/**
* handle_edge_irq - edge type IRQ handler
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Interrupt occures on the falling and/or rising edge of a hardware
* signal. The occurence is latched into the irq controller hardware
* and must be acked in order to be reenabled. After the ack another
* interrupt can happen on the same source even before the first one
* is handled by the associated event handler. If this happens it
* might be necessary to disable (mask) the interrupt depending on the
* controller hardware. This requires to reenable the interrupt inside
* of the loop which handles the interrupts which have arrived while
* the handler was running. If all pending interrupts are handled, the
* loop is left.
*/
void
handle_edge_irq(unsigned int irq, struct irq_desc *desc)
{
raw_spin_lock(&desc->lock);
desc->status &= ~(IRQ_REPLAY | IRQ_WAITING);
/*
* If we're currently running this IRQ, or its disabled,
* we shouldn't process the IRQ. Mark it pending, handle
* the necessary masking and go out
*/
if (unlikely((desc->status & (IRQ_INPROGRESS | IRQ_DISABLED)) ||
!desc->action)) {
desc->status |= (IRQ_PENDING | IRQ_MASKED);
mask_ack_irq(desc, irq);
goto out_unlock;
}
kstat_incr_irqs_this_cpu(irq, desc);
/* Start handling the irq */
if (desc->chip->ack)
desc->chip->ack(irq);
/* Mark the IRQ currently in progress.*/
desc->status |= IRQ_INPROGRESS;
do {
struct irqaction *action = desc->action;
irqreturn_t action_ret;
if (unlikely(!action)) {
mask_irq(desc, irq);
goto out_unlock;
}
/*
* When another irq arrived while we were handling
* one, we could have masked the irq.
* Renable it, if it was not disabled in meantime.
*/
if (unlikely((desc->status &
(IRQ_PENDING | IRQ_MASKED | IRQ_DISABLED)) ==
(IRQ_PENDING | IRQ_MASKED))) {
unmask_irq(desc, irq);
}
desc->status &= ~IRQ_PENDING;
raw_spin_unlock(&desc->lock);
action_ret = handle_IRQ_event(irq, action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
raw_spin_lock(&desc->lock);
} while ((desc->status & (IRQ_PENDING | IRQ_DISABLED)) == IRQ_PENDING);
desc->status &= ~IRQ_INPROGRESS;
out_unlock:
raw_spin_unlock(&desc->lock);
}
/**
* handle_simple_irq - Simple and software-decoded IRQs.
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Simple interrupts are either sent from a demultiplexing interrupt
* handler or come from hardware, where no interrupt hardware control
* is necessary.
*
* Note: The caller is expected to handle the ack, clear, mask and
* unmask issues if necessary.
*/
void fastcall
handle_simple_irq(unsigned int irq, struct irq_desc *desc)
{
struct irqaction *action;
irqreturn_t action_ret;
const unsigned int cpu = smp_processor_id();
spin_lock(&desc->lock);
if (unlikely(desc->status & IRQ_INPROGRESS))
goto out_unlock;
kstat_cpu(cpu).irqs[irq]++;
action = desc->action;
if (unlikely(!action || (desc->status & IRQ_DISABLED))) {
if (desc->chip->mask)
desc->chip->mask(irq);
desc->status &= ~(IRQ_REPLAY | IRQ_WAITING);
desc->status |= IRQ_PENDING;
goto out_unlock;
}
desc->status &= ~(IRQ_REPLAY | IRQ_WAITING | IRQ_PENDING);
desc->status |= IRQ_INPROGRESS;
spin_unlock(&desc->lock);
action_ret = handle_IRQ_event(irq, action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
spin_lock(&desc->lock);
desc->status &= ~IRQ_INPROGRESS;
out_unlock:
spin_unlock(&desc->lock);
}
/*
* handle_nested_irq - Handle a nested irq from a irq thread
* @irq: the interrupt number
*
* Handle interrupts which are nested into a threaded interrupt
* handler. The handler function is called inside the calling
* threads context.
*/
void handle_nested_irq(unsigned int irq)
{
struct irq_desc *desc = irq_to_desc(irq);
struct irqaction *action;
irqreturn_t action_ret;
might_sleep();
raw_spin_lock_irq(&desc->lock);
kstat_incr_irqs_this_cpu(irq, desc);
action = desc->action;
if (unlikely(!action || (desc->istate & IRQS_DISABLED)))
goto out_unlock;
irq_compat_set_progress(desc);
desc->istate |= IRQS_INPROGRESS;
raw_spin_unlock_irq(&desc->lock);
action_ret = action->thread_fn(action->irq, action->dev_id);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
raw_spin_lock_irq(&desc->lock);
desc->istate &= ~IRQS_INPROGRESS;
irq_compat_clr_progress(desc);
out_unlock:
raw_spin_unlock_irq(&desc->lock);
}
/**
* handle_simple_irq - Simple and software-decoded IRQs.
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Simple interrupts are either sent from a demultiplexing interrupt
* handler or come from hardware, where no interrupt hardware control
* is necessary.
*
* Note: The caller is expected to handle the ack, clear, mask and
* unmask issues if necessary.
*/
void
handle_simple_irq(unsigned int irq, struct irq_desc *desc)
{
struct irqaction *action;
irqreturn_t action_ret;
raw_spin_lock(&desc->lock);
if (unlikely(desc->status & IRQ_INPROGRESS))
goto out_unlock;
desc->status &= ~(IRQ_REPLAY | IRQ_WAITING);
kstat_incr_irqs_this_cpu(irq, desc);
action = desc->action;
if (unlikely(!action || (desc->status & IRQ_DISABLED)))
goto out_unlock;
desc->status |= IRQ_INPROGRESS;
raw_spin_unlock(&desc->lock);
action_ret = handle_IRQ_event(irq, action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
raw_spin_lock(&desc->lock);
desc->status &= ~IRQ_INPROGRESS;
out_unlock:
raw_spin_unlock(&desc->lock);
}
/*
* handle_nested_irq - Handle a nested irq from a irq thread
* @irq: the interrupt number
*
* Handle interrupts which are nested into a threaded interrupt
* handler. The handler function is called inside the calling
* threads context.
