void main(unsigned long bist)
{
int s3resume = 0;
if (bist == 0)
enable_lapic();
/* Force PCIRST# */
pci_write_config16(PCI_DEV(0, 0x1e, 0), BCTRL, SBR);
udelay(200 * 1000);
pci_write_config16(PCI_DEV(0, 0x1e, 0), BCTRL, 0);
ich7_enable_lpc();
early_superio_config();
/* Set up the console */
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
if (MCHBAR16(SSKPD) == 0xCAFE) {
printk(BIOS_DEBUG, "soft reset detected, rebooting properly\n");
outb(0x6, 0xcf9);
halt();
}
/* Perform some early chipset initialization required
* before RAM initialization can work
*/
i945_early_initialization();
/* This has to happen after i945_early_initialization() */
init_artec_dongle();
s3resume = southbridge_detect_s3_resume();
/* Enable SPD ROMs and DDR-II DRAM */
enable_smbus();
#if CONFIG_DEFAULT_CONSOLE_LOGLEVEL > 8
dump_spd_registers();
#endif
sdram_initialize(s3resume ? 2 : 0, NULL);
/* Perform some initialization that must run before stage2 */
early_ich7_init();
/* This should probably go away. Until now it is required
* and mainboard specific
*/
rcba_config();
/* Chipset Errata! */
fixup_i945_errata();
/* Initialize the internal PCIe links before we go into stage2 */
i945_late_initialization(s3resume);
}
void perform_raminit(int s3resume)
{
int cbmem_was_initted;
struct pei_data pei_data;
/* Prepare USB controller early in S3 resume */
if (!mainboard_should_reset_usb(s3resume))
enable_usb_bar();
mainboard_fill_pei_data(&pei_data);
post_code(0x3a);
pei_data.boot_mode = s3resume ? 2 : 0;
timestamp_add_now(TS_BEFORE_INITRAM);
sdram_initialize(&pei_data);
cbmem_was_initted = !cbmem_recovery(s3resume);
if (!s3resume)
save_mrc_data(&pei_data);
if (s3resume && !cbmem_was_initted) {
/* Failed S3 resume, reset to come up cleanly */
outb(0x6, 0xcf9);
halt();
}
}
void mainboard_romstage_entry(unsigned long bist)
{
const u8 spd_addrmap[4] = { 0x50, 0x51, 0, 0 };
if (bist == 0)
enable_lapic();
/* Disable watchdog timer */
RCBA32(0x3410) = RCBA32(0x3410) | 0x20;
/* Set southbridge and Super I/O GPIOs. */
mb_gpio_init();
nm10_enable_lpc();
winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
report_bist_failure(bist);
enable_smbus();
pineview_early_initialization();
post_code(0x30);
printk(BIOS_DEBUG, "Initializing memory\n");
sdram_initialize(0, spd_addrmap);
printk(BIOS_DEBUG, "Memory initialized\n");
post_code(0x31);
ram_check(0x200000,0x300000);
rcba_config();
}
void main(unsigned long bist)
{
if (bist == 0) {
if (memory_initialized())
hard_reset();
}
/* Set southbridge and superio gpios */
mb_gpio_init();
smscsuperio_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
/* Halt if there was a built in self test failure. */
report_bist_failure(bist);
/* disable TCO timers */
i82801dx_halt_tco_timer();
/* Setup mainboard specific registers */
mb_early_setup();
/* Initialize memory */
sdram_initialize();
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr [] = {
DIMM0, DIMM2, 0, 0,
DIMM1, DIMM3, 0, 0,
#if CONFIG_MAX_PHYSICAL_CPUS > 1
DIMM4, DIMM6, 0, 0,
DIMM5, DIMM7, 0, 0,
#endif
};
int needs_reset;
unsigned bsp_apicid = 0, nodes;
struct mem_controller ctrl[8];
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx);
pc87360_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
setup_default_resource_map();
needs_reset = setup_coherent_ht_domain();
#if CONFIG_LOGICAL_CPUS
// It is said that we should start core1 after all core0 launched
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
/* This is needed to be able to call udelay(). It could be moved to
* memreset_setup, since udelay is called in memreset. */
init_timer();
// automatically set that for you, but you might meet tight space
needs_reset |= ht_setup_chains_x();
if (needs_reset) {
print_info("ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
nodes = get_nodes();
fill_mem_ctrl(nodes, ctrl, spd_addr);
enable_smbus();
memreset_setup();
sdram_initialize(nodes, ctrl);
post_cache_as_ram();
}
void main(unsigned long bist)
{
int s3resume = 0, boot_mode = 0;
if (bist == 0)
enable_lapic();
ich7_enable_lpc();
/* Enable SuperIO PM */
lpc47m15x_enable_serial(PME_DEV, 0x680);
lpc47m15x_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE); /* 0x3f8 */
/* Set up the console */
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
if (MCHBAR16(SSKPD) == 0xCAFE) {
printk(BIOS_DEBUG, "soft reset detected.\n");
boot_mode = 1;
}
/* Perform some early chipset initialization required
* before RAM initialization can work
*/
i945_early_initialization();
s3resume = southbridge_detect_s3_resume();
/* Enable SPD ROMs and DDR-II DRAM */
enable_smbus();
#if CONFIG_DEFAULT_CONSOLE_LOGLEVEL > 8
dump_spd_registers();
#endif
sdram_initialize(s3resume ? 2 : boot_mode, NULL);
/* Perform some initialization that must run before stage2 */
early_ich7_init();
/* This should probably go away. Until now it is required
* and mainboard specific
*/
rcba_config();
/* Chipset Errata! */
fixup_i945_errata();
/* Initialize the internal PCIe links before we go into stage2 */
i945_late_initialization(s3resume);
}
void mainboard_romstage_entry(unsigned long bist)
{
int boot_mode = 0;
if (bist == 0)
enable_lapic();
sch_enable_lpc();
console_init();
/* Halt if there was a built in self test failure */
// report_bist_failure(bist);
// outl (0x00, 0x1088);
/*
* Perform some early chipset initialization required
* before RAM initialization can work.
*/
sch_early_initialization();
sdram_initialize(boot_mode);
sch_shadow_CMC();
poulsbo_setup_Stage1Regs();
poulsbo_setup_Stage2Regs();
#if 0
sch_SMbase_init();
/* Perform some initialization that must run before stage2. */
#endif
/*
* This should probably go away. Until now it is required
* and mainboard specific.
