/* clock startup for Jellybean with Lemondrop attached
Configure PLL1 to max speed (204MHz).
Note: PLL1 clock is used by M4/M0 core, Peripheral, APB1. */
void cpu_clock_init(void)
{
/* use IRC as clock source for APB1 (including I2C0) */
CGU_BASE_APB1_CLK = CGU_BASE_APB1_CLK_CLK_SEL(CGU_SRC_IRC);
/* use IRC as clock source for APB3 */
CGU_BASE_APB3_CLK = CGU_BASE_APB3_CLK_CLK_SEL(CGU_SRC_IRC);
//FIXME a lot of the details here should be in a CGU driver
/* set xtal oscillator to low frequency mode */
CGU_XTAL_OSC_CTRL &= ~CGU_XTAL_OSC_CTRL_HF_MASK;
/* power on the oscillator and wait until stable */
CGU_XTAL_OSC_CTRL &= ~CGU_XTAL_OSC_CTRL_ENABLE_MASK;
/* Wait about 100us after Crystal Power ON */
delay(WAIT_CPU_CLOCK_INIT_DELAY);
/* use XTAL_OSC as clock source for BASE_M4_CLK (CPU) */
CGU_BASE_M4_CLK = (CGU_BASE_M4_CLK_CLK_SEL(CGU_SRC_XTAL) | CGU_BASE_M4_CLK_AUTOBLOCK(1));
/* use XTAL_OSC as clock source for APB1 */
CGU_BASE_APB1_CLK = CGU_BASE_APB1_CLK_AUTOBLOCK(1)
| CGU_BASE_APB1_CLK_CLK_SEL(CGU_SRC_XTAL);
/* use XTAL_OSC as clock source for APB3 */
CGU_BASE_APB3_CLK = CGU_BASE_APB3_CLK_AUTOBLOCK(1)
| CGU_BASE_APB3_CLK_CLK_SEL(CGU_SRC_XTAL);
cpu_clock_pll1_low_speed();
/* use PLL1 as clock source for BASE_M4_CLK (CPU) */
CGU_BASE_M4_CLK = (CGU_BASE_M4_CLK_CLK_SEL(CGU_SRC_PLL1) | CGU_BASE_M4_CLK_AUTOBLOCK(1));
/* use XTAL_OSC as clock source for PLL0USB */
CGU_PLL0USB_CTRL = CGU_PLL0USB_CTRL_PD(1)
| CGU_PLL0USB_CTRL_AUTOBLOCK(1)
| CGU_PLL0USB_CTRL_CLK_SEL(CGU_SRC_XTAL);
while (CGU_PLL0USB_STAT & CGU_PLL0USB_STAT_LOCK_MASK);
/* configure PLL0USB to produce 480 MHz clock from 12 MHz XTAL_OSC */
/* Values from User Manual v1.4 Table 94, for 12MHz oscillator. */
CGU_PLL0USB_MDIV = 0x06167FFA;
CGU_PLL0USB_NP_DIV = 0x00302062;
CGU_PLL0USB_CTRL |= (CGU_PLL0USB_CTRL_PD(1)
| CGU_PLL0USB_CTRL_DIRECTI(1)
| CGU_PLL0USB_CTRL_DIRECTO(1)
| CGU_PLL0USB_CTRL_CLKEN(1));
/* power on PLL0USB and wait until stable */
CGU_PLL0USB_CTRL &= ~CGU_PLL0USB_CTRL_PD_MASK;
while (!(CGU_PLL0USB_STAT & CGU_PLL0USB_STAT_LOCK_MASK));
/* use PLL0USB as clock source for USB0 */
CGU_BASE_USB0_CLK = CGU_BASE_USB0_CLK_AUTOBLOCK(1)
| CGU_BASE_USB0_CLK_CLK_SEL(CGU_SRC_PLL0USB);
/* use PLL0USB as clock source for IDIVA */
/* divide by 4 */
CGU_IDIVA_CTRL = CGU_IDIVA_CTRL_IDIV(3)
| CGU_IDIVA_CTRL_AUTOBLOCK(1)
| CGU_IDIVA_CTRL_CLK_SEL(CGU_SRC_PLL0USB);
/* use IDIVA as clock source for IDIVB */
/* divide by 2 */
CGU_IDIVB_CTRL = CGU_IDIVB_CTRL_IDIV(1)
| CGU_IDIVB_CTRL_AUTOBLOCK(1)
| CGU_IDIVA_CTRL_CLK_SEL(CGU_SRC_IDIVA);
/* Use IDIVB for CLKOUT */
CGU_BASE_OUT_CLK = CGU_BASE_OUT_CLK_AUTOBLOCK(1)
| CGU_BASE_OUT_CLK_CLK_SEL(CGU_SRC_IDIVB);
/* use IDIVB as clock source for USB1 */
CGU_BASE_USB1_CLK = CGU_BASE_USB1_CLK_AUTOBLOCK(1)
