/*****************************************************************************
Function:
void WF_SpiInit(void)
Summary:
Initializes the SPI interface to the MRF24WB0M device.
Description:
Configures the SPI interface for communications with the MRF24WB0M.
Precondition:
None
Parameters:
None
Returns:
None
Remarks:
This function is called by WFHardwareInit.
*****************************************************************************/
void WF_SpiInit(void)
{
/* disable the spi interrupt */
#if defined( __PIC32MX__ )
WF_SPI_IE_CLEAR = WF_SPI_INT_BITS;
#else
WF_SPI_IE = 0;
#endif
#if defined( __18CXX)
WF_SPI_IP = 0;
#endif
// Set up the SPI module on the PIC for communications with the MRF24WB0M
WF_CS_IO = 1;
WF_CS_TRIS = 0; // Drive SPI MRF24WB0M chip select pin
#if defined( __18CXX)
WF_SCK_TRIS = 0; /* SPI Clock is an output */
WF_SDO_TRIS = 0; /* SPI Data Out is an output */
WF_SDI_TRIS = 1; /* SPI Data In is an input */
#else
// We'll let the module control the pins.
#endif
#if !defined( SPI_IS_SHARED )
ConfigureSpiMRF24WB0M();
#endif
/* clear the completion flag */
ClearSPIDoneFlag();
}
/*****************************************************************************
Function:
void SPIFlashEraseSector(DWORD dwAddr)
Summary:
Erases a sector.
Description:
This function erases a sector in the Flash part. It is called
internally by the SPIFlashWrite functions whenever a write is attempted
on the first byte in a sector.
Precondition:
SPIFlashInit has been called.
Parameters:
dwAddr - The address of the sector to be erased.
Returns:
None
Remarks:
See Remarks in SPIFlashBeginWrite for important information about Flash
memory parts.
***************************************************************************/
void SPIFlashEraseSector(DWORD dwAddr)
{
volatile BYTE Dummy;
BYTE vSPIONSave;
#if defined(__18CXX)
BYTE SPICON1Save;
#elif defined(__C30__)
WORD SPICON1Save;
#else
DWORD SPICON1Save;
#endif
// Save SPI state (clock speed)
SPICON1Save = SPIFLASH_SPICON1;
vSPIONSave = SPI_ON_BIT;
// Configure SPI
SPI_ON_BIT = 0;
SPIFLASH_SPICON1 = PROPER_SPICON1;
SPI_ON_BIT = 1;
// Enable writing
_SendCmd(WREN);
// Activate the chip select
SPIFLASH_CS_IO = 0;
ClearSPIDoneFlag();
// Issue ERASE command with address
SPIFLASH_SSPBUF = ERASE_4K;
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
SPIFLASH_SSPBUF = ((BYTE*)&dwAddr)[2];
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
SPIFLASH_SSPBUF = ((BYTE*)&dwAddr)[1];
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
SPIFLASH_SSPBUF = ((BYTE*)&dwAddr)[0];
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
// Deactivate chip select to perform the erase
SPIFLASH_CS_IO = 1;
// Wait for erase to complete
_WaitWhileBusy();
// Restore SPI state
SPI_ON_BIT = 0;
SPIFLASH_SPICON1 = SPICON1Save;
SPI_ON_BIT = vSPIONSave;
}
void SPIRAMPutROMArray(WORD wAddress, ROM BYTE *vData, WORD wLength)
{
volatile BYTE Dummy;
BYTE vSPIONSave;
BYTE SPICON1Save;
// Ignore operations when the source data is NULL
if(vData == NULL)
return;
if(wLength == 0u)
return;
// Save SPI state (clock speed)
SPICON1Save = SPIRAM_SPICON1;
vSPIONSave = SPI_ON_BIT;
// Configure SPI
SPI_ON_BIT = 0;
SPIRAM_SPICON1 = PROPER_SPICON1;
SPI_ON_BIT = 1;
// Activate chip select
SPIRAM_CS_IO = 0;
ClearSPIDoneFlag();
// Send WRITE opcode
SPIRAM_SSPBUF = WRITE;
WaitForDataByte();
Dummy = SPIRAM_SSPBUF;
// Send address
SPIRAM_SSPBUF = ((BYTE*)&wAddress)[1];
WaitForDataByte();
Dummy = SPIRAM_SSPBUF;
SPIRAM_SSPBUF = ((BYTE*)&wAddress)[0];
WaitForDataByte();
Dummy = SPIRAM_SSPBUF;
// Write data
while(wLength--)
{
SPIRAM_SSPBUF = *vData++;
WaitForDataByte();
Dummy = SPIRAM_SSPBUF;
};
// Deactivate chip select
SPIRAM_CS_IO = 1;
// Restore SPI state
SPI_ON_BIT = 0;
SPIRAM_SPICON1 = SPICON1Save;
SPI_ON_BIT = vSPIONSave;
}
/*****************************************************************************
Function:
static void _SendCmd(BYTE cmd)
Summary:
Sends a single-byte command to the SPI Flash part.
Description:
This function sends a single-byte command to the SPI Flash part. It is
used for commands such as WREN, WRDI, and EWSR that must have the chip
select activated, then deactivated immediately after the command is
transmitted.
Precondition:
SPIFlashInit has been called.
