bool Rover::start_command(const AP_Mission::Mission_Command& cmd)
{
// log when new commands start
if (should_log(MASK_LOG_CMD)) {
DataFlash.Log_Write_Mission_Cmd(mission, cmd);
}
// exit immediately if not in AUTO mode
if (control_mode != AUTO) {
return false;
}
gcs_send_text_fmt(MAV_SEVERITY_INFO, "Executing command ID #%i",cmd.id);
// remember the course of our next navigation leg
next_navigation_leg_cd = mission.get_next_ground_course_cd(0);
switch(cmd.id){
case MAV_CMD_NAV_WAYPOINT: // Navigate to Waypoint
do_nav_wp(cmd);
break;
case MAV_CMD_NAV_RETURN_TO_LAUNCH:
do_RTL();
break;
case MAV_CMD_NAV_LOITER_UNLIM: // Loiter indefinitely
do_loiter_unlimited(cmd);
break;
// Conditional commands
case MAV_CMD_CONDITION_DELAY:
do_wait_delay(cmd);
break;
case MAV_CMD_CONDITION_DISTANCE:
do_within_distance(cmd);
break;
// Do commands
case MAV_CMD_DO_CHANGE_SPEED:
do_change_speed(cmd);
break;
case MAV_CMD_DO_SET_HOME:
do_set_home(cmd);
break;
case MAV_CMD_DO_SET_SERVO:
ServoRelayEvents.do_set_servo(cmd.content.servo.channel, cmd.content.servo.pwm);
break;
case MAV_CMD_DO_SET_RELAY:
ServoRelayEvents.do_set_relay(cmd.content.relay.num, cmd.content.relay.state);
break;
case MAV_CMD_DO_REPEAT_SERVO:
ServoRelayEvents.do_repeat_servo(cmd.content.repeat_servo.channel, cmd.content.repeat_servo.pwm,
cmd.content.repeat_servo.repeat_count, cmd.content.repeat_servo.cycle_time * 1000.0f);
break;
case MAV_CMD_DO_REPEAT_RELAY:
ServoRelayEvents.do_repeat_relay(cmd.content.repeat_relay.num, cmd.content.repeat_relay.repeat_count,
cmd.content.repeat_relay.cycle_time * 1000.0f);
break;
#if CAMERA == ENABLED
case MAV_CMD_DO_CONTROL_VIDEO: // Control on-board camera capturing. |Camera ID (-1 for all)| Transmission: 0: disabled, 1: enabled compressed, 2: enabled raw| Transmission mode: 0: video stream, >0: single images every n seconds (decimal)| Recording: 0: disabled, 1: enabled compressed, 2: enabled raw| Empty| Empty| Empty|
break;
case MAV_CMD_DO_DIGICAM_CONFIGURE: // Mission command to configure an on-board camera controller system. |Modes: P, TV, AV, M, Etc| Shutter speed: Divisor number for one second| Aperture: F stop number| ISO number e.g. 80, 100, 200, Etc| Exposure type enumerator| Command Identity| Main engine cut-off time before camera trigger in seconds/10 (0 means no cut-off)|
do_digicam_configure(cmd);
break;
case MAV_CMD_DO_DIGICAM_CONTROL: // Mission command to control an on-board camera controller system. |Session control e.g. show/hide lens| Zoom's absolute position| Zooming step value to offset zoom from the current position| Focus Locking, Unlocking or Re-locking| Shooting Command| Command Identity| Empty|
do_digicam_control(cmd);
break;
case MAV_CMD_DO_SET_CAM_TRIGG_DIST:
camera.set_trigger_distance(cmd.content.cam_trigg_dist.meters);
break;
#endif
#if MOUNT == ENABLED
// Sets the region of interest (ROI) for a sensor set or the
// vehicle itself. This can then be used by the vehicles control
// system to control the vehicle attitude and the attitude of various
// devices such as cameras.
// |Region of interest mode. (see MAV_ROI enum)| Waypoint index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple cameras etc.)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z|
case MAV_CMD_DO_SET_ROI:
if (cmd.content.location.alt == 0 && cmd.content.location.lat == 0 && cmd.content.location.lng == 0) {
// switch off the camera tracking if enabled
if (camera_mount.get_mode() == MAV_MOUNT_MODE_GPS_POINT) {
camera_mount.set_mode_to_default();
}
} else {
// send the command to the camera mount
camera_mount.set_roi_target(cmd.content.location);
}
break;
#endif
case MAV_CMD_DO_SET_REVERSE:
do_set_reverse(cmd);
break;
default:
// return false for unhandled commands
return false;
}
// if we got this far we must have been successful
return true;
}
bool ModeAuto::start_command(const AP_Mission::Mission_Command& cmd)
{
// log when new commands start
if (rover.should_log(MASK_LOG_CMD)) {
rover.logger.Write_Mission_Cmd(mission, cmd);
}
gcs().send_text(MAV_SEVERITY_INFO, "Executing %s(ID=%i)",
cmd.type(), cmd.id);
switch (cmd.id) {
case MAV_CMD_NAV_WAYPOINT: // Navigate to Waypoint
do_nav_wp(cmd, false);
break;
case MAV_CMD_NAV_RETURN_TO_LAUNCH:
do_RTL();
break;
case MAV_CMD_NAV_LOITER_UNLIM: // Loiter indefinitely
case MAV_CMD_NAV_LOITER_TIME: // Loiter for specified time
do_nav_wp(cmd, true);
break;
case MAV_CMD_NAV_SET_YAW_SPEED:
do_nav_set_yaw_speed(cmd);
break;
// Conditional commands
case MAV_CMD_CONDITION_DELAY:
do_wait_delay(cmd);
break;
case MAV_CMD_CONDITION_DISTANCE:
do_within_distance(cmd);
break;
// Do commands
case MAV_CMD_DO_CHANGE_SPEED:
do_change_speed(cmd);
break;
case MAV_CMD_DO_SET_HOME:
do_set_home(cmd);
break;
#if MOUNT == ENABLED
// Sets the region of interest (ROI) for a sensor set or the
// vehicle itself. This can then be used by the vehicles control
// system to control the vehicle attitude and the attitude of various
// devices such as cameras.
// |Region of interest mode. (see MAV_ROI enum)| Waypoint index/ target ID. (see MAV_ROI enum)| ROI index (allows a vehicle to manage multiple cameras etc.)| Empty| x the location of the fixed ROI (see MAV_FRAME)| y| z|
case MAV_CMD_DO_SET_ROI:
if (cmd.content.location.alt == 0 && cmd.content.location.lat == 0 && cmd.content.location.lng == 0) {
// switch off the camera tracking if enabled
if (rover.camera_mount.get_mode() == MAV_MOUNT_MODE_GPS_POINT) {
rover.camera_mount.set_mode_to_default();
}
} else {
// send the command to the camera mount
rover.camera_mount.set_roi_target(cmd.content.location);
}
break;
#endif
case MAV_CMD_DO_SET_REVERSE:
do_set_reverse(cmd);
break;
case MAV_CMD_DO_FENCE_ENABLE:
if (cmd.p1 == 0) { //disable
g2.fence.enable(false);
gcs().send_text(MAV_SEVERITY_INFO, "Fence Disabled");
} else { //enable fence
g2.fence.enable(true);
gcs().send_text(MAV_SEVERITY_INFO, "Fence Enabled");
}
break;
default:
// return false for unhandled commands
return false;
}
// if we got this far we must have been successful
return true;
}
