//*****************************************************************************
//
//! bootmain
//!
//! \param None
//!
//! \return uint8
//!
//! \brief : all the board peripherals will be initialized here .
// debug console will also be initialized for debugging info.
//
//*****************************************************************************
void bootMain()
{
//int status;
//void (*p)(void);
//
// Board Initialization .
//
gpio_init();
#ifdef RUN_APP
misc_init_r(); //currently blank.
#endif
//init drivers.
// init_SYSLeds();
// DispatcherUARTConfigure();
// init_console(); //
init_wifiDriver();
turnLedOn(SYSLED1); //to indicate that we are active and initiated WLAN successfully
#ifdef RUN_APP
misc_init_s(); //currently blank.
#endif
//unsolicicted_events_timer_init(); // not required in the newer service packs of cc3000.
//__bis_SR_register(GIE);
#ifdef RUN_APP
appMain();
#else
systest_app();
#endif
while(1)
{
//__bis_SR_register(LPM2_bits + GIE);
toggleLed(SYSLED1);
__no_operation();
__delay_cycles(12000000);
#ifdef SERVICE_PACK_OLDER_THAN_
//hci_unsolicited_event_handler(); // ---- will call the function -------> CC3000_AsyncEventCallback() { CC3000.c}
#endif
//status=wlan_ioctl_statusget();
}
}
void board_init_r(gd_t *id, ulong dest_addr)
{
ulong malloc_start;
#if !defined(CONFIG_SYS_NO_FLASH)
ulong flash_size;
#endif
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
bootstage_mark_name(BOOTSTAGE_ID_START_UBOOT_R, "board_init_r");
monitor_flash_len = (ulong)&__rel_dyn_end - (ulong)_start;
/* Enable caches */
enable_caches();
debug("monitor flash len: %08lX\n", monitor_flash_len);
board_init(); /* Setup chipselects */
/*
* TODO: printing of the clock inforamtion of the board is now
* implemented as part of bdinfo command. Currently only support for
* davinci SOC's is added. Remove this check once all the board
* implement this.
*/
#ifdef CONFIG_CLOCKS
set_cpu_clk_info(); /* Setup clock information */
#endif
serial_initialize();
debug("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
#ifdef CONFIG_LOGBUFFER
logbuff_init_ptrs();
#endif
#ifdef CONFIG_POST
post_output_backlog();
#endif
/* The Malloc area is immediately below the monitor copy in DRAM */
malloc_start = dest_addr - TOTAL_MALLOC_LEN;
mem_malloc_init (malloc_start, TOTAL_MALLOC_LEN);
#ifdef CONFIG_ARCH_EARLY_INIT_R
arch_early_init_r();
#endif
power_init_board();
#if !defined(CONFIG_SYS_NO_FLASH)
puts("Flash: ");
flash_size = flash_init();
if (flash_size > 0) {
# ifdef CONFIG_SYS_FLASH_CHECKSUM
print_size(flash_size, "");
/*
* Compute and print flash CRC if flashchecksum is set to 'y'
*
* NOTE: Maybe we should add some WATCHDOG_RESET()? XXX
*/
if (getenv_yesno("flashchecksum") == 1) {
printf(" CRC: %08X", crc32(0,
(const unsigned char *) CONFIG_SYS_FLASH_BASE,
flash_size));
}
putc('\n');
# else /* !CONFIG_SYS_FLASH_CHECKSUM */
print_size(flash_size, "\n");
# endif /* CONFIG_SYS_FLASH_CHECKSUM */
} else {
puts(failed);
hang();
}
#endif
#if defined(CONFIG_CMD_NAND)
puts("NAND: ");
nand_init(); /* go init the NAND */
#endif
#if defined(CONFIG_CMD_ONENAND)
onenand_init();
#endif
#ifdef CONFIG_GENERIC_MMC
puts("MMC: ");
mmc_initialize(gd->bd);
#endif
#ifdef CONFIG_CMD_SCSI
puts("SCSI: ");
scsi_init();
#endif
#ifdef CONFIG_HAS_DATAFLASH
AT91F_DataflashInit();
dataflash_print_info();
#endif
/* initialize environment */
if (should_load_env())
env_relocate();
else
set_default_env(NULL);
#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI)
arm_pci_init();
#endif
stdio_init(); /* get the devices list going. */
jumptable_init();
#if defined(CONFIG_API)
/* Initialize API */
api_init();
#endif
console_init_r(); /* fully init console as a device */
#ifdef CONFIG_DISPLAY_BOARDINFO_LATE
# ifdef CONFIG_OF_CONTROL
/* Put this here so it appears on the LCD, now it is ready */
display_fdt_model(gd->fdt_blob);
# else
checkboard();
# endif
#endif
#if defined(CONFIG_ARCH_MISC_INIT)
/* miscellaneous arch dependent initialisations */
arch_misc_init();
#endif
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
/* set up exceptions */
interrupt_init();
/* enable exceptions */
enable_interrupts();
/* Initialize from environment */
load_addr = getenv_ulong("loadaddr", 16, load_addr);
#ifdef CONFIG_BOARD_LATE_INIT
board_late_init();
#endif
#ifdef CONFIG_FASTBOOT
fastboot_setup();
#endif
#ifdef CONFIG_BITBANGMII
bb_miiphy_init();
#endif
#if defined(CONFIG_CMD_NET)
puts("Net: ");
eth_initialize(gd->bd);
#if defined(CONFIG_RESET_PHY_R)
debug("Reset Ethernet PHY\n");
reset_phy();
#endif
#endif
#ifdef CONFIG_POST
post_run(NULL, POST_RAM | post_bootmode_get(0));
#endif
#if defined(CONFIG_PRAM) || defined(CONFIG_LOGBUFFER)
/*
* Export available size of memory for Linux,
* taking into account the protected RAM at top of memory
*/
{
ulong pram = 0;
uchar memsz[32];
#ifdef CONFIG_PRAM
pram = getenv_ulong("pram", 10, CONFIG_PRAM);
#endif
#ifdef CONFIG_LOGBUFFER
#ifndef CONFIG_ALT_LB_ADDR
/* Also take the logbuffer into account (pram is in kB) */
pram += (LOGBUFF_LEN + LOGBUFF_OVERHEAD) / 1024;
#endif
#endif
sprintf((char *)memsz, "%ldk", (gd->ram_size / 1024) - pram);
setenv("mem", (char *)memsz);
}
#endif
#ifdef CONFIG_FASTBOOT
check_fastboot();
#endif
/* main_loop() can return to retry autoboot, if so just run it again. */
for (;;) {
main_loop();
}
/* NOTREACHED - no way out of command loop except booting */
}
void start_armboot (void)
{
init_fnc_t **init_fnc_ptr;
char *s;
int mmc_exist = 0;
#if defined(CONFIG_VFD) || defined(CONFIG_LCD)
unsigned long addr;
#endif
/* Pointer is writable since we allocated a register for it */
gd = (gd_t*)(_armboot_start - CONFIG_SYS_MALLOC_LEN - sizeof(gd_t));
/* compiler optimization barrier needed for GCC >= 3.4 */
__asm__ __volatile__("": : :"memory");
memset ((void*)gd, 0, sizeof (gd_t));
gd->bd = (bd_t*)((char*)gd - sizeof(bd_t));
memset (gd->bd, 0, sizeof (bd_t));
// gd->flags |= GD_FLG_RELOC;
monitor_flash_len = _bss_start - _armboot_start;
for (init_fnc_ptr = init_sequence; *init_fnc_ptr; ++init_fnc_ptr) {
if ((*init_fnc_ptr)() != 0) {
hang ();
}
}
/* armboot_start is defined in the board-specific linker script */
mem_malloc_init (_armboot_start - CONFIG_SYS_MALLOC_LEN,
CONFIG_SYS_MALLOC_LEN);
#ifndef CONFIG_SYS_NO_FLASH
/* configure available FLASH banks */
display_flash_config (flash_init ());
#endif /* CONFIG_SYS_NO_FLASH */
#ifdef CONFIG_VFD
# ifndef PAGE_SIZE
# define PAGE_SIZE 4096
# endif
/*
* reserve memory for VFD display (always full pages)
*/
/* bss_end is defined in the board-specific linker script */
addr = (_bss_end + (PAGE_SIZE - 1)) & ~(PAGE_SIZE - 1);
vfd_setmem (addr);
gd->fb_base = addr;
#endif /* CONFIG_VFD */
#ifdef CONFIG_LCD
/* board init may have inited fb_base */
if (!gd->fb_base) {
# ifndef PAGE_SIZE
# define PAGE_SIZE 4096
# endif
/*
* reserve memory for LCD display (always full pages)
*/
/* bss_end is defined in the board-specific linker script */
addr = (_bss_end + (PAGE_SIZE - 1)) & ~(PAGE_SIZE - 1);
lcd_setmem (addr);
gd->fb_base = addr;
}
#endif /* CONFIG_LCD */
#if defined(CONFIG_CMD_NAND)
puts ("NAND: ");
nand_init(); /* go init the NAND */
#endif
#if defined(CONFIG_CMD_ONENAND)
onenand_init();
#endif
#ifdef CONFIG_GENERIC_MMC
puts ("MMC: ");
mmc_exist = mmc_initialize (gd->bd);
if (mmc_exist != 0)
{
puts ("0 MB\n");
}
#endif
#ifdef CONFIG_HAS_DATAFLASH
AT91F_DataflashInit();
dataflash_print_info();
#endif
/* initialize environment */
env_relocate ();
#ifdef CONFIG_VFD
/* must do this after the framebuffer is allocated */
drv_vfd_init();
#endif /* CONFIG_VFD */
#ifdef CONFIG_SERIAL_MULTI
serial_initialize();
#endif
/* IP Address */
gd->bd->bi_ip_addr = getenv_IPaddr ("ipaddr");
stdio_init (); /* get the devices list going. */
jumptable_init ();
#if defined(CONFIG_API)
/* Initialize API */
api_init ();
#endif
console_init_r (); /* fully init console as a device */
#if defined(CONFIG_ARCH_MISC_INIT)
