPI_CR1_CPOL_CLK_TO_1_WHEN_IDLE,
SPI_CR1_CPHA_CLK_TRANSITION_2, SPI_CR1_DFF_16BIT, SPI_CR1_MSBFIRST);
spi_set_nss_high(SPI1);
spi_enable_software_slave_management(SPI1);
spi_enable(SPI1);
// SPI1 alternate function mapping, set CSB signal high output
gpio_mode_setup(GPIOA, GPIO_MODE_AF, GPIO_PUPD_NONE, GPIO5 | GPIO7);
gpio_set_af(GPIOA, GPIO_AF5, GPIO5 | GPIO7);
gpio_set(GPIOA, GPIO4);
gpio_mode_setup(GPIOA, GPIO_MODE_OUTPUT, GPIO_PUPD_NONE, GPIO4);
codecConfig();
// Set up I2S for 48kHz 16-bit stereo.
// The input to the PLLI2S is 1MHz. Division factors are from
// table 126 in the data sheet.
//
// This gives us 1.536MHz SCLK = 16 bits * 2 channels * 48000 Hz
// and 12.288 MHz MCLK = 256 * 48000 Hz.
// With this PLL configuration the actual sampling frequency
// is nominally 47991 Hz.
spi_reset(SPI2);
RCC_PLLI2SCFGR = (3 << 28) | (258 << 6);
RCC_CR |= RCC_CR_PLLI2SON;
while (!(RCC_CR & RCC_CR_PLLI2SRDY));
const unsigned i2sdiv = 3;
SPI_I2SPR(SPI2) = SPI_I2SPR_MCKOE | SPI_I2SPR_ODD | i2sdiv;
SPI_I2SCFGR(SPI2) |= SPI_I2SCFGR_I2SMOD | SPI_I2SCFGR_I2SE |
(SPI_I2SCFGR_I2SCFG_MASTER_TRANSMIT << SPI_I2SCFGR_I2SCFG_LSB);
SPI_I2SCFGR(I2S2_EXT_BASE) = SPI_I2SCFGR_I2SMOD | SPI_I2SCFGR_I2SE |
(SPI_I2SCFGR_I2SCFG_SLAVE_RECEIVE << SPI_I2SCFGR_I2SCFG_LSB);
// Configure the DMA engine to stream data to the DAC.
dma_stream_reset(DMA1, DAC_DMA_STREAM);
dma_set_peripheral_address(DMA1, DAC_DMA_STREAM, (intptr_t)&SPI_DR(SPI2));
dma_set_memory_address(DMA1, DAC_DMA_STREAM, (intptr_t)dacBuffer[0]);
dma_set_memory_address_1(DMA1, DAC_DMA_STREAM, (intptr_t)dacBuffer[1]);
dma_set_number_of_data(DMA1, DAC_DMA_STREAM, BUFFER_SAMPLES);
dma_channel_select(DMA1, DAC_DMA_STREAM, DAC_DMA_CHANNEL);
dma_set_transfer_mode(DMA1, DAC_DMA_STREAM, DMA_SxCR_DIR_MEM_TO_PERIPHERAL);
dma_set_memory_size(DMA1, DAC_DMA_STREAM, DMA_SxCR_MSIZE_16BIT);
dma_set_peripheral_size(DMA1, DAC_DMA_STREAM, DMA_SxCR_PSIZE_16BIT);
dma_enable_memory_increment_mode(DMA1, DAC_DMA_STREAM);
dma_enable_double_buffer_mode(DMA1, DAC_DMA_STREAM);
dma_enable_stream(DMA1, DAC_DMA_STREAM);
// Configure the DMA engine to stream data from the ADC.
