/** Addresses are 7 bit - that is, between 0 and 0x7F. sendStop is whether to send a stop bit or not */
void jshI2CWrite(IOEventFlags device, unsigned char address, int nBytes, const unsigned char *data, bool sendStop) {
const nrf_drv_twi_t *twi = jshGetTWI(device);
if (!twi) return;
uint32_t err_code = nrf_drv_twi_tx(twi, address, data, nBytes, !sendStop);
if (err_code != NRF_SUCCESS)
jsExceptionHere(JSET_INTERNALERROR, "I2C Write Error %d\n", err_code);
}
/**
* @brief TWI events handler.
*/
void twi_handler(nrf_drv_twi_evt_t const * p_event, void * p_context) {
uint32_t err_code;
uint8_t reg[2];
NRF_LOG_DEBUG("twi_handler %u\n\r",p_event->type);
switch (p_event->type) {
case NRF_DRV_TWI_EVT_DONE:
NRF_LOG_DEBUG("twi_handler NRF_DRV_TWI_EVT_DONE %u\n\r",p_event->xfer_desc.type);
if (p_event->xfer_desc.type == NRF_DRV_TWI_XFER_TX) {
NRF_LOG_DEBUG("twi_handler TX\n\r");
if (twi_read_mode==SI7021_REG_HUM_READ || twi_read_mode==SI7021_REG_TEMP_READ) {
err_code = nrf_drv_twi_rx(&my_twi_0, SI7021_ADDR, m_sample, sizeof(m_sample));
APP_ERROR_CHECK(err_code);
}
} else if (p_event->xfer_desc.type == NRF_DRV_TWI_XFER_RX) {
NRF_LOG_DEBUG("twi_handler RX %d,%d\n\r",m_sample[0],m_sample[1]);
if (twi_read_mode==SI7021_REG_HUM_READ) {
humRaw=(uint16_t)m_sample[0] << 8 |m_sample[1];
reg[0] = SI7021_REG_TEMP_READ;
twi_read_mode = reg[0];
NRF_LOG_DEBUG("nrf_drv_twi_tx %x %u\n\r",SI7021_ADDR,reg[0]);
err_code = nrf_drv_twi_tx(&my_twi_0, SI7021_ADDR, reg, 1, false);
APP_ERROR_CHECK(err_code);
} else if (twi_read_mode==SI7021_REG_TEMP_READ) {
humCent = (uint16_t)((12500 * humRaw) >> 16) - 600;
tempRaw = (uint16_t)m_sample[0] << 8 |m_sample[1];
tempCent = (uint16_t)((17572 * tempRaw) >> 16) - 4685;
NRF_LOG_INFO("Relative Humidity %x %d.%d%% Temp %x %d.%d°C \r",humRaw,humCent/100,humCent%100,tempRaw,tempCent/100,tempCent%100);
NRF_LOG_DEBUG("\r\n");
si7021_sensor_update(humRaw,tempRaw);
}
}
// must only be called after lps331ap_on has been called
void lps331ap_readPressure(float *pres) {
uint8_t command[1] = {PRESS_OUT_XL | AUTO_INCR};
nrf_drv_twi_tx(
m_instance,
SENSOR_ADDR,
command,
sizeof(command),
true
);
uint8_t pressure_data[3] = {0x00, 0x00, 0x00};
nrf_drv_twi_rx(
m_instance,
SENSOR_ADDR,
pressure_data,
sizeof(pressure_data),
false
);
float pressure = (0x00FFFFFF & (((uint32_t)pressure_data[2] << 16) |
((uint32_t) pressure_data[1] << 8) |
((uint32_t) pressure_data[0]))) / 4096.0;
*pres = pressure;
}
void si7021_read_RH(float *hum){
uint8_t command[] = {Meas_RH_No_Hold_Master};
ret_code_t ret_code;
nrf_drv_twi_tx(
m_instance,
TEMP_HUM_ADDR_THIS,
command,
sizeof(command),
true
);
uint8_t temp_hum_data[3] = {0, 0, 0};
do
{
ret_code =
nrf_drv_twi_rx(
m_instance,
TEMP_HUM_ADDR_THIS,
temp_hum_data,
sizeof(temp_hum_data),
false
);
} while (ret_code != NRF_SUCCESS);