*/
void handle_nested_irq(unsigned int irq)
{
struct irq_desc *desc = irq_to_desc(irq);
struct irqaction *action;
irqreturn_t action_ret;
might_sleep();
raw_spin_lock_irq(&desc->lock);
desc->istate &= ~(IRQS_REPLAY | IRQS_WAITING);
kstat_incr_irqs_this_cpu(irq, desc);
action = desc->action;
if (unlikely(!action || irqd_irq_disabled(&desc->irq_data))) {
desc->istate |= IRQS_PENDING;
goto out_unlock;
}
irqd_set(&desc->irq_data, IRQD_IRQ_INPROGRESS);
raw_spin_unlock_irq(&desc->lock);
action_ret = action->thread_fn(action->irq, action->dev_id);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
raw_spin_lock_irq(&desc->lock);
irqd_clear(&desc->irq_data, IRQD_IRQ_INPROGRESS);
out_unlock:
raw_spin_unlock_irq(&desc->lock);
}
irqreturn_t
handle_irq_event_percpu(struct irq_desc *desc, struct irqaction *action)
{
irqreturn_t retval = IRQ_NONE;
unsigned int random = 0, irq = desc->irq_data.irq;
do {
irqreturn_t res;
#ifdef CONFIG_SEC_DEBUG
sec_debug_timer_log(4444, (int)irqs_disabled(),
(void *)action->handler);
#endif
trace_irq_handler_entry(irq, action);
res = action->handler(irq, action->dev_id);
trace_irq_handler_exit(irq, action, res);
#ifdef CONFIG_SEC_DEBUG
sec_debug_timer_log(5555, (int)irqs_disabled(),
(void *)action->handler);
/* sec_debug_irq_sched_log(irq, (void *)action->handler, 2); */
#endif
if (WARN_ONCE(!irqs_disabled(),"irq %u handler %pF enabled interrupts\n",
irq, action->handler))
local_irq_disable();
switch (res) {
case IRQ_WAKE_THREAD:
/*
* Catch drivers which return WAKE_THREAD but
* did not set up a thread function
*/
if (unlikely(!action->thread_fn)) {
warn_no_thread(irq, action);
break;
}
irq_wake_thread(desc, action);
/* Fall through to add to randomness */
case IRQ_HANDLED:
random |= action->flags;
break;
default:
break;
}
retval |= res;
action = action->next;
} while (action);
if (random & IRQF_SAMPLE_RANDOM)
add_interrupt_randomness(irq);
if (!noirqdebug)
note_interrupt(irq, desc, retval);
return retval;
}
irqreturn_t
handle_irq_event_percpu(struct irq_desc *desc, struct irqaction *action)
{
irqreturn_t retval = IRQ_NONE;
unsigned int flags = 0, irq = desc->irq_data.irq;
#ifdef CONFIG_FOOTPRINT_IRQ
update_handle_irqs_this_cpu(irq);
#endif
do {
irqreturn_t res;
trace_irq_handler_entry(irq, action);
res = action->handler(irq, action->dev_id);
trace_irq_handler_exit(irq, action, res);
if (WARN_ONCE(!irqs_disabled(),"irq %u handler %pF enabled interrupts\n",
irq, action->handler))
local_irq_disable();
switch (res) {
case IRQ_WAKE_THREAD:
/*
* Catch drivers which return WAKE_THREAD but
* did not set up a thread function
*/
if (unlikely(!action->thread_fn)) {
warn_no_thread(irq, action);
break;
}
irq_wake_thread(desc, action);
/* Fall through to add to randomness */
case IRQ_HANDLED:
flags |= action->flags;
break;
default:
break;
}
retval |= res;
action = action->next;
} while (action);
add_interrupt_randomness(irq, flags);
if (!noirqdebug)
note_interrupt(irq, desc, retval);
#ifdef CONFIG_FOOTPRINT_IRQ
release_handle_irqs_this_cpu(irq);
#endif
return retval;
}
irqreturn_t
handle_irq_event_percpu(struct irq_desc *desc, struct irqaction *action)
{
irqreturn_t retval = IRQ_NONE;
unsigned int random = 0, irq = desc->irq_data.irq;
do {
irqreturn_t res;
trace_irq_handler_entry(irq, action);
res = action->handler(irq, action->dev_id);
trace_irq_handler_exit(irq, action, res);
if (WARN_ONCE(!irqs_disabled(),"irq %u handler %pF enabled interrupts\n",
irq, action->handler))
local_irq_disable();
switch (res) {
case IRQ_WAKE_THREAD:
/*
* Set result to handled so the spurious check
* does not trigger.
*/
res = IRQ_HANDLED;
/*
* Catch drivers which return WAKE_THREAD but
* did not set up a thread function
*/
if (unlikely(!action->thread_fn)) {
warn_no_thread(irq, action);
break;
}
irq_wake_thread(desc, action);
/* Fall through to add to randomness */
case IRQ_HANDLED:
random |= action->flags;
break;
default:
break;
}
retval |= res;
action = action->next;
} while (action);
if (random & IRQF_SAMPLE_RANDOM)
add_interrupt_randomness(irq);
if (!noirqdebug)
note_interrupt(irq, desc, retval);
return retval;
}
/**
* handle_level_irq - Level type irq handler
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Level type interrupts are active as long as the hardware line has
* the active level. This may require to mask the interrupt and unmask
* it after the associated handler has acknowledged the device, so the
* interrupt line is back to inactive.
*/
void
handle_level_irq(unsigned int irq, struct irq_desc *desc)
{
struct irqaction *action;
irqreturn_t action_ret;
spin_lock(&desc->lock);
/*
调用中断线所属的中断控制的mask_ack函数.
如果没有定义该函数，就调用mask，然后调用ack函数.
总之，对于水平触发的来说，它就是屏蔽当前的中断线，应当当前中断..
比如ARM来说，就是清除SRCPND、SRCINTPND寄存器的位.
*/
mask_ack_irq(desc, irq);
desc = irq_remap_to_desc(irq, desc);
/*
在多处理器的系统上，可能中断已经被另外一个CPU开始处理..但是该CPU也
进入到进入处理..此时另外处理的CPU会设置状态为正在处理当中..
因此，当前CPU就直接退出。
*/
if (unlikely(desc->status & IRQ_INPROGRESS))
goto out_unlock;
desc->status &= ~(IRQ_REPLAY | IRQ_WAITING);
kstat_incr_irqs_this_cpu(irq, desc);
/*
* If its disabled or no action available
* keep it masked and get out of here
*/
action = desc->action;
/*
如果该中断线上没有中断处理函数，那就直接退出.
或者说，该中断线当前状态是DISABLED，也就是要屏蔽掉该中断的..?
