/*
* Copy an instruction and adjust the displacement if the instruction
* uses the %rip-relative addressing mode.
* If it does, Return the address of the 32-bit displacement word.
* If not, return null.
* Only applicable to 64-bit x86.
*/
int __copy_instruction(u8 *dest, u8 *src)
{
struct insn insn;
kprobe_opcode_t buf[MAX_INSN_SIZE];
int length;
unsigned long recovered_insn =
recover_probed_instruction(buf, (unsigned long)src);
if (!recovered_insn)
return 0;
kernel_insn_init(&insn, (void *)recovered_insn, MAX_INSN_SIZE);
insn_get_length(&insn);
length = insn.length;
/* Another subsystem puts a breakpoint, failed to recover */
if (insn.opcode.bytes[0] == BREAKPOINT_INSTRUCTION)
return 0;
pax_open_kernel();
memcpy(dest, insn.kaddr, length);
pax_close_kernel();
#ifdef CONFIG_X86_64
if (insn_rip_relative(&insn)) {
s64 newdisp;
u8 *disp;
kernel_insn_init(&insn, dest, length);
insn_get_displacement(&insn);
/*
* The copied instruction uses the %rip-relative addressing
* mode. Adjust the displacement for the difference between
* the original location of this instruction and the location
* of the copy that will actually be run. The tricky bit here
* is making sure that the sign extension happens correctly in
* this calculation, since we need a signed 32-bit result to
* be sign-extended to 64 bits when it's added to the %rip
* value and yield the same 64-bit result that the sign-
* extension of the original signed 32-bit displacement would
* have given.
*/
newdisp = (u8 *) src + (s64) insn.displacement.value - (u8 *) dest;
if ((s64) (s32) newdisp != newdisp) {
pr_err("Kprobes error: new displacement does not fit into s32 (%llx)\n", newdisp);
pr_err("\tSrc: %p, Dest: %p, old disp: %x\n", src, dest, insn.displacement.value);
return 0;
}
disp = (u8 *) dest + insn_offset_displacement(&insn);
pax_open_kernel();
*(s32 *) disp = (s32) newdisp;
pax_close_kernel();
}
#endif
return length;
}
void od_unregister_powersave_bias_handler(void)
{
pax_open_kernel();
*(void **)&od_ops.powersave_bias_target = generic_powersave_bias_target;
pax_close_kernel();
od_set_powersave_bias(0);
}
static void jit_fill_hole(void *area, unsigned int size)
{
/* fill whole space with int3 instructions */
pax_open_kernel();
memset(area, 0xcc, size);
pax_close_kernel();
}
void __init exynos_pm_init(void)
{
const struct of_device_id *match;
struct device_node *np;
u32 tmp;
np = of_find_matching_node_and_match(NULL, exynos_pmu_of_device_ids, &match);
if (!np) {
pr_err("Failed to find PMU node\n");
return;
}
if (WARN_ON(!of_find_property(np, "interrupt-controller", NULL))) {
pr_warn("Outdated DT detected, suspend/resume will NOT work\n");
return;
}
pm_data = (const struct exynos_pm_data *) match->data;
/* All wakeup disable */
tmp = pmu_raw_readl(S5P_WAKEUP_MASK);
tmp |= pm_data->wake_disable_mask;
pmu_raw_writel(tmp, S5P_WAKEUP_MASK);
pax_open_kernel();
*(void **)&exynos_pm_syscore_ops.suspend = pm_data->pm_suspend;
*(void **)&exynos_pm_syscore_ops.resume = pm_data->pm_resume;
pax_close_kernel();
register_syscore_ops(&exynos_pm_syscore_ops);
suspend_set_ops(&exynos_suspend_ops);
}
int radeon_mmap(struct file *filp, struct vm_area_struct *vma)
{
struct drm_file *file_priv;
struct radeon_device *rdev;
int r;
if (unlikely(vma->vm_pgoff < DRM_FILE_PAGE_OFFSET)) {
return drm_mmap(filp, vma);
}
file_priv = filp->private_data;
rdev = file_priv->minor->dev->dev_private;
if (rdev == NULL) {
return -EINVAL;
}
r = ttm_bo_mmap(filp, vma, &rdev->mman.bdev);
if (unlikely(r != 0)) {
return r;
}
if (unlikely(ttm_vm_ops == NULL)) {
ttm_vm_ops = vma->vm_ops;
pax_open_kernel();
radeon_ttm_vm_ops = *ttm_vm_ops;
radeon_ttm_vm_ops.fault = &radeon_ttm_fault;
pax_close_kernel();
}
vma->vm_ops = &radeon_ttm_vm_ops;
return 0;
}
int apply_relocate(Elf32_Shdr *sechdrs,
const char *strtab,
unsigned int symindex,
unsigned int relsec,
struct module *me)
{
unsigned int i;
Elf32_Rel *rel = (void *)sechdrs[relsec].sh_addr;
Elf32_Sym *sym;
uint32_t *plocation, location;
DEBUGP("Applying relocate section %u to %u\n", relsec,
sechdrs[relsec].sh_info);
for (i = 0; i < sechdrs[relsec].sh_size / sizeof(*rel); i++) {
/* This is where to make the change */
plocation = (void *)sechdrs[sechdrs[relsec].sh_info].sh_addr + rel[i].r_offset;
location = (uint32_t)plocation;
if (sechdrs[sechdrs[relsec].sh_info].sh_flags & SHF_EXECINSTR)
plocation = ktla_ktva((void *)plocation);
/* This is the symbol it is referring to. Note that all
undefined symbols have been resolved. */
sym = (Elf32_Sym *)sechdrs[symindex].sh_addr
+ ELF32_R_SYM(rel[i].r_info);
switch (ELF32_R_TYPE(rel[i].r_info)) {
case R_386_32:
/* We add the value into the location given */
pax_open_kernel();
*plocation += sym->st_value;
pax_close_kernel();
break;
case R_386_PC32:
/* Add the value, subtract its postition */
pax_open_kernel();
*plocation += sym->st_value - location;
pax_close_kernel();
break;
default:
printk(KERN_ERR "module %s: Unknown relocation: %u\n",
me->name, ELF32_R_TYPE(rel[i].r_info));
return -ENOEXEC;
}
}
return 0;
}
void od_register_powersave_bias_handler(unsigned int (*f)
