static void
leonuart_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
unsigned int cr;
unsigned long flags;
unsigned int baud, quot;
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
if (baud == 0) {
panic("invalid baudrate %i\n", port->uartclk / 16);
}
quot = (uart_get_divisor(port, baud)) * 2; //uart_get_divisor calc a *16 uart freq, leon is *8
cr = UART_GET_CTRL(port);
cr &= ~(LEON_REG_UART_CTRL_PE | LEON_REG_UART_CTRL_PS);
if (termios->c_cflag & PARENB) {
cr |= LEON_REG_UART_CTRL_PE;
if ((termios->c_cflag & PARODD))
cr |= LEON_REG_UART_CTRL_PS;
}
/*
* Enable flow control.
*/
if (termios->c_cflag & CRTSCTS) {
cr |= LEON_REG_UART_CTRL_FL;
}
spin_lock_irqsave(&port->lock, flags);
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
port->read_status_mask = LEON_REG_UART_STATUS_OE;
if (termios->c_iflag & INPCK)
port->read_status_mask |=
LEON_REG_UART_STATUS_FE | LEON_REG_UART_STATUS_PE;
/*
* Characters to ignore
*/
port->ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |=
LEON_REG_UART_STATUS_FE | LEON_REG_UART_STATUS_PE;
/*
* Ignore all characters if CREAD is not set.
*/
if ((termios->c_cflag & CREAD) == 0) {
port->ignore_status_mask |= UART_DUMMY_RSR_RX;
}
/* Set baud rate */
quot -= 1;
UART_PUT_SCAL(port, quot);
UART_PUT_CTRL(port, cr);
spin_unlock_irqrestore(&port->lock, flags);
}
static void cpm_uart_set_termios(struct uart_port *port,
struct termios *termios, struct termios *old)
{
int baud;
unsigned long flags;
u16 cval, scval, prev_mode;
int bits, sbits;
struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
volatile smc_t *smcp = pinfo->smcp;
volatile scc_t *sccp = pinfo->sccp;
pr_debug("CPM uart[%d]:set_termios\n", port->line);
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
/* Character length programmed into the mode register is the
* sum of: 1 start bit, number of data bits, 0 or 1 parity bit,
* 1 or 2 stop bits, minus 1.
* The value 'bits' counts this for us.
*/
cval = 0;
scval = 0;
/* byte size */
switch (termios->c_cflag & CSIZE) {
case CS5:
bits = 5;
break;
case CS6:
bits = 6;
break;
case CS7:
bits = 7;
break;
case CS8:
bits = 8;
break;
/* Never happens, but GCC is too dumb to figure it out */
default:
bits = 8;
break;
}
sbits = bits - 5;
if (termios->c_cflag & CSTOPB) {
cval |= SMCMR_SL; /* Two stops */
scval |= SCU_PSMR_SL;
bits++;
}
if (termios->c_cflag & PARENB) {
cval |= SMCMR_PEN;
scval |= SCU_PSMR_PEN;
bits++;
if (!(termios->c_cflag & PARODD)) {
cval |= SMCMR_PM_EVEN;
scval |= (SCU_PSMR_REVP | SCU_PSMR_TEVP);
}
}
/*
* Set up parity check flag
*/
#define RELEVANT_IFLAG(iflag) (iflag & (IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK))
port->read_status_mask = (BD_SC_EMPTY | BD_SC_OV);
if (termios->c_iflag & INPCK)
port->read_status_mask |= BD_SC_FR | BD_SC_PR;
if ((termios->c_iflag & BRKINT) || (termios->c_iflag & PARMRK))
port->read_status_mask |= BD_SC_BR;
/*
* Characters to ignore
*/
port->ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= BD_SC_PR | BD_SC_FR;
if (termios->c_iflag & IGNBRK) {
port->ignore_status_mask |= BD_SC_BR;
/*
* If we're ignore parity and break indicators, ignore
* overruns too. (For real raw support).
*/
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= BD_SC_OV;
}
/*
* !!! ignore all characters if CREAD is not set
*/
if ((termios->c_cflag & CREAD) == 0)
port->read_status_mask &= ~BD_SC_EMPTY;
spin_lock_irqsave(&port->lock, flags);
/* Start bit has not been added (so don't, because we would just
* subtract it later), and we need to add one for the number of
* stops bits (there is always at least one).
*/
bits++;
if (IS_SMC(pinfo)) {
/* Set the mode register. We want to keep a copy of the
* enables, because we want to put them back if they were
* present.
*/
prev_mode = smcp->smc_smcmr;
smcp->smc_smcmr = smcr_mk_clen(bits) | cval | SMCMR_SM_UART;
smcp->smc_smcmr |= (prev_mode & (SMCMR_REN | SMCMR_TEN));
} else {
sccp->scc_psmr = (sbits << 12) | scval;
}
cpm_set_brg(pinfo->brg - 1, baud);
spin_unlock_irqrestore(&port->lock, flags);
}
/*
* Change the port parameters
*/
static void at91_set_termios(struct uart_port *port, struct termios * termios, struct termios * old)
{
unsigned long flags;
unsigned int mode, imr, quot, baud;
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
quot = uart_get_divisor(port, baud);
/* Get current mode register */
mode = UART_GET_MR(port) & ~(AT91_US_CHRL | AT91_US_NBSTOP | AT91_US_PAR);
/* byte size */
switch (termios->c_cflag & CSIZE) {
case CS5:
mode |= AT91_US_CHRL_5;
break;
case CS6:
mode |= AT91_US_CHRL_6;
break;
case CS7:
mode |= AT91_US_CHRL_7;
break;
default:
mode |= AT91_US_CHRL_8;
break;
}
/* stop bits */
if (termios->c_cflag & CSTOPB)
mode |= AT91_US_NBSTOP_2;
/* parity */
if (termios->c_cflag & PARENB) {
if (termios->c_cflag & CMSPAR) { /* Mark or Space parity */
if (termios->c_cflag & PARODD)
mode |= AT91_US_PAR_MARK;
else
mode |= AT91_US_PAR_SPACE;
}
else if (termios->c_cflag & PARODD)
mode |= AT91_US_PAR_ODD;
else
mode |= AT91_US_PAR_EVEN;
}
else
mode |= AT91_US_PAR_NONE;
spin_lock_irqsave(&port->lock, flags);
port->read_status_mask |= AT91_US_OVRE;
if (termios->c_iflag & INPCK)
port->read_status_mask |= AT91_US_FRAME | AT91_US_PARE;
if (termios->c_iflag & (BRKINT | PARMRK))
port->read_status_mask |= AT91_US_RXBRK;
/*
* Characters to ignore
*/
port->ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= (AT91_US_FRAME | AT91_US_PARE);
if (termios->c_iflag & IGNBRK) {
port->ignore_status_mask |= AT91_US_RXBRK;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= AT91_US_OVRE;
}
// TODO: Ignore all characters if CREAD is set.
/* update the per-port timeout */
uart_update_timeout(port, termios->c_cflag, baud);
/* disable interrupts and drain transmitter */
imr = UART_GET_IMR(port); /* get interrupt mask */
UART_PUT_IDR(port, -1); /* disable all interrupts */
while (!(UART_GET_CSR(port) & AT91_US_TXEMPTY)) { barrier(); }
/* disable receiver and transmitter */
UART_PUT_CR(port, AT91_US_TXDIS | AT91_US_RXDIS);
/* set the parity, stop bits and data size */
UART_PUT_MR(port, mode);
/* set the baud rate */
UART_PUT_BRGR(port, quot);
UART_PUT_CR(port, AT91_US_RSTSTA | AT91_US_RSTRX);
UART_PUT_CR(port, AT91_US_TXEN | AT91_US_RXEN);
/* restore interrupts */
UART_PUT_IER(port, imr);
/* CTS flow-control and modem-status interrupts */
if (UART_ENABLE_MS(port, termios->c_cflag))
port->ops->enable_ms(port);
spin_unlock_irqrestore(&port->lock, flags);
}
static void msm_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
unsigned long flags;
unsigned int baud, mr;
spin_lock_irqsave(&port->lock, flags);
/* calculate and set baud rate */
baud = uart_get_baud_rate(port, termios, old, 300, 115200);
baud = msm_set_baud_rate(port, baud);
if (tty_termios_baud_rate(termios))
tty_termios_encode_baud_rate(termios, baud, baud);
/* calculate parity */
mr = msm_read(port, UART_MR2);
mr &= ~UART_MR2_PARITY_MODE;
if (termios->c_cflag & PARENB) {
if (termios->c_cflag & PARODD)
mr |= UART_MR2_PARITY_MODE_ODD;
else if (termios->c_cflag & CMSPAR)
mr |= UART_MR2_PARITY_MODE_SPACE;
else
mr |= UART_MR2_PARITY_MODE_EVEN;
}
/* calculate bits per char */
mr &= ~UART_MR2_BITS_PER_CHAR;
switch (termios->c_cflag & CSIZE) {
case CS5:
mr |= UART_MR2_BITS_PER_CHAR_5;
break;
case CS6:
mr |= UART_MR2_BITS_PER_CHAR_6;
break;
case CS7:
mr |= UART_MR2_BITS_PER_CHAR_7;
break;
case CS8:
default:
mr |= UART_MR2_BITS_PER_CHAR_8;
break;
}
/* calculate stop bits */
mr &= ~(UART_MR2_STOP_BIT_LEN_ONE | UART_MR2_STOP_BIT_LEN_TWO);
if (termios->c_cflag & CSTOPB)
mr |= UART_MR2_STOP_BIT_LEN_TWO;
else
mr |= UART_MR2_STOP_BIT_LEN_ONE;
/* set parity, bits per char, and stop bit */
msm_write(port, mr, UART_MR2);
/* calculate and set hardware flow control */
mr = msm_read(port, UART_MR1);
mr &= ~(UART_MR1_CTS_CTL | UART_MR1_RX_RDY_CTL);
if (termios->c_cflag & CRTSCTS) {
mr |= UART_MR1_CTS_CTL;
mr |= UART_MR1_RX_RDY_CTL;
}
msm_write(port, mr, UART_MR1);
/* Configure status bits to ignore based on termio flags. */
port->read_status_mask = 0;
if (termios->c_iflag & INPCK)
port->read_status_mask |= UART_SR_PAR_FRAME_ERR;
if (termios->c_iflag & (BRKINT | PARMRK))
port->read_status_mask |= UART_SR_RX_BREAK;
uart_update_timeout(port, termios->c_cflag, baud);
spin_unlock_irqrestore(&port->lock, flags);
}
static void lh7a40xuart_set_termios (struct uart_port* port,
struct termios* termios,
struct termios* old)
{
unsigned int con;
unsigned int inten;
unsigned int fcon;
unsigned long flags;
unsigned int baud;
unsigned int quot;
baud = uart_get_baud_rate (port, termios, old, 8, port->uartclk/16);
quot = uart_get_divisor (port, baud); /* -1 performed elsewhere */
switch (termios->c_cflag & CSIZE) {
case CS5:
fcon = WLEN_5;
break;
case CS6:
fcon = WLEN_6;
break;
case CS7:
fcon = WLEN_7;
break;
case CS8:
default:
fcon = WLEN_8;
break;
}
if (termios->c_cflag & CSTOPB)
fcon |= STP2;
if (termios->c_cflag & PARENB) {
fcon |= PEN;
if (!(termios->c_cflag & PARODD))
fcon |= EPS;
}
if (port->fifosize > 1)
fcon |= FEN;
spin_lock_irqsave (&port->lock, flags);
uart_update_timeout (port, termios->c_cflag, baud);
port->read_status_mask = RxOverrunError;
if (termios->c_iflag & INPCK)
port->read_status_mask |= RxFramingError | RxParityError;
if (termios->c_iflag & (BRKINT | PARMRK))
port->read_status_mask |= RxBreak;
/* Figure mask for status we ignore */
port->ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= RxFramingError | RxParityError;
if (termios->c_iflag & IGNBRK) {
port->ignore_status_mask |= RxBreak;
/* Ignore overrun when ignorning parity */
/* *** FIXME: is this in the right place? */
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= RxOverrunError;
}
/* Ignore all receive errors when receive disabled */
if ((termios->c_cflag & CREAD) == 0)
port->ignore_status_mask |= RxError;
con = UR (port, UART_R_CON);
inten = (UR (port, UART_R_INTEN) & ~ModemInt);
if (UART_ENABLE_MS (port, termios->c_cflag))
inten |= ModemInt;
BIT_CLR (port, UART_R_CON, UARTEN); /* Disable UART */
UR (port, UART_R_INTEN) = 0; /* Disable interrupts */
UR (port, UART_R_BRCON) = quot - 1; /* Set baud rate divisor */
UR (port, UART_R_FCON) = fcon; /* Set FIFO and frame ctrl */
UR (port, UART_R_INTEN) = inten; /* Enable interrupts */
UR (port, UART_R_CON) = con; /* Restore UART mode */
spin_unlock_irqrestore(&port->lock, flags);
}
static void tegra_set_termios(struct uart_port *u, struct ktermios *termios,
struct ktermios *oldtermios)
{
struct tegra_uart_port *t;
unsigned int baud;
unsigned long flags;
unsigned int lcr;
unsigned int c_cflag = termios->c_cflag;
unsigned char mcr;
t = container_of(u, struct tegra_uart_port, uport);
dev_vdbg(t->uport.dev, "+tegra_set_termios\n");
spin_lock_irqsave(&u->lock, flags);
/* Changing configuration, it is safe to stop any rx now */
if (t->rts_active)
set_rts(t, false);
/* Parity */
lcr = t->lcr_shadow;
lcr &= ~UART_LCR_PARITY;
if (PARENB == (c_cflag & PARENB)) {
if (CMSPAR == (c_cflag & CMSPAR)) {
/* FIXME What is space parity? */
/* data |= SPACE_PARITY; */
} else if (c_cflag & PARODD) {
lcr |= UART_LCR_PARITY;
lcr &= ~UART_LCR_EPAR;
lcr &= ~UART_LCR_SPAR;
} else {
lcr |= UART_LCR_PARITY;
lcr |= UART_LCR_EPAR;
lcr &= ~UART_LCR_SPAR;
}
}
lcr &= ~UART_LCR_WLEN8;
switch (c_cflag & CSIZE) {
case CS5:
lcr |= UART_LCR_WLEN5;
break;
case CS6:
lcr |= UART_LCR_WLEN6;
break;
case CS7:
lcr |= UART_LCR_WLEN7;
break;
default:
lcr |= UART_LCR_WLEN8;
break;
}
/* Stop bits */
if (termios->c_cflag & CSTOPB)
lcr |= UART_LCR_STOP;
else
lcr &= ~UART_LCR_STOP;
uart_writeb(t, lcr, UART_LCR);
t->lcr_shadow = lcr;
/* Baud rate. */
baud = uart_get_baud_rate(u, termios, oldtermios, 200, 4000000);
tegra_set_baudrate(t, baud);
/* Flow control */
if (termios->c_cflag & CRTSCTS) {
mcr = t->mcr_shadow;
mcr |= UART_MCR_CTS_EN;
mcr &= ~UART_MCR_RTS_EN;
t->mcr_shadow = mcr;
uart_writeb(t, mcr, UART_MCR);
t->use_cts_control = true;
/* if top layer has asked to set rts active then do so here */
if (t->rts_active)
set_rts(t, true);
} else {
mcr = t->mcr_shadow;
mcr &= ~UART_MCR_CTS_EN;
mcr &= ~UART_MCR_RTS_EN;
t->mcr_shadow = mcr;
uart_writeb(t, mcr, UART_MCR);
t->use_cts_control = false;
}
/* update the port timeout based on new settings */
uart_update_timeout(u, termios->c_cflag, baud);
spin_unlock_irqrestore(&u->lock, flags);
dev_vdbg(t->uport.dev, "-tegra_set_termios\n");
return;
}
static void s3c24xx_serial_set_termios(struct uart_port *port,
struct termios *termios,
struct termios *old)
{
struct s3c2410_uartcfg *cfg = s3c24xx_port_to_cfg(port);
struct s3c24xx_uart_port *ourport = to_ourport(port);
struct s3c24xx_uart_clksrc *clksrc;
struct clk *clk;
unsigned long flags;
unsigned int baud, quot;
unsigned int ulcon;
unsigned int umcon;
/*
* We don't support modem control lines.