float humidity = -6.0 + ((125.0 / (1 << 16)) * (((uint32_t) temp_hum_data[0] << 8) | ((uint32_t) temp_hum_data[1] & 0xf0)));
*hum = humidity;
}
void lps331ap_interrupt_enable_manual(bool high, bool low, bool latch_request) {
uint8_t command[2] = {INT_CFG_REG, 0x00};
if (high) {
//enable high
command[1] = 0x01;
}
if (low) {
//enable low
command[1] = command[1] | 0x02;
}
if (latch_request) {
command[1] = command[1] | 0x04;
}
nrf_drv_twi_tx(
m_instance,
SENSOR_ADDR,
command,
sizeof(command),
false
);
}
void si7021_heater_off(){
uint8_t reg_status[1] = {0x00};
si7021_read_user_reg(reg_status);
uint8_t data[1] = {reg_status[0] & HEATER_OFF};
uint8_t command[] =
{
Write_User_Reg_1,
data[0]
};
nrf_drv_twi_tx(
m_instance,
TEMP_HUM_ADDR_THIS,
command,
sizeof(command),
false
);
}
void lps331ap_interrupt_enable(bool latch_request) {
uint8_t data[1] = {0x00};
uint8_t command[2] = {INT_CFG_REG, 0x00};
lps331ap_read_controlreg3(data);
if (data[0] & 0x09) {
//enable high
command[1] = 0x01;
}
if (data[0] & 0x12) {
//enable low
command[1] = command[1] | 0x02;
}
if (latch_request) {
command[1] = command[1] | 0x04;
}
nrf_drv_twi_tx(
m_instance,
SENSOR_ADDR,
command,
sizeof(command),
false
);
}
void lps331ap_config_interrupt(interrupt_config interrupt_c_1, interrupt_config interrupt_c_2 , bool active_low) {
uint8_t command[2] =
{
CTRL_REG3,
interrupt_c_1 | (interrupt_c_2 << 3)
};
if(active_low) {
command[1] = command[1] | 0x80;
}
nrf_drv_twi_tx(
m_instance,
SENSOR_ADDR,
command,
sizeof(command),
false
);
uint8_t data[1] = {0x00};
lps331ap_read_controlreg3(data);
}
void si7021_config(si7021_meas_res_t res_mode){
uint8_t res1, res0;
uint8_t reg_status;
res1 = (res_mode & 0x2) << 6;
res0 = res_mode & 0x1;
si7021_read_user_reg(®_status);
uint8_t data[1] = {reg_status | res1 | res0};
uint8_t command[] =
{
Write_User_Reg_1,
data[0]
};
nrf_drv_twi_tx(
m_instance,
TEMP_HUM_ADDR_THIS,
command,
sizeof(command),
false
);
}
//does not return correct temperature
void lps331ap_readTemp (float *temp) {
uint8_t command[1] = {TEMP_OUT_L | AUTO_INCR};
nrf_drv_twi_tx(
m_instance,
SENSOR_ADDR,
command,
sizeof(command),
true
);
uint8_t temp_data[2];
nrf_drv_twi_rx(
m_instance,
SENSOR_ADDR,
temp_data,
sizeof(temp_data),
false
);
float temperature = (((int16_t)( 0x0000FFFF & ( ( (uint32_t) temp_data[1] << 8) | ((uint32_t) temp_data[0]) ) )) / 480.0 ) + 42.5;
*temp = temperature;
}
void si7021_read_temp(float *temp){
uint8_t command[] = {Meas_Temp_No_Hold_Master};
ret_code_t ret_code;
nrf_drv_twi_tx(
m_instance,
TEMP_HUM_ADDR_THIS,
command,
sizeof(command),
true
);
uint8_t temp_hum_data[3] = {0, 0, 0};
do
{
ret_code =
nrf_drv_twi_rx(
m_instance,
TEMP_HUM_ADDR_THIS,
temp_hum_data,
sizeof(temp_hum_data),
false
);
} while (ret_code != NRF_SUCCESS);
float temperature = -46.85 + (175.72 * (((uint32_t) temp_hum_data[0] << 8) | ((uint32_t) temp_hum_data[1] & 0xfc)) / (1 << 16));
*temp = temperature;