*/
/* Chipset Errata! */
pci_write_config16(PCI_DEV(0, 0x2, 0), GGC, 0x20);
pci_write_config32(PCI_DEV(0, 0x2, 0), 0xc4, 0x00000002);
pci_write_config32(PCI_DEV(0, 0x2, 0), 0xe0, 0x00008000);
pci_write_config32(PCI_DEV(0, 0x2, 0), 0xf0, 0x00000005);
pci_write_config16(PCI_DEV(0, 0x2, 0), 0xf7, 0x80);
pci_write_config16(PCI_DEV(0, 0x2, 0), 0x4, 0x7);
#if RFID_TEST
sch_SMbase_init();
selectcard();
#endif
}
void mainboard_romstage_entry(unsigned long bist)
{
// ch0 ch1
const u8 spd_addrmap[4] = { 0x50, 0, 0x52, 0 };
u8 boot_path = 0;
u8 s3_resume;
timestamp_init(get_initial_timestamp());
timestamp_add_now(TS_START_ROMSTAGE);
/* Set southbridge and Super I/O GPIOs. */
ich7_enable_lpc();
mb_lpc_setup();
console_init();
report_bist_failure(bist);
enable_smbus();
x4x_early_init();
s3_resume = southbridge_detect_s3_resume();
if (s3_resume)
boot_path = BOOT_PATH_RESUME;
if (MCHBAR32(PMSTS_MCHBAR) & PMSTS_WARM_RESET)
boot_path = BOOT_PATH_WARM_RESET;
printk(BIOS_DEBUG, "Initializing memory\n");
timestamp_add_now(TS_BEFORE_INITRAM);
sdram_initialize(boot_path, spd_addrmap);
timestamp_add_now(TS_AFTER_INITRAM);
quick_ram_check();
printk(BIOS_DEBUG, "Memory initialized\n");
x4x_late_init(s3_resume);
printk(BIOS_DEBUG, "x4x late init complete\n");
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr [] = {
// Node 0
(0xa<<3)|0, (0xa<<3)|2, 0, 0,
(0xa<<3)|1, (0xa<<3)|3, 0, 0,
// Node 1
(0xa<<3)|4, (0xa<<3)|6, 0, 0,
(0xa<<3)|5, (0xa<<3)|7, 0, 0,
};
struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE
+ CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
int needs_reset = 0;
unsigned bsp_apicid = 0;
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
sio_setup();
/* Setup the mcp55 */
mcp55_enable_rom();
}
if (bist == 0) {
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
}
w83627hf_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
setup_mb_resource_map();
uart_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
#if CONFIG_USBDEBUG
mcp55_enable_usbdebug(CONFIG_USBDEBUG_DEFAULT_PORT);
early_usbdebug_init();
#endif
console_init();
printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\n");
#if CONFIG_MEM_TRAIN_SEQ == 1
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
#endif
setup_coherent_ht_domain(); // routing table and start other core0
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS==1
// It is said that we should start core1 after all core0 launched
/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
* So here need to make sure last core0 is started, esp for two way system,
* (there may be apic id conflicts in that case)
*/
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
/* it will set up chains and store link pair for optimization later */
ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn
#if SET_FIDVID == 1
{
msr_t msr;
msr=rdmsr(0xc0010042);
print_debug("begin msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
}
enable_fid_change();
enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
init_fidvid_bsp(bsp_apicid);
// show final fid and vid
{
msr_t msr;
msr=rdmsr(0xc0010042);
print_debug("end msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
}
#endif
init_timer(); // Need to use TMICT to synconize FID/VID
needs_reset |= optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
needs_reset |= mcp55_early_setup_x();
// fidvid change will issue one LDTSTOP and the HT change will be effective too
if (needs_reset) {
print_info("ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
//It's the time to set ctrl in sysinfo now;
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
enable_smbus();
/* all ap stopped? */
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
post_cache_as_ram(); // bsp swtich stack to ram and copy sysinfo ram now
}
void main(unsigned long bist)
{
int boot_mode = 0;
int cbmem_was_initted;
struct pei_data pei_data = {
.pei_version = PEI_VERSION,
.mchbar = (uintptr_t)DEFAULT_MCHBAR,
.dmibar = (uintptr_t)DEFAULT_DMIBAR,
.epbar = DEFAULT_EPBAR,
.pciexbar = CONFIG_MMCONF_BASE_ADDRESS,
.smbusbar = SMBUS_IO_BASE,
.wdbbar = 0x4000000,
.wdbsize = 0x1000,
.hpet_address = CONFIG_HPET_ADDRESS,
.rcba = (uintptr_t)DEFAULT_RCBABASE,
.pmbase = DEFAULT_PMBASE,
.gpiobase = DEFAULT_GPIOBASE,
.thermalbase = 0xfed08000,
.system_type = 0, // 0 Mobile, 1 Desktop/Server
.tseg_size = CONFIG_SMM_TSEG_SIZE,
.spd_addresses = { 0xa0, 0x00,0xa4,0x00 },
.ts_addresses = { 0x00, 0x00, 0x00, 0x00 },
.ec_present = 0,
// 0 = leave channel enabled
// 1 = disable dimm 0 on channel
// 2 = disable dimm 1 on channel
// 3 = disable dimm 0+1 on channel
.dimm_channel0_disabled = 2,
.dimm_channel1_disabled = 2,
.max_ddr3_freq = 1333,
.usb_port_config = {
{ 1, 0, 0x0080 }, /* P0: Front port (OC0) */
{ 1, 1, 0x0040 }, /* P1: Back port (OC1) */
{ 1, 0, 0x0040 }, /* P2: MINIPCIE1 (no OC) */
{ 1, 0, 0x0040 }, /* P3: MMC (no OC) */
{ 1, 2, 0x0080 }, /* P4: Front port (OC2) */
{ 0, 0, 0x0000 }, /* P5: Empty */
{ 0, 0, 0x0000 }, /* P6: Empty */
{ 0, 0, 0x0000 }, /* P7: Empty */
{ 1, 4, 0x0040 }, /* P8: Back port (OC4) */
{ 1, 4, 0x0040 }, /* P9: MINIPCIE3 (no OC) */
{ 1, 4, 0x0040 }, /* P10: BLUETOOTH (no OC) */
{ 0, 4, 0x0000 }, /* P11: Empty */
{ 1, 6, 0x0040 }, /* P12: Back port (OC6) */
{ 1, 5, 0x0040 }, /* P13: Back port (OC5) */
},
};
timestamp_init(get_initial_timestamp());
timestamp_add_now(TS_START_ROMSTAGE);
if (bist == 0)
enable_lapic();
pch_enable_lpc();
/* Enable GPIOs */
pci_write_config32(PCH_LPC_DEV, GPIO_BASE, DEFAULT_GPIOBASE|1);
pci_write_config8(PCH_LPC_DEV, GPIO_CNTL, 0x10);
setup_pch_gpios(&stumpy_gpio_map);
setup_sio_gpios();
/* Early SuperIO setup */
it8772f_ac_resume_southbridge(DUMMY_DEV);
ite_kill_watchdog(GPIO_DEV);
ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
init_bootmode_straps();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
if (MCHBAR16(SSKPD) == 0xCAFE) {
printk(BIOS_DEBUG, "soft reset detected\n");
boot_mode = 1;
/* System is not happy after keyboard reset... */
printk(BIOS_DEBUG, "Issuing CF9 warm reset\n");
outb(0x6, 0xcf9);
halt();
}
/* Perform some early chipset initialization required
* before RAM initialization can work
*/
sandybridge_early_initialization(SANDYBRIDGE_MOBILE);
printk(BIOS_DEBUG, "Back from sandybridge_early_initialization()\n");
boot_mode = southbridge_detect_s3_resume() ? 2 : 0;
post_code(0x38);
/* Enable SPD ROMs and DDR-III DRAM */
enable_smbus();
/* Prepare USB controller early in S3 resume */
if (boot_mode == 2) {
/*
* For Stumpy the back USB ports are reset on resume
* so default to resetting the controller to make the
* kernel happy. There is a CMOS flag to disable the
* controller reset in case the kernel can tolerate
* the device power loss better in the future.