Parameters:
cmd - The single-byte command code to send
Returns:
None
***************************************************************************/
static void _SendCmd(BYTE cmd)
{
// Activate chip select
SPIFLASH_CS_IO = 0;
ClearSPIDoneFlag();
// Send instruction
SPIFLASH_SSPBUF = cmd;
WaitForDataByte();
cmd = SPIFLASH_SSPBUF;
// Deactivate chip select
SPIFLASH_CS_IO = 1;
}
/*********************************************************************
* Function: BOOL XEEIsBusy(void)
*
* PreCondition: XEEInit() is already called.
*
* Input: None
*
* Output: FALSE if EEPROM is not busy
* TRUE if EEPROM is busy
*
* Side Effects: None
*
* Overview: Reads the status register
*
* Note: None
********************************************************************/
BOOL XEEIsBusy(void)
{
volatile BYTE_VAL result;
BYTE vSPIONSave;
#if defined(__18CXX)
BYTE SPICON1Save;
#elif defined(__C30__)
WORD SPICON1Save;
#else
DWORD SPICON1Save;
#endif
// Save SPI state
SPICON1Save = EEPROM_SPICON1;
vSPIONSave = SPI_ON_BIT;
// Configure SPI
SPI_ON_BIT = 0;
EEPROM_SPICON1 = PROPER_SPICON1;
SPI_ON_BIT = 1;
ASSERT_EEPROM_CS_IO
// Send RDSR - Read Status Register opcode
EEPROM_SSPBUF = OPCODE_RDSR;
WaitForDataByte();
result.Val = EEPROM_SSPBUF;
// Get register contents
EEPROM_SSPBUF = 0;
WaitForDataByte();
result.Val = EEPROM_SSPBUF;
DEASSERT_EEPROM_CS_IO
// Restore SPI State
SPI_ON_BIT = 0;
EEPROM_SPICON1 = SPICON1Save;
SPI_ON_BIT = vSPIONSave;
ClearSPIDoneFlag();
return result.bits.b0;
}
void XEEInit(void)
{
EEPROM_CS_IO = 1;
EEPROM_CS_TRIS = 0; // Drive SPI EEPROM chip select pin
EEPROM_SCK_TRIS = 0; // Set SCK pin as an output
EEPROM_SDI_TRIS = 1; // Make sure SDI pin is an input
EEPROM_SDO_TRIS = 0; // Set SDO pin as an output
ClearSPIDoneFlag();
#if defined(__C30__)
EEPROM_SPICON1 = PROPER_SPICON1; // See PROPER_SPICON1 definition above
EEPROM_SPICON2 = 0;
EEPROM_SPISTAT = 0; // clear SPI
EEPROM_SPISTATbits.SPIEN = 1;
#elif defined(__C32__)
EEPROM_SPIBRG = (SYS_CLK_PeripheralClockGet()-1ul)/2ul/EEPROM_MAX_SPI_FREQ;
EEPROM_SPICON1 = PROPER_SPICON1;
#endif
}
/*****************************************************************************
Function:
void WF_SpiEnableChipSelect(void)
Summary:
Enables the MRF24WB0M SPI chip select.
Description:
Enables the MRF24WB0M SPI chip select as part of the sequence of SPI
communications.
Precondition:
None
Parameters:
None
Returns:
None
Remarks:
If the SPI bus is shared with other peripherals then the current SPI context
is saved.
*****************************************************************************/
void WF_SpiEnableChipSelect(void)
{
#if defined(__18CXX)
static volatile UINT8 dummy;
#endif
#if defined(SPI_IS_SHARED)
SaveSpiContext();
ConfigureSpiMRF24WB0M();
#endif
/* set Slave Select low (enable SPI chip select on MRF24WB0M) */
WF_CS_IO = 0;
/* clear any pending interrupts */
#if defined(__18CXX)
dummy = WF_SSPBUF;
ClearSPIDoneFlag();
#endif
}
void XEEInit(void)
{
EEPROM_CS_IO = 1;
EEPROM_CS_TRIS = 0; // Drive SPI EEPROM chip select pin
EEPROM_SCK_TRIS = 0; // Set SCK pin as an output
EEPROM_SDI_TRIS = 1; // Make sure SDI pin is an input
EEPROM_SDO_TRIS = 0; // Set SDO pin as an output
ClearSPIDoneFlag();
#if defined(__C30__)
EEPROM_SPICON1 = PROPER_SPICON1; // See PROPER_SPICON1 definition above
EEPROM_SPICON2 = 0;
EEPROM_SPISTAT = 0; // clear SPI
EEPROM_SPISTATbits.SPIEN = 1;
#elif defined(__C32__)
EEPROM_SPIBRG = (GetPeripheralClock()-1ul)/2ul/EEPROM_MAX_SPI_FREQ;
EEPROM_SPICON1 = PROPER_SPICON1;
#elif defined(__18CXX)
EEPROM_SPICON1 = PROPER_SPICON1; // See PROPER_SPICON1 definition above
EEPROM_SPISTATbits.CKE = 1; // Transmit data on rising edge of clock
EEPROM_SPISTATbits.SMP = 0; // Input sampled at middle of data output time
#endif
}
/*****************************************************************************
Function:
static void _WaitWhileBusy(void)
Summary:
Waits for the SPI Flash part to indicate it is idle.
Description:
This function waits for the SPI Flash part to indicate it is idle. It is
used in the programming functions to wait for operations to complete.
Precondition:
SPIFlashInit has been called.