| CGU_BASE_USB1_CLK_CLK_SEL(CGU_SRC_IDIVB);
/* Switch peripheral clock over to use PLL1 (204MHz) */
CGU_BASE_PERIPH_CLK = CGU_BASE_PERIPH_CLK_AUTOBLOCK(1)
| CGU_BASE_PERIPH_CLK_CLK_SEL(CGU_SRC_PLL1);
/* Switch APB1 clock over to use PLL1 (204MHz) */
CGU_BASE_APB1_CLK = CGU_BASE_APB1_CLK_AUTOBLOCK(1)
| CGU_BASE_APB1_CLK_CLK_SEL(CGU_SRC_PLL1);
/* Switch APB3 clock over to use PLL1 (204MHz) */
CGU_BASE_APB3_CLK = CGU_BASE_APB3_CLK_AUTOBLOCK(1)
| CGU_BASE_APB3_CLK_CLK_SEL(CGU_SRC_PLL1);
CGU_BASE_SSP0_CLK = CGU_BASE_SSP0_CLK_AUTOBLOCK(1)
| CGU_BASE_SSP0_CLK_CLK_SEL(CGU_SRC_PLL1);
CGU_BASE_SSP1_CLK = CGU_BASE_SSP1_CLK_AUTOBLOCK(1)
| CGU_BASE_SSP1_CLK_CLK_SEL(CGU_SRC_PLL1);
}
/* clock startup for LPC4320 configure PLL1 to max speed (204MHz).
Note: PLL1 clock is used by M4/M0 core, Peripheral, APB1. */
void cpu_clock_init(void)
{
/* use IRC as clock source for APB1 (including I2C0) */
CGU_BASE_APB1_CLK = CGU_BASE_APB1_CLK_CLK_SEL(CGU_SRC_IRC);
/* use IRC as clock source for APB3 */
CGU_BASE_APB3_CLK = CGU_BASE_APB3_CLK_CLK_SEL(CGU_SRC_IRC);
i2c_bus_start(clock_gen.bus, &i2c_config_si5351c_slow_clock);
si5351c_disable_all_outputs(&clock_gen);
si5351c_disable_oeb_pin_control(&clock_gen);
si5351c_power_down_all_clocks(&clock_gen);
si5351c_set_crystal_configuration(&clock_gen);
si5351c_enable_xo_and_ms_fanout(&clock_gen);
si5351c_configure_pll_sources(&clock_gen);
si5351c_configure_pll_multisynth(&clock_gen);
/*
* Clocks:
* CLK0 -> MAX5864/CPLD
* CLK1 -> CPLD
* CLK2 -> SGPIO
* CLK3 -> External Clock Output (power down at boot)
* CLK4 -> RFFC5072 (MAX2837 on rad1o)
* CLK5 -> MAX2837 (MAX2871 on rad1o)
* CLK6 -> none
* CLK7 -> LPC43xx (uses a 12MHz crystal by default)
*/
/* MS4/CLK4 is the source for the RFFC5071 mixer (MAX2837 on rad1o). */
si5351c_configure_multisynth(&clock_gen, 4, 20*128-512, 0, 1, 0); /* 800/20 = 40MHz */
/* MS5/CLK5 is the source for the MAX2837 clock input (MAX2871 on rad1o). */
si5351c_configure_multisynth(&clock_gen, 5, 20*128-512, 0, 1, 0); /* 800/20 = 40MHz */
/* MS6/CLK6 is unused. */
/* MS7/CLK7 is unused. */
/* Set to 10 MHz, the common rate between Jawbreaker and HackRF One. */
sample_rate_set(10000000);
si5351c_set_clock_source(&clock_gen, PLL_SOURCE_XTAL);
// soft reset
// uint8_t resetdata[] = { 177, 0xac };
// si5351c_write(&clock_gen, resetdata, sizeof(resetdata));
si5351c_reset_pll(&clock_gen);
si5351c_enable_clock_outputs(&clock_gen);
//FIXME disable I2C
/* Kick I2C0 down to 400kHz when we switch over to APB1 clock = 204MHz */
i2c_bus_start(clock_gen.bus, &i2c_config_si5351c_fast_clock);
/*
* 12MHz clock is entering LPC XTAL1/OSC input now.
* On HackRF One and Jawbreaker, there is a 12 MHz crystal at the LPC.
* Set up PLL1 to run from XTAL1 input.
