void __init config_BSP(char *commandp, int size)
{
#if defined(CONFIG_NETtel) || \
defined(CONFIG_SECUREEDGEMP3) || defined(CONFIG_CLEOPATRA)
/* Copy command line from FLASH to local buffer... */
memcpy(commandp, (char *) 0xf0004000, size);
commandp[size-1] = 0;
#endif
mach_sched_init = hw_timer_init;
/* Only support the external interrupts on their primary level */
mcf_mapirq2imr(25, MCFINTC_EINT1);
mcf_mapirq2imr(27, MCFINTC_EINT3);
mcf_mapirq2imr(29, MCFINTC_EINT5);
mcf_mapirq2imr(31, MCFINTC_EINT7);
#ifdef CONFIG_BDM_DISABLE
/*
* Disable the BDM clocking. This also turns off most of the rest of
* the BDM device. This is good for EMC reasons. This option is not
* incompatible with the memory protection option.
*/
wdebug(MCFDEBUG_CSR, MCFDEBUG_CSR_PSTCLK);
#endif
}
void __init config_BSP(char *commandp, int size)
{
mach_sched_init = hw_timer_init;
/* Only support the external interrupts on their primary level */
mcf_mapirq2imr(25, MCFINTC_EINT1);
mcf_mapirq2imr(27, MCFINTC_EINT3);
mcf_mapirq2imr(29, MCFINTC_EINT5);
mcf_mapirq2imr(31, MCFINTC_EINT7);
}
static void __init m5206e_uart_init_line(int line, int irq)
{
if (line == 0) {
writel(MCFSIM_ICR_LEVEL6 | MCFSIM_ICR_PRI1, MCF_MBAR + MCFSIM_UART1ICR);
writeb(irq, MCFUART_BASE1 + MCFUART_UIVR);
mcf_mapirq2imr(irq, MCFINTC_UART0);
} else if (line == 1) {
writel(MCFSIM_ICR_LEVEL6 | MCFSIM_ICR_PRI2, MCF_MBAR + MCFSIM_UART2ICR);
writeb(irq, MCFUART_BASE2 + MCFUART_UIVR);
mcf_mapirq2imr(irq, MCFINTC_UART1);
}
}
static void __init m5206e_timers_init(void)
{
/* Timer1 is always used as system timer */
writeb(MCFSIM_ICR_AUTOVEC | MCFSIM_ICR_LEVEL6 | MCFSIM_ICR_PRI3,
MCF_MBAR + MCFSIM_TIMER1ICR);
mcf_mapirq2imr(MCF_IRQ_TIMER, MCFINTC_TIMER1);
#ifdef CONFIG_HIGHPROFILE
/* Timer2 is to be used as a high speed profile timer */
writeb(MCFSIM_ICR_AUTOVEC | MCFSIM_ICR_LEVEL7 | MCFSIM_ICR_PRI3,
MCF_MBAR + MCFSIM_TIMER2ICR);
mcf_mapirq2imr(MCF_IRQ_PROFILER, MCFINTC_TIMER2);
#endif
}
static void __init mcf_uart_set_irq(void)
{
#ifdef MCFUART_UIVR
writeb(MCFSIM_ICR_LEVEL6 | MCFSIM_ICR_PRI1, MCF_MBAR + MCFSIM_UART1ICR);
writeb(MCF_IRQ_UART0, MCFUART_BASE0 + MCFUART_UIVR);
mcf_mapirq2imr(MCF_IRQ_UART0, MCFINTC_UART0);
writeb(MCFSIM_ICR_LEVEL6 | MCFSIM_ICR_PRI2, MCF_MBAR + MCFSIM_UART2ICR);
writeb(MCF_IRQ_UART1, MCFUART_BASE1 + MCFUART_UIVR);
mcf_mapirq2imr(MCF_IRQ_UART1, MCFINTC_UART1);
#endif
}
void __init config_BSP(char *commandp, int size)
{
#if defined(CONFIG_NETtel)
/* Copy command line from FLASH to local buffer... */
memcpy(commandp, (char *) 0xf0004000, size);