/* miscellaneous arch dependent initialisations */
arch_misc_init ();
#endif
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r ();
#endif
/* enable exceptions */
enable_interrupts ();
/* Perform network card initialisation if necessary */
#ifdef CONFIG_DRIVER_TI_EMAC
/* XXX: this needs to be moved to board init */
extern void davinci_eth_set_mac_addr (const u_int8_t *addr);
if (getenv ("ethaddr")) {
uchar enetaddr[6];
eth_getenv_enetaddr("ethaddr", enetaddr);
davinci_eth_set_mac_addr(enetaddr);
}
#endif
#if defined(CONFIG_DRIVER_SMC91111) || defined (CONFIG_DRIVER_LAN91C96)
/* XXX: this needs to be moved to board init */
if (getenv ("ethaddr")) {
uchar enetaddr[6];
eth_getenv_enetaddr("ethaddr", enetaddr);
smc_set_mac_addr(enetaddr);
}
#endif /* CONFIG_DRIVER_SMC91111 || CONFIG_DRIVER_LAN91C96 */
/* Initialize from environment */
if ((s = getenv ("loadaddr")) != NULL) {
load_addr = simple_strtoul (s, NULL, 16);
}
#if defined(CONFIG_CMD_NET)
if ((s = getenv ("bootfile")) != NULL) {
copy_filename (BootFile, s, sizeof (BootFile));
}
#endif
#ifdef BOARD_LATE_INIT
board_late_init ();
#endif
#ifdef CONFIG_BITBANGMII
bb_miiphy_init();
#endif
#if defined(CONFIG_CMD_NET)
#if defined(CONFIG_NET_MULTI)
puts ("Net: ");
#endif
eth_initialize(gd->bd);
#if defined(CONFIG_RESET_PHY_R)
debug ("Reset Ethernet PHY\n");
reset_phy();
#endif
#endif
/* main_loop() can return to retry autoboot, if so just run it again. */
for (;;) {
main_loop ();
}
/* NOTREACHED - no way out of command loop except booting */
}
void board_init_r(gd_t *id, ulong dest_addr)
{
char *s;
bd_t *bd;
ulong malloc_start;
#if !defined(CONFIG_SYS_NO_FLASH)
ulong flash_size;
#endif
gd = id;
bd = gd->bd;
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
monitor_flash_len = _end_ofs;
/*
* Enable D$:
* I$, if needed, must be already enabled in start.S
*/
dcache_enable();
debug("monitor flash len: %08lX\n", monitor_flash_len);
board_init(); /* Setup chipselects */
#ifdef CONFIG_SERIAL_MULTI
serial_initialize();
#endif
debug("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
#ifdef CONFIG_LOGBUFFER
logbuff_init_ptrs();
#endif
#ifdef CONFIG_POST
post_output_backlog();
#endif
/* The Malloc area is immediately below the monitor copy in DRAM */
malloc_start = dest_addr - TOTAL_MALLOC_LEN;
mem_malloc_init (malloc_start, TOTAL_MALLOC_LEN);
#if !defined(CONFIG_SYS_NO_FLASH)
puts("Flash: ");
flash_size = flash_init();
if (flash_size > 0) {
# ifdef CONFIG_SYS_FLASH_CHECKSUM
print_size(flash_size, "");
/*
* Compute and print flash CRC if flashchecksum is set to 'y'
*
* NOTE: Maybe we should add some WATCHDOG_RESET()? XXX
*/
s = getenv("flashchecksum");
if (s && (*s == 'y')) {
printf(" CRC: %08X", crc32(0,
(const unsigned char *) CONFIG_SYS_FLASH_BASE,
flash_size));
}
putc('\n');
# else /* !CONFIG_SYS_FLASH_CHECKSUM */
print_size(flash_size, "\n");
# endif /* CONFIG_SYS_FLASH_CHECKSUM */
} else {
puts(failed);
hang();
}
#endif
#if defined(CONFIG_CMD_NAND)
puts("NAND: ");
nand_init(); /* go init the NAND */
#endif
#if defined(CONFIG_CMD_ONENAND)
onenand_init();
#endif
#ifdef CONFIG_GENERIC_MMC
puts("MMC: ");
mmc_initialize(bd);
#endif
#ifdef CONFIG_HAS_DATAFLASH
AT91F_DataflashInit();
dataflash_print_info();
#endif
/* initialize environment */
env_relocate();
#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI)
arm_pci_init();
#endif
/* IP Address */
gd->bd->bi_ip_addr = getenv_IPaddr("ipaddr");
stdio_init(); /* get the devices list going. */
jumptable_init();
#if defined(CONFIG_API)
/* Initialize API */
api_init();
#endif
console_init_r(); /* fully init console as a device */
#if defined(CONFIG_ARCH_MISC_INIT)
/* miscellaneous arch dependent initialisations */
arch_misc_init();
#endif
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
/* set up exceptions */
interrupt_init();
/* enable exceptions */
enable_interrupts();
/* Perform network card initialisation if necessary */
#if defined(CONFIG_DRIVER_SMC91111) || defined (CONFIG_DRIVER_LAN91C96)
/* XXX: this needs to be moved to board init */
if (getenv("ethaddr")) {
uchar enetaddr[6];
eth_getenv_enetaddr("ethaddr", enetaddr);
smc_set_mac_addr(enetaddr);
}
#endif /* CONFIG_DRIVER_SMC91111 || CONFIG_DRIVER_LAN91C96 */
/* Initialize from environment */
s = getenv("loadaddr");
if (s != NULL)
load_addr = simple_strtoul(s, NULL, 16);
#if defined(CONFIG_CMD_NET)
s = getenv("bootfile");
if (s != NULL)
copy_filename(BootFile, s, sizeof(BootFile));
#endif
#ifdef BOARD_LATE_INIT
board_late_init();
#endif
#ifdef CONFIG_BITBANGMII
bb_miiphy_init();
#endif
#if defined(CONFIG_CMD_NET)
#if defined(CONFIG_NET_MULTI)
puts("Net: ");
#endif
eth_initialize(gd->bd);
#if defined(CONFIG_RESET_PHY_R)
debug("Reset Ethernet PHY\n");
reset_phy();
#endif
#endif
#ifdef CONFIG_POST
post_run(NULL, POST_RAM | post_bootmode_get(0));
#endif
#if defined(CONFIG_PRAM) || defined(CONFIG_LOGBUFFER)
/*
* Export available size of memory for Linux,
* taking into account the protected RAM at top of memory
*/
{
ulong pram;
uchar memsz[32];
#ifdef CONFIG_PRAM
char *s;
s = getenv("pram");
if (s != NULL)
pram = simple_strtoul(s, NULL, 10);
else
pram = CONFIG_PRAM;
#else
pram = 0;
#endif
#ifdef CONFIG_LOGBUFFER
#ifndef CONFIG_ALT_LB_ADDR
/* Also take the logbuffer into account (pram is in kB) */
pram += (LOGBUFF_LEN + LOGBUFF_OVERHEAD) / 1024;
#endif
#endif
sprintf((char *)memsz, "%ldk", (bd->bi_memsize / 1024) - pram);
setenv("mem", (char *)memsz);
}
#endif
/* main_loop() can return to retry autoboot, if so just run it again. */
for (;;) {
main_loop();
}
/* NOTREACHED - no way out of command loop except booting */
}
/*
* This is the next part if the initialization sequence: we are now
* running from RAM and have a "normal" C environment, i. e. global
* data can be written, BSS has been cleared, the stack size in not
* that critical any more, etc.
*/
void board_init_r(gd_t *id, ulong dest_addr)
{
bd_t *bd;
ulong malloc_start;
#ifndef CONFIG_SYS_NO_FLASH
ulong flash_size;
#endif
gd = id; /* initialize RAM version of global data */
bd = gd->bd;
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
/* The Malloc area is immediately below the monitor copy in DRAM */
malloc_start = dest_addr - TOTAL_MALLOC_LEN;
#if defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx)
/*
* The gd->arch.cpu pointer is set to an address in flash before
* relocation. We need to update it to point to the same CPU entry
* in RAM.
*/
gd->arch.cpu += dest_addr - CONFIG_SYS_MONITOR_BASE;
/*
* If we didn't know the cpu mask & # cores, we can save them of
* now rather than 'computing' them constantly
*/
fixup_cpu();
#endif
#ifdef CONFIG_SYS_EXTRA_ENV_RELOC
/*
* Some systems need to relocate the env_addr pointer early because the
* location it points to will get invalidated before env_relocate is
* called. One example is on systems that might use a L2 or L3 cache
* in SRAM mode and initialize that cache from SRAM mode back to being
* a cache in cpu_init_r.
*/
gd->env_addr += dest_addr - CONFIG_SYS_MONITOR_BASE;
#endif
serial_initialize();
debug("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
WATCHDOG_RESET();
/*
* Setup trap handlers
*/
trap_init(dest_addr);
#ifdef CONFIG_ADDR_MAP
init_addr_map();
#endif
#if defined(CONFIG_BOARD_EARLY_INIT_R)
board_early_init_r();
#endif
monitor_flash_len = (ulong)&__init_end - dest_addr;
WATCHDOG_RESET();
#ifdef CONFIG_LOGBUFFER
logbuff_init_ptrs();
#endif
#ifdef CONFIG_POST
post_output_backlog();
#endif
WATCHDOG_RESET();
#if defined(CONFIG_SYS_DELAYED_ICACHE)
icache_enable(); /* it's time to enable the instruction cache */
#endif
#if defined(CONFIG_SYS_INIT_RAM_LOCK) && defined(CONFIG_E500)
unlock_ram_in_cache(); /* it's time to unlock D-cache in e500 */
#endif
#if defined(CONFIG_PCI) && defined(CONFIG_SYS_EARLY_PCI_INIT)
/*
* Do early PCI configuration _before_ the flash gets initialised,
* because PCU ressources are crucial for flash access on some boards.