*/
//FIXME a lot of the details here should be in a CGU driver
/* set xtal oscillator to low frequency mode */
CGU_XTAL_OSC_CTRL &= ~CGU_XTAL_OSC_CTRL_HF_MASK;
/* power on the oscillator and wait until stable */
CGU_XTAL_OSC_CTRL &= ~CGU_XTAL_OSC_CTRL_ENABLE_MASK;
/* Wait about 100us after Crystal Power ON */
delay(WAIT_CPU_CLOCK_INIT_DELAY);
/* use XTAL_OSC as clock source for BASE_M4_CLK (CPU) */
CGU_BASE_M4_CLK = (CGU_BASE_M4_CLK_CLK_SEL(CGU_SRC_XTAL) | CGU_BASE_M4_CLK_AUTOBLOCK(1));
/* use XTAL_OSC as clock source for APB1 */
CGU_BASE_APB1_CLK = CGU_BASE_APB1_CLK_AUTOBLOCK(1)
| CGU_BASE_APB1_CLK_CLK_SEL(CGU_SRC_XTAL);
/* use XTAL_OSC as clock source for APB3 */
CGU_BASE_APB3_CLK = CGU_BASE_APB3_CLK_AUTOBLOCK(1)
| CGU_BASE_APB3_CLK_CLK_SEL(CGU_SRC_XTAL);
cpu_clock_pll1_low_speed();
/* use PLL1 as clock source for BASE_M4_CLK (CPU) */
CGU_BASE_M4_CLK = (CGU_BASE_M4_CLK_CLK_SEL(CGU_SRC_PLL1) | CGU_BASE_M4_CLK_AUTOBLOCK(1));
/* use XTAL_OSC as clock source for PLL0USB */
CGU_PLL0USB_CTRL = CGU_PLL0USB_CTRL_PD(1)
| CGU_PLL0USB_CTRL_AUTOBLOCK(1)
| CGU_PLL0USB_CTRL_CLK_SEL(CGU_SRC_XTAL);
while (CGU_PLL0USB_STAT & CGU_PLL0USB_STAT_LOCK_MASK);
/* configure PLL0USB to produce 480 MHz clock from 12 MHz XTAL_OSC */
/* Values from User Manual v1.4 Table 94, for 12MHz oscillator. */
CGU_PLL0USB_MDIV = 0x06167FFA;
CGU_PLL0USB_NP_DIV = 0x00302062;
CGU_PLL0USB_CTRL |= (CGU_PLL0USB_CTRL_PD(1)
| CGU_PLL0USB_CTRL_DIRECTI(1)
| CGU_PLL0USB_CTRL_DIRECTO(1)
| CGU_PLL0USB_CTRL_CLKEN(1));
/* power on PLL0USB and wait until stable */
CGU_PLL0USB_CTRL &= ~CGU_PLL0USB_CTRL_PD_MASK;
while (!(CGU_PLL0USB_STAT & CGU_PLL0USB_STAT_LOCK_MASK));
/* use PLL0USB as clock source for USB0 */
CGU_BASE_USB0_CLK = CGU_BASE_USB0_CLK_AUTOBLOCK(1)
| CGU_BASE_USB0_CLK_CLK_SEL(CGU_SRC_PLL0USB);
/* Switch peripheral clock over to use PLL1 (204MHz) */
CGU_BASE_PERIPH_CLK = CGU_BASE_PERIPH_CLK_AUTOBLOCK(1)
| CGU_BASE_PERIPH_CLK_CLK_SEL(CGU_SRC_PLL1);
/* Switch APB1 clock over to use PLL1 (204MHz) */
CGU_BASE_APB1_CLK = CGU_BASE_APB1_CLK_AUTOBLOCK(1)
| CGU_BASE_APB1_CLK_CLK_SEL(CGU_SRC_PLL1);
/* Switch APB3 clock over to use PLL1 (204MHz) */
CGU_BASE_APB3_CLK = CGU_BASE_APB3_CLK_AUTOBLOCK(1)
| CGU_BASE_APB3_CLK_CLK_SEL(CGU_SRC_PLL1);
CGU_BASE_SSP0_CLK = CGU_BASE_SSP0_CLK_AUTOBLOCK(1)
| CGU_BASE_SSP0_CLK_CLK_SEL(CGU_SRC_PLL1);
CGU_BASE_SSP1_CLK = CGU_BASE_SSP1_CLK_AUTOBLOCK(1)
| CGU_BASE_SSP1_CLK_CLK_SEL(CGU_SRC_PLL1);
