static void nano_standby(int instadby)
{
if (instadby) {
if (nano_powerup) {
nano_gpio_ctrl("swl_n20_shdn", 0);
nano_gpio_ctrl("swl_n20_vdd_en", 0);
nano_gpio_ctrl("swl_n20_vcc_en", 0);
nano_suspend = 1;
}
} else {
if (nano_suspend) {
nano_gpio_ctrl("swl_n20_vcc_en", 1);
udelay(100);
nano_gpio_ctrl("swl_n20_shdn", 1);
udelay(50);
nano_gpio_ctrl("swl_n20_vdd_en", 1);
sw_mmc_rescan_card(3, 1);
nano_suspend = 0;
}
}
}
/* Customer function to control hw specific wlan gpios */
void
dhd_customer_gpio_wlan_ctrl(int onoff)
{
#if defined CUSTOMER_ALLWINNER && defined CONFIG_SW_MMC_POWER_CONTROL
unsigned int mod_sel = mmc_pm_get_mod_type();
#endif
switch (onoff) {
case WLAN_RESET_OFF:
WL_TRACE(("%s: call customer specific GPIO to insert WLAN RESET\n",
__FUNCTION__));
/* winner's power control */
#if defined CUSTOMER_ALLWINNER && defined CONFIG_SW_MMC_POWER_CONTROL
switch (mod_sel)
{
case 2: /* usi bm01a */
mmc_pm_gpio_ctrl("usi_bm01a_wl_rst", 0);
mmc_pm_gpio_ctrl("usi_bm01a_wl_regon", 0);
break;
case 5: /* swb b23 */
mmc_pm_gpio_ctrl("swbb23_wl_shdn", 0);
break;
default:
printk("[bcm4329]: no wifi module matched !!\n");
}
#endif
#ifdef CUSTOMER_HW
bcm_wlan_power_off(2);
#endif /* CUSTOMER_HW */
#ifdef CUSTOMER_HW2
wifi_set_power(0, 0);
#endif
WL_ERROR(("=========== WLAN placed in RESET ========\n"));
break;
case WLAN_RESET_ON:
WL_TRACE(("%s: callc customer specific GPIO to remove WLAN RESET\n",
__FUNCTION__));
/* winner's power control */
#if defined CUSTOMER_ALLWINNER && defined CONFIG_SW_MMC_POWER_CONTROL
switch (mod_sel)
{
case 2: /* usi bm01a */
mmc_pm_gpio_ctrl("usi_bm01a_wl_regon", 1);
mmc_pm_gpio_ctrl("usi_bm01a_wl_rst", 1);
break;
case 5: /* swb b23 */
mmc_pm_gpio_ctrl("swbb23_wl_shdn", 1);
break;
default:
printk("[bcm4329]: no wifi module matched !!\n");
}
#endif
#ifdef CUSTOMER_HW
bcm_wlan_power_on(2);
#endif /* CUSTOMER_HW */
#ifdef CUSTOMER_HW2
wifi_set_power(1, 0);
#endif
WL_ERROR(("=========== WLAN going back to live ========\n"));
OSL_DELAY(10000);
break;
case WLAN_POWER_OFF:
WL_TRACE(("%s: call customer specific GPIO to turn off WL_REG_ON\n",
__FUNCTION__));
/* winner's power control */
#if defined CUSTOMER_ALLWINNER && defined CONFIG_SW_MMC_POWER_CONTROL
switch (mod_sel)
{
case 2: /* usi bm01a */
mmc_pm_gpio_ctrl("usi_bm01a_wl_rst", 0);
mmc_pm_gpio_ctrl("usi_bm01a_wl_regon", 0);
break;
case 5: /* swb b23 */
mmc_pm_gpio_ctrl("swbb23_wl_shdn", 0);
break;
default:
printk("[bcm4329]: no wifi module matched !!\n");
}
sw_mmc_rescan_card(3, 0);
#endif
#ifdef CUSTOMER_HW
bcm_wlan_power_off(1);
#endif /* CUSTOMER_HW */
break;
case WLAN_POWER_ON:
WL_TRACE(("%s: call customer specific GPIO to turn on WL_REG_ON\n",
__FUNCTION__));
/* winner's power control */
#if defined CUSTOMER_ALLWINNER && defined CONFIG_SW_MMC_POWER_CONTROL
switch (mod_sel)
{
case 2: /* usi bm01a */
mmc_pm_gpio_ctrl("usi_bm01a_wl_regon", 1);
mmc_pm_gpio_ctrl("usi_bm01a_wl_rst", 1);
break;
case 5: /* swb b23 */
mmc_pm_gpio_ctrl("swbb23_wl_shdn", 1);
break;
default:
printk("[bcm4329]: no wifi module matched !!\n");
}
#endif
#ifdef CUSTOMER_HW
bcm_wlan_power_on(1);
#endif /* CUSTOMER_HW */
/* Lets customer power to get stable */
OSL_DELAY(200);
#if defined CUSTOMER_ALLWINNER && defined CONFIG_SW_MMC_POWER_CONTROL
sw_mmc_rescan_card(3, 1);
#endif
break;
}
}
/* Customer function to control hw specific wlan gpios */
void
dhd_customer_gpio_wlan_ctrl(int onoff)
{
#if defined CUSTOMER_ALLWINNER && defined CONFIG_SW_MMC_POWER_CONTROL
unsigned int mod_sel = mmc_pm_get_mod_type();
if (mod_sel != 6) {
printk("Config Error: not for huawei mw269x sdio wifi module\n");
}
#endif
switch (onoff) {
case WLAN_RESET_OFF:
WL_TRACE(("%s: call customer specific GPIO to insert WLAN RESET\n",
__FUNCTION__));
#if defined CUSTOMER_ALLWINNER && defined CONFIG_SW_MMC_POWER_CONTROL
mmc_pm_gpio_ctrl("hw_mw269x_wl_enb", 0);
#endif
#ifdef CUSTOMER_HW
bcm_wlan_power_off(2);
#endif /* CUSTOMER_HW */
#ifdef CUSTOMER_HW2
wifi_set_power(0, 0);
#endif
WL_ERROR(("=========== WLAN placed in RESET ========\n"));
break;
case WLAN_RESET_ON:
WL_TRACE(("%s: callc customer specific GPIO to remove WLAN RESET\n",
__FUNCTION__));
#if defined CUSTOMER_ALLWINNER && defined CONFIG_SW_MMC_POWER_CONTROL
mmc_pm_gpio_ctrl("hw_mw269x_wl_enb", 1);
#endif
#ifdef CUSTOMER_HW
bcm_wlan_power_on(2);
#endif /* CUSTOMER_HW */
#ifdef CUSTOMER_HW2
wifi_set_power(1, 0);
#endif
WL_ERROR(("=========== WLAN going back to live ========\n"));
OSL_DELAY(10000);
break;
case WLAN_POWER_OFF:
WL_TRACE(("%s: call customer specific GPIO to turn off WL_REG_ON\n",
__FUNCTION__));
#if defined CUSTOMER_ALLWINNER && defined CONFIG_SW_MMC_POWER_CONTROL
mmc_pm_gpio_ctrl("hw_mw269x_wl_enb", 0);
sw_mmc_rescan_card(3, 0);
#endif
#ifdef CUSTOMER_HW
bcm_wlan_power_off(1);
#endif /* CUSTOMER_HW */
break;
case WLAN_POWER_ON:
WL_TRACE(("%s: call customer specific GPIO to turn on WL_REG_ON\n",
__FUNCTION__));
#if defined CUSTOMER_ALLWINNER && defined CONFIG_SW_MMC_POWER_CONTROL
mmc_pm_gpio_ctrl("hw_mw269x_wl_enb", 1);
#endif
#ifdef CUSTOMER_HW
bcm_wlan_power_on(1);
#endif /* CUSTOMER_HW */
/* Lets customer power to get stable */
OSL_DELAY(200);
#if defined CUSTOMER_ALLWINNER && defined CONFIG_SW_MMC_POWER_CONTROL
sw_mmc_rescan_card(3, 1);
#endif /* CUSTOMER_HW */
break;
}
}