Parameters:
None
Returns:
None
***************************************************************************/
static void _WaitWhileBusy(void)
{
volatile BYTE Dummy;
// Activate chip select
SPIFLASH_CS_IO = 0;
ClearSPIDoneFlag();
// Send Read Status Register instruction
SPIFLASH_SSPBUF = RDSR;
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
// Poll the BUSY bit
do
{
SPIFLASH_SSPBUF = 0x00;
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
} while(Dummy & BUSY);
// Deactivate chip select
SPIFLASH_CS_IO = 1;
}
/*********************************************************************
* Function: XEE_RESULT XEEReadArray(DWORD address,
* BYTE *buffer,
* WORD length)
*
* PreCondition: XEEInit() is already called.
*
* Input: address - Address from where array is to be read
* buffer - Caller supplied buffer to hold the data
* length - Number of bytes to read.
*
* Output: XEE_SUCCESS
*
* Side Effects: None
*
* Overview: Reads desired number of bytes in sequential mode.
* This function performs all necessary steps
* and releases the bus when finished.
*
* Note: None
********************************************************************/
XEE_RESULT XEEReadArray(DWORD address,
BYTE *buffer,
WORD length)
{
volatile BYTE Dummy;
BYTE vSPIONSave;
#if defined(__18CXX)
BYTE SPICON1Save;
#elif defined(__C30__)
WORD SPICON1Save;
#else
DWORD SPICON1Save;
#endif
// Save SPI state (clock speed)
SPICON1Save = EEPROM_SPICON1;
vSPIONSave = SPI_ON_BIT;
// Configure SPI
SPI_ON_BIT = 0;
EEPROM_SPICON1 = PROPER_SPICON1;
SPI_ON_BIT = 1;
ASSERT_EEPROM_CS_IO
// Send READ opcode
EEPROM_SSPBUF = OPCODE_READ;
WaitForDataByte();
Dummy = EEPROM_SSPBUF;
// Send address
#if defined(USE_EEPROM_25LC1024)
EEPROM_SSPBUF = ((DWORD_VAL*)&address)->v[2];
WaitForDataByte();
Dummy = EEPROM_SSPBUF;
#endif
EEPROM_SSPBUF = ((DWORD_VAL*)&address)->v[1];
WaitForDataByte();
Dummy = EEPROM_SSPBUF;
EEPROM_SSPBUF = ((DWORD_VAL*)&address)->v[0];
WaitForDataByte();
Dummy = EEPROM_SSPBUF;
while(length--)
{
EEPROM_SSPBUF = 0;
WaitForDataByte();
Dummy = EEPROM_SSPBUF;
if(buffer != NULL)
*buffer++ = Dummy;
};
DEASSERT_EEPROM_CS_IO
// Restore SPI state
SPI_ON_BIT = 0;
EEPROM_SPICON1 = SPICON1Save;
SPI_ON_BIT = vSPIONSave;
ClearSPIDoneFlag();
return XEE_SUCCESS;
}
static void DoWrite(void)
{
BYTE i;
volatile BYTE vDummy;
BYTE vSPIONSave;
#if defined(__18CXX)
BYTE SPICON1Save;
#elif defined(__C30__)
WORD SPICON1Save;
#else
DWORD SPICON1Save;
#endif
// Save SPI state
SPICON1Save = EEPROM_SPICON1;
vSPIONSave = SPI_ON_BIT;
// Configure SPI
SPI_ON_BIT = 0;
EEPROM_SPICON1 = PROPER_SPICON1;
SPI_ON_BIT = 1;
// Set the Write Enable latch
ASSERT_EEPROM_CS_IO
EEPROM_SSPBUF = OPCODE_WREN;
WaitForDataByte();
vDummy = EEPROM_SSPBUF;
DEASSERT_EEPROM_CS_IO
// Send WRITE opcode
ASSERT_EEPROM_CS_IO
EEPROM_SSPBUF = OPCODE_WRITE;
WaitForDataByte();
vDummy = EEPROM_SSPBUF;
// Send address
#if defined(USE_EEPROM_25LC1024)
EEPROM_SSPBUF = ((DWORD_VAL*)&EEPROMAddress)->v[2];
WaitForDataByte();
vDummy = EEPROM_SSPBUF;
#endif
EEPROM_SSPBUF = ((DWORD_VAL*)&EEPROMAddress)->v[1];
WaitForDataByte();
vDummy = EEPROM_SSPBUF;
EEPROM_SSPBUF = ((DWORD_VAL*)&EEPROMAddress)->v[0];
WaitForDataByte();
vDummy = EEPROM_SSPBUF;
for(i = 0; i < vBytesInBuffer; i++)
{
// Send the byte to write
EEPROM_SSPBUF = EEPROMBuffer[i];
WaitForDataByte();
vDummy = EEPROM_SSPBUF;
}
// Begin the write
DEASSERT_EEPROM_CS_IO
// Update write address and clear write cache
EEPROMAddress += vBytesInBuffer;
vBytesInBuffer = 0;
// Restore SPI State
SPI_ON_BIT = 0;
EEPROM_SPICON1 = SPICON1Save;
SPI_ON_BIT = vSPIONSave;
// Wait for write to complete
while( XEEIsBusy() );
ClearSPIDoneFlag();
}
/*********************************************************************
* Function: void SPIRAMGetArray(WORD wAddress, BYTE *vData, WORD wLength)
*
* PreCondition:
*
* Input:
*
* Output:
*
* Side Effects: None
*
* Overview:
*
* Note: None
********************************************************************/
void SPIRAMGetArray(WORD wAddress, BYTE *vData, WORD wLength)
{
volatile BYTE Dummy;
BYTE vSPIONSave;
#if defined(__18CXX)
BYTE SPICON1Save;
#elif defined(__C30__)
WORD SPICON1Save;
#else
DWORD SPICON1Save;
#endif
// Ignore operations when the destination is NULL or nothing to read
if(vData == NULL)
return;
if(wLength == 0u)
return;
// Save SPI state (clock speed)
SPICON1Save = SPIRAM_SPICON1;
vSPIONSave = SPI_ON_BIT;
// Configure SPI
SPI_ON_BIT = 0;
SPIRAM_SPICON1 = PROPER_SPICON1;
SPI_ON_BIT = 1;
// Activate chip select
SPIRAM_CS_IO = 0;
ClearSPIDoneFlag();
// Send READ opcode
SPIRAM_SSPBUF = READ;
WaitForDataByte();
Dummy = SPIRAM_SSPBUF;
// Send address
SPIRAM_SSPBUF = ((BYTE*)&wAddress)[1];
WaitForDataByte();
Dummy = SPIRAM_SSPBUF;
SPIRAM_SSPBUF = ((BYTE*)&wAddress)[0];
WaitForDataByte();
Dummy = SPIRAM_SSPBUF;
// Read data
while(wLength--)
{
SPIRAM_SSPBUF = 0;
WaitForDataByte();
*vData++ = SPIRAM_SSPBUF;
};
// Deactivate chip select
SPIRAM_CS_IO = 1;
// Restore SPI state
SPI_ON_BIT = 0;
SPIRAM_SPICON1 = SPICON1Save;
SPI_ON_BIT = vSPIONSave;
}
/*********************************************************************
* Function: void SPIRAMInit(void)
*
* PreCondition: None
*
* Input: None
*
* Output: None
*
* Side Effects: None
*
* Overview: Initialize SPI module to communicate to serial
* RAM.