#if (defined JAWBREAKER || defined HACKRF_ONE)
/* Disable unused clocks */
/* Start with PLLs */
CGU_PLL0AUDIO_CTRL = CGU_PLL0AUDIO_CTRL_PD(1);
/* Dividers */
CGU_IDIVA_CTRL = CGU_IDIVA_CTRL_PD(1);
CGU_IDIVB_CTRL = CGU_IDIVB_CTRL_PD(1);
CGU_IDIVC_CTRL = CGU_IDIVC_CTRL_PD(1);
CGU_IDIVD_CTRL = CGU_IDIVD_CTRL_PD(1);
CGU_IDIVE_CTRL = CGU_IDIVE_CTRL_PD(1);
/* Base clocks */
CGU_BASE_SPIFI_CLK = CGU_BASE_SPIFI_CLK_PD(1); /* SPIFI is only used at boot */
CGU_BASE_USB1_CLK = CGU_BASE_USB1_CLK_PD(1); /* USB1 is not exposed on HackRF */
CGU_BASE_PHY_RX_CLK = CGU_BASE_PHY_RX_CLK_PD(1);
CGU_BASE_PHY_TX_CLK = CGU_BASE_PHY_TX_CLK_PD(1);
CGU_BASE_LCD_CLK = CGU_BASE_LCD_CLK_PD(1);
CGU_BASE_VADC_CLK = CGU_BASE_VADC_CLK_PD(1);
CGU_BASE_SDIO_CLK = CGU_BASE_SDIO_CLK_PD(1);
CGU_BASE_UART0_CLK = CGU_BASE_UART0_CLK_PD(1);
CGU_BASE_UART1_CLK = CGU_BASE_UART1_CLK_PD(1);
CGU_BASE_UART2_CLK = CGU_BASE_UART2_CLK_PD(1);
CGU_BASE_UART3_CLK = CGU_BASE_UART3_CLK_PD(1);
CGU_BASE_OUT_CLK = CGU_BASE_OUT_CLK_PD(1);
CGU_BASE_AUDIO_CLK = CGU_BASE_AUDIO_CLK_PD(1);
CGU_BASE_CGU_OUT0_CLK = CGU_BASE_CGU_OUT0_CLK_PD(1);
CGU_BASE_CGU_OUT1_CLK = CGU_BASE_CGU_OUT1_CLK_PD(1);
/* Disable unused peripheral clocks */
CCU1_CLK_APB1_CAN1_CFG = 0;
CCU1_CLK_APB1_I2S_CFG = 0;
CCU1_CLK_APB1_MOTOCONPWM_CFG = 0;
CCU1_CLK_APB3_ADC0_CFG = 0;
CCU1_CLK_APB3_ADC1_CFG = 0;
CCU1_CLK_APB3_CAN0_CFG = 0;
CCU1_CLK_APB3_DAC_CFG = 0;
CCU1_CLK_M4_DMA_CFG = 0;
CCU1_CLK_M4_EMC_CFG = 0;
CCU1_CLK_M4_EMCDIV_CFG = 0;
CCU1_CLK_M4_ETHERNET_CFG = 0;
CCU1_CLK_M4_LCD_CFG = 0;
CCU1_CLK_M4_QEI_CFG = 0;
CCU1_CLK_M4_RITIMER_CFG = 0;
CCU1_CLK_M4_SCT_CFG = 0;
CCU1_CLK_M4_SDIO_CFG = 0;
CCU1_CLK_M4_SPIFI_CFG = 0;
CCU1_CLK_M4_TIMER0_CFG = 0;
CCU1_CLK_M4_TIMER1_CFG = 0;
CCU1_CLK_M4_TIMER2_CFG = 0;
CCU1_CLK_M4_TIMER3_CFG = 0;
CCU1_CLK_M4_UART1_CFG = 0;
CCU1_CLK_M4_USART0_CFG = 0;
CCU1_CLK_M4_USART2_CFG = 0;
CCU1_CLK_M4_USART3_CFG = 0;
CCU1_CLK_M4_USB1_CFG = 0;
CCU1_CLK_M4_VADC_CFG = 0;
// CCU1_CLK_SPIFI_CFG = 0;
// CCU1_CLK_USB1_CFG = 0;
// CCU1_CLK_VADC_CFG = 0;
// CCU2_CLK_APB0_UART1_CFG = 0;
// CCU2_CLK_APB0_USART0_CFG = 0;
// CCU2_CLK_APB2_USART2_CFG = 0;
// CCU2_CLK_APB2_USART3_CFG = 0;
// CCU2_CLK_APLL_CFG = 0;
// CCU2_CLK_SDIO_CFG = 0;
#endif
#ifdef RAD1O
/* Disable unused clock outputs. They generate noise. */
scu_pinmux(CLK0, SCU_CLK_IN | SCU_CONF_FUNCTION7);
scu_pinmux(CLK2, SCU_CLK_IN | SCU_CONF_FUNCTION7);
#endif
}