*/
u8 magic = cmos_read(CMOS_USB_RESET_DISABLE);
if (magic == USB_RESET_DISABLE_MAGIC) {
printk(BIOS_DEBUG, "USB Controller Reset Disabled\n");
enable_usb_bar();
} else {
printk(BIOS_DEBUG, "USB Controller Reset Enabled\n");
}
} else {
/* Ensure USB reset on resume is enabled at boot */
cmos_write(0, CMOS_USB_RESET_DISABLE);
}
post_code(0x39);
pei_data.boot_mode = boot_mode;
timestamp_add_now(TS_BEFORE_INITRAM);
sdram_initialize(&pei_data);
timestamp_add_now(TS_AFTER_INITRAM);
post_code(0x3a);
/* Perform some initialization that must run before stage2 */
early_pch_init();
post_code(0x3b);
rcba_config();
post_code(0x3c);
quick_ram_check();
post_code(0x3e);
cbmem_was_initted = !cbmem_recovery(boot_mode==2);
if (boot_mode!=2)
save_mrc_data(&pei_data);
if (boot_mode==2 && !cbmem_was_initted) {
/* Failed S3 resume, reset to come up cleanly */
outb(0x6, 0xcf9);
halt();
}
northbridge_romstage_finalize(boot_mode==2);
post_code(0x3f);
if (CONFIG_LPC_TPM) {
init_tpm(boot_mode == 2);
}
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const u16 spd_addr [] = {
DIMM0, DIMM2, 0, 0,
DIMM1, DIMM3, 0, 0,
DIMM4, DIMM6, 0, 0,
DIMM5, DIMM7, 0, 0,
};
int needs_reset;
unsigned bsp_apicid = 0, nodes;
struct mem_controller ctrl[8];
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
sio_setup();
}
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx);
lpc47b397_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
sio_gpio_setup();
setup_mb_resource_map();
needs_reset = setup_coherent_ht_domain();
wait_all_core0_started();
// It is said that we should start core1 after all core0 launched
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
needs_reset |= ht_setup_chains_x();
needs_reset |= ck804_early_setup_x();
if (needs_reset) {
printk(BIOS_INFO, "ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
nodes = get_nodes();
//It's the time to set ctrl now;
fill_mem_ctrl(nodes, ctrl, spd_addr);
enable_smbus();
memreset_setup();
sdram_initialize(nodes, ctrl);
post_cache_as_ram();
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr[] = {
// Node 0
DIMM0, DIMM2, 0, 0,
DIMM1, DIMM3, 0, 0,
// Node 1
DIMM4, DIMM6, 0, 0,
DIMM5, DIMM7, 0, 0,
};
struct sys_info *sysinfo = &sysinfo_car;
int needs_reset = 0;
unsigned bsp_apicid = 0;
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0. */
/* Allow the HT devices to be found. */
enumerate_ht_chain();
sio_setup();
}
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
/* FIXME: This should be part of the Super I/O code/config. */
pnp_enter_ext_func_mode(SERIAL_DEV);
/* Switch CLKSEL to 24MHz (default is 48MHz). Needed for serial! */
pnp_write_config(SERIAL_DEV, 0x24, 0);
w83627ehg_enable_dev(SERIAL_DEV, CONFIG_TTYS0_BASE);
pnp_exit_ext_func_mode(SERIAL_DEV);
setup_mb_resource_map();
console_init();
report_bist_failure(bist); /* Halt upon BIST failure. */
printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
print_debug("bsp_apicid=");
print_debug_hex8(bsp_apicid);
print_debug("\n");
#if CONFIG_MEM_TRAIN_SEQ == 1
/* In BSP so could hold all AP until sysinfo is in RAM. */
set_sysinfo_in_ram(0);
#endif
setup_coherent_ht_domain(); /* Routing table and start other core0. */
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
/* It is said that we should start core1 after all core0 launched
* becase optimize_link_coherent_ht is moved out from
* setup_coherent_ht_domain, so here need to make sure last core0 is
* started, esp for two way system (there may be APIC ID conflicts in
* that case).
*/
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
/* Set up chains and store link pair for optimization later. */
ht_setup_chains_x(sysinfo); /* Init sblnk and sbbusn, nodes, sbdn. */
#if CONFIG_SET_FIDVID
{
msr_t msr = rdmsr(0xc0010042);
print_debug("begin msr fid, vid ");
print_debug_hex32(msr.hi);
print_debug_hex32(msr.lo);
print_debug("\n");
}
enable_fid_change();
enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
init_fidvid_bsp(bsp_apicid);
{
msr_t msr = rdmsr(0xc0010042);
print_debug("end msr fid, vid ");
print_debug_hex32(msr.hi);
print_debug_hex32(msr.lo);
print_debug("\n");
}
#endif
init_timer(); /* Need to use TMICT to synconize FID/VID. */
needs_reset |= optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
needs_reset |= mcp55_early_setup_x();
/* fidvid change will issue one LDTSTOP and the HT change will be effective too. */
if (needs_reset) {
print_info("ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
/* It's the time to set ctrl in sysinfo now. */
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
enable_smbus();
/* All AP stopped? */
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
/* bsp switch stack to RAM and copy sysinfo RAM now. */
post_cache_as_ram();
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr[] = {
// Node 0
DIMM0, DIMM1, DIMM2, 0,
0, 0, 0, 0,
// Node 1
0, 0, 0, 0,
0, 0, 0, 0,
};
unsigned bsp_apicid = 0;
int needs_reset = 0;
struct sys_info *sysinfo = &sysinfo_car;
winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
enable_rom_decode();
print_info("now booting... fallback\n");
/* Is this a CPU only reset? Or is this a secondary CPU? */
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0. */
/* Allow the HT devices to be found. */
enumerate_ht_chain();
}
print_info("now booting... real_main\n");
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
/* Halt if there was a built in self test failure. */
report_bist_failure(bist);
setup_default_resource_map();
setup_coherent_ht_domain();
wait_all_core0_started();
print_info("now booting... Core0 started\n");
#if CONFIG_LOGICAL_CPUS
/* It is said that we should start core1 after all core0 launched. */
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
init_timer();
ht_setup_chains_x(sysinfo); /* Init sblnk and sbbusn, nodes, sbdn. */
needs_reset = optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
needs_reset |= k8t890_early_setup_ht();
if (needs_reset) {
print_debug("ht reset -\n");
soft_reset();
}
/* the HT settings needs to be OK, because link freq change may cause HT disconnect */
vt8237_sb_enable_fid_vid();
enable_fid_change();
init_fidvid_bsp(bsp_apicid);
/* Stop the APs so we can start them later in init. */
allow_all_aps_stop(bsp_apicid);
/* It's the time to set ctrl now. */
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
enable_smbus();
/* this seems to be some GPIO on the SMBus--in any case, setting these
* two bits reduces the pullup impedance of the bus lines and is required
* in order to be able to read SPD info */
smbus_write_byte(0x48, 0x07, smbus_read_byte(0x48, 0x07) | 0x80);
smbus_write_byte(0x4a, 0x07, smbus_read_byte(0x4a, 0x07) | 0x10);
unsigned char mask;
mask = 0;
// mask |= 1 /* AGP voltage 1.7 V (not verified, just vendor BIOS value) */
// mask |= 2 /* V-Link voltage 2.6 V (not verified either) */
smbus_write_byte(0x4a, 0x00, (smbus_read_byte(0x4a, 0x00) & ~0x0f) | (0x0f ^ (mask << 2)));
smbus_write_byte(0x4a, 0x01, (smbus_read_byte(0x4a, 0x01) & ~0x03) | (0x03 ^ mask));
mask = 25; /* RAM voltage in decivolts, valid range from 25 to 28 */
mask = 3 - (mask - 25);
smbus_write_byte(0x4a, 0x02, 0x4f | (mask << 4));
smbus_write_byte(0x4a, 0x03, 0x04 | mask);
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
post_cache_as_ram();
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const u16 spd_addr[] = { DIMM0, 0, 0, 0, DIMM1, 0, 0, 0, };
int needs_reset = 0;
u32 bsp_apicid = 0;
msr_t msr;
struct cpuid_result cpuid1;
struct sys_info *sysinfo = &sysinfo_car;
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
sb600_lpc_port80();
/* sb600_pci_port80(); */
}
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
enable_rs690_dev8();
sb600_lpc_init();
/* Pistachio used a FPGA to enable serial debug instead of a SIO
* and it doesn't require any special setup. */
console_init();
post_code(0x03);
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
printk(BIOS_DEBUG, "bsp_apicid=0x%x\n", bsp_apicid);
setup_pistachio_resource_map();
setup_coherent_ht_domain();
#if CONFIG_LOGICAL_CPUS
/* It is said that we should start core1 after all core0 launched */
wait_all_core0_started();
start_other_cores();
#endif
wait_all_aps_started(bsp_apicid);
/* it will set up chains and store link pair for optimization later,
* it will init sblnk and sbbusn, nodes, sbdn */
ht_setup_chains_x(sysinfo);
/* run _early_setup before soft-reset. */
rs690_early_setup();
sb600_early_setup();
post_code(0x04);
/* Check to see if processor is capable of changing FIDVID */
/* otherwise it will throw a GP# when reading FIDVID_STATUS */
cpuid1 = cpuid(0x80000007);
if ((cpuid1.edx & 0x6) == 0x6) {
/* Read FIDVID_STATUS */
msr=rdmsr(0xc0010042);