*
* Note: Code sets SPI clock to Fosc/4.
********************************************************************/
void SPIRAMInit(void)
{
volatile BYTE Dummy;
BYTE vSPIONSave;
#if defined(__18CXX)
BYTE SPICON1Save;
#elif defined(__C30__)
WORD SPICON1Save;
#else
DWORD SPICON1Save;
#endif
SPIRAM_CS_IO = 1;
SPIRAM_CS_TRIS = 0; // Drive SPI RAM chip select pin
SPIRAM_SCK_TRIS = 0; // Set SCK pin as an output
SPIRAM_SDI_TRIS = 1; // Make sure SDI pin is an input
SPIRAM_SDO_TRIS = 0; // Set SDO pin as an output
// Save SPI state (clock speed)
SPICON1Save = SPIRAM_SPICON1;
vSPIONSave = SPI_ON_BIT;
// Configure SPI
SPI_ON_BIT = 0;
SPIRAM_SPICON1 = PROPER_SPICON1;
SPI_ON_BIT = 1;
ClearSPIDoneFlag();
#if defined(__C30__)
SPIRAM_SPICON2 = 0;
SPIRAM_SPISTAT = 0; // clear SPI
SPIRAM_SPISTATbits.SPIEN = 1;
#elif defined(__C32__)
SPIRAM_SPIBRG = (GetPeripheralClock()-1ul)/2ul/SPIRAM_MAX_SPI_FREQ;
SPIRAM_SPICON1bits.CKE = 1;
SPIRAM_SPICON1bits.MSTEN = 1;
SPIRAM_SPICON1bits.ON = 1;
#elif defined(__18CXX)
SPIRAM_SPISTATbits.CKE = 1; // Transmit data on rising edge of clock
SPIRAM_SPISTATbits.SMP = 0; // Input sampled at middle of data output time
#endif
// Set Burst mode
// Activate chip select
SPIRAM_CS_IO = 0;
// Send Write Status Register opcode
SPIRAM_SSPBUF = WRSR;
WaitForDataByte();
Dummy = SPIRAM_SSPBUF;
// Set status register to 0b01000000 to enable burst mode
SPIRAM_SSPBUF = 0x40;
WaitForDataByte();
Dummy = SPIRAM_SSPBUF;
// Deactivate chip select
SPIRAM_CS_IO = 1;
// Restore SPI state
SPI_ON_BIT = 0;
SPIRAM_SPICON1 = SPICON1Save;
SPI_ON_BIT = vSPIONSave;
}
/*****************************************************************************
* FUNCTION: zgHALSpiInit
*
* RETURNS: None
*
* PARAMS: None
*
* NOTES: Called by ZGPrvComInit() during init to configure the SPI I/O.
*****************************************************************************/
tZGVoidReturn zgHALSpiInit(tZGVoidInput)
{
/* disable the spi interrupt */
#if defined( __PIC32MX__ )
ZG_SPI_IE_CLEAR = ZG_SPI_INT_BITS;
#else
ZG_SPI_IE = 0;
#endif
#if defined( __18CXX)
ZG_SPI_IP = 0;
#endif
// Set up the SPI module on the PIC for communications with the ZG2100
/* enable the SPI pins */
// #if defined(EEPROM_CS_TRIS)
// EEPROM_CS_IO = 1; // deselect EEPROM
// EEPROM_CS_TRIS = 0; // Drive SPI EEPROM chip select pin
// #endif
ZG_CS_IO = 1;
ZG_CS_TRIS = 0; // Drive SPI ZG2100 chip select pin
#if defined( __18CXX)
ZG_SCK_TRIS = 0;
ZG_SDO_TRIS = 0;
ZG_SDI_TRIS = 1;
#else
// We'll let the module control the pins.
#endif
/* clear the completion flag */
ClearSPIDoneFlag();
#ifdef DEDICATED_SPI_ZG
// Configure the SPI here, instead of every time we access it.
