int wl1271_boot(struct wl1271 *wl)
{
int ret = 0;
u32 tmp, clk, pause;
if (REF_CLOCK == 0 || REF_CLOCK == 2)
/* ref clk: 19.2/38.4 */
clk = 0x3;
else if (REF_CLOCK == 1 || REF_CLOCK == 3)
/* ref clk: 26/52 */
clk = 0x5;
wl1271_reg_write32(wl, PLL_PARAMETERS, clk);
pause = wl1271_reg_read32(wl, PLL_PARAMETERS);
wl1271_debug(DEBUG_BOOT, "pause1 0x%x", pause);
pause &= ~(WU_COUNTER_PAUSE_VAL); /* FIXME: This should probably be
* WU_COUNTER_PAUSE_VAL instead of
* 0x3ff (magic number ). How does
* this work?! */
pause |= WU_COUNTER_PAUSE_VAL;
wl1271_reg_write32(wl, WU_COUNTER_PAUSE, pause);
/* Continue the ELP wake up sequence */
wl1271_reg_write32(wl, WELP_ARM_COMMAND, WELP_ARM_COMMAND_VAL);
udelay(500);
wl1271_set_partition(wl,
part_table[PART_DRPW].mem.start,
part_table[PART_DRPW].mem.size,
part_table[PART_DRPW].reg.start,
part_table[PART_DRPW].reg.size);
/* Read-modify-write DRPW_SCRATCH_START register (see next state)
to be used by DRPw FW. The RTRIM value will be added by the FW
before taking DRPw out of reset */
wl1271_debug(DEBUG_BOOT, "DRPW_SCRATCH_START %08x", DRPW_SCRATCH_START);
clk = wl1271_reg_read32(wl, DRPW_SCRATCH_START);
wl1271_debug(DEBUG_BOOT, "clk2 0x%x", clk);
/* 2 */
clk |= (REF_CLOCK << 1) << 4;
wl1271_reg_write32(wl, DRPW_SCRATCH_START, clk);
wl1271_set_partition(wl,
part_table[PART_WORK].mem.start,
part_table[PART_WORK].mem.size,
part_table[PART_WORK].reg.start,
part_table[PART_WORK].reg.size);
/* Disable interrupts */
wl1271_reg_write32(wl, ACX_REG_INTERRUPT_MASK, WL1271_ACX_INTR_ALL);
ret = wl1271_boot_soft_reset(wl);
if (ret < 0)
goto out;
/* 2. start processing NVS file */
ret = wl1271_boot_upload_nvs(wl);
if (ret < 0)
goto out;
/* write firmware's last address (ie. it's length) to
* ACX_EEPROMLESS_IND_REG */
wl1271_debug(DEBUG_BOOT, "ACX_EEPROMLESS_IND_REG");
wl1271_reg_write32(wl, ACX_EEPROMLESS_IND_REG, ACX_EEPROMLESS_IND_REG);
tmp = wl1271_reg_read32(wl, CHIP_ID_B);
wl1271_debug(DEBUG_BOOT, "chip id 0x%x", tmp);
/* 6. read the EEPROM parameters */
tmp = wl1271_reg_read32(wl, SCR_PAD2);
ret = wl1271_boot_write_irq_polarity(wl);
if (ret < 0)
goto out;
/* FIXME: Need to check whether this is really what we want */
wl1271_reg_write32(wl, ACX_REG_INTERRUPT_MASK,
WL1271_ACX_ALL_EVENTS_VECTOR);
/* WL1271: The reference driver skips steps 7 to 10 (jumps directly
* to upload_fw) */
ret = wl1271_boot_upload_firmware(wl);
if (ret < 0)
goto out;
/* 10.5 start firmware */
ret = wl1271_boot_run_firmware(wl);
if (ret < 0)
goto out;
/* set the wl1271 default filters */
wl->rx_config = WL1271_DEFAULT_RX_CONFIG;
wl->rx_filter = WL1271_DEFAULT_RX_FILTER;
wl1271_event_mbox_config(wl);
out:
return ret;
}
/* uploads NVS and firmware */
int wl1271_load_firmware(struct wl1271 *wl)
{
int ret = 0;
u32 tmp, clk;
int selected_clock = -1;
ret = wl12xx_init_pll_clock(wl, &selected_clock);
if (ret < 0)
goto out;
ret = wl1271_set_partition(wl, &wl12xx_part_table[PART_DRPW]);
if (ret < 0)
goto out;
/* Read-modify-write DRPW_SCRATCH_START register (see next state)
to be used by DRPw FW. The RTRIM value will be added by the FW
before taking DRPw out of reset */
wl1271_debug(DEBUG_BOOT, "DRPW_SCRATCH_START %08x", DRPW_SCRATCH_START);
ret = wl1271_read32(wl, DRPW_SCRATCH_START, &clk);
if (ret < 0)
goto out;
wl1271_debug(DEBUG_BOOT, "clk2 0x%x", clk);
if (wl->chip.id == CHIP_ID_1283_PG20) {
clk |= ((selected_clock & 0x3) << 1) << 4;
} else {
clk |= (wl->ref_clock << 1) << 4;
}
ret = wl1271_write32(wl, DRPW_SCRATCH_START, clk);
if (ret < 0)
goto out;
ret = wl1271_set_partition(wl, &wl12xx_part_table[PART_WORK]);
if (ret < 0)
goto out;
/* Disable interrupts */
ret = wl1271_write32(wl, ACX_REG_INTERRUPT_MASK, WL1271_ACX_INTR_ALL);
if (ret < 0)
goto out;
ret = wl1271_boot_soft_reset(wl);
if (ret < 0)
goto out;
/* 2. start processing NVS file */
ret = wl1271_boot_upload_nvs(wl);
if (ret < 0)
goto out;
/* write firmware's last address (ie. it's length) to
* ACX_EEPROMLESS_IND_REG */
wl1271_debug(DEBUG_BOOT, "ACX_EEPROMLESS_IND_REG");
ret = wl1271_write32(wl, ACX_EEPROMLESS_IND_REG,
ACX_EEPROMLESS_IND_REG);
if (ret < 0)
goto out;
ret = wl1271_read32(wl, CHIP_ID_B, &tmp);
if (ret < 0)
goto out;
wl1271_debug(DEBUG_BOOT, "chip id 0x%x", tmp);
/* 6. read the EEPROM parameters */
ret = wl1271_read32(wl, SCR_PAD2, &tmp);
if (ret < 0)
goto out;
/* WL1271: The reference driver skips steps 7 to 10 (jumps directly
* to upload_fw) */
if (wl->chip.id == CHIP_ID_1283_PG20) {
ret = wl1271_top_reg_write(wl, SDIO_IO_DS, wl->conf.hci_io_ds);
if (ret < 0)
goto out;
}
ret = wl1271_boot_upload_firmware(wl);
if (ret < 0)
goto out;
/* update loaded fw type */
wl->fw_type = wl->saved_fw_type;
out:
return ret;
}
