int board_late_init(void)
{
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
char *name = "unknown";
if (is_dra72x()) {
if (board_is_dra72x_revc_or_later())
name = "dra72x-revc";
else if (board_is_dra71x_evm())
name = "dra71x";
else
name = "dra72x";
} else {
name = "dra7xx";
}
set_board_info_env(name);
/*
* Default FIT boot on HS devices. Non FIT images are not allowed
* on HS devices.
*/
if (get_device_type() == HS_DEVICE)
env_set("boot_fit", "1");
omap_die_id_serial();
omap_set_fastboot_vars();
#endif
return 0;
}
int board_late_init(void)
{
#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
char *name = "unknown";
if (is_dra72x()) {
if (board_is_dra72x_revc_or_later())
name = "dra72x-revc";
else if (board_is_dra71x_evm())
name = "dra71x";
else
name = "dra72x";
} else if (is_dra76x_abz()) {
name = "dra76x_abz";
} else if (is_dra76x_acd()) {
name = "dra76x_acd";
} else {
name = "dra7xx";
}
set_board_info_env(name);
/*
* Default FIT boot on HS devices. Non FIT images are not allowed
* on HS devices.
*/
if (get_device_type() == HS_DEVICE)
env_set("boot_fit", "1");
omap_die_id_serial();
omap_set_fastboot_vars();
/*
* Hook the LDO1 regulator to EN pin. This applies only to LP8733
* Rest all regulators are hooked to EN Pin at reset.
*/
if (board_is_dra71x_evm())
palmas_i2c_write_u8(LP873X_I2C_SLAVE_ADDR, 0x9, 0x7);
#endif
#if CONFIG_IS_ENABLED(DM_USB) && CONFIG_IS_ENABLED(OF_CONTROL)
if (device_okay("/ocp/omap_dwc3_1@48880000"))
enable_usb_clocks(0);
if (device_okay("/ocp/omap_dwc3_2@488c0000"))
enable_usb_clocks(1);
#endif
return 0;
}
int board_late_init(void)
{
setup_board_eeprom_env();
u8 val;
/*
* DEV_CTRL.DEV_ON = 1 please - else palmas switches off in 8 seconds
* This is the POWERHOLD-in-Low behavior.
*/
palmas_i2c_write_u8(TPS65903X_CHIP_P1, 0xA0, 0x1);
/*
* Default FIT boot on HS devices. Non FIT images are not allowed
* on HS devices.
*/
if (get_device_type() == HS_DEVICE)
env_set("boot_fit", "1");
/*
* Set the GPIO7 Pad to POWERHOLD. This has higher priority
* over DEV_CTRL.DEV_ON bit. This can be reset in case of
* PMIC Power off. So to be on the safer side set it back
* to POWERHOLD mode irrespective of the current state.
*/
palmas_i2c_read_u8(TPS65903X_CHIP_P1, TPS65903X_PRIMARY_SECONDARY_PAD2,
&val);
val = val | TPS65903X_PAD2_POWERHOLD_MASK;
palmas_i2c_write_u8(TPS65903X_CHIP_P1, TPS65903X_PRIMARY_SECONDARY_PAD2,
val);
omap_die_id_serial();
omap_set_fastboot_vars();
am57x_idk_lcd_detect();
#if !defined(CONFIG_SPL_BUILD)
board_ti_set_ethaddr(2);
#endif
return 0;
}
