/**
* \internal
* \brief Test for external interrupt detection by polling.
*
* This test changes the logic level of PB05 from high to low
* so that the external interrupt channel detects the edge.
*
* Detection is tested for both rising and falling edges.
*
* \param test Current test case.
*/
static void run_extint_polled_mode_test(const struct test_case *test)
{
/* Testing the falling edge detection */
/* Generate falling edge */
port_pin_set_output_level(GPIO_TEST_PIN_EXTINT, false);
/* Wait for the pin level to stabilize */
delay_ms(1);
result = extint_chan_is_detected(EIC_TEST_CHANNEL);
test_assert_true(test, result,
"External interrupt falling edge detection by polling failed");
extint_chan_clear_detected(EIC_TEST_CHANNEL);
/* Testing the rising edge detection */
result = false;
eic_conf.detection_criteria = EXTINT_DETECT_RISING;
extint_chan_set_config(EIC_TEST_CHANNEL, &eic_conf);
/* Generate rising edge */
port_pin_set_output_level(GPIO_TEST_PIN_EXTINT, true);
/* Wait for the pin level to stabilize */
delay_ms(1);
result = extint_chan_is_detected(EIC_TEST_CHANNEL);
test_assert_true(test, result,
"External interrupt rising edge detection by polling failed");
extint_chan_clear_detected(EIC_TEST_CHANNEL);
}
int main(void)
{
system_init();
//! [setup_init]
configure_extint_channel();
//! [setup_init]
//! [main]
while (true) {
//! [main_1]
if (extint_chan_is_detected(BUTTON_0_EIC_LINE)) {
//! [main_1]
//! [main_2]
// Do something in response to EXTINT edge detection
bool button_pin_state = port_pin_get_input_level(BUTTON_0_PIN);
port_pin_set_output_level(LED_0_PIN, button_pin_state);
//! [main_2]
//! [main_3]
extint_chan_clear_detected(BUTTON_0_EIC_LINE);
//! [main_3]
}
}
//! [main]
}
int main(void)
{
system_init();
configure_usart();
configure_usart_callbacks();
struct port_config pin_conf;
port_get_config_defaults(&pin_conf);
/* Configure LEDs as outputs, turn them off */
pin_conf.direction = PORT_PIN_DIR_OUTPUT;
port_pin_set_config(LED_1_PIN, &pin_conf);
port_pin_set_output_level(LED_1_PIN, LED_1_INACTIVE);
/* Set buttons as inputs */
pin_conf.direction = PORT_PIN_DIR_INPUT;
pin_conf.input_pull = PORT_PIN_PULL_UP;
port_pin_set_config(BUTTON_1_PIN, &pin_conf);
#if USE_EIC == true
configure_extint();
#endif
#if USE_INTERRUPTS == true
# if USE_EIC == false
configure_systick_handler();
# else
configure_eic_callback();
# endif
system_interrupt_enable_global();
uint16_t temp;
while (true) {
/* Do nothing - use interrupts */
//if (usart_read_wait(&usart_instance, &temp) == STATUS_OK)
//{
//while (usart_write_wait(&usart_instance, temp) != STATUS_OK);
//}
usart_read_buffer_job(&usart_instance, (uint8_t *)rx_buffer, 1);
//sleepmgr_sleep(SLEEPMGR_STANDBY);
}
#else
# if USE_EIC == false
while (true) {
update_led_state();
}
# else
while (true) {
if (extint_chan_is_detected(BUTTON_1_EIC_LINE)) {
extint_chan_clear_detected(BUTTON_1_EIC_LINE);
update_led_state();
}
}
# endif
#endif
}
/** Handler for the EXTINT hardware module interrupt. */
void EIC_Handler(void)
{
/* Find any triggered channels, run associated callback handlers */
for (uint8_t i = 0; i < EIC_NUMBER_OF_INTERRUPTS ; i++) {
if (extint_chan_is_detected(i)) {
/* Clear flag */
extint_chan_clear_detected(i);
/* Find any associated callback entries in the callback table */
if (_extint_dev.callbacks[i] != NULL) {
/* Run the registered callback */
_extint_dev.callbacks[i]();
}
}
}
}
/**
* \brief Initializes and enables interrupt pin change
*/
static void ui_enable_asynchronous_interrupt(void)
{
/* Initialize EIC for button wakeup */
struct extint_chan_conf eint_chan_conf;
extint_chan_get_config_defaults(&eint_chan_conf);
eint_chan_conf.gpio_pin = BUTTON_0_EIC_PIN;
eint_chan_conf.gpio_pin_mux = BUTTON_0_EIC_MUX;
eint_chan_conf.detection_criteria = EXTINT_DETECT_FALLING;
eint_chan_conf.filter_input_signal = true;
extint_chan_set_config(BUTTON_0_EIC_LINE, &eint_chan_conf);
extint_register_callback(UI_WAKEUP_HANDLER,
BUTTON_0_EIC_LINE,
EXTINT_CALLBACK_TYPE_DETECT);
extint_chan_clear_detected(BUTTON_0_EIC_LINE);
extint_chan_enable_callback(BUTTON_0_EIC_LINE,
EXTINT_CALLBACK_TYPE_DETECT);
}
void gpio_irq(void)
{
uint32_t current_channel;
uint32_t mask;
gpio_irq_event event;
PortGroup *port_base;
for (current_channel = 0; current_channel < EIC_NUMBER_OF_INTERRUPTS ; current_channel++) {
if (extint_chan_is_detected(current_channel)) {
extint_chan_clear_detected(current_channel);
port_base = (PortGroup*)port_get_group_from_gpio_pin(ext_int_pins[current_channel]);
mask = gpio_set(ext_int_pins[current_channel]);
if ((port_base->IN.reg & mask) != 0) {
event = IRQ_RISE;
} else {
event = IRQ_FALL;
}
if(irq_handler) {
irq_handler(channel_ids[current_channel], event);
}
}
}
}
int main(void)
{
system_init();
#if USE_EIC == true
configure_extint();
#endif
#if USE_INTERRUPTS == true
# if USE_EIC == false
configure_systick_handler();
# else
configure_eic_callback();
# endif
system_interrupt_enable_global();
while (true) {
/* Do nothing - use interrupts */
}
#else
# if USE_EIC == false
while (true) {
update_led_state();
}
# else
while (true) {
if (extint_chan_is_detected(BUTTON_0_EIC_LINE)) {
extint_chan_clear_detected(BUTTON_0_EIC_LINE);
update_led_state();
}
}
# endif
#endif
}
void interruptValueInitializzation(void) {
TCA6416a_input_ports_values(&portsValue);
// clear Interrupt
extint_chan_clear_detected(SME_INT_IOEXT_EIC_LINE);
}