*/
pci_init();
#endif
#if defined(CONFIG_WINBOND_83C553)
/*
* Initialise the ISA bridge
*/
initialise_w83c553f();
#endif
asm("sync ; isync");
mem_malloc_init(malloc_start, TOTAL_MALLOC_LEN);
#if !defined(CONFIG_SYS_NO_FLASH)
puts("Flash: ");
if (board_flash_wp_on()) {
printf("Uninitialized - Write Protect On\n");
/* Since WP is on, we can't find real size. Set to 0 */
flash_size = 0;
} else if ((flash_size = flash_init()) > 0) {
#ifdef CONFIG_SYS_FLASH_CHECKSUM
print_size(flash_size, "");
/*
* Compute and print flash CRC if flashchecksum is set to 'y'
*
* NOTE: Maybe we should add some WATCHDOG_RESET()? XXX
*/
if (getenv_yesno("flashchecksum") == 1) {
printf(" CRC: %08X",
crc32(0,
(const unsigned char *)
CONFIG_SYS_FLASH_BASE, flash_size)
);
}
putc('\n');
#else /* !CONFIG_SYS_FLASH_CHECKSUM */
print_size(flash_size, "\n");
#endif /* CONFIG_SYS_FLASH_CHECKSUM */
} else {
puts(failed);
hang();
}
/* update start of FLASH memory */
bd->bi_flashstart = CONFIG_SYS_FLASH_BASE;
/* size of FLASH memory (final value) */
bd->bi_flashsize = flash_size;
#if defined(CONFIG_SYS_UPDATE_FLASH_SIZE)
/* Make a update of the Memctrl. */
update_flash_size(flash_size);
#endif
#if defined(CONFIG_OXC) || defined(CONFIG_RMU)
/* flash mapped at end of memory map */
bd->bi_flashoffset = CONFIG_SYS_TEXT_BASE + flash_size;
#elif CONFIG_SYS_MONITOR_BASE == CONFIG_SYS_FLASH_BASE
bd->bi_flashoffset = monitor_flash_len; /* reserved area for monitor */
#endif
#endif /* !CONFIG_SYS_NO_FLASH */
WATCHDOG_RESET();
/* initialize higher level parts of CPU like time base and timers */
cpu_init_r();
WATCHDOG_RESET();
#ifdef CONFIG_SPI
#if !defined(CONFIG_ENV_IS_IN_EEPROM)
spi_init_f();
#endif
spi_init_r();
#endif
#if defined(CONFIG_CMD_NAND)
WATCHDOG_RESET();
puts("NAND: ");
nand_init(); /* go init the NAND */
#endif
#ifdef CONFIG_GENERIC_MMC
/*
* MMC initialization is called before relocating env.
* Thus It is required that operations like pin multiplexer
* be put in board_init.
*/
WATCHDOG_RESET();
puts("MMC: ");
mmc_initialize(bd);
#endif
/* relocate environment function pointers etc. */
env_relocate();
/*
* after non-volatile devices & environment is setup and cpu code have
* another round to deal with any initialization that might require
* full access to the environment or loading of some image (firmware)
* from a non-volatile device
*/
cpu_secondary_init_r();
/*
* Fill in missing fields of bd_info.
* We do this here, where we have "normal" access to the
* environment; we used to do this still running from ROM,
* where had to use getenv_f(), which can be pretty slow when
* the environment is in EEPROM.
*/
#if defined(CONFIG_SYS_EXTBDINFO)
#if defined(CONFIG_405GP) || defined(CONFIG_405EP)
#if defined(CONFIG_I2CFAST)
/*
* set bi_iic_fast for linux taking environment variable
* "i2cfast" into account
*/
{
if (getenv_yesno("i2cfast") == 1) {
bd->bi_iic_fast[0] = 1;
bd->bi_iic_fast[1] = 1;
}
}
#endif /* CONFIG_I2CFAST */
#endif /* CONFIG_405GP, CONFIG_405EP */
#endif /* CONFIG_SYS_EXTBDINFO */
#if defined(CONFIG_SC3)
sc3_read_eeprom();
#endif
#if defined(CONFIG_ID_EEPROM) || defined(CONFIG_SYS_I2C_MAC_OFFSET)
mac_read_from_eeprom();
#endif
#ifdef CONFIG_CMD_NET
/* kept around for legacy kernels only ... ignore the next section */
eth_getenv_enetaddr("ethaddr", bd->bi_enetaddr);
#ifdef CONFIG_HAS_ETH1
eth_getenv_enetaddr("eth1addr", bd->bi_enet1addr);
#endif
#ifdef CONFIG_HAS_ETH2
eth_getenv_enetaddr("eth2addr", bd->bi_enet2addr);
#endif
#ifdef CONFIG_HAS_ETH3
eth_getenv_enetaddr("eth3addr", bd->bi_enet3addr);
#endif
#ifdef CONFIG_HAS_ETH4
eth_getenv_enetaddr("eth4addr", bd->bi_enet4addr);
#endif
#ifdef CONFIG_HAS_ETH5
eth_getenv_enetaddr("eth5addr", bd->bi_enet5addr);
#endif
#endif /* CONFIG_CMD_NET */
WATCHDOG_RESET();
#if defined(CONFIG_PCI) && !defined(CONFIG_SYS_EARLY_PCI_INIT)
/*
* Do pci configuration
*/
pci_init();
#endif
/** leave this here (after malloc(), environment and PCI are working) **/
/* Initialize stdio devices */
stdio_init();
/* Initialize the jump table for applications */
jumptable_init();
#if defined(CONFIG_API)
/* Initialize API */
api_init();
#endif
/* Initialize the console (after the relocation and devices init) */
console_init_r();
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
#if defined(CONFIG_CMD_KGDB)
WATCHDOG_RESET();
puts("KGDB: ");
kgdb_init();
#endif
debug("U-Boot relocated to %08lx\n", dest_addr);
/*
* Enable Interrupts
*/
interrupt_init();
#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
status_led_set(STATUS_LED_BOOT, STATUS_LED_BLINKING);
#endif
udelay(20);
/* Initialize from environment */
load_addr = getenv_ulong("loadaddr", 16, load_addr);
WATCHDOG_RESET();
#if defined(CONFIG_CMD_SCSI)
WATCHDOG_RESET();
puts("SCSI: ");
scsi_init();
#endif
#if defined(CONFIG_CMD_DOC)
WATCHDOG_RESET();
puts("DOC: ");
doc_init();
#endif
#ifdef CONFIG_BITBANGMII
bb_miiphy_init();
#endif
#if defined(CONFIG_CMD_NET)
WATCHDOG_RESET();
puts("Net: ");
eth_initialize(bd);
#endif
#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
WATCHDOG_RESET();
debug("Reset Ethernet PHY\n");
reset_phy();
#endif
#ifdef CONFIG_POST
post_run(NULL, POST_RAM | post_bootmode_get(0));
#endif
#if defined(CONFIG_CMD_PCMCIA) \
&& !defined(CONFIG_CMD_IDE)
WATCHDOG_RESET();
puts("PCMCIA:");
pcmcia_init();
#endif
#if defined(CONFIG_CMD_IDE)
WATCHDOG_RESET();
#ifdef CONFIG_IDE_8xx_PCCARD
puts("PCMCIA:");
#else
puts("IDE: ");
#endif
#if defined(CONFIG_START_IDE)
if (board_start_ide())
ide_init();
#else
ide_init();
#endif
#endif
#ifdef CONFIG_LAST_STAGE_INIT
WATCHDOG_RESET();
/*
* Some parts can be only initialized if all others (like
* Interrupts) are up and running (i.e. the PC-style ISA
* keyboard).
*/
last_stage_init();
#endif
#if defined(CONFIG_CMD_BEDBUG)
WATCHDOG_RESET();
bedbug_init();
#endif
#if defined(CONFIG_PRAM) || defined(CONFIG_LOGBUFFER)
/*
* Export available size of memory for Linux,
* taking into account the protected RAM at top of memory
*/
{
ulong pram = 0;
char memsz[32];
#ifdef CONFIG_PRAM
pram = getenv_ulong("pram", 10, CONFIG_PRAM);
#endif
#ifdef CONFIG_LOGBUFFER
#ifndef CONFIG_ALT_LB_ADDR
/* Also take the logbuffer into account (pram is in kB) */
pram += (LOGBUFF_LEN + LOGBUFF_OVERHEAD) / 1024;
#endif
#endif
sprintf(memsz, "%ldk", (ulong) (bd->bi_memsize / 1024) - pram);
setenv("mem", memsz);
}
#endif
#ifdef CONFIG_PS2KBD
puts("PS/2: ");
kbd_init();
#endif
/* Initialization complete - start the monitor */
/* main_loop() can return to retry autoboot, if so just run it again. */
for (;;) {
WATCHDOG_RESET();
main_loop();
}
/* NOTREACHED - no way out of command loop except booting */
}
void board_init_r(gd_t *id, ulong dest_addr)
{
if (id)
gd = id;
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
#ifdef CONFIG_SERIAL_MULTI
serial_initialize();
#endif
#ifdef CONFIG_POST
post_output_backlog();
#endif
/* The Malloc area is at the top of simulated DRAM */
mem_malloc_init((ulong)gd->ram_buf + gd->ram_size - TOTAL_MALLOC_LEN,
TOTAL_MALLOC_LEN);
/* initialize environment */
env_relocate();
/* IP Address */
gd->bd->bi_ip_addr = getenv_IPaddr("ipaddr");
stdio_init(); /* get the devices list going. */
jumptable_init();
console_init_r(); /* fully init console as a device */
#if defined(CONFIG_DISPLAY_BOARDINFO_LATE)
checkboard();
#endif
#if defined(CONFIG_ARCH_MISC_INIT)
/* miscellaneous arch dependent initialisations */
arch_misc_init();
#endif
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
/* set up exceptions */
interrupt_init();
/* enable exceptions */
enable_interrupts();
#ifdef CONFIG_BOARD_LATE_INIT
board_late_init();
#endif
#ifdef CONFIG_POST
post_run(NULL, POST_RAM | post_bootmode_get(0));
#endif
sandbox_main_loop_init();
/*
* For now, run the main loop. Later we might let this be done
* in the main program.