*/
termios->c_cflag &= ~(HUPCL | CMSPAR);
termios->c_cflag |= CLOCAL;
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 0, 115200*8);
if (baud == 38400 && (port->flags & UPF_SPD_MASK) == UPF_SPD_CUST)
quot = port->custom_divisor;
else
quot = s3c24xx_serial_getclk(port, &clksrc, &clk, baud);
/* check to see if we need to change clock source */
if (ourport->clksrc != clksrc || ourport->baudclk != clk) {
s3c24xx_serial_setsource(port, clksrc);
if (ourport->baudclk != NULL && !IS_ERR(ourport->baudclk)) {
clk_disable(ourport->baudclk);
clk_unuse(ourport->baudclk);
ourport->baudclk = NULL;
}
clk_use(clk);
clk_enable(clk);
ourport->clksrc = clksrc;
ourport->baudclk = clk;
}
switch (termios->c_cflag & CSIZE) {
case CS5:
dbg("config: 5bits/char\n");
ulcon = S3C2410_LCON_CS5;
break;
case CS6:
dbg("config: 6bits/char\n");
ulcon = S3C2410_LCON_CS6;
break;
case CS7:
dbg("config: 7bits/char\n");
ulcon = S3C2410_LCON_CS7;
break;
case CS8:
default:
dbg("config: 8bits/char\n");
ulcon = S3C2410_LCON_CS8;
break;
}
/* preserve original lcon IR settings */
ulcon |= (cfg->ulcon & S3C2410_LCON_IRM);
if (termios->c_cflag & CSTOPB)
ulcon |= S3C2410_LCON_STOPB;
umcon = (termios->c_cflag & CRTSCTS) ? S3C2410_UMCOM_AFC : 0;
if (termios->c_cflag & PARENB) {
if (termios->c_cflag & PARODD)
ulcon |= S3C2410_LCON_PODD;
else
ulcon |= S3C2410_LCON_PEVEN;
} else {
ulcon |= S3C2410_LCON_PNONE;
}
spin_lock_irqsave(&port->lock, flags);
dbg("setting ulcon to %08x, brddiv to %d\n", ulcon, quot);
wr_regl(port, S3C2410_ULCON, ulcon);
wr_regl(port, S3C2410_UBRDIV, quot);
wr_regl(port, S3C2410_UMCON, umcon);
dbg("uart: ulcon = 0x%08x, ucon = 0x%08x, ufcon = 0x%08x\n",
rd_regl(port, S3C2410_ULCON),
rd_regl(port, S3C2410_UCON),
rd_regl(port, S3C2410_UFCON));
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
/*
* Which character status flags are we interested in?
*/
port->read_status_mask = S3C2410_UERSTAT_OVERRUN;
if (termios->c_iflag & INPCK)
port->read_status_mask |= S3C2410_UERSTAT_FRAME | S3C2410_UERSTAT_PARITY;
/*
* Which character status flags should we ignore?
*/
port->ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= S3C2410_UERSTAT_OVERRUN;
if (termios->c_iflag & IGNBRK && termios->c_iflag & IGNPAR)
port->ignore_status_mask |= S3C2410_UERSTAT_FRAME;
/*
* Ignore all characters if CREAD is not set.
*/
if ((termios->c_cflag & CREAD) == 0)
port->ignore_status_mask |= RXSTAT_DUMMY_READ;
spin_unlock_irqrestore(&port->lock, flags);
}
static void
serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
struct uart_omap_port *up = to_uart_omap_port(port);
unsigned char cval = 0;
unsigned long flags = 0;
unsigned int baud, quot;
switch (termios->c_cflag & CSIZE) {
case CS5:
cval = UART_LCR_WLEN5;
break;
case CS6:
cval = UART_LCR_WLEN6;
break;
case CS7:
cval = UART_LCR_WLEN7;
break;
default:
case CS8:
cval = UART_LCR_WLEN8;
break;
}
if (termios->c_cflag & CSTOPB)
cval |= UART_LCR_STOP;
if (termios->c_cflag & PARENB)
cval |= UART_LCR_PARITY;
if (!(termios->c_cflag & PARODD))
cval |= UART_LCR_EPAR;
if (termios->c_cflag & CMSPAR)
cval |= UART_LCR_SPAR;
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/13);
quot = serial_omap_get_divisor(port, baud);
/* calculate wakeup latency constraint */
up->calc_latency = (USEC_PER_SEC * up->port.fifosize) / (baud / 8);
up->latency = up->calc_latency;
schedule_work(&up->qos_work);
up->dll = quot & 0xff;
up->dlh = quot >> 8;
up->mdr1 = UART_OMAP_MDR1_DISABLE;
up->fcr = UART_FCR_R_TRIG_01 | UART_FCR_T_TRIG_01 |
UART_FCR_ENABLE_FIFO;
/*
* Ok, we're now changing the port state. Do it with
* interrupts disabled.
*/
pm_runtime_get_sync(up->dev);
spin_lock_irqsave(&up->port.lock, flags);
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
if (termios->c_iflag & INPCK)
up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
if (termios->c_iflag & (BRKINT | PARMRK))
up->port.read_status_mask |= UART_LSR_BI;
/*
* Characters to ignore
*/
up->port.ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
if (termios->c_iflag & IGNBRK) {
up->port.ignore_status_mask |= UART_LSR_BI;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_OE;
}
/*
* ignore all characters if CREAD is not set
*/
if ((termios->c_cflag & CREAD) == 0)
up->port.ignore_status_mask |= UART_LSR_DR;
/*
* Modem status interrupts
*/
up->ier &= ~UART_IER_MSI;
if (UART_ENABLE_MS(&up->port, termios->c_cflag))
up->ier |= UART_IER_MSI;
serial_out(up, UART_IER, up->ier);
serial_out(up, UART_LCR, cval); /* reset DLAB */
up->lcr = cval;
up->scr = 0;
/* FIFOs and DMA Settings */
/* FCR can be changed only when the
* baud clock is not running
* DLL_REG and DLH_REG set to 0.
*/
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
serial_out(up, UART_DLL, 0);
serial_out(up, UART_DLM, 0);
serial_out(up, UART_LCR, 0);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
up->efr = serial_in(up, UART_EFR) & ~UART_EFR_ECB;
up->efr &= ~UART_EFR_SCD;
serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
up->mcr = serial_in(up, UART_MCR) & ~UART_MCR_TCRTLR;
serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
/* FIFO ENABLE, DMA MODE */
up->scr |= OMAP_UART_SCR_RX_TRIG_GRANU1_MASK;
/*
* NOTE: Setting OMAP_UART_SCR_RX_TRIG_GRANU1_MASK
* sets Enables the granularity of 1 for TRIGGER RX
* level. Along with setting RX FIFO trigger level
* to 1 (as noted below, 16 characters) and TLR[3:0]
* to zero this will result RX FIFO threshold level
* to 1 character, instead of 16 as noted in comment
* below.
*/
/* Set receive FIFO threshold to 16 characters and
* transmit FIFO threshold to 16 spaces
*/
up->fcr &= ~OMAP_UART_FCR_RX_FIFO_TRIG_MASK;
up->fcr &= ~OMAP_UART_FCR_TX_FIFO_TRIG_MASK;
up->fcr |= UART_FCR6_R_TRIGGER_16 | UART_FCR6_T_TRIGGER_24 |
UART_FCR_ENABLE_FIFO;
serial_out(up, UART_FCR, up->fcr);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
serial_out(up, UART_OMAP_SCR, up->scr);
/* Reset UART_MCR_TCRTLR: this must be done with the EFR_ECB bit set */
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
serial_out(up, UART_MCR, up->mcr);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
serial_out(up, UART_EFR, up->efr);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
/* Protocol, Baud Rate, and Interrupt Settings */
if (up->errata & UART_ERRATA_i202_MDR1_ACCESS)
serial_omap_mdr1_errataset(up, up->mdr1);
else
serial_out(up, UART_OMAP_MDR1, up->mdr1);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
serial_out(up, UART_LCR, 0);
serial_out(up, UART_IER, 0);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
serial_out(up, UART_DLL, up->dll); /* LS of divisor */
serial_out(up, UART_DLM, up->dlh); /* MS of divisor */
serial_out(up, UART_LCR, 0);
serial_out(up, UART_IER, up->ier);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
serial_out(up, UART_EFR, up->efr);
serial_out(up, UART_LCR, cval);
if (!serial_omap_baud_is_mode16(port, baud))
up->mdr1 = UART_OMAP_MDR1_13X_MODE;
else
up->mdr1 = UART_OMAP_MDR1_16X_MODE;
if (up->errata & UART_ERRATA_i202_MDR1_ACCESS)
serial_omap_mdr1_errataset(up, up->mdr1);
else
serial_out(up, UART_OMAP_MDR1, up->mdr1);
/* Configure flow control */
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
/* XON1/XOFF1 accessible mode B, TCRTLR=0, ECB=0 */
serial_out(up, UART_XON1, termios->c_cc[VSTART]);
serial_out(up, UART_XOFF1, termios->c_cc[VSTOP]);
/* Enable access to TCR/TLR */
serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
serial_out(up, UART_TI752_TCR, OMAP_UART_TCR_TRIG);
if (termios->c_cflag & CRTSCTS && up->port.flags & UPF_HARD_FLOW) {
/* Enable AUTORTS and AUTOCTS */
up->efr |= UART_EFR_CTS | UART_EFR_RTS;
/* Ensure MCR RTS is asserted */
up->mcr |= UART_MCR_RTS;
} else {
/* Disable AUTORTS and AUTOCTS */
up->efr &= ~(UART_EFR_CTS | UART_EFR_RTS);
}
if (up->port.flags & UPF_SOFT_FLOW) {
/* clear SW control mode bits */
up->efr &= OMAP_UART_SW_CLR;
/*
* IXON Flag:
* Enable XON/XOFF flow control on input.
* Receiver compares XON1, XOFF1.
*/
if (termios->c_iflag & IXON)
up->efr |= OMAP_UART_SW_RX;
/*
* IXOFF Flag:
* Enable XON/XOFF flow control on output.
* Transmit XON1, XOFF1
*/
if (termios->c_iflag & IXOFF)
up->efr |= OMAP_UART_SW_TX;
/*
* IXANY Flag:
* Enable any character to restart output.
