/**
* ti_sdma_start_xfer_packet - starts a packet DMA transfer
* @ch: the channel number to use for the transfer
* @src_paddr: the source physical address
* @dst_paddr: the destination physical address
* @frmcnt: the number of frames to transfer
* @elmcnt: the number of elements in a frame, an element is either an 8, 16
* or 32-bit value as defined by ti_sdma_set_xfer_burst()
* @pktsize: the number of elements in each transfer packet
*
* The @frmcnt and @elmcnt define the overall number of bytes to transfer,
* typically @frmcnt is 1 and @elmcnt contains the total number of elements.
* @pktsize is the size of each individual packet, there might be multiple
* packets per transfer. i.e. for the following with element size of 32-bits
*
* frmcnt = 1, elmcnt = 512, pktsize = 128
*
* Total transfer bytes = 1 * 512 = 512 elements or 2048 bytes
* Packets transfered = 128 / 512 = 4
*
*
* LOCKING:
* DMA registers protected by internal mutex
*
* RETURNS:
* EH_HANDLED or EH_NOT_HANDLED
*/
int
ti_sdma_start_xfer_packet(unsigned int ch, unsigned int src_paddr,
unsigned long dst_paddr, unsigned int frmcnt,
unsigned int elmcnt, unsigned int pktsize)
{
struct ti_sdma_softc *sc = ti_sdma_sc;
struct ti_sdma_channel *channel;
uint32_t ccr;
/* Sanity check */
if (sc == NULL)
return (ENOMEM);
TI_SDMA_LOCK(sc);
if ((sc->sc_active_channels & (1 << ch)) == 0) {
TI_SDMA_UNLOCK(sc);
return (EINVAL);
}
channel = &sc->sc_channel[ch];
/* a) Write the CSDP register */
if (channel->need_reg_write)
ti_sdma_write_4(sc, DMA4_CSDP(ch),
channel->reg_csdp | DMA4_CSDP_WRITE_MODE(1));
/* b) Set the number of elements to transfer CEN[23:0] */
ti_sdma_write_4(sc, DMA4_CEN(ch), elmcnt);
/* c) Set the number of frames to transfer CFN[15:0] */
ti_sdma_write_4(sc, DMA4_CFN(ch), frmcnt);
/* d) Set the Source/dest start address index CSSA[31:0]/CDSA[31:0] */
ti_sdma_write_4(sc, DMA4_CSSA(ch), src_paddr);
ti_sdma_write_4(sc, DMA4_CDSA(ch), dst_paddr);
/* e) Write the CCR register */
ti_sdma_write_4(sc, DMA4_CCR(ch),
channel->reg_ccr | DMA4_CCR_PACKET_TRANS);
/* f) - Set the source element index increment CSEI[15:0] */
ti_sdma_write_4(sc, DMA4_CSE(ch), 0x0001);
/* - Set the packet size, this is dependent on the sync source */
if (channel->reg_ccr & DMA4_CCR_SEL_SRC_DST_SYNC(1))
ti_sdma_write_4(sc, DMA4_CSF(ch), pktsize);
else
ti_sdma_write_4(sc, DMA4_CDE(ch), pktsize);
/* - Set the destination frame index increment CDFI[31:0] */
ti_sdma_write_4(sc, DMA4_CDF(ch), 0x0001);
/* Clear the status register */
ti_sdma_write_4(sc, DMA4_CSR(ch), 0x1FFE);
/* Write the start-bit and away we go */
ccr = ti_sdma_read_4(sc, DMA4_CCR(ch));
ccr |= (1 << 7);
ti_sdma_write_4(sc, DMA4_CCR(ch), ccr);
/* Clear the reg write flag */
channel->need_reg_write = 0;
TI_SDMA_UNLOCK(sc);
return (0);
}
/**
Configure OMAP DMA Channel
@param Channel DMA Channel to configure
@param Dma4 Pointer to structure used to initialize DMA registers for the Channel
@retval EFI_SUCCESS The range was mapped for the returned NumberOfBytes.
@retval EFI_INVALID_PARAMETER Channel is not valid
@retval EFI_DEVICE_ERROR The system hardware could not map the requested information.