*/
while (1)
main_loop();
/* NOTREACHED - no way out of command loop except booting */
}
void start_armboot (void)
{
init_fnc_t **init_fnc_ptr;
int i;
uchar *buf;
for (init_fnc_ptr = init_sequence; *init_fnc_ptr; ++init_fnc_ptr) {
if ((*init_fnc_ptr)() != 0) {
hang ();
}
}
misc_init_r();
buf = (uchar*) CFG_LOADADDR;
/* Always first try mmc without checking boot pins */
#ifndef CONFIG_OMAP3_BEAGLE
if ((get_mem_type() == MMC_ONENAND) || (get_mem_type() == MMC_NAND))
#endif /* CONFIG_OMAP3_BEAGLE */
buf += mmc_boot(buf);
if (buf == (uchar *)CFG_LOADADDR) {
if (get_mem_type() == GPMC_NAND){
#ifdef CFG_PRINTF
printf("Booting from nand . . .\n");
#endif
for (i = NAND_UBOOT_START; i < NAND_UBOOT_END; i+= NAND_BLOCK_SIZE){
if (!nand_read_block(buf, i))
buf += NAND_BLOCK_SIZE; /* advance buf ptr */
}
}
if (get_mem_type() == GPMC_ONENAND){
#ifdef CFG_PRINTF
printf("Booting from onenand . . .\n");
#endif
for (i = ONENAND_START_BLOCK; i < ONENAND_END_BLOCK; i++){
if (!onenand_read_block(buf, i))
buf += ONENAND_BLOCK_SIZE;
}
}
}
#if defined (CONFIG_AM3517EVM)
/*
* FIXME: Currently coping uboot image,
* ideally we should leverage XIP feature here
*/
if (get_mem_type() == GPMC_NOR) {
int size;
printf("Booting from NOR Flash...\n");
size = nor_read_boot(buf);
if (size > 0)
buf += size;
}
#endif
if (buf == (uchar *)CFG_LOADADDR)
hang();
/* go run U-Boot and never return */
printf("Starting OS Bootloader...\n");
((init_fnc_t *)CFG_LOADADDR)();
/* should never come here */
}
void board_init_r(gd_t *id, ulong dest_addr)
{
char *s;
//bd_t *bd;
ulong malloc_start;
#ifdef CONFIG_NONCACHE_MEMORY
uint malloc_noncache_start;
#endif
#if !defined(CONFIG_SYS_NO_FLASH)
ulong flash_size;
#endif
int workmode;
int ret;
gd = id;
//bd = gd->bd;
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
monitor_flash_len = _end_ofs;
malloc_start = dest_addr - TOTAL_MALLOC_LEN - sizeof(struct spare_boot_head_t);
#ifdef CONFIG_NONCACHE_MEMORY_SIZE
malloc_start &= (~(0x00100000 -1));
malloc_noncache_start = malloc_start - CONFIG_NONCACHE_MEMORY_SIZE;
gd->malloc_noncache_start = malloc_noncache_start;
#endif
/* Enable caches */
enable_caches();
debug("monitor flash len: %08lX\n", monitor_flash_len);
board_init(); /* Setup chipselects */
#ifdef CONFIG_SERIAL_MULTI
serial_initialize();
#endif
debug("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
#ifdef CONFIG_LOGBUFFER
logbuff_init_ptrs();
#endif
#ifdef CONFIG_POST
post_output_backlog();
#endif
/* The Malloc area is immediately below the monitor copy in DRAM */
mem_malloc_init (malloc_start, TOTAL_MALLOC_LEN);
#ifdef CONFIG_NONCACHE_MEMORY
mem_noncache_malloc_init(malloc_noncache_start, CONFIG_NONCACHE_MEMORY_SIZE);
#endif
workmode = uboot_spare_head.boot_data.work_mode;
debug("work mode %d\n", workmode);
axp_reinit();
//uboot_spare_head.boot_data.work_mode = WORK_MODE_CARD_PRODUCT;
#ifdef CONFIG_ARCH_HOMELET
gpio_control();
#endif
#if 0
#if !defined(CONFIG_SYS_NO_FLASH)
puts("Flash: ");
flash_size = flash_init();
if (flash_size > 0) {
# ifdef CONFIG_SYS_FLASH_CHECKSUM
print_size(flash_size, "");
/*
* Compute and print flash CRC if flashchecksum is set to 'y'
*
* NOTE: Maybe we should add some WATCHDOG_RESET()? XXX
*/
s = getenv("flashchecksum");
if (s && (*s == 'y')) {
printf(" CRC: %08X", crc32(0,
(const unsigned char *) CONFIG_SYS_FLASH_BASE,
flash_size));
}
putc('\n');
# else /* !CONFIG_SYS_FLASH_CHECKSUM */
print_size(flash_size, "\n");
# endif /* CONFIG_SYS_FLASH_CHECKSUM */
} else {
puts(failed);
hang();
}
#endif
#endif
/* set up exceptions */
interrupt_init();
/* enable exceptions */
enable_interrupts();
sunxi_dma_init();
#ifdef CONFIG_ALLWINNER
#ifdef DEBUG
puts("ready to config storage\n");
#endif
if((workmode == WORK_MODE_BOOT) || (workmode == WORK_MODE_CARD_PRODUCT))
{
#if defined(CONFIG_SUNXI_DISPLAY)
drv_disp_init();
#endif
board_display_device_open();
board_display_layer_request();
}
ret = sunxi_flash_handle_init();
if(!ret)
{
sunxi_partition_init();
}
#else
#if defined(CONFIG_CMD_NAND)
if(!storage_type){
puts("NAND: ");
nand_init(); /* go init the NAND */
}
#endif/*CONFIG_CMD_NAND*/
#if defined(CONFIG_GENERIC_MMC)
if(storage_type){
puts("MMC: ");
mmc_initialize(bd);
}
#endif/*CONFIG_GENERIC_MMC*/
#endif/*CONFIG_ALLWINNER*/
#ifdef CONFIG_ARCH_HOMELET
extern int check_boot_recovery_key();
extern int sprite_form_sysrecovery();
extern int sprite_led_init(void);
extern int sprite_led_exit(int status);
if (!check_boot_recovery_key())
{
sprite_led_init();
ret = sprite_form_sysrecovery();
sprite_led_exit(ret);
}
#endif
#ifdef CONFIG_HAS_DATAFLASH
AT91F_DataflashInit();
dataflash_print_info();
#endif
/* initialize environment */
env_relocate();
#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI)
arm_pci_init();
#endif
/* IP Address */
gd->bd->bi_ip_addr = getenv_IPaddr("ipaddr");
stdio_init(); /* get the devices list going. */
jumptable_init();
#if defined(CONFIG_API)
/* Initialize API */
api_init();
#endif
console_init_r(); /* fully init console as a device */
#if defined(CONFIG_ARCH_MISC_INIT)
/* miscellaneous arch dependent initialisations */
arch_misc_init();
#endif
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
/* Perform network card initialisation if necessary */
#if defined(CONFIG_DRIVER_SMC91111) || defined (CONFIG_DRIVER_LAN91C96)
/* XXX: this needs to be moved to board init */
if (getenv("ethaddr")) {
uchar enetaddr[6];
eth_getenv_enetaddr("ethaddr", enetaddr);
smc_set_mac_addr(enetaddr);
}
#endif /* CONFIG_DRIVER_SMC91111 || CONFIG_DRIVER_LAN91C96 */
/* Initialize from environment */
s = getenv("loadaddr");
if (s != NULL)
load_addr = simple_strtoul(s, NULL, 16);
#if defined(CONFIG_CMD_NET)
s = getenv("bootfile");
if (s != NULL)
copy_filename(BootFile, s, sizeof(BootFile));
#endif
#ifdef BOARD_LATE_INIT
board_late_init();
#endif
#ifdef CONFIG_BITBANGMII
bb_miiphy_init();
#endif
#if defined(CONFIG_CMD_NET)
#if defined(CONFIG_NET_MULTI)
puts("Net: ");
#endif
eth_initialize(gd->bd);
#if defined(CONFIG_RESET_PHY_R)
debug("Reset Ethernet PHY\n");
reset_phy();
#endif
#endif
#ifdef CONFIG_POST
post_run(NULL, POST_RAM | post_bootmode_get(0));
#endif
#if defined(CONFIG_PRAM) || defined(CONFIG_LOGBUFFER)
/*
* Export available size of memory for Linux,
* taking into account the protected RAM at top of memory
*/
{
ulong pram;
uchar memsz[32];
#ifdef CONFIG_PRAM
char *s;
s = getenv("pram");
if (s != NULL)
pram = simple_strtoul(s, NULL, 10);
else
pram = CONFIG_PRAM;
#else
pram = 0;
#endif
#ifdef CONFIG_LOGBUFFER
#ifndef CONFIG_ALT_LB_ADDR
/* Also take the logbuffer into account (pram is in kB) */
pram += (LOGBUFF_LEN + LOGBUFF_OVERHEAD) / 1024;
#endif
#endif
sprintf((char *)memsz, "%ldk", (gd->ram_size / 1024) - pram);
setenv("mem", (char *)memsz);
}
#endif
//sprite_cartoon_test();
if(workmode == WORK_MODE_BOOT)
{
#if defined(CONFIG_SUNXI_SCRIPT_REINIT)
{
FATFS script_mount;
int ret;
uint read_bytes = 0;
FIL script_fs;
uchar *buf = NULL;
f_mount(0, &script_mount);
ret = f_open (&script_fs, "0:script.bin", FA_OPEN_EXISTING | FA_READ | FA_WRITE );
if(ret)
{
printf("cant open script.bin, maybe it is not exist\n");
}
else
{
buf = (uchar *)malloc(100 * 1024);
memset(buf, 0, 100 * 1024);
if(!f_read(&script_fs, buf, 100 * 1024, &read_bytes))
{
printf("f_read read bytes = %d\n", read_bytes);
}
f_close(&script_fs);
puts("try to unlink file ");
printf("%d\n", f_unlink("0:script.bin"));
}
f_mount(0, NULL);
if(read_bytes > 0)
{
char *tmp_target_buffer = (char *)(CONFIG_SYS_TEXT_BASE - 0x01000000);
sunxi_flash_exit(1);
memcpy(tmp_target_buffer + uboot_spare_head.boot_head.uboot_length, buf, read_bytes);
sunxi_sprite_download_uboot(tmp_target_buffer, uboot_spare_head.boot_data.storage_type, 1);
reset_cpu(0);
}
if(buf)
{
free(buf);
}
}
#endif
printf("WORK_MODE_BOOT\n");
#ifdef CONFIG_ALLWINNER
#if (defined(CONFIG_SUN6I) || defined(CONFIG_A50) || defined(CONFIG_SUN7I))
if(!ret)
{
#ifndef CONFIG_ARCH_HOMELET
printf("board_status_probe\n");
board_status_probe(0);
#endif
printf("sunxi_bmp_display\n");
sunxi_bmp_display("bootlogo.bmp");
}
#endif
printf("WORK_MODE_BOOT\n");
#endif
}
/* main_loop() can return to retry autoboot, if so just run it again. */
for (;;)
{
main_loop();
}
hang();
/* NOTREACHED - no way out of command loop except booting */
}
void board_init_r(gd_t *id, ulong dest_addr)
{
ulong malloc_start;
#if !defined(CONFIG_SYS_NO_FLASH)
ulong flash_size;
#endif
gd = id;
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
bootstage_mark_name(BOOTSTAGE_ID_START_UBOOT_R, "board_init_r");
monitor_flash_len = _end_ofs;/*u-boot.lds中定义*/
/* Enable caches */
enable_caches();
debug("monitor flash len: %08lX\n", monitor_flash_len);
board_init(); /* Setup chipselects//打印一些版本信息，电源管理信息 */
/*
* TODO: printing of the clock inforamtion of the board is now
* implemented as part of bdinfo command. Currently only support for
* davinci SOC's is added. Remove this check once all the board
* implement this.