但是由于某种原因还产生了中断?不过确实状态就是DISABLED，那也直接退出。
*/
if (unlikely(!action || (desc->status & IRQ_DISABLED)))
goto out_unlock;
//好这里设置为正在处理当中...避免多处理的竞争...哦。这断代码的执行
//是在上锁的状态下的..下面解锁.
desc->status |= IRQ_INPROGRESS;
spin_unlock(&desc->lock);
action_ret = handle_IRQ_event(irq, action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
spin_lock(&desc->lock);
//处理完成之后..这里要修改当前中断线的状态了..一样是上锁.
desc->status &= ~IRQ_INPROGRESS;
//该中断线的状态是不屏蔽的，并且有unmask函数..那就调用unmask，它就是
//取消屏蔽该中断线...因为水平电流处理函数在一开始有mask_ack_irq给屏蔽掉了中断线了
if (!(desc->status & IRQ_DISABLED) && desc->chip->unmask)
desc->chip->unmask(irq);
out_unlock:
spin_unlock(&desc->lock);
}
irqreturn_t
handle_irq_event_percpu(struct irq_desc *desc, struct irqaction *action)
{
irqreturn_t retval = IRQ_NONE;
unsigned int flags = 0, irq = desc->irq_data.irq;
while (action) {
irqreturn_t res;
if(!action->handler) {
printk(KERN_WARNING "IRQ %d device %s get event "
"but no action handle function available.", irq, action->name);
action = action->next;
continue;
}
trace_irq_handler_entry(irq, action);
res = action->handler(irq, action->dev_id);
trace_irq_handler_exit(irq, action, res);
if (WARN_ONCE(!irqs_disabled(),"irq %u handler %pF enabled interrupts\n",
irq, action->handler))
local_irq_disable();
switch (res) {
case IRQ_WAKE_THREAD:
/*
* Catch drivers which return WAKE_THREAD but
* did not set up a thread function
*/
if (unlikely(!action->thread_fn)) {
warn_no_thread(irq, action);
break;
}
irq_wake_thread(desc, action);
/* Fall through to add to randomness */
case IRQ_HANDLED:
flags |= action->flags;
break;
default:
break;
}
retval |= res;
action = action->next;
}
add_interrupt_randomness(irq, flags);
if (!noirqdebug)
note_interrupt(irq, desc, retval);
return retval;
}
/**
* handle_fasteoi_irq - irq handler for transparent controllers
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Only a single callback will be issued to the chip: an ->eoi()
* call when the interrupt has been serviced. This enables support
* for modern forms of interrupt handlers, which handle the flow
* details in hardware, transparently.
*/
void
handle_fasteoi_irq(unsigned int irq, struct irq_desc *desc)
{
struct irqaction *action;
irqreturn_t action_ret;
raw_spin_lock(&desc->lock);
if (unlikely(desc->status & IRQ_INPROGRESS))
goto out;
desc->status &= ~(IRQ_REPLAY | IRQ_WAITING);
kstat_incr_irqs_this_cpu(irq, desc);
/*
* If its disabled or no action available
* then mask it and get out of here:
*/
action = desc->action;
if (unlikely(!action || (desc->status & IRQ_DISABLED))) {
desc->status |= IRQ_PENDING;
mask_irq(desc);
goto out;
}
if (desc->status & IRQ_ONESHOT)
mask_irq(desc);
desc->status |= IRQ_INPROGRESS;
desc->status &= ~IRQ_PENDING;
raw_spin_unlock(&desc->lock);
action_ret = handle_IRQ_event(irq, action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
raw_spin_lock(&desc->lock);
desc->status &= ~IRQ_INPROGRESS;
#ifdef CONFIG_IPIPE
if (!(desc->status & IRQ_MASKED))
desc->irq_data.chip->irq_unmask(&desc->irq_data);
out:
#else
out:
desc->irq_data.chip->irq_eoi(&desc->irq_data);
#endif
raw_spin_unlock(&desc->lock);
}
/**
* handle_percpu_irq - Per CPU local irq handler
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Per CPU interrupts on SMP machines without locking requirements
*/
void
handle_percpu_irq(unsigned int irq, struct irq_desc *desc)
{
irqreturn_t action_ret;
kstat_incr_irqs_this_cpu(irq, desc);
if (desc->irq_data.chip->irq_ack)
desc->irq_data.chip->irq_ack(&desc->irq_data);
action_ret = handle_IRQ_event(irq, desc->action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
if (desc->irq_data.chip->irq_eoi)
desc->irq_data.chip->irq_eoi(&desc->irq_data);
}
/**
* handle_percpu_IRQ - Per CPU local irq handler
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Per CPU interrupts on SMP machines without locking requirements
*/
void fastcall
handle_percpu_irq(unsigned int irq, struct irq_desc *desc)
{
irqreturn_t action_ret;
kstat_this_cpu.irqs[irq]++;
if (desc->chip->ack)
desc->chip->ack(irq);
action_ret = handle_IRQ_event(irq, desc->action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
if (desc->chip->eoi)
desc->chip->eoi(irq);
}
/**
* handle_percpu_IRQ - Per CPU local irq handler
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Per CPU interrupts on SMP machines without locking requirements
*/
void
handle_percpu_irq(unsigned int irq, struct irq_desc *desc)
{
irqreturn_t action_ret;
kstat_incr_irqs_this_cpu(irq, desc);
if (desc->chip->ack)
desc->chip->ack(irq);
action_ret = handle_IRQ_event(irq, desc->action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
if (desc->chip->eoi) {
desc->chip->eoi(irq);
desc = irq_remap_to_desc(irq, desc);
}
}
/**
* handle_fasteoi_irq - irq handler for transparent controllers
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Only a single callback will be issued to the chip: an ->eoi()
* call when the interrupt has been serviced. This enables support
* for modern forms of interrupt handlers, which handle the flow
* details in hardware, transparently.
*/
void fastcall
handle_fasteoi_irq(unsigned int irq, struct irq_desc *desc)
{
unsigned int cpu = smp_processor_id();
struct irqaction *action;
irqreturn_t action_ret;
spin_lock(&desc->lock);
if (unlikely(desc->status & IRQ_INPROGRESS))
goto out;
desc->status &= ~(IRQ_REPLAY | IRQ_WAITING);
kstat_cpu(cpu).irqs[irq]++;
/*
* If its disabled or no action available
* then mask it and get out of here:
*/
action = desc->action;
if (unlikely(!action || (desc->status & IRQ_DISABLED))) {
desc->status |= IRQ_PENDING;
if (desc->chip->mask)
desc->chip->mask(irq);
goto out;
}
desc->status |= IRQ_INPROGRESS;
desc->status &= ~IRQ_PENDING;
spin_unlock(&desc->lock);
action_ret = handle_IRQ_event(irq, action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
spin_lock(&desc->lock);
desc->status &= ~IRQ_INPROGRESS;
out:
desc->chip->eoi(irq);
spin_unlock(&desc->lock);
}
/**
* handle_level_irq - Level type irq handler
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Level type interrupts are active as long as the hardware line has
* the active level. This may require to mask the interrupt and unmask
* it after the associated handler has acknowledged the device, so the
* interrupt line is back to inactive.