(struct cpufreq_policy *, unsigned int, unsigned int),
unsigned int powersave_bias)
{
pax_open_kernel();
*(void **)&od_ops.powersave_bias_target = f;
pax_close_kernel();
od_set_powersave_bias(powersave_bias);
}
static void jit_fill_hole(void *area, unsigned int size)
{
u32 *ptr;
/* We are guaranteed to have aligned memory. */
pax_open_kernel();
for (ptr = area; size >= sizeof(u32); size -= sizeof(u32))
*ptr++ = __opcode_to_mem_arm(ARM_INST_UDF);
pax_close_kernel();
}
static int __init load_scm_model_init(struct platform_device *sdev)
{
u8 data;
int result;
if (!quirks->ec_read_only) {
/* allow userland write sysfs file */
pax_open_kernel();
*(void **)&dev_attr_bluetooth.store = store_bluetooth;
*(void **)&dev_attr_wlan.store = store_wlan;
*(void **)&dev_attr_threeg.store = store_threeg;
*(umode_t *)&dev_attr_bluetooth.attr.mode |= S_IWUSR;
*(umode_t *)&dev_attr_wlan.attr.mode |= S_IWUSR;
*(umode_t *)&dev_attr_threeg.attr.mode |= S_IWUSR;
pax_close_kernel();
}
/* disable hardware control by fn key */
result = ec_read(MSI_STANDARD_EC_SCM_LOAD_ADDRESS, &data);
if (result < 0)
return result;
result = ec_write(MSI_STANDARD_EC_SCM_LOAD_ADDRESS,
data | MSI_STANDARD_EC_SCM_LOAD_MASK);
if (result < 0)
return result;
/* initial rfkill */
result = rfkill_init(sdev);
if (result < 0)
goto fail_rfkill;
/* setup input device */
result = msi_laptop_input_setup();
if (result)
goto fail_input;
result = i8042_install_filter(msi_laptop_i8042_filter);
if (result) {
pr_err("Unable to install key filter\n");
goto fail_filter;
}
return 0;
fail_filter:
msi_laptop_input_destroy();
fail_input:
rfkill_cleanup();
fail_rfkill:
return result;
}
static int __init abyss_init (void)
{
pax_open_kernel();
memcpy((void *)&abyss_netdev_ops, &tms380tr_netdev_ops, sizeof(tms380tr_netdev_ops));
*(void **)&abyss_netdev_ops.ndo_open = abyss_open;
*(void **)&abyss_netdev_ops.ndo_stop = abyss_close;
pax_close_kernel();
return pci_register_driver(&abyss_driver);
}
static void swap_ex(void *a, void *b, int size)
{
struct exception_table_entry t, *x = a, *y = b;
t = *x;
pax_open_kernel();
*x = *y;
*y = t;
pax_close_kernel();
}
static int notifier_chain_register(struct notifier_block **nl,
struct notifier_block *n)
{
while ((*nl) != NULL) {
if (n->priority > (*nl)->priority)
break;
nl = (struct notifier_block **)&((*nl)->next);
}
pax_open_kernel();
*(const void **)&n->next = *nl;
rcu_assign_pointer(*nl, n);
pax_close_kernel();
return 0;
}
static int __init init_nls_euc_jp(void)
{
p_nls = load_nls("cp932");
if (p_nls) {
pax_open_kernel();
*(const unsigned char **)&table.charset2upper = p_nls->charset2upper;
*(const unsigned char **)&table.charset2lower = p_nls->charset2lower;
pax_close_kernel();
return register_nls(&table);
}
return -EINVAL;
}
static int notifier_chain_unregister(struct notifier_block **nl,
struct notifier_block *n)
{
while ((*nl) != NULL) {
if ((*nl) == n) {
pax_open_kernel();
rcu_assign_pointer(*nl, n->next);
pax_close_kernel();
return 0;
}
nl = (struct notifier_block **)&((*nl)->next);
}
return -ENOENT;
}
static nokprobe_inline void
__synthesize_relative_insn(void *from, void *to, u8 op)
{
struct __arch_relative_insn {
u8 op;
s32 raddr;
} __packed *insn;
insn = (struct __arch_relative_insn *)ktla_ktva(from);
pax_open_kernel();
insn->raddr = (s32)((long)(to) - ((long)(from) + 5));
insn->op = op;
pax_close_kernel();
}
static __init struct clk *__socfpga_pll_init(struct device_node *node,
const struct clk_ops *ops)
{
u32 reg;
struct clk *clk;
struct socfpga_pll *pll_clk;
const char *clk_name = node->name;
const char *parent_name[SOCFPGA_MAX_PARENTS];
struct clk_init_data init;
struct device_node *clkmgr_np;
int rc;
of_property_read_u32(node, "reg", ®);
pll_clk = kzalloc(sizeof(*pll_clk), GFP_KERNEL);
if (WARN_ON(!pll_clk))
return NULL;
clkmgr_np = of_find_compatible_node(NULL, NULL, "altr,clk-mgr");
clk_mgr_base_addr = of_iomap(clkmgr_np, 0);
BUG_ON(!clk_mgr_base_addr);
pll_clk->hw.reg = clk_mgr_base_addr + reg;
of_property_read_string(node, "clock-output-names", &clk_name);
init.name = clk_name;
init.ops = ops;
init.flags = 0;
init.num_parents = of_clk_parent_fill(node, parent_name, SOCFPGA_MAX_PARENTS);
init.parent_names = parent_name;
pll_clk->hw.hw.init = &init;
pll_clk->hw.bit_idx = SOCFPGA_PLL_EXT_ENA;
pax_open_kernel();
*(void **)&clk_pll_ops.enable = clk_gate_ops.enable;
*(void **)&clk_pll_ops.disable = clk_gate_ops.disable;
pax_close_kernel();
clk = clk_register(NULL, &pll_clk->hw.hw);
if (WARN_ON(IS_ERR(clk))) {
kfree(pll_clk);
return NULL;
}
rc = of_clk_add_provider(node, of_clk_src_simple_get, clk);
return clk;
}
/**
* register_security - registers a security framework with the kernel
* @ops: a pointer to the struct security_options that is to be registered
*
* This function allows a security module to register itself with the
* kernel security subsystem. Some rudimentary checking is done on the @ops
* value passed to this function. You'll need to check first if your LSM
* is allowed to register its @ops by calling security_module_enable(@ops).