*/
#ifdef CONFIG_CLOCKS
set_cpu_clk_info(); /* Setup clock information */
#endif
#ifdef CONFIG_SERIAL_MULTI
#ifndef CONFIG_CPU_EXYNOS5410
serial_initialize();
#endif
#endif
debug("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
#ifdef CONFIG_LOGBUFFER
logbuff_init_ptrs();
#endif
#ifdef CONFIG_POST
post_output_backlog();
#endif
/* The Malloc area is immediately below the monitor copy in DRAM */
malloc_start = dest_addr - TOTAL_MALLOC_LEN;
mem_malloc_init (malloc_start, TOTAL_MALLOC_LEN);
#ifdef CONFIG_ARCH_EARLY_INIT_R
arch_early_init_r();
#endif
#if !defined(CONFIG_SYS_NO_FLASH)
puts("Flash: ");
flash_size = flash_init();
if (flash_size > 0) {
# ifdef CONFIG_SYS_FLASH_CHECKSUM
char *s = getenv("flashchecksum");
print_size(flash_size, "");
/*
* Compute and print flash CRC if flashchecksum is set to 'y'
*
* NOTE: Maybe we should add some WATCHDOG_RESET()? XXX
*/
if (s && (*s == 'y')) {
printf(" CRC: %08X", crc32(0,
(const unsigned char *) CONFIG_SYS_FLASH_BASE,
flash_size));
}
putc('\n');
# else /* !CONFIG_SYS_FLASH_CHECKSUM */
print_size(flash_size, "\n");
# endif /* CONFIG_SYS_FLASH_CHECKSUM */
} else {
puts(failed);
hang();
}
#endif
#if defined(CONFIG_CMD_NAND)
puts("NAND: ");
nand_init(); /* go init the NAND */
#endif
#if defined(CONFIG_CMD_ONENAND)
onenand_init();
#endif
#ifdef CONFIG_GENERIC_MMC
puts("MMC: ");
mmc_initialize(gd->bd);
#endif
#ifdef CONFIG_HAS_DATAFLASH
AT91F_DataflashInit();
dataflash_print_info();
#endif
/* initialize environment */
env_relocate();
#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI)
arm_pci_init();
#endif
stdio_init(); /* get the devices list going. */
jumptable_init();
#if defined(CONFIG_API)
/* Initialize API */
api_init();
#endif
console_init_r(); /* fully init console as a device */
#if defined(CONFIG_ARCH_MISC_INIT)
/* miscellaneous arch dependent initialisations */
arch_misc_init();
#endif
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
/* set up exceptions */
interrupt_init();
/* enable exceptions */
enable_interrupts();
/* Perform network card initialisation if necessary */
#if defined(CONFIG_DRIVER_SMC91111) || defined (CONFIG_DRIVER_LAN91C96)
/* XXX: this needs to be moved to board init */
if (getenv("ethaddr")) {
uchar enetaddr[6];
eth_getenv_enetaddr("ethaddr", enetaddr);
smc_set_mac_addr(enetaddr);
}
#endif /* CONFIG_DRIVER_SMC91111 || CONFIG_DRIVER_LAN91C96 */
/* Initialize from environment */
load_addr = getenv_ulong("loadaddr", 16, load_addr);
#ifdef CONFIG_BOARD_LATE_INIT
board_late_init();//晚点执行的初始化在smdk5420.c
#endif
#ifdef CONFIG_BITBANGMII
bb_miiphy_init();
#endif
#if defined(CONFIG_CMD_NET)
puts("Net: ");
eth_initialize(gd->bd);
#if defined(CONFIG_RESET_PHY_R)
debug("Reset Ethernet PHY\n");
reset_phy();
#endif
#endif
#ifdef CONFIG_POST
post_run(NULL, POST_RAM | post_bootmode_get(0));
#endif
#if defined(CONFIG_PRAM) || defined(CONFIG_LOGBUFFER)
/*
* Export available size of memory for Linux,
* taking into account the protected RAM at top of memory
*/
{
ulong pram = 0;
uchar memsz[32];
#ifdef CONFIG_PRAM
pram = getenv_ulong("pram", 10, CONFIG_PRAM);
#endif
#ifdef CONFIG_LOGBUFFER
#ifndef CONFIG_ALT_LB_ADDR
/* Also take the logbuffer into account (pram is in kB) */
pram += (LOGBUFF_LEN + LOGBUFF_OVERHEAD) / 1024;
#endif
#endif
sprintf((char *)memsz, "%ldk", (gd->ram_size / 1024) - pram);
setenv("mem", (char *)memsz);
}
#endif
/* main_loop() can return to retry autoboot, if so just run it again. */
for (;;) {
main_loop();//进入命令行模式
}
/* NOTREACHED - no way out of command loop except booting */
}
void board_init_r(gd_t *id, ulong dest_addr)
{
#ifndef CONFIG_SYS_NO_FLASH
ulong size;
#endif
extern void malloc_bin_reloc(void);
#ifndef CONFIG_ENV_IS_NOWHERE
extern char *env_name_spec;
#endif
bd_t *bd;
gd = id;
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
debug("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
gd->reloc_off = dest_addr - CONFIG_SYS_MONITOR_BASE;
monitor_flash_len = (ulong)&uboot_end_data - dest_addr;
#if defined(CONFIG_NEEDS_MANUAL_RELOC)
/*
* We have to relocate the command table manually
*/
fixup_cmdtable(&__u_boot_cmd_start,
(ulong)(&__u_boot_cmd_end - &__u_boot_cmd_start));
#endif /* defined(CONFIG_NEEDS_MANUAL_RELOC) */
/* there are some other pointer constants we must deal with */
#ifndef CONFIG_ENV_IS_NOWHERE
env_name_spec += gd->reloc_off;
#endif
bd = gd->bd;
/* The Malloc area is immediately below the monitor copy in DRAM */
mem_malloc_init(CONFIG_SYS_MONITOR_BASE + gd->reloc_off -
TOTAL_MALLOC_LEN, TOTAL_MALLOC_LEN);
malloc_bin_reloc();
#ifndef CONFIG_SYS_NO_FLASH
/* configure available FLASH banks */
size = flash_init();
display_flash_config(size);
bd->bi_flashsize = size;
#endif
bd->bi_flashstart = CONFIG_SYS_FLASH_BASE;
#if CONFIG_SYS_MONITOR_BASE == CONFIG_SYS_FLASH_BASE
bd->bi_flashoffset = monitor_flash_len; /* reserved area for U-Boot */
#else
bd->bi_flashoffset = 0;
#endif
#ifdef CONFIG_CMD_NAND
puts("NAND: ");
nand_init(); /* go init the NAND */
#endif
#if defined(CONFIG_CMD_ONENAND)
onenand_init();
#endif
/* relocate environment function pointers etc. */
env_relocate();
/* IP Address */
bd->bi_ip_addr = getenv_IPaddr("ipaddr");
#if defined(CONFIG_PCI)
/*
* Do pci configuration
*/
pci_init();
#endif
/** leave this here (after malloc(), environment and PCI are working) **/
/* Initialize stdio devices */
stdio_init();
jumptable_init();
/* Initialize the console (after the relocation and devices init) */
console_init_r();
/** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** **/
/* Initialize from environment */
load_addr = getenv_ulong("loadaddr", 16, load_addr);
#if defined(CONFIG_CMD_NET)
{
char *s = getenv("bootfile");
if (s != NULL)
copy_filename(BootFile, s, sizeof(BootFile));
}
#endif
#ifdef CONFIG_CMD_SPI
puts("SPI: ");
spi_init(); /* go init the SPI */
puts("ready\n");
#endif
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
#ifdef CONFIG_BITBANGMII
bb_miiphy_init();
#endif
#if defined(CONFIG_CMD_NET)
puts("Net: ");
eth_initialize(gd->bd);
#endif
/* main_loop() can return to retry autoboot, if so just run it again. */
for (;;)
main_loop();
/* NOTREACHED - no way out of command loop except booting */
}
void board_init_r(gd_t *id, ulong dest_addr)
{
char *s;
ulong size;
static bd_t bd_data;
static gd_t gd_data;
init_fnc_t **init_fnc_ptr;
show_boot_progress(0x21);
/* Global data pointer is now writable */
gd = &gd_data;
memcpy(gd, id, sizeof(gd_t));
/* compiler optimization barrier needed for GCC >= 3.4 */
__asm__ __volatile__("": : :"memory");
gd->bd = &bd_data;
memset (gd->bd, 0, sizeof (bd_t));
show_boot_progress(0x22);
gd->baudrate = CONFIG_BAUDRATE;
mem_malloc_init((((ulong)dest_addr - CONFIG_SYS_MALLOC_LEN)+3)&~3,
CONFIG_SYS_MALLOC_LEN);
for (init_fnc_ptr = init_sequence_r; *init_fnc_ptr; ++init_fnc_ptr) {
if ((*init_fnc_ptr)() != 0)
hang ();
}
show_boot_progress(0x23);
#ifdef CONFIG_SERIAL_MULTI
serial_initialize();
#endif
/* configure available FLASH banks */
size = flash_init();
display_flash_config(size);
show_boot_progress(0x24);
show_boot_progress(0x25);
/* initialize environment */
env_relocate ();
show_boot_progress(0x26);
#ifdef CONFIG_CMD_NET
/* IP Address */
bd_data.bi_ip_addr = getenv_IPaddr ("ipaddr");
#endif
#if defined(CONFIG_PCI)
/*
* Do pci configuration
*/
pci_init();
#endif
show_boot_progress(0x27);
stdio_init ();
jumptable_init ();
/* Initialize the console (after the relocation and devices init) */
console_init_r();
#ifdef CONFIG_MISC_INIT_R
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
#if defined(CONFIG_CMD_PCMCIA) && !defined(CONFIG_CMD_IDE)
WATCHDOG_RESET();
puts ("PCMCIA:");
pcmcia_init();
#endif
#if defined(CONFIG_CMD_KGDB)
WATCHDOG_RESET();
puts("KGDB: ");
kgdb_init();
#endif
/* enable exceptions */
enable_interrupts();
show_boot_progress(0x28);
#ifdef CONFIG_STATUS_LED
status_led_set (STATUS_LED_BOOT, STATUS_LED_BLINKING);
#endif
udelay(20);
/* Initialize from environment */
load_addr = getenv_ulong("loadaddr", 16, load_addr);
#if defined(CONFIG_CMD_NET)
if ((s = getenv ("bootfile")) != NULL) {
copy_filename (BootFile, s, sizeof (BootFile));
}
#endif
WATCHDOG_RESET();
#if defined(CONFIG_CMD_IDE)
WATCHDOG_RESET();
puts("IDE: ");
ide_init();
#endif
#if defined(CONFIG_CMD_SCSI)
WATCHDOG_RESET();
puts("SCSI: ");
scsi_init();
#endif
#if defined(CONFIG_CMD_DOC)
WATCHDOG_RESET();
puts("DOC: ");
doc_init();
#endif
#ifdef CONFIG_BITBANGMII
bb_miiphy_init();
#endif
#if defined(CONFIG_CMD_NET)
WATCHDOG_RESET();
puts("Net: ");
eth_initialize(gd->bd);
#endif
#if ( defined(CONFIG_CMD_NET)) && (0)
WATCHDOG_RESET();
# ifdef DEBUG
puts ("Reset Ethernet PHY\n");
# endif
reset_phy();
#endif
#ifdef CONFIG_LAST_STAGE_INIT
WATCHDOG_RESET();
/*
* Some parts can be only initialized if all others (like
* Interrupts) are up and running (i.e. the PC-style ISA
* keyboard).