*/
void
handle_level_irq(unsigned int irq, struct irq_desc *desc)
{
struct irqaction *action;
irqreturn_t action_ret;
spin_lock(&desc->lock);
mask_ack_irq(desc, irq);
if (unlikely(desc->status & IRQ_INPROGRESS))
goto out_unlock;
desc->status &= ~(IRQ_REPLAY | IRQ_WAITING);
kstat_incr_irqs_this_cpu(irq, desc);
/*
* If its disabled or no action available
* keep it masked and get out of here
*/
action = desc->action;
if (unlikely(!action || (desc->status & IRQ_DISABLED)))
{
printk(KERN_ERR "IRQ %d enter bad status!\n", irq);
goto out_unlock;
}
desc->status |= IRQ_INPROGRESS;
spin_unlock(&desc->lock);
action_ret = handle_IRQ_event(irq, action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
spin_lock(&desc->lock);
desc->status &= ~IRQ_INPROGRESS;
if (unlikely(desc->status & IRQ_ONESHOT))
desc->status |= IRQ_MASKED;
else if (!(desc->status & IRQ_DISABLED) && desc->chip->unmask)
desc->chip->unmask(irq);
out_unlock:
spin_unlock(&desc->lock);
}
static void pcap_isr_work(struct work_struct *work)
{
struct pcap_chip *pcap = container_of(work, struct pcap_chip, isr_work);
struct pcap_platform_data *pdata = pcap->spi->dev.platform_data;
u32 msr, isr, int_sel, service;
int irq;
do {
ezx_pcap_read(pcap, PCAP_REG_MSR, &msr);
ezx_pcap_read(pcap, PCAP_REG_ISR, &isr);
/* We cant service/ack irqs that are assigned to port 2 */
if (!(pdata->config & PCAP_SECOND_PORT)) {
ezx_pcap_read(pcap, PCAP_REG_INT_SEL, &int_sel);
isr &= ~int_sel;
}
ezx_pcap_write(pcap, PCAP_REG_MSR, isr | msr);
ezx_pcap_write(pcap, PCAP_REG_ISR, isr);
local_irq_disable();
service = isr & ~msr;
for (irq = pcap->irq_base; service; service >>= 1, irq++) {
if (service & 1) {
struct irq_desc *desc = irq_to_desc(irq);
if (WARN(!desc, KERN_WARNING
"Invalid PCAP IRQ %d\n", irq))
break;
if (desc->status & IRQ_DISABLED)
note_interrupt(irq, desc, IRQ_NONE);
else
desc->handle_irq(irq, desc);
}
}
local_irq_enable();
ezx_pcap_write(pcap, PCAP_REG_MSR, pcap->msr);
} while (gpio_get_value(irq_to_gpio(pcap->spi->irq)));
}
/**
* handle_level_irq - Level type irq handler
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Level type interrupts are active as long as the hardware line has
* the active level. This may require to mask the interrupt and unmask
* it after the associated handler has acknowledged the device, so the
* interrupt line is back to inactive.
*/
void
handle_level_irq(unsigned int irq, struct irq_desc *desc)
{
struct irqaction *action;
irqreturn_t action_ret;
raw_spin_lock(&desc->lock);
#ifndef CONFIG_IPIPE
mask_ack_irq(desc);
#endif
if (unlikely(desc->status & IRQ_INPROGRESS))
goto out_unlock;
desc->status &= ~(IRQ_REPLAY | IRQ_WAITING);
kstat_incr_irqs_this_cpu(irq, desc);
/*
* If its disabled or no action available
* keep it masked and get out of here
*/
action = desc->action;
if (unlikely(!action || (desc->status & IRQ_DISABLED)))
goto out_unlock;
desc->status |= IRQ_INPROGRESS;
raw_spin_unlock(&desc->lock);
action_ret = handle_IRQ_event(irq, action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
raw_spin_lock(&desc->lock);
desc->status &= ~IRQ_INPROGRESS;
if (!(desc->status & (IRQ_DISABLED | IRQ_ONESHOT)))
unmask_irq(desc);
out_unlock:
raw_spin_unlock(&desc->lock);
}
/*
* handle_nested_irq - Handle a nested irq from a irq thread
* @irq: the interrupt number
*
* Handle interrupts which are nested into a threaded interrupt
* handler. The handler function is called inside the calling
* threads context.
*/
void handle_nested_irq(unsigned int irq)
{
struct irq_desc *desc = irq_to_desc(irq);
struct irqaction *action;
int mask_this_irq = 0;
irqreturn_t action_ret;
might_sleep();
raw_spin_lock_irq(&desc->lock);
kstat_incr_irqs_this_cpu(irq, desc);
action = desc->action;
if (unlikely(!action || (desc->status & IRQ_DISABLED))) {
mask_this_irq = 1;
if (!(desc->status & IRQ_LEVEL))
desc->status |= IRQ_PENDING;
goto out_unlock;
}
desc->status |= IRQ_INPROGRESS;
raw_spin_unlock_irq(&desc->lock);
action_ret = action->thread_fn(action->irq, action->dev_id);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
raw_spin_lock_irq(&desc->lock);
desc->status &= ~IRQ_INPROGRESS;
out_unlock:
if (unlikely(mask_this_irq)) {
chip_bus_lock(irq, desc);
mask_irq(desc, irq);
chip_bus_sync_unlock(irq, desc);
}
raw_spin_unlock_irq(&desc->lock);
}
static void handle_prio_irq(unsigned int irq, struct irq_desc *desc)
{
unsigned int cpu = smp_processor_id();
struct irqaction *action;
irqreturn_t action_ret;
spin_lock(&desc->lock);
BUG_ON(desc->status & IRQ_INPROGRESS);
desc->status &= ~(IRQ_REPLAY | IRQ_WAITING);
kstat_cpu(cpu).irqs[irq]++;
action = desc->action;
if (unlikely(!action || (desc->status & IRQ_DISABLED)))
goto out_mask;
desc->status |= IRQ_INPROGRESS;
spin_unlock(&desc->lock);
action_ret = handle_IRQ_event(irq, action);
/* XXX: There is no direct way to access noirqdebug, so check
* unconditionally for spurious irqs...