* Operation resumes after receiving any
* character after recognition of the XOFF character
*/
if (termios->c_iflag & IXANY)
up->mcr |= UART_MCR_XONANY;
else
up->mcr &= ~UART_MCR_XONANY;
}
serial_out(up, UART_MCR, up->mcr);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
serial_out(up, UART_EFR, up->efr);
serial_out(up, UART_LCR, up->lcr);
serial_omap_set_mctrl(&up->port, up->port.mctrl);
spin_unlock_irqrestore(&up->port.lock, flags);
pm_runtime_mark_last_busy(up->dev);
pm_runtime_put_autosuspend(up->dev);
dev_dbg(up->port.dev, "serial_omap_set_termios+%d\n", up->port.line);
}
static void mcf_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
unsigned long flags;
unsigned int baud, baudclk;
unsigned char mr1, mr2;
baud = uart_get_baud_rate(port, termios, old, 0, 230400);
baudclk = ((MCF_BUSCLK / baud) + 16) / 32;
mr1 = MCFUART_MR1_RXIRQRDY | MCFUART_MR1_RXERRCHAR;
mr2 = 0;
switch (termios->c_cflag & CSIZE) {
case CS5: mr1 |= MCFUART_MR1_CS5; break;
case CS6: mr1 |= MCFUART_MR1_CS6; break;
case CS7: mr1 |= MCFUART_MR1_CS7; break;
case CS8:
default: mr1 |= MCFUART_MR1_CS8; break;
}
if (termios->c_cflag & PARENB) {
if (termios->c_cflag & CMSPAR) {
if (termios->c_cflag & PARODD)
mr1 |= MCFUART_MR1_PARITYMARK;
else
mr1 |= MCFUART_MR1_PARITYSPACE;
} else {
if (termios->c_cflag & PARODD)
mr1 |= MCFUART_MR1_PARITYODD;
else
mr1 |= MCFUART_MR1_PARITYEVEN;
}
} else {
mr1 |= MCFUART_MR1_PARITYNONE;
}
if (termios->c_cflag & CSTOPB)
mr2 |= MCFUART_MR2_STOP2;
else
mr2 |= MCFUART_MR2_STOP1;
if (termios->c_cflag & CRTSCTS) {
mr1 |= MCFUART_MR1_RXRTS;
mr2 |= MCFUART_MR2_TXCTS;
}
spin_lock_irqsave(&port->lock, flags);
writeb(MCFUART_UCR_CMDRESETRX, port->membase + MCFUART_UCR);
writeb(MCFUART_UCR_CMDRESETTX, port->membase + MCFUART_UCR);
writeb(MCFUART_UCR_CMDRESETMRPTR, port->membase + MCFUART_UCR);
writeb(mr1, port->membase + MCFUART_UMR);
writeb(mr2, port->membase + MCFUART_UMR);
writeb((baudclk & 0xff00) >> 8, port->membase + MCFUART_UBG1);
writeb((baudclk & 0xff), port->membase + MCFUART_UBG2);
writeb(MCFUART_UCSR_RXCLKTIMER | MCFUART_UCSR_TXCLKTIMER,
port->membase + MCFUART_UCSR);
writeb(MCFUART_UCR_RXENABLE | MCFUART_UCR_TXENABLE,
port->membase + MCFUART_UCR);
spin_unlock_irqrestore(&port->lock, flags);
}
/*
* Change the port parameters.
*/
static void tilegx_set_termios(struct uart_port *port,
struct ktermios *termios, struct ktermios *old)
{
int err;
UART_DIVISOR_t divisor;
UART_TYPE_t type;
unsigned int baud;
struct tile_uart_port *tile_uart;
gxio_uart_context_t *context;
tile_uart = container_of(port, struct tile_uart_port, uart);
if (!mutex_trylock(&tile_uart->mutex))
return;
context = &tile_uart->context;
/* Open the hypervisor device if we haven't already. */
if (context->fd < 0) {
err = gxio_uart_init(context, port->line);
if (err) {
mutex_unlock(&tile_uart->mutex);
return;
}
}
divisor.word = gxio_uart_read(context, UART_DIVISOR);
type.word = gxio_uart_read(context, UART_TYPE);
/* Divisor. */
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
divisor.divisor = uart_get_divisor(port, baud);
/* Byte size. */
if ((termios->c_cflag & CSIZE) == CS7)
type.dbits = UART_TYPE__DBITS_VAL_SEVEN_DBITS;
else
type.dbits = UART_TYPE__DBITS_VAL_EIGHT_DBITS;
/* Parity. */
if (termios->c_cflag & PARENB) {
/* Mark or Space parity. */
if (termios->c_cflag & CMSPAR)
if (termios->c_cflag & PARODD)
type.ptype = UART_TYPE__PTYPE_VAL_MARK;
else
type.ptype = UART_TYPE__PTYPE_VAL_SPACE;
else if (termios->c_cflag & PARODD)
type.ptype = UART_TYPE__PTYPE_VAL_ODD;
else
type.ptype = UART_TYPE__PTYPE_VAL_EVEN;
} else
type.ptype = UART_TYPE__PTYPE_VAL_NONE;
/* Stop bits. */
if (termios->c_cflag & CSTOPB)
type.sbits = UART_TYPE__SBITS_VAL_TWO_SBITS;
else
type.sbits = UART_TYPE__SBITS_VAL_ONE_SBITS;
/* Set the uart paramters. */
gxio_uart_write(context, UART_DIVISOR, divisor.word);
gxio_uart_write(context, UART_TYPE, type.word);
mutex_unlock(&tile_uart->mutex);
}
static void
clps711xuart_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
unsigned int ubrlcr, baud, quot;
unsigned long flags;
/*
* We don't implement CREAD.
*/
termios->c_cflag |= CREAD;
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
quot = uart_get_divisor(port, baud);
switch (termios->c_cflag & CSIZE) {
case CS5:
ubrlcr = UBRLCR_WRDLEN5;
break;
case CS6:
ubrlcr = UBRLCR_WRDLEN6;
break;
case CS7:
ubrlcr = UBRLCR_WRDLEN7;
break;
default: // CS8
ubrlcr = UBRLCR_WRDLEN8;
break;
}
if (termios->c_cflag & CSTOPB)
ubrlcr |= UBRLCR_XSTOP;
if (termios->c_cflag & PARENB) {
ubrlcr |= UBRLCR_PRTEN;
if (!(termios->c_cflag & PARODD))
ubrlcr |= UBRLCR_EVENPRT;
}
if (port->fifosize > 1)
ubrlcr |= UBRLCR_FIFOEN;
spin_lock_irqsave(&port->lock, flags);
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
port->read_status_mask = UARTDR_OVERR;
if (termios->c_iflag & INPCK)
port->read_status_mask |= UARTDR_PARERR | UARTDR_FRMERR;
/*
* Characters to ignore
*/
port->ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= UARTDR_FRMERR | UARTDR_PARERR;
if (termios->c_iflag & IGNBRK) {
/*
* If we're ignoring parity and break indicators,
* ignore overruns to (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= UARTDR_OVERR;
}
quot -= 1;
clps_writel(ubrlcr | quot, UBRLCR(port));
spin_unlock_irqrestore(&port->lock, flags);
}
static void ks8695uart_set_termios(struct uart_port *port, struct ktermios *termios, struct ktermios *old)
{
unsigned int lcr, fcr = 0;
unsigned long flags;
unsigned int baud, quot;
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
quot = uart_get_divisor(port, baud);
switch (termios->c_cflag & CSIZE) {
case CS5:
lcr = URCL_5;
break;
case CS6:
lcr = URCL_6;
break;
case CS7:
lcr = URCL_7;
break;
default:
lcr = URCL_8;
break;
}
/* stop bits */
if (termios->c_cflag & CSTOPB)
lcr |= URLC_URSB;
/* parity */
if (termios->c_cflag & PARENB) {
if (termios->c_cflag & CMSPAR) { /* Mark or Space parity */
if (termios->c_cflag & PARODD)
lcr |= URPE_MARK;
else
lcr |= URPE_SPACE;
}
else if (termios->c_cflag & PARODD)
lcr |= URPE_ODD;
else
lcr |= URPE_EVEN;
}
if (port->fifosize > 1)
fcr = URFC_URFRT_8 | URFC_URTFR | URFC_URRFR | URFC_URFE;
spin_lock_irqsave(&port->lock, flags);
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
port->read_status_mask = URLS_URROE;
if (termios->c_iflag & INPCK)
port->read_status_mask |= (URLS_URFE | URLS_URPE);
if (termios->c_iflag & (BRKINT | PARMRK))
port->read_status_mask |= URLS_URBI;
/*
* Characters to ignore
*/
port->ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= (URLS_URFE | URLS_URPE);
if (termios->c_iflag & IGNBRK) {
port->ignore_status_mask |= URLS_URBI;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= URLS_URROE;
}
/*
* Ignore all characters if CREAD is not set.
*/
if ((termios->c_cflag & CREAD) == 0)
port->ignore_status_mask |= UART_DUMMY_LSR_RX;
/* first, disable everything */
if (UART_ENABLE_MS(port, termios->c_cflag))
ks8695uart_enable_ms(port);
else
ks8695uart_disable_ms(port);
/* Set baud rate */
UART_PUT_BRDR(port, quot);
UART_PUT_LCR(port, lcr);
UART_PUT_FCR(port, fcr);
spin_unlock_irqrestore(&port->lock, flags);
}
static void cpm_uart_set_termios(struct uart_port *port,
struct ktermios *termios,
struct ktermios *old)
{
int baud;
unsigned long flags;
u16 cval, scval, prev_mode;
int bits, sbits;
struct uart_cpm_port *pinfo = (struct uart_cpm_port *)port;
smc_t __iomem *smcp = pinfo->smcp;
scc_t __iomem *sccp = pinfo->sccp;
int maxidl;
pr_debug("CPM uart[%d]:set_termios\n", port->line);
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
if (baud < HW_BUF_SPD_THRESHOLD ||
(pinfo->port.state && pinfo->port.state->port.low_latency))
pinfo->rx_fifosize = 1;
else
pinfo->rx_fifosize = RX_BUF_SIZE;
/* MAXIDL is the timeout after which a receive buffer is closed
* when not full if no more characters are received.
* We calculate it from the baudrate so that the duration is
* always the same at standard rates: about 4ms.
*/
maxidl = baud / 2400;
if (maxidl < 1)
maxidl = 1;
if (maxidl > 0x10)
maxidl = 0x10;
/* Character length programmed into the mode register is the
* sum of: 1 start bit, number of data bits, 0 or 1 parity bit,
* 1 or 2 stop bits, minus 1.
* The value 'bits' counts this for us.
*/
cval = 0;
scval = 0;
/* byte size */
switch (termios->c_cflag & CSIZE) {
case CS5:
bits = 5;
break;
case CS6:
bits = 6;
break;
case CS7:
bits = 7;
break;
case CS8:
bits = 8;
break;
/* Never happens, but GCC is too dumb to figure it out */
default:
bits = 8;
break;
}
sbits = bits - 5;
if (termios->c_cflag & CSTOPB) {
cval |= SMCMR_SL; /* Two stops */
scval |= SCU_PSMR_SL;
bits++;
}
if (termios->c_cflag & PARENB) {
cval |= SMCMR_PEN;
scval |= SCU_PSMR_PEN;
bits++;
if (!(termios->c_cflag & PARODD)) {
cval |= SMCMR_PM_EVEN;
scval |= (SCU_PSMR_REVP | SCU_PSMR_TEVP);
}
}
/*
* Update the timeout
*/
uart_update_timeout(port, termios->c_cflag, baud);
/*
* Set up parity check flag
*/
#define RELEVANT_IFLAG(iflag) (iflag & (IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK))
port->read_status_mask = (BD_SC_EMPTY | BD_SC_OV);
if (termios->c_iflag & INPCK)
port->read_status_mask |= BD_SC_FR | BD_SC_PR;
if ((termios->c_iflag & BRKINT) || (termios->c_iflag & PARMRK))
port->read_status_mask |= BD_SC_BR;
/*
* Characters to ignore
*/
port->ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= BD_SC_PR | BD_SC_FR;
if (termios->c_iflag & IGNBRK) {
port->ignore_status_mask |= BD_SC_BR;
/*
* If we're ignore parity and break indicators, ignore
* overruns too. (For real raw support).
*/
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= BD_SC_OV;
}
/*
* !!! ignore all characters if CREAD is not set
*/
if ((termios->c_cflag & CREAD) == 0)
port->read_status_mask &= ~BD_SC_EMPTY;
spin_lock_irqsave(&port->lock, flags);
/* Start bit has not been added (so don't, because we would just
* subtract it later), and we need to add one for the number of
* stops bits (there is always at least one).
*/
bits++;
if (IS_SMC(pinfo)) {
/*
* MRBLR can be changed while an SMC/SCC is operating only
* if it is done in a single bus cycle with one 16-bit move
* (not two 8-bit bus cycles back-to-back). This occurs when
* the cp shifts control to the next RxBD, so the change does
* not take effect immediately. To guarantee the exact RxBD
* on which the change occurs, change MRBLR only while the
* SMC/SCC receiver is disabled.
*/
out_be16(&pinfo->smcup->smc_mrblr, pinfo->rx_fifosize);
out_be16(&pinfo->smcup->smc_maxidl, maxidl);
/* Set the mode register. We want to keep a copy of the
* enables, because we want to put them back if they were
* present.
*/
prev_mode = in_be16(&smcp->smc_smcmr) & (SMCMR_REN | SMCMR_TEN);
/* Output in *one* operation, so we don't interrupt RX/TX if they
* were already enabled. */
out_be16(&smcp->smc_smcmr, smcr_mk_clen(bits) | cval |
SMCMR_SM_UART | prev_mode);
} else {
out_be16(&pinfo->sccup->scc_genscc.scc_mrblr, pinfo->rx_fifosize);
out_be16(&pinfo->sccup->scc_maxidl, maxidl);
out_be16(&sccp->scc_psmr, (sbits << 12) | scval);
}
if (pinfo->clk)
clk_set_rate(pinfo->clk, baud);
else
cpm_set_brg(pinfo->brg - 1, baud);
spin_unlock_irqrestore(&port->lock, flags);
}
static void
imx_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
struct imx_port *sport = (struct imx_port *)port;
unsigned long flags;
unsigned int ucr2, old_ucr1, old_txrxen, baud, quot;
unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8;
unsigned int div, ufcr;
unsigned long num, denom;
uint64_t tdiv64;
/*
* If we don't support modem control lines, don't allow
* these to be set.
*/
if (0) {
termios->c_cflag &= ~(HUPCL | CRTSCTS | CMSPAR);
termios->c_cflag |= CLOCAL;
}
/*
* We only support CS7 and CS8.