/*---------------------------------------------*/
/* Configure SPI I/O for ZG2100 communications */
/*---------------------------------------------*/
/* enable the SPI clocks */
/* set as master */
/* clock idles high */
/* ms bit first */
/* 8 bit tranfer length */
/* data changes on falling edge */
/* data is sampled on rising edge */
/* set the clock divider */
// Set up SPI
#if defined(__18CXX)
ZG_SPICON1 = 0x30; // SSPEN bit is set, SPI in master mode, (0x30 is for FOSC/4),
// IDLE state is high level (0x32 is for FOSC/64)
ZG_SPISTATbits.CKE = 0; // Transmit data on falling edge of clock
ZG_SPISTATbits.SMP = 1; // Input sampled at end? of data output time
#elif defined(__C30__)
ZG_SPICON1 = 0x027B; // Fcy Primary prescaler 1:1, secondary prescaler 2:1, CPK=1, CKE=0, SMP=1
ZG_SPICON2 = 0x0000;
ZG_SPISTAT = 0x8000; // Enable the module
#elif defined( __PIC32MX__ )
ZG_SPI_BRG = (GetPeripheralClock()-1ul)/2ul/ZG_MAX_SPI_FREQ;
ZG_SPICON1 = 0x00000260; // sample at end, data change idle to active, clock idle high, master
ZG_SPICON1bits.ON = 1;
#else
#error Configure SPI for the selected processor
#endif
#endif
SPICXT.suppressDoneHandlerCall = FALSE;
}
/*****************************************************************************
Function:
void SPIFlashWriteArray(BYTE* vData, WORD wLen)
Summary:
Writes an array of bytes to the SPI Flash part.
Description:
This function writes an array of bytes to the SPI Flash part. When the
address pointer crosses a sector boundary (and has more data to write),
the next sector will automatically be erased. If the current address
pointer indicates an address that is not a sector boundary and is not
already erased, the chip will silently ignore the write command until the
next sector boundary is crossed.
Precondition:
SPIFlashInit and SPIFlashBeginWrite have been called, and the current
address is either the front of a sector or has already been erased.
Parameters:
vData - The array to write to the next memory location
wLen - The length of the data to be written
Returns:
None
Remarks:
See Remarks in SPIFlashBeginWrite for important information about Flash
memory parts.
***************************************************************************/
void SPIFlashWriteArray(BYTE* vData, WORD wLen)
{
volatile BYTE Dummy;
BYTE vSPIONSave;
#if defined(__18CXX)
BYTE SPICON1Save;
#elif defined(__C30__)
WORD SPICON1Save;
#else
DWORD SPICON1Save;
#endif
BOOL isStarted;
BYTE vOpcode;
BYTE i;
// Do nothing if no data to process
if(wLen == 0u)
return;
// Save SPI state (clock speed)
SPICON1Save = SPIFLASH_SPICON1;
vSPIONSave = SPI_ON_BIT;
// Configure SPI
SPI_ON_BIT = 0;
SPIFLASH_SPICON1 = PROPER_SPICON1;
SPI_ON_BIT = 1;
// If starting at an odd address, write a single byte
if((dwWriteAddr & 0x01) && wLen)
{
SPIFlashWrite(*vData);
vData++;
wLen--;
}
// Assume we are using AAI Word program mode unless changed later
vOpcode = WRITE_WORD_STREAM;
isStarted = FALSE;
// Loop over all remaining WORDs
while(wLen > 1)
{
// Don't do anything until chip is ready
_WaitWhileBusy();
// If address is a sector boundary
if((dwWriteAddr & SPI_FLASH_SECTOR_MASK) == 0)
SPIFlashEraseSector(dwWriteAddr);
// If not yet started, initiate AAI mode
if(!isStarted)
{
// Enable writing
_SendCmd(WREN);
// Select appropriate programming opcode. The WRITE_WORD_STREAM
// mode is the default if neither of these flags are set.
if(deviceCaps.bits.bWriteByteStream)
vOpcode = WRITE_BYTE_STREAM;
else if(deviceCaps.bits.bPageProgram)
{
// Note: Writing one byte at a time is extremely slow (ex: ~667
// bytes/second write speed on SST SST25VF064C). You can
// improve this by over a couple of orders of magnitude by
// writing a function to write full pages of up to 256 bytes at
// a time. This is implemented this way only because I don't
// have an SST25VF064C handy to test with right now. -HS
while(wLen--)
SPIFlashWrite(*vData++);
return;
}
// Activate the chip select
SPIFLASH_CS_IO = 0;
ClearSPIDoneFlag();
// Issue WRITE_xxx_STREAM command with address
SPIFLASH_SSPBUF = vOpcode;
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
SPIFLASH_SSPBUF = ((BYTE*)&dwWriteAddr)[2];
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
SPIFLASH_SSPBUF = ((BYTE*)&dwWriteAddr)[1];
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
SPIFLASH_SSPBUF = ((BYTE*)&dwWriteAddr)[0];
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
isStarted = TRUE;
}
// Otherwise, just write the AAI command again
else
{
// Assert the chip select pin
SPIFLASH_CS_IO = 0;
ClearSPIDoneFlag();
// Issue the WRITE_STREAM command for continuation
SPIFLASH_SSPBUF = vOpcode;
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
}
// Write a byte or two
for(i = 0; i <= deviceCaps.bits.bWriteWordStream; i++)
{
SPIFLASH_SSPBUF = *vData++;
dwWriteAddr++;
wLen--;
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
}
// Release the chip select to begin the write
SPIFLASH_CS_IO = 1;
// If a boundary was reached, end the write
if((dwWriteAddr & SPI_FLASH_SECTOR_MASK) == 0)
{
_WaitWhileBusy();
_SendCmd(WRDI);
isStarted = FALSE;
}
}
// Wait for write to complete, then exit AAI mode
_WaitWhileBusy();
_SendCmd(WRDI);
// If a byte remains, write the odd address
if(wLen)
SPIFlashWrite(*vData);
// Restore SPI state
SPI_ON_BIT = 0;
SPIFLASH_SPICON1 = SPICON1Save;
SPI_ON_BIT = vSPIONSave;
}
/*****************************************************************************
Function:
void SPIFlashWrite(BYTE vData)
Summary:
Writes a byte to the SPI Flash part.
