void cliCom(void)
{
uint16_t index;
char mvlkToggleString[5] = { 0, 0, 0, 0, 0 };
if ((cliPortAvailable() && !validCliCommand))
{
cliQuery = cliPortRead();
if (cliQuery == '#') // Check to see if we should toggle mavlink msg state
{
while (cliPortAvailable == false);
readStringCLI(mvlkToggleString, 5);
if ((mvlkToggleString[0] == '#') &&
(mvlkToggleString[1] == '#') &&
(mvlkToggleString[2] == '#') &&
(mvlkToggleString[3] == '#'))
{
if (systemConfig.mavlinkEnabled == false)
{
systemConfig.mavlinkEnabled = true;
systemConfig.activeTelemetry = 0x0000;
}
else
{
systemConfig.mavlinkEnabled = false;
}
if (mvlkToggleString[4] == 'W')
{
cliPortPrint("\nWriting EEPROM Parameters....\n");
writeSystemEEPROM();
}
}
}
}
validCliCommand = false;
if ((systemConfig.mavlinkEnabled == false) && (cliQuery != '#'))
{
switch (cliQuery)
{
///////////////////////////////
case 'a': // Rate PIDs
cliPortPrintF("\nRoll Rate PID: %8.4f, %8.4f, %8.4f, %8.4f\n", systemConfig.PID[ROLL_RATE_PID].P,
systemConfig.PID[ROLL_RATE_PID].I,
systemConfig.PID[ROLL_RATE_PID].D,
systemConfig.PID[ROLL_RATE_PID].N);
cliPortPrintF( "Pitch Rate PID: %8.4f, %8.4f, %8.4f, %8.4f\n", systemConfig.PID[PITCH_RATE_PID].P,
systemConfig.PID[PITCH_RATE_PID].I,
systemConfig.PID[PITCH_RATE_PID].D,
systemConfig.PID[PITCH_RATE_PID].N);
cliPortPrintF( "Yaw Rate PID: %8.4f, %8.4f, %8.4f, %8.4f\n", systemConfig.PID[YAW_RATE_PID].P,
systemConfig.PID[YAW_RATE_PID].I,
systemConfig.PID[YAW_RATE_PID].D,
systemConfig.PID[YAW_RATE_PID].N);
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'b': // Attitude PIDs
cliPortPrintF("\nRoll Attitude PID: %8.4f, %8.4f, %8.4f, %8.4f\n", systemConfig.PID[ROLL_ATT_PID].P,
systemConfig.PID[ROLL_ATT_PID].I,
systemConfig.PID[ROLL_ATT_PID].D,
systemConfig.PID[ROLL_ATT_PID].N);
cliPortPrintF( "Pitch Attitude PID: %8.4f, %8.4f, %8.4f, %8.4f\n", systemConfig.PID[PITCH_ATT_PID].P,
systemConfig.PID[PITCH_ATT_PID].I,
systemConfig.PID[PITCH_ATT_PID].D,
systemConfig.PID[PITCH_ATT_PID].N);
cliPortPrintF( "Heading PID: %8.4f, %8.4f, %8.4f, %8.4f\n", systemConfig.PID[HEADING_PID].P,
systemConfig.PID[HEADING_PID].I,
systemConfig.PID[HEADING_PID].D,
systemConfig.PID[HEADING_PID].N);
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'c': // Velocity PIDs
cliPortPrintF("\nnDot PID: %8.4f, %8.4f, %8.4f, %8.4f\n", systemConfig.PID[NDOT_PID].P,
systemConfig.PID[NDOT_PID].I,
systemConfig.PID[NDOT_PID].D,
systemConfig.PID[NDOT_PID].N);
cliPortPrintF( "eDot PID: %8.4f, %8.4f, %8.4f, %8.4f\n", systemConfig.PID[EDOT_PID].P,
systemConfig.PID[EDOT_PID].I,
systemConfig.PID[EDOT_PID].D,
systemConfig.PID[EDOT_PID].N);
cliPortPrintF( "hDot PID: %8.4f, %8.4f, %8.4f, %8.4f\n", systemConfig.PID[HDOT_PID].P,
systemConfig.PID[HDOT_PID].I,
systemConfig.PID[HDOT_PID].D,
systemConfig.PID[HDOT_PID].N);
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'd': // Position PIDs
cliPortPrintF("\nN PID: %8.4f, %8.4f, %8.4f, %8.4f\n", systemConfig.PID[N_PID].P,
systemConfig.PID[N_PID].I,
systemConfig.PID[N_PID].D,
systemConfig.PID[N_PID].N);
cliPortPrintF( "E PID: %8.4f, %8.4f, %8.4f, %8.4f\n", systemConfig.PID[E_PID].P,
systemConfig.PID[E_PID].I,
systemConfig.PID[E_PID].D,
systemConfig.PID[E_PID].N);
cliPortPrintF( "h PID: %8.4f, %8.4f, %8.4f, %8.4f\n", systemConfig.PID[H_PID].P,
systemConfig.PID[H_PID].I,
systemConfig.PID[H_PID].D,
systemConfig.PID[H_PID].N);
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'e': // Loop Delta Times
cliPortPrintF("%7ld, %7ld, %7ld, %7ld, %7ld, %7ld, %7ld\n", deltaTime1000Hz,
deltaTime500Hz,
deltaTime100Hz,
deltaTime50Hz,
deltaTime10Hz,
deltaTime5Hz,
deltaTime1Hz);
validCliCommand = false;
break;
///////////////////////////////
case 'f': // Loop Execution Times
cliPortPrintF("%7ld, %7ld, %7ld, %7ld, %7ld, %7ld, %7ld\n", executionTime1000Hz,
executionTime500Hz,
executionTime100Hz,
executionTime50Hz,
executionTime10Hz,
executionTime5Hz,
executionTime1Hz);
validCliCommand = false;
break;
///////////////////////////////
case 'g': // 500 Hz Accels
cliPortPrintF("%9.4f, %9.4f, %9.4f\n", sensors.accel500Hz[XAXIS],
sensors.accel500Hz[YAXIS],
sensors.accel500Hz[ZAXIS]);
validCliCommand = false;
break;
///////////////////////////////
case 'h': // 100 hz Earth Axis Accels
cliPortPrintF("%9.4f, %9.4f, %9.4f\n", earthAxisAccels[XAXIS],
earthAxisAccels[YAXIS],
earthAxisAccels[ZAXIS]);
validCliCommand = false;
break;
///////////////////////////////
case 'i': // 500 hz Gyros
cliPortPrintF("%9.4f, %9.4f, %9.4f, %9.4f\n", sensors.gyro500Hz[ROLL ] * R2D,
sensors.gyro500Hz[PITCH] * R2D,
sensors.gyro500Hz[YAW ] * R2D,
mpu6000Temperature);
validCliCommand = false;
break;
///////////////////////////////
case 'j': // 10 Hz Mag Data
cliPortPrintF("%9.4f, %9.4f, %9.4f\n", sensors.mag10Hz[XAXIS],
sensors.mag10Hz[YAXIS],
sensors.mag10Hz[ZAXIS]);
validCliCommand = false;
break;
///////////////////////////////
case 'k': // Vertical Axis Variables
cliPortPrintF("%9.4f, %9.4f, %9.4f, %9.4f, %4ld, %9.4f\n", earthAxisAccels[ZAXIS],
sensors.pressureAlt50Hz,
hDotEstimate,
hEstimate,
ms5611Temperature,
aglRead());
validCliCommand = false;
break;
///////////////////////////////
case 'l': // Attitudes
cliPortPrintF("%9.4f, %9.4f, %9.4f\n", sensors.attitude500Hz[ROLL ] * R2D,
sensors.attitude500Hz[PITCH] * R2D,
sensors.attitude500Hz[YAW ] * R2D);
validCliCommand = false;
break;
///////////////////////////////
case 'm': // Axis PIDs
cliPortPrintF("%9.4f, %9.4f, %9.4f\n", ratePID[ROLL ],
ratePID[PITCH],
ratePID[YAW ]);
validCliCommand = false;
break;
///////////////////////////////
case 'n': // GPS Data
switch (gpsDataType)
{
///////////////////////
case 0:
cliPortPrintF("%12ld, %12ld, %12ld, %12ld, %12ld, %12ld, %4d, %4d\n", gps.latitude,
gps.longitude,
gps.hMSL,
gps.velN,
gps.velE,
gps.velD,
gps.fix,
gps.numSats);
break;
///////////////////////
case 1:
cliPortPrintF("%3d: ", gps.numCh);
for (index = 0; index < gps.numCh; index++)
cliPortPrintF("%3d ", gps.chn[index]);
cliPortPrint("\n");
break;
///////////////////////
case 2:
cliPortPrintF("%3d: ", gps.numCh);
for (index = 0; index < gps.numCh; index++)
cliPortPrintF("%3d ", gps.svid[index]);
cliPortPrint("\n");
break;
///////////////////////
case 3:
cliPortPrintF("%3d: ", gps.numCh);
for (index = 0; index < gps.numCh; index++)
cliPortPrintF("%3d ", gps.cno[index]);
cliPortPrint("\n");
break;
///////////////////////
}
validCliCommand = false;
break;
///////////////////////////////
case 'o':
cliPortPrintF("%9.4f\n", batteryVoltage);
validCliCommand = false;
break;
///////////////////////////////
case 'p': // Primary Spektrum Raw Data
cliPortPrintF("%04X, %04X, %04X, %04X, %04X, %04X, %04X, %04X, %04X, %04X\n", primarySpektrumState.lostFrameCnt,
primarySpektrumState.rcAvailable,
primarySpektrumState.values[0],
primarySpektrumState.values[1],
primarySpektrumState.values[2],
primarySpektrumState.values[3],
primarySpektrumState.values[4],
primarySpektrumState.values[5],
primarySpektrumState.values[6],
primarySpektrumState.values[7]);
validCliCommand = false;
break;
///////////////////////////////
case 'q': // Not Used
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'r':
if (flightMode == RATE)
cliPortPrint("Flight Mode:RATE ");
else if (flightMode == ATTITUDE)
cliPortPrint("Flight Mode:ATTITUDE ");
else if (flightMode == GPS)
cliPortPrint("Flight Mode:GPS ");
if (headingHoldEngaged == true)
cliPortPrint("Heading Hold:ENGAGED ");
else
cliPortPrint("Heading Hold:DISENGAGED ");
switch (verticalModeState)
{
case ALT_DISENGAGED_THROTTLE_ACTIVE:
cliPortPrint("Alt:Disenaged Throttle Active ");
break;
case ALT_HOLD_FIXED_AT_ENGAGEMENT_ALT:
cliPortPrint("Alt:Hold Fixed at Engagement Alt ");
break;
case ALT_HOLD_AT_REFERENCE_ALTITUDE:
cliPortPrint("Alt:Hold at Reference Alt ");
break;
case VERTICAL_VELOCITY_HOLD_AT_REFERENCE_VELOCITY:
cliPortPrint("Alt:Velocity Hold at Reference Vel ");
break;
case ALT_DISENGAGED_THROTTLE_INACTIVE:
cliPortPrint("Alt:Disengaged Throttle Inactive ");
break;
}
if (rxCommand[AUX3] > MIDCOMMAND)
cliPortPrint("Mode:Simple ");
else
cliPortPrint("Mode:Normal ");
if (rxCommand[AUX4] > MIDCOMMAND)
cliPortPrint("Emergency Bail:Active\n");
else
cliPortPrint("Emergency Bail:Inactive\n");
validCliCommand = false;
break;
///////////////////////////////
case 's': // Raw Receiver Commands
if ((systemConfig.receiverType == SPEKTRUM) && (maxChannelNum > 0))
{
for (index = 0; index < maxChannelNum - 1; index++)
cliPortPrintF("%4ld, ", spektrumBuf[index]);
cliPortPrintF("%4ld\n", spektrumBuf[maxChannelNum - 1]);
}
else if ((systemConfig.receiverType == SPEKTRUM) && (maxChannelNum == 0))
cliPortPrint("Invalid Number of Spektrum Channels....\n");
else
{
for (index = 0; index < 7; index++)
cliPortPrintF("%4i, ", ppmRxRead(index));
cliPortPrintF("%4i\n", ppmRxRead(7));
}
validCliCommand = false;
break;
///////////////////////////////
