static void __init omap3_evm_init(void)
{
struct omap_board_mux *obm;
omap3_evm_get_revision();
regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
obm = (cpu_is_omap3630()) ? omap36x_board_mux : omap35x_board_mux;
omap3_mux_init(obm, OMAP_PACKAGE_CBB);
omap_mux_init_gpio(63, OMAP_PIN_INPUT);
omap_hsmmc_init(mmc);
if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
omap3evm_twldata.vaux2 = &omap3evm_vaux2;
omap3_evm_i2c_init();
omap_display_init(&omap3_evm_dss_data);
omap_serial_init();
omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL);
/* OMAP3EVM uses ISP1504 phy and so register nop transceiver */
usb_nop_xceiv_register();
if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) {
/* enable EHCI VBUS using GPIO22 */
omap_mux_init_gpio(OMAP3_EVM_EHCI_VBUS, OMAP_PIN_INPUT_PULLUP);
/* Select EHCI port on main board */
omap_mux_init_gpio(OMAP3_EVM_EHCI_SELECT,
OMAP_PIN_INPUT_PULLUP);
gpio_request_array(omap3_evm_ehci_gpios,
ARRAY_SIZE(omap3_evm_ehci_gpios));
/* setup EHCI phy reset config */
omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP);
usbhs_bdata.reset_gpio_port[1] = 21;
/* EVM REV >= E can supply 500mA with EXTVBUS programming */
musb_board_data.power = 500;
musb_board_data.extvbus = 1;
} else {
/* setup EHCI phy reset on MDC */
omap_mux_init_gpio(135, OMAP_PIN_OUTPUT);
usbhs_bdata.reset_gpio_port[1] = 135;
}
usb_musb_init(&musb_board_data);
usbhs_init(&usbhs_bdata);
omap_nand_flash_init(NAND_BUSWIDTH_16, omap3evm_nand_partitions,
ARRAY_SIZE(omap3evm_nand_partitions));
omap_ads7846_init(1, OMAP3_EVM_TS_GPIO, 310, NULL);
omap3evm_init_smsc911x();
omap3_evm_display_init();
omap3_evm_wl12xx_init();
omap_twl4030_audio_init("omap3evm");
}
static void __init omap3_evm_init(void)
{
omap3_evm_get_revision();
if (cpu_is_omap3630())
omap3_mux_init(omap36x_board_mux, OMAP_PACKAGE_CBB);
else
omap3_mux_init(omap35x_board_mux, OMAP_PACKAGE_CBB);
omap_board_config = omap3_evm_config;
omap_board_config_size = ARRAY_SIZE(omap3_evm_config);
omap3_evm_i2c_init();
omap_display_init(&omap3_evm_dss_data);
omap_serial_init();
omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL);
/* OMAP3EVM uses ISP1504 phy and so register nop transceiver */
usb_nop_xceiv_register();
if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) {
/* enable EHCI VBUS using GPIO22 */
omap_mux_init_gpio(OMAP3_EVM_EHCI_VBUS, OMAP_PIN_INPUT_PULLUP);
/* Select EHCI port on main board */
omap_mux_init_gpio(OMAP3_EVM_EHCI_SELECT,
OMAP_PIN_INPUT_PULLUP);
gpio_request_array(omap3_evm_ehci_gpios,
ARRAY_SIZE(omap3_evm_ehci_gpios));
/* setup EHCI phy reset config */
omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP);
usbhs_bdata.reset_gpio_port[1] = 21;
/* EVM REV >= E can supply 500mA with EXTVBUS programming */
musb_board_data.power = 500;
musb_board_data.extvbus = 1;
} else {
/* setup EHCI phy reset on MDC */
omap_mux_init_gpio(135, OMAP_PIN_OUTPUT);
usbhs_bdata.reset_gpio_port[1] = 135;
}