printk(BIOS_DEBUG, "begin msr fid, vid: hi=0x%x, lo=0x%x\n", msr.hi, msr.lo);
enable_fid_change();
enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
init_fidvid_bsp(bsp_apicid);
/* show final fid and vid */
msr=rdmsr(0xc0010042);
printk(BIOS_DEBUG, "end msr fid, vid: hi=0x%x, lo=0x%x\n", msr.hi, msr.lo);
} else {
printk(BIOS_DEBUG, "Changing FIDVID not supported\n");
}
post_code(0x05);
needs_reset = optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
rs690_htinit();
printk(BIOS_DEBUG, "needs_reset=0x%x\n", needs_reset);
post_code(0x06);
if (needs_reset) {
print_info("ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
/* It's the time to set ctrl now; */
printk(BIOS_DEBUG, "sysinfo->nodes: %2x sysinfo->ctrl: %p spd_addr: %p\n",
sysinfo->nodes, sysinfo->ctrl, spd_addr);
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
post_code(0x07);
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
post_code(0x08);
rs690_before_pci_init();
sb600_before_pci_init();
post_cache_as_ram();
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr [] = {
// Node 0
DIMM0, DIMM2, 0, 0,
DIMM1, DIMM3, 0, 0,
// Node 1
DIMM4, DIMM6, 0, 0,
DIMM5, DIMM7, 0, 0,
};
struct sys_info *sysinfo = &sysinfo_car;
int needs_reset = 0;
unsigned bsp_apicid = 0;
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
sio_setup();
}
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
#if 0
uint8_t tmp = 0;
pnp_enter_ext_func_mode(SERIAL_DEV);
/* The following line will set CLKIN to 24 MHz, external */
pnp_write_config(SERIAL_DEV, IT8716F_CONFIG_REG_CLOCKSEL, 0x11);
tmp = pnp_read_config(SERIAL_DEV, IT8716F_CONFIG_REG_SWSUSP);
/* Is serial flash enabled? Then enable writing to serial flash. */
if (tmp & 0x0e) {
pnp_write_config(SERIAL_DEV, IT8716F_CONFIG_REG_SWSUSP, tmp | 0x10);
pnp_set_logical_device(GPIO_DEV);
/* Set Serial Flash interface to 0x0820 */
pnp_write_config(GPIO_DEV, 0x64, 0x08);
pnp_write_config(GPIO_DEV, 0x65, 0x20);
}
it8716f_enable_dev(SERIAL_DEV, CONFIG_TTYS0_BASE);
pnp_exit_ext_func_mode(SERIAL_DEV);
#endif
ite_conf_clkin(CLKIN_DEV, ITE_UART_CLK_PREDIVIDE_48);
ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
setup_mb_resource_map();
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\n");
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
setup_coherent_ht_domain(); // routing table and start other core0
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
// It is said that we should start core1 after all core0 launched
/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
* So here need to make sure last core0 is started, esp for two way system,
* (there may be apic id conflicts in that case)
*/
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
/* it will set up chains and store link pair for optimization later */
ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn
#if CONFIG_SET_FIDVID
{
msr_t msr;
msr=rdmsr(0xc0010042);
print_debug("begin msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
}
enable_fid_change();
enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
init_fidvid_bsp(bsp_apicid);
// show final fid and vid
{
msr_t msr;
msr=rdmsr(0xc0010042);
print_debug("end msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
}
#endif
init_timer(); // Need to use TMICT to synconize FID/VID
needs_reset |= optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
needs_reset |= mcp55_early_setup_x();
// fidvid change will issue one LDTSTOP and the HT change will be effective too
if (needs_reset) {
print_info("ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
//It's the time to set ctrl in sysinfo now;
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
enable_smbus();
/* all ap stopped? */
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
post_cache_as_ram(); // bsp swtich stack to ram and copy sysinfo ram now
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr[] = {
//first node
RC0|DIMM0, RC0|DIMM2, RC0|DIMM4, RC0|DIMM6,
RC0|DIMM1, RC0|DIMM3, RC0|DIMM5, RC0|DIMM7,
//second node
RC1|DIMM0, RC1|DIMM2, RC1|DIMM4, RC1|DIMM6,
RC1|DIMM1, RC1|DIMM3, RC1|DIMM5, RC1|DIMM7,
};
struct sys_info *sysinfo = (struct sys_info *)(CONFIG_DCACHE_RAM_BASE +
CONFIG_DCACHE_RAM_SIZE - CONFIG_DCACHE_RAM_GLOBAL_VAR_SIZE);
int needs_reset;
unsigned bsp_apicid = 0;
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
bcm5785_enable_lpc();
//enable RTC
pc87417_enable_dev(RTC_DEV);
}
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
pc87417_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
// dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x200, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE);
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
setup_ms9185_resource_map();
#if 0
dump_pci_device(PCI_DEV(0, 0x18, 0));
dump_pci_device(PCI_DEV(0, 0x19, 0));
#endif
print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\n");
setup_coherent_ht_domain();
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS==1
// It is said that we should start core1 after all core0 launched
/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
* So here need to make sure last core0 is started, esp for two way system,
* (there may be apic id conflicts in that case)
*/
start_other_cores();
//bx_a010- wait_all_other_cores_started(bsp_apicid);
#endif
/* it will set up chains and store link pair for optimization later */
ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn
bcm5785_early_setup();
#if 0
//it your CPU min fid is 1G, you can change HT to 1G and FID to max one time.
needs_reset = optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
#endif
#if CONFIG_SET_FIDVID
{
msr_t msr;
msr=rdmsr(0xc0010042);
print_debug("begin msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
}
enable_fid_change();
enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
init_fidvid_bsp(bsp_apicid);
// show final fid and vid
{
msr_t msr;
msr=rdmsr(0xc0010042);
print_debug("end msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
}
#endif
#if 1
needs_reset = optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
// fidvid change will issue one LDTSTOP and the HT change will be effective too
if (needs_reset) {
print_info("ht reset -\n");
soft_reset();
}
#endif
allow_all_aps_stop(bsp_apicid);
//It's the time to set ctrl in sysinfo now;
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
enable_smbus();
#if 0
int i;
for(i=0;i<2;i++) {
activate_spd_rom(sysinfo->ctrl+i);
dump_smbus_registers();
}
#endif
#if 0
int i;
for(i=1;i<256;i<<=1) {
change_i2c_mux(i);
dump_smbus_registers();
}
#endif
//do we need apci timer, tsc...., only debug need it for better output
/* all ap stopped? */
// init_timer(); // Need to use TMICT to synconize FID/VID
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
#if 0
print_pci_devices();
#endif
#if 0
// dump_pci_devices();
dump_pci_device_index_wait(PCI_DEV(0, 0x18, 2), 0x98);
dump_pci_device_index_wait(PCI_DEV(0, 0x19, 2), 0x98);
#endif
post_cache_as_ram();
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr[] = {
//first node
RC0|DIMM0, RC0|DIMM2, 0, 0,
RC0|DIMM1, RC0|DIMM3, 0, 0,
#if CONFIG_MAX_PHYSICAL_CPUS > 1
//second node
RC1|DIMM0, RC1|DIMM2, RC1|DIMM4, RC1|DIMM6,
RC1|DIMM1, RC1|DIMM3, RC1|DIMM5, RC1|DIMM7,
#endif
#if CONFIG_MAX_PHYSICAL_CPUS > 2
// third node
RC2|DIMM0, RC2|DIMM2, 0, 0,
RC2|DIMM1, RC2|DIMM3, 0, 0,
// four node
RC3|DIMM0, RC3|DIMM2, RC3|DIMM4, RC3|DIMM6,
RC3|DIMM1, RC3|DIMM3, RC3|DIMM5, RC3|DIMM7,
#endif
};
struct sys_info *sysinfo = &sysinfo_car;
int needs_reset;
unsigned bsp_apicid = 0;
#if CONFIG_SET_FIDVID
struct cpuid_result cpuid1;
#endif
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
// dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x200, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE);
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
setup_mb_resource_map();
#if 0
dump_pci_device(PCI_DEV(0, 0x18, 0));
dump_pci_device(PCI_DEV(0, 0x19, 0));
#endif
print_debug("bsp_apicid="); print_debug_hex8(bsp_apicid); print_debug("\n");
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
setup_coherent_ht_domain(); // routing table and start other core0
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
// It is said that we should start core1 after all core0 launched
/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
* So here need to make sure last core0 is started, esp for two way system,
* (there may be apic id conflicts in that case)
*/
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
/* it will set up chains and store link pair for optimization later */
ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn
#if 0
//it your CPU min fid is 1G, you can change HT to 1G and FID to max one time.