}
ret_code_t mpu6050_register_read(const nrf_drv_twi_t * twi, uint8_t register_address, uint8_t * destination, uint8_t number_of_bytes)
{
//bool transfer_succeeded;
uint32_t err_code;
err_code = nrf_drv_twi_tx(twi, MPU6050_DEFAULT_ADDRESS, ®ister_address, 1, false);
err_code = nrf_drv_twi_rx(twi, MPU6050_DEFAULT_ADDRESS, destination, number_of_bytes, false);
return err_code;
}
ret_code_t mpu6050_register_write(const nrf_drv_twi_t * twi, uint8_t register_address, uint8_t value)
{
uint8_t w2_data[2];
//uint32_t err_code;
w2_data[0] = register_address;
w2_data[1] = value;
//return twi_master_transfer(m_device_address, w2_data, 2, TWI_ISSUE_STOP);
return nrf_drv_twi_tx(twi, MPU6050_DEFAULT_ADDRESS, w2_data, sizeof(w2_data), false);
//APP_ERROR_CHECK(err_code);
}
void si7021_reset(){
uint8_t data[1] = {RESET};
nrf_drv_twi_tx(
m_instance,
TEMP_HUM_ADDR_THIS,
data,
sizeof(data),
false
);
}
void lps331ap_interrupt_disable_all() {
uint8_t command[2] = {INT_CFG_REG, 0x00};
nrf_drv_twi_tx(
m_instance,
SENSOR_ADDR,
command,
sizeof(command),
false
);
}
int i2c_write(i2c_t *obj, int address, const char *data, int length, int stop)
{
twi_info_t *twi_info = TWI_INFO(obj);
nrf_drv_twi_t const *twi = &m_twi_instances[TWI_IDX(obj)];
twi_info->transfer_finished = false;
ret_code_t ret_code = nrf_drv_twi_tx(twi, twi_address(address),
(uint8_t const *)data, length, (stop == 0));
if (ret_code != NRF_SUCCESS) {
return 0;
}
while (!twi_info->transfer_finished) {}
return nrf_drv_twi_data_count_get(twi);
}
void ready_rfid_shield(void){
nrf_drv_twi_tx(&twi_rfid, ADR_RFID_SLAVE, &rfid_init_array_1[0], sizeof(rfid_init_array_1), false);
nrf_delay_ms(3);
nrf_drv_twi_rx(&twi_rfid, ADR_RFID_SLAVE, &dummy_array[0], 7);
nrf_delay_ms(3);
nrf_drv_twi_rx(&twi_rfid, ADR_RFID_SLAVE, &dummy_array[0], 14);
nrf_delay_ms(3);
nrf_drv_twi_tx(&twi_rfid, ADR_RFID_SLAVE, &rfid_init_array_2[0], sizeof(rfid_init_array_2), false);
nrf_delay_ms(3);
nrf_drv_twi_rx(&twi_rfid, ADR_RFID_SLAVE, &dummy_array[0], 7);
nrf_delay_ms(3);
nrf_drv_twi_rx(&twi_rfid, ADR_RFID_SLAVE, &dummy_array[0], 9);
nrf_delay_ms(3);
nrf_drv_twi_tx(&twi_rfid, ADR_RFID_SLAVE, &rfid_init_array_3[0], sizeof(rfid_init_array_3), false);
nrf_delay_ms(3);
nrf_drv_twi_rx(&twi_rfid, ADR_RFID_SLAVE, &dummy_array[0], 7);
}
//resets everything
void lps331ap_power_off() {
uint8_t command[2] = {
CTRL_REG1,
POWER_OFF
};
nrf_drv_twi_tx(
m_instance,
SENSOR_ADDR,
command,
sizeof(command),
false
);
}
void lps331ap_config_data_rate(lps331ap_data_rate data_rate) {
uint8_t command[2] =
{
CTRL_REG1,
(data_rate << 4)
};
nrf_drv_twi_tx(
m_instance,
SENSOR_ADDR,
command,
sizeof(command),
false
);
}
void lps331ap_sw_reset_disable() {
uint8_t command[2] =
{
CTRL_REG2,
0x00
};
nrf_drv_twi_tx(
m_instance,
SENSOR_ADDR,
command,
sizeof(command),
false
);
}
/**
* @brief Function for main application entry.