Description:
This function writes a byte to the SPI Flash part. If the current
address pointer indicates the beginning of a 4kB sector, the entire
sector will first be erased to allow writes to proceed. If the current
address pointer indicates elsewhere, it will be assumed that the sector
has already been erased. If this is not true, the chip will silently
ignore the write command.
Precondition:
SPIFlashInit and SPIFlashBeginWrite have been called, and the current
address is either the front of a 4kB sector or has already been erased.
Parameters:
vData - The byte to write to the next memory location.
Returns:
None
Remarks:
See Remarks in SPIFlashBeginWrite for important information about Flash
memory parts.
***************************************************************************/
void SPIFlashWrite(BYTE vData)
{
volatile BYTE Dummy;
BYTE vSPIONSave;
#if defined(__18CXX)
BYTE SPICON1Save;
#elif defined(__C30__)
WORD SPICON1Save;
#else
DWORD SPICON1Save;
#endif
// Save SPI state (clock speed)
SPICON1Save = SPIFLASH_SPICON1;
vSPIONSave = SPI_ON_BIT;
// Configure SPI
SPI_ON_BIT = 0;
SPIFLASH_SPICON1 = PROPER_SPICON1;
SPI_ON_BIT = 1;
// If address is a boundary, erase a sector first
if((dwWriteAddr & SPI_FLASH_SECTOR_MASK) == 0u)
SPIFlashEraseSector(dwWriteAddr);
// Enable writing
_SendCmd(WREN);
// Activate the chip select
SPIFLASH_CS_IO = 0;
ClearSPIDoneFlag();
// Issue WRITE command with address
SPIFLASH_SSPBUF = WRITE;
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
SPIFLASH_SSPBUF = ((BYTE*)&dwWriteAddr)[2];
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
SPIFLASH_SSPBUF = ((BYTE*)&dwWriteAddr)[1];
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
SPIFLASH_SSPBUF = ((BYTE*)&dwWriteAddr)[0];
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
// Write the byte
SPIFLASH_SSPBUF = vData;
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
dwWriteAddr++;
// Deactivate chip select and wait for write to complete
SPIFLASH_CS_IO = 1;
_WaitWhileBusy();
// Restore SPI state
SPI_ON_BIT = 0;
SPIFLASH_SPICON1 = SPICON1Save;
SPI_ON_BIT = vSPIONSave;
}
/*****************************************************************************
Function:
void SPIFlashInit(void)
Description:
Initializes SPI Flash module.
Precondition:
None
Parameters:
None
Returns:
None
Remarks:
This function is only called once during the lifetime of the application.
Internal:
This function sends WRDI to clear any pending write operation, and also
clears the software write-protect on all memory locations.
***************************************************************************/
void SPIFlashInit(void)
{
BYTE i;
volatile BYTE Dummy;
BYTE vSPIONSave;
#if defined(__18CXX)
BYTE SPICON1Save;
#elif defined(__C30__)
WORD SPICON1Save;
#else
DWORD SPICON1Save;
#endif
SPIFLASH_CS_IO = 1;
SPIFLASH_CS_TRIS = 0; // Drive SPI Flash chip select pin
SPIFLASH_SCK_TRIS = 0; // Set SCK pin as an output
SPIFLASH_SDI_TRIS = 1; // Make sure SDI pin is an input
SPIFLASH_SDO_TRIS = 0; // Set SDO pin as an output
// Save SPI state (clock speed)
SPICON1Save = SPIFLASH_SPICON1;
vSPIONSave = SPI_ON_BIT;
// Configure SPI
SPI_ON_BIT = 0;
SPIFLASH_SPICON1 = PROPER_SPICON1;
SPI_ON_BIT = 1;
ClearSPIDoneFlag();
#if defined(__C30__)
SPIFLASH_SPICON2 = 0;
SPIFLASH_SPISTAT = 0; // clear SPI
SPIFLASH_SPISTATbits.SPIEN = 1;
#elif defined(__C32__)
SPIFLASH_SPIBRG = (GetPeripheralClock()-1ul)/2ul/SPIFLASH_MAX_SPI_FREQ;
#elif defined(__18CXX)
SPIFLASH_SPISTATbits.CKE = 1; // Transmit data on rising edge of clock
SPIFLASH_SPISTATbits.SMP = 0; // Input sampled at middle of data output time
#endif
// Read Device ID code to determine supported device capabilities/instructions
{
// Activate chip select
SPIFLASH_CS_IO = 0;
ClearSPIDoneFlag();
// Send instruction
SPIFLASH_SSPBUF = RDID;
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
// Send 3 byte address (0x000000), discard Manufacture ID, get Device ID
for(i = 0; i < 5; i++)
{
SPIFLASH_SSPBUF = 0x00;
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
}
// Deactivate chip select
SPIFLASH_CS_IO = 1;