needs_reset = optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
#endif
#if CONFIG_SET_FIDVID
/* Check to see if processor is capable of changing FIDVID */
/* otherwise it will throw a GP# when reading FIDVID_STATUS */
cpuid1 = cpuid(0x80000007);
if ((cpuid1.edx & 0x6) == 0x6) {
{
/* Read FIDVID_STATUS */
msr_t msr;
msr=rdmsr(0xc0010042);
print_debug("begin msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
}
enable_fid_change();
enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
init_fidvid_bsp(bsp_apicid);
// show final fid and vid
{
msr_t msr;
msr=rdmsr(0xc0010042);
print_debug("end msr fid, vid "); print_debug_hex32( msr.hi ); print_debug_hex32(msr.lo); print_debug("\n");
}
} else {
print_debug("Changing FIDVID not supported\n");
}
#endif
#if 1
needs_reset = optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
// fidvid change will issue one LDTSTOP and the HT change will be effective too
if (needs_reset) {
print_info("ht reset -\n");
soft_reset_x(sysinfo->sbbusn, sysinfo->sbdn);
}
#endif
allow_all_aps_stop(bsp_apicid);
//It's the time to set ctrl in sysinfo now;
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
enable_smbus();
#if 0
int i;
for(i=0;i<4;i++) {
activate_spd_rom(&cpu[i]);
dump_smbus_registers();
}
#endif
memreset_setup();
//do we need apci timer, tsc...., only debug need it for better output
/* all ap stopped? */
// init_timer(); // Need to use TMICT to synconize FID/VID
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
#if 0
print_pci_devices();
#endif
#if 0
// dump_pci_devices();
dump_pci_device_index_wait(PCI_DEV(0, 0x18, 2), 0x98);
dump_pci_device_index_wait(PCI_DEV(0, 0x19, 2), 0x98);
#endif
post_cache_as_ram(); // bsp swtich stack to ram and copy sysinfo ram now
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
/* The SPD is being read from the CPU1 (marked CPU2 on the board) and we
don't know how to switch the SMBus to decode the CPU0 SPDs. So, The
memory on each CPU must be an exact match.
*/
static const uint16_t spd_addr[] = {
// Node 0
RC0 | DIMM0, RC0 | DIMM2,
RC0 | DIMM4, RC0 | DIMM6,
RC0 | DIMM1, RC0 | DIMM3,
RC0 | DIMM5, RC0 | DIMM7,
// Node 1
RC1 | DIMM0, RC1 | DIMM2,
RC1 | DIMM4, RC1 | DIMM6,
RC1 | DIMM1, RC1 | DIMM3,
RC1 | DIMM5, RC1 | DIMM7,
};
struct sys_info *sysinfo = &sysinfo_car;
int needs_reset = 0;
unsigned bsp_apicid = 0;
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
sio_setup();
}
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
w83627hf_set_clksel_48(DUMMY_DEV);
winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
setup_mb_resource_map();
printk(BIOS_DEBUG, "bsp_apicid=%02x\n", bsp_apicid);
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
#if CONFIG_DEBUG_SMBUS
dump_smbus_registers();
#endif
setup_coherent_ht_domain(); // routing table and start other core0
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
// It is said that we should start core1 after all core0 launched
/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
* So here need to make sure last core0 is started, esp for two way system,
* (there may be apic id conflicts in that case)
*/
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
/* it will set up chains and store link pair for optimization later */
ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn
#if CONFIG_SET_FIDVID
{
msr_t msr;
msr = rdmsr(0xc0010042);
printk(BIOS_DEBUG, "begin msr fid, vid %08x%08x\n", msr.hi, msr.lo);
}
enable_fid_change();
enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
init_fidvid_bsp(bsp_apicid);
// show final fid and vid
{
msr_t msr;
msr = rdmsr(0xc0010042);
printk(BIOS_DEBUG, "end msr fid, vid %08x%08x\n", msr.hi, msr.lo);
}
#endif
init_timer(); /* Need to use TMICT to synchronize FID/VID. */
needs_reset |= optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
needs_reset |= mcp55_early_setup_x();
// fidvid change will issue one LDTSTOP and the HT change will be effective too
if (needs_reset) {
printk(BIOS_INFO, "ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
//It's the time to set ctrl in sysinfo now;
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
enable_smbus(); /* enable in sio_setup */
/* all ap stopped? */
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
post_cache_as_ram(); // bsp swtich stack to RAM and copy sysinfo RAM now
}
void romstage_common(const struct romstage_params *params)
{
int boot_mode;
int wake_from_s3;
timestamp_init(get_initial_timestamp());
timestamp_add_now(TS_START_ROMSTAGE);
if (params->bist == 0)
enable_lapic();
wake_from_s3 = early_pch_init(params->gpio_map, params->rcba_config);
#if CONFIG_EC_GOOGLE_CHROMEEC
/* Ensure the EC is in the right mode for recovery */
google_chromeec_early_init();
#endif
/* Halt if there was a built in self test failure */
report_bist_failure(params->bist);
/* Perform some early chipset initialization required
* before RAM initialization can work
*/
haswell_early_initialization(HASWELL_MOBILE);
printk(BIOS_DEBUG, "Back from haswell_early_initialization()\n");
if (wake_from_s3) {
#if CONFIG_HAVE_ACPI_RESUME
printk(BIOS_DEBUG, "Resume from S3 detected.\n");
#else
printk(BIOS_DEBUG, "Resume from S3 detected, but disabled.\n");
wake_from_s3 = 0;
#endif
}
/* There are hard coded assumptions of 2 meaning s3 wake. Normalize
* the users of the 2 literal here based off wake_from_s3. */
boot_mode = wake_from_s3 ? 2 : 0;
/* Prepare USB controller early in S3 resume */
if (wake_from_s3)
enable_usb_bar();
post_code(0x3a);
params->pei_data->boot_mode = boot_mode;
timestamp_add_now(TS_BEFORE_INITRAM);
report_platform_info();
if (params->copy_spd != NULL)
params->copy_spd(params->pei_data);
sdram_initialize(params->pei_data);
timestamp_add_now(TS_AFTER_INITRAM);
post_code(0x3b);
intel_early_me_status();
quick_ram_check();
post_code(0x3e);
if (!wake_from_s3) {
cbmem_initialize_empty();
/* Save data returned from MRC on non-S3 resumes. */
save_mrc_data(params->pei_data);
} else if (cbmem_initialize()) {
#if CONFIG_HAVE_ACPI_RESUME
/* Failed S3 resume, reset to come up cleanly */
reset_system();
#endif
}
romstage_handoff_init(wake_from_s3);
post_code(0x3f);
if (IS_ENABLED(CONFIG_LPC_TPM))
init_tpm(wake_from_s3);
}
void main(unsigned long bist)
{
int boot_mode = 0;
int cbmem_was_initted;
struct pei_data pei_data = {
.pei_version = PEI_VERSION,
.mchbar = (uintptr_t)DEFAULT_MCHBAR,
.dmibar = (uintptr_t)DEFAULT_DMIBAR,
.epbar = DEFAULT_EPBAR,
.pciexbar = CONFIG_MMCONF_BASE_ADDRESS,
.smbusbar = SMBUS_IO_BASE,
.wdbbar = 0x4000000,
.wdbsize = 0x1000,
.hpet_address = CONFIG_HPET_ADDRESS,
.rcba = (uintptr_t)DEFAULT_RCBABASE,
.pmbase = DEFAULT_PMBASE,
.gpiobase = DEFAULT_GPIOBASE,
.thermalbase = 0xfed08000,
.system_type = 0, // 0 Mobile, 1 Desktop/Server
.tseg_size = CONFIG_SMM_TSEG_SIZE,
.spd_addresses = { 0xa0, 0x00, 0xa4, 0x00 },
.ts_addresses = { 0x00, 0x00, 0x00, 0x00 },
.ec_present = 0,
// 0 = leave channel enabled
// 1 = disable dimm 0 on channel
// 2 = disable dimm 1 on channel
// 3 = disable dimm 0+1 on channel
.dimm_channel0_disabled = 2,
.dimm_channel1_disabled = 2,
.max_ddr3_freq = 1600,
.usb_port_config = {
{ 1, 0, 0x0040 }, /* P0: Front port (OC0) */
{ 1, 1, 0x0040 }, /* P1: Back port (OC1) */
{ 1, 0, 0x0040 }, /* P2: MINIPCIE1 (no OC) */
{ 1, 0, 0x0040 }, /* P3: MMC (no OC) */
{ 1, 2, 0x0040 }, /* P4: Front port (OC2) */
{ 0, 0, 0x0000 }, /* P5: Empty */
{ 0, 0, 0x0000 }, /* P6: Empty */
{ 0, 0, 0x0000 }, /* P7: Empty */
{ 1, 4, 0x0040 }, /* P8: Back port (OC4) */
{ 1, 4, 0x0040 }, /* P9: MINIPCIE3 (no OC) */