dma_stream_reset(DMA1, ADC_DMA_STREAM);
dma_set_peripheral_address(DMA1, ADC_DMA_STREAM, (intptr_t)&SPI_DR(I2S2_EXT_BASE));
dma_set_memory_address(DMA1, ADC_DMA_STREAM, (intptr_t)adcBuffer[0]);
dma_set_memory_address_1(DMA1, ADC_DMA_STREAM, (intptr_t)adcBuffer[1]);
dma_set_number_of_data(DMA1, ADC_DMA_STREAM, BUFFER_SAMPLES);
dma_channel_select(DMA1, ADC_DMA_STREAM, ADC_DMA_CHANNEL);
dma_set_transfer_mode(DMA1, ADC_DMA_STREAM, DMA_SxCR_DIR_PERIPHERAL_TO_MEM);
dma_set_memory_size(DMA1, ADC_DMA_STREAM, DMA_SxCR_MSIZE_16BIT);
dma_set_peripheral_size(DMA1, ADC_DMA_STREAM, DMA_SxCR_PSIZE_16BIT);
dma_enable_memory_increment_mode(DMA1, ADC_DMA_STREAM);
dma_enable_double_buffer_mode(DMA1, ADC_DMA_STREAM);
dma_enable_stream(DMA1, ADC_DMA_STREAM);
dma_enable_transfer_complete_interrupt(DMA1, ADC_DMA_STREAM);
nvic_enable_irq(NVIC_DMA1_STREAM3_IRQ);
nvic_set_priority(NVIC_DMA1_STREAM3_IRQ, 0x80); // 0 is most urgent
// Start transmitting data
spi_enable_rx_dma(I2S2_EXT_BASE);
spi_enable_tx_dma(SPI2);
}
static int spi_dma_transceive(uint8_t *tx_buf, int tx_len, uint8_t *rx_buf, int rx_len)
#endif
{
/* Check for 0 length in both tx and rx */
if ((rx_len < 1) && (tx_len < 1)) {
/* return -1 as error */
return -1;
}
/* Reset DMA channels*/
dma_channel_reset(DMA1, DMA_CHANNEL4);
dma_channel_reset(DMA1, DMA_CHANNEL5);
/* Reset SPI data and status registers.
* Here we assume that the SPI peripheral is NOT
* busy any longer, i.e. the last activity was verified
* complete elsewhere in the program.
*/
volatile uint8_t temp_data __attribute__ ((unused));
while (SPI_SR(SPI2) & (SPI_SR_RXNE | SPI_SR_OVR)) {
temp_data = SPI_DR(SPI2);
}
/* Reset status flag appropriately (both 0 case caught above) */
transceive_status = NONE;
if (rx_len < 1) {
transceive_status = ONE;
}
if (tx_len < 1) {
transceive_status = ONE;
}
/* Set up rx dma, note it has higher priority to avoid overrun */
if (rx_len > 0) {
dma_set_peripheral_address(DMA1, DMA_CHANNEL4, (uint32_t)&SPI2_DR);
dma_set_memory_address(DMA1, DMA_CHANNEL4, (uint32_t)rx_buf);
dma_set_number_of_data(DMA1, DMA_CHANNEL4, rx_len);
dma_set_read_from_peripheral(DMA1, DMA_CHANNEL4);
dma_enable_memory_increment_mode(DMA1, DMA_CHANNEL4);
#if USE_16BIT_TRANSFERS
dma_set_peripheral_size(DMA1, DMA_CHANNEL4, DMA_CCR_PSIZE_16BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL4, DMA_CCR_MSIZE_16BIT);
#else
dma_set_peripheral_size(DMA1, DMA_CHANNEL4, DMA_CCR_PSIZE_8BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL4, DMA_CCR_MSIZE_8BIT);
#endif
dma_set_priority(DMA1, DMA_CHANNEL4, DMA_CCR_PL_VERY_HIGH);
}
/* Set up tx dma */
if (tx_len > 0) {
dma_set_peripheral_address(DMA1, DMA_CHANNEL5, (uint32_t)&SPI2_DR);
dma_set_memory_address(DMA1, DMA_CHANNEL5, (uint32_t)tx_buf);
dma_set_number_of_data(DMA1, DMA_CHANNEL5, tx_len);
dma_set_read_from_memory(DMA1, DMA_CHANNEL5);
dma_enable_memory_increment_mode(DMA1, DMA_CHANNEL5);
