int
main(void)
{
wdt_disable();
// un-reset ethernet
ENC28J60_RESET_DDR |= _BV( ENC28J60_RESET_BIT );
ENC28J60_RESET_PORT |= _BV( ENC28J60_RESET_BIT );
led_init();
LED_ON();
spi_init();
eeprom_init();
// if we had been restarted by watchdog check the REQ BootLoader byte in the
// EEPROM ...
if(bit_is_set(MCUSR,WDRF) && eeprom_read_byte(EE_REQBL)) {
eeprom_write_byte( EE_REQBL, 0 ); // clear flag
// TBD: This is useless as button needs to be pressed - needs moving into bootloader directly
// start_bootloader();
}
// Setup OneWire and make a full search at the beginning (takes some time)
#ifdef HAS_ONEWIRE
i2c_init();
onewire_Init();
onewire_FullSearch();
#endif
// Setup the timers. Are needed for watchdog-reset
#if defined (HAS_IRRX) || defined (HAS_IRTX)
ir_init();
// IR uses highspeed TIMER0 for sampling
OCR0A = 1; // Timer0: 0.008s = 8MHz/256/2 == 15625Hz
#else
OCR0A = 249; // Timer0: 0.008s = 8MHz/256/250 == 125Hz
#endif
TCCR0B = _BV(CS02);
TCCR0A = _BV(WGM01);
TIMSK0 = _BV(OCIE0A);
TCCR1A = 0;
TCCR1B = _BV(CS11) | _BV(WGM12); // Timer1: 1us = 8MHz/8
clock_prescale_set(clock_div_1);
MCUSR &= ~(1 << WDRF); // Enable the watchdog
wdt_enable(WDTO_2S);
uart_init( UART_BAUD_SELECT_DOUBLE_SPEED(UART_BAUD_RATE,F_CPU) );
fht_init();
tx_init();
input_handle_func = analyze_ttydata;
#ifdef HAS_RF_ROUTER
rf_router_init();
display_channel = (DISPLAY_USB|DISPLAY_RFROUTER);
#else
display_channel = DISPLAY_USB;
#endif
ethernet_init();
LED_OFF();
sei();
for(;;) {
uart_task();
RfAnalyze_Task();
Minute_Task();
#ifdef HAS_FASTRF
FastRF_Task();
#endif
#ifdef HAS_RF_ROUTER
rf_router_task();
#endif
#ifdef HAS_ASKSIN
rf_asksin_task();
#endif
#ifdef HAS_IRRX
ir_task();
#endif
#ifdef HAS_ETHERNET
Ethernet_Task();
#endif
}
}
int
main(void)
{
wdt_disable();
#ifdef HAS_16MHZ_CLOCK
/* set clock to 16MHz/2 = 8Mhz */
clock_prescale_set(clock_div_2);
#endif
// LED_ON_DDR |= _BV( LED_ON_PIN );
// LED_ON_PORT |= _BV( LED_ON_PIN );
led_init();
LED_ON();
spi_init();
// init_adcw();
//eeprom_factory_reset("xx");
eeprom_init();
// Setup the timers. Are needed for watchdog-reset
OCR0A = 249; // Timer0: 0.008s = 8MHz/256/250 == 125Hz
TCCR0B = _BV(CS02);
TCCR0A = _BV(WGM01);
TIMSK0 = _BV(OCIE0A);
TCCR1A = 0;
TCCR1B = _BV(CS11) | _BV(WGM12); // Timer1: 1us = 8MHz/8
MCUSR &= ~(1 << WDRF); // Enable the watchdog
wdt_enable(WDTO_2S);
#ifdef HAS_16MHZ_CLOCK
uart_init( UART_BAUD_SELECT(UART_BAUD_RATE,F_CPU) );
#else
uart_init( UART_BAUD_SELECT_DOUBLE_SPEED(UART_BAUD_RATE,F_CPU) );
#endif
fht_init();
tx_init();
input_handle_func = analyze_ttydata;
display_channel = DISPLAY_USB;
#ifdef HAS_RF_ROUTER
rf_router_init();
display_channel |= DISPLAY_RFROUTER;
#endif
LED_OFF();
sei();
for(;;) {
uart_task();
RfAnalyze_Task();
Minute_Task();
#ifdef HAS_FASTRF
FastRF_Task();
#endif
#ifdef HAS_RF_ROUTER
rf_router_task();
#endif
#ifdef HAS_ASKSIN
rf_asksin_task();
#endif
#ifdef HAS_MORITZ
rf_moritz_task();
#endif
#ifdef HAS_RWE
rf_rwe_task();
#endif
#ifdef HAS_MBUS
rf_mbus_task();
#endif
}
}
int
main(void)
{
wdt_disable();
#ifdef CSMV4
LED_ON_DDR |= _BV( LED_ON_PIN );
LED_ON_PORT |= _BV( LED_ON_PIN );
#endif
led_init();
LED_ON();
spi_init();
// eeprom_factory_reset("xx");
eeprom_init();
// led_mode = 2;
// if we had been restarted by watchdog check the REQ BootLoader byte in the
// EEPROM ...
// if(bit_is_set(MCUSR,WDRF) && eeprom_read_byte(EE_REQBL)) {
// eeprom_write_byte( EE_REQBL, 0 ); // clear flag
// start_bootloader();
// }
// Setup the timers. Are needed for watchdog-reset
#ifdef HAS_IRRX
ir_init();
// IR uses highspeed TIMER0 for sampling
OCR0A = 1; // Timer0: 0.008s = 8MHz/256/2 == 15625Hz
#else
OCR0A = 249; // Timer0: 0.008s = 8MHz/256/250 == 125Hz
#endif
TCCR0B = _BV(CS02);
TCCR0A = _BV(WGM01);
TIMSK0 = _BV(OCIE0A);
TCCR1A = 0;
TCCR1B = _BV(CS11) | _BV(WGM12); // Timer1: 1us = 8MHz/8
clock_prescale_set(clock_div_1);
MCUSR &= ~(1 << WDRF); // Enable the watchdog
wdt_enable(WDTO_2S);
uart_init( UART_BAUD_SELECT_DOUBLE_SPEED(UART_BAUD_RATE,F_CPU) );
#ifdef HAS_DOGM
dogm_init();
#endif
fht_init();
tx_init();
input_handle_func = analyze_ttydata;
display_channel = DISPLAY_USB;
#ifdef HAS_RF_ROUTER
rf_router_init();
display_channel |= DISPLAY_RFROUTER;
#endif
#ifdef HAS_DOGM
display_channel |= DISPLAY_DOGM;
#endif
LED_OFF();
sei();
for(;;) {
uart_task();
RfAnalyze_Task();
Minute_Task();
#ifdef HAS_FASTRF
FastRF_Task();
#endif
#ifdef HAS_RF_ROUTER
rf_router_task();
#endif
#ifdef HAS_ASKSIN
rf_asksin_task();
#endif
#ifdef HAS_MORITZ
rf_moritz_task();
#endif
#ifdef HAS_IRRX
ir_task();
#endif
}
}
int
main(void)
{
wdt_disable();
clock_prescale_set(clock_div_1);
LED_ON_DDR |= _BV( LED_ON_PIN );
LED_ON_PORT |= _BV( LED_ON_PIN );
led_init();
LED_ON();
spi_init();
// eeprom_factory_reset("xx");
eeprom_init();
// Setup OneWire and make a full search at the beginning (takes some time)
#ifdef HAS_ONEWIRE
i2c_