// Decode Device Capabilities Flags from Device ID
deviceCaps.v = 0x00;
switch(Dummy)
{
case 0x43: // SST25LF020(A) (2 Mbit) 0xAF, 14us, AAI Byte
case 0x48: // SST25VF512(A) (512 Kbit) 0xAF, 14us, AAI Byte
case 0x49: // SST25VF010A (1 Mbit) 0xAF, 14us, AAI Byte
deviceCaps.bits.bWriteByteStream = 1;
break;
case 0x4B: // SST25VF064C (64 Mbit) 0x02, 1.5ms/256 byte page, no AAI
deviceCaps.bits.bPageProgram = 1;
break;
//case 0x01: // SST25WF512 (512 Kbit) 0xAD, 50us, AAI Word
//case 0x02: // SST25WF010 (1 Mbit) 0xAD, 50us, AAI Word
//case 0x03: // SST25WF020 (2 Mbit) 0xAD, 50us, AAI Word
//case 0x04: // SST25WF040 (4 Mbit) 0xAD, 50us, AAI Word
//case 0x05: // SST25WF080 (8 Mbit) 0xAD, 14us, AAI Word
//case 0x41: // SST25VF016B (16 Mbit) 0xAD, 7us, AAI Word
//case 0x4A: // SST25VF032B (32 Mbit) 0xAD, 7us, AAI Word
//case 0x8C: // SST25VF020B (2 Mbit) 0xAD, 7us, AAI Word
//case 0x8D: // SST25VF040B (4 Mbit) 0xAD, 7us, AAI Word
//case 0x8E: // SST25VF080B (8 Mbit) 0xAD, 7us, AAI Word
// Assume AAI Word programming is supported for the above commented
// devices and unknown devices.
default:
deviceCaps.bits.bWriteWordStream = 1;
}
}
// Clear any pre-existing AAI write mode
// This may occur if the PIC is reset during a write, but the Flash is
// not tied to the same hardware reset.
_SendCmd(WRDI);
// Execute Enable-Write-Status-Register (EWSR) instruction
_SendCmd(EWSR);
// Clear Write-Protect on all memory locations
SPIFLASH_CS_IO = 0;
SPIFLASH_SSPBUF = WRSR;
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
SPIFLASH_SSPBUF = 0x00; // Clear all block protect bits
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
SPIFLASH_CS_IO = 1;
// Restore SPI state
SPI_ON_BIT = 0;
SPIFLASH_SPICON1 = SPICON1Save;
SPI_ON_BIT = vSPIONSave;
}
/*****************************************************************************
* FUNCTION: zgHALSpiTxRx
*
* RETURNS: True is successful, else False
*
* PARAMS: None
*
* NOTES: SPI Tx/Rx mechansim between Host CPU and ZG2100.
*****************************************************************************/
tZGBool zgHALSpiTxRx(tZGVoidInput)
{
#if defined(__18CXX)
volatile tZGU8 dummy;
#endif
tZGU16 numRxPreambleBytes, numTxPreambleBytes;
tZGU16 numRxDataBytes, numTxDataBytes;
tZGU16 totalNumBytes;
tZGU8 *p_txPreBuf, *p_rxPreBuf;
tZGU8 *p_txDataBuf, *p_rxDataBuf;
tZGU8 ROM *p_txDataRomBuf;
tZGU8 romFlag;
tZGU8 rxTrash;
numRxPreambleBytes = SPICXT.rxPreambleLength;
numTxPreambleBytes = SPICXT.txPreambleLength;
numRxDataBytes = SPICXT.rxBufferLength + SPICXT.excessRxLength;
numTxDataBytes = SPICXT.txLength;
p_rxPreBuf = SPICXT.pRxPreambleBuffer;
p_txPreBuf = SPICXT.pTxPreambleBuffer;
p_txDataBuf = SPICXT.pTxBuffer;
p_txDataRomBuf = SPICXT.pTxRomBuffer;
p_rxDataBuf = SPICXT.pRxBuffer;
// if more tx bytes than rx bytes, or the same count for both
if ( (numTxPreambleBytes + numTxDataBytes) >= (numRxPreambleBytes + numRxDataBytes) )
{
totalNumBytes = numTxPreambleBytes + numTxDataBytes;
}
// else more rx bytes than tx bytes
else
{
totalNumBytes = numRxPreambleBytes + numRxDataBytes;
}
// if any tx data
if (numTxDataBytes > 0u)
{
// if using tx RAM buffer
if (SPICXT.pTxBuffer != 0u)
{
romFlag = kZGBoolFalse;
}
else if (SPICXT.pTxRomBuffer != 0u)
{
romFlag = kZGBoolTrue;
}
else
{
ZGSYS_DRIVER_ASSERT(5, (ROM char *)"SpiTxRx: Invalid Tx pointer.\n");
}
}
spiSuppressDoneHandlerCall = SPICXT.suppressDoneHandlerCall;
SPICXT.suppressDoneHandlerCall = FALSE; // set back to default state of false, only raw txrx will set true
#ifndef DEDICATED_SPI_ZG
// Save SPI context so we can restore it to function entry state at end of this function
SaveSpiContext();
/*---------------------------------------------*/
/* Configure SPI I/O for ZG2100 communications */
/*---------------------------------------------*/
/* enable the SPI clocks */
/* set as master */
/* clock idles high */
/* ms bit first */
/* 8 bit tranfer length */
/* data changes on falling edge */
/* data is sampled on rising edge */
/* set the clock divider */
// Set up SPI
#if defined(__18CXX)