case 't': // Processed Receiver Commands
for (index = 0; index < 7; index++)
cliPortPrintF("%8.2f, ", rxCommand[index]);
cliPortPrintF("%8.2f\n", rxCommand[7]);
validCliCommand = false;
break;
///////////////////////////////
case 'u': // Command in Detent Discretes
cliPortPrintF("%s, ", commandInDetent[ROLL ] ? " true" : "false");
cliPortPrintF("%s, ", commandInDetent[PITCH] ? " true" : "false");
cliPortPrintF("%s\n", commandInDetent[YAW ] ? " true" : "false");
validCliCommand = false;
break;
///////////////////////////////
case 'v': // ESC PWM Outputs
cliPortPrintF("%4ld, ", TIM2->CCR1 );
cliPortPrintF("%4ld, ", TIM2->CCR2 );
cliPortPrintF("%4ld, ", TIM15->CCR1);
cliPortPrintF("%4ld, ", TIM15->CCR2);
cliPortPrintF("%4ld, ", TIM3->CCR1 );
cliPortPrintF("%4ld\n", TIM3->CCR2 );
validCliCommand = false;
break;
///////////////////////////////
case 'w': // Servo PWM Outputs
cliPortPrintF("%4ld, ", TIM4->CCR1);
cliPortPrintF("%4ld, ", TIM4->CCR2);
cliPortPrintF("%4ld, ", TIM4->CCR3);
cliPortPrintF("%4ld\n", TIM4->CCR4);
validCliCommand = false;
break;
///////////////////////////////
case 'x':
validCliCommand = false;
break;
///////////////////////////////
case 'y': // ESC Calibration
escCalibration();
cliQuery = 'x';
break;
///////////////////////////////
case 'z':
cliPortPrintF("%5.2f, %5.2f\n", voltageMonitor(),
adcChannel());
break;
///////////////////////////////
///////////////////////////////////////////////////////////////////////
///////////////////////////////////////////////////////////////////////
///////////////////////////////////////////////////////////////////////
///////////////////////////////////////////////////////////////////////
///////////////////////////////
case 'A': // Read Roll Rate PID Values
readCliPID(ROLL_RATE_PID);
cliPortPrint( "\nRoll Rate PID Received....\n" );
cliQuery = 'a';
validCliCommand = false;
break;
///////////////////////////////
case 'B': // Read Pitch Rate PID Values
readCliPID(PITCH_RATE_PID);
cliPortPrint( "\nPitch Rate PID Received....\n" );
cliQuery = 'a';
validCliCommand = false;
break;
///////////////////////////////
case 'C': // Read Yaw Rate PID Values
readCliPID(YAW_RATE_PID);
cliPortPrint( "\nYaw Rate PID Received....\n" );
cliQuery = 'a';
validCliCommand = false;
break;
///////////////////////////////
case 'D': // Read Roll Attitude PID Values
readCliPID(ROLL_ATT_PID);
cliPortPrint( "\nRoll Attitude PID Received....\n" );
cliQuery = 'b';
validCliCommand = false;
break;
///////////////////////////////
case 'E': // Read Pitch Attitude PID Values
readCliPID(PITCH_ATT_PID);
cliPortPrint( "\nPitch Attitude PID Received....\n" );
cliQuery = 'b';
validCliCommand = false;
break;
///////////////////////////////
case 'F': // Read Heading Hold PID Values
readCliPID(HEADING_PID);
cliPortPrint( "\nHeading PID Received....\n" );
cliQuery = 'b';
validCliCommand = false;
break;
///////////////////////////////
case 'G': // Read nDot PID Values
readCliPID(NDOT_PID);
cliPortPrint( "\nnDot PID Received....\n" );
cliQuery = 'c';
validCliCommand = false;
break;
///////////////////////////////
case 'H': // Read eDot PID Values
readCliPID(EDOT_PID);
cliPortPrint( "\neDot PID Received....\n" );
cliQuery = 'c';
validCliCommand = false;
break;
///////////////////////////////
case 'I': // Read hDot PID Values
readCliPID(HDOT_PID);
cliPortPrint( "\nhDot PID Received....\n" );
cliQuery = 'c';
validCliCommand = false;
break;
///////////////////////////////
case 'J': // Read n PID Values
readCliPID(N_PID);
cliPortPrint( "\nn PID Received....\n" );
cliQuery = 'd';
validCliCommand = false;
break;
///////////////////////////////
case 'K': // Read e PID Values
readCliPID(E_PID);
cliPortPrint( "\ne PID Received....\n" );
cliQuery = 'd';
validCliCommand = false;
break;
///////////////////////////////
case 'L': // Read h PID Values
readCliPID(H_PID);
cliPortPrint( "\nh PID Received....\n" );
cliQuery = 'd';
validCliCommand = false;
break;
///////////////////////////////
case 'N': // Mixer CLI
mixerCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'O': // Receiver CLI
receiverCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'P': // Sensor CLI
sensorCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'Q': // GPS Data Selection
gpsDataType = (uint8_t)readFloatCLI();
cliPortPrint("\n");
cliQuery = 'n';
validCliCommand = false;
break;
///////////////////////////////
case 'R': // Reset to Bootloader
cliPortPrint("Entering Bootloader....\n\n");
delay(100);
systemReset(true);
break;
///////////////////////////////
case 'S': // Reset System
cliPortPrint("\nSystem Reseting....\n\n");
delay(100);
systemReset(false);
break;
///////////////////////////////
case 'T': // Telemetry CLI
telemetryCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'U': // EEPROM CLI
eepromCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'V': // Write Sensor EEPROM Parameters
cliPortPrint("\nWriting Sensor EEPROM Parameters....\n\n");
cliBusy = true;
writeSensorEEPROM();
cliBusy = false;
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'W': // Write System EEPROM Parameters
cliPortPrint("\nWriting System EEPROM Parameters....\n\n");
cliBusy = true;
writeSystemEEPROM();
cliBusy = false;
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'X': // Not Used
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'Y': // Not Used
computeGeoMagElements();
cliQuery = 'x';
break;
///////////////////////////////
case 'Z': // Not Used
if (usbIsConfigured() == true)
cliPortPrint("\nUSB Configured TRUE\n");
else
cliPortPrint("\nUSB Configured FALSE\n");
if (usbIsConnected() == true)
cliPortPrint("\nUSB Connected TRUE\n");
else
cliPortPrint("\nUSB Connected FALSE\n");
cliQuery = 'x';
break;
///////////////////////////////
case '?': // Command Summary
cliBusy = true;
cliPortPrint("\n");
cliPortPrint("'a' Rate PIDs 'A' Set Roll Rate PID Data AB;P;I;D;windupGuard;dErrorCalc\n");
cliPortPrint("'b' Attitude PIDs 'B' Set Pitch Rate PID Data BB;P;I;D;windupGuard;dErrorCalc\n");
cliPortPrint("'c' Velocity PIDs 'C' Set Yaw Rate PID Data CB;P;I;D;windupGuard;dErrorCalc\n");
cliPortPrint("'d' Position PIDs 'D' Set Roll Att PID Data DB;P;I;D;windupGuard;dErrorCalc\n");
cliPortPrint("'e' Loop Delta Times 'E' Set Pitch Att PID Data EB;P;I;D;windupGuard;dErrorCalc\n");
cliPortPrint("'f' Loop Execution Times 'F' Set Hdg Hold PID Data FB;P;I;D;windupGuard;dErrorCalc\n");
cliPortPrint("'g' 500 Hz Accels 'G' Set nDot PID Data GB;P;I;D;windupGuard;dErrorCalc\n");
cliPortPrint("'h' 100 Hz Earth Axis Accels 'H' Set eDot PID Data HB;P;I;D;windupGuard;dErrorCalc\n");
cliPortPrint("'i' 500 Hz Gyros 'I' Set hDot PID Data IB;P;I;D;windupGuard;dErrorCalc\n");
cliPortPrint("'j' 10 hz Mag Data 'J' Set n PID Data JB;P;I;D;windupGuard;dErrorCalc\n");
cliPortPrint("'k' Vertical Axis Variable 'K' Set e PID Data KB;P;I;D;windupGuard;dErrorCalc\n");
cliPortPrint("'l' Attitudes 'L' Set h PID Data LB;P;I;D;windupGuard;dErrorCalc\n");
cliPortPrint("\n");
cliPortPrint("Press space bar for more, or enter a command....\n");
while (cliPortAvailable() == false);
cliQuery = cliPortRead();
if (cliQuery != ' ')
{
validCliCommand = true;
cliBusy = false;
return;
}
cliPortPrint("\n");
cliPortPrint("'m' Axis PIDs 'M' Not Used\n");
cliPortPrint("'n' GPS Data 'N' Mixer CLI\n");
cliPortPrint("'o' Battery Voltage 'O' Receiver CLI\n");
cliPortPrint("'p' Primary Spektrum Raw Data 'P' Sensor CLI\n");
cliPortPrint("'q' Not Used 'Q' GPS Data Selection\n");
cliPortPrint("'r' Mode States 'R' Reset and Enter Bootloader\n");
cliPortPrint("'s' Raw Receiver Commands 'S' Reset\n");
cliPortPrint("'t' Processed Receiver Commands 'T' Telemetry CLI\n");
cliPortPrint("'u' Command In Detent Discretes 'U' EEPROM CLI\n");
cliPortPrint("'v' Motor PWM Outputs 'V' Write Sensor EEPROM Parameters\n");
cliPortPrint("'w' Servo PWM Outputs 'W' Write System EEPROM Parameters\n");
cliPortPrint("'x' Terminate Serial Communication 'X' Not Used\n");
cliPortPrint("\n");
cliPortPrint("Press space bar for more, or enter a command....\n");
while (cliPortAvailable() == false);
cliQuery = cliPortRead();
if (cliQuery != ' ')
{
validCliCommand = true;
cliBusy = false;
return;
}
cliPortPrint("\n");
cliPortPrint("'y' ESC Calibration 'Y' Not Used\n");
cliPortPrint("'z' ADC Values 'Z' Not Used\n");
cliPortPrint(" '?' Command Summary\n");
cliPortPrint("\n");
cliQuery = 'x';
cliBusy = false;
break;
///////////////////////////////
}
}
}
void cliCom(void)
{
uint8_t i2cReadBuff; // TEMP
uint8_t index;
uint8_t numChannels = 8;
char mvlkToggleString[5] = { 0, 0, 0, 0, 0 };
if (eepromConfig.receiverType == PPM)
numChannels = eepromConfig.ppmChannels;
if ((cliPortAvailable() && !validCliCommand))
{
// Pull one character from buffer to find command
cliQuery = cliPortRead();
// Check to see if we should toggle MAVLink state (pound sign)
if (cliQuery == '#')