*/
last_stage_init();
#endif
#ifdef CONFIG_POST
post_run (NULL, POST_RAM | post_bootmode_get(0));
#endif
show_boot_progress(0x29);
/* main_loop() can return to retry autoboot, if so just run it again. */
for (;;) {
main_loop();
}
/* NOTREACHED - no way out of command loop except booting */
}
void board_init_r(gd_t *id, ulong dest_addr)
{
#ifndef CONFIG_SYS_NO_FLASH
ulong size;
#endif
bd_t *bd;
gd = id;
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
debug("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
gd->reloc_off = dest_addr - CONFIG_SYS_MONITOR_BASE;
monitor_flash_len = image_copy_end() - dest_addr;
serial_initialize();
bd = gd->bd;
/* The Malloc area is immediately below the monitor copy in DRAM */
mem_malloc_init(CONFIG_SYS_MONITOR_BASE + gd->reloc_off -
TOTAL_MALLOC_LEN, TOTAL_MALLOC_LEN);
#ifndef CONFIG_SYS_NO_FLASH
/* configure available FLASH banks */
size = flash_init();
display_flash_config(size);
bd->bi_flashstart = CONFIG_SYS_FLASH_BASE;
bd->bi_flashsize = size;
#if CONFIG_SYS_MONITOR_BASE == CONFIG_SYS_FLASH_BASE
bd->bi_flashoffset = monitor_flash_len; /* reserved area for U-Boot */
#else
bd->bi_flashoffset = 0;
#endif
#else
bd->bi_flashstart = 0;
bd->bi_flashsize = 0;
bd->bi_flashoffset = 0;
#endif
#ifdef CONFIG_CMD_NAND
puts("NAND: ");
nand_init(); /* go init the NAND */
#endif
#if defined(CONFIG_CMD_ONENAND)
onenand_init();
#endif
/* relocate environment function pointers etc. */
env_relocate();
#if defined(CONFIG_PCI)
/*
* Do pci configuration
*/
pci_init();
#endif
/** leave this here (after malloc(), environment and PCI are working) **/
/* Initialize stdio devices */
stdio_init();
jumptable_init();
/* Initialize the console (after the relocation and devices init) */
console_init_r();
/** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** ** **/
/* Initialize from environment */
load_addr = getenv_ulong("loadaddr", 16, load_addr);
#ifdef CONFIG_CMD_SPI
puts("SPI: ");
spi_init(); /* go init the SPI */
puts("ready\n");
#endif
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
#ifdef CONFIG_BITBANGMII
bb_miiphy_init();
#endif
#if defined(CONFIG_CMD_NET)
puts("Net: ");
eth_initialize(gd->bd);
#endif
/* main_loop() can return to retry autoboot, if so just run it again. */
for (;;)
main_loop();
/* NOTREACHED - no way out of command loop except booting */
}
void start_armboot (void)
{
init_fnc_t **init_fnc_ptr;
char *s;
ulong size;
#if defined(CONFIG_VFD) || defined(CONFIG_LCD)
unsigned long addr;
#endif
#ifdef CFG_UBOOT_PROFILING
unsigned int time_start_armboot = get_timer(0);
unsigned int time_init_sequence;
unsigned int time_misc_init;
unsigned int time_env;
unsigned int time_nand;
unsigned int time_bat;
unsigned int time_show_logo;
unsigned int time_backlight;
unsigned int time_sw_env;
#endif
#ifdef CFG_UBOOT_PROFILING
boot_time = get_timer(0);
#endif
/* Pointer is writable since we allocated a register for it */
gd = (gd_t*)(_armboot_start - CONFIG_SYS_MALLOC_LEN - sizeof(gd_t));
/* compiler optimization barrier needed for GCC >= 3.4 */
__asm__ __volatile__("": : :"memory");
memset ((void*)gd, 0, sizeof (gd_t));
gd->bd = (bd_t*)((char*)gd - sizeof(bd_t));
memset (gd->bd, 0, sizeof (bd_t));
monitor_flash_len = _bss_start - _armboot_start;
#ifdef CFG_UBOOT_PROFILING
time_init_sequence = get_timer(0);
#endif
for (init_fnc_ptr = init_sequence; *init_fnc_ptr; ++init_fnc_ptr)
{
if ((*init_fnc_ptr)() != 0) {
hang ();
}
}
/* armboot_start is defined in the board-specific linker script */
mem_malloc_init (_armboot_start - CONFIG_SYS_MALLOC_LEN, CONFIG_SYS_MALLOC_LEN);
#ifdef CFG_UBOOT_PROFILING
printf("[PROFILE] ------- init_sequence takes %d ms -------- \n", get_timer(time_init_sequence));
#endif
#ifndef CONFIG_SYS_NO_FLASH
/* configure available FLASH banks */
display_flash_config (flash_init ());
#endif /* CONFIG_SYS_NO_FLASH */
#ifdef CONFIG_VFD
#ifndef PAGE_SIZE
#define PAGE_SIZE 4096
#endif
/*
* reserve memory for VFD display (always full pages)
*/
/* bss_end is defined in the board-specific linker script */
addr = (_bss_end + (PAGE_SIZE - 1)) & ~(PAGE_SIZE - 1);
size = vfd_setmem (addr);
gd->fb_base = addr;
#endif /* CONFIG_VFD */
#ifdef CONFIG_LCD
#ifndef PAGE_SIZE
#define PAGE_SIZE 4096
#endif
/*
* reserve memory for LCD display (always full pages)
*/
/* bss_end is defined in the board-specific linker script */
addr = (_bss_end + (PAGE_SIZE - 1)) & ~(PAGE_SIZE - 1);
size = lcd_setmem (addr);
gd->fb_base = addr;
#endif /* CONFIG_LCD */
#ifdef CONFIG_HAS_DATAFLASH
AT91F_DataflashInit();
dataflash_print_info();
#endif
#ifdef CFG_UBOOT_PROFILING
time_env = get_timer(0);
#endif
/* initialize environment */
env_relocate ();
#ifdef CFG_UBOOT_PROFILING
printf("[PROFILE] ------- env relocate takes %d ms -------- \n", get_timer(time_env));
#endif
#ifdef CONFIG_VFD
/* must do this after the framebuffer is allocated */
drv_vfd_init();
#endif /* CONFIG_VFD */
/* IP Address */
//gd->bd->bi_ip_addr = getenv_IPaddr ("ipaddr");
stdio_init (); /* get the devices list going. */
#ifdef CONFIG_CMC_PU2
load_sernum_ethaddr ();
#endif /* CONFIG_CMC_PU2 */
jumptable_init ();
//console_init_r (); /* fully init console as a device */ //marked by hong-rong
#if defined(CONFIG_CMD_NAND)
#ifdef CFG_UBOOT_PROFILING
time_nand= get_timer(0);
#endif
puts ("NAND: ");
nand_init(); /* go init the NAND */
#ifdef CFG_UBOOT_PROFILING
printf("[PROFILE] ------- nand init takes %d ms -------- \n", get_timer(time_nand));
#endif
#endif
#if defined(CONFIG_ARCH_MISC_INIT)
/* miscellaneous arch dependent initialisations */
arch_misc_init ();
#endif
#ifdef CFG_UBOOT_PROFILING
time_misc_init= get_timer(0);
#endif
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r ();
#endif
#ifdef CFG_UBOOT_PROFILING
printf("[PROFILE] ------- misc_init takes %d ms -------- \n", get_timer(time_misc_init));
#endif
#ifdef CONFIG_GENERIC_MMC
puts ("MMC: ");
mmc_initialize (gd->bd);
#endif
#ifdef CFG_POWER_CHARGING
#ifdef CFG_UBOOT_PROFILING
time_bat= get_timer(0);
#endif
#if defined(MT6516)
mt6516_bat_init();
#else
mt65xx_bat_init();
#endif
#ifdef CFG_UBOOT_PROFILING
printf("[PROFILE] ------- battery init takes %d ms -------- \n", get_timer(time_bat));
#endif
#else
/* NOTE: if define CFG_POWER_CHARGING, will rtc_boot_check() in mt65xx_bat_init() */
rtc_boot_check(false);
#endif
#ifdef CFG_UBOOT_PROFILING
time_show_logo= get_timer(0);
#endif
// Some driver refresh RAM data to LCM after sleeping out.
