/*
* Transfer the firmware image to RAM for execution by the microcontroller.
*
* Architecturally, the DMA engine is bidirectional, and can potentially even
* transfer between GTT locations. This functionality is left out of the API
* for now as there is no need for it.
*
* Note that GuC needs the CSS header plus uKernel code to be copied by the
* DMA engine in one operation, whereas the RSA signature is loaded via MMIO.
*/
static int guc_ucode_xfer_dma(struct drm_i915_private *dev_priv,
struct i915_vma *vma)
{
struct intel_uc_fw *guc_fw = &dev_priv->guc.fw;
unsigned long offset;
struct sg_table *sg = vma->pages;
u32 status, rsa[UOS_RSA_SCRATCH_MAX_COUNT];
int i, ret = 0;
/* where RSA signature starts */
offset = guc_fw->rsa_offset;
/* Copy RSA signature from the fw image to HW for verification */
sg_pcopy_to_buffer(sg->sgl, sg->nents, rsa, sizeof(rsa), offset);
for (i = 0; i < UOS_RSA_SCRATCH_MAX_COUNT; i++)
I915_WRITE(UOS_RSA_SCRATCH(i), rsa[i]);
/* The header plus uCode will be copied to WOPCM via DMA, excluding any
* other components */
I915_WRITE(DMA_COPY_SIZE, guc_fw->header_size + guc_fw->ucode_size);
/* Set the source address for the new blob */
offset = guc_ggtt_offset(vma) + guc_fw->header_offset;
I915_WRITE(DMA_ADDR_0_LOW, lower_32_bits(offset));
I915_WRITE(DMA_ADDR_0_HIGH, upper_32_bits(offset) & 0xFFFF);
/*
* Set the DMA destination. Current uCode expects the code to be
* loaded at 8k; locations below this are used for the stack.
*/
I915_WRITE(DMA_ADDR_1_LOW, 0x2000);
I915_WRITE(DMA_ADDR_1_HIGH, DMA_ADDRESS_SPACE_WOPCM);
/* Finally start the DMA */
I915_WRITE(DMA_CTRL, _MASKED_BIT_ENABLE(UOS_MOVE | START_DMA));
/*
* Wait for the DMA to complete & the GuC to start up.
* NB: Docs recommend not using the interrupt for completion.
* Measurements indicate this should take no more than 20ms, so a
* timeout here indicates that the GuC has failed and is unusable.
* (Higher levels of the driver will attempt to fall back to
* execlist mode if this happens.)
*/
ret = wait_for(guc_ucode_response(dev_priv, &status), 100);
DRM_DEBUG_DRIVER("DMA status 0x%x, GuC status 0x%x\n",
I915_READ(DMA_CTRL), status);
if ((status & GS_BOOTROM_MASK) == GS_BOOTROM_RSA_FAILED) {
DRM_ERROR("GuC firmware signature verification failed\n");
ret = -ENOEXEC;
}
DRM_DEBUG_DRIVER("returning %d\n", ret);
return ret;
}
/*
* Initialise the GuC parameter block before starting the firmware
* transfer. These parameters are read by the firmware on startup
* and cannot be changed thereafter.
*/
void intel_guc_init_params(struct intel_guc *guc)
{
struct drm_i915_private *dev_priv = guc_to_i915(guc);
u32 params[GUC_CTL_MAX_DWORDS];
int i;
memset(params, 0, sizeof(params));
params[GUC_CTL_DEVICE_INFO] |=
(get_gt_type(dev_priv) << GUC_CTL_GT_TYPE_SHIFT) |
(get_core_family(dev_priv) << GUC_CTL_CORE_FAMILY_SHIFT);
/*
* GuC ARAT increment is 10 ns. GuC default scheduler quantum is one
* second. This ARAR is calculated by:
* Scheduler-Quantum-in-ns / ARAT-increment-in-ns = 1000000000 / 10
*/
params[GUC_CTL_ARAT_HIGH] = 0;
params[GUC_CTL_ARAT_LOW] = 100000000;
params[GUC_CTL_WA] |= GUC_CTL_WA_UK_BY_DRIVER;
params[GUC_CTL_FEATURE] |= GUC_CTL_DISABLE_SCHEDULER |
GUC_CTL_VCS2_ENABLED;
params[GUC_CTL_LOG_PARAMS] = guc->log.flags;
if (i915_modparams.guc_log_level >= 0) {
params[GUC_CTL_DEBUG] =
i915_modparams.guc_log_level << GUC_LOG_VERBOSITY_SHIFT;
} else {
params[GUC_CTL_DEBUG] = GUC_LOG_DISABLED;
}
/* If GuC submission is enabled, set up additional parameters here */
if (i915_modparams.enable_guc_submission) {
u32 ads = guc_ggtt_offset(guc->ads_vma) >> PAGE_SHIFT;
u32 pgs = guc_ggtt_offset(dev_priv->guc.stage_desc_pool);
u32 ctx_in_16 = GUC_MAX_STAGE_DESCRIPTORS / 16;
params[GUC_CTL_DEBUG] |= ads << GUC_ADS_ADDR_SHIFT;
params[GUC_CTL_DEBUG] |= GUC_ADS_ENABLED;
pgs >>= PAGE_SHIFT;
params[GUC_CTL_CTXINFO] = (pgs << GUC_CTL_BASE_ADDR_SHIFT) |
(ctx_in_16 << GUC_CTL_CTXNUM_IN16_SHIFT);
params[GUC_CTL_FEATURE] |= GUC_CTL_KERNEL_SUBMISSIONS;
/* Unmask this bit to enable the GuC's internal scheduler */
params[GUC_CTL_FEATURE] &= ~GUC_CTL_DISABLE_SCHEDULER;
}
/*
* Transfer the firmware image to RAM for execution by the microcontroller.
*
* Architecturally, the DMA engine is bidirectional, and can potentially even
* transfer between GTT locations. This functionality is left out of the API
* for now as there is no need for it.
*/
static int guc_xfer_ucode(struct intel_guc *guc, struct i915_vma *vma)
{
struct drm_i915_private *dev_priv = guc_to_i915(guc);
struct intel_uc_fw *guc_fw = &guc->fw;
unsigned long offset;
u32 status;
int ret;
/*
* The header plus uCode will be copied to WOPCM via DMA, excluding any
* other components
*/
I915_WRITE(DMA_COPY_SIZE, guc_fw->header_size + guc_fw->ucode_size);
/* Set the source address for the new blob */
offset = guc_ggtt_offset(vma) + guc_fw->header_offset;
I915_WRITE(DMA_ADDR_0_LOW, lower_32_bits(offset));
I915_WRITE(DMA_ADDR_0_HIGH, upper_32_bits(offset) & 0xFFFF);
/*
* Set the DMA destination. Current uCode expects the code to be
* loaded at 8k; locations below this are used for the stack.
*/
I915_WRITE(DMA_ADDR_1_LOW, 0x2000);
I915_WRITE(DMA_ADDR_1_HIGH, DMA_ADDRESS_SPACE_WOPCM);
/* Finally start the DMA */
I915_WRITE(DMA_CTRL, _MASKED_BIT_ENABLE(UOS_MOVE | START_DMA));
/* Wait for DMA to finish */
ret = __intel_wait_for_register_fw(dev_priv, DMA_CTRL, START_DMA, 0,
2, 100, &status);
DRM_DEBUG_DRIVER("GuC DMA status %#x\n", status);
return ret;
}
