Exemple #1
0
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	u32 val;

	post_code(0x30);
	agesawrapper_amdinitmmio();
	post_code(0x31);

	/* Halt if there was a built in self test failure */
	post_code(0x33);
	report_bist_failure(bist);

	sb7xx_51xx_enable_wideio(0, 0x1600); /* though UARTs are on the NUVOTON BMC */
	wpcm450_enable_dev(WPCM450_SP1, SIO_PORT, CONFIG_TTYS0_BASE);
	sb7xx_51xx_disable_wideio(0);
	post_code(0x34);

	post_code(0x35);
	console_init();

	val = cpuid_eax(1);
	printk(BIOS_DEBUG, "BSP Family_Model: %08x \n", val);
	printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx \n", cpu_init_detectedx);

	post_code(0x37);
	val = agesawrapper_amdinitreset();
	if (val) {
		printk(BIOS_DEBUG, "agesawrapper_amdinitreset failed: %x \n", val);
	} else {
		printk(BIOS_DEBUG, "agesawrapper_amdinitreset passed\n");
	}

	if (!cpu_init_detectedx && boot_cpu()) {
		post_code(0x38);
		/*
		 * SR5650/5670/5690 RD890 chipset, read pci config space hang at POR,
		 * Disable all Pcie Bridges to work around It.
		 */
		sr56x0_rd890_disable_pcie_bridge();
		post_code(0x39);
		nb_Poweron_Init();
		post_code(0x3A);
		sb_Poweron_Init();
	}
	post_code(0x3B);
	val = agesawrapper_amdinitearly();
	if(val) {
		printk(BIOS_DEBUG, "agesawrapper_amdinitearly failed: %x \n", val);
	} else {
		printk(BIOS_DEBUG, "agesawrapper_amdinitearly passed\n");
	}

	post_code(0x3C);
	/* W83627DHG pin89,90 function select is RSTOUT3#, RSTOUT2# by default.
	 * In order to access W83795G/ADG HWM using I2C protocol,
	 * we select function to SDA, SCL function (or GP33, GP32 function).
	 */
	w83627dhg_enable_i2c(PNP_DEV(0x2E, W83627DHG_SPI));

	nb_Ht_Init();
	post_code(0x3D);
	/* Reset for HT, FIDVID, PLL and ucode patch(errata) changes to take affect. */
	if (!warm_reset_detect(0)) {
		print_info("...WARM RESET...\n\n\n");
		distinguish_cpu_resets(0);
		soft_reset();
		die("After soft_reset_x - shouldn't see this message!!!\n");
	}

	post_code(0x40);
	val = agesawrapper_amdinitpost();
	if (val) {
		printk(BIOS_DEBUG, "agesawrapper_amdinitpost failed: %x \n", val);
	} else {
		printk(BIOS_DEBUG, "agesawrapper_amdinitpost passed\n");
	}

	post_code(0x41);
	val = agesawrapper_amdinitenv();
	if(val) {
		printk(BIOS_DEBUG, "agesawrapper_amdinitenv failed: %x \n", val);
	}
	printk(BIOS_DEBUG, "agesawrapper_amdinitenv passed\n");

	post_code(0x42);

	post_code(0x50);
	print_debug("Disabling cache as ram ");
	disable_cache_as_ram();
	print_debug("done\n");

	post_code(0x51);
	copy_and_run();

	/* We will not return,  Should never see this message and post code. */
	print_debug("should not be here -\n");
	post_code(0x54);
}
Exemple #2
0
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	struct sys_info *sysinfo = &sysinfo_car;
	static const u8 spd_addr[] = {
				RC00, 0x52,  0x53,  0, 0, 0x50,  0x51,  0, 0,
				//RC00, DIMM2, DIMM3, 0, 0, DIMM0, DIMM1, 0, 0,
			};
	u32 bsp_apicid = 0;
	u32 val;
	msr_t msr;

	timestamp_init(timestamp_get());
	timestamp_add_now(TS_START_ROMSTAGE);

	if (!cpu_init_detectedx && boot_cpu()) {
		/* Nothing special needs to be done to find bus 0 */
		/* Allow the HT devices to be found */
		/* mov bsp to bus 0xff when > 8 nodes */
		set_bsp_node_CHtExtNodeCfgEn();
		enumerate_ht_chain();