// LCM must sleep out before backlight on. Or Users may see the mess data in LCM in a instance.
mt65xx_disp_power(1);
if(g_boot_mode != ALARM_BOOT)
{
mt65xx_disp_show_boot_logo();
}
#ifdef CFG_UBOOT_PROFILING
printf("[PROFILE] ------- show logo takes %d ms -------- \n", get_timer(time_show_logo));
#endif
#ifdef CFG_UBOOT_PROFILING
time_show_logo= get_timer(0);
#endif
#ifdef CFG_UBOOT_PROFILING
time_backlight= get_timer(0);
#endif
mt65xx_backlight_on();
#ifdef CFG_UBOOT_PROFILING
printf("[PROFILE] ------- backlight takes %d ms -------- \n", get_timer(time_backlight));
#endif
#ifdef CFG_UBOOT_PROFILING
time_sw_env= get_timer(0);
#endif
//*****************
//* prepare mt65xx sw enviroment
#if defined(MT6516)
mt6516_sw_env();
#else
mt65xx_sw_env();
#endif
#ifdef CFG_UBOOT_PROFILING
printf("[PROFILE] ------- sw_env takes %d ms -------- \n", get_timer(time_sw_env));
#endif
#ifdef CFG_UBOOT_PROFILING
printf("[PROFILE] ------- start_armboot takes %d ms -------- \n", get_timer(time_start_armboot));
#endif
/* main_loop() can return to retry autoboot, if so just run it again */
for (;;) {
main_loop ();
}
/* NOTREACHED - no way out of command loop except booting */
}
/*
************************************************************************
*
* This is the next part if the initialization sequence: we are now
* running from RAM and have a "normal" C environment, i. e. global
* data can be written, BSS has been cleared, the stack size in not
* that critical any more, etc.
*
************************************************************************
*/
void board_init_r(gd_t *id, ulong dest_addr)
{
char *s;
//bd_t *bd;
ulong malloc_start;
#ifdef CONFIG_NONCACHE_MEMORY
uint malloc_noncache_start;
#endif
#if !defined(CONFIG_SYS_NO_FLASH)
ulong flash_size;
#endif
int workmode;
int ret;
#ifdef CONFIG_SUNXI_HDCP_IN_SECURESTORAGE
int hdcpkey_enable=0;
#endif
char storage_type_buf[24] = {0};
char boot_mmc_buf[24] = {0};
gd = id;
//bd = gd->bd;
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
monitor_flash_len = _end_ofs;
malloc_start = dest_addr - TOTAL_MALLOC_LEN - sizeof(struct spare_boot_head_t);
#ifdef CONFIG_NONCACHE_MEMORY_SIZE
malloc_start &= (~(0x00100000 -1));
malloc_noncache_start = malloc_start - CONFIG_NONCACHE_MEMORY_SIZE;
gd->malloc_noncache_start = malloc_noncache_start;
#endif
/* Enable caches */
enable_caches();
debug("monitor flash len: %08lX\n", monitor_flash_len);
board_init(); /* Setup chipselects */
#ifdef CONFIG_SERIAL_MULTI
serial_initialize();
#endif
debug("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
#ifdef CONFIG_LOGBUFFER
logbuff_init_ptrs();
#endif
#ifdef CONFIG_POST
post_output_backlog();
#endif
/* The Malloc area is immediately below the monitor copy in DRAM */
mem_malloc_init (malloc_start, TOTAL_MALLOC_LEN);
#ifdef CONFIG_SMALL_MEMSIZE
save_config();
#endif
#ifdef CONFIG_NONCACHE_MEMORY
mem_noncache_malloc_init(malloc_noncache_start, CONFIG_NONCACHE_MEMORY_SIZE);
#endif
#if defined(CONFIG_ARCH_HOMELET)
check_physical_key_early();
#endif
workmode = uboot_spare_head.boot_data.work_mode;
debug("work mode %d\n", workmode);
axp_reinit();
//uboot_spare_head.boot_data.work_mode = WORK_MODE_CARD_PRODUCT;
#if defined(CONFIG_CPUS_STANDBY) //Ŀǰֻ��homelet��ʹ��
do_box_standby();
#endif
#ifdef CONFIG_ARCH_HOMELET
gpio_control();
#endif
#if 0
#if !defined(CONFIG_SYS_NO_FLASH)
puts("Flash: ");
flash_size = flash_init();
if (flash_size > 0) {
# ifdef CONFIG_SYS_FLASH_CHECKSUM
print_size(flash_size, "");
/*
* Compute and print flash CRC if flashchecksum is set to 'y'
*
* NOTE: Maybe we should add some WATCHDOG_RESET()? XXX
*/
s = getenv("flashchecksum");
if (s && (*s == 'y')) {
printf(" CRC: %08X", crc32(0,
(const unsigned char *) CONFIG_SYS_FLASH_BASE,
flash_size));
}
putc('\n');
# else /* !CONFIG_SYS_FLASH_CHECKSUM */
print_size(flash_size, "\n");
# endif /* CONFIG_SYS_FLASH_CHECKSUM */
} else {
puts(failed);
hang();
}
#endif
#endif
/* set up exceptions */
interrupt_init();
/* enable exceptions */
enable_interrupts();
sunxi_dma_init();
#ifdef CONFIG_USE_CIR //����ӿڣ�Ŀǰֻ���ں��� A20
if (uboot_spare_head.boot_data.work_mode == WORK_MODE_BOOT)
{
ir_setup();
}
#endif
#ifdef DEBUG
puts("ready to config storage\n");
#endif
#ifdef CONFIG_ARCH_HOMELET //for homlet to use one-key-recovery
ret = sunxi_flash_handle_init();
if(!ret)
{
sunxi_partition_init();
}
#endif
#ifndef CONFIG_ARCH_SUN8IW8P1
if((workmode == WORK_MODE_BOOT) || (workmode == WORK_MODE_CARD_PRODUCT) || (workmode == WORK_MODE_SPRITE_RECOVERY))
{
#else
if((workmode == WORK_MODE_CARD_PRODUCT) || (workmode == WORK_MODE_SPRITE_RECOVERY))
{
#endif
#if (defined(CONFIG_SUNXI_DISPLAY) || defined(CONFIG_SUN7I_DISPLAY))
drv_disp_init();
#endif
#ifdef CONFIG_SUNXI_HDCP_IN_SECURESTORAGE
int tmp = 0;
tmp = script_parser_fetch("hdmi_para", "hdmi_hdcp_enable", &hdcpkey_enable, 1);
if((tmp) || (hdcpkey_enable != 1))
{
board_display_device_open();
board_display_layer_request();
}
#else
board_display_device_open();
board_display_layer_request();
#endif
}
#ifndef CONFIG_ARCH_HOMELET //for pad used
ret = sunxi_flash_handle_init();
if(!ret)
{
sunxi_partition_init();
}
#endif
#ifdef CONFIG_SUNXI_HDCP_IN_SECURESTORAGE
//here: write key to hardware
if(hdcpkey_enable==1)
{
char buffer[4096];
int data_len;
int ret0;
memset(buffer, 0, 4096);
ret0 = sunxi_secure_storage_init();
if(ret0)
{
printf("sunxi init secure storage failed\n");
}
else
{
ret0 = sunxi_secure_object_read("hdcpkey", buffer, 4096, &data_len);
if(ret0)
{
printf("probe hdcp key failed\n");
}
else
{
ret0 = smc_aes_bssk_decrypt_to_keysram(buffer, data_len);
if(ret0)
{
printf("push hdcp key failed\n");
}
else
{
board_display_device_open();
board_display_layer_request();
}
}
}
}
#endif
#ifdef CONFIG_BOOT_A15
if(sunxi_sprite_download_boot0_simple())
{
printf("rewrite boot0 to save boot cpu failed\n");
}
#endif
#ifndef CONFIG_SUNXI_SPINOR_PLATFORM
sunxi_keydata_burn_by_usb();
#endif
//#else
//#if defined(CONFIG_CMD_NAND)
// if(!storage_type){
// puts("NAND: ");
// nand_init(); /* go init the NAND */
// }
//#endif/*CONFIG_CMD_NAND*/
//
//#if defined(CONFIG_GENERIC_MMC)
// if(storage_type){
// puts("MMC: ");
// mmc_initialize(bd);
// }
//#endif/*CONFIG_GENERIC_MMC*/
#ifdef CONFIG_HAS_DATAFLASH
AT91F_DataflashInit();
dataflash_print_info();
#endif
/* initialize environment */
env_relocate();
/* setenv storage_type */
sprintf(storage_type_buf, "%d", uboot_spare_head.boot_data.storage_type);
if (setenv("storage_type", storage_type_buf))
printf("set storage_type=%s fail\n", storage_type_buf);
if (uboot_spare_head.boot_data.storage_type == 1)
sprintf(boot_mmc_buf, "%s", "0");
else
sprintf(boot_mmc_buf, "%s", "2");
setenv("boot_mmc", boot_mmc_buf);
#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI)
arm_pci_init();
#endif
/* IP Address */
gd->bd->bi_ip_addr = getenv_IPaddr("ipaddr");
stdio_init(); /* get the devices list going. */
jumptable_init();
#if defined(CONFIG_API)
/* Initialize API */
api_init();
#endif
console_init_r(); /* fully init console as a device */
#if defined(CONFIG_ARCH_MISC_INIT)
/* miscellaneous arch dependent initialisations */
arch_misc_init();
#endif
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
/* Perform network card initialisation if necessary */
#if defined(CONFIG_DRIVER_SMC91111) || defined (CONFIG_DRIVER_LAN91C96)
/* XXX: this needs to be moved to board init */
if (getenv("ethaddr")) {
uchar enetaddr[6];
eth_getenv_enetaddr("ethaddr", enetaddr);
smc_set_mac_addr(enetaddr);
}
#endif /* CONFIG_DRIVER_SMC91111 || CONFIG_DRIVER_LAN91C96 */
/* Initialize from environment */
s = getenv("loadaddr");
if (s != NULL)
load_addr = simple_strtoul(s, NULL, 16);
#if defined(CONFIG_CMD_NET)
s = getenv("bootfile");
if (s != NULL)
copy_filename(BootFile, s, sizeof(BootFile));
#endif