*/
int main(void)
{
ret_code_t ret_code;
nrf_gpio_cfg_output(LED_1);
nrf_gpio_pin_set(LED_1);
nrf_gpio_cfg_output(LED_2);
nrf_gpio_pin_set(LED_2);
uart_config();
printf("\033[2J\033[;H\r\n* Example to find TWI devices connected to \r\n* the TWI bus and their addresses\r\n\r\n");
twi_init();
uint8_t dummy_data = 0x55;
// Itterate through all possible 7-bit TWI addresses
for(uint8_t i = 0; i <= 0x7F; i++)
{
device_address = i;
// Send dummy data. If a device is present on this particular address a TWI EVT_DONE event is
// received in the twi event handler and a message is printed to UART
ret_code = nrf_drv_twi_tx(&twi_instance, i, &dummy_data, 1, false);
APP_ERROR_CHECK(ret_code);
// Delay 10 ms to allow TWI transfer to complete and UART to print messages before starting new transfer
nrf_delay_ms(10);
}
if(device_found)
{
// Blinke LED_1 rapidly if device is found
while(true)
{
nrf_gpio_pin_toggle(LED_1);
nrf_delay_ms(1000);
}
}
else
{
// Disable LED_1 if device is NOT found
nrf_gpio_cfg_default(LED_1);
printf("*****************\n\rNO DEVICES FOUND!\r\n*****************\n\r");
while(true)
{
nrf_gpio_pin_toggle(LED_2);
nrf_delay_ms(100);;
}
}
}
void si7021_read_user_reg(uint8_t *reg_status){
uint8_t command[] = {Read_User_Reg_1};
nrf_drv_twi_tx(
m_instance,
TEMP_HUM_ADDR_THIS,
command,
sizeof(command),
true
);
nrf_drv_twi_rx(
m_instance,
TEMP_HUM_ADDR_THIS,
reg_status,
sizeof(reg_status),
false
);
}
void si7021_read_firmware_rev(uint8_t *buf){
uint8_t command[2] =
{
Read_Firm_Rev_1,
Read_Firm_Rev_2
};
nrf_drv_twi_tx(
m_instance,
TEMP_HUM_ADDR_THIS,
command,
sizeof(command),
true
);
nrf_drv_twi_rx(
m_instance,
TEMP_HUM_ADDR_THIS,
buf,
sizeof(buf),
false
);
}
void si7021_read_temp_after_RH(float *temp){
uint8_t command[] = {Read_Temp_From_Prev_RH};
nrf_drv_twi_tx(
m_instance,
TEMP_HUM_ADDR_THIS,
command,
sizeof(command),
true
);
uint8_t temp_hum_data[3] = {0, 0, 0};
nrf_drv_twi_rx(
m_instance,
TEMP_HUM_ADDR_THIS,
temp_hum_data,
sizeof(temp_hum_data),
false
);
float temperature = -46.85 + (175.72 * (((uint32_t) temp_hum_data[0] << 8) | ((uint32_t) temp_hum_data[1] & 0xfc)) / (1 << 16));
*temp = temperature;
}
void si7021_read_temp_hold(float * temp){
uint8_t command[] = {Meas_Temp_Hold_Master};
nrf_drv_twi_tx(
m_instance,
TEMP_HUM_ADDR_THIS,
command,
sizeof(command),
true
);
uint8_t temp_hum_data[3] = {0x00, 0x00, 0x00};
nrf_drv_twi_rx(
m_instance,
TEMP_HUM_ADDR_THIS,
temp_hum_data,
sizeof(temp_hum_data),
false
);
float temperature = -46.85 + (175.72 * (((uint32_t) temp_hum_data[0] << 8) | ((uint32_t) temp_hum_data[1] & 0xfc)) / (1 << 16));
*temp = temperature;
}
void lps331ap_amp_control(bool selmain) {
uint8_t command[2] = {
AMP_CTRL,
0x00
};
if (selmain) {
command[2] = 0x01;
}
nrf_drv_twi_tx(
m_instance,
SENSOR_ADDR,
command,
sizeof(command),
false
);
}
{
return err_code;
}
return NRF_SUCCESS;
}
ret_code_t mcp4725_set_voltage(uint16_t val, bool write_eeprom)
{
/* Shift parameter val to get 2 8-bits values. */
uint8_t reg[3] = {write_eeprom ? MCP4725_EEPROM_ADDRESS : MCP4725_DAC_ADDRESS,
(val>>4), (val<<4)};
m_xfer_done = false;
ret_code_t err_code = nrf_drv_twi_tx(&m_twi, MCP4725_BASE_ADDRESS, reg, sizeof(reg), false);
if (err_code != NRF_SUCCESS)
{
return err_code;
}
while (m_xfer_done == false);
return NRF_SUCCESS;
}
bool mcp4725_is_busy(void)
{
uint8_t busy;
m_read_done = false;