*
* If there is already a security module registered with the kernel,
* an error will be returned. Otherwise %0 is returned on success.
*/
int __init register_security(struct security_operations *ops)
{
if (verify(ops)) {
printk(KERN_DEBUG "%s could not verify "
"security_operations structure.\n", __func__);
return -EINVAL;
}
if (security_ops != &default_security_ops)
return -EAGAIN;
pax_open_kernel();
security_ops = ops;
pax_close_kernel();
return 0;
}
int omapdss_register_display(struct omap_dss_device *dssdev)
{
struct omap_dss_driver *drv = dssdev->driver;
int id;
/*
* Note: this presumes all the displays are either using DT or non-DT,
* which normally should be the case. This also presumes that all
* displays either have an DT alias, or none has.
*/
if (dssdev->dev->of_node) {
id = of_alias_get_id(dssdev->dev->of_node, "display");
if (id < 0)
id = disp_num_counter++;
} else {
id = disp_num_counter++;
}
snprintf(dssdev->alias, sizeof(dssdev->alias), "display%d", id);
/* Use 'label' property for name, if it exists */
if (dssdev->dev->of_node)
of_property_read_string(dssdev->dev->of_node, "label",
&dssdev->name);
if (dssdev->name == NULL)
dssdev->name = dssdev->alias;
pax_open_kernel();
if (drv && drv->get_resolution == NULL)
*(void **)&drv->get_resolution = omapdss_default_get_resolution;
if (drv && drv->get_recommended_bpp == NULL)
*(void **)&drv->get_recommended_bpp = omapdss_default_get_recommended_bpp;
if (drv && drv->get_timings == NULL)
*(void **)&drv->get_timings = omapdss_default_get_timings;
pax_close_kernel();
mutex_lock(&panel_list_mutex);
list_add_tail(&dssdev->panel_list, &panel_list);
mutex_unlock(&panel_list_mutex);
return 0;
}
static int __init setup_pax_nouderef(char *str)
{
unsigned int cpu;
#ifdef CONFIG_PAX_KERNEXEC
unsigned long cr0;
pax_open_kernel(cr0);
#endif
for (cpu = 0; cpu < NR_CPUS; cpu++)
get_cpu_gdt_table(cpu)[GDT_ENTRY_KERNEL_DS].b = 0x00cf9300;
#ifdef CONFIG_PAX_KERNEXEC
pax_close_kernel(cr0);
#endif
return 1;
}
/*
* kmap_atomic/kunmap_atomic is significantly faster than kmap/kunmap because
* no global lock is needed and because the kmap code must perform a global TLB
* invalidation when the kmap pool wraps.
*
* However when holding an atomic kmap it is not legal to sleep, so atomic
* kmaps are appropriate for short, tight code paths only.
*/
void *kmap_atomic_prot(struct page *page, pgprot_t prot)
{
unsigned long vaddr;
int idx, type;
/* even !CONFIG_PREEMPT needs this, for in_atomic in do_page_fault */
pagefault_disable();
if (!PageHighMem(page))
return page_address(page);
type = kmap_atomic_idx_push();
idx = type + KM_TYPE_NR*smp_processor_id();
vaddr = __fix_to_virt(FIX_KMAP_BEGIN + idx);
BUG_ON(!pte_none(*(kmap_pte-idx)));
pax_open_kernel();
set_pte(kmap_pte-idx, mk_pte(page, prot));
pax_close_kernel();
return (void *)vaddr;
}
void __init pnpbios_calls_init(union pnp_bios_install_struct *header)
{
int i;
spin_lock_init(&pnp_bios_lock);
pnp_bios_callpoint.offset = header->fields.pm16offset;
pnp_bios_callpoint.segment = PNP_CS16;
pax_open_kernel();
for_each_possible_cpu(i) {
struct desc_struct *gdt = get_cpu_gdt_table(i);
if (!gdt)
continue;
set_desc_base(&gdt[GDT_ENTRY_PNPBIOS_CS32],
(unsigned long)&pnp_bios_callfunc);
set_desc_base(&gdt[GDT_ENTRY_PNPBIOS_CS16],
(unsigned long)__va(header->fields.pm16cseg));
set_desc_base(&gdt[GDT_ENTRY_PNPBIOS_DS],
(unsigned long)__va(header->fields.pm16dseg));
}
pax_close_kernel();
}
static void __init acpi_cpufreq_boost_init(void)
{
if (boot_cpu_has(X86_FEATURE_CPB) || boot_cpu_has(X86_FEATURE_IDA)) {
msrs = msrs_alloc();
if (!msrs)
return;
pax_open_kernel();
*(bool *)&acpi_cpufreq_driver.boost_supported = true;
*(bool *)&acpi_cpufreq_driver.boost_enabled = boost_state(0);
pax_close_kernel();
cpu_notifier_register_begin();
/* Force all MSRs to the same value */
boost_set_msrs(acpi_cpufreq_driver.boost_enabled,
cpu_online_mask);
__register_cpu_notifier(&boost_nb);
cpu_notifier_register_done();
}
}
static int max8973_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct max8973_regulator_platform_data *pdata;
struct regulator_config config = { };