ZG_SPICON1 = 0x30; // SSPEN bit is set, SPI in master mode, (0x30 is for FOSC/4),
// IDLE state is high level (0x32 is for FOSC/64)
ZG_SPISTATbits.CKE = 0; // Transmit data on falling edge of clock
ZG_SPISTATbits.SMP = 1; // Input sampled at end? of data output time
#elif defined(__C30__)
ZG_SPICON1 = 0x027B; // Fcy Primary prescaler 1:1, secondary prescaler 2:1, CKP=1, CKE=0, SMP=1
ZG_SPICON2 = 0x0000;
ZG_SPISTAT = 0x8000; // Enable the module
#elif defined( __PIC32MX__ )
ZG_SPI_BRG = (GetPeripheralClock()-1ul)/2ul/ZG_MAX_SPI_FREQ;
ZG_SPICON1 = 0x00000260; // sample at end, data change idle to active, clock idle high, master
ZG_SPICON1bits.ON = 1;
#else
#error Configure SPI for the selected processor
#endif
#endif /* DEDICATED_SPI_ZG */
/* set SS low */
ZG_CS_IO = 0;
/* clear any pending interrupts */
#if defined(__18CXX)
dummy = ZG_SSPBUF;
ClearSPIDoneFlag();
#endif
// while Tx and/or Rx bytes left to handle
while (totalNumBytes > 0u)
{
#if 0
{
unsigned short i = 400; // 0x40; fails on PIC18
while(i--)
{
Nop();
Nop();
}
}
#endif
// if still outputting tx preamble bytes
if (numTxPreambleBytes > 0u)
{
--numTxPreambleBytes;
ZG_SSPBUF = *p_txPreBuf++;
}
// else if still outputting tx data bytes
else if (numTxDataBytes > 0u)
{
--numTxDataBytes;
// if outputting from RAM buffer
if (!romFlag)
{
ZG_SSPBUF = *p_txDataBuf++;
}
// else outputting from ROM buffer
else
{
ZG_SSPBUF = *p_txDataRomBuf++;
}
}
// else there were no Tx bytes to output or we are done, so just stuff an FF into SPI tx register
else
{
ZG_SSPBUF = 0xff;
}
// wait until tx/rx byte completely clocked out
WaitForDataByte();
// if still reading Rx preamble bytes
if (numRxPreambleBytes > 0u)
{
--numRxPreambleBytes;
*p_rxPreBuf++ = ZG_SSPBUF;
}
// else if still reading Rx data bytes
else if (numRxDataBytes > 0u)
{
--numRxDataBytes;
*p_rxDataBuf++ = ZG_SSPBUF;
}
// else done with Rx data
else
{
// throw away rx byte
rxTrash = ZG_SSPBUF;
}
--totalNumBytes;
} // end while
/* Disable the interrupt */
#if defined( __PIC32MX__ )
ZG_SPI_IE_CLEAR = ZG_SPI_INT_BITS;
#else
ZG_SPI_IE = 0;
#endif
/* set SS high */
ZG_CS_IO = 1;
if ( !spiSuppressDoneHandlerCall )
{
zgDriverSpiTxRxDoneHandler();
}
#ifndef DEDICATED_SPI_ZG
// Restore SPI I/O state to what it was when this function was entered
RestoreSpiContext();
#endif
return kZGBoolTrue;
}
/*****************************************************************************
Function:
void SPIFlashReadArray(uint32_t dwAddress, uint8_t *vData, uint16_t wLength)
Description:
Reads an array of bytes from the SPI Flash module.
Precondition:
SPIFlashInit has been called, and the chip is not busy (should be
handled elsewhere automatically.)
Parameters:
dwAddress - Address from which to read
vData - Where to store data that has been read
wLength - Length of data to read
Returns:
None
***************************************************************************/
void SPIFlashReadArray(uint32_t dwAddress, uint8_t *vData, uint16_t wLength)
{
volatile uint8_t Dummy;
uint8_t vSPIONSave;
#if defined(__C30__)
uint16_t SPICON1Save;
#elif defined(__C32__)
uint32_t SPICON1Save;
#endif
// Ignore operations when the destination is NULL or nothing to read
if(vData == NULL || wLength == 0)
return;
// Save SPI state (clock speed)
SPICON1Save = SPIFLASH_SPICON1;
vSPIONSave = SPI_ON_BIT;
// Configure SPI
SPI_ON_BIT = 0;
SPIFLASH_SPICON1 = PROPER_SPICON1;
SPI_ON_BIT = 1;
// Activate chip select
SPIFLASH_CS_IO = 0;
ClearSPIDoneFlag();
// Send READ opcode
SPIFLASH_SSPBUF = READ;
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
// Send address
SPIFLASH_SSPBUF = ((uint8_t*)&dwAddress)[2];
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
SPIFLASH_SSPBUF = ((uint8_t*)&dwAddress)[1];
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
SPIFLASH_SSPBUF = ((uint8_t*)&dwAddress)[0];
WaitForDataByte();
Dummy = SPIFLASH_SSPBUF;
// Read data
while(wLength--)
{
SPIFLASH_SSPBUF = 0;
WaitForDataByte();
*vData++ = SPIFLASH_SSPBUF;
}
// Deactivate chip select
SPIFLASH_CS_IO = 1;
// Restore SPI state
SPI_ON_BIT = 0;
SPIFLASH_SPICON1 = SPICON1Save;
SPI_ON_BIT = vSPIONSave;
}