*/
while ((termios->c_cflag & CSIZE) != CS7 &&
(termios->c_cflag & CSIZE) != CS8) {
termios->c_cflag &= ~CSIZE;
termios->c_cflag |= old_csize;
old_csize = CS8;
}
if ((termios->c_cflag & CSIZE) == CS8)
ucr2 = UCR2_WS | UCR2_SRST | UCR2_IRTS;
else
ucr2 = UCR2_SRST | UCR2_IRTS;
if (termios->c_cflag & CRTSCTS) {
if( sport->have_rtscts ) {
ucr2 &= ~UCR2_IRTS;
ucr2 |= UCR2_CTSC;
} else {
termios->c_cflag &= ~CRTSCTS;
}
}
if (termios->c_cflag & CSTOPB)
ucr2 |= UCR2_STPB;
if (termios->c_cflag & PARENB) {
ucr2 |= UCR2_PREN;
if (termios->c_cflag & PARODD)
ucr2 |= UCR2_PROE;
}
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 50, port->uartclk / 16);
quot = uart_get_divisor(port, baud);
spin_lock_irqsave(&sport->port.lock, flags);
sport->port.read_status_mask = 0;
if (termios->c_iflag & INPCK)
sport->port.read_status_mask |= (URXD_FRMERR | URXD_PRERR);
if (termios->c_iflag & (BRKINT | PARMRK))
sport->port.read_status_mask |= URXD_BRK;
/*
* Characters to ignore
*/
sport->port.ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
sport->port.ignore_status_mask |= URXD_PRERR;
if (termios->c_iflag & IGNBRK) {
sport->port.ignore_status_mask |= URXD_BRK;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
sport->port.ignore_status_mask |= URXD_OVRRUN;
}
del_timer_sync(&sport->timer);
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
/*
* disable interrupts and drain transmitter
*/
old_ucr1 = readl(sport->port.membase + UCR1);
writel(old_ucr1 & ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN),
sport->port.membase + UCR1);
while ( !(readl(sport->port.membase + USR2) & USR2_TXDC))
barrier();
/* then, disable everything */
old_txrxen = readl(sport->port.membase + UCR2);
writel(old_txrxen & ~( UCR2_TXEN | UCR2_RXEN),
sport->port.membase + UCR2);
old_txrxen &= (UCR2_TXEN | UCR2_RXEN);
if (USE_IRDA(sport)) {
/*
* use maximum available submodule frequency to
* avoid missing short pulses due to low sampling rate
*/
div = 1;
} else {
div = sport->port.uartclk / (baud * 16);
if (div > 7)
div = 7;
if (!div)
div = 1;
}
rational_best_approximation(16 * div * baud, sport->port.uartclk,
1 << 16, 1 << 16, &num, &denom);
if (port->state && port->state->port.tty) {
tdiv64 = sport->port.uartclk;
tdiv64 *= num;
do_div(tdiv64, denom * 16 * div);
tty_encode_baud_rate(sport->port.state->port.tty,
(speed_t)tdiv64, (speed_t)tdiv64);
}
num -= 1;
denom -= 1;
ufcr = readl(sport->port.membase + UFCR);
ufcr = (ufcr & (~UFCR_RFDIV)) | UFCR_RFDIV_REG(div);
writel(ufcr, sport->port.membase + UFCR);
writel(num, sport->port.membase + UBIR);
writel(denom, sport->port.membase + UBMR);
if (!cpu_is_mx1())
writel(sport->port.uartclk / div / 1000,
sport->port.membase + MX2_ONEMS);
writel(old_ucr1, sport->port.membase + UCR1);
/* set the parity, stop bits and data size */
writel(ucr2 | old_txrxen, sport->port.membase + UCR2);
if (UART_ENABLE_MS(&sport->port, termios->c_cflag))
imx_enable_ms(&sport->port);
spin_unlock_irqrestore(&sport->port.lock, flags);
}
static void
pl010_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned int lcr_h, old_cr;
unsigned long flags;
unsigned int baud, quot;
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16);
quot = uart_get_divisor(port, baud);
switch (termios->c_cflag & CSIZE) {
case CS5:
lcr_h = UART01x_LCRH_WLEN_5;
break;
case CS6:
lcr_h = UART01x_LCRH_WLEN_6;
break;
case CS7:
lcr_h = UART01x_LCRH_WLEN_7;
break;
default: // CS8
lcr_h = UART01x_LCRH_WLEN_8;
break;
}
if (termios->c_cflag & CSTOPB)
lcr_h |= UART01x_LCRH_STP2;
if (termios->c_cflag & PARENB) {
lcr_h |= UART01x_LCRH_PEN;
if (!(termios->c_cflag & PARODD))
lcr_h |= UART01x_LCRH_EPS;
}
if (uap->port.fifosize > 1)
lcr_h |= UART01x_LCRH_FEN;
spin_lock_irqsave(&uap->port.lock, flags);
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
uap->port.read_status_mask = UART01x_RSR_OE;
if (termios->c_iflag & INPCK)
uap->port.read_status_mask |= UART01x_RSR_FE | UART01x_RSR_PE;
if (termios->c_iflag & (BRKINT | PARMRK))
uap->port.read_status_mask |= UART01x_RSR_BE;
/*
* Characters to ignore
*/
uap->port.ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
uap->port.ignore_status_mask |= UART01x_RSR_FE | UART01x_RSR_PE;
if (termios->c_iflag & IGNBRK) {
uap->port.ignore_status_mask |= UART01x_RSR_BE;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
uap->port.ignore_status_mask |= UART01x_RSR_OE;
}
/*
* Ignore all characters if CREAD is not set.
*/
if ((termios->c_cflag & CREAD) == 0)
uap->port.ignore_status_mask |= UART_DUMMY_RSR_RX;
/* first, disable everything */
old_cr = readb(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
if (UART_ENABLE_MS(port, termios->c_cflag))
old_cr |= UART010_CR_MSIE;
writel(0, uap->port.membase + UART010_CR);
/* Set baud rate */
quot -= 1;
writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM);
writel(quot & 0xff, uap->port.membase + UART010_LCRL);
/*
* ----------v----------v----------v----------v-----
* NOTE: MUST BE WRITTEN AFTER UARTLCR_M & UARTLCR_L
* ----------^----------^----------^----------^-----
*/
writel(lcr_h, uap->port.membase + UART010_LCRH);
writel(old_cr, uap->port.membase + UART010_CR);
spin_unlock_irqrestore(&uap->port.lock, flags);
}
static void mxs_auart_settermios(struct uart_port *u,
struct ktermios *termios,
struct ktermios *old)
{
u32 bm, ctrl, ctrl2, div;
unsigned int cflag, baud;
cflag = termios->c_cflag;
ctrl = AUART_LINECTRL_FEN;
ctrl2 = readl(u->membase + AUART_CTRL2);
/* byte size */
switch (cflag & CSIZE) {
case CS5:
bm = 0;
break;
case CS6:
bm = 1;
break;
case CS7:
bm = 2;
break;
case CS8:
bm = 3;
break;
default:
return;
}
ctrl |= AUART_LINECTRL_WLEN(bm);
/* parity */
if (cflag & PARENB) {
ctrl |= AUART_LINECTRL_PEN;
if ((cflag & PARODD) == 0)
ctrl |= AUART_LINECTRL_EPS;
}
u->read_status_mask = 0;
if (termios->c_iflag & INPCK)
u->read_status_mask |= AUART_STAT_PERR;
if (termios->c_iflag & (BRKINT | PARMRK))
u->read_status_mask |= AUART_STAT_BERR;
/*
* Characters to ignore
*/
u->ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
u->ignore_status_mask |= AUART_STAT_PERR;
if (termios->c_iflag & IGNBRK) {
u->ignore_status_mask |= AUART_STAT_BERR;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
u->ignore_status_mask |= AUART_STAT_OERR;
}
/*
* ignore all characters if CREAD is not set
*/
if (cflag & CREAD)
ctrl2 |= AUART_CTRL2_RXE;
else
ctrl2 &= ~AUART_CTRL2_RXE;
/* figure out the stop bits requested */
if (cflag & CSTOPB)
ctrl |= AUART_LINECTRL_STP2;
/* figure out the hardware flow control settings */
if (cflag & CRTSCTS)
ctrl2 |= AUART_CTRL2_CTSEN;
else
ctrl2 &= ~AUART_CTRL2_CTSEN;
/* set baud rate */
baud = uart_get_baud_rate(u, termios, old, 0, u->uartclk);
div = u->uartclk * 32 / baud;
ctrl |= AUART_LINECTRL_BAUD_DIVFRAC(div & 0x3F);
ctrl |= AUART_LINECTRL_BAUD_DIVINT(div >> 6);
writel(ctrl, u->membase + AUART_LINECTRL);
writel(ctrl2, u->membase + AUART_CTRL2);
}
static void
sa1100_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
struct sa1100_port *sport = (struct sa1100_port *)port;
unsigned long flags;
unsigned int utcr0, old_utcr3, baud, quot;
unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8;
/*
* We only support CS7 and CS8.
*/
while ((termios->c_cflag & CSIZE) != CS7 &&
(termios->c_cflag & CSIZE) != CS8) {
termios->c_cflag &= ~CSIZE;
termios->c_cflag |= old_csize;
old_csize = CS8;
}
if ((termios->c_cflag & CSIZE) == CS8)
utcr0 = UTCR0_DSS;
else
utcr0 = 0;
if (termios->c_cflag & CSTOPB)
utcr0 |= UTCR0_SBS;
if (termios->c_cflag & PARENB) {
utcr0 |= UTCR0_PE;
if (!(termios->c_cflag & PARODD))
utcr0 |= UTCR0_OES;
}
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
quot = uart_get_divisor(port, baud);
spin_lock_irqsave(&sport->port.lock, flags);
sport->port.read_status_mask &= UTSR0_TO_SM(UTSR0_TFS);
sport->port.read_status_mask |= UTSR1_TO_SM(UTSR1_ROR);
if (termios->c_iflag & INPCK)
sport->port.read_status_mask |=
UTSR1_TO_SM(UTSR1_FRE | UTSR1_PRE);
if (termios->c_iflag & (BRKINT | PARMRK))
sport->port.read_status_mask |=
UTSR0_TO_SM(UTSR0_RBB | UTSR0_REB);
/*
* Characters to ignore
*/
sport->port.ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
sport->port.ignore_status_mask |=
UTSR1_TO_SM(UTSR1_FRE | UTSR1_PRE);
if (termios->c_iflag & IGNBRK) {
sport->port.ignore_status_mask |=
UTSR0_TO_SM(UTSR0_RBB | UTSR0_REB);
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
sport->port.ignore_status_mask |=
UTSR1_TO_SM(UTSR1_ROR);
}
del_timer_sync(&sport->timer);
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
/*
* disable interrupts and drain transmitter
*/
old_utcr3 = UART_GET_UTCR3(sport);
UART_PUT_UTCR3(sport, old_utcr3 & ~(UTCR3_RIE | UTCR3_TIE));
while (UART_GET_UTSR1(sport) & UTSR1_TBY)
barrier();
/* then, disable everything */
UART_PUT_UTCR3(sport, 0);
/* set the parity, stop bits and data size */
UART_PUT_UTCR0(sport, utcr0);
/* set the baud rate */
quot -= 1;
UART_PUT_UTCR1(sport, ((quot & 0xf00) >> 8));
UART_PUT_UTCR2(sport, (quot & 0xff));
UART_PUT_UTSR0(sport, -1);
UART_PUT_UTCR3(sport, old_utcr3);
if (UART_ENABLE_MS(&sport->port, termios->c_cflag))
sa1100_enable_ms(&sport->port);
spin_unlock_irqrestore(&sport->port.lock, flags);
}
static void
serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
struct uart_omap_port *up = (struct uart_omap_port *)port;
unsigned char cval = 0;
unsigned char efr = 0;
unsigned long flags = 0;
unsigned int baud, quot;
switch (termios->c_cflag & CSIZE) {
case CS5:
cval = UART_LCR_WLEN5;
break;
case CS6:
cval = UART_LCR_WLEN6;
break;
case CS7:
cval = UART_LCR_WLEN7;
break;
default:
case CS8:
cval = UART_LCR_WLEN8;
break;
}
if (termios->c_cflag & CSTOPB)
cval |= UART_LCR_STOP;
if (termios->c_cflag & PARENB)
cval |= UART_LCR_PARITY;
if (!(termios->c_cflag & PARODD))
cval |= UART_LCR_EPAR;
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/13);
/* Added for the suporrt of DPLL, frequency changes
* This value can be used to recalculate the DLLand
* DLH values. If this function is not called for
* particulate UART it would remain as 0.
*/
up->baud_rate = baud;
quot = serial_omap_get_divisor(port, baud);
up->fcr = UART_FCR_R_TRIG_01 | UART_FCR_T_TRIG_01 |
UART_FCR_ENABLE_FIFO;
if (up->use_dma)
up->fcr |= UART_FCR_DMA_SELECT;
/*
* Ok, we're now changing the port state. Do it with
* interrupts disabled.
*/
spin_lock_irqsave(&up->port.lock, flags);
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
if (termios->c_iflag & INPCK)
up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
if (termios->c_iflag & (BRKINT | PARMRK))
up->port.read_status_mask |= UART_LSR_BI;
/*
* Characters to ignore
*/
up->port.ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
if (termios->c_iflag & IGNBRK) {
up->port.ignore_status_mask |= UART_LSR_BI;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_OE;
}
/*
* ignore all characters if CREAD is not set
*/
if ((termios->c_cflag & CREAD) == 0)
up->port.ignore_status_mask |= UART_LSR_DR;
/*
* Modem status interrupts
*/
up->ier &= ~UART_IER_MSI;
if (UART_ENABLE_MS(&up->port, termios->c_cflag))
up->ier |= UART_IER_MSI;
serial_out(up, UART_IER, up->ier);
serial_out(up, UART_LCR, cval); /* reset DLAB */
/* FIFOs and DMA Settings */
/* FCR can be changed only when the
* baud clock is not running
* DLL_REG and DLH_REG set to 0.
