int platform_init() { unsigned i; TIM_InitTypeDef tim; TIM_TypeDef* base; // System configuration platform_config_scu(); // PIO setup for( i = 0; i < 10; i ++ ) GPIO_DeInit( ( GPIO_TypeDef* )port_data[ i ] ); // UART setup (only STR9_UART is used in this example) platform_uart_setup( 0, 115200, 8, PLATFORM_UART_PARITY_NONE, PLATFORM_UART_STOPBITS_1 ); // Initialize timers for( i = 0; i < 4; i ++ ) { base = ( TIM_TypeDef* )timer_data[ i ]; TIM_DeInit( base ); TIM_StructInit( &tim ); tim.TIM_Clock_Source = TIM_CLK_APB; tim.TIM_Prescaler = 255; TIM_Init( base, &tim ); TIM_CounterCmd( base, TIM_START ); } // Set the send/recv functions std_set_send_func( uart_send ); std_set_get_func( uart_recv ); return PLATFORM_OK; }
int platform_init() { cmn_platform_init(); std_set_send_func(ssend); std_set_get_func(srecv); return PLATFORM_OK; }
void cmn_platform_init() { // Set the send/recv functions std_set_send_func( uart_send ); std_set_get_func( uart_recv ); #ifdef BUILD_XMODEM // Initialize XMODEM xmodem_init( xmodem_send, xmodem_recv ); #endif #ifdef BUILD_TERM // Initialize terminal term_init( TERM_LINES, TERM_COLS, term_out, term_in, term_translate ); #endif }
void cmn_platform_init() { #ifdef BUILD_INT_HANDLERS platform_int_init(); #endif #ifdef BUILD_SERMUX unsigned i; unsigned bufsizes[] = SERMUX_BUFFER_SIZES; // Setup the serial multiplexer platform_uart_setup( SERMUX_PHYS_ID, SERMUX_PHYS_SPEED, 8, PLATFORM_UART_PARITY_NONE, PLATFORM_UART_STOPBITS_1 ); platform_uart_set_flow_control( SERMUX_PHYS_ID, SERMUX_FLOW_TYPE ); cmn_uart_setup_sermux(); // Set buffers for all virtual UARTs for( i = 0; i < sizeof( bufsizes ) / sizeof( unsigned ); i ++ ) platform_uart_set_buffer( i + SERMUX_SERVICE_ID_FIRST, bufsizes[ i ] ); #endif // #ifdef BUILD_SERMUX #if defined( CON_UART_ID ) && CON_UART_ID < SERMUX_SERVICE_ID_FIRST // Setup console UART platform_uart_setup( CON_UART_ID, CON_UART_SPEED, 8, PLATFORM_UART_PARITY_NONE, PLATFORM_UART_STOPBITS_1 ); platform_uart_set_flow_control( CON_UART_ID, CON_FLOW_TYPE ); platform_uart_set_buffer( CON_UART_ID, CON_BUF_SIZE ); #endif // #if defined( CON_UART_ID ) && CON_UART_ID < SERMUX_SERVICE_ID_FIRST #ifndef BUILD_WEB_SERVER // Set the send/recv functions std_set_send_func( uart_send ); std_set_get_func( uart_recv ); #endif #ifdef BUILD_XMODEM // Initialize XMODEM xmodem_init( xmodem_send, xmodem_recv ); #endif #ifdef BUILD_TERM // Initialize terminal term_init( TERM_LINES, TERM_COLS, term_out, term_in, term_translate ); #endif }
int platform_init() { // Initialize CPU lpc288x_init(); // Initialize UART uart_init( 115200, 8, PLATFORM_UART_PARITY_NONE, PLATFORM_UART_STOPBITS_1 ); // Initialize timers T0CTRL = 0; T1CTRL = 0; INT_REQ5 = ( 1 << 28 ) | ( 1 << 27 ) | ( 1 << 26 ) | ( 1 << 16 ) | 0x1; INT_REQ6 = ( 1 << 28 ) | ( 1 << 27 ) | ( 1 << 26 ) | ( 1 << 16 ) | 0x1; // Set the send/recv functions std_set_send_func( uart_send ); std_set_get_func( uart_recv ); return PLATFORM_OK; }
int platform_init() { int i; unsigned int mode = AT91C_US_USMODE_NORMAL | AT91C_US_CLKS_CLOCK | AT91C_US_CHRL_8_BITS | AT91C_US_PAR_NONE | AT91C_US_NBSTOP_1_BIT | AT91C_US_CHMODE_NORMAL; // Enable the peripherals we use in the PMC PMC_EnablePeripheral(AT91C_ID_US0); PMC_EnablePeripheral(AT91C_ID_US1); PMC_EnablePeripheral(AT91C_ID_PIOA); PMC_EnablePeripheral(AT91C_ID_PIOB); PMC_EnablePeripheral(AT91C_ID_TC0); PMC_EnablePeripheral(AT91C_ID_TC1); PMC_EnablePeripheral(AT91C_ID_TC2); // Configure pins PIO_Configure(platform_uart_pins[ 0 ], PIO_LISTSIZE(platform_uart_pins[ 0 ])); // Configure the USART in the desired mode @115200 bauds USART_Configure(AT91C_BASE_US0, mode, 115200, BOARD_MCK); // Enable receiver & transmitter USART_SetTransmitterEnabled(AT91C_BASE_US0, 1); USART_SetReceiverEnabled(AT91C_BASE_US0, 1); // Configure the timers AT91C_BASE_TCB->TCB_BMR = 7; for( i = 0; i < 3; i ++ ) TC_Configure( ( AT91S_TC* )timer_base[ i ], AT91C_TC_CLKS_TIMER_DIV5_CLOCK | AT91C_TC_WAVE ); // Set the send/recv functions std_set_send_func( uart_send ); std_set_get_func( uart_recv ); return PLATFORM_OK; }
int platform_init() { if( memory_start_address == NULL ) { hostif_putstr( "platform_init(): mmap failed\n" ); return PLATFORM_ERR; } // Set the std input/output functions // Set the send/recv functions std_set_send_func( scr_write ); std_set_get_func( kb_read ); // Set term functions #ifdef BUILD_TERM term_init( TERM_LINES, TERM_COLS, i386_term_out, i386_term_in, i386_term_translate ); #endif term_clrscr(); term_gotoxy( 1, 1 ); // All done return PLATFORM_OK; }
int platform_init() { // Set the clocking to run directly from the crystal. SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN | SYSCTL_XTAL_8MHZ); // Setup PIO pios_init(); // Setup SSIs spis_init(); // Setup UARTs uarts_init(); // Setup timers timers_init(); // Set the send/recv functions std_set_send_func( uart_send ); std_set_get_func( uart_recv ); // All done return PLATFORM_OK; }