struct regulator_dev *rdev;
struct max8973_chip *max;
int ret;
pdata = client->dev.platform_data;
if (!pdata) {
dev_err(&client->dev, "No Platform data");
return -EIO;
}
max = devm_kzalloc(&client->dev, sizeof(*max), GFP_KERNEL);
if (!max) {
dev_err(&client->dev, "Memory allocation for max failed\n");
return -ENOMEM;
}
max->regmap = devm_regmap_init_i2c(client, &max8973_regmap_config);
if (IS_ERR(max->regmap)) {
ret = PTR_ERR(max->regmap);
dev_err(&client->dev, "regmap init failed, err %d\n", ret);
return ret;
}
i2c_set_clientdata(client, max);
max->dev = &client->dev;
max->desc.name = id->name;
max->desc.id = 0;
max->desc.ops = &max8973_dcdc_ops;
max->desc.type = REGULATOR_VOLTAGE;
max->desc.owner = THIS_MODULE;
max->desc.min_uV = MAX8973_MIN_VOLATGE;
max->desc.uV_step = MAX8973_VOLATGE_STEP;
max->desc.n_voltages = MAX8973_BUCK_N_VOLTAGE;
if (!pdata->enable_ext_control) {
max->desc.enable_reg = MAX8973_VOUT;
max->desc.enable_mask = MAX8973_VOUT_ENABLE;
pax_open_kernel();
*(void **)&max8973_dcdc_ops.enable = regulator_enable_regmap;
*(void **)&max8973_dcdc_ops.disable = regulator_disable_regmap;
*(void **)&max8973_dcdc_ops.is_enabled = regulator_is_enabled_regmap;
pax_close_kernel();
}
max->enable_external_control = pdata->enable_ext_control;
max->dvs_gpio = pdata->dvs_gpio;
max->curr_gpio_val = pdata->dvs_def_state;
max->curr_vout_reg = MAX8973_VOUT + pdata->dvs_def_state;
max->lru_index[0] = max->curr_vout_reg;
max->valid_dvs_gpio = false;
if (gpio_is_valid(max->dvs_gpio)) {
int gpio_flags;
int i;
gpio_flags = (pdata->dvs_def_state) ?
GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW;
ret = devm_gpio_request_one(&client->dev, max->dvs_gpio,
gpio_flags, "max8973-dvs");
if (ret) {
dev_err(&client->dev,
"gpio_request for gpio %d failed, err = %d\n",
max->dvs_gpio, ret);
return ret;
}
max->valid_dvs_gpio = true;
/*
* Initialize the lru index with vout_reg id
* The index 0 will be most recently used and
* set with the max->curr_vout_reg */
for (i = 0; i < MAX8973_MAX_VOUT_REG; ++i)
max->lru_index[i] = i;
max->lru_index[0] = max->curr_vout_reg;
max->lru_index[max->curr_vout_reg] = 0;
}
ret = max8973_init_dcdc(max, pdata);
if (ret < 0) {
dev_err(max->dev, "Max8973 Init failed, err = %d\n", ret);
return ret;
}
config.dev = &client->dev;
config.init_data = pdata->reg_init_data;
config.driver_data = max;
config.of_node = client->dev.of_node;
config.regmap = max->regmap;
/* Register the regulators */
rdev = regulator_register(&max->desc, &config);
if (IS_ERR(rdev)) {
ret = PTR_ERR(rdev);
dev_err(max->dev, "regulator register failed, err %d\n", ret);
return ret;
}
max->rdev = rdev;
return 0;
}
static int zt5550_hc_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
{
int status;
status = zt5550_hc_config(pdev);
if(status != 0) {
return status;
}
dbg("returned from zt5550_hc_config");
memset(&zt5550_hpc, 0, sizeof (struct cpci_hp_controller));
zt5550_hpc.ops = &zt5550_hpc_ops;
if(!poll) {
zt5550_hpc.irq = hc_dev->irq;
zt5550_hpc.irq_flags = IRQF_SHARED;
zt5550_hpc.dev_id = hc_dev;
pax_open_kernel();
*(void **)&zt5550_hpc_ops.enable_irq = zt5550_hc_enable_irq;
*(void **)&zt5550_hpc_ops.disable_irq = zt5550_hc_disable_irq;
*(void **)&zt5550_hpc_ops.check_irq = zt5550_hc_check_irq;
pax_open_kernel();
} else {
info("using ENUM# polling mode");
}
status = cpci_hp_register_controller(&zt5550_hpc);
if(status != 0) {
err("could not register cPCI hotplug controller");
goto init_hc_error;
}
dbg("registered controller");
/* Look for first device matching cPCI bus's bridge vendor and device IDs */
if(!(bus0_dev = pci_get_device(PCI_VENDOR_ID_DEC,
PCI_DEVICE_ID_DEC_21154, NULL))) {
status = -ENODEV;
goto init_register_error;
}
bus0 = bus0_dev->subordinate;
pci_dev_put(bus0_dev);
status = cpci_hp_register_bus(bus0, 0x0a, 0x0f);
if(status != 0) {
err("could not register cPCI hotplug bus");
goto init_register_error;
}
dbg("registered bus");
status = cpci_hp_start();
if(status != 0) {
err("could not started cPCI hotplug system");
cpci_hp_unregister_bus(bus0);
goto init_register_error;
}
dbg("started cpci hp system");
return 0;
init_register_error:
cpci_hp_unregister_controller(&zt5550_hpc);
init_hc_error:
err("status = %d", status);
zt5550_hc_cleanup();
return status;
}
static int sdhci_s3c_probe(struct platform_device *pdev)
{
struct s3c_sdhci_platdata *pdata;
struct sdhci_s3c_drv_data *drv_data;
struct device *dev = &pdev->dev;
struct sdhci_host *host;
struct sdhci_s3c *sc;
struct resource *res;
int ret, irq, ptr, clks;
if (!pdev->dev.platform_data && !pdev->dev.of_node) {
dev_err(dev, "no device data specified\n");
return -ENOENT;
}
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
dev_err(dev, "no irq specified\n");
return irq;
}
host = sdhci_alloc_host(dev, sizeof(struct sdhci_s3c));
if (IS_ERR(host)) {
dev_err(dev, "sdhci_alloc_host() failed\n");
return PTR_ERR(host);
}
sc = sdhci_priv(host);
pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
if (!pdata) {
ret = -ENOMEM;
goto err_pdata_io_clk;
}
if (pdev->dev.of_node) {
ret = sdhci_s3c_parse_dt(&pdev->dev, host, pdata);
if (ret)
goto err_pdata_io_clk;
} else {
memcpy(pdata, pdev->dev.platform_data, sizeof(*pdata));
sc->ext_cd_gpio = -1; /* invalid gpio number */
}
drv_data = sdhci_s3c_get_driver_data(pdev);
sc->host = host;
sc->pdev = pdev;
sc->pdata = pdata;
platform_set_drvdata(pdev, host);
sc->clk_io = devm_clk_get(dev, "hsmmc");
if (IS_ERR(sc->clk_io)) {
dev_err(dev, "failed to get io clock\n");
ret = PTR_ERR(sc->clk_io);
goto err_pdata_io_clk;
}
/* enable the local io clock and keep it running for the moment. */
clk_prepare_enable(sc->clk_io);
for (clks = 0, ptr = 0; ptr < MAX_BUS_CLK; ptr++) {
struct clk *clk;
char name[14];
snprintf(name, 14, "mmc_busclk.%d", ptr);
clk = devm_clk_get(dev, name);
if (IS_ERR(clk))
continue;
clks++;
sc->clk_bus[ptr] = clk;
/*
* save current clock index to know which clock bus
* is used later in overriding functions.
*/
sc->cur_clk = ptr;
dev_info(dev, "clock source %d: %s (%ld Hz)\n",
ptr, name, clk_get_rate(clk));
}
if (clks == 0) {
dev_err(dev, "failed to find any bus clocks\n");
ret = -ENOENT;
goto err_no_busclks;
}
#ifndef CONFIG_PM_RUNTIME
clk_prepare_enable(sc->clk_bus[sc->cur_clk]);
#endif
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
host->ioaddr = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(host->ioaddr)) {
ret = PTR_ERR(host->ioaddr);
goto err_req_regs;
}
/* Ensure we have minimal gpio selected CMD/CLK/Detect */
if (pdata->cfg_gpio)
pdata->cfg_gpio(pdev, pdata->max_width);
host->hw_name = "samsung-hsmmc";
host->ops = &sdhci_s3c_ops;
host->quirks = 0;
host->irq = irq;
/* Setup quirks for the controller */
host->quirks |= SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC;
host->quirks |= SDHCI_QUIRK_NO_HISPD_BIT;
if (drv_data)
host->quirks |= drv_data->sdhci_quirks;
#ifndef CONFIG_MMC_SDHCI_S3C_DMA
/* we currently see overruns on errors, so disable the SDMA
* support as well. */
host->quirks |= SDHCI_QUIRK_BROKEN_DMA;
#endif /* CONFIG_MMC_SDHCI_S3C_DMA */
/* It seems we do not get an DATA transfer complete on non-busy
* transfers, not sure if this is a problem with this specific
* SDHCI block, or a missing configuration that needs to be set. */
host->quirks |= SDHCI_QUIRK_NO_BUSY_IRQ;
/* This host supports the Auto CMD12 */
host->quirks |= SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12;
/* Samsung SoCs need BROKEN_ADMA_ZEROLEN_DESC */
host->quirks |= SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC;
if (pdata->cd_type == S3C_SDHCI_CD_NONE ||
pdata->cd_type == S3C_SDHCI_CD_PERMANENT)
host->quirks |= SDHCI_QUIRK_BROKEN_CARD_DETECTION;
if (pdata->cd_type == S3C_SDHCI_CD_PERMANENT)
host->mmc->caps = MMC_CAP_NONREMOVABLE;
switch (pdata->max_width) {
case 8:
host->mmc->caps |= MMC_CAP_8_BIT_DATA;
case 4:
host->mmc->caps |= MMC_CAP_4_BIT_DATA;
break;
}
if (pdata->pm_caps)
host->mmc->pm_caps |= pdata->pm_caps;
host->quirks |= (SDHCI_QUIRK_32BIT_DMA_ADDR |
SDHCI_QUIRK_32BIT_DMA_SIZE);
/* HSMMC on Samsung SoCs uses SDCLK as timeout clock */
host->quirks |= SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK;
/*
* If controller does not have internal clock divider,
* we can use overriding functions instead of default.