{ 1, 4, 0x0040 }, /* P10: BLUETOOTH (no OC) */
{ 0, 4, 0x0000 }, /* P11: Empty */
{ 1, 6, 0x0040 }, /* P12: Back port (OC6) */
{ 1, 5, 0x0040 }, /* P13: Back port (OC5) */
},
};
timestamp_init(get_initial_timestamp());
timestamp_add_now(TS_START_ROMSTAGE);
if (bist == 0)
enable_lapic();
pch_enable_lpc();
/* Enable GPIOs */
pci_write_config32(PCH_LPC_DEV, GPIO_BASE, DEFAULT_GPIOBASE|1);
pci_write_config8(PCH_LPC_DEV, GPIO_CNTL, 0x10);
setup_pch_gpios(&emeraldlake2_gpio_map);
setup_sio_gpios();
/* Early SuperIO setup */
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
if (MCHBAR16(SSKPD) == 0xCAFE) {
printk(BIOS_DEBUG, "soft reset detected\n");
boot_mode = 1;
/* System is not happy after keyboard reset... */
printk(BIOS_DEBUG, "Issuing CF9 warm reset\n");
outb(0x6, 0xcf9);
halt();
}
/* Perform some early chipset initialization required
* before RAM initialization can work
*/
sandybridge_early_initialization(SANDYBRIDGE_MOBILE);
printk(BIOS_DEBUG, "Back from sandybridge_early_initialization()\n");
boot_mode = southbridge_detect_s3_resume() ? 2 : 0;
post_code(0x38);
/* Enable SPD ROMs and DDR-III DRAM */
enable_smbus();
/* Prepare USB controller early in S3 resume */
if (boot_mode == 2)
enable_usb_bar();
post_code(0x3a);
pei_data.boot_mode = boot_mode;
timestamp_add_now(TS_BEFORE_INITRAM);
sdram_initialize(&pei_data);
timestamp_add_now(TS_AFTER_INITRAM);
post_code(0x3b);
/* Perform some initialization that must run before stage2 */
early_pch_init();
post_code(0x3c);
/* This should probably go away. Until now it is required
* and mainboard specific
*/
rcba_config();
post_code(0x3d);
quick_ram_check();
post_code(0x3e);
cbmem_was_initted = !cbmem_recovery(boot_mode==2);
if (boot_mode!=2)
save_mrc_data(&pei_data);
if (boot_mode==2 && !cbmem_was_initted) {
/* Failed S3 resume, reset to come up cleanly */
outb(0x6, 0xcf9);
halt();
}
northbridge_romstage_finalize(boot_mode==2);
post_code(0x3f);
if (CONFIG_LPC_TPM) {
init_tpm(boot_mode == 2);
}
}
void romstage_common(const struct romstage_params *params)
{
int boot_mode;
int wake_from_s3;
struct romstage_handoff *handoff;
#if CONFIG_COLLECT_TIMESTAMPS
uint64_t start_romstage_time;
uint64_t before_dram_time;
uint64_t after_dram_time;
uint64_t base_time =
(uint64_t)pci_read_config32(PCI_DEV(0, 0x1f, 2), 0xd0) << 32 ||
pci_read_config32(PCI_DEV(0, 0x00, 0), 0xdc);
#endif
#if CONFIG_COLLECT_TIMESTAMPS
start_romstage_time = timestamp_get();
#endif
if (params->bist == 0)
enable_lapic();
wake_from_s3 = early_pch_init(params->gpio_map, params->rcba_config);
#if CONFIG_EC_GOOGLE_CHROMEEC
/* Ensure the EC is in the right mode for recovery */
google_chromeec_early_init();
#endif
/* Halt if there was a built in self test failure */
report_bist_failure(params->bist);
/* Perform some early chipset initialization required
* before RAM initialization can work
*/
haswell_early_initialization(HASWELL_MOBILE);
printk(BIOS_DEBUG, "Back from haswell_early_initialization()\n");
if (wake_from_s3) {
#if CONFIG_HAVE_ACPI_RESUME
printk(BIOS_DEBUG, "Resume from S3 detected.\n");
#else
printk(BIOS_DEBUG, "Resume from S3 detected, but disabled.\n");
wake_from_s3 = 0;
#endif
}
/* There are hard coded assumptions of 2 meaning s3 wake. Normalize
* the users of the 2 literal here based off wake_from_s3. */
boot_mode = wake_from_s3 ? 2 : 0;
/* Prepare USB controller early in S3 resume */
if (wake_from_s3)
enable_usb_bar();
post_code(0x3a);
params->pei_data->boot_mode = boot_mode;
#if CONFIG_COLLECT_TIMESTAMPS
before_dram_time = timestamp_get();
#endif
report_platform_info();
if (params->copy_spd != NULL)
params->copy_spd(params->pei_data);
sdram_initialize(params->pei_data);
#if CONFIG_COLLECT_TIMESTAMPS
after_dram_time = timestamp_get();
#endif
post_code(0x3b);
intel_early_me_status();
quick_ram_check();
post_code(0x3e);
if (!wake_from_s3) {
cbmem_initialize_empty();
/* Save data returned from MRC on non-S3 resumes. */
save_mrc_data(params->pei_data);
} else if (cbmem_initialize()) {
#if CONFIG_HAVE_ACPI_RESUME
/* Failed S3 resume, reset to come up cleanly */
reset_system();
#endif
}
handoff = romstage_handoff_find_or_add();
if (handoff != NULL)
handoff->s3_resume = wake_from_s3;
else
printk(BIOS_DEBUG, "Romstage handoff structure not added!\n");
post_code(0x3f);
#if CONFIG_CHROMEOS
init_chromeos(boot_mode);
#endif
#if CONFIG_COLLECT_TIMESTAMPS
timestamp_init(base_time);
timestamp_add(TS_START_ROMSTAGE, start_romstage_time );
timestamp_add(TS_BEFORE_INITRAM, before_dram_time );
timestamp_add(TS_AFTER_INITRAM, after_dram_time );
timestamp_add_now(TS_END_ROMSTAGE);
#endif
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr [] = {
//first node
RC0|DIMM0, RC0|DIMM2, 0, 0,
RC0|DIMM1, RC0|DIMM3, 0, 0,
#if CONFIG_MAX_PHYSICAL_CPUS > 1
//second node
RC1|DIMM0, RC1|DIMM2, 0, 0,
RC1|DIMM1, RC1|DIMM3, 0, 0,
#endif
};
struct sys_info *sysinfo = &sysinfo_car;
int needs_reset = 0;
unsigned bsp_apicid = 0;
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx,sysinfo);
winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
setup_dl145g1_resource_map();
//setup_default_resource_map();
setup_coherent_ht_domain();
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
// It is said that we should start core1 after all core0 launched
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
ht_setup_chains_x(sysinfo);
#if CONFIG_SET_FIDVID
/* Check to see if processor is capable of changing FIDVID */
/* otherwise it will throw a GP# when reading FIDVID_STATUS */
struct cpuid_result cpuid1 = cpuid(0x80000007);
if ((cpuid1.edx & 0x6) == 0x6) {
{
/* Read FIDVID_STATUS */
msr_t msr;
msr = rdmsr(0xc0010042);
printk(BIOS_DEBUG, "begin msr fid, vid %08x%08x\n", msr.hi, msr.lo);
}
enable_fid_change();
enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
init_fidvid_bsp(bsp_apicid);
// show final fid and vid
{
msr_t msr;
msr = rdmsr(0xc0010042);
printk(BIOS_DEBUG, "end msr fid, vid %08x%08x\n", msr.hi, msr.lo);
}
} else {
printk(BIOS_DEBUG, "Changing FIDVID not supported\n");
}
#endif
needs_reset |= optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
if (needs_reset) {
printk(BIOS_INFO, "ht reset -\n");
soft_reset_x(sysinfo->sbbusn, sysinfo->sbdn);
}
enable_smbus();
int i;
for(i = 0; i < 2; i++) {
activate_spd_rom(&sysinfo->ctrl[i]);
}
for(i = RC0; i <= RC1; i<<=1) {
change_i2c_mux(i);
}
//dump_spd_registers(&sysinfo->ctrl[0]);
//dump_spd_registers(&sysinfo->ctrl[1]);
//dump_smbus_registers();
allow_all_aps_stop(bsp_apicid);
//It's the time to set ctrl now;
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
memreset_setup();
#if CONFIG_SET_FIDVID
init_timer(); // Need to use TMICT to synchronize FID/VID
#endif
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
//dump_pci_devices();
post_cache_as_ram();
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr[] = {
// Node 0
DIMM0, DIMM2, 0, 0,
0, 0, 0, 0,
// Node 1
DIMM1, DIMM3, 0, 0,
0, 0, 0, 0,
};
unsigned bsp_apicid = 0;
int needs_reset = 0;
struct sys_info *sysinfo = &sysinfo_car;
sio_init();
w83627ehg_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
enable_rom_decode();
print_info("now booting... fallback\n");
/* Is this a CPU only reset? Or is this a secondary CPU? */
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0. */
/* Allow the HT devices to be found. */
enumerate_ht_chain();
}
// FIXME why is this executed again? --->
sio_init();
w83627ehg_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
enable_rom_decode();
// <--- FIXME why is this executed again?