{
while (cliPortAvailable == false);
// Check to see if we have 4 pound signs
readStringCLI(mvlkToggleString, 5);
if ((mvlkToggleString[0] == '#') &&
(mvlkToggleString[1] == '#') &&
(mvlkToggleString[2] == '#') &&
(mvlkToggleString[3] == '#'))
{
// Toggle MAVLink
if (eepromConfig.mavlinkEnabled == false)
eepromConfig.mavlinkEnabled = true;
else
eepromConfig.mavlinkEnabled = false;
// Write EEPROM state if pounds were followed by W
if (mvlkToggleString[4] == 'W')
{
cliPortPrint("\nWriting EEPROM Parameters....\n");
writeEEPROM();
}
}
}
}
validCliCommand = false;
// If MAVLink is disabled and we aren't toggling MAVLink, assume CLI command
if ((eepromConfig.mavlinkEnabled == false) && (cliQuery != '#'))
{
switch (cliQuery)
{
///////////////////////////////
case 'a': // Rate PIDs
cliPortPrintF("\nRoll Rate PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[ROLL_RATE_PID].P,
eepromConfig.PID[ROLL_RATE_PID].I,
eepromConfig.PID[ROLL_RATE_PID].D,
eepromConfig.PID[ROLL_RATE_PID].Limit);
cliPortPrintF( "Pitch Rate PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[PITCH_RATE_PID].P,
eepromConfig.PID[PITCH_RATE_PID].I,
eepromConfig.PID[PITCH_RATE_PID].D,
eepromConfig.PID[PITCH_RATE_PID].Limit);
cliPortPrintF( "Yaw Rate PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[YAW_RATE_PID].P,
eepromConfig.PID[YAW_RATE_PID].I,
eepromConfig.PID[YAW_RATE_PID].D,
eepromConfig.PID[YAW_RATE_PID].Limit);
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'b': // Attitude PIDs
cliPortPrintF("\nRoll Attitude PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[ROLL_ATT_PID].P,
eepromConfig.PID[ROLL_ATT_PID].I,
eepromConfig.PID[ROLL_ATT_PID].D,
eepromConfig.PID[ROLL_ATT_PID].Limit);
cliPortPrintF( "Pitch Attitude PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[PITCH_ATT_PID].P,
eepromConfig.PID[PITCH_ATT_PID].I,
eepromConfig.PID[PITCH_ATT_PID].D,
eepromConfig.PID[PITCH_ATT_PID].Limit);
cliPortPrintF( "Heading PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[HEADING_PID].P,
eepromConfig.PID[HEADING_PID].I,
eepromConfig.PID[HEADING_PID].D,
eepromConfig.PID[HEADING_PID].Limit);
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'c': // Velocity PIDs
cliPortPrintF("\nnDot PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[NDOT_PID].P,
eepromConfig.PID[NDOT_PID].I,
eepromConfig.PID[NDOT_PID].D,
eepromConfig.PID[NDOT_PID].Limit);
cliPortPrintF( "eDot PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[EDOT_PID].P,
eepromConfig.PID[EDOT_PID].I,
eepromConfig.PID[EDOT_PID].D,
eepromConfig.PID[EDOT_PID].Limit);
cliPortPrintF( "hDot PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[HDOT_PID].P,
eepromConfig.PID[HDOT_PID].I,
eepromConfig.PID[HDOT_PID].D,
eepromConfig.PID[HDOT_PID].Limit);
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'd': // Position PIDs
cliPortPrintF("\nN PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[N_PID].P,
eepromConfig.PID[N_PID].I,
eepromConfig.PID[N_PID].D,
eepromConfig.PID[N_PID].Limit);
cliPortPrintF( "E PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[E_PID].P,
eepromConfig.PID[E_PID].I,
eepromConfig.PID[E_PID].D,
eepromConfig.PID[E_PID].Limit);
cliPortPrintF( "h PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[H_PID].P,
eepromConfig.PID[H_PID].I,
eepromConfig.PID[H_PID].D,
eepromConfig.PID[H_PID].Limit);
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'e': // Loop Delta Times
cliPortPrintF("%7ld, %7ld, %7ld, %7ld, %7ld, %7ld, %7ld\n", deltaTime1000Hz,
deltaTime500Hz,
deltaTime100Hz,
deltaTime50Hz,
deltaTime10Hz,
deltaTime5Hz,
deltaTime1Hz);
validCliCommand = false;
break;
///////////////////////////////
case 'f': // Loop Execution Times
cliPortPrintF("%7ld, %7ld, %7ld, %7ld, %7ld, %7ld, %7ld\n", executionTime1000Hz,
executionTime500Hz,
executionTime100Hz,
executionTime50Hz,
executionTime10Hz,
executionTime5Hz,
executionTime1Hz);
validCliCommand = false;
break;
///////////////////////////////
case 'g': // 100 Hz Accels
cliPortPrintF("%9.4f, %9.4f, %9.4f\n", sensors.accel100Hz[XAXIS],
sensors.accel100Hz[YAXIS],
sensors.accel100Hz[ZAXIS]);
validCliCommand = false;
break;
///////////////////////////////
case 'h': // 100 hz Earth Axis Accels
cliPortPrintF("%9.4f, %9.4f, %9.4f\n", earthAxisAccels[XAXIS],
earthAxisAccels[YAXIS],
earthAxisAccels[ZAXIS]);
validCliCommand = false;
break;
///////////////////////////////
case 'i': // 500 hz Gyros
cliPortPrintF("%9.4f, %9.4f, %9.4f, %9.4f\n", sensors.gyro500Hz[ROLL ] * R2D,
sensors.gyro500Hz[PITCH] * R2D,
sensors.gyro500Hz[YAW ] * R2D,
mpu6000Temperature);
validCliCommand = false;
break;
///////////////////////////////
case 'j': // 10 Hz Mag Data
cliPortPrintF("%9.4f, %9.4f, %9.4f\n", sensors.mag10Hz[XAXIS],
sensors.mag10Hz[YAXIS],
sensors.mag10Hz[ZAXIS]);
validCliCommand = false;
break;
///////////////////////////////
case 'k': // Vertical Axis Variables
cliPortPrintF("%9.4f, %9.4f, %9.4f, %9.4f, %4ld, %9.4f\n", earthAxisAccels[ZAXIS],
sensors.pressureAlt50Hz,
hDotEstimate,
hEstimate,
ms5611Temperature,
aglRead());
validCliCommand = false;
break;
///////////////////////////////
case 'l': // Attitudes
cliPortPrintF("%9.4f, %9.4f, %9.4f\n", sensors.attitude500Hz[ROLL ] * R2D,
sensors.attitude500Hz[PITCH] * R2D,
sensors.attitude500Hz[YAW ] * R2D);
validCliCommand = false;
break;
///////////////////////////////
case 'm': // Axis PIDs
cliPortPrintF("%9.4f, %9.4f, %9.4f\n", ratePID[ROLL ],
ratePID[PITCH],
ratePID[YAW ]);
validCliCommand = false;
break;
///////////////////////////////
case 'n': // GPS Data
cliPortPrintF("ITOW:%12ld, LAT:%12ld, LONG:%12ld, HEAD:%12ld, HEIGHT:%12ld, HMSL:%12ld, FIX:%4d, NUMSAT:%4d\n",
gps.iTOW,
gps.latitude,
gps.longitude,
gps.hDop,
gps.height,
gps.hMSL,
gps.fix,
gps.numSats);
validCliCommand = false;
break;
///////////////////////////////
case 'o':
cliPortPrintF("%9.4f\n", batteryVoltage);
validCliCommand = false;
break;
///////////////////////////////
case 'p':
cameraCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'q':
adcCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////FLIGHT MODE
case 'r':
if (flightMode == RATE)
cliPortPrint("Flight Mode:RATE ");
else if (flightMode == ATTITUDE)
cliPortPrint("Flight Mode:ATTITUDE ");
else if (flightMode == GPS)
cliPortPrint("Flight Mode:GPS ");
if (headingHoldEngaged == true)
cliPortPrint("Heading Hold:ENGAGED ");
else
cliPortPrint("Heading Hold:DISENGAGED ");
switch (verticalModeState)
{
case ALT_DISENGAGED_THROTTLE_ACTIVE:
cliPortPrint("Alt:Disenaged Throttle Active ");
break;
case ALT_HOLD_FIXED_AT_ENGAGEMENT_ALT:
cliPortPrint("Alt:Hold Fixed at Engagement Alt ");
break;
case ALT_HOLD_AT_REFERENCE_ALTITUDE:
cliPortPrint("Alt:Hold at Reference Alt ");
break;
case VERTICAL_VELOCITY_HOLD_AT_REFERENCE_VELOCITY:
cliPortPrint("Alt:Velocity Hold at Reference Vel ");
break;
case ALT_DISENGAGED_THROTTLE_INACTIVE:
cliPortPrint("Alt:Disengaged Throttle Inactive ");
break;
}
if (rxCommand[AUX3] > MIDCOMMAND)
cliPortPrint("Mode:Simple ");
else
cliPortPrint("Mode:Normal ");
if (rxCommand[AUX4] > MIDCOMMAND)
cliPortPrint("Emergency Bail:Active\n");
else
cliPortPrint("Emergency Bail:Inactive\n");
validCliCommand = false;
break;
///////////////////////////////
case 's': // Raw Receiver Commands
if ((eepromConfig.receiverType == SPEKTRUM) && (maxChannelNum > 0))
{
for (index = 0; index < maxChannelNum - 1; index++)
cliPortPrintF("%4ld, ", spektrumBuf[index]);
cliPortPrintF("%4ld\n", spektrumBuf[maxChannelNum - 1]);
}
else if (eepromConfig.receiverType == SBUS)
{
for (index = 0; index < 7; index++)
cliPortPrintF("%4ld, ", sBusRead(index));
cliPortPrintF("%4ld\n", sBusRead(7));
}
else
{
for (index = 0; index < numChannels - 1; index++)
cliPortPrintF("%4i, ", Inputs[index].pulseWidth);
cliPortPrintF("%4i\n", Inputs[numChannels - 1].pulseWidth);
}
validCliCommand = false;
break;
///////////////////////////////
case 't': // Processed Receiver Commands
for (index = 0; index < numChannels - 1; index++)
cliPortPrintF("%8.2f, ", rxCommand[index]);
cliPortPrintF("%8.2f\n", rxCommand[numChannels - 1]);
validCliCommand = false;
break;
///////////////////////////////
case 'u': // Command in Detent Discretes
cliPortPrintF("%s, ", commandInDetent[ROLL ] ? " true" : "false");
cliPortPrintF("%s, ", commandInDetent[PITCH] ? " true" : "false");
cliPortPrintF("%s\n", commandInDetent[YAW ] ? " true" : "false");
validCliCommand = false;
break;
///////////////////////////////
case 'v': // ESC PWM Outputs
cliPortPrintF("%4ld, ", TIM8->CCR4);
cliPortPrintF("%4ld, ", TIM8->CCR3);
cliPortPrintF("%4ld, ", TIM8->CCR2);
cliPortPrintF("%4ld, ", TIM8->CCR1);
cliPortPrintF("%4ld, ", TIM2->CCR1);
cliPortPrintF("%4ld, ", TIM2->CCR2);
cliPortPrintF("%4ld, ", TIM3->CCR1);
cliPortPrintF("%4ld\n", TIM3->CCR2);
validCliCommand = false;
break;
///////////////////////////////