commandp[size-1] = 0;
#endif /* CONFIG_NETtel */
mach_sched_init = hw_timer_init;
/* Only support the external interrupts on their primary level */
mcf_mapirq2imr(25, MCFINTC_EINT1);
mcf_mapirq2imr(28, MCFINTC_EINT4);
mcf_mapirq2imr(31, MCFINTC_EINT7);
}
static void init_timer_irq(void)
{
#ifdef MCFSIM_ICR_AUTOVEC
/* Timer1 is always used as system timer */
writeb(MCFSIM_ICR_AUTOVEC | MCFSIM_ICR_LEVEL6 | MCFSIM_ICR_PRI3,
MCFSIM_TIMER1ICR);
mcf_mapirq2imr(MCF_IRQ_TIMER, MCFINTC_TIMER1);
#ifdef CONFIG_HIGHPROFILE
/* Timer2 is to be used as a high speed profile timer */
writeb(MCFSIM_ICR_AUTOVEC | MCFSIM_ICR_LEVEL7 | MCFSIM_ICR_PRI3,
MCFSIM_TIMER2ICR);
mcf_mapirq2imr(MCF_IRQ_PROFILER, MCFINTC_TIMER2);
#endif
#endif /* MCFSIM_ICR_AUTOVEC */
}
static void __init m5249_qspi_init(void)
{
/* QSPI irq setup */
writeb(MCFSIM_ICR_AUTOVEC | MCFSIM_ICR_LEVEL4 | MCFSIM_ICR_PRI0,
MCF_MBAR + MCFSIM_QSPIICR);
mcf_mapirq2imr(MCF_IRQ_QSPI, MCFINTC_QSPI);
}
static void __init m5407_i2c_init(void)
{
#if IS_ENABLED(CONFIG_I2C_IMX)
writeb(MCFSIM_ICR_AUTOVEC | MCFSIM_ICR_LEVEL5 | MCFSIM_ICR_PRI0,
MCFSIM_I2CICR);
mcf_mapirq2imr(MCF_IRQ_I2C0, MCFINTC_I2C);
#endif /* IS_ENABLED(CONFIG_I2C_IMX) */
}
static void __init m5249_qspi_init(void)
{
#if IS_ENABLED(CONFIG_SPI_COLDFIRE_QSPI)
/* QSPI irq setup */
writeb(MCFSIM_ICR_AUTOVEC | MCFSIM_ICR_LEVEL4 | MCFSIM_ICR_PRI0,
MCFSIM_QSPIICR);
mcf_mapirq2imr(MCF_IRQ_QSPI, MCFINTC_QSPI);
#endif /* IS_ENABLED(CONFIG_SPI_COLDFIRE_QSPI) */
}
static void __init m525x_qspi_init(void)
{
#if IS_ENABLED(CONFIG_SPI_COLDFIRE_QSPI)
/* set the GPIO function for the qspi cs gpios */
/* FIXME: replace with pinmux/pinctl support */
u32 f = readl(MCFSIM2_GPIOFUNC);
f |= (1 << MCFQSPI_CS2) | (1 << MCFQSPI_CS1) | (1 << MCFQSPI_CS0);
writel(f, MCFSIM2_GPIOFUNC);
/* QSPI irq setup */
writeb(MCFSIM_ICR_AUTOVEC | MCFSIM_ICR_LEVEL4 | MCFSIM_ICR_PRI0,
MCFSIM_QSPIICR);
mcf_mapirq2imr(MCF_IRQ_QSPI, MCFINTC_QSPI);
#endif /* IS_ENABLED(CONFIG_SPI_COLDFIRE_QSPI) */
}
static void __init m525x_i2c_init(void)
{
#if IS_ENABLED(CONFIG_I2C_COLDFIRE)
u32 r;
/* first I2C controller uses regular irq setup */
writeb(MCFSIM_ICR_AUTOVEC | MCFSIM_ICR_LEVEL5 | MCFSIM_ICR_PRI0,
MCFSIM_I2CICR);
mcf_mapirq2imr(MCF_IRQ_I2C0, MCFINTC_I2C);
/* second I2C controller is completely different */
r = readl(MCFINTC2_INTPRI_REG(MCF_IRQ_I2C1));
r &= ~MCFINTC2_INTPRI_BITS(0xf, MCF_IRQ_I2C1);
r |= MCFINTC2_INTPRI_BITS(0x5, MCF_IRQ_I2C1);
writel(r, MCFINTC2_INTPRI_REG(MCF_IRQ_I2C1));
#endif /* IS_ENABLED(CONFIG_I2C_COLDFIRE) */
}