print_info("now booting... real_main\n");
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
/* Halt if there was a built in self test failure. */
report_bist_failure(bist);
setup_default_resource_map();
setup_coherent_ht_domain();
wait_all_core0_started();
print_info("now booting... Core0 started\n");
#if CONFIG_LOGICAL_CPUS
/* It is said that we should start core1 after all core0 launched. */
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
init_timer();
ht_setup_chains_x(sysinfo); /* Init sblnk and sbbusn, nodes, sbdn. */
needs_reset = optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
needs_reset |= k8t890_early_setup_ht();
if (needs_reset) {
print_debug("ht reset -\n");
soft_reset();
}
/* the HT settings needs to be OK, because link freq chnage may cause HT disconnect */
enable_fid_change();
init_fidvid_bsp(bsp_apicid);
/* Stop the APs so we can start them later in init. */
allow_all_aps_stop(bsp_apicid);
/* It's the time to set ctrl now. */
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
enable_smbus();
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
post_cache_as_ram();
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr[] = {
DIMM0, DIMM2, 0, 0,
DIMM1, DIMM3, 0, 0,
#if CONFIG_MAX_PHYSICAL_CPUS > 1
DIMM4, DIMM6, 0, 0,
DIMM5, DIMM7, 0, 0,
#endif
};
int needs_reset;
unsigned nodes, bsp_apicid = 0;
struct mem_controller ctrl[8];
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
sio_setup();
}
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx);
it8712f_24mhz_clkin();
it8712f_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
#if 0
dump_pci_device(PCI_DEV(0, 0x18, 0));
#endif
needs_reset = setup_coherent_ht_domain();
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
/* It is said that we should start core1 after all core0 launched. */
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
needs_reset |= ht_setup_chains_x();
needs_reset |= ck804_early_setup_x();
if (needs_reset) {
print_info("ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
nodes = get_nodes();
/* It's the time to set ctrl now. */
fill_mem_ctrl(nodes, ctrl, spd_addr);
enable_smbus();
#if 0
dump_spd_registers(&ctrl[0]);
dump_smbus_registers();
#endif
sdram_initialize(nodes, ctrl);
#if 0
print_pci_devices();
dump_pci_devices();
#endif
post_cache_as_ram();
}
void main(unsigned long bist)
{
int s3resume = 0;
const u8 spd_addrmap[2 * DIMM_SOCKETS] = { 0x50, 0x51, 0x52, 0x53 };
timestamp_init(get_initial_timestamp());
timestamp_add_now(TS_START_ROMSTAGE);
if (bist == 0)
enable_lapic();
/* Force PCIRST# */
pci_write_config16(PCI_DEV(0, 0x1e, 0), BCTRL, SBR);
udelay(200 * 1000);
pci_write_config16(PCI_DEV(0, 0x1e, 0), BCTRL, 0);
ich7_enable_lpc();
/* Set up the console */
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
if (MCHBAR16(SSKPD) == 0xCAFE) {
printk(BIOS_DEBUG,
"Soft reset detected, rebooting properly.\n");
outb(0x6, 0xcf9);
halt();
}
/* Perform some early chipset initialization required
* before RAM initialization can work
*/
i945_early_initialization();
s3resume = southbridge_detect_s3_resume();
/* Enable SPD ROMs and DDR-II DRAM */
enable_smbus();
#if CONFIG_DEFAULT_CONSOLE_LOGLEVEL > 8
dump_spd_registers();
#endif
timestamp_add_now(TS_BEFORE_INITRAM);
sdram_initialize(s3resume ? 2 : 0, spd_addrmap);
timestamp_add_now(TS_AFTER_INITRAM);
/* Perform some initialization that must run before stage2 */
early_ich7_init();
/* This should probably go away. Until now it is required
* and mainboard specific
*/
rcba_config();
/* Chipset Errata! */
fixup_i945_errata();
/* Initialize the internal PCIe links before we go into stage2 */
i945_late_initialization(s3resume);
timestamp_add_now(TS_END_ROMSTAGE);
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const u16 spd_addr[] = { DIMM0, 0, 0, 0, DIMM1, 0, 0, 0, };
int needs_reset = 0;
u32 bsp_apicid = 0;
msr_t msr;
struct cpuid_result cpuid1;
struct sys_info *sysinfo = &sysinfo_car;
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
/* sb600_lpc_port80(); */
sb600_pci_port80();
}
technexion_post_code_init();
technexion_post_code(LED_MESSAGE_START);
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
enable_rs690_dev8();
sb600_lpc_init();
ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
ite_kill_watchdog(GPIO_DEV);
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
printk(BIOS_DEBUG, "bsp_apicid=0x%x\n", bsp_apicid);
setup_tim5690_resource_map();
setup_coherent_ht_domain();
#if CONFIG_LOGICAL_CPUS
/* It is said that we should start core1 after all core0 launched */
wait_all_core0_started();
start_other_cores();
#endif
wait_all_aps_started(bsp_apicid);
ht_setup_chains_x(sysinfo);
/* run _early_setup before soft-reset. */
rs690_early_setup();
sb600_early_setup();
/* Check to see if processor is capable of changing FIDVID */
/* otherwise it will throw a GP# when reading FIDVID_STATUS */
cpuid1 = cpuid(0x80000007);
if ((cpuid1.edx & 0x6) == 0x6) {
/* Read FIDVID_STATUS */
msr=rdmsr(0xc0010042);
printk(BIOS_DEBUG, "begin msr fid, vid: hi=0x%x, lo=0x%x\n", msr.hi, msr.lo);
enable_fid_change();
enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
init_fidvid_bsp(bsp_apicid);
/* show final fid and vid */
msr=rdmsr(0xc0010042);
printk(BIOS_DEBUG, "end msr fid, vid: hi=0x%x, lo=0x%x\n", msr.hi, msr.lo);
} else {
printk(BIOS_DEBUG, "Changing FIDVID not supported\n");
}
needs_reset = optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
rs690_htinit();
printk(BIOS_DEBUG, "needs_reset=0x%x\n", needs_reset);
if (needs_reset) {
printk(BIOS_INFO, "ht reset -\n");
soft_reset();
}
speaker_init(255);
speaker_on_nodelay();
allow_all_aps_stop(bsp_apicid);
/* It's the time to set ctrl now; */
printk(BIOS_DEBUG, "sysinfo->nodes: %2x sysinfo->ctrl: %p spd_addr: %p\n",
sysinfo->nodes, sysinfo->ctrl, spd_addr);
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
technexion_post_code(LED_MESSAGE_RAM);
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
speaker_off_nodelay();
rs690_before_pci_init();
sb600_before_pci_init();
post_cache_as_ram();
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr [] = {
// Node 0
DIMM0, DIMM2, 0, 0,
DIMM1, DIMM3, 0, 0,
// Node 1
DIMM4, DIMM6, 0, 0,
DIMM5, DIMM7, 0, 0,
};
struct sys_info *sysinfo = &sysinfo_car;
int needs_reset = 0;
unsigned bsp_apicid = 0;
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
sio_setup();
}
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
setup_mb_resource_map();
dme1737_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
printk(BIOS_DEBUG, "bsp_apicid=%02x\n", bsp_apicid);
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
setup_coherent_ht_domain(); // routing table and start other core0
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
// It is said that we should start core1 after all core0 launched
/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
* So here need to make sure last core0 is started, esp for two way system,
* (there may be apic id conflicts in that case)