case 'w': // Servo PWM Outputs
cliPortPrintF("%4ld, ", TIM5->CCR3);
cliPortPrintF("%4ld, ", TIM5->CCR2);
cliPortPrintF("%4ld\n", TIM5->CCR1);
validCliCommand = false;
break;
///////////////////////////////
case 'x':
validCliCommand = false;
break;
///////////////////////////////
case 'y': // ESC Calibration
escCalibration();
cliQuery = 'x';
break;
///////////////////////////////
case 'z': // ADC readings
cliPortPrintF("%8.4f, %8.4f, %8.4f, %8.4f, %8.4f, %8.4f, %8.4f\n", adcValue(1),
adcValue(2),
adcValue(3),
adcValue(4),
adcValue(5),
adcValue(6),
adcValue(7));
break;
///////////////////////////////
///////////////////////////////////////////////////////////////////////
///////////////////////////////////////////////////////////////////////
///////////////////////////////////////////////////////////////////////
///////////////////////////////////////////////////////////////////////
///////////////////////////////
case 'A': // Read Roll Rate PID Values
readCliPID(ROLL_RATE_PID);
cliPortPrint( "\nRoll Rate PID Received....\n" );
cliQuery = 'a';
validCliCommand = false;
break;
///////////////////////////////
case 'B': // Read Pitch Rate PID Values
readCliPID(PITCH_RATE_PID);
cliPortPrint( "\nPitch Rate PID Received....\n" );
cliQuery = 'a';
validCliCommand = false;
break;
///////////////////////////////
case 'C': // Read Yaw Rate PID Values
readCliPID(YAW_RATE_PID);
cliPortPrint( "\nYaw Rate PID Received....\n" );
cliQuery = 'a';
validCliCommand = false;
break;
///////////////////////////////
case 'D': // Read Roll Attitude PID Values
readCliPID(ROLL_ATT_PID);
cliPortPrint( "\nRoll Attitude PID Received....\n" );
cliQuery = 'b';
validCliCommand = false;
break;
///////////////////////////////
case 'E': // Read Pitch Attitude PID Values
readCliPID(PITCH_ATT_PID);
cliPortPrint( "\nPitch Attitude PID Received....\n" );
cliQuery = 'b';
validCliCommand = false;
break;
///////////////////////////////
case 'F': // Read Heading Hold PID Values
readCliPID(HEADING_PID);
cliPortPrint( "\nHeading PID Received....\n" );
cliQuery = 'b';
validCliCommand = false;
break;
///////////////////////////////
case 'G': // Read nDot PID Values
readCliPID(NDOT_PID);
cliPortPrint( "\nnDot PID Received....\n" );
cliQuery = 'c';
validCliCommand = false;
break;
///////////////////////////////
case 'H': // Read eDot PID Values
readCliPID(EDOT_PID);
cliPortPrint( "\neDot PID Received....\n" );
cliQuery = 'c';
validCliCommand = false;
break;
///////////////////////////////
case 'I': // Read hDot PID Values
readCliPID(HDOT_PID);
cliPortPrint( "\nhDot PID Received....\n" );
cliQuery = 'c';
validCliCommand = false;
break;
///////////////////////////////
case 'J': // Read n PID Values
readCliPID(N_PID);
cliPortPrint( "\nn PID Received....\n" );
cliQuery = 'd';
validCliCommand = false;
break;
///////////////////////////////
case 'K': // Read e PID Values
readCliPID(E_PID);
cliPortPrint( "\ne PID Received....\n" );
cliQuery = 'd';
validCliCommand = false;
break;
///////////////////////////////
case 'L': // Read h PID Values
readCliPID(H_PID);
cliPortPrint( "\nh PID Received....\n" );
cliQuery = 'd';
validCliCommand = false;
break;
///////////////////////////////
case 'M': // MAX7456 CLI
max7456CLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'N': // Mixer CLI
mixerCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'O': // Receiver CLI
receiverCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'P': // Sensor CLI
sensorCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'Q': // GPS Type Selection
cliBusy = true;
eepromConfig.gpsType = (uint8_t)readFloatCLI();
switch(eepromConfig.gpsType) {
case NO_GPS:
cliPortPrint("GPS Module Disabled\n");
break;
case MEDIATEK_3329_BINARY:
cliPortPrint("GPS Module set to MEDIATEK3329 (Binary)\n");
break;
case MEDIATEK_3329_NMEA:
cliPortPrint("GPS Module set to MEDIATEK3329 (NMEA)\n");
break;
case UBLOX:
cliPortPrint("GPS Module set to UBLOX\n");
break;
default:
cliPortPrint("Invalid GPS module type. Use 0-3 (NONE, MEDIATEK BINARY, MEDIATEK NMEA, UBLOX\n");
break;
}
initGPS();
cliBusy = false;
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'R': // Reset to Bootloader
cliPortPrint("Entering Bootloader....\n\n");
delay(100);
systemReset(true);
break;
///////////////////////////////
case 'S': // Reset System
cliPortPrint("\nSystem Reseting....\n\n");
delay(100);
systemReset(false);
break;
///////////////////////////////
case 'T': // Telemetry CLI
telemetryCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'U': // EEPROM CLI
eepromCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'V': // Reset EEPROM Parameters
cliPortPrint( "\nEEPROM Parameters Reset....\n" );
checkFirstTime(true);
cliPortPrint("\nSystem Resetting....\n\n");
delay(100);
systemReset(false);
break;
///////////////////////////////
case 'W': // Write EEPROM Parameters
cliPortPrint("\nWriting EEPROM Parameters....\n");
writeEEPROM();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'X': // Environmental Sensor Bus CLI
esbCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'Y': // ADC CLI
adcCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'Z': // Not Used
computeGeoMagElements();
cliQuery = 'x';
break;
///////////////////////////////
case '?': // Command Summary
cliBusy = true;
cliPortPrint("\n");
cliPortPrint("'a' Rate PIDs 'A' Set Roll Rate PID Data AP;I;D;N\n");
cliPortPrint("'b' Attitude PIDs 'B' Set Pitch Rate PID Data BP;I;D;N\n");
cliPortPrint("'c' Velocity PIDs 'C' Set Yaw Rate PID Data CP;I;D;N\n");
cliPortPrint("'d' Position PIDs 'D' Set Roll Att PID Data DP;I;D;N\n");
cliPortPrint("'e' Loop Delta Times 'E' Set Pitch Att PID Data EP;I;D;N\n");
cliPortPrint("'f' Loop Execution Times 'F' Set Hdg Hold PID Data FP;I;D;N\n");
cliPortPrint("'g' 500 Hz Accels 'G' Set nDot PID Data GP;I;D;N\n");
cliPortPrint("'h' 100 Hz Earth Axis Accels 'H' Set eDot PID Data HP;I;D;N\n");
cliPortPrint("'i' 500 Hz Gyros 'I' Set hDot PID Data IP;I;D;N\n");
cliPortPrint("'j' 10 hz Mag Data 'J' Set n PID Data JP;I;D;N\n");
cliPortPrint("'k' Vertical Axis Variable 'K' Set e PID Data KP;I;D;N\n");
cliPortPrint("'l' Attitudes 'L' Set h PID Data LP;I;D;N\n");
cliPortPrint("'m' Axis PIDs 'M' MAX7456 CLI\n");
cliPortPrint("'n' GPS Data 'N' Mixer CLI\n");
cliPortPrint("'o' Battery Voltage 'O' Receiver CLI\n");
cliPortPrint("'p' Camera CLI 'P' Sensor CLI\n");
cliPortPrint("'q' ADC CLI 'Q' GPS Data Selection\n");
cliPortPrint("'r' Mode States 'R' Reset and Enter Bootloader\n");
cliPortPrint("'s' Raw Receiver Commands 'S' Reset\n");
cliPortPrint("'t' Processed Receiver Commands 'T' Telemetry CLI\n");
cliPortPrint("'u' Command In Detent Discretes 'U' EEPROM CLI\n");
cliPortPrint("'v' Motor PWM Outputs 'V' Reset EEPROM Parameters\n");
cliPortPrint("'w' Servo PWM Outputs 'W' Write EEPROM Parameters\n");
cliPortPrint("'x' Terminate Serial Communication 'X' ESB CLI\n");
cliPortPrint("'y' ESC Calibration/Motor Verification 'Y' ADC CLI\n");
cliPortPrint("'z' ADC Values 'Z' WMM Test\n");
cliPortPrint(" '?' Command Summary\n");
cliPortPrint("\n");
cliQuery = 'x';
cliBusy = false;
break;
///////////////////////////////
}
}
}
void cliCom(void)
{
uint8_t index;
char mvlkToggleString[5] = { 0, 0, 0, 0, 0 };
if ((cliPortAvailable() && !validCliCommand))
{
cliQuery = cliPortRead();
if (cliQuery == '#') // Check to see if we should toggle mavlink msg state
{
while (cliPortAvailable == false);
readStringCLI(mvlkToggleString, 5);
if ((mvlkToggleString[0] == '#') &&
(mvlkToggleString[1] == '#') &&
(mvlkToggleString[2] == '#') &&
(mvlkToggleString[3] == '#'))
{
if (eepromConfig.mavlinkEnabled == false)
{
eepromConfig.mavlinkEnabled = true;
eepromConfig.activeTelemetry = 0x0000;
}
else
{
eepromConfig.mavlinkEnabled = false;
}
if (mvlkToggleString[4] == 'W')
{
cliPortPrint("\nWriting EEPROM Parameters....\n");
writeEEPROM();
}
}
}
}
validCliCommand = false;
if ((eepromConfig.mavlinkEnabled == false) && (cliQuery != '#'))
{
switch (cliQuery)
{
///////////////////////////////
case 'a': // Rate PIDs
cliPortPrintF("\nRoll Rate PID: %8.4f, %8.4f, %8.4f, %8.4f, %8.4f, %s\n", eepromConfig.PID[ROLL_RATE_PID].B,
eepromConfig.PID[ROLL_RATE_PID].P,
eepromConfig.PID[ROLL_RATE_PID].I,
eepromConfig.PID[ROLL_RATE_PID].D,
eepromConfig.PID[ROLL_RATE_PID].windupGuard,
eepromConfig.PID[ROLL_RATE_PID].dErrorCalc ? "Error" : "State");
cliPortPrintF("Pitch Rate PID: %8.4f, %8.4f, %8.4f, %8.4f, %8.4f, %s\n", eepromConfig.PID[PITCH_RATE_PID].B,
eepromConfig.PID[PITCH_RATE_PID].P,
eepromConfig.PID[PITCH_RATE_PID].I,
eepromConfig.PID[PITCH_RATE_PID].D,
eepromConfig.PID[PITCH_RATE_PID].windupGuard,
eepromConfig.PID[PITCH_RATE_PID].dErrorCalc ? "Error" : "State");
cliPortPrintF("Yaw Rate PID: %8.4f, %8.4f, %8.4f, %8.4f, %8.4f, %s\n", eepromConfig.PID[YAW_RATE_PID].B,
eepromConfig.PID[YAW_RATE_PID].P,
eepromConfig.PID[YAW_RATE_PID].I,