*/
serial_out(up, UART_LCR, UART_LCR_DLAB);
serial_out(up, UART_DLL, 0);
serial_out(up, UART_DLM, 0);
serial_out(up, UART_LCR, 0);
serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
up->efr = serial_in(up, UART_EFR);
serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
serial_out(up, UART_LCR, 0);
up->mcr = serial_in(up, UART_MCR);
serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
/* FIFO ENABLE, DMA MODE */
serial_out(up, UART_FCR, up->fcr);
serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
if (up->use_dma) {
if (up->uart_dma.tx_threshold) {
serial_out(up, UART_MDR3,
SET_DMA_TX_THRESHOLD);
serial_out(up, UART_TX_DMA_THRESHOLD,
TX_FIFO_THR_LVL);
}
serial_out(up, UART_TI752_TLR, 0);
serial_out(up, UART_OMAP_SCR,
(UART_FCR_TRIGGER_4 | UART_FCR_TRIGGER_8));
}
serial_out(up, UART_EFR, up->efr);
serial_out(up, UART_LCR, UART_LCR_DLAB);
serial_out(up, UART_MCR, up->mcr);
/* Protocol, Baud Rate, and Interrupt Settings */
serial_out(up, UART_OMAP_MDR1, OMAP_MDR1_DISABLE);
serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
up->efr = serial_in(up, UART_EFR);
serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
serial_out(up, UART_LCR, 0);
serial_out(up, UART_IER, 0);
serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
serial_out(up, UART_DLL, quot & 0xff); /* LS of divisor */
serial_out(up, UART_DLM, quot >> 8); /* MS of divisor */
serial_out(up, UART_LCR, 0);
serial_out(up, UART_IER, up->ier);
serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
serial_out(up, UART_EFR, up->efr);
serial_out(up, UART_LCR, cval);
if (baud > 230400 && baud != 3000000)
serial_out(up, UART_OMAP_MDR1, OMAP_MDR1_MODE13X);
else
serial_out(up, UART_OMAP_MDR1, OMAP_MDR1_MODE16X);
/* Hardware Flow Control Configuration */
if (termios->c_cflag & CRTSCTS) {
efr |= (UART_EFR_CTS | UART_EFR_RTS);
serial_out(up, UART_LCR, UART_LCR_DLAB);
up->mcr = serial_in(up, UART_MCR);
serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
up->efr = serial_in(up, UART_EFR);
serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
serial_out(up, UART_TI752_TCR, OMAP_UART_TCR_TRIG);
serial_out(up, UART_EFR, efr); /* Enable AUTORTS and AUTOCTS */
serial_out(up, UART_LCR, UART_LCR_DLAB);
serial_out(up, UART_MCR, up->mcr | UART_MCR_RTS);
serial_out(up, UART_LCR, cval);
}
serial_omap_set_mctrl(&up->port, up->port.mctrl);
/* Software Flow Control Configuration */
if (termios->c_iflag & (IXON | IXOFF))
serial_omap_configure_xonxoff(up, termios);
spin_unlock_irqrestore(&up->port.lock, flags);
dev_dbg(up->port.dev, "serial_omap_set_termios+%d\n", up->pdev->id);
}
/**
* xuartps_set_termios - termios operations, handling data length, parity,
* stop bits, flow control, baud rate
* @port: Handle to the uart port structure
* @termios: Handle to the input termios structure
* @old: Values of the previously saved termios structure
*
**/
static void xuartps_set_termios(struct uart_port *port,
struct ktermios *termios, struct ktermios *old)
{
unsigned int cval = 0;
unsigned int baud;
unsigned long flags;
unsigned int ctrl_reg, mode_reg;
spin_lock_irqsave(&port->lock, flags);
/* Empty the receive FIFO 1st before making changes */
while ((xuartps_readl(XUARTPS_SR_OFFSET) &
XUARTPS_SR_RXEMPTY) != XUARTPS_SR_RXEMPTY) {
xuartps_readl(XUARTPS_FIFO_OFFSET);
}
/* Disable the TX and RX to set baud rate */
xuartps_writel(xuartps_readl(XUARTPS_CR_OFFSET) |
(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS),
XUARTPS_CR_OFFSET);
/* Min baud rate = 6bps and Max Baud Rate is 10Mbps for 100Mhz clk */
baud = uart_get_baud_rate(port, termios, old, 0, 10000000);
baud = xuartps_set_baud_rate(port, baud);
if (tty_termios_baud_rate(termios))
tty_termios_encode_baud_rate(termios, baud, baud);
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
/* Set TX/RX Reset */
xuartps_writel(xuartps_readl(XUARTPS_CR_OFFSET) |
(XUARTPS_CR_TXRST | XUARTPS_CR_RXRST),
XUARTPS_CR_OFFSET);
ctrl_reg = xuartps_readl(XUARTPS_CR_OFFSET);
/* Clear the RX disable and TX disable bits and then set the TX enable
* bit and RX enable bit to enable the transmitter and receiver.
*/
xuartps_writel(
(ctrl_reg & ~(XUARTPS_CR_TX_DIS | XUARTPS_CR_RX_DIS))
| (XUARTPS_CR_TX_EN | XUARTPS_CR_RX_EN),
XUARTPS_CR_OFFSET);
xuartps_writel(10, XUARTPS_RXTOUT_OFFSET);
port->read_status_mask = XUARTPS_IXR_TXEMPTY | XUARTPS_IXR_RXTRIG |
XUARTPS_IXR_OVERRUN | XUARTPS_IXR_TOUT;
port->ignore_status_mask = 0;
if (termios->c_iflag & INPCK)
port->read_status_mask |= XUARTPS_IXR_PARITY |
XUARTPS_IXR_FRAMING;
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= XUARTPS_IXR_PARITY |
XUARTPS_IXR_FRAMING | XUARTPS_IXR_OVERRUN;
/* ignore all characters if CREAD is not set */
if ((termios->c_cflag & CREAD) == 0)
port->ignore_status_mask |= XUARTPS_IXR_RXTRIG |
XUARTPS_IXR_TOUT | XUARTPS_IXR_PARITY |
XUARTPS_IXR_FRAMING | XUARTPS_IXR_OVERRUN;
mode_reg = xuartps_readl(XUARTPS_MR_OFFSET);
/* Handling Data Size */
switch (termios->c_cflag & CSIZE) {
case CS6:
cval |= XUARTPS_MR_CHARLEN_6_BIT;
break;
case CS7:
cval |= XUARTPS_MR_CHARLEN_7_BIT;
break;
default:
case CS8:
cval |= XUARTPS_MR_CHARLEN_8_BIT;
termios->c_cflag &= ~CSIZE;
termios->c_cflag |= CS8;
break;
}
/* Handling Parity and Stop Bits length */
if (termios->c_cflag & CSTOPB)
cval |= XUARTPS_MR_STOPMODE_2_BIT; /* 2 STOP bits */
else
cval |= XUARTPS_MR_STOPMODE_1_BIT; /* 1 STOP bit */
if (termios->c_cflag & PARENB) {
/* Mark or Space parity */
if (termios->c_cflag & CMSPAR) {
if (termios->c_cflag & PARODD)
cval |= XUARTPS_MR_PARITY_MARK;
else
cval |= XUARTPS_MR_PARITY_SPACE;
} else if (termios->c_cflag & PARODD)
cval |= XUARTPS_MR_PARITY_ODD;
else
cval |= XUARTPS_MR_PARITY_EVEN;
} else
cval |= XUARTPS_MR_PARITY_NONE;
xuartps_writel(cval , XUARTPS_MR_OFFSET);
spin_unlock_irqrestore(&port->lock, flags);
}
/*
* OMAP can use "CLK / (16 or 13) / div" for baud rate. And then we have have
* some differences in how we want to handle flow control.
*/
static void omap_8250_set_termios(struct uart_port *port,
struct ktermios *termios,
struct ktermios *old)
{
struct uart_8250_port *up = up_to_u8250p(port);
struct omap8250_priv *priv = up->port.private_data;
unsigned char cval = 0;
unsigned int baud;
switch (termios->c_cflag & CSIZE) {
case CS5:
cval = UART_LCR_WLEN5;
break;
case CS6:
cval = UART_LCR_WLEN6;
break;
case CS7:
cval = UART_LCR_WLEN7;
break;
default:
case CS8:
cval = UART_LCR_WLEN8;
break;
}
if (termios->c_cflag & CSTOPB)
cval |= UART_LCR_STOP;
if (termios->c_cflag & PARENB)
cval |= UART_LCR_PARITY;
if (!(termios->c_cflag & PARODD))
cval |= UART_LCR_EPAR;
if (termios->c_cflag & CMSPAR)
cval |= UART_LCR_SPAR;
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old,
port->uartclk / 16 / UART_DIV_MAX,
port->uartclk / 13);
omap_8250_get_divisor(port, baud, priv);
/*
* Ok, we're now changing the port state. Do it with
* interrupts disabled.
*/
pm_runtime_get_sync(port->dev);
spin_lock_irq(&port->lock);
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
if (termios->c_iflag & INPCK)
up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
if (termios->c_iflag & (IGNBRK | PARMRK))
up->port.read_status_mask |= UART_LSR_BI;
/*
* Characters to ignore
*/
up->port.ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
if (termios->c_iflag & IGNBRK) {
up->port.ignore_status_mask |= UART_LSR_BI;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_OE;
}
/*
* ignore all characters if CREAD is not set
*/
if ((termios->c_cflag & CREAD) == 0)
up->port.ignore_status_mask |= UART_LSR_DR;
/*
* Modem status interrupts
*/
up->ier &= ~UART_IER_MSI;
if (UART_ENABLE_MS(&up->port, termios->c_cflag))
up->ier |= UART_IER_MSI;
up->lcr = cval;
/* Up to here it was mostly serial8250_do_set_termios() */
/*
* We enable TRIG_GRANU for RX and TX and additionaly we set
* SCR_TX_EMPTY bit. The result is the following:
* - RX_TRIGGER amount of bytes in the FIFO will cause an interrupt.
* - less than RX_TRIGGER number of bytes will also cause an interrupt
* once the UART decides that there no new bytes arriving.
* - Once THRE is enabled, the interrupt will be fired once the FIFO is
* empty - the trigger level is ignored here.
*
* Once DMA is enabled:
* - UART will assert the TX DMA line once there is room for TX_TRIGGER
* bytes in the TX FIFO. On each assert the DMA engine will move
* TX_TRIGGER bytes into the FIFO.
* - UART will assert the RX DMA line once there are RX_TRIGGER bytes in
* the FIFO and move RX_TRIGGER bytes.
* This is because threshold and trigger values are the same.
*/
up->fcr = UART_FCR_ENABLE_FIFO;
up->fcr |= TRIGGER_FCR_MASK(TX_TRIGGER) << OMAP_UART_FCR_TX_TRIG;
up->fcr |= TRIGGER_FCR_MASK(RX_TRIGGER) << OMAP_UART_FCR_RX_TRIG;
priv->scr = OMAP_UART_SCR_RX_TRIG_GRANU1_MASK | OMAP_UART_SCR_TX_EMPTY |
OMAP_UART_SCR_TX_TRIG_GRANU1_MASK;
if (up->dma)
priv->scr |= OMAP_UART_SCR_DMAMODE_1 |
OMAP_UART_SCR_DMAMODE_CTL;
priv->xon = termios->c_cc[VSTART];
priv->xoff = termios->c_cc[VSTOP];
priv->efr = 0;
up->port.status &= ~(UPSTAT_AUTOCTS | UPSTAT_AUTORTS | UPSTAT_AUTOXOFF);
if (termios->c_cflag & CRTSCTS && up->port.flags & UPF_HARD_FLOW) {
/* Enable AUTOCTS (autoRTS is enabled when RTS is raised) */
up->port.status |= UPSTAT_AUTOCTS | UPSTAT_AUTORTS;
priv->efr |= UART_EFR_CTS;
} else if (up->port.flags & UPF_SOFT_FLOW) {
/*
* OMAP rx s/w flow control is borked; the transmitter remains
* stuck off even if rx flow control is subsequently disabled
*/
/*
* IXOFF Flag:
* Enable XON/XOFF flow control on output.
* Transmit XON1, XOFF1
*/
if (termios->c_iflag & IXOFF) {
up->port.status |= UPSTAT_AUTOXOFF;
priv->efr |= OMAP_UART_SW_TX;
}
}
omap8250_restore_regs(up);
spin_unlock_irq(&up->port.lock);
pm_runtime_mark_last_busy(port->dev);
pm_runtime_put_autosuspend(port->dev);
/* calculate wakeup latency constraint */
priv->calc_latency = USEC_PER_SEC * 64 * 8 / baud;
priv->latency = priv->calc_latency;
schedule_work(&priv->qos_work);
/* Don't rewrite B0 */
if (tty_termios_baud_rate(termios))
tty_termios_encode_baud_rate(termios, baud, baud);
}
/**
* cdns_uart_set_termios - termios operations, handling data length, parity,
* stop bits, flow control, baud rate
* @port: Handle to the uart port structure
* @termios: Handle to the input termios structure
* @old: Values of the previously saved termios structure
*/
static void cdns_uart_set_termios(struct uart_port *port,
struct ktermios *termios, struct ktermios *old)
{
unsigned int cval = 0;
unsigned int baud, minbaud, maxbaud;
unsigned long flags;
unsigned int ctrl_reg, mode_reg;
spin_lock_irqsave(&port->lock, flags);
/* Wait for the transmit FIFO to empty before making changes */
if (!(cdns_uart_readl(CDNS_UART_CR_OFFSET) & CDNS_UART_CR_TX_DIS)) {
while (!(cdns_uart_readl(CDNS_UART_SR_OFFSET) &
CDNS_UART_SR_TXEMPTY)) {
cpu_relax();
}
}
/* Disable the TX and RX to set baud rate */
ctrl_reg = cdns_uart_readl(CDNS_UART_CR_OFFSET);
ctrl_reg |= CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS;
cdns_uart_writel(ctrl_reg, CDNS_UART_CR_OFFSET);
/*
* Min baud rate = 6bps and Max Baud Rate is 10Mbps for 100Mhz clk
* min and max baud should be calculated here based on port->uartclk.