*/
if (host->quirks & SDHCI_QUIRK_NONSTANDARD_CLOCK) {
pax_open_kernel();
*(void **)&sdhci_s3c_ops.set_clock = sdhci_cmu_set_clock;
*(void **)&sdhci_s3c_ops.get_min_clock = sdhci_cmu_get_min_clock;
*(void **)&sdhci_s3c_ops.get_max_clock = sdhci_cmu_get_max_clock;
pax_close_kernel();
}
/* It supports additional host capabilities if needed */
if (pdata->host_caps)
host->mmc->caps |= pdata->host_caps;
if (pdata->host_caps2)
host->mmc->caps2 |= pdata->host_caps2;
pm_runtime_enable(&pdev->dev);
pm_runtime_set_autosuspend_delay(&pdev->dev, 50);
pm_runtime_use_autosuspend(&pdev->dev);
pm_suspend_ignore_children(&pdev->dev, 1);
ret = sdhci_add_host(host);
if (ret) {
dev_err(dev, "sdhci_add_host() failed\n");
pm_runtime_forbid(&pdev->dev);
pm_runtime_get_noresume(&pdev->dev);
goto err_req_regs;
}
/* The following two methods of card detection might call
sdhci_s3c_notify_change() immediately, so they can be called
only after sdhci_add_host(). Setup errors are ignored. */
if (pdata->cd_type == S3C_SDHCI_CD_EXTERNAL && pdata->ext_cd_init)
pdata->ext_cd_init(&sdhci_s3c_notify_change);
if (pdata->cd_type == S3C_SDHCI_CD_GPIO &&
gpio_is_valid(pdata->ext_cd_gpio))
sdhci_s3c_setup_card_detect_gpio(sc);
#ifdef CONFIG_PM_RUNTIME
if (pdata->cd_type != S3C_SDHCI_CD_INTERNAL)
clk_disable_unprepare(sc->clk_io);
#endif
return 0;
err_req_regs:
#ifndef CONFIG_PM_RUNTIME
clk_disable_unprepare(sc->clk_bus[sc->cur_clk]);
#endif
err_no_busclks:
clk_disable_unprepare(sc->clk_io);
err_pdata_io_clk:
sdhci_free_host(host);
return ret;
}
void reset_security_ops(void)
{
pax_open_kernel();
security_ops = &default_security_ops;
pax_close_kernel();
}
int __init op_nmi_init(struct oprofile_operations *ops)
{
__u8 vendor = boot_cpu_data.x86_vendor;
__u8 family = boot_cpu_data.x86;
char *cpu_type = NULL;
int ret = 0;
if (!cpu_has_apic)
return -ENODEV;
if (force_cpu_type == timer)
return -ENODEV;
switch (vendor) {
case X86_VENDOR_AMD:
/* Needs to be at least an Athlon (or hammer in 32bit mode) */
switch (family) {
case 6:
cpu_type = "i386/athlon";
break;
case 0xf:
/*
* Actually it could be i386/hammer too, but
* give user space an consistent name.
*/
cpu_type = "x86-64/hammer";
break;
case 0x10:
cpu_type = "x86-64/family10";
break;
case 0x11:
cpu_type = "x86-64/family11h";
break;
case 0x12:
cpu_type = "x86-64/family12h";
break;
case 0x14:
cpu_type = "x86-64/family14h";
break;
case 0x15:
cpu_type = "x86-64/family15h";
break;
default:
return -ENODEV;
}
model = &op_amd_spec;
break;
case X86_VENDOR_INTEL:
switch (family) {
/* Pentium IV */
case 0xf:
p4_init(&cpu_type);
break;
/* A P6-class processor */
case 6:
ppro_init(&cpu_type);
break;
default:
break;
}
if (cpu_type)
break;
if (!cpu_has_arch_perfmon)
return -ENODEV;
/* use arch perfmon as fallback */
cpu_type = "i386/arch_perfmon";
model = &op_arch_perfmon_spec;
break;
default:
return -ENODEV;
}
/* default values, can be overwritten by model */
ops->create_files = nmi_create_files;
ops->setup = nmi_setup;
ops->shutdown = nmi_shutdown;
ops->start = nmi_start;
ops->stop = nmi_stop;
ops->cpu_type = cpu_type;
if (model->init)
ret = model->init(ops);
if (ret)
return ret;
if (!model->num_virt_counters) {
pax_open_kernel();
*(unsigned int *)&model->num_virt_counters = model->num_counters;
pax_close_kernel();
}
mux_init(ops);
init_suspend_resume();
printk(KERN_INFO "oprofile: using NMI interrupt.\n");
return 0;
}
static int acpi_cpufreq_cpu_init(struct cpufreq_policy *policy)
{
unsigned int i;
unsigned int valid_states = 0;
unsigned int cpu = policy->cpu;
struct acpi_cpufreq_data *data;
unsigned int result = 0;
struct cpuinfo_x86 *c = &cpu_data(policy->cpu);
struct acpi_processor_performance *perf;
#ifdef CONFIG_SMP
static int blacklisted;
#endif
pr_debug("acpi_cpufreq_cpu_init\n");
#ifdef CONFIG_SMP
if (blacklisted)
return blacklisted;
blacklisted = acpi_cpufreq_blacklist(c);
if (blacklisted)
return blacklisted;
#endif
data = kzalloc(sizeof(*data), GFP_KERNEL);
if (!data)
return -ENOMEM;
if (!zalloc_cpumask_var(&data->freqdomain_cpus, GFP_KERNEL)) {
result = -ENOMEM;
goto err_free;
}
perf = per_cpu_ptr(acpi_perf_data, cpu);
data->acpi_perf_cpu = cpu;
policy->driver_data = data;
if (cpu_has(c, X86_FEATURE_CONSTANT_TSC)) {
pax_open_kernel();
*(u8 *)&acpi_cpufreq_driver.flags |= CPUFREQ_CONST_LOOPS;
pax_close_kernel();
}
result = acpi_processor_register_performance(perf, cpu);
if (result)
goto err_free_mask;
policy->shared_type = perf->shared_type;
/*
* Will let policy->cpus know about dependency only when software
* coordination is required.