eepromConfig.PID[YAW_RATE_PID].D,
eepromConfig.PID[YAW_RATE_PID].windupGuard,
eepromConfig.PID[YAW_RATE_PID].dErrorCalc ? "Error" : "State");
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'b': // Attitude PIDs
cliPortPrintF("\nRoll Attitude PID: %8.4f, %8.4f, %8.4f, %8.4f, %8.4f, %s\n", eepromConfig.PID[ROLL_ATT_PID].B,
eepromConfig.PID[ROLL_ATT_PID].P,
eepromConfig.PID[ROLL_ATT_PID].I,
eepromConfig.PID[ROLL_ATT_PID].D,
eepromConfig.PID[ROLL_ATT_PID].windupGuard,
eepromConfig.PID[ROLL_ATT_PID].dErrorCalc ? "Error" : "State");
cliPortPrintF("Pitch Attitude PID: %8.4f, %8.4f, %8.4f, %8.4f, %8.4f, %s\n", eepromConfig.PID[PITCH_ATT_PID].B,
eepromConfig.PID[PITCH_ATT_PID].P,
eepromConfig.PID[PITCH_ATT_PID].I,
eepromConfig.PID[PITCH_ATT_PID].D,
eepromConfig.PID[PITCH_ATT_PID].windupGuard,
eepromConfig.PID[PITCH_ATT_PID].dErrorCalc ? "Error" : "State");
cliPortPrintF("Heading PID: %8.4f, %8.4f, %8.4f, %8.4f, %8.4f, %s\n", eepromConfig.PID[HEADING_PID].B,
eepromConfig.PID[HEADING_PID].P,
eepromConfig.PID[HEADING_PID].I,
eepromConfig.PID[HEADING_PID].D,
eepromConfig.PID[HEADING_PID].windupGuard,
eepromConfig.PID[HEADING_PID].dErrorCalc ? "Error" : "State");
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'c': // Velocity PIDs
cliPortPrintF("\nhDot PID: %8.4f, %8.4f, %8.4f, %8.4f, %8.4f, %s\n", eepromConfig.PID[HDOT_PID].B,
eepromConfig.PID[HDOT_PID].P,
eepromConfig.PID[HDOT_PID].I,
eepromConfig.PID[HDOT_PID].D,
eepromConfig.PID[HDOT_PID].windupGuard,
eepromConfig.PID[HDOT_PID].dErrorCalc ? "Error" : "State");
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'd': // Position PIDs
cliPortPrintF("\nh PID: %8.4f, %8.4f, %8.4f, %8.4f, %8.4f, %s\n", eepromConfig.PID[H_PID].B,
eepromConfig.PID[H_PID].P,
eepromConfig.PID[H_PID].I,
eepromConfig.PID[H_PID].D,
eepromConfig.PID[H_PID].windupGuard,
eepromConfig.PID[H_PID].dErrorCalc ? "Error" : "State");
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'e': // Loop Delta Times
cliPortPrintF("%7ld, %7ld, %7ld, %7ld, %7ld, %7ld, %7ld\n", deltaTime1000Hz,
deltaTime500Hz,
deltaTime100Hz,
deltaTime50Hz,
deltaTime10Hz,
deltaTime5Hz,
deltaTime1Hz);
validCliCommand = false;
break;
///////////////////////////////
case 'f': // Loop Execution Times
cliPortPrintF("%7ld, %7ld, %7ld, %7ld, %7ld, %7ld, %7ld\n", executionTime1000Hz,
executionTime500Hz,
executionTime100Hz,
executionTime50Hz,
executionTime10Hz,
executionTime5Hz,
executionTime1Hz);
validCliCommand = false;
break;
///////////////////////////////
case 'g': // 500 Hz Accels
cliPortPrintF("%9.4f, %9.4f, %9.4f\n", sensors.accel500Hz[XAXIS],
sensors.accel500Hz[YAXIS],
sensors.accel500Hz[ZAXIS]);
validCliCommand = false;
break;
///////////////////////////////
case 'h': // 100 hz Earth Axis Accels
cliPortPrintF("%9.4f, %9.4f, %9.4f\n", earthAxisAccels[XAXIS],
earthAxisAccels[YAXIS],
earthAxisAccels[ZAXIS]);
validCliCommand = false;
break;
///////////////////////////////
case 'i': // 500 hz Gyros
cliPortPrintF("%9.4f, %9.4f, %9.4f, %9.4f\n", sensors.gyro500Hz[ROLL ] * R2D,
sensors.gyro500Hz[PITCH] * R2D,
sensors.gyro500Hz[YAW ] * R2D,
mpuTemperature);
validCliCommand = false;
break;
///////////////////////////////
case 'j': // 10 Hz Mag Data
cliPortPrintF("%9.4f, %9.4f, %9.4f\n", sensors.mag10Hz[XAXIS],
sensors.mag10Hz[YAXIS],
sensors.mag10Hz[ZAXIS]);
validCliCommand = false;
break;
///////////////////////////////
case 'k': // Vertical Axis Variables
cliPortPrintF("%9.4f, %9.4f, %9.4f, %9.4f\n", earthAxisAccels[ZAXIS],
sensors.pressureAlt50Hz,
hDotEstimate,
hEstimate);
validCliCommand = false;
break;
///////////////////////////////
case 'l': // Attitudes
cliPortPrintF("%9.4f, %9.4f, %9.4f\n", sensors.attitude500Hz[ROLL ] * R2D,
sensors.attitude500Hz[PITCH] * R2D,
sensors.attitude500Hz[YAW ] * R2D);
validCliCommand = false;
break;
///////////////////////////////
case 'm': // Axis PIDs
cliPortPrintF("%9.4f, %9.4f, %9.4f\n", axisPID[ROLL ],
axisPID[PITCH],
axisPID[YAW ]);
validCliCommand = false;
break;
///////////////////////////////
case 'o':
cliPortPrintF("%9.4f\n", batteryVoltage);
validCliCommand = false;
break;
///////////////////////////////
case 'p': // Primary Spektrum Raw Data
cliPortPrintF("%04X, %04X, %04X, %04X, %04X, %04X, %04X, %04X, %04X, %04X\n", primarySpektrumState.lostFrameCnt,
primarySpektrumState.rcAvailable,
primarySpektrumState.values[0],
primarySpektrumState.values[1],
primarySpektrumState.values[2],
primarySpektrumState.values[3],
primarySpektrumState.values[4],
primarySpektrumState.values[5],
primarySpektrumState.values[6],
primarySpektrumState.values[7]);
validCliCommand = false;
break;
///////////////////////////////
case 'q': // Not Used
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'r':
if (flightMode == RATE)
cliPortPrint("Flight Mode = RATE ");
else if (flightMode == ATTITUDE)
cliPortPrint("Flight Mode = ATTITUDE ");
if (headingHoldEngaged == true)
cliPortPrint("Heading Hold = ENGAGED ");
else
cliPortPrint("Heading Hold = DISENGAGED ");
cliPortPrint("Alt Hold = ");
switch (verticalModeState)
{
case ALT_DISENGAGED_THROTTLE_ACTIVE:
cliPortPrint("Alt Disenaged Throttle Active\n");
break;
case ALT_HOLD_FIXED_AT_ENGAGEMENT_ALT:
cliPortPrint("Alt Hold Fixed at Engagement Alt\n");
break;
case ALT_HOLD_AT_REFERENCE_ALTITUDE:
cliPortPrint("Alt Hold at Reference Alt\n");
break;
case VERTICAL_VELOCITY_HOLD_AT_REFERENCE_VELOCITY:
cliPortPrint("V Velocity Hold at Reference Vel\n");
break;
case ALT_DISENGAGED_THROTTLE_INACTIVE:
cliPortPrint("Alt Disengaged Throttle Inactive\n");
break;
}
validCliCommand = false;
break;
///////////////////////////////
case 's': // Raw Receiver Commands
if ((eepromConfig.receiverType == SPEKTRUM) && (maxChannelNum > 0))
{
for (index = 0; index < maxChannelNum - 1; index++)
cliPortPrintF("%4ld, ", spektrumBuf[index]);
cliPortPrintF("%4ld\n", spektrumBuf[maxChannelNum - 1]);
}
else if ((eepromConfig.receiverType == SPEKTRUM) && (maxChannelNum == 0))
cliPortPrint("Invalid Number of Spektrum Channels....\n");
else
{
for (index = 0; index < 7; index++)
cliPortPrintF("%4i, ", ppmRxRead(index));
cliPortPrintF("%4i\n", ppmRxRead(7));
}
validCliCommand = false;
break;
///////////////////////////////
case 't': // Processed Receiver Commands
for (index = 0; index < 7; index++)
cliPortPrintF("%8.2f, ", rxCommand[index]);
cliPortPrintF("%8.2f\n", rxCommand[7]);
validCliCommand = false;
break;
///////////////////////////////
case 'u': // Command in Detent Discretes
cliPortPrintF("%s, ", commandInDetent[ROLL ] ? " true" : "false");
cliPortPrintF("%s, ", commandInDetent[PITCH] ? " true" : "false");
cliPortPrintF("%s\n", commandInDetent[YAW ] ? " true" : "false");
validCliCommand = false;
break;
///////////////////////////////
case 'v': // ESC PWM Outputs
cliPortPrintF("%4ld, ", TIM4->CCR4);
cliPortPrintF("%4ld, ", TIM4->CCR3);
cliPortPrintF("%4ld, ", TIM4->CCR2);
cliPortPrintF("%4ld, ", TIM4->CCR1);
cliPortPrintF("%4ld, ", TIM1->CCR4);
cliPortPrintF("%4ld\n", TIM1->CCR1);
validCliCommand = false;
break;
///////////////////////////////
case 'x':
validCliCommand = false;
break;
///////////////////////////////
case 'y': // ESC Calibration
escCalibration();
cliQuery = 'x';
break;
///////////////////////////////
case 'z': // Voltage monitor ADC, Battery voltage
cliPortPrintF("%7.2f, %5.2f\n", voltageMonitor(), batteryVoltage);
break;
///////////////////////////////
///////////////////////////////////////////////////////////////////////
///////////////////////////////////////////////////////////////////////
///////////////////////////////////////////////////////////////////////
///////////////////////////////////////////////////////////////////////
///////////////////////////////
case 'A': // Read Roll Rate PID Values
readCliPID(ROLL_RATE_PID);
cliPortPrint( "\nRoll Rate PID Received....\n" );
cliQuery = 'a';
validCliCommand = false;
break;
///////////////////////////////
case 'B': // Read Pitch Rate PID Values
readCliPID(PITCH_RATE_PID);
cliPortPrint( "\nPitch Rate PID Received....\n" );
cliQuery = 'a';
validCliCommand = false;
break;
///////////////////////////////
case 'C': // Read Yaw Rate PID Values
readCliPID(YAW_RATE_PID);
cliPortPrint( "\nYaw Rate PID Received....\n" );
cliQuery = 'a';
validCliCommand = false;
break;
///////////////////////////////
case 'D': // Read Roll Attitude PID Values
readCliPID(ROLL_ATT_PID);
cliPortPrint( "\nRoll Attitude PID Received....\n" );
cliQuery = 'b';
validCliCommand = false;
break;
///////////////////////////////
case 'E': // Read Pitch Attitude PID Values
readCliPID(PITCH_ATT_PID);
cliPortPrint( "\nPitch Attitude PID Received....\n" );
cliQuery = 'b';
validCliCommand = false;
break;
///////////////////////////////
case 'F': // Read Heading Hold PID Values
readCliPID(HEADING_PID);
cliPortPrint( "\nHeading PID Received....\n" );
cliQuery = 'b';