* this way we get a valid baud and can safely call set_baud()
*/
minbaud = port->uartclk /
((CDNS_UART_BDIV_MAX + 1) * CDNS_UART_CD_MAX * 8);
maxbaud = port->uartclk / (CDNS_UART_BDIV_MIN + 1);
baud = uart_get_baud_rate(port, termios, old, minbaud, maxbaud);
baud = cdns_uart_set_baud_rate(port, baud);
if (tty_termios_baud_rate(termios))
tty_termios_encode_baud_rate(termios, baud, baud);
/* Update the per-port timeout. */
uart_update_timeout(port, termios->c_cflag, baud);
/* Set TX/RX Reset */
ctrl_reg = cdns_uart_readl(CDNS_UART_CR_OFFSET);
ctrl_reg |= CDNS_UART_CR_TXRST | CDNS_UART_CR_RXRST;
cdns_uart_writel(ctrl_reg, CDNS_UART_CR_OFFSET);
/*
* Clear the RX disable and TX disable bits and then set the TX enable
* bit and RX enable bit to enable the transmitter and receiver.
*/
ctrl_reg = cdns_uart_readl(CDNS_UART_CR_OFFSET);
ctrl_reg &= ~(CDNS_UART_CR_TX_DIS | CDNS_UART_CR_RX_DIS);
ctrl_reg |= CDNS_UART_CR_TX_EN | CDNS_UART_CR_RX_EN;
cdns_uart_writel(ctrl_reg, CDNS_UART_CR_OFFSET);
cdns_uart_writel(rx_timeout, CDNS_UART_RXTOUT_OFFSET);
port->read_status_mask = CDNS_UART_IXR_TXEMPTY | CDNS_UART_IXR_RXTRIG |
CDNS_UART_IXR_OVERRUN | CDNS_UART_IXR_TOUT;
port->ignore_status_mask = 0;
if (termios->c_iflag & INPCK)
port->read_status_mask |= CDNS_UART_IXR_PARITY |
CDNS_UART_IXR_FRAMING;
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |= CDNS_UART_IXR_PARITY |
CDNS_UART_IXR_FRAMING;
/* ignore all characters if CREAD is not set */
if ((termios->c_cflag & CREAD) == 0)
port->ignore_status_mask |= CDNS_UART_IXR_RXTRIG |
CDNS_UART_IXR_TOUT | CDNS_UART_IXR_PARITY |
CDNS_UART_IXR_FRAMING | CDNS_UART_IXR_OVERRUN;
mode_reg = cdns_uart_readl(CDNS_UART_MR_OFFSET);
/* Handling Data Size */
switch (termios->c_cflag & CSIZE) {
case CS6:
cval |= CDNS_UART_MR_CHARLEN_6_BIT;
break;
case CS7:
cval |= CDNS_UART_MR_CHARLEN_7_BIT;
break;
default:
case CS8:
cval |= CDNS_UART_MR_CHARLEN_8_BIT;
termios->c_cflag &= ~CSIZE;
termios->c_cflag |= CS8;
break;
}
/* Handling Parity and Stop Bits length */
if (termios->c_cflag & CSTOPB)
cval |= CDNS_UART_MR_STOPMODE_2_BIT; /* 2 STOP bits */
else
cval |= CDNS_UART_MR_STOPMODE_1_BIT; /* 1 STOP bit */
if ((termios->c_cflag & PARENB) || (termios->c_cflag & PARODD)) {
/* Mark or Space parity */
if (termios->c_cflag & CMSPAR) {
if (termios->c_cflag & PARODD)
cval |= CDNS_UART_MR_PARITY_MARK;
else
cval |= CDNS_UART_MR_PARITY_SPACE;
} else {
if (termios->c_cflag & PARODD)
cval |= CDNS_UART_MR_PARITY_ODD;
else
cval |= CDNS_UART_MR_PARITY_EVEN;
}
} else {
cval |= CDNS_UART_MR_PARITY_NONE;
}
cval |= mode_reg & 1;
cdns_uart_writel(cval, CDNS_UART_MR_OFFSET);
spin_unlock_irqrestore(&port->lock, flags);
}
static void
serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
struct uart_omap_port *up = (struct uart_omap_port *)port;
unsigned char cval = 0;
unsigned long flags = 0;
unsigned int baud, quot;
unsigned int status;
switch (termios->c_cflag & CSIZE) {
case CS5:
cval = UART_LCR_WLEN5;
break;
case CS6:
cval = UART_LCR_WLEN6;
break;
case CS7:
cval = UART_LCR_WLEN7;
break;
default:
case CS8:
cval = UART_LCR_WLEN8;
break;
}
if (termios->c_cflag & CSTOPB)
cval |= UART_LCR_STOP;
if (termios->c_cflag & PARENB)
cval |= UART_LCR_PARITY;
if (!(termios->c_cflag & PARODD))
cval |= UART_LCR_EPAR;
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/13);
quot = serial_omap_get_divisor(port, baud);
up->dll = quot & 0xff;
up->dlh = quot >> 8;
up->mdr1 = UART_OMAP_MDR1_DISABLE;
up->fcr = UART_FCR_R_TRIG_01 | UART_FCR_T_TRIG_01 |
UART_FCR_ENABLE_FIFO;
if (up->use_dma)
up->fcr |= UART_FCR_DMA_SELECT;
/*
* Ok, we're now changing the port state. Do it with
* interrupts disabled.
*/
serial_omap_port_enable(up);
spin_lock_irqsave(&up->port.lock, flags);
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
if (termios->c_iflag & INPCK)
up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
if (termios->c_iflag & (BRKINT | PARMRK))
up->port.read_status_mask |= UART_LSR_BI;
/*
* Characters to ignore
*/
up->port.ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
if (termios->c_iflag & IGNBRK) {
up->port.ignore_status_mask |= UART_LSR_BI;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_OE;
}
/*
* ignore all characters if CREAD is not set
*/
if ((termios->c_cflag & CREAD) == 0)
up->port.ignore_status_mask |= UART_LSR_DR;
/*
* Modem status interrupts
*/
up->ier &= ~UART_IER_MSI;
//if (UART_ENABLE_MS(&up->port, termios->c_cflag))
if (UART_ENABLE_MS(&up->port, termios->c_cflag)) {
status = serial_in(up, UART_MSR);
if (status & UART_MSR_CTS)
uart_handle_cts_change(&up->port, status & UART_MSR_CTS);
up->ier |= UART_IER_MSI;
}
serial_out(up, UART_IER, up->ier);
serial_out(up, UART_LCR, cval); /* reset DLAB */
up->lcr = cval;
up->scr = OMAP_UART_SCR_TX_EMPTY;
/* FIFOs and DMA Settings */
/* FCR can be changed only when the
* baud clock is not running
* DLL_REG and DLH_REG set to 0.
*/
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
serial_out(up, UART_DLL, 0);
serial_out(up, UART_DLM, 0);
serial_out(up, UART_LCR, 0);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
up->efr = serial_in(up, UART_EFR);
serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
up->mcr = serial_in(up, UART_MCR);
serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
/* FIFO ENABLE, DMA MODE */
serial_out(up, UART_FCR, up->fcr);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
if (up->use_dma) {
if (up->errata & OMAP4_UART_ERRATA_i659_TX_THR) {
serial_out(up, UART_MDR3, SET_DMA_TX_THRESHOLD);
serial_out(up, UART_TX_DMA_THRESHOLD, TX_FIFO_THR_LVL);
}
serial_out(up, UART_TI752_TLR, 0);
up->scr |= (UART_FCR_TRIGGER_4 | UART_FCR_TRIGGER_8);
}
serial_out(up, UART_OMAP_SCR, up->scr);
serial_out(up, UART_EFR, up->efr);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
serial_out(up, UART_MCR, up->mcr);
/* Protocol, Baud Rate, and Interrupt Settings */
if (up->errata & UART_ERRATA_i202_MDR1_ACCESS)
omap_uart_mdr1_errataset(up, up->mdr1);
else
serial_out(up, UART_OMAP_MDR1, up->mdr1);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
up->efr = serial_in(up, UART_EFR);
serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
serial_out(up, UART_LCR, 0);
serial_out(up, UART_IER, 0);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
serial_out(up, UART_DLL, up->dll); /* LS of divisor */
serial_out(up, UART_DLM, up->dlh); /* MS of divisor */
serial_out(up, UART_LCR, 0);
serial_out(up, UART_IER, up->ier);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
serial_out(up, UART_EFR, up->efr);
serial_out(up, UART_LCR, cval);
if (baud > 230400 && baud != 3000000)
up->mdr1 = UART_OMAP_MDR1_13X_MODE;
else
up->mdr1 = UART_OMAP_MDR1_16X_MODE;
if (up->errata & UART_ERRATA_i202_MDR1_ACCESS)
omap_uart_mdr1_errataset(up, up->mdr1);
else
serial_out(up, UART_OMAP_MDR1, up->mdr1);
/* Hardware Flow Control Configuration */
if (termios->c_cflag & CRTSCTS) {
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
up->mcr = serial_in(up, UART_MCR);
serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
up->efr = serial_in(up, UART_EFR);
serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
serial_out(up, UART_TI752_TCR, OMAP_UART_TCR_TRIG);
up->efr |= (UART_EFR_CTS | UART_EFR_RTS);
serial_out(up, UART_EFR, up->efr); /* Enable AUTORTS and AUTOCTS */
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
up->mcr |= UART_MCR_RTS;
serial_out(up, UART_MCR, up->mcr);
serial_out(up, UART_LCR, cval);
} else {
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
up->efr = serial_in(up, UART_EFR);
up->efr &= ~(UART_EFR_CTS | UART_EFR_RTS);
serial_out(up, UART_EFR, up->efr); /* Disable AUTORTS and AUTOCTS */
serial_out(up, UART_LCR, cval);
}
serial_omap_set_mctrl(&up->port, up->port.mctrl);
/* Software Flow Control Configuration */
serial_omap_configure_xonxoff(up, termios);
/* Now we are ready for RX data: enable rts line */
if (up->rts_mux_driver_control && up->rts_pullup_in_suspend) {
omap_rts_mux_write(0, up->port.line);
up->rts_pullup_in_suspend = 0;
}
spin_unlock_irqrestore(&up->port.lock, flags);
serial_omap_port_disable(up);
dev_dbg(up->port.dev, "serial_omap_set_termios+%d\n", up->pdev->id);
}
static void tegra_uart_set_termios(struct uart_port *u,
struct ktermios *termios, struct ktermios *oldtermios)
{
struct tegra_uart_port *tup = to_tegra_uport(u);
unsigned int baud;
unsigned long flags;
unsigned int lcr;
int symb_bit = 1;
struct clk *parent_clk = clk_get_parent(tup->uart_clk);
unsigned long parent_clk_rate = clk_get_rate(parent_clk);
int max_divider = (tup->cdata->support_clk_src_div) ? 0x7FFF : 0xFFFF;
max_divider *= 16;
spin_lock_irqsave(&u->lock, flags);
/* Changing configuration, it is safe to stop any rx now */
if (tup->rts_active)
set_rts(tup, false);
/* Clear all interrupts as configuration is going to be change */
tegra_uart_write(tup, tup->ier_shadow | UART_IER_RDI, UART_IER);
tegra_uart_read(tup, UART_IER);
tegra_uart_write(tup, 0, UART_IER);
tegra_uart_read(tup, UART_IER);
/* Parity */
lcr = tup->lcr_shadow;
lcr &= ~UART_LCR_PARITY;
/* CMSPAR isn't supported by this driver */
termios->c_cflag &= ~CMSPAR;
if ((termios->c_cflag & PARENB) == PARENB) {
symb_bit++;
if (termios->c_cflag & PARODD) {
lcr |= UART_LCR_PARITY;
lcr &= ~UART_LCR_EPAR;
lcr &= ~UART_LCR_SPAR;
} else {
lcr |= UART_LCR_PARITY;
lcr |= UART_LCR_EPAR;
lcr &= ~UART_LCR_SPAR;
}
}
lcr &= ~UART_LCR_WLEN8;
switch (termios->c_cflag & CSIZE) {
case CS5:
lcr |= UART_LCR_WLEN5;
symb_bit += 5;
break;
case CS6:
lcr |= UART_LCR_WLEN6;
symb_bit += 6;
break;
case CS7:
lcr |= UART_LCR_WLEN7;
symb_bit += 7;
break;
default:
lcr |= UART_LCR_WLEN8;
symb_bit += 8;
break;
}
/* Stop bits */
if (termios->c_cflag & CSTOPB) {
lcr |= UART_LCR_STOP;
symb_bit += 2;
} else {
lcr &= ~UART_LCR_STOP;
symb_bit++;
}
tegra_uart_write(tup, lcr, UART_LCR);
tup->lcr_shadow = lcr;
tup->symb_bit = symb_bit;
/* Baud rate. */
baud = uart_get_baud_rate(u, termios, oldtermios,
parent_clk_rate/max_divider,
parent_clk_rate/16);
spin_unlock_irqrestore(&u->lock, flags);
