void __init plat_time_init(void)
{
unsigned int est_freq;
/* Set Data mode - binary. */
CMOS_WRITE(CMOS_READ(RTC_CONTROL) | RTC_DM_BINARY, RTC_CONTROL);
est_freq = estimate_cpu_frequency();
printk("CPU frequency %d.%02d MHz\n", est_freq/1000000,
(est_freq%1000000)*100/1000000);
cpu_khz = est_freq / 1000;
mips_scroll_message();
#ifdef CONFIG_I8253 /* Only Malta has a PIT */
setup_pit_timer();
#endif
#ifdef CONFIG_CSRC_GIC
gic_clocksource_init();
#endif
plat_perf_setup();
}
void __init plat_time_init(void)
{
u32 start, end;
int i = HZ / 10;
setup_pit_timer();
gt641xx_set_base_clock(GT641XX_BASE_CLOCK);
/*
* MIPS counter frequency is measured during a 100msec interval
* using GT64111 timer0.
*/
while (!gt641xx_timer0_state())
;
start = read_c0_count();
while (i--)
while (!gt641xx_timer0_state())
;
end = read_c0_count();
mips_hpt_frequency = (end - start) * 10;
printk(KERN_INFO "MIPS counter frequency %dHz\n", mips_hpt_frequency);
}
void __init plat_time_init(void)
{
unsigned int prid = read_c0_prid() & (PRID_COMP_MASK | PRID_IMP_MASK);
unsigned int freq;
init_rtc();
estimate_frequencies();
freq = mips_hpt_frequency;
if ((prid != (PRID_COMP_MIPS | PRID_IMP_20KC)) &&
(prid != (PRID_COMP_MIPS | PRID_IMP_25KF)))
freq *= 2;
freq = freqround(freq, 5000);
printk("CPU frequency %d.%02d MHz\n", freq/1000000,
(freq%1000000)*100/1000000);
mips_scroll_message();
#ifdef CONFIG_I8253
/* Only Malta has a PIT. */
setup_pit_timer();
#endif
#ifdef CONFIG_MIPS_GIC
if (gic_present) {
freq = freqround(gic_frequency, 5000);
printk("GIC frequency %d.%02d MHz\n", freq/1000000,
(freq%1000000)*100/1000000);
#ifdef CONFIG_CLKSRC_MIPS_GIC
gic_clocksource_init(gic_frequency);
#endif
}
#endif
}
static int timer_resume(struct sys_device *dev)
{
unsigned long flags;
unsigned long sec;
unsigned long sleep_length;
#ifdef CONFIG_HPET_TIMER
if (is_hpet_enabled())
hpet_reenable();
#endif
setup_pit_timer();
sec = get_cmos_time() + clock_cmos_diff;
sleep_length = (get_cmos_time() - sleep_start) * HZ;
write_seqlock_irqsave(&xtime_lock, flags);
xtime.tv_sec = sec;
xtime.tv_nsec = 0;
jiffies_64 += sleep_length;
wall_jiffies += sleep_length;
write_sequnlock_irqrestore(&xtime_lock, flags);
if (last_timer->resume)
last_timer->resume();
cur_timer = last_timer;
last_timer = NULL;
touch_softlockup_watchdog();
return 0;
}
/*
* Here we need to calibrate the cycle counter to at least be close.
*/
void __init plat_time_init(void)
{
unsigned long r4k_ticks[3];
unsigned long r4k_tick;
/*
* Figure out the r4k offset, the algorithm is very simple and works in
* _all_ cases as long as the 8254 counter register itself works ok (as
* an interrupt driving timer it does not because of bug, this is why
* we are using the onchip r4k counter/compare register to serve this
* purpose, but for r4k_offset calculation it will work ok for us).
* There are other very complicated ways of performing this calculation
* but this one works just fine so I am not going to futz around. ;-)
*/
printk(KERN_INFO "Calibrating system timer... ");
dosample(); /* Prime cache. */
dosample(); /* Prime cache. */
/* Zero is NOT an option. */
do {
r4k_ticks[0] = dosample();
} while (!r4k_ticks[0]);
do {
r4k_ticks[1] = dosample();
} while (!r4k_ticks[1]);
if (r4k_ticks[0] != r4k_ticks[1]) {
printk("warning: timer counts differ, retrying... ");
r4k_ticks[2] = dosample();
if (r4k_ticks[2] == r4k_ticks[0]
|| r4k_ticks[2] == r4k_ticks[1])
r4k_tick = r4k_ticks[2];
else {
printk("disagreement, using average... ");
r4k_tick = (r4k_ticks[0] + r4k_ticks[1]
+ r4k_ticks[2]) / 3;
}
} else
r4k_tick = r4k_ticks[0];
printk("%d [%d.%04d MHz CPU]\n", (int) r4k_tick,
(int) (r4k_tick / (500000 / HZ)),
(int) (r4k_tick % (500000 / HZ)));
mips_hpt_frequency = r4k_tick * HZ;
switch (sni_brd_type) {
case SNI_BRD_10:
case SNI_BRD_10NEW:
case SNI_BRD_TOWER_OASIC:
case SNI_BRD_MINITOWER:
sni_a20r_timer_setup();
break;
}
setup_pit_timer();
}