validCliCommand = false;
break;
///////////////////////////////
case 'I': // Read hDot PID Values
readCliPID(HDOT_PID);
cliPortPrint( "\nhDot PID Received....\n" );
cliQuery = 'c';
validCliCommand = false;
break;
///////////////////////////////
case 'L': // Read h PID Values
readCliPID(H_PID);
cliPortPrint( "\nh PID Received....\n" );
cliQuery = 'd';
validCliCommand = false;
break;
///////////////////////////////
case 'N': // Mixer CLI
mixerCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'O': // Receiver CLI
receiverCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'P': // Sensor CLI
sensorCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'R': // Reset to Bootloader
cliPortPrint("Entering Bootloader....\n\n");
delay(100);
systemReset(true);
break;
///////////////////////////////
case 'S': // Reset System
cliPortPrint("\nSystem Reseting....\n\n");
delay(100);
systemReset(false);
break;
///////////////////////////////
case 'T': // Telemetry CLI
telemetryCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'U': // EEPROM CLI
eepromCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'V': // Reset EEPROM Parameters
cliPortPrint( "\nEEPROM Parameters Reset....\n" );
checkFirstTime(true);
cliPortPrint("\nSystem Resetting....\n\n");
delay(100);
systemReset(false);
break;
///////////////////////////////
case 'W': // Write EEPROM Parameters
cliPortPrint("\nWriting EEPROM Parameters....\n");
writeEEPROM();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'X': // Not Used
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'Y': // Not Used
cliQuery = 'x';
break;
///////////////////////////////
case 'Z': // Not Used
cliQuery = 'x';
break;
///////////////////////////////
case '?': // Command Summary
cliBusy = true;
cliPortPrint("\n");
cliPortPrint("'a' Rate PIDs 'A' Set Roll Rate PID Data AB;P;I;D;windupGuard;dErrorCalc\n");
cliPortPrint("'b' Attitude PIDs 'B' Set Pitch Rate PID Data BB;P;I;D;windupGuard;dErrorCalc\n");
cliPortPrint("'c' Velocity PIDs 'C' Set Yaw Rate PID Data CB;P;I;D;windupGuard;dErrorCalc\n");
cliPortPrint("'d' Position PIDs 'D' Set Roll Att PID Data DB;P;I;D;windupGuard;dErrorCalc\n");
cliPortPrint("'e' Loop Delta Times 'E' Set Pitch Att PID Data EB;P;I;D;windupGuard;dErrorCalc\n");
cliPortPrint("'f' Loop Execution Times 'F' Set Hdg Hold PID Data FB;P;I;D;windupGuard;dErrorCalc\n");
cliPortPrint("'g' 500 Hz Accels 'G' Not Used\n");
cliPortPrint("'h' 100 Hz Earth Axis Accels 'H' Not Used\n");
cliPortPrint("'i' 500 Hz Gyros 'I' Set hDot PID Data IB;P;I;D;windupGuard;dErrorCalc\n");
cliPortPrint("'j' 10 hz Mag Data 'J' Not Used\n");
cliPortPrint("'k' Vertical Axis Variable 'K' Not Used\n");
cliPortPrint("'l' Attitudes 'L' Set h PID Data LB;P;I;D;windupGuard;dErrorCalc\n");
cliPortPrint("\n");
cliPortPrint("Press space bar for more, or enter a command....\n");
while (cliPortAvailable() == false);
cliQuery = cliPortRead();
if (cliQuery != ' ')
{
validCliCommand = true;
cliBusy = false;
return;
}
cliPortPrint("\n");
cliPortPrint("'m' Axis PIDs 'M' Not Used\n");
cliPortPrint("'n' Not Used 'N' Mixer CLI\n");
cliPortPrint("'o' Battery Voltage 'O' Receiver CLI\n");
cliPortPrint("'p' Not Used 'P' Sensor CLI\n");
cliPortPrint("'q' Primary Spektrum Raw Data 'Q' Not Used\n");
cliPortPrint("'r' Mode States 'R' Reset and Enter Bootloader\n");
cliPortPrint("'s' Raw Receiver Commands 'S' Reset\n");
cliPortPrint("'t' Processed Receiver Commands 'T' Telemetry CLI\n");
cliPortPrint("'u' Command In Detent Discretes 'U' EEPROM CLI\n");
cliPortPrint("'v' Motor PWM Outputs 'V' Reset EEPROM Parameters\n");
cliPortPrint("'w' Not Used 'W' Write EEPROM Parameters\n");
cliPortPrint("'x' Terminate Serial Communication 'X' Not Used\n");
cliPortPrint("\n");
cliPortPrint("Press space bar for more, or enter a command....\n");
while (cliPortAvailable() == false);
cliQuery = cliPortRead();
if (cliQuery != ' ')
{
validCliCommand = true;
cliBusy = false;
return;
}
cliPortPrint("\n");
cliPortPrint("'y' ESC Calibration 'Y' Not Used\n");
cliPortPrint("'z' ADC Values 'Z' Not Used\n");
cliPortPrint("'#####' Toggle MavLink Msg State '?' Command Summary\n");
cliPortPrint("\n");
cliQuery = 'x';
cliBusy = false;
break;
///////////////////////////////
}
}
}
void cliCom(void)
{
uint8_t index;
uint8_t numChannels = 8;
char mvlkToggleString[5] = { 0, 0, 0, 0, 0 };
if (eepromConfig.receiverType == PPM)
numChannels = eepromConfig.ppmChannels;
if ((cliPortAvailable() && !validCliCommand))
{
cliQuery = cliPortRead();
if (cliQuery == '#') // Check to see if we should toggle mavlink msg state
{
while (cliPortAvailable == false);
readStringCLI(mvlkToggleString, 5);
if ((mvlkToggleString[0] == '#') &&
(mvlkToggleString[1] == '#') &&
(mvlkToggleString[2] == '#') &&
(mvlkToggleString[3] == '#'))
{
if (eepromConfig.mavlinkEnabled == false)
{
eepromConfig.mavlinkEnabled = true;
eepromConfig.activeTelemetry = 0x0000;
}
else
{
eepromConfig.mavlinkEnabled = false;
}
if (mvlkToggleString[4] == 'W')
{
cliPortPrint("\nWriting EEPROM Parameters....\n");
writeEEPROM();
}
}
}
}
validCliCommand = false;
if ((eepromConfig.mavlinkEnabled == false) && (cliQuery != '#'))
{
switch (cliQuery)
{
///////////////////////////////
case 'a': // Rate PIDs
cliPortPrintF("\nRoll Rate PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[ROLL_RATE_PID].P,
eepromConfig.PID[ROLL_RATE_PID].I,
eepromConfig.PID[ROLL_RATE_PID].D,
eepromConfig.PID[ROLL_RATE_PID].Limit);
cliPortPrintF( "Pitch Rate PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[PITCH_RATE_PID].P,
eepromConfig.PID[PITCH_RATE_PID].I,
eepromConfig.PID[PITCH_RATE_PID].D,
eepromConfig.PID[PITCH_RATE_PID].Limit);
cliPortPrintF( "Yaw Rate PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[YAW_RATE_PID].P,
eepromConfig.PID[YAW_RATE_PID].I,
eepromConfig.PID[YAW_RATE_PID].D,
eepromConfig.PID[YAW_RATE_PID].Limit);
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'b': // Attitude PIDs
cliPortPrintF("\nRoll Attitude PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[ROLL_ATT_PID].P,
eepromConfig.PID[ROLL_ATT_PID].I,
eepromConfig.PID[ROLL_ATT_PID].D,
eepromConfig.PID[ROLL_ATT_PID].Limit);
cliPortPrintF( "Pitch Attitude PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[PITCH_ATT_PID].P,
eepromConfig.PID[PITCH_ATT_PID].I,
eepromConfig.PID[PITCH_ATT_PID].D,
eepromConfig.PID[PITCH_ATT_PID].Limit);
cliPortPrintF( "Heading PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[HEADING_PID].P,
eepromConfig.PID[HEADING_PID].I,
eepromConfig.PID[HEADING_PID].D,
eepromConfig.PID[HEADING_PID].Limit);
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'c': // Velocity PIDs
cliPortPrintF("\nnDot PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[NDOT_PID].P,
eepromConfig.PID[NDOT_PID].I,
eepromConfig.PID[NDOT_PID].D,
eepromConfig.PID[NDOT_PID].Limit);
cliPortPrintF( "eDot PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[EDOT_PID].P,
eepromConfig.PID[EDOT_PID].I,
eepromConfig.PID[EDOT_PID].D,
eepromConfig.PID[EDOT_PID].Limit);
cliPortPrintF( "hDot PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[HDOT_PID].P,
eepromConfig.PID[HDOT_PID].I,
eepromConfig.PID[HDOT_PID].D,
eepromConfig.PID[HDOT_PID].Limit);
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'd': // Position PIDs
cliPortPrintF("\nN PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[N_PID].P,
eepromConfig.PID[N_PID].I,
eepromConfig.PID[N_PID].D,
eepromConfig.PID[N_PID].Limit);
cliPortPrintF( "E PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[E_PID].P,
eepromConfig.PID[E_PID].I,
eepromConfig.PID[E_PID].D,
eepromConfig.PID[E_PID].Limit);
cliPortPrintF( "h PID: %8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[H_PID].P,
eepromConfig.PID[H_PID].I,
eepromConfig.PID[H_PID].D,
eepromConfig.PID[H_PID].Limit);
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'e': // Loop Delta Times
cliPortPrintF("%7ld, %7ld, %7ld, %7ld, %7ld, %7ld, %7ld\n", deltaTime1000Hz,
deltaTime500Hz,
deltaTime100Hz,
deltaTime50Hz,
deltaTime10Hz,
deltaTime5Hz,
deltaTime1Hz);
validCliCommand = false;
break;
///////////////////////////////
case 'f': // Loop Execution Times
cliPortPrintF("%7ld, %7ld, %7ld, %7ld, %7ld, %7ld, %7ld\n", executionTime1000Hz,
executionTime500Hz,
executionTime100Hz,
executionTime50Hz,
executionTime10Hz,
executionTime5Hz,
executionTime1Hz);
validCliCommand = false;
break;
///////////////////////////////
case 'g': // 100 Hz Accels
cliPortPrintF("%9.4f, %9.4f, %9.4f\n", sensors.accel100Hz[XAXIS],
sensors.accel100Hz[YAXIS],
sensors.accel100Hz[ZAXIS]);
validCliCommand = false;
break;
///////////////////////////////
case 'h': // 100 hz Earth Axis Accels
cliPortPrintF("%9.4f, %9.4f, %9.4f\n", earthAxisAccels[XAXIS],
earthAxisAccels[YAXIS],
earthAxisAccels[ZAXIS]);
validCliCommand = false;
break;
///////////////////////////////
case 'i': // 500 hz Gyros