* Maybe this function should go to kernel/irq/chip.c? */
note_interrupt(irq, desc, action_ret);
spin_lock(&desc->lock);
desc->status &= ~IRQ_INPROGRESS;
if (desc->status & IRQ_DISABLED)
out_mask:
desc->chip->mask(irq);
/* ack unconditionally to unmask lower prio irqs */
desc->chip->ack(irq);
spin_unlock(&desc->lock);
}
/**
* handle_level_irq - Level type irq handler
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Level type interrupts are active as long as the hardware line has
* the active level. This may require to mask the interrupt and unmask
* it after the associated handler has acknowledged the device, so the
* interrupt line is back to inactive.
*/
void
handle_level_irq(unsigned int irq, struct irq_desc *desc)
{
unsigned int cpu = smp_processor_id();
struct irqaction *action;
irqreturn_t action_ret;
spin_lock(&desc->lock);
mask_ack_irq(desc, irq);
if (unlikely(desc->status & IRQ_INPROGRESS))
goto out_unlock;
desc->status &= ~(IRQ_REPLAY | IRQ_WAITING);
kstat_cpu(cpu).irqs[irq]++;
/*
* If its disabled or no action available
* keep it masked and get out of here
*/
action = desc->action;
if (unlikely(!action || (desc->status & IRQ_DISABLED)))
goto out_unlock;
desc->status |= IRQ_INPROGRESS;
spin_unlock(&desc->lock);
action_ret = handle_IRQ_event(irq, action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
spin_lock(&desc->lock);
desc->status &= ~IRQ_INPROGRESS;
if (!(desc->status & IRQ_DISABLED) && desc->chip->unmask)
desc->chip->unmask(irq);
out_unlock:
spin_unlock(&desc->lock);
}
/*
* handle_nested_irq - Handle a nested irq from a irq thread
* @irq: the interrupt number
*
* Handle interrupts which are nested into a threaded interrupt
* handler. The handler function is called inside the calling
* threads context.
*/
void handle_nested_irq(unsigned int irq)
{
struct irq_desc *desc = irq_to_desc(irq);
struct irqaction *action;
int mask_this_irq = 0;
irqreturn_t action_ret;
might_sleep();
raw_spin_lock_irq(&desc->lock);
kstat_incr_irqs_this_cpu(irq, desc);
action = desc->action;
if (unlikely(!action || irqd_irq_disabled(&desc->irq_data))) {
mask_this_irq = 1;
goto out_unlock;
}
irqd_set(&desc->irq_data, IRQD_IRQ_INPROGRESS);
raw_spin_unlock_irq(&desc->lock);
action_ret = action->thread_fn(action->irq, action->dev_id);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
raw_spin_lock_irq(&desc->lock);
irqd_clear(&desc->irq_data, IRQD_IRQ_INPROGRESS);
out_unlock:
raw_spin_unlock_irq(&desc->lock);
if (unlikely(mask_this_irq)) {
chip_bus_lock(desc);
mask_irq(desc);
chip_bus_sync_unlock(desc);
}
}
irqreturn_t
handle_irq_event_percpu(struct irq_desc *desc, struct irqaction *action)
{
irqreturn_t retval = IRQ_NONE;
unsigned int flags = 0, irq = desc->irq_data.irq;
do {
irqreturn_t res;
#ifdef CONFIG_SEC_DEBUG_RT_THROTTLE_ACTIVE
unsigned long long start_time, end_time;
start_time = sec_debug_clock();
#endif
sec_debug_irq_log(irq, (void *)action->handler, 1);
trace_irq_handler_entry(irq, action);
exynos_ss_irq(irq, (void *)action->handler, (int)irqs_disabled(), ESS_FLAG_IN);
res = action->handler(irq, action->dev_id);
exynos_ss_irq(irq, (void *)action->handler, (int)irqs_disabled(), ESS_FLAG_OUT);
trace_irq_handler_exit(irq, action, res);
sec_debug_irq_log(irq, (void *)action->handler, 2);
#ifdef CONFIG_SEC_DEBUG_RT_THROTTLE_ACTIVE
end_time = sec_debug_clock();
if (start_time + 950000000 < end_time) {
sec_debug_aux_log(SEC_DEBUG_AUXLOG_IRQ, "I:%llu %pf", start_time, action->handler);
}
#endif
if (WARN_ONCE(!irqs_disabled(),"irq %u handler %pF enabled interrupts\n",
irq, action->handler))
local_irq_disable();
switch (res) {
case IRQ_WAKE_THREAD:
/*
* Catch drivers which return WAKE_THREAD but
* did not set up a thread function
*/
if (unlikely(!action->thread_fn)) {
warn_no_thread(irq, action);
break;
}
irq_wake_thread(desc, action);
/* Fall through to add to randomness */
case IRQ_HANDLED:
flags |= action->flags;
break;
default:
break;
}
retval |= res;
action = action->next;
} while (action);
add_interrupt_randomness(irq, flags);
if (!noirqdebug)
note_interrupt(irq, desc, retval);
return retval;
}
/**
* __do_IRQ - original all in one highlevel IRQ handler
* @irq: the interrupt number
*
* __do_IRQ handles all normal device IRQ's (the special
* SMP cross-CPU interrupts have their own specific
* handlers).
*
* This is the original x86 implementation which is used for every
* interrupt type.
*/
unsigned int __do_IRQ(unsigned int irq)
{
struct irq_desc *desc = irq_to_desc(irq);
struct irqaction *action;
unsigned int status;
kstat_incr_irqs_this_cpu(irq, desc);
if (CHECK_IRQ_PER_CPU(desc->status)) {
irqreturn_t action_ret;
/*
* No locking required for CPU-local interrupts:
*/
if (desc->chip->ack)
desc->chip->ack(irq);
if (likely(!(desc->status & IRQ_DISABLED))) {
action_ret = handle_IRQ_event(irq, desc->action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
}
desc->chip->end(irq);
return 1;
}
spin_lock(&desc->lock);
if (desc->chip->ack)
desc->chip->ack(irq);
/*
* REPLAY is when Linux resends an IRQ that was dropped earlier
* WAITING is used by probe to mark irqs that are being tested
*/
status = desc->status & ~(IRQ_REPLAY | IRQ_WAITING);
status |= IRQ_PENDING; /* we _want_ to handle it */
/*
* If the IRQ is disabled for whatever reason, we cannot
* use the action we have.
*/
action = NULL;
if (likely(!(status & (IRQ_DISABLED | IRQ_INPROGRESS)))) {
action = desc->action;
status &= ~IRQ_PENDING; /* we commit to handling */
status |= IRQ_INPROGRESS; /* we are handling it */
}
desc->status = status;
/*
* If there is no IRQ handler or it was disabled, exit early.