*/
if (policy->shared_type == CPUFREQ_SHARED_TYPE_ALL ||
policy->shared_type == CPUFREQ_SHARED_TYPE_ANY) {
cpumask_copy(policy->cpus, perf->shared_cpu_map);
}
cpumask_copy(data->freqdomain_cpus, perf->shared_cpu_map);
#ifdef CONFIG_SMP
dmi_check_system(sw_any_bug_dmi_table);
if (bios_with_sw_any_bug && !policy_is_shared(policy)) {
policy->shared_type = CPUFREQ_SHARED_TYPE_ALL;
cpumask_copy(policy->cpus, topology_core_cpumask(cpu));
}
if (check_amd_hwpstate_cpu(cpu) && !acpi_pstate_strict) {
cpumask_clear(policy->cpus);
cpumask_set_cpu(cpu, policy->cpus);
cpumask_copy(data->freqdomain_cpus,
topology_sibling_cpumask(cpu));
policy->shared_type = CPUFREQ_SHARED_TYPE_HW;
pr_info_once(PFX "overriding BIOS provided _PSD data\n");
}
#endif
/* capability check */
if (perf->state_count <= 1) {
pr_debug("No P-States\n");
result = -ENODEV;
goto err_unreg;
}
if (perf->control_register.space_id != perf->status_register.space_id) {
result = -ENODEV;
goto err_unreg;
}
switch (perf->control_register.space_id) {
case ACPI_ADR_SPACE_SYSTEM_IO:
if (boot_cpu_data.x86_vendor == X86_VENDOR_AMD &&
boot_cpu_data.x86 == 0xf) {
pr_debug("AMD K8 systems must use native drivers.\n");
result = -ENODEV;
goto err_unreg;
}
pr_debug("SYSTEM IO addr space\n");
data->cpu_feature = SYSTEM_IO_CAPABLE;
break;
case ACPI_ADR_SPACE_FIXED_HARDWARE:
pr_debug("HARDWARE addr space\n");
if (check_est_cpu(cpu)) {
data->cpu_feature = SYSTEM_INTEL_MSR_CAPABLE;
break;
}
if (check_amd_hwpstate_cpu(cpu)) {
data->cpu_feature = SYSTEM_AMD_MSR_CAPABLE;
break;
}
result = -ENODEV;
goto err_unreg;
default:
pr_debug("Unknown addr space %d\n",
(u32) (perf->control_register.space_id));
result = -ENODEV;
goto err_unreg;
}
data->freq_table = kzalloc(sizeof(*data->freq_table) *
(perf->state_count+1), GFP_KERNEL);
if (!data->freq_table) {
result = -ENOMEM;
goto err_unreg;
}
/* detect transition latency */
policy->cpuinfo.transition_latency = 0;
for (i = 0; i < perf->state_count; i++) {
if ((perf->states[i].transition_latency * 1000) >
policy->cpuinfo.transition_latency)
policy->cpuinfo.transition_latency =
perf->states[i].transition_latency * 1000;
}
/* Check for high latency (>20uS) from buggy BIOSes, like on T42 */
if (perf->control_register.space_id == ACPI_ADR_SPACE_FIXED_HARDWARE &&
policy->cpuinfo.transition_latency > 20 * 1000) {
policy->cpuinfo.transition_latency = 20 * 1000;
printk_once(KERN_INFO
"P-state transition latency capped at 20 uS\n");
}
/* table init */
for (i = 0; i < perf->state_count; i++) {
if (i > 0 && perf->states[i].core_frequency >=
data->freq_table[valid_states-1].frequency / 1000)
continue;
data->freq_table[valid_states].driver_data = i;
data->freq_table[valid_states].frequency =
perf->states[i].core_frequency * 1000;
valid_states++;
}
data->freq_table[valid_states].frequency = CPUFREQ_TABLE_END;
perf->state = 0;
result = cpufreq_table_validate_and_show(policy, data->freq_table);
if (result)
goto err_freqfree;
if (perf->states[0].core_frequency * 1000 != policy->cpuinfo.max_freq)
printk(KERN_WARNING FW_WARN "P-state 0 is not max freq\n");
switch (perf->control_register.space_id) {
case ACPI_ADR_SPACE_SYSTEM_IO:
/*
* The core will not set policy->cur, because
* cpufreq_driver->get is NULL, so we need to set it here.
* However, we have to guess it, because the current speed is
* unknown and not detectable via IO ports.
*/
policy->cur = acpi_cpufreq_guess_freq(data, policy->cpu);
break;
case ACPI_ADR_SPACE_FIXED_HARDWARE:
pax_open_kernel();
*(void **)&acpi_cpufreq_driver.get = get_cur_freq_on_cpu;
pax_close_kernel();
break;
default:
break;
}
/* notify BIOS that we exist */
acpi_processor_notify_smm(THIS_MODULE);
pr_debug("CPU%u - ACPI performance management activated.\n", cpu);
for (i = 0; i < perf->state_count; i++)
pr_debug(" %cP%d: %d MHz, %d mW, %d uS\n",
(i == perf->state ? '*' : ' '), i,
(u32) perf->states[i].core_frequency,
(u32) perf->states[i].power,
(u32) perf->states[i].transition_latency);
/*
* the first call to ->target() should result in us actually
* writing something to the appropriate registers.
*/
data->resume = 1;
return result;
err_freqfree:
kfree(data->freq_table);
err_unreg:
acpi_processor_unregister_performance(cpu);
err_free_mask:
free_cpumask_var(data->freqdomain_cpus);
err_free:
kfree(data);
policy->driver_data = NULL;
return result;
}
static inline u16 call_pnp_bios(u16 func, u16 arg1, u16 arg2, u16 arg3,
u16 arg4, u16 arg5, u16 arg6, u16 arg7,
void *ts1_base, u32 ts1_size,
void *ts2_base, u32 ts2_size)
{
unsigned long flags;
u16 status;
struct desc_struct save_desc_40;
int cpu;
/*
* PnP BIOSes are generally not terribly re-entrant.