**/
EFI_STATUS
EFIAPI
EnableDmaChannel (
IN UINTN Channel,
IN OMAP_DMA4 *DMA4
)
{
UINT32 RegVal;
if (Channel > DMA4_MAX_CHANNEL) {
return EFI_INVALID_PARAMETER;
}
/* 1) Configure the transfer parameters in the logical DMA registers */
/*-------------------------------------------------------------------*/
/* a) Set the data type CSDP[1:0], the Read/Write Port access type
CSDP[8:7]/[15:14], the Source/dest endianism CSDP[21]/CSDP[19],
write mode CSDP[17:16], source/dest packed or nonpacked CSDP[6]/CSDP[13] */
// Read CSDP
RegVal = MmioRead32 (DMA4_CSDP (Channel));
// Build reg
RegVal = ((RegVal & ~ 0x3) | DMA4->DataType );
RegVal = ((RegVal & ~(0x3 << 7)) | (DMA4->ReadPortAccessType << 7));
RegVal = ((RegVal & ~(0x3 << 14)) | (DMA4->WritePortAccessType << 14));
RegVal = ((RegVal & ~(0x1 << 21)) | (DMA4->SourceEndiansim << 21));
RegVal = ((RegVal & ~(0x1 << 19)) | (DMA4->DestinationEndianism << 19));
RegVal = ((RegVal & ~(0x3 << 16)) | (DMA4->WriteMode << 16));
RegVal = ((RegVal & ~(0x1 << 6)) | (DMA4->SourcePacked << 6));
RegVal = ((RegVal & ~(0x1 << 13)) | (DMA4->DestinationPacked << 13));
// Write CSDP
MmioWrite32 (DMA4_CSDP (Channel), RegVal);
/* b) Set the number of element per frame CEN[23:0]*/
MmioWrite32 (DMA4_CEN (Channel), DMA4->NumberOfElementPerFrame);
/* c) Set the number of frame per block CFN[15:0]*/
MmioWrite32 (DMA4_CFN (Channel), DMA4->NumberOfFramePerTransferBlock);
/* d) Set the Source/dest start address index CSSA[31:0]/CDSA[31:0]*/
MmioWrite32 (DMA4_CSSA (Channel), DMA4->SourceStartAddress);
MmioWrite32 (DMA4_CDSA (Channel), DMA4->DestinationStartAddress);
/* e) Set the Read Port addressing mode CCR[13:12], the Write Port addressing mode CCR[15:14],
read/write priority CCR[6]/CCR[26]
I changed LCH CCR[20:19]=00 and CCR[4:0]=00000 to
LCH CCR[20:19]= DMA4->WriteRequestNumber and CCR[4:0]=DMA4->ReadRequestNumber
*/
// Read CCR
RegVal = MmioRead32 (DMA4_CCR (Channel));
// Build reg
RegVal = ((RegVal & ~0x1f) | DMA4->ReadRequestNumber);
RegVal = ((RegVal & ~(BIT20 | BIT19)) | DMA4->WriteRequestNumber << 19);
RegVal = ((RegVal & ~(0x3 << 12)) | (DMA4->ReadPortAccessMode << 12));
RegVal = ((RegVal & ~(0x3 << 14)) | (DMA4->WritePortAccessMode << 14));
RegVal = ((RegVal & ~(0x1 << 6)) | (DMA4->ReadPriority << 6));
RegVal = ((RegVal & ~(0x1 << 26)) | (DMA4->WritePriority << 26));
// Write CCR
MmioWrite32 (DMA4_CCR (Channel), RegVal);
/* f)- Set the source element index CSEI[15:0]*/
MmioWrite32 (DMA4_CSEI (Channel), DMA4->SourceElementIndex);
/* - Set the source frame index CSFI[15:0]*/
MmioWrite32 (DMA4_CSFI (Channel), DMA4->SourceFrameIndex);
/* - Set the destination element index CDEI[15:0]*/
MmioWrite32 (DMA4_CDEI (Channel), DMA4->DestinationElementIndex);
/* - Set the destination frame index CDFI[31:0]*/
MmioWrite32 (DMA4_CDFI (Channel), DMA4->DestinationFrameIndex);
MmioWrite32 (DMA4_CDFI (Channel), DMA4->DestinationFrameIndex);
// Enable all the status bits since we are polling
MmioWrite32 (DMA4_CICR (Channel), DMA4_CICR_ENABLE_ALL);
MmioWrite32 (DMA4_CSR (Channel), DMA4_CSR_RESET);
/* 2) Start the DMA transfer by Setting the enable bit CCR[7]=1 */
/*--------------------------------------------------------------*/
//write enable bit
MmioOr32 (DMA4_CCR(Channel), DMA4_CCR_ENABLE); //Launch transfer
return EFI_SUCCESS;
}
