AirportFTAClass::AirportFTAClass(
const AirportMovingData *moving_data_,
const byte *terminals_,
const byte num_helipads_,
const byte *entry_points_,
Flags flags_,
const AirportFTAbuildup *apFA,
byte delta_z_
) :
moving_data(moving_data_),
terminals(terminals_),
num_helipads(num_helipads_),
flags(flags_),
nofelements(AirportGetNofElements(apFA)),
entry_points(entry_points_),
delta_z(delta_z_)
{
/* Build the state machine itself */
this->layout = AirportBuildAutomata(this->nofelements, apFA);
}
AirportFTAClass::AirportFTAClass(
const AirportMovingData *moving_data_,
const byte *terminals_,
const byte *helipads_,
const byte *entry_points_,
Flags flags_,
const AirportFTAbuildup *apFA,
byte delta_z_
) :
moving_data(moving_data_),
terminals(terminals_),
helipads(helipads_),
flags(flags_),
nofelements(AirportGetNofElements(apFA)),
entry_points(entry_points_),
delta_z(delta_z_)
{
byte nofterminalgroups, nofhelipadgroups;
/* Set up the terminal and helipad count for an airport.
* TODO: If there are more than 10 terminals or 4 helipads, internal variables
* need to be changed, so don't allow that for now */
uint nofterminals = AirportGetTerminalCount(terminals, &nofterminalgroups);
if (nofterminals > MAX_TERMINALS) {
DEBUG(misc, 0, "[Ap] only a maximum of %d terminals are supported (requested %d)", MAX_TERMINALS, nofterminals);
assert(nofterminals <= MAX_TERMINALS);
}
uint nofhelipads = AirportGetTerminalCount(helipads, &nofhelipadgroups);
if (nofhelipads > MAX_HELIPADS) {
DEBUG(misc, 0, "[Ap] only a maximum of %d helipads are supported (requested %d)", MAX_HELIPADS, nofhelipads);
assert(nofhelipads <= MAX_HELIPADS);
}
/* Get the number of elements from the source table. We also double check this
* with the entry point which must be within bounds and use this information
* later on to build and validate the state machine */
for (DiagDirection i = DIAGDIR_BEGIN; i < DIAGDIR_END; i++) {
if (entry_points[i] >= nofelements) {
DEBUG(misc, 0, "[Ap] entry (%d) must be within the airport (maximum %d)", entry_points[i], nofelements);
assert(entry_points[i] < nofelements);
}
}
/* Build the state machine itself */
layout = AirportBuildAutomata(nofelements, apFA);
DEBUG(misc, 6, "[Ap] #count %3d; #term %2d (%dgrp); #helipad %2d (%dgrp); entries %3d, %3d, %3d, %3d",
nofelements, nofterminals, nofterminalgroups, nofhelipads, nofhelipadgroups,
entry_points[DIAGDIR_NE], entry_points[DIAGDIR_SE], entry_points[DIAGDIR_SW], entry_points[DIAGDIR_NW]);
/* Test if everything went allright. This is only a rude static test checking
* the symantic correctness. By no means does passing the test mean that the
* airport is working correctly or will not deadlock for example */
uint ret = AirportTestFTA(nofelements, layout, terminals);
if (ret != MAX_ELEMENTS) DEBUG(misc, 0, "[Ap] problem with element: %d", ret - 1);
assert(ret == MAX_ELEMENTS);
#ifdef DEBUG_AIRPORT
AirportPrintOut(nofelements, layout, DEBUG_AIRPORT);
#endif
}