cliPortPrintF("%9.4f, %9.4f, %9.4f, %9.4f\n", sensors.gyro500Hz[ROLL ] * R2D,
sensors.gyro500Hz[PITCH] * R2D,
sensors.gyro500Hz[YAW ] * R2D,
mpu6000Temperature);
validCliCommand = false;
break;
///////////////////////////////
case 'j': // 10 Hz Mag Data
cliPortPrintF("%9.4f, %9.4f, %9.4f\n", sensors.mag10Hz[XAXIS],
sensors.mag10Hz[YAXIS],
sensors.mag10Hz[ZAXIS]);
validCliCommand = false;
break;
///////////////////////////////
case 'k': // Vertical Axis Variables
cliPortPrintF("%9.4f, %9.4f, %9.4f, %9.4f, %4ld, %9.4f\n", earthAxisAccels[ZAXIS],
sensors.pressureAlt50Hz,
hDotEstimate,
hEstimate,
ms5611Temperature,
aglRead());
validCliCommand = false;
break;
///////////////////////////////
case 'l': // Attitudes
cliPortPrintF("%9.4f, %9.4f, %9.4f\n", sensors.attitude500Hz[ROLL ] * R2D,
sensors.attitude500Hz[PITCH] * R2D,
sensors.attitude500Hz[YAW ] * R2D);
validCliCommand = false;
break;
///////////////////////////////
case 'm': // Axis PIDs
cliPortPrintF("%9.4f, %9.4f, %9.4f\n", ratePID[ROLL ],
ratePID[PITCH],
ratePID[YAW ]);
validCliCommand = false;
break;
///////////////////////////////
case 'n': // GPS Data
switch (gpsDataType)
{
///////////////////////
case 0:
cliPortPrintF("%12ld, %12ld, %12ld, %12ld, %12ld, %12ld, %4d, %4d\n", gps.latitude,
gps.longitude,
gps.hMSL,
gps.velN,
gps.velE,
gps.velD,
gps.fix,
gps.numSats);
break;
///////////////////////
case 1:
cliPortPrintF("%3d: ", gps.numCh);
for (index = 0; index < gps.numCh; index++)
cliPortPrintF("%3d ", gps.chn[index]);
cliPortPrint("\n");
break;
///////////////////////
case 2:
cliPortPrintF("%3d: ", gps.numCh);
for (index = 0; index < gps.numCh; index++)
cliPortPrintF("%3d ", gps.svid[index]);
cliPortPrint("\n");
break;
///////////////////////
case 3:
cliPortPrintF("%3d: ", gps.numCh);
for (index = 0; index < gps.numCh; index++)
cliPortPrintF("%3d ", gps.cno[index]);
cliPortPrint("\n");
break;
///////////////////////
}
validCliCommand = false;
break;
///////////////////////////////
case 'o':
cliPortPrintF("%9.4f\n", batteryVoltage);
validCliCommand = false;
break;
///////////////////////////////
case 'p': // Using for Nav Debug
// cliPortPrintF("CurrentLLA:%d,%d, CurrentWP:%d,%d, NextWP:%d,%d\n",
// currentPosition.latitude,
// currentPosition.longitude,
// fromWaypoint.latitude,
// fromWaypoint.longitude,
// toWaypoint.latitude,
// toWaypoint.longitude);
cliPortPrintF("xt:%.9f, xte:%.9f, tae: %.9f, dist:%.3f\n",
crossTrack, crossTrackError, trackAngleError, distanceToNextWaypoint);
//cliQuery = 'x';
//validCliCommand = false;
break;
///////////////////////////////
case 'q': // Using for Nav Debug
cliPortPrintF("State:%d, WP:%d, P:%.1f, R:%.1f, Y:%.1f, Curr:%.1f, Des:%.1f, Dist:%.8f\n",
nextNavState,
waypointIndex,
ratePID[PITCH],
ratePID[ROLL],
ratePID[YAW],
currentHeading,
desiredHeading,
distanceToNextWaypoint);
//cliQuery = 'x';
//validCliCommand = false;
break;
///////////////////////////////
case 'r':
if (flightMode == RATE)
cliPortPrint("Flight Mode:RATE ");
else if (flightMode == ATTITUDE)
cliPortPrint("Flight Mode:ATTITUDE ");
else if (flightMode == GPS)
cliPortPrint("Flight Mode:GPS ");
if (headingHoldEngaged == true)
cliPortPrint("Heading Hold:ENGAGED ");
else
cliPortPrint("Heading Hold:DISENGAGED ");
switch (verticalModeState)
{
case ALT_DISENGAGED_THROTTLE_ACTIVE:
cliPortPrint("Alt:Disenaged Throttle Active ");
break;
case ALT_HOLD_FIXED_AT_ENGAGEMENT_ALT:
cliPortPrint("Alt:Hold Fixed at Engagement Alt ");
break;
case ALT_HOLD_AT_REFERENCE_ALTITUDE:
cliPortPrint("Alt:Hold at Reference Alt ");
break;
case VERTICAL_VELOCITY_HOLD_AT_REFERENCE_VELOCITY:
cliPortPrint("Alt:Velocity Hold at Reference Vel ");
break;
case ALT_DISENGAGED_THROTTLE_INACTIVE:
cliPortPrint("Alt:Disengaged Throttle Inactive ");
break;
}
if (rxCommand[AUX3] > MIDCOMMAND)
cliPortPrint("Mode:Simple ");
else
cliPortPrint("Mode:Normal ");
if (rxCommand[AUX4] > MIDCOMMAND)
cliPortPrint("Emergency Bail:Active\n");
else
cliPortPrint("Emergency Bail:Inactive\n");
validCliCommand = false;
break;
///////////////////////////////
case 's': // Raw Receiver Commands
if ((eepromConfig.receiverType == SPEKTRUM) && (maxChannelNum > 0))
{
for (index = 0; index < maxChannelNum - 1; index++)
cliPortPrintF("%4ld, ", spektrumBuf[index]);
cliPortPrintF("%4ld\n", spektrumBuf[maxChannelNum - 1]);
}
else if (eepromConfig.receiverType == SBUS)
{
for (index = 0; index < 7; index++)
cliPortPrintF("%4ld, ", sBusRead(index));
cliPortPrintF("%4ld\n", sBusRead(7));
}
else
{
for (index = 0; index < numChannels - 1; index++)
cliPortPrintF("%4i, ", Inputs[index].pulseWidth);
cliPortPrintF("%4i\n", Inputs[numChannels - 1].pulseWidth);
}
validCliCommand = false;
break;
///////////////////////////////
case 't': // Processed Receiver Commands
for (index = 0; index < numChannels - 1; index++)
cliPortPrintF("%8.2f, ", rxCommand[index]);
cliPortPrintF("%8.2f\n", rxCommand[numChannels - 1]);
validCliCommand = false;
break;
///////////////////////////////
case 'u': // Command in Detent Discretes
cliPortPrintF("%s, ", commandInDetent[ROLL ] ? " true" : "false");
cliPortPrintF("%s, ", commandInDetent[PITCH] ? " true" : "false");
cliPortPrintF("%s\n", commandInDetent[YAW ] ? " true" : "false");
validCliCommand = false;
break;
///////////////////////////////
case 'v': // ESC PWM Outputs
cliPortPrintF("%4ld, ", TIM8->CCR4);
cliPortPrintF("%4ld, ", TIM8->CCR3);
cliPortPrintF("%4ld, ", TIM8->CCR2);
cliPortPrintF("%4ld, ", TIM8->CCR1);
cliPortPrintF("%4ld, ", TIM2->CCR1);
cliPortPrintF("%4ld, ", TIM2->CCR2);
cliPortPrintF("%4ld, ", TIM3->CCR1);
cliPortPrintF("%4ld\n", TIM3->CCR2);
validCliCommand = false;
break;
///////////////////////////////
case 'w': // Servo PWM Outputs
cliPortPrintF("%4ld, ", TIM5->CCR3);
cliPortPrintF("%4ld, ", TIM5->CCR2);
cliPortPrintF("%4ld\n", TIM5->CCR1);
validCliCommand = false;
break;
///////////////////////////////
case 'x':
validCliCommand = false;
break;
///////////////////////////////
case 'y': // ESC Calibration
escCalibration();
cliQuery = 'x';
break;
///////////////////////////////
case 'z': // ADC readings
cliPortPrintF("%8.4f, %8.4f, %8.4f, %8.4f, %8.4f, %8.4f, %8.4f\n", adcValue(1),
adcValue(2),
adcValue(3),
adcValue(4),
adcValue(5),
adcValue(6),
adcValue(7));
break;
///////////////////////////////
///////////////////////////////////////////////////////////////////////
///////////////////////////////////////////////////////////////////////
///////////////////////////////////////////////////////////////////////
///////////////////////////////////////////////////////////////////////
///////////////////////////////
case 'A': // Read Roll Rate PID Values
readCliPID(ROLL_RATE_PID);
cliPortPrint( "\nRoll Rate PID Received....\n" );
cliQuery = 'a';
validCliCommand = false;
break;
///////////////////////////////
case 'B': // Read Pitch Rate PID Values
readCliPID(PITCH_RATE_PID);
cliPortPrint( "\nPitch Rate PID Received....\n" );
cliQuery = 'a';
validCliCommand = false;
break;
///////////////////////////////
case 'C': // Read Yaw Rate PID Values
readCliPID(YAW_RATE_PID);
cliPortPrint( "\nYaw Rate PID Received....\n" );
cliQuery = 'a';
validCliCommand = false;
break;
///////////////////////////////
case 'D': // Read Roll Attitude PID Values
readCliPID(ROLL_ATT_PID);
cliPortPrint( "\nRoll Attitude PID Received....\n" );
cliQuery = 'b';
validCliCommand = false;
break;
///////////////////////////////
case 'E': // Read Pitch Attitude PID Values
readCliPID(PITCH_ATT_PID);
cliPortPrint( "\nPitch Attitude PID Received....\n" );
cliQuery = 'b';
validCliCommand = false;
break;
///////////////////////////////
case 'F': // Read Heading Hold PID Values
readCliPID(HEADING_PID);
cliPortPrint( "\nHeading PID Received....\n" );
cliQuery = 'b';
validCliCommand = false;
break;
///////////////////////////////
case 'G': // Read nDot PID Values
readCliPID(NDOT_PID);
cliPortPrint( "\nnDot PID Received....\n" );
cliQuery = 'c';
validCliCommand = false;
break;
///////////////////////////////
case 'H': // Read eDot PID Values
readCliPID(EDOT_PID);
cliPortPrint( "\neDot PID Received....\n" );
cliQuery = 'c';
validCliCommand = false;
break;
///////////////////////////////
case 'I': // Read hDot PID Values
readCliPID(HDOT_PID);
cliPortPrint( "\nhDot PID Received....\n" );
cliQuery = 'c';
validCliCommand = false;
break;
///////////////////////////////
case 'J': // Read n PID Values
readCliPID(N_PID);
cliPortPrint( "\nn PID Received....\n" );
cliQuery = 'd';
validCliCommand = false;
break;
///////////////////////////////
case 'K': // Read e PID Values
readCliPID(E_PID);
cliPortPrint( "\ne PID Received....\n" );
cliQuery = 'd';
validCliCommand = false;
break;
///////////////////////////////
case 'L': // Read h PID Values
readCliPID(H_PID);
cliPortPrint( "\nh PID Received....\n" );
cliQuery = 'd';
validCliCommand = false;