		/* SR56x0 pcie bridges block pci_locate_device() before pcie training.
		 * disable all pcie bridges on SR56x0 to work around it
		 */
		sr5650_disable_pcie_bridge();
		sb7xx_51xx_lpc_port80();
	}

	post_code(0x30);

	if (bist == 0) {
		bsp_apicid = init_cpus(cpu_init_detectedx, sysinfo); /* mmconf is inited in init_cpus */
		/* All cores run this but the BSP(node0,core0) is the only core that returns. */
	}

	post_code(0x32);

	enable_sr5650_dev8();
	sb7xx_51xx_lpc_init();

	sb7xx_51xx_enable_wideio(0, 0x1600);

	wpcm450_enable_dev(WPCM450_SP1, 0x164E, CONFIG_TTYS0_BASE);

	sb7xx_51xx_disable_wideio(0);

	console_init();

//	dump_mem(CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE-0x200, CONFIG_DCACHE_RAM_BASE+CONFIG_DCACHE_RAM_SIZE);

	/* Halt if there was a built in self test failure */
	report_bist_failure(bist);

	// Load MPB
	val = cpuid_eax(1);
	printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
	printk(BIOS_DEBUG, "*sysinfo range: [%p,%p]\n",sysinfo,sysinfo+1);
	printk(BIOS_DEBUG, "bsp_apicid = %02x\n", bsp_apicid);
	printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);

	/* Setup sysinfo defaults */
	set_sysinfo_in_ram(0);

	update_microcode(val);

	post_code(0x33);

	cpuSetAMDMSR();
	post_code(0x34);

	/* TODO: The Kernel must support 12 processor, otherwise the interrupt
	 * can not work correctly. */
	amd_ht_init(sysinfo);
	post_code(0x35);

	/* Setup nodes PCI space and start core 0 AP init. */
	finalize_node_setup(sysinfo);

	/* Setup any mainboard PCI settings etc. */
	setup_mb_resource_map();
	post_code(0x36);

	/* wait for all the APs core0 started by finalize_node_setup. */
	/* FIXME: A bunch of cores are going to start output to serial at once.
	   It would be nice to fixup prink spinlocks for ROM XIP mode.
	   I think it could be done by putting the spinlock flag in the cache
	   of the BSP located right after sysinfo.
	 */
	wait_all_core0_started();

#if CONFIG_LOGICAL_CPUS
	/* Core0 on each node is configured. Now setup any additional cores. */
	printk(BIOS_DEBUG, "start_other_cores()\n");
	start_other_cores();
	post_code(0x37);
	wait_all_other_cores_started(bsp_apicid);
#endif

	post_code(0x38);

	/* run _early_setup before soft-reset. */
	sr5650_early_setup();
	sb7xx_51xx_early_setup();

#if CONFIG_SET_FIDVID
	msr = rdmsr(0xc0010071);
	printk(BIOS_DEBUG, "\nBegin FIDVID MSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo);

	/* FIXME: The sb fid change may survive the warm reset and only
	   need to be done once.*/
	enable_fid_change_on_sb(sysinfo->sbbusn, sysinfo->sbdn);

	post_code(0x39);

	if (!warm_reset_detect(0)) {			// BSP is node 0
		init_fidvid_bsp(bsp_apicid, sysinfo->nodes);
	} else {
		init_fidvid_stage2(bsp_apicid, 0);	// BSP is node 0
	}

	post_code(0x3A);

	/* show final fid and vid */
	msr=rdmsr(0xc0010071);
	printk(BIOS_DEBUG, "End FIDVIDMSR 0xc0010071 0x%08x 0x%08x\n", msr.hi, msr.lo);
#endif

	sr5650_htinit();