#if USE_16BIT_TRANSFERS
dma_set_peripheral_size(DMA1, DMA_CHANNEL5, DMA_CCR_PSIZE_16BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL5, DMA_CCR_MSIZE_16BIT);
#else
dma_set_peripheral_size(DMA1, DMA_CHANNEL5, DMA_CCR_PSIZE_8BIT);
dma_set_memory_size(DMA1, DMA_CHANNEL5, DMA_CCR_MSIZE_8BIT);
#endif
dma_set_priority(DMA1, DMA_CHANNEL5, DMA_CCR_PL_HIGH);
}
/* Enable dma transfer complete interrupts */
if (rx_len > 0) {
dma_enable_transfer_complete_interrupt(DMA1, DMA_CHANNEL4);
}
if (tx_len > 0) {
dma_enable_transfer_complete_interrupt(DMA1, DMA_CHANNEL5);
}
/* Activate dma channels */
if (rx_len > 0) {
dma_enable_channel(DMA1, DMA_CHANNEL4);
}
if (tx_len > 0) {
dma_enable_channel(DMA1, DMA_CHANNEL5);
}
/* Enable the spi transfer via dma
* This will immediately start the transmission,
* after which when the receive is complete, the
* receive dma will activate
*/
if (rx_len > 0) {
spi_enable_rx_dma(SPI2);
}
if (tx_len > 0) {
spi_enable_tx_dma(SPI2);
}
return 0;
}
int main(void)
{
/* Exactly 20 bytes including '0' at the end.
We want to transfer 32bit * 5 so it should fit */
char s1[20] = "Hello STM MEM2MEM\r\n";
char s2[20];
rcc_clock_setup_in_hse_16mhz_out_72mhz();
gpio_setup();
usart_setup();
gpio_clear(GPIOB, GPIO7); /* LED1 on */
gpio_set(GPIOB, GPIO6); /* LED2 off */
my_usart_print_string(USART1, "s1 ");
my_usart_print_string(USART1, s1);
rcc_peripheral_enable_clock(&RCC_AHBENR, RCC_AHBENR_DMA1EN);
/* MEM2MEM mode for channel 1. */
dma_enable_mem2mem_mode(DMA1, DMA_CHANNEL1);
/* Highest priority. */
dma_set_priority(DMA1, DMA_CHANNEL1, DMA_CCR1_PL_VERY_HIGH);
/* 32Bit wide transfer for source and destination. */
dma_set_memory_size(DMA1, DMA_CHANNEL1, DMA_CCR1_MSIZE_32BIT);
dma_set_peripheral_size(DMA1, DMA_CHANNEL1, DMA_CCR1_PSIZE_32BIT);
/* After each 32Bit we have to increase the addres because we use RAM. */
dma_enable_memory_increment_mode(DMA1, DMA_CHANNEL1);
dma_enable_peripheral_increment_mode(DMA1, DMA_CHANNEL1);
/* We define the source as peripheral. */
dma_set_read_from_peripheral(DMA1, DMA_CHANNEL1);
/* We want to transfer string s1. */
dma_set_peripheral_address(DMA1, DMA_CHANNEL1, (u32) &s1);
/* Destination should be string s2. */
dma_set_memory_address(DMA1, DMA_CHANNEL1, (u32) &s2);
/* Set number of DATA to transfer.
Remember that this means not necessary bytes but MSIZE or PSIZE
depending from your source device. */
dma_set_number_of_data(DMA1, DMA_CHANNEL1, 5);
/* Start DMA transfer. */
dma_enable_channel(DMA1, DMA_CHANNEL1);
/* TODO: write a function to get the interrupt flags. */
while(!(DMA_ISR(DMA1) & 0x0000001))
{
}
dma_disable_channel(DMA1, DMA_CHANNEL1);
/* String s1 should now already be transferred to s2. */
my_usart_print_string(USART1, "s2 ");
my_usart_print_string(USART1, s2);
gpio_clear(GPIOB, GPIO6); /* LED2 on */
while(1); /* Halt. */
return 0;
}