* Also, don't rely on them to save everything correctly.
*/
if (pnp_bios_is_utter_crap)
return PNP_FUNCTION_NOT_SUPPORTED;
cpu = get_cpu();
save_desc_40 = get_cpu_gdt_table(cpu)[0x40 / 8];
pax_open_kernel();
get_cpu_gdt_table(cpu)[0x40 / 8] = bad_bios_desc;
pax_close_kernel();
/* On some boxes IRQ's during PnP BIOS calls are deadly. */
spin_lock_irqsave(&pnp_bios_lock, flags);
/* The lock prevents us bouncing CPU here */
if (ts1_size)
Q2_SET_SEL(smp_processor_id(), PNP_TS1, ts1_base, ts1_size);
if (ts2_size)
Q2_SET_SEL(smp_processor_id(), PNP_TS2, ts2_base, ts2_size);
__asm__ __volatile__("pushl %%ebp\n\t"
"pushl %%edi\n\t"
"pushl %%esi\n\t"
"pushl %%ds\n\t"
"pushl %%es\n\t"
"pushl %%fs\n\t"
"pushl %%gs\n\t"
"pushfl\n\t"
"movl %%esp, pnp_bios_fault_esp\n\t"
"movl $1f, pnp_bios_fault_eip\n\t"
"lcall %5,%6\n\t"
"1:popfl\n\t"
"popl %%gs\n\t"
"popl %%fs\n\t"
"popl %%es\n\t"
"popl %%ds\n\t"
"popl %%esi\n\t"
"popl %%edi\n\t"
"popl %%ebp\n\t":"=a"(status)
:"0"((func) | (((u32) arg1) << 16)),
"b"((arg2) | (((u32) arg3) << 16)),
"c"((arg4) | (((u32) arg5) << 16)),
"d"((arg6) | (((u32) arg7) << 16)),
"i"(PNP_CS32), "i"(0)
:"memory");
spin_unlock_irqrestore(&pnp_bios_lock, flags);
pax_open_kernel();
get_cpu_gdt_table(cpu)[0x40 / 8] = save_desc_40;
pax_close_kernel();
put_cpu();
/* If we get here and this is set then the PnP BIOS faulted on us. */
if (pnp_bios_is_utter_crap) {
printk(KERN_ERR
"PnPBIOS: Warning! Your PnP BIOS caused a fatal error. Attempting to continue\n");
printk(KERN_ERR
"PnPBIOS: You may need to reboot with the \"pnpbios=off\" option to operate stably\n");
printk(KERN_ERR
"PnPBIOS: Check with your vendor for an updated BIOS\n");
}
return status;
}
int apply_relocate_add(Elf64_Shdr *sechdrs,
const char *strtab,
unsigned int symindex,
unsigned int relsec,
struct module *me)
{
unsigned int i;
Elf64_Rela *rel = (void *)sechdrs[relsec].sh_addr;
Elf64_Sym *sym;
void *loc;
u64 val;
#ifdef CONFIG_PAX_KERNEXEC
unsigned long cr0;
#endif
DEBUGP("Applying relocate section %u to %u\n", relsec,
sechdrs[relsec].sh_info);
for (i = 0; i < sechdrs[relsec].sh_size / sizeof(*rel); i++) {
/* This is where to make the change */
loc = (void *)sechdrs[sechdrs[relsec].sh_info].sh_addr
+ rel[i].r_offset;
/* This is the symbol it is referring to. Note that all
undefined symbols have been resolved. */
sym = (Elf64_Sym *)sechdrs[symindex].sh_addr
+ ELF64_R_SYM(rel[i].r_info);
DEBUGP("type %d st_value %Lx r_addend %Lx loc %Lx\n",
(int)ELF64_R_TYPE(rel[i].r_info),
sym->st_value, rel[i].r_addend, (u64)loc);
val = sym->st_value + rel[i].r_addend;
switch (ELF64_R_TYPE(rel[i].r_info)) {
case R_X86_64_NONE:
break;
case R_X86_64_64:
#ifdef CONFIG_PAX_KERNEXEC
pax_open_kernel(cr0);
#endif
*(u64 *)loc = val;
#ifdef CONFIG_PAX_KERNEXEC
pax_close_kernel(cr0);
#endif
break;
case R_X86_64_32:
#ifdef CONFIG_PAX_KERNEXEC
pax_open_kernel(cr0);
#endif
*(u32 *)loc = val;
#ifdef CONFIG_PAX_KERNEXEC
pax_close_kernel(cr0);
#endif
if (val != *(u32 *)loc)
goto overflow;
break;
case R_X86_64_32S:
#ifdef CONFIG_PAX_KERNEXEC
pax_open_kernel(cr0);
#endif
*(s32 *)loc = val;
#ifdef CONFIG_PAX_KERNEXEC
pax_close_kernel(cr0);
#endif
if ((s64)val != *(s32 *)loc)
goto overflow;
break;
case R_X86_64_PC32:
val -= (u64)loc;
#ifdef CONFIG_PAX_KERNEXEC
pax_open_kernel(cr0);
#endif
*(u32 *)loc = val;
#ifdef CONFIG_PAX_KERNEXEC
pax_close_kernel(cr0);
#endif
#if 0
if ((s64)val != *(s32 *)loc)
goto overflow;
#endif
break;
default:
printk(KERN_ERR "module %s: Unknown rela relocation: %llu\n",
me->name, ELF64_R_TYPE(rel[i].r_info));
return -ENOEXEC;
}
}
return 0;
overflow:
printk(KERN_ERR "overflow in relocation type %d val %Lx\n",
(int)ELF64_R_TYPE(rel[i].r_info), val);
printk(KERN_ERR "`%s' likely not compiled with -mcmodel=kernel\n",
me->name);
return -ENOEXEC;
}