* Since we set PENDING, if another processor is handling
* a different instance of this same irq, the other processor
* will take care of it.
*/
if (unlikely(!action))
goto out;
/*
* Edge triggered interrupts need to remember
* pending events.
* This applies to any hw interrupts that allow a second
* instance of the same irq to arrive while we are in do_IRQ
* or in the handler. But the code here only handles the _second_
* instance of the irq, not the third or fourth. So it is mostly
* useful for irq hardware that does not mask cleanly in an
* SMP environment.
*/
for (;;) {
irqreturn_t action_ret;
spin_unlock(&desc->lock);
action_ret = handle_IRQ_event(irq, action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
spin_lock(&desc->lock);
if (likely(!(desc->status & IRQ_PENDING)))
break;
desc->status &= ~IRQ_PENDING;
}
desc->status &= ~IRQ_INPROGRESS;
out:
/*
* The ->end() handler has to deal with interrupts which got
* disabled while the handler was running.
*/
desc->chip->end(irq);
spin_unlock(&desc->lock);
return 1;
}
/**
* handle_edge_irq - edge type IRQ handler
* @irq: the interrupt number
* @desc: the interrupt description structure for this irq
*
* Interrupt occures on the falling and/or rising edge of a hardware
* signal. The occurence is latched into the irq controller hardware
* and must be acked in order to be reenabled. After the ack another
* interrupt can happen on the same source even before the first one
* is handled by the assosiacted event handler. If this happens it
* might be necessary to disable (mask) the interrupt depending on the
* controller hardware. This requires to reenable the interrupt inside
* of the loop which handles the interrupts which have arrived while
* the handler was running. If all pending interrupts are handled, the
* loop is left.
*/
void
handle_edge_irq(unsigned int irq, struct irq_desc *desc)
{
spin_lock(&desc->lock);
/*
需要同水平电流处理函数对比，这里并没有调用mask_ack函数，来屏蔽中断线.
*/
desc->status &= ~(IRQ_REPLAY | IRQ_WAITING);
/*
* If we're currently running this IRQ, or its disabled,
* we shouldn't process the IRQ. Mark it pending, handle
* the necessary masking and go out
*/
/*
如果边缘电平的触发，然后引起了一个中断，处理函数会对该中断线设置为正在处理当中.
也就是IRQ_INPROGRESS标记..此时判断判断IRQ_INPROGRESS如果置位，代表是又一个中断发生了
因为是边缘触发的..那就设置status为PENDING挂机，等待处理.
*/
if (unlikely((desc->status & (IRQ_INPROGRESS | IRQ_DISABLED)) ||
!desc->action)) {
desc->status |= (IRQ_PENDING | IRQ_MASKED);
//已经PENDING了一次处理，这时候特殊处理，屏蔽掉该中断..然后应答该中断线.
//上面status设置为IRQ_MASKED，也可以证实这个情况.
mask_ack_irq(desc, irq);
desc = irq_remap_to_desc(irq, desc);
goto out_unlock;
}
kstat_incr_irqs_this_cpu(irq, desc);
/*
当然..更一般的情况是下面这种...它会调用应答ack.!!注意注意...和水平触发的区别来了.
水平触发是mask_ack!!!
*/
/* Start handling the irq */
if (desc->chip->ack)
desc->chip->ack(irq);
desc = irq_remap_to_desc(irq, desc);
/* Mark the IRQ currently in progress.*/
desc->status |= IRQ_INPROGRESS;
do {
struct irqaction *action = desc->action;
irqreturn_t action_ret;
//如果该中断线没有中断处理函数..那屏蔽掉该中断线..然后退出.
if (unlikely(!action)) {
desc->chip->mask(irq);
goto out_unlock;
}
/*
* When another irq arrived while we were handling
* one, we could have masked the irq.
* Renable it, if it was not disabled in meantime.
*/
if (unlikely((desc->status &
(IRQ_PENDING | IRQ_MASKED | IRQ_DISABLED)) ==
(IRQ_PENDING | IRQ_MASKED))) {
//前面有看到..到中断处理过程中再次引起中断，就会挂机该中断，然后屏蔽中断线.
//此时这里，就是重新设置为不屏蔽的..
desc->chip->unmask(irq);
desc->status &= ~IRQ_MASKED;
}
desc->status &= ~IRQ_PENDING;
spin_unlock(&desc->lock);
//释放锁...进入到处理中断函数中去.
action_ret = handle_IRQ_event(irq, action);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret);
//中断处理函数处理完成了...然后还要继续判断在处理过程中是否有新的中断产生.
spin_lock(&desc->lock);
//因为对于边缘触发的中断来说，它的处理过程，可能有引起了中断了的发生了.
//此时会设置status带IRQ_PENDING标记.那就需要在继续执行一遍处理函数.
} while ((desc->status & (IRQ_PENDING | IRQ_DISABLED)) == IRQ_PENDING);
desc->status &= ~IRQ_INPROGRESS;
out_unlock:
spin_unlock(&desc->lock);
}
/*
* This thread processes interrupts reported by the Primary Interrupt Handler.
*/
static int twl6030_irq_thread(void *data)
{
long irq = (long)data;
static unsigned i2c_errors;
static const unsigned max_i2c_errors = 100;
int ret;
current->flags |= PF_NOFREEZE;
while (!kthread_should_stop()) {
int i;
union {
u8 bytes[4];
u32 int_sts;
} sts;
/* Wait for IRQ, then read PIH irq status (also blocking) */
wait_for_completion_interruptible(&irq_event);
/* read INT_STS_A, B and C in one shot using a burst read */
ret = twl_i2c_read(TWL_MODULE_PIH, sts.bytes,
REG_INT_STS_A, 3);
if (ret) {
pr_warning("twl6030: I2C error %d reading PIH ISR\n",
ret);
if (++i2c_errors >= max_i2c_errors) {
printk(KERN_ERR "Maximum I2C error count"
" exceeded. Terminating %s.\n",
__func__);
break;
}
complete(&irq_event);
continue;
}
sts.bytes[3] = 0; /* Only 24 bits are valid*/
for (i = 0; sts.int_sts; sts.int_sts >>= 1, i++) {
local_irq_disable();
if (sts.int_sts & 0x1) {
int module_irq = twl6030_irq_base +
twl6030_interrupt_mapping[i];
struct irq_desc *d = irq_to_desc(module_irq);
if (!d) {
pr_err("twl6030: Invalid SIH IRQ: %d\n",
module_irq);
return -EINVAL;
}
/* These can't be masked ... always warn
* if we get any surprises.