tegra_set_baudrate(tup, baud);
if (tty_termios_baud_rate(termios))
tty_termios_encode_baud_rate(termios, baud, baud);
spin_lock_irqsave(&u->lock, flags);
/* Flow control */
if (termios->c_cflag & CRTSCTS) {
tup->mcr_shadow |= TEGRA_UART_MCR_CTS_EN;
tup->mcr_shadow &= ~TEGRA_UART_MCR_RTS_EN;
tegra_uart_write(tup, tup->mcr_shadow, UART_MCR);
/* if top layer has asked to set rts active then do so here */
if (tup->rts_active)
set_rts(tup, true);
} else {
tup->mcr_shadow &= ~TEGRA_UART_MCR_CTS_EN;
tup->mcr_shadow &= ~TEGRA_UART_MCR_RTS_EN;
tegra_uart_write(tup, tup->mcr_shadow, UART_MCR);
}
/* update the port timeout based on new settings */
uart_update_timeout(u, termios->c_cflag, baud);
/* Make sure all write has completed */
tegra_uart_read(tup, UART_IER);
/* Reenable interrupt */
tegra_uart_write(tup, tup->ier_shadow, UART_IER);
tegra_uart_read(tup, UART_IER);
spin_unlock_irqrestore(&u->lock, flags);
return;
}
static void msm_hsl_set_termios(struct uart_port *port,
struct ktermios *termios,
struct ktermios *old)
{
unsigned long flags;
unsigned int baud, mr;
spin_lock_irqsave(&port->lock, flags);
clk_en(port, 1);
/* calculate and set baud rate */
baud = uart_get_baud_rate(port, termios, old, 300, 460800);
msm_hsl_set_baud_rate(port, baud);
/* calculate parity */
mr = msm_hsl_read(port, UARTDM_MR2_ADDR);
mr &= ~UARTDM_MR2_PARITY_MODE_BMSK;
if (termios->c_cflag & PARENB) {
if (termios->c_cflag & PARODD)
mr |= ODD_PARITY;
else if (termios->c_cflag & CMSPAR)
mr |= SPACE_PARITY;
else
mr |= EVEN_PARITY;
}
/* calculate bits per char */
mr &= ~UARTDM_MR2_BITS_PER_CHAR_BMSK;
switch (termios->c_cflag & CSIZE) {
case CS5:
mr |= FIVE_BPC;
break;
case CS6:
mr |= SIX_BPC;
break;
case CS7:
mr |= SEVEN_BPC;
break;
case CS8:
default:
mr |= EIGHT_BPC;
break;
}
/* calculate stop bits */
mr &= ~(STOP_BIT_ONE | STOP_BIT_TWO);
if (termios->c_cflag & CSTOPB)
mr |= STOP_BIT_TWO;
else
mr |= STOP_BIT_ONE;
/* set parity, bits per char, and stop bit */
msm_hsl_write(port, mr, UARTDM_MR2_ADDR);
/* calculate and set hardware flow control */
mr = msm_hsl_read(port, UARTDM_MR1_ADDR);
mr &= ~(UARTDM_MR1_CTS_CTL_BMSK | UARTDM_MR1_RX_RDY_CTL_BMSK);
if (termios->c_cflag & CRTSCTS) {
mr |= UARTDM_MR1_CTS_CTL_BMSK;
mr |= UARTDM_MR1_RX_RDY_CTL_BMSK;
}
msm_hsl_write(port, mr, UARTDM_MR1_ADDR);
/* Configure status bits to ignore based on termio flags. */
port->read_status_mask = 0;
if (termios->c_iflag & INPCK)
port->read_status_mask |= UARTDM_SR_PAR_FRAME_BMSK;
if (termios->c_iflag & (BRKINT | PARMRK))
port->read_status_mask |= UARTDM_SR_RX_BREAK_BMSK;
uart_update_timeout(port, termios->c_cflag, baud);
clk_en(port, 0);
spin_unlock_irqrestore(&port->lock, flags);
}
static void vt8500_set_termios(struct uart_port *port,
struct ktermios *termios,
struct ktermios *old)
{
struct vt8500_port *vt8500_port =
container_of(port, struct vt8500_port, uart);
unsigned long flags;
unsigned int baud, lcr;
unsigned int loops = 1000;
spin_lock_irqsave(&port->lock, flags);
/* calculate and set baud rate */
baud = uart_get_baud_rate(port, termios, old, 900, 921600);
baud = vt8500_set_baud_rate(port, baud);
if (tty_termios_baud_rate(termios))
tty_termios_encode_baud_rate(termios, baud, baud);
/* calculate parity */
lcr = vt8500_read(&vt8500_port->uart, VT8500_URLCR);
lcr &= ~(VT8500_PARENB | VT8500_PARODD);
if (termios->c_cflag & PARENB) {
lcr |= VT8500_PARENB;
termios->c_cflag &= ~CMSPAR;
if (termios->c_cflag & PARODD)
lcr |= VT8500_PARODD;
}
/* calculate bits per char */
lcr &= ~VT8500_CS8;
switch (termios->c_cflag & CSIZE) {
case CS7:
break;
case CS8:
default:
lcr |= VT8500_CS8;
termios->c_cflag &= ~CSIZE;
termios->c_cflag |= CS8;
break;
}
/* calculate stop bits */
lcr &= ~VT8500_CSTOPB;
if (termios->c_cflag & CSTOPB)
lcr |= VT8500_CSTOPB;
lcr &= ~VT8500_SWRTSCTS;
if (vt8500_port->vt8500_uart_flags & VT8500_HAS_SWRTSCTS_SWITCH)
lcr |= VT8500_SWRTSCTS;
/* set parity, bits per char, and stop bit */
vt8500_write(&vt8500_port->uart, lcr, VT8500_URLCR);
/* Configure status bits to ignore based on termio flags. */
port->read_status_mask = 0;
if (termios->c_iflag & IGNPAR)
port->read_status_mask = FER | PER;
uart_update_timeout(port, termios->c_cflag, baud);
/* Reset FIFOs */
vt8500_write(&vt8500_port->uart, 0x88c, VT8500_URFCR);
while ((vt8500_read(&vt8500_port->uart, VT8500_URFCR) & 0xc)
&& --loops)
cpu_relax();
/* Every possible FIFO-related interrupt */
vt8500_port->ier = RX_FIFO_INTS | TX_FIFO_INTS;
/*
* CTS flow control
*/
if (UART_ENABLE_MS(&vt8500_port->uart, termios->c_cflag))
vt8500_port->ier |= TCTS;
vt8500_write(&vt8500_port->uart, 0x881, VT8500_URFCR);
vt8500_write(&vt8500_port->uart, vt8500_port->ier, VT8500_URIER);
spin_unlock_irqrestore(&port->lock, flags);
}
static void sc26xx_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
unsigned int baud = uart_get_baud_rate(port, termios, old, 0, 4000000);
unsigned int quot = uart_get_divisor(port, baud);
unsigned int iflag, cflag;
unsigned long flags;
u8 mr1, mr2, csr;
spin_lock_irqsave(&port->lock, flags);
while ((READ_SC_PORT(port, SR) & ((1 << 3) | (1 << 2))) != 0xc)
udelay(2);
WRITE_SC_PORT(port, CR, CR_DIS_TX | CR_DIS_RX);
iflag = termios->c_iflag;
cflag = termios->c_cflag;
port->read_status_mask = SR_OVERRUN;
if (iflag & INPCK)
port->read_status_mask |= SR_PARITY | SR_FRAME;
if (iflag & (BRKINT | PARMRK))
port->read_status_mask |= SR_BREAK;
port->ignore_status_mask = 0;
if (iflag & IGNBRK)
port->ignore_status_mask |= SR_BREAK;
if ((cflag & CREAD) == 0)
port->ignore_status_mask |= SR_BREAK | SR_FRAME |
SR_PARITY | SR_OVERRUN;
switch (cflag & CSIZE) {
case CS5:
mr1 = 0x00;
break;
case CS6:
mr1 = 0x01;
break;
case CS7:
mr1 = 0x02;
break;
default:
case CS8:
mr1 = 0x03;
break;
}
mr2 = 0x07;
if (cflag & CSTOPB)
mr2 = 0x0f;
if (cflag & PARENB) {
if (cflag & PARODD)
mr1 |= (1 << 2);
} else
mr1 |= (2 << 3);
switch (baud) {
case 50:
csr = 0x00;
break;
case 110:
csr = 0x11;
break;
case 134:
csr = 0x22;
break;
case 200:
csr = 0x33;
break;
case 300:
csr = 0x44;
break;
case 600:
csr = 0x55;
break;
case 1200:
csr = 0x66;
break;
case 2400:
csr = 0x88;
break;
case 4800:
csr = 0x99;
break;
default:
case 9600:
csr = 0xbb;
break;
case 19200:
csr = 0xcc;
break;
}
WRITE_SC_PORT(port, CR, CR_RES_MR);
WRITE_SC_PORT(port, MRx, mr1);
WRITE_SC_PORT(port, MRx, mr2);
WRITE_SC(port, ACR, 0x80);
WRITE_SC_PORT(port, CSR, csr);
WRITE_SC_PORT(port, CR, CR_RES_RX);
WRITE_SC_PORT(port, CR, CR_RES_TX);
WRITE_SC_PORT(port, CR, CR_ENA_TX | CR_ENA_RX);
while ((READ_SC_PORT(port, SR) & ((1 << 3) | (1 << 2))) != 0xc)
udelay(2);
uart_update_timeout(port, cflag,
(port->uartclk / (16 * quot)));
spin_unlock_irqrestore(&port->lock, flags);
}
static void
serial_m3110_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
struct uart_max3110 *max =
container_of(port, struct uart_max3110, port);
unsigned char cval;
unsigned int baud, parity = 0;
int clk_div = -1;
u16 new_conf = max->cur_conf;
switch (termios->c_cflag & CSIZE) {
case CS7:
cval = UART_LCR_WLEN7;
new_conf |= WC_7BIT_WORD;
break;
default:
/* We only support CS7 & CS8 */
termios->c_cflag &= ~CSIZE;
termios->c_cflag |= CS8;
case CS8:
cval = UART_LCR_WLEN8;
new_conf |= WC_8BIT_WORD;
break;
}
baud = uart_get_baud_rate(port, termios, old, 0, 230400);
/* First calc the div for 1.8MHZ clock case */
switch (baud) {
case 300:
clk_div = WC_BAUD_DR384;
break;
case 600:
clk_div = WC_BAUD_DR192;
break;
case 1200:
clk_div = WC_BAUD_DR96;
break;
case 2400:
clk_div = WC_BAUD_DR48;
break;
case 4800:
clk_div = WC_BAUD_DR24;
break;
case 9600:
clk_div = WC_BAUD_DR12;
break;
case 19200:
clk_div = WC_BAUD_DR6;
break;
case 38400:
clk_div = WC_BAUD_DR3;
break;
case 57600:
clk_div = WC_BAUD_DR2;
break;
case 115200:
clk_div = WC_BAUD_DR1;
break;
case 230400:
if (max->clock & MAX3110_HIGH_CLK)
break;
default:
/* Pick the previous baud rate */
baud = max->baud;
clk_div = max->cur_conf & WC_BAUD_DIV_MASK;
tty_termios_encode_baud_rate(termios, baud, baud);
}
if (max->clock & MAX3110_HIGH_CLK) {
clk_div += 1;
/* High clk version max3110 doesn't support B300 */
if (baud == 300) {
baud = 600;
clk_div = WC_BAUD_DR384;
}
if (baud == 230400)
clk_div = WC_BAUD_DR1;
tty_termios_encode_baud_rate(termios, baud, baud);
}
new_conf = (new_conf & ~WC_BAUD_DIV_MASK) | clk_div;
if (unlikely(termios->c_cflag & CMSPAR))
termios->c_cflag &= ~CMSPAR;
if (termios->c_cflag & CSTOPB)
new_conf |= WC_2_STOPBITS;
else
new_conf &= ~WC_2_STOPBITS;
if (termios->c_cflag & PARENB) {
new_conf |= WC_PARITY_ENABLE;
parity |= UART_LCR_PARITY;
} else
new_conf &= ~WC_PARITY_ENABLE;
if (!(termios->c_cflag & PARODD))
parity |= UART_LCR_EPAR;
max->parity = parity;
uart_update_timeout(port, termios->c_cflag, baud);
new_conf |= WC_TAG;
if (new_conf != max->cur_conf) {
if (!max3110_out(max, new_conf)) {
max->cur_conf = new_conf;
max->baud = baud;
}
}
}
static void
serial_pxa_set_termios(struct uart_port *port, struct termios *termios,
struct termios *old)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
unsigned char cval, fcr = 0;
unsigned long flags;
unsigned int baud, quot;
switch (termios->c_cflag & CSIZE) {
case CS5:
cval = UART_LCR_WLEN5;
break;
case CS6:
cval = UART_LCR_WLEN6;
break;
case CS7:
cval = UART_LCR_WLEN7;
break;
default:
case CS8:
cval = UART_LCR_WLEN8;
break;
}
if (termios->c_cflag & CSTOPB)
cval |= UART_LCR_STOP;
if (termios->c_cflag & PARENB)
cval |= UART_LCR_PARITY;
if (!(termios->c_cflag & PARODD))
cval |= UART_LCR_EPAR;
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
quot = uart_get_divisor(port, baud);
if ((up->port.uartclk / quot) < (2400 * 16))
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_PXAR1;
else if ((up->port.uartclk / quot) < (230400 * 16))
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_PXAR8;
else
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_PXAR32;
/*
* Ok, we're now changing the port state. Do it with
* interrupts disabled.
*/
spin_lock_irqsave(&up->port.lock, flags);
/*
* Ensure the port will be enabled.
* This is required especially for serial console.