*/
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
/* it will set up chains and store link pair for optimization later */
ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn
#if CONFIG_SET_FIDVID
{
msr_t msr;
msr=rdmsr(0xc0010042);
printk(BIOS_DEBUG, "begin msr fid, vid %08x%08x\n", msr.hi, msr.lo);
}
enable_fid_change();
enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
init_fidvid_bsp(bsp_apicid);
// show final fid and vid
{
msr_t msr;
msr=rdmsr(0xc0010042);
printk(BIOS_DEBUG, "end msr fid, vid %08x%08x\n", msr.hi, msr.lo);
}
#endif
init_timer(); /* Need to use TMICT to synchronize FID/VID. */
needs_reset |= optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
needs_reset |= mcp55_early_setup_x();
/* mask NMI from constantly-asserted-on-this-board SERR# */
outb((inb(NMI_SC) & 0x0f) | PCI_SERR_EN, NMI_SC);
// fidvid change will issue one LDTSTOP and the HT change will be effective too
if (needs_reset) {
printk(BIOS_INFO, "ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
//It's the time to set ctrl in sysinfo now;
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
enable_smbus();
/* all ap stopped? */
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
post_cache_as_ram(); // bsp swtich stack to ram and copy sysinfo ram now
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr[] = {
// first node
DIMM0, DIMM2, 0, 0,
DIMM1, DIMM3, 0, 0,
// second node
DIMM4, DIMM6, 0, 0,
DIMM5, DIMM7, 0, 0,
};
struct sys_info *sysinfo = &sysinfo_car;
int needs_reset;
unsigned bsp_apicid = 0;
if (!cpu_init_detectedx && boot_cpu()) {
/* Nothing special needs to be done to find bus 0 */
/* Allow the HT devices to be found */
enumerate_ht_chain();
bcm5785_enable_lpc();
pc87417_enable_dev(RTC_DEV); /* Enable RTC */
}
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
pilot_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
// setup_early_ipmi_serial();
pilot_early_init(SERIAL_DEV); //config port is being taken from SERIAL_DEV
printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
printk(BIOS_DEBUG, "bsp_apicid=%02x\n", bsp_apicid);
#if CONFIG_MEM_TRAIN_SEQ == 1
set_sysinfo_in_ram(0); // in BSP so could hold all ap until sysinfo is in ram
#endif
setup_coherent_ht_domain();
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
// It is said that we should start core1 after all core0 launched
/* becase optimize_link_coherent_ht is moved out from setup_coherent_ht_domain,
* So here need to make sure last core0 is started, esp for two way system,
* (there may be apic id conflicts in that case)
*/
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
/* it will set up chains and store link pair for optimization later */
ht_setup_chains_x(sysinfo); // it will init sblnk and sbbusn, nodes, sbdn
bcm5785_early_setup();
#if CONFIG_SET_FIDVID
{
msr_t msr;
msr=rdmsr(0xc0010042);
printk(BIOS_DEBUG, "begin msr fid, vid %08x %08x\n", msr.hi, msr.lo);
}
enable_fid_change();
enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);
init_fidvid_bsp(bsp_apicid);
// show final fid and vid
{
msr_t msr;
msr=rdmsr(0xc0010042);
printk(BIOS_DEBUG, "end msr fid, vid %08x %08x\n", msr.hi, msr.lo);
}
#endif
needs_reset = optimize_link_coherent_ht();
needs_reset |= optimize_link_incoherent_ht(sysinfo);
// fidvid change will issue one LDTSTOP and the HT change will be effective too
if (needs_reset) {
printk(BIOS_INFO, "ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
//It's the time to set ctrl in sysinfo now;
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
enable_smbus();
//do we need apci timer, tsc...., only debug need it for better output
/* all ap stopped? */
// init_timer(); // Need to use TMICT to synconize FID/VID
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
post_cache_as_ram();
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr [] = {
DIMM0, DIMM2, 0, 0,
DIMM1, DIMM3, 0, 0,
#if CONFIG_MAX_PHYSICAL_CPUS > 1
DIMM4, DIMM6, 0, 0,
DIMM5, DIMM7, 0, 0,
#endif
};
int needs_reset;
unsigned bsp_apicid = 0, nodes;
struct mem_controller ctrl[8];
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx);
winbond_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
console_init();
// dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x200, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE);
/* Halt if there was a built in self test failure */
report_bist_failure(bist);
setup_khepri_resource_map();
#if 0
dump_pci_device(PCI_DEV(0, 0x18, 0));
dump_pci_device(PCI_DEV(0, 0x19, 0));
#endif
needs_reset = setup_coherent_ht_domain();
wait_all_core0_started();
#if CONFIG_LOGICAL_CPUS
// It is said that we should start core1 after all core0 launched
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
needs_reset |= ht_setup_chains_x();
if (needs_reset) {
print_info("ht reset -\n");
soft_reset();
}
allow_all_aps_stop(bsp_apicid);
nodes = get_nodes();
//It's the time to set ctrl now;
fill_mem_ctrl(nodes, ctrl, spd_addr);
enable_smbus();
memreset_setup();
sdram_initialize(nodes, ctrl);
#if 0
dump_pci_devices();
#endif
post_cache_as_ram();
}
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
static const uint16_t spd_addr[] = {
// Node 0
DIMM0, DIMM2, 0, 0,
DIMM1, DIMM3, 0, 0,
// Node 1
DIMM4, DIMM6, 0, 0,
DIMM5, DIMM7, 0, 0,
};
unsigned bsp_apicid = 0;
int needs_reset = 0;
struct sys_info *sysinfo = &sysinfo_car;
ite_enable_serial(SERIAL_DEV, CONFIG_TTYS0_BASE);
it8712f_kill_watchdog();
it8712f_enable_3vsbsw();
console_init();
enable_rom_decode();
printk(BIOS_INFO, "now booting... \n");
if (bist == 0)
bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo);
/* Halt if there was a built in self test failure. */
report_bist_failure(bist);
setup_default_resource_map();
setup_coherent_ht_domain();
wait_all_core0_started();
printk(BIOS_INFO, "now booting... All core 0 started\n");
#if CONFIG_LOGICAL_CPUS
/* It is said that we should start core1 after all core0 launched. */
start_other_cores();
wait_all_other_cores_started(bsp_apicid);
#endif
init_timer();
ht_setup_chains_x(sysinfo); /* Init sblnk and sbbusn, nodes, sbdn. */
needs_reset = optimize_link_coherent_ht();
print_debug_hex8(needs_reset);
needs_reset |= optimize_link_incoherent_ht(sysinfo);
print_debug_hex8(needs_reset);
needs_reset |= k8t890_early_setup_ht();
print_debug_hex8(needs_reset);
vt8237_early_network_init(NULL);
vt8237_early_spi_init();
if (needs_reset) {
printk(BIOS_DEBUG, "ht reset -\n");
soft_reset();
printk(BIOS_DEBUG, "FAILED!\n");
}
/* the HT settings needs to be OK, because link freq chnage may cause HT disconnect */
/* allow LDT STOP asserts */
vt8237_sb_enable_fid_vid();
enable_fid_change();
print_debug("after enable_fid_change\n");
init_fidvid_bsp(bsp_apicid);
/* Stop the APs so we can start them later in init. */
allow_all_aps_stop(bsp_apicid);
/* It's the time to set ctrl now. */
fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);
enable_smbus();
sdram_initialize(sysinfo->nodes, sysinfo->ctrl, sysinfo);
post_cache_as_ram();
}