*/
if (d->status & IRQ_DISABLED)
note_interrupt(module_irq, d,
IRQ_NONE);
else
d->handle_irq(module_irq, d);
}
local_irq_enable();
}
ret = twl_i2c_write(TWL_MODULE_PIH, sts.bytes,
REG_INT_STS_A, 3); /* clear INT_STS_A */
if (ret)
pr_warning("twl6030: I2C error in clearing PIH ISR\n");
enable_irq(irq);
}
return 0;
}
irqreturn_t
handle_irq_event_percpu(struct irq_desc *desc, struct irqaction *action)
{
irqreturn_t retval = IRQ_NONE;
unsigned int random = 0, irq = desc->irq_data.irq;
#ifdef CONFIG_MSM_SM_EVENT
sm_msm_irq_data_t sm_irq;
#endif
if (irq==32) //the smd dev irq is 32
{
smd_irq_stamp[smd_irq_stamp_index++] = jiffies;
smd_irq_stamp_index = smd_irq_stamp_index & (MAX_SMD_IRQ_STAMP_NUM - 1 );
}
last_irq_stamp = jiffies;
do {
irqreturn_t res;
trace_irq_handler_entry(irq, action);
#ifdef CONFIG_MSM_SM_EVENT
sm_irq.func_addr = (unsigned int)action->handler;
sm_irq.irq_num = irq;
sm_add_event(SM_IRQ_EVENT | IRQ_EVENT_ENTER,
SM_EVENT_START, 0, &sm_irq, sizeof(sm_msm_irq_data_t));
#endif
res = action->handler(irq, action->dev_id);
trace_irq_handler_exit(irq, action, res);
/*
#ifdef CONFIG_MSM_SM_EVENT
sm_add_event(SM_IRQ_EVENT | IRQ_EVENT_LEAVE,
SM_EVENT_END, 0, &sm_irq, sizeof(sm_msm_irq_data_t));
#endif
*/
if (WARN_ONCE(!irqs_disabled(),"irq %u handler %pF enabled interrupts\n",
irq, action->handler))
local_irq_disable();
switch (res) {
case IRQ_WAKE_THREAD:
/*
* Catch drivers which return WAKE_THREAD but
* did not set up a thread function
*/
if (unlikely(!action->thread_fn)) {
warn_no_thread(irq, action);
break;
}
irq_wake_thread(desc, action);
/* Fall through to add to randomness */
case IRQ_HANDLED:
random |= action->flags;
break;
default:
break;
}
retval |= res;
action = action->next;
} while (action);
if (random & IRQF_SAMPLE_RANDOM)
add_interrupt_randomness(irq);
if (!noirqdebug)
note_interrupt(irq, desc, retval);
return retval;
}
/**
* __do_IRQ - original all in one highlevel IRQ handler
* @irq: the interrupt number
* @regs: pointer to a register structure
*
* __do_IRQ handles all normal device IRQ's (the special
* SMP cross-CPU interrupts have their own specific
* handlers).
*
* This is the original x86 implementation which is used for every
* interrupt type.
*/
fastcall notrace unsigned int __do_IRQ(unsigned int irq, struct pt_regs *regs)
{
struct irq_desc *desc = irq_desc + irq;
struct irqaction *action;
unsigned int status;
kstat_this_cpu.irqs[irq]++;
if (CHECK_IRQ_PER_CPU(desc->status)) {
irqreturn_t action_ret;
/*
* No locking required for CPU-local interrupts:
*/
if (desc->chip->ack)
desc->chip->ack(irq);
action_ret = handle_IRQ_event(irq, regs, desc->action);
desc->chip->end(irq);
return 1;
}
/*
* If the task is currently running in user mode, don't
* detect soft lockups. If CONFIG_DETECT_SOFTLOCKUP is not
* configured, this should be optimized out.
*/
if (user_mode(regs))
touch_softlockup_watchdog();
spin_lock(&desc->lock);
if (desc->chip->ack)
desc->chip->ack(irq);
/*
* REPLAY is when Linux resends an IRQ that was dropped earlier
* WAITING is used by probe to mark irqs that are being tested
*/
status = desc->status & ~(IRQ_REPLAY | IRQ_WAITING);
status |= IRQ_PENDING; /* we _want_ to handle it */
/*
* If the IRQ is disabled for whatever reason, we cannot
* use the action we have.
*/
action = NULL;
if (likely(!(status & (IRQ_DISABLED | IRQ_INPROGRESS)))) {
action = desc->action;
status &= ~IRQ_PENDING; /* we commit to handling */
status |= IRQ_INPROGRESS; /* we are handling it */
}
desc->status = status;
/*
* If there is no IRQ handler or it was disabled, exit early.
* Since we set PENDING, if another processor is handling
* a different instance of this same irq, the other processor
* will take care of it.
*/
if (unlikely(!action))
goto out;
/*
* hardirq redirection to the irqd process context:
*/
if (redirect_hardirq(desc))
goto out_no_end;
/*
* Edge triggered interrupts need to remember
* pending events.
* This applies to any hw interrupts that allow a second
* instance of the same irq to arrive while we are in do_IRQ
* or in the handler. But the code here only handles the _second_
* instance of the irq, not the third or fourth. So it is mostly
* useful for irq hardware that does not mask cleanly in an
* SMP environment.
*/
for (;;) {
irqreturn_t action_ret;
spin_unlock(&desc->lock);
action_ret = handle_IRQ_event(irq, regs, action);
spin_lock(&desc->lock);
if (!noirqdebug)
note_interrupt(irq, desc, action_ret, regs);
if (likely(!(desc->status & IRQ_PENDING)))
break;
desc->status &= ~IRQ_PENDING;
}
desc->status &= ~IRQ_INPROGRESS;
out:
/*
* The ->end() handler has to deal with interrupts which got
* disabled while the handler was running.