*/
up->ier |= IER_UUE;
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
if (termios->c_iflag & INPCK)
up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
if (termios->c_iflag & (BRKINT | PARMRK))
up->port.read_status_mask |= UART_LSR_BI;
/*
* Characters to ignore
*/
up->port.ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
if (termios->c_iflag & IGNBRK) {
up->port.ignore_status_mask |= UART_LSR_BI;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_OE;
}
/*
* ignore all characters if CREAD is not set
*/
if ((termios->c_cflag & CREAD) == 0)
up->port.ignore_status_mask |= UART_LSR_DR;
/*
* CTS flow control flag and modem status interrupts
*/
up->ier &= ~UART_IER_MSI;
if (UART_ENABLE_MS(&up->port, termios->c_cflag))
up->ier |= UART_IER_MSI;
serial_out(up, UART_IER, up->ier);
serial_out(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */
serial_out(up, UART_DLL, quot & 0xff); /* LS of divisor */
serial_out(up, UART_DLM, quot >> 8); /* MS of divisor */
serial_out(up, UART_LCR, cval); /* reset DLAB */
up->lcr = cval; /* Save LCR */
serial_pxa_set_mctrl(&up->port, up->port.mctrl);
serial_out(up, UART_FCR, fcr);
spin_unlock_irqrestore(&up->port.lock, flags);
}
static void
serial_pxa_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
unsigned char cval, fcr = 0;
unsigned long flags;
unsigned int baud, quot = 0;
unsigned int dll;
switch (termios->c_cflag & CSIZE) {
case CS5:
cval = UART_LCR_WLEN5;
break;
case CS6:
cval = UART_LCR_WLEN6;
break;
case CS7:
cval = UART_LCR_WLEN7;
break;
default:
case CS8:
cval = UART_LCR_WLEN8;
break;
}
if (termios->c_cflag & CSTOPB)
cval |= UART_LCR_STOP;
if (termios->c_cflag & PARENB)
cval |= UART_LCR_PARITY;
if (!(termios->c_cflag & PARODD))
cval |= UART_LCR_EPAR;
/*
* Ask the core to calculate the divisor for us.
*/
baud = uart_get_baud_rate(port, termios, old, 0, 921600*16*4/16);
if (baud > 921600) {
port->uartclk = 921600*16*4; /* 58.9823MHz as the clk src */
if (B1500000 == (termios->c_cflag & B1500000))
quot = 2;
if (B3500000 == (termios->c_cflag & B3500000))
quot = 1;
if (quot == 0)
quot = uart_get_divisor(port, baud);
} else {
quot = uart_get_divisor(port, baud);
}
if (up->dma_enable) {
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_PXAR32 |
UART_FCR_PXA_TRAIL;
fcr &= ~UART_FCR_PXA_BUS32;
} else {
if ((up->port.uartclk / quot) < (2400 * 16))
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_PXAR1;
else if ((up->port.uartclk / quot) < (230400 * 16))
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_PXAR8;
else
fcr = UART_FCR_ENABLE_FIFO | UART_FCR_PXAR32;
}
/*
* Ok, we're now changing the port state. Do it with
* interrupts disabled.
*/
spin_lock_irqsave(&up->port.lock, flags);
if (baud > 921600)
up->ier |= UART_IER_HSE;
else
up->ier &= ~UART_IER_HSE;
/*
* Ensure the port will be enabled.
* This is required especially for serial console.
*/
up->ier |= UART_IER_UUE;
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
if (termios->c_iflag & INPCK)
up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
if (termios->c_iflag & (BRKINT | PARMRK))
up->port.read_status_mask |= UART_LSR_BI;
/*
* Characters to ignore
*/
up->port.ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
if (termios->c_iflag & IGNBRK) {
up->port.ignore_status_mask |= UART_LSR_BI;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_OE;
}
/*
* ignore all characters if CREAD is not set
*/
if ((termios->c_cflag & CREAD) == 0)
up->port.ignore_status_mask |= UART_LSR_DR;
/*
* CTS flow control flag and modem status interrupts
*/
if (!up->dma_enable) {
/* Don't enable modem status interrupt if DMA is enabled.
* Inherited from the old code.
* Please also refer to serial_pxa_enable_ms().
*/
up->ier &= ~UART_IER_MSI;
if (UART_ENABLE_MS(&up->port, termios->c_cflag))
up->ier |= UART_IER_MSI;
}
serial_out(up, UART_IER, up->ier);
if (termios->c_cflag & CRTSCTS)
up->mcr |= UART_MCR_AFE;
else
up->mcr &= ~UART_MCR_AFE;
serial_out(up, UART_LCR, cval | UART_LCR_DLAB); /* set DLAB */
serial_out(up, UART_DLL, quot & 0xff); /* LS of divisor */
/*
* work around Errata #75 according to Intel(R) PXA27x Processor Family
* Specification Update (Nov 2005)
*/
dll = serial_in(up, UART_DLL);
WARN_ON(dll != (quot & 0xff));
serial_out(up, UART_DLM, quot >> 8); /* MS of divisor */
serial_out(up, UART_LCR, cval); /* reset DLAB */
up->lcr = cval; /* Save LCR */
serial_pxa_set_mctrl(&up->port, up->port.mctrl);
serial_out(up, UART_FCR, fcr);
spin_unlock_irqrestore(&up->port.lock, flags);
}
static void sirfsoc_uart_set_termios(struct uart_port *port,
struct ktermios *termios,
struct ktermios *old)
{
struct sirfsoc_uart_port *sirfport = to_sirfport(port);
struct sirfsoc_register *ureg = &sirfport->uart_reg->uart_reg;
struct sirfsoc_int_en *uint_en = &sirfport->uart_reg->uart_int_en;
unsigned long config_reg = 0;
unsigned long baud_rate;
unsigned long set_baud;
unsigned long flags;
unsigned long ic;
unsigned int clk_div_reg = 0;
unsigned long txfifo_op_reg, ioclk_rate;
unsigned long rx_time_out;
int threshold_div;
u32 data_bit_len, stop_bit_len, len_val;
unsigned long sample_div_reg = 0xf;
ioclk_rate = port->uartclk;
switch (termios->c_cflag & CSIZE) {
default:
case CS8:
data_bit_len = 8;
config_reg |= SIRFUART_DATA_BIT_LEN_8;
break;
case CS7:
data_bit_len = 7;
config_reg |= SIRFUART_DATA_BIT_LEN_7;
break;
case CS6:
data_bit_len = 6;
config_reg |= SIRFUART_DATA_BIT_LEN_6;
break;
case CS5:
data_bit_len = 5;
config_reg |= SIRFUART_DATA_BIT_LEN_5;
break;
}
if (termios->c_cflag & CSTOPB) {
config_reg |= SIRFUART_STOP_BIT_LEN_2;
stop_bit_len = 2;
} else
stop_bit_len = 1;
spin_lock_irqsave(&port->lock, flags);
port->read_status_mask = uint_en->sirfsoc_rx_oflow_en;
port->ignore_status_mask = 0;
if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) {
if (termios->c_iflag & INPCK)
port->read_status_mask |= uint_en->sirfsoc_frm_err_en |
uint_en->sirfsoc_parity_err_en;
} else {
if (termios->c_iflag & INPCK)
port->read_status_mask |= uint_en->sirfsoc_frm_err_en;
}
if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
port->read_status_mask |= uint_en->sirfsoc_rxd_brk_en;
if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) {
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |=
uint_en->sirfsoc_frm_err_en |
uint_en->sirfsoc_parity_err_en;
if (termios->c_cflag & PARENB) {
if (termios->c_cflag & CMSPAR) {
if (termios->c_cflag & PARODD)
config_reg |= SIRFUART_STICK_BIT_MARK;
else
config_reg |= SIRFUART_STICK_BIT_SPACE;
} else {
if (termios->c_cflag & PARODD)
config_reg |= SIRFUART_STICK_BIT_ODD;
else
config_reg |= SIRFUART_STICK_BIT_EVEN;
}
}
} else {
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |=
uint_en->sirfsoc_frm_err_en;
if (termios->c_cflag & PARENB)
dev_warn(port->dev,
"USP-UART not support parity err\n");
}
if (termios->c_iflag & IGNBRK) {
port->ignore_status_mask |=
uint_en->sirfsoc_rxd_brk_en;
if (termios->c_iflag & IGNPAR)
port->ignore_status_mask |=
uint_en->sirfsoc_rx_oflow_en;
}
if ((termios->c_cflag & CREAD) == 0)
port->ignore_status_mask |= SIRFUART_DUMMY_READ;
/* Hardware Flow Control Settings */
if (UART_ENABLE_MS(port, termios->c_cflag)) {
if (!sirfport->ms_enabled)
sirfsoc_uart_enable_ms(port);
} else {
if (sirfport->ms_enabled)
sirfsoc_uart_disable_ms(port);
}
baud_rate = uart_get_baud_rate(port, termios, old, 0, 4000000);
if (ioclk_rate == 150000000) {
for (ic = 0; ic < SIRF_BAUD_RATE_SUPPORT_NR; ic++)
if (baud_rate == baudrate_to_regv[ic].baud_rate)
clk_div_reg = baudrate_to_regv[ic].reg_val;
}
set_baud = baud_rate;
if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) {
if (unlikely(clk_div_reg == 0))
clk_div_reg = sirfsoc_uart_calc_sample_div(baud_rate,
ioclk_rate, &set_baud);
wr_regl(port, ureg->sirfsoc_divisor, clk_div_reg);
} else {
clk_div_reg = sirfsoc_usp_calc_sample_div(baud_rate,
ioclk_rate, &sample_div_reg);
sample_div_reg--;
set_baud = ((ioclk_rate / (clk_div_reg+1) - 1) /
(sample_div_reg + 1));
/* setting usp mode 2 */
len_val = ((1 << SIRFSOC_USP_MODE2_RXD_DELAY_OFFSET) |
(1 << SIRFSOC_USP_MODE2_TXD_DELAY_OFFSET));
len_val |= ((clk_div_reg & SIRFSOC_USP_MODE2_CLK_DIVISOR_MASK)
<< SIRFSOC_USP_MODE2_CLK_DIVISOR_OFFSET);
wr_regl(port, ureg->sirfsoc_mode2, len_val);
}
if (tty_termios_baud_rate(termios))
tty_termios_encode_baud_rate(termios, set_baud, set_baud);
/* set receive timeout && data bits len */
rx_time_out = SIRFSOC_UART_RX_TIMEOUT(set_baud, 20000);
rx_time_out = SIRFUART_RECV_TIMEOUT_VALUE(rx_time_out);
txfifo_op_reg = rd_regl(port, ureg->sirfsoc_tx_fifo_op);
wr_regl(port, ureg->sirfsoc_tx_fifo_op,
(txfifo_op_reg & ~SIRFUART_FIFO_START));
if (sirfport->uart_reg->uart_type == SIRF_REAL_UART) {
config_reg |= SIRFUART_UART_RECV_TIMEOUT(rx_time_out);
wr_regl(port, ureg->sirfsoc_line_ctrl, config_reg);
} else {
/*tx frame ctrl*/
len_val = (data_bit_len - 1) << SIRFSOC_USP_TX_DATA_LEN_OFFSET;
len_val |= (data_bit_len + 1 + stop_bit_len - 1) <<
SIRFSOC_USP_TX_FRAME_LEN_OFFSET;
len_val |= ((data_bit_len - 1) <<
SIRFSOC_USP_TX_SHIFTER_LEN_OFFSET);
len_val |= (((clk_div_reg & 0xc00) >> 10) <<
SIRFSOC_USP_TX_CLK_DIVISOR_OFFSET);
wr_regl(port, ureg->sirfsoc_tx_frame_ctrl, len_val);
/*rx frame ctrl*/
len_val = (data_bit_len - 1) << SIRFSOC_USP_RX_DATA_LEN_OFFSET;
len_val |= (data_bit_len + 1 + stop_bit_len - 1) <<
SIRFSOC_USP_RX_FRAME_LEN_OFFSET;
len_val |= (data_bit_len - 1) <<
SIRFSOC_USP_RX_SHIFTER_LEN_OFFSET;
len_val |= (((clk_div_reg & 0xf000) >> 12) <<
SIRFSOC_USP_RX_CLK_DIVISOR_OFFSET);
wr_regl(port, ureg->sirfsoc_rx_frame_ctrl, len_val);
/*async param*/
wr_regl(port, ureg->sirfsoc_async_param_reg,
(SIRFUART_USP_RECV_TIMEOUT(rx_time_out)) |
(sample_div_reg & SIRFSOC_USP_ASYNC_DIV2_MASK) <<
SIRFSOC_USP_ASYNC_DIV2_OFFSET);
}
if (sirfport->tx_dma_chan)
wr_regl(port, ureg->sirfsoc_tx_dma_io_ctrl, SIRFUART_DMA_MODE);
else
wr_regl(port, ureg->sirfsoc_tx_dma_io_ctrl, SIRFUART_IO_MODE);
if (sirfport->rx_dma_chan)
wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl,
rd_regl(port, ureg->sirfsoc_rx_dma_io_ctrl) &
~SIRFUART_IO_MODE);
else
wr_regl(port, ureg->sirfsoc_rx_dma_io_ctrl,
rd_regl(port, ureg->sirfsoc_rx_dma_io_ctrl) |
SIRFUART_IO_MODE);
sirfport->rx_period_time = 20000000;
/* Reset Rx/Tx FIFO Threshold level for proper baudrate */
if (set_baud < 1000000)
threshold_div = 1;
else
threshold_div = 2;
wr_regl(port, ureg->sirfsoc_tx_fifo_ctrl,
SIRFUART_FIFO_THD(port) / threshold_div);
wr_regl(port, ureg->sirfsoc_rx_fifo_ctrl,
SIRFUART_FIFO_THD(port) / threshold_div);
txfifo_op_reg |= SIRFUART_FIFO_START;
wr_regl(port, ureg->sirfsoc_tx_fifo_op, txfifo_op_reg);
uart_update_timeout(port, termios->c_cflag, set_baud);
wr_regl(port, ureg->sirfsoc_tx_rx_en, SIRFUART_TX_EN | SIRFUART_RX_EN);
spin_unlock_irqrestore(&port->lock, flags);
}