usb_musb_init(&musb_board_data);
usbhs_init(&usbhs_bdata);
omap_ads7846_init(1, OMAP3_EVM_TS_GPIO, 310, NULL);
omap3evm_init_smsc911x();
omap3_evm_display_init();
#ifdef CONFIG_WL12XX_PLATFORM_DATA
/* WL12xx WLAN Init */
if (wl12xx_set_platform_data(&omap3evm_wlan_data))
pr_err("error setting wl12xx data\n");
platform_device_register(&omap3evm_wlan_regulator);
#endif
}
static void __init omap3_evm_init(void)
{
omap3_evm_get_revision();
if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2)
omap3evm_twldata.vaux2 = &omap3evm_vaux2;
else
omap3evm_twldata.vusb = &omap3_evm_vusb;
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap3_evm_i2c_init();
platform_add_devices(omap3_evm_devices, ARRAY_SIZE(omap3_evm_devices));
spi_register_board_info(omap3evm_spi_board_info,
ARRAY_SIZE(omap3evm_spi_board_info));
omap_serial_init();
/* OMAP3EVM uses ISP1504 phy and so register nop transceiver */
usb_nop_xceiv_register();
if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) {
/* enable EHCI VBUS using GPIO22 */
omap_mux_init_gpio(22, OMAP_PIN_INPUT_PULLUP);
gpio_request(OMAP3_EVM_EHCI_VBUS, "enable EHCI VBUS");
gpio_direction_output(OMAP3_EVM_EHCI_VBUS, 0);
gpio_set_value(OMAP3_EVM_EHCI_VBUS, 1);
/* Select EHCI port on main board */
omap_mux_init_gpio(61, OMAP_PIN_INPUT_PULLUP);
gpio_request(OMAP3_EVM_EHCI_SELECT, "select EHCI port");
gpio_direction_output(OMAP3_EVM_EHCI_SELECT, 0);
gpio_set_value(OMAP3_EVM_EHCI_SELECT, 0);
/* setup EHCI phy reset config */
omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP);
ehci_pdata.reset_gpio_port[1] = 21;
/* EVM REV >= E can supply 500mA with EXTVBUS programming */
musb_board_data.power = 500;
musb_board_data.extvbus = 1;
} else {
/* setup EHCI phy reset on MDC */
omap_mux_init_gpio(135, OMAP_PIN_OUTPUT);
ehci_pdata.reset_gpio_port[1] = 135;
}
usb_musb_init(&musb_board_data);
usb_ehci_init(&ehci_pdata);
ads7846_dev_init();
omap3evm_init_smsc911x();
omap3_evm_display_init();
}
/*
* Routine: setup_net_chip
* Description: Setting up the configuration GPMC registers specific to the
* Ethernet hardware.
*/
static void setup_net_chip(void)
{
struct gpio *gpio3_base = (struct gpio *)OMAP34XX_GPIO3_BASE;
struct gpio *gpio1_base = (struct gpio *)OMAP34XX_GPIO1_BASE;
struct ctrl *ctrl_base = (struct ctrl *)OMAP34XX_CTRL_BASE;
/* Configure GPMC registers */
writel(NET_GPMC_CONFIG1, &gpmc_cfg->cs[5].config1);
writel(NET_GPMC_CONFIG2, &gpmc_cfg->cs[5].config2);
writel(NET_GPMC_CONFIG3, &gpmc_cfg->cs[5].config3);
writel(NET_GPMC_CONFIG4, &gpmc_cfg->cs[5].config4);
writel(NET_GPMC_CONFIG5, &gpmc_cfg->cs[5].config5);
writel(NET_GPMC_CONFIG6, &gpmc_cfg->cs[5].config6);
writel(NET_GPMC_CONFIG7, &gpmc_cfg->cs[5].config7);
/* Enable off mode for NWE in PADCONF_GPMC_NWE register */
writew(readw(&ctrl_base ->gpmc_nwe) | 0x0E00, &ctrl_base->gpmc_nwe);
/* Enable off mode for NOE in PADCONF_GPMC_NADV_ALE register */
writew(readw(&ctrl_base->gpmc_noe) | 0x0E00, &ctrl_base->gpmc_noe);