	/* Reset for HT, FIDVID, PLL and errata changes to take affect. */
	if (!warm_reset_detect(0)) {
		printk(BIOS_INFO, "...WARM RESET...\n\n\n");
		soft_reset();
		die("After soft_reset_x - shouldn't see this message!!!\n");
	}

	post_code(0x3B);

	/* It's the time to set ctrl in sysinfo now; */
	printk(BIOS_DEBUG, "fill_mem_ctrl()\n");
	fill_mem_ctrl(sysinfo->nodes, sysinfo->ctrl, spd_addr);

	post_code(0x40);


	timestamp_add_now(TS_BEFORE_INITRAM);
	printk(BIOS_DEBUG, "raminit_amdmct()\n");
	raminit_amdmct(sysinfo);
	timestamp_add_now(TS_AFTER_INITRAM);

	cbmem_initialize_empty();
	post_code(0x41);

	amdmct_cbmem_store_info(sysinfo);

/*
	dump_pci_device_range(PCI_DEV(0, 0x18, 0), 0, 0x200);
	dump_pci_device_range(PCI_DEV(0, 0x18, 1), 0, 0x200);
	dump_pci_device_range(PCI_DEV(0, 0x18, 2), 0, 0x200);
	dump_pci_device_range(PCI_DEV(0, 0x18, 3), 0, 0x200);
*/

//	ram_check(0x00200000, 0x00200000 + (640 * 1024));
//	ram_check(0x40200000, 0x40200000 + (640 * 1024));

//	die("After MCT init before CAR disabled.");

	sr5650_before_pci_init();
	sb7xx_51xx_before_pci_init();

	post_code(0x42);
	post_cache_as_ram();	// BSP switch stack to ram, copy then execute LB.
	post_code(0x43);	// Should never see this post code.
}
Exemple #3
0
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx)
{
	u32 val;

	/* Must come first to enable PCI MMCONF. */
	amd_initmmio();

	post_code(0x31);

	/* Halt if there was a built in self test failure */
	post_code(0x33);
	report_bist_failure(bist);

	sb7xx_51xx_enable_wideio(0, 0x1600); /* though UARTs are on the NUVOTON BMC */
	wpcm450_enable_dev(WPCM450_SP1, 0x164E, CONFIG_TTYS0_BASE);
	sb7xx_51xx_disable_wideio(0);
	post_code(0x34);

	post_code(0x35);
	console_init();

	val = cpuid_eax(1);
	printk(BIOS_DEBUG, "BSP Family_Model: %08x\n", val);
	printk(BIOS_DEBUG, "cpu_init_detectedx = %08lx\n", cpu_init_detectedx);

	post_code(0x37);
	agesawrapper_amdinitreset();

	if (!cpu_init_detectedx && boot_cpu()) {
		post_code(0x38);
		/*
		 * SR5650/5670/5690 RD890 chipset, read pci config space hang at POR,
		 * Disable all Pcie Bridges to work around It.
		 */
		sr56x0_rd890_disable_pcie_bridge();
		post_code(0x39);
		nb_Poweron_Init();
		post_code(0x3A);
		sb_Poweron_Init();
	}
	post_code(0x3B);
	agesawrapper_amdinitearly();

	post_code(0x3C);
	nb_Ht_Init();

	post_code(0x3D);
	/* Reset for HT, FIDVID, PLL and ucode patch(errata) changes to take affect. */
	if (!warm_reset_detect(0)) {
		printk(BIOS_INFO, "...WARM RESET...\n\n\n");
		distinguish_cpu_resets(0);
		soft_reset();
		die("After soft_reset_x - shouldn't see this message!!!\n");
	}

	post_code(0x40);
	agesawrapper_amdinitpost();

	post_code(0x41);
	agesawrapper_amdinitenv();
	post_code(0x42);

	post_code(0x50);
	printk(BIOS_DEBUG, "Disabling cache as RAM ");
	disable_cache_as_ram();
	printk(BIOS_DEBUG, "done\n");

	post_code(0x51);
	copy_and_run();

	/* We will not return,  Should never see this message and post code. */
	printk(BIOS_DEBUG, "should not be here -\n");
	post_code(0x54);
}