#ifdef BOARD_LATE_INIT
board_late_init();
#endif
#ifdef CONFIG_BITBANGMII
bb_miiphy_init();
#endif
#if defined(CONFIG_CMD_NET)
#if defined(CONFIG_NET_MULTI)
puts("Net: ");
#endif
eth_initialize(gd->bd);
#if defined(CONFIG_RESET_PHY_R)
debug("Reset Ethernet PHY\n");
reset_phy();
#endif
#endif
#ifdef CONFIG_POST
post_run(NULL, POST_RAM | post_bootmode_get(0));
#endif
#if defined(CONFIG_PRAM) || defined(CONFIG_LOGBUFFER)
/*
* Export available size of memory for Linux,
* taking into account the protected RAM at top of memory
*/
{
ulong pram;
uchar memsz[32];
#ifdef CONFIG_PRAM
char *s;
s = getenv("pram");
if (s != NULL)
pram = simple_strtoul(s, NULL, 10);
else
pram = CONFIG_PRAM;
#else
pram = 0;
#endif
#ifdef CONFIG_LOGBUFFER
#ifndef CONFIG_ALT_LB_ADDR
/* Also take the logbuffer into account (pram is in kB) */
pram += (LOGBUFF_LEN + LOGBUFF_OVERHEAD) / 1024;
#endif
#endif
sprintf((char *)memsz, "%ldk", (gd->ram_size / 1024) - pram);
setenv("mem", (char *)memsz);
}
#endif
//sprite_cartoon_test();
if(workmode == WORK_MODE_BOOT)
{
#if defined(CONFIG_SUNXI_SCRIPT_REINIT)
{
FATFS script_mount;
int ret;
uint read_bytes = 0;
FILE script_fs;
uchar *buf = NULL;
f_mount_ex(0, &script_mount, 0);
ret = f_open (&script_fs, "0:script.bin", FA_OPEN_EXISTING | FA_READ | FA_WRITE );
if(ret)
{
printf("cant open script.bin, maybe it is not exist\n");
}
else
{
buf = (uchar *)malloc(100 * 1024);
memset(buf, 0, 100 * 1024);
if(!f_read(&script_fs, buf, 100 * 1024, &read_bytes))
{
printf("f_read read bytes = %d\n", read_bytes);
}
f_close(&script_fs);
puts("try to unlink file ");
printf("%d\n", f_unlink("0:script.bin"));
}
f_mount(0, NULL, NULL);
if(read_bytes > 0)
{
char *tmp_target_buffer = (char *)(CONFIG_SYS_TEXT_BASE - 0x01000000);
sunxi_flash_exit(1);
memcpy(tmp_target_buffer + uboot_spare_head.boot_head.uboot_length, buf, read_bytes);
sunxi_sprite_download_uboot(tmp_target_buffer, uboot_spare_head.boot_data.storage_type, 1);
reset_cpu(0);
}
if(buf)
{
free(buf);
}
}
#endif
printf("WORK_MODE_BOOT\n");
#if (defined(CONFIG_SUNXI_DISPLAY) || defined(CONFIG_SUN7I_DISPLAY))
if(!ret)
{
#ifndef CONFIG_ARCH_HOMELET
printf("board_status_probe\n");
board_status_probe(0);
#endif
if(!gd->chargemode)
{
if(sunxi_advert_disp_probe())
{
printf("sunxi_bmp_logo_display\n");
sunxi_bmp_display("bootlogo.bmp");
}
else
{
if(sunxi_advert_display("Reserve0", "advert.bmp"))
{
printf("sunxi_bmp_logo_display\n");
sunxi_bmp_display("bootlogo.bmp");
}
}
}
else
{
printf("sunxi_bmp_charger_display\n");
sunxi_bmp_display("bat\\battery_charge.bmp");
}
}
#endif
#ifdef CONFIG_READ_LOGO_FOR_KERNEL
sunxi_read_bootlogo("boot_logo");
#endif
}
/* main_loop() can return to retry autoboot, if so just run it again. */
for (;;)
{
main_loop();
}
hang();
/* NOTREACHED - no way out of command loop except booting */
}
void hang(void)
{
puts("### ERROR ### Please RESET the board ###\n");
for (;;);
}
/*
* This is the next part if the initialization sequence: we are now
* running from RAM and have a "normal" C environment, i. e. global
* data can be written, BSS has been cleared, the stack size in not
* that critical any more, etc.
*/
void board_init_r(gd_t *id, ulong dest_addr)
{
char *s;
bd_t *bd;
ulong malloc_start;
extern void malloc_bin_reloc(void);
gd = id;
bd = gd->bd;
gd->flags |= GD_FLG_RELOC; /* tell others: relocation done */
monitor_flash_len = &_end - &_start;
debug("monitor flash len: %08lX\n", monitor_flash_len);
board_init(); /* Setup chipselects */
#if defined(CONFIG_NEEDS_MANUAL_RELOC)
/*
* We have to relocate the command table manually
*/
fixup_cmdtable(&__u_boot_cmd_start,
(ulong)(&__u_boot_cmd_end - &__u_boot_cmd_start));
#endif /* defined(CONFIG_NEEDS_MANUAL_RELOC) */
#ifdef CONFIG_SERIAL_MULTI
serial_initialize();
#endif
debug("Now running in RAM - U-Boot at: %08lx\n", dest_addr);
/* The Malloc area is immediately below the monitor copy in DRAM */
malloc_start = dest_addr - TOTAL_MALLOC_LEN;
mem_malloc_init(malloc_start, TOTAL_MALLOC_LEN);
malloc_bin_reloc();
#ifndef CONFIG_SYS_NO_FLASH
/* configure available FLASH banks */
gd->bd->bi_flashstart = CONFIG_SYS_FLASH_BASE;
gd->bd->bi_flashsize = flash_init();
gd->bd->bi_flashoffset = CONFIG_SYS_FLASH_BASE + gd->bd->bi_flashsize;
if (gd->bd->bi_flashsize)
display_flash_config(gd->bd->bi_flashsize);
#endif /* CONFIG_SYS_NO_FLASH */
#if defined(CONFIG_CMD_NAND)
puts("NAND: ");
nand_init(); /* go init the NAND */
#endif
#if defined(CONFIG_CMD_IDE)
puts("IDE: ");
ide_init();
#endif
#ifdef CONFIG_GENERIC_MMC
puts("MMC: ");
mmc_initialize(gd->bd);
#endif
/* initialize environment */
env_relocate();
#if defined(CONFIG_CMD_PCI) || defined(CONFIG_PCI)
nds32_pci_init();
#endif
/* IP Address */
gd->bd->bi_ip_addr = getenv_IPaddr("ipaddr");
stdio_init(); /* get the devices list going. */
jumptable_init();
#if defined(CONFIG_API)
/* Initialize API */
api_init();
#endif
console_init_r(); /* fully init console as a device */
#if defined(CONFIG_ARCH_MISC_INIT)
/* miscellaneous arch dependent initialisations */
arch_misc_init();
#endif
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r();
#endif
#if defined(CONFIG_USE_IRQ)
/* set up exceptions */
interrupt_init();
/* enable exceptions */
enable_interrupts();
#endif
/* Initialize from environment */
load_addr = getenv_ulong("loadaddr", 16, load_addr);
#if defined(CONFIG_CMD_NET)
s = getenv("bootfile");
if (s != NULL)
copy_filename(BootFile, s, sizeof(BootFile));
#endif
#ifdef BOARD_LATE_INIT
board_late_init();
#endif
#if defined(CONFIG_CMD_NET)
puts("Net: ");
eth_initialize(gd->bd);
#if defined(CONFIG_RESET_PHY_R)
debug("Reset Ethernet PHY\n");
reset_phy();
#endif
#endif
/* main_loop() can return to retry autoboot, if so just run it again. */
for (;;)
main_loop();
/* NOTREACHED - no way out of command loop except booting */
}
void start_arcboot(void)
{
DECLARE_GLOBAL_DATA_PTR;
static gd_t gd_data;
static bd_t bd_data;
init_fnc_t **init_fnc_ptr;
extern void *__text_end;
unsigned stage = sizeof(init_sequence)/sizeof(init_sequence[0]);
show_boot_progress(stage--);
/* Init Global Data */
gd = global_data = &gd_data;
gd->bd = &bd_data;
gd->cpu_clk=get_cpu_clk();
gd->bd->bi_boot_params=BOOT_PARAMS_OFFSET;
gd->bd->bi_memstart=PHYS_MEMORY_START;
gd->bd->bi_memsize=PHYS_MEMORY_SIZE;
gd->bd->bi_flashstart=CONFIG_SYS_FLASH_BASE;
gd->bd->bi_flashoffset=0;
/* frame buffer will sit after end of program */
gd->fb_base = TEXT_BASE;
for (init_fnc_ptr = init_sequence;*init_fnc_ptr;++init_fnc_ptr) {
show_boot_progress(stage--);
if ((*init_fnc_ptr)() != 0) {
printf("stage:%d",stage);
hang();
}
}
/* Setup malloc area */
mem_malloc_init((ulong)&_start - CONFIG_SYS_MALLOC_LEN,
CONFIG_SYS_MALLOC_LEN);
// __builtin_arc_sleep(0);
#ifdef CONFIG_CMD_NAND
puts ("NAND: ");
nand_init();
#endif
env_relocate();
stdio_init (); /* get the devices list going. */
jumptable_init();
console_init_r();
#ifdef CONFIG_MMC
mmc_initialize(&bd_data);
#endif
#ifdef CONFIG_CMD_NET
puts ("Net: ");
gd->bd->bi_ip_addr = getenv_IPaddr ("ipaddr");
// eth_io_init();
eth_initialize(gd->bd);
#if defined(CONFIG_RESET_PHY_R)
debug ("Reset Ethernet PHY\n");
reset_phy();
#endif
#endif
#if defined(CONFIG_ARCH_MISC_INIT)
/* miscellaneous arch dependent initialisations */
arch_misc_init ();
#endif
#if defined(CONFIG_MISC_INIT_R)
/* miscellaneous platform dependent initialisations */
misc_init_r ();
#endif
#if defined(CONFIG_CMD_KGDB)
puts("KGDB: ");
kgdb_init();
#endif
/* enable exceptions */
enable_interrupts ();
icache_enable();
dcache_enable();
printf("Dcache status %d\n",dcache_status());
printf("Icache status %d\n",icache_status());
#ifdef CONFIG_A3_DISPLAY
osd_display();
#endif
#ifdef CONFIG_A3_I2C
disable_i2c_pinmux();//disable hard i2c pinmux
#endif
// kgdb_test();
// init_osd_dev() ;
for(;;){
main_loop();
}
}