/* Enable off mode for ALE in PADCONF_GPMC_NADV_ALE register */
writew(readw(&ctrl_base->gpmc_nadv_ale) | 0x0E00,
&ctrl_base->gpmc_nadv_ale);
/* determine omap3evm revision */
omap3_evm_get_revision();
if ( get_omap3_evm_rev() == OMAP3EVM_BOARD_GEN_1 ){
/* Make GPIO 64 as output pin */
writel(readl(&gpio3_base->oe) & ~(GPIO0), &gpio3_base->oe);
/* Now send a pulse on the GPIO pin */
writel(GPIO0, &gpio3_base->setdataout);
udelay(1);
writel(GPIO0, &gpio3_base->cleardataout);
udelay(1);
writel(GPIO0, &gpio3_base->setdataout);
}else{
/* Make GPIO 07 as output pin */
writel(readl(&gpio1_base->oe) & ~(GPIO7), &gpio1_base->oe);
/* Now send a pulse on the GPIO pin */
writel(GPIO7, &gpio1_base->setdataout);
udelay(1);
writel(GPIO7, &gpio1_base->cleardataout);
udelay(1);
writel(GPIO7, &gpio1_base->setdataout);
}
}
static void __init omap3_evm_init(void)
{
omap3_evm_get_revision();
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap3_evm_i2c_init();
platform_add_devices(omap3_evm_devices, ARRAY_SIZE(omap3_evm_devices));
spi_register_board_info(omap3evm_spi_board_info,
ARRAY_SIZE(omap3evm_spi_board_info));
omap_serial_init();
#ifdef CONFIG_NOP_USB_XCEIV
/* OMAP3EVM uses ISP1504 phy and so register nop transceiver */
usb_nop_xceiv_register();
#endif
if (get_omap3_evm_rev() >= OMAP3EVM_BOARD_GEN_2) {
/* enable EHCI VBUS using GPIO22 */
omap_mux_init_gpio(22, OMAP_PIN_INPUT_PULLUP);
gpio_request(OMAP3_EVM_EHCI_VBUS, "enable EHCI VBUS");
gpio_direction_output(OMAP3_EVM_EHCI_VBUS, 0);
gpio_set_value(OMAP3_EVM_EHCI_VBUS, 1);
/* Select EHCI port on main board */
omap_mux_init_gpio(61, OMAP_PIN_INPUT_PULLUP);
gpio_request(OMAP3_EVM_EHCI_SELECT, "select EHCI port");
gpio_direction_output(OMAP3_EVM_EHCI_SELECT, 0);
gpio_set_value(OMAP3_EVM_EHCI_SELECT, 0);
/* setup EHCI phy reset config */
omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP);
ehci_pdata.reset_gpio_port[1] = 21;
} else {
/* setup EHCI phy reset on MDC */
omap_mux_init_gpio(135, OMAP_PIN_OUTPUT);
ehci_pdata.reset_gpio_port[1] = 135;
/* MDC also need VUSB1V5 regulator */
ehci_pdata.aux[1] = 1;
}
usb_musb_init();
usb_ehci_init(&ehci_pdata);
ads7846_dev_init();
omap3evm_init_smsc911x();
}
/*
* Routine: misc_init_r
* Description: Init ethernet (done here so udelay works)
*/
int misc_init_r(void)
{
#ifdef CONFIG_DRIVER_OMAP34XX_I2C
i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
#endif
#if defined(CONFIG_CMD_NET)
setup_net_chip();
#endif
omap3_evm_get_revision();
#if defined(CONFIG_CMD_NET)
reset_net_chip();
#endif
dieid_num_r();
return 0;
}
/*
* Routine: misc_init_r
* Description: Init ethernet (done here so udelay works)
*/
int misc_init_r(void)
{
#ifdef CONFIG_SYS_I2C_OMAP34XX
i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
#endif
#if defined(CONFIG_CMD_NET)
setup_net_chip();
#endif
omap3_evm_get_revision();
#if defined(CONFIG_CMD_NET)
reset_net_chip();
#endif
omap_die_id_display();
return 0;
}