break;
///////////////////////////////
case 'M': // MAX7456 CLI
max7456CLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'N': // Mixer CLI
mixerCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'O': // Receiver CLI
receiverCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'P': // Sensor CLI
sensorCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'Q': // GPS Data Selection
gpsDataType = (uint8_t)readFloatCLI();
cliPortPrint("\n");
cliQuery = 'n';
validCliCommand = false;
break;
///////////////////////////////
case 'R': // Reset to Bootloader
cliPortPrint("Entering Bootloader....\n\n");
delay(100);
systemReset(true);
break;
///////////////////////////////
case 'S': // Reset System
cliPortPrint("\nSystem Reseting....\n\n");
delay(100);
systemReset(false);
break;
///////////////////////////////
case 'T': // Telemetry CLI
telemetryCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'U': // EEPROM CLI
eepromCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'V': // Reset EEPROM Parameters
cliPortPrint( "\nEEPROM Parameters Reset....\n" );
checkFirstTime(true);
cliPortPrint("\nSystem Resetting....\n\n");
delay(100);
systemReset(false);
break;
///////////////////////////////
case 'W': // Write EEPROM Parameters
cliPortPrint("\nWriting EEPROM Parameters....\n");
writeEEPROM();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'X': // Not Used
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'Y': // ADC CLI
adcCLI();
cliQuery = 'x';
validCliCommand = false;
break;
///////////////////////////////
case 'Z': // Not Used
computeGeoMagElements();
cliQuery = 'x';
break;
///////////////////////////////
//////////////////////////////////////////////////////////////////////////////////
// Communicator Messages /////////////////////////////////////////////////////
//////////////////////////////////////////////////////////////////////////////////
///////////////////////////////
case '@': // Communicator Messages
{
uint8_t msgType = cliPortRead();
switch (msgType) //update this
{
case 's': // Write out vehicle status
if (statusType++ < 3)
{
cliPortPrint("0");
cliPortPrintF("%1d", armed);
cliPortPrintF("%1d", flightMode);
cliPortPrintF("%1d", autoNavMode);
cliPortPrintF("%1d", verticalModeState);
cliPortPrintF("%1d", execUp);
writeShort(batteryVoltage * 100);
writeShort(hEstimate * 100);
writeShort(sensors.attitude500Hz[ROLL] * R2D * 10);
writeShort(sensors.attitude500Hz[PITCH] * R2D * 10);
writeShort(sensors.attitude500Hz[YAW] * R2D * 10);
writeShort(rxCommand[0]);
writeShort(rxCommand[1]);
writeShort(rxCommand[2]);
writeShort(rxCommand[3]);
cliPortPrint("\n"); // 25 bytes
}
else
{
cliPortPrint("1");
writeShort(rxCommand[4]);
writeShort(rxCommand[5]);
writeShort(rxCommand[6]);
writeShort(rxCommand[7]);
writeShort(TIM8->CCR4);
writeShort(TIM8->CCR3);
writeShort(TIM8->CCR2);
writeShort(TIM8->CCR1);
writeShort(TIM2->CCR1);
writeShort(TIM2->CCR2);
writeShort(TIM3->CCR1);
writeShort(TIM3->CCR2);
cliPortPrint("\n"); // 26 bytes
statusType = 0;
}
break;
case 'O': // Read in waypoints
{
int index = readFloatCLI();
if (index >= 0)
{
eepromConfig.route[index].latitude = readFloatCLI();
eepromConfig.route[index].longitude = readFloatCLI();
eepromConfig.route[index].altitude = readFloatCLI();
eepromConfig.route[index].speed = 1;
eepromConfig.route[index].type = 0;
}
else if (index == -1)
eepromConfig.storedWaypointCount = readFloatCLI();
break;
}
case 'o': // Write out waypoints
{
int index = readFloatCLI();
if (index < 0)
cliPortPrintF("%d\n", eepromConfig.storedWaypointCount);
else
{
cliPortPrintF("%d,%d,%d,%d\n",
index,
eepromConfig.route[index].latitude,
eepromConfig.route[index].longitude,
eepromConfig.route[index].altitude,
eepromConfig.route[index].speed,
eepromConfig.route[index].type);
}
}
break;
case '^': // Write out AutoNav status
{
int type = readFloatCLI();
if (type == 0) // send shortened position data
{
cliPortPrintF("%d,%d,%.1f\n",
gps.latitude,
gps.longitude,
sensors.attitude500Hz[YAW]*R2D);
}
if (type == 1)
{
cliPortPrintF("%d,%d,%d\n",
gps.hMSL,
gps.heading,
gps.speed);
}
if (type == 2)
{
cliPortPrintF("%d,%d,%d\n",
gps.numSats,
gps.hDop,
gps.fix);
}
if (type == 3) // send stored home position
{
cliPortPrintF("%d,%d,%d\n",
homePosition.latitude,
homePosition.longitude,
homePosition.altitude);
}
break;
}
case '!': // send software version
cliPortPrintF("%s\n", __AQ32PLUS_VERSION);
break;
case '<': // send autoNav status
cliPortPrintF("%d\n", getAutoNavState());
break;
case '>': // setup autopilot states
setAutoNavState(readFloatCLI());
break;
case 'M': // Read in mode setup
{
int slot = readFloatCLI();
eepromConfig.mode[slot].modeType = readFloatCLI();
eepromConfig.mode[slot].channel = readFloatCLI();
eepromConfig.mode[slot].state = readFloatCLI();
eepromConfig.mode[slot].minChannelValue = readFloatCLI();
eepromConfig.mode[slot].maxChannelValue = readFloatCLI();
break;
}
case 'm': // Write out mode setup
{
int slot = readFloatCLI();
cliPortPrintF("%d,%d,%d,%d,%d,%d\n",
slot,
eepromConfig.mode[slot].modeType,
eepromConfig.mode[slot].channel,
eepromConfig.mode[slot].state,
eepromConfig.mode[slot].minChannelValue,
eepromConfig.mode[slot].maxChannelValue);
break;
}
case 'A': // Read in AutoNav PIDs
{
int pidType = readFloatCLI();
readCliPID(pidType);
break;
}
case 'a': // Write out AutoNav PIDs
cliPortPrintF("%8.4f, %8.4f, %8.4f, %8.4f,", eepromConfig.PID[AUTONAV_ROLL_PID].P,
eepromConfig.PID[AUTONAV_ROLL_PID].I,
eepromConfig.PID[AUTONAV_ROLL_PID].D,
eepromConfig.PID[AUTONAV_ROLL_PID].Limit);
cliPortPrintF("%8.4f, %8.4f, %8.4f, %8.4f,", eepromConfig.PID[AUTONAV_PITCH_PID].P,
eepromConfig.PID[AUTONAV_PITCH_PID].I,
eepromConfig.PID[AUTONAV_PITCH_PID].D,
eepromConfig.PID[AUTONAV_PITCH_PID].Limit);
cliPortPrintF("%8.4f, %8.4f, %8.4f, %8.4f\n", eepromConfig.PID[AUTONAV_YAW_PID].P,
eepromConfig.PID[AUTONAV_YAW_PID].I,
eepromConfig.PID[AUTONAV_YAW_PID].D,
eepromConfig.PID[AUTONAV_YAW_PID].Limit);
break;
case 'C':
eepromConfig.xteScaling = readFloatCLI();
break;
case 'c':
cliPortPrintF("%.3f\n", eepromConfig.xteScaling);
break;
}
cliQuery = 'x';
validCliCommand = false;
break;
}
///////////////////////////////
//////////////////////////////////////////////////////////////////////////////////
//////////////////////////////////////////////////////////////////////////////////
//////////////////////////////////////////////////////////////////////////////////
///////////////////////////////
case '?': // Command Summary
cliBusy = true;
cliPortPrint("\n");
cliPortPrint("'a' Rate PIDs 'A' Set Roll Rate PID Data AP;I;D;N\n");
cliPortPrint("'b' Attitude PIDs 'B' Set Pitch Rate PID Data BP;I;D;N\n");
cliPortPrint("'c' Velocity PIDs 'C' Set Yaw Rate PID Data CP;I;D;N\n");
cliPortPrint("'d' Position PIDs 'D' Set Roll Att PID Data DP;I;D;N\n");
cliPortPrint("'e' Loop Delta Times 'E' Set Pitch Att PID Data EP;I;D;N\n");
cliPortPrint("'f' Loop Execution Times 'F' Set Hdg Hold PID Data FP;I;D;N\n");
cliPortPrint("'g' 500 Hz Accels 'G' Set nDot PID Data GP;I;D;N\n");
cliPortPrint("'h' 100 Hz Earth Axis Accels 'H' Set eDot PID Data HP;I;D;N\n");
cliPortPrint("'i' 500 Hz Gyros 'I' Set hDot PID Data IP;I;D;N\n");
cliPortPrint("'j' 10 hz Mag Data 'J' Set n PID Data JP;I;D;N\n");
cliPortPrint("'k' Vertical Axis Variable 'K' Set e PID Data KP;I;D;N\n");
cliPortPrint("'l' Attitudes 'L' Set h PID Data LP;I;D;N\n");
cliPortPrint("\n");
cliPortPrint("Press space bar for more, or enter a command....\n");
while (cliPortAvailable() == false);
cliQuery = cliPortRead();
if (cliQuery != ' ')
{
validCliCommand = true;
cliBusy = false;
return;
}
cliPortPrint("\n");
cliPortPrint("'m' Axis PIDs 'M' MAX7456 CLI\n");
cliPortPrint("'n' GPS Data 'N' Mixer CLI\n");
cliPortPrint("'o' Battery Voltage 'O' Receiver CLI\n");
cliPortPrint("'p' Not Used 'P' Sensor CLI\n");
cliPortPrint("'q' Not Used 'Q' GPS Data Selection\n");
cliPortPrint("'r' Mode States 'R' Reset and Enter Bootloader\n");
cliPortPrint("'s' Raw Receiver Commands 'S' Reset\n");
cliPortPrint("'t' Processed Receiver Commands 'T' Telemetry CLI\n");
cliPortPrint("'u' Command In Detent Discretes 'U' EEPROM CLI\n");
cliPortPrint("'v' Motor PWM Outputs 'V' Reset EEPROM Parameters\n");
cliPortPrint("'w' Servo PWM Outputs 'W' Write EEPROM Parameters\n");
cliPortPrint("'x' Terminate Serial Communication 'X' Not Used\n");
cliPortPrint("\n");
cliPortPrint("Press space bar for more, or enter a command....\n");
while (cliPortAvailable() == false);
cliQuery = cliPortRead();
if (cliQuery != ' ')
{
validCliCommand = true;
cliBusy = false;
return;
}
cliPortPrint("\n");
cliPortPrint("'y' ESC Calibration/Motor Verification 'Y' ADC CLI\n");
cliPortPrint("'z' ADC Values 'Z' WMM Test\n");
cliPortPrint(" '?' Command Summary\n");
cliPortPrint("\n");
cliQuery = 'x';
cliBusy = false;
break;
///////////////////////////////
}
}
}