Exemple #1
0
void app_main()
{
    esp_err_t ret = ESP_OK;
    tcpip_adapter_init();
    esp_event_loop_init(NULL, NULL);

    eth_config_t config = DEFAULT_ETHERNET_PHY_CONFIG;
    /* Set the PHY address in the example configuration */
    config.phy_addr = CONFIG_PHY_ADDRESS;
    config.gpio_config = eth_gpio_config_rmii;
    config.tcpip_input = tcpip_adapter_eth_input;
    config.clock_mode = CONFIG_PHY_CLOCK_MODE;

#ifdef CONFIG_PHY_USE_POWER_PIN
    /* Replace the default 'power enable' function with an example-specific
       one that toggles a power GPIO. */
    config.phy_power_enable = phy_device_power_enable_via_gpio;
#endif

    ret = esp_eth_init(&config);

    if(ret == ESP_OK) {
        esp_eth_enable();
        xTaskCreate(eth_task, "eth_task", 2048, NULL, (tskIDLE_PRIORITY + 2), NULL);
    }

}
Exemple #2
0
//         IP4_ADDR(&esp_ip[TCPIP_ADAPTER_IF_AP].ip, 192, 168 , 31, 100);
//         IP4_ADDR(&esp_ip[TCPIP_ADAPTER_IF_AP].gw, 192, 168 , 31, 1);
//         IP4_ADDR(&esp_ip[TCPIP_ADAPTER_IF_AP].netmask, 255, 255 , 255, 0);
//         ret = sys_sem_new(&api_sync_sem, 0);
//         if (ERR_OK != ret) {
//             ESP_LOGD( "tcpip adatper api sync sem init fail");
//         }
//     }
// }
esp_err_t hal_eht_init()
{
	esp_err_t ret = ESP_OK;
    tcpip_adapter_init();
    
    eth_config_t config = phy_lan8720_default_ethernet_config;
    //config.mac_mode=ETH_MODE_RMII_INT_50MHZ_CLK;
    config.gpio_config = eth_gpio_config_rmii;
    config.tcpip_input = tcpip_adapter_eth_input;

    ret = esp_eth_init(&config);
    return ret;
}
Exemple #3
0
void register_ethernet()
{
    eth_event_group = xEventGroupCreate();
    tcpip_adapter_init();
    ESP_ERROR_CHECK(esp_event_loop_init(eth_event_handler, NULL));

    eth_config_t config = DEFAULT_ETHERNET_PHY_CONFIG;
    config.phy_addr = CONFIG_PHY_ADDRESS;
    config.gpio_config = eth_gpio_config_rmii;
    config.tcpip_input = tcpip_adapter_eth_input;
    config.clock_mode = CONFIG_PHY_CLOCK_MODE;
#ifdef CONFIG_PHY_USE_POWER_PIN
    /* Replace the default 'power enable' function with an example-specific one
     that toggles a power GPIO. */
    config.phy_power_enable = phy_device_power_enable_via_gpio;
#endif

    ESP_ERROR_CHECK(esp_eth_init(&config));

    eth_control_args.control = arg_str1(NULL, NULL, "<start|stop|info>", "Start/Stop Ethernet or Get info of Ethernet");
    eth_control_args.end = arg_end(1);
    const esp_console_cmd_t cmd = {
        .command = "ethernet",
        .help = "Control Ethernet interface",
        .hint = NULL,
        .func = eth_cmd_control,
        .argtable = &eth_control_args
    };
    ESP_ERROR_CHECK(esp_console_cmd_register(&cmd));

    iperf_args.ip = arg_str0("c", "client", "<ip>",
                             "run in client mode, connecting to <host>");
    iperf_args.server = arg_lit0("s", "server", "run in server mode");
    iperf_args.udp = arg_lit0("u", "udp", "use UDP rather than TCP");
    iperf_args.port = arg_int0("p", "port", "<port>",
                               "server port to listen on/connect to");
    iperf_args.interval = arg_int0("i", "interval", "<interval>",
                                   "seconds between periodic bandwidth reports");
    iperf_args.time = arg_int0("t", "time", "<time>", "time in seconds to transmit for (default 10 secs)");
    iperf_args.abort = arg_lit0("a", "abort", "abort running iperf");
    iperf_args.end = arg_end(1);
    const esp_console_cmd_t iperf_cmd = {
        .command = "iperf",
        .help = "iperf command",
        .hint = NULL,
        .func = &eth_cmd_iperf,
        .argtable = &iperf_args
    };
    ESP_ERROR_CHECK(esp_console_cmd_register(&iperf_cmd));
}