*/
desc->chip->end(irq);
out_no_end:
spin_unlock(&desc->lock);
return 1;
}
irqreturn_t
handle_irq_event_percpu(struct irq_desc *desc, struct irqaction *action)
{
irqreturn_t retval = IRQ_NONE;
unsigned int random = 0, irq = desc->irq_data.irq;
#ifdef CONFIG_MTPROF_IRQ_DURATION
unsigned long long t1, t2, dur;
#ifdef CONFIG_ISR_MONITOR
char aee_str[40];
#endif
#endif
do {
irqreturn_t res;
trace_irq_handler_entry(irq, action);
#ifdef CONFIG_MTPROF_IRQ_DURATION
t1 = sched_clock();
res = action->handler(irq, action->dev_id);
t2 = sched_clock();
dur = t2 - t1;
action->duration += dur;
action->count++;
action->dur_max = max(dur,action->dur_max);
action->dur_min = min(dur,action->dur_min);
#ifdef CONFIG_MTPROF_CPUTIME
if(mtsched_enabled == 1)
{
int isr_find = 0;
struct mtk_isr_info *mtk_isr_point = current->se.mtk_isr;
struct mtk_isr_info *mtk_isr_current = mtk_isr_point;
char *isr_name = NULL;
current->se.mtk_isr_time += dur;
while(mtk_isr_point != NULL)
{
if(mtk_isr_point->isr_num == irq)
{
mtk_isr_point->isr_time += dur;
mtk_isr_point->isr_count++;
isr_find = 1;
break;
}
mtk_isr_current = mtk_isr_point;
mtk_isr_point = mtk_isr_point -> next;
}
if(isr_find == 0)
{
mtk_isr_point = kmalloc(sizeof(struct mtk_isr_info), GFP_ATOMIC);
if(mtk_isr_point == NULL)
{
printk(KERN_ERR"cant' alloc mtk_isr_info mem!\n");
}
else
{
mtk_isr_point->isr_num = irq;
mtk_isr_point->isr_time = dur;
mtk_isr_point->isr_count = 1;
mtk_isr_point->next = NULL;
if(mtk_isr_current == NULL)
{
current->se.mtk_isr = mtk_isr_point;
}
else
{
mtk_isr_current->next = mtk_isr_point;
}
isr_name = kmalloc(sizeof(action->name),GFP_ATOMIC);
if(isr_name != NULL)
{
strcpy(isr_name, action->name);
mtk_isr_point->isr_name = isr_name;
}
else
{
printk(KERN_ERR"cant' alloc isr_name mem!\n");
}
current->se.mtk_isr_count++;
}
}
}
#endif
#ifdef CONFIG_ISR_MONITOR
if(unlikely(dur>TIME_3MS)){
if(in_white_list(irq)){
printk("[ISR Monitor] Warning! ISR%d:%s too long, %llu ns > 3 ms, t1:%llu, t2:%llu\n", irq, action->name, dur, t1, t2);
}else if(dur>TIME_6MS){
sprintf( aee_str, "ISR#%d:%s too long>6ms\n", irq, action->name);
aee_kernel_exception( aee_str,"isr_monitor\n");
printk("[ISR Monitor] Warning! ISR%d:%s too long, %llu ns > 10 ms, t1:%llu, t2:%llu\n", irq, action->name, dur, t1, t2);
}else{
sprintf( aee_str, "ISR#%d:%s too long>3ms\n", irq, action->name);
aee_kernel_warning( aee_str,"isr_monitor\n");
printk("[ISR Monitor] Warning! ISR%d:%s too long, %llu ns > 3 ms, t1:%llu, t2:%llu\n", irq, action->name, dur, t1, t2);
}
}
#endif
#else
res = action->handler(irq, action->dev_id);
#endif
trace_irq_handler_exit(irq, action, res);
if (WARN_ONCE(!irqs_disabled(),"irq %u handler %pF enabled interrupts\n",
irq, action->handler))
local_irq_disable();
switch (res) {
case IRQ_WAKE_THREAD:
/*
* Catch drivers which return WAKE_THREAD but
* did not set up a thread function
*/
if (unlikely(!action->thread_fn)) {
warn_no_thread(irq, action);
break;
}
irq_wake_thread(desc, action);
/* Fall through to add to randomness */
case IRQ_HANDLED:
random |= action->flags;
break;
default:
break;
}
retval |= res;
action = action->next;
} while (action);
if (random & IRQF_SAMPLE_RANDOM)
add_interrupt_randomness(irq);
if (!noirqdebug)
note_interrupt(irq, desc, retval);
return retval;
}
/*
* This thread processes interrupts reported by the Primary Interrupt Handler.
*/
static int twl6030_irq_thread(void *data)
{
long irq = (long)data;
static unsigned i2c_errors;
static const unsigned max_i2c_errors = 100;
int ret;
current->flags |= PF_NOFREEZE;
while (!kthread_should_stop()) {
int i;
int start_time = 0;
union {
u8 bytes[4];
u32 int_sts;
} sts;
/* Wait for IRQ, then read PIH irq status (also blocking) */
wait_for_completion_interruptible(&irq_event);
/* read INT_STS_A, B and C in one shot using a burst read */
ret = twl_i2c_read(TWL_MODULE_PIH, sts.bytes,
REG_INT_STS_A, 3);
if (ret) {
pr_warning("twl6030: I2C error %d reading PIH ISR\n",
ret);
if (++i2c_errors >= max_i2c_errors) {
printk(KERN_ERR "Maximum I2C error count"
" exceeded. Terminating %s.\n",
__func__);
break;
}
complete(&irq_event);
continue;
}
sts.bytes[3] = 0; /* Only 24 bits are valid*/
/*
* Since VBUS status bit is not reliable for VBUS disconnect
* use CHARGER VBUS detection status bit instead.
*/
if (sts.bytes[2] & 0x10)
sts.bytes[2] |= 0x08;
for (i = 0; sts.int_sts; sts.int_sts >>= 1, i++) {
local_irq_disable();
if (sts.int_sts & 0x1) {
int module_irq = twl6030_irq_base +
twl6030_interrupt_mapping[i];
struct irq_desc *d = irq_to_desc(module_irq);
if (!d) {
pr_err("twl6030: Invalid SIH IRQ: %d\n",
module_irq);
return -EINVAL;
}
/* this may be a wakeup event
* d->status flag's are masked while we are
* waking up, give some time for the
* IRQ to be enabled.
*/
start_time = jiffies;
while ((d->status & IRQ_DISABLED) &&
(jiffies_to_msecs(jiffies-start_time) < 100)) {
yield();
}
/* These can't be masked ... always warn
* if we get any surprises.
*/
if (d->status & IRQ_DISABLED) {
pr_warning("twl handler not called, irq is disabled!\n");
note_interrupt(module_irq, d,
IRQ_NONE);
}
else
d->handle_irq(module_irq, d);
}
local_irq_enable();
}
ret = twl_i2c_write(TWL_MODULE_PIH, sts.bytes,
REG_INT_STS_A, 3); /* clear INT_STS_A */
if (ret)
pr_warning("twl6030: I2C error in clearing PIH ISR\n");
enable_irq(irq);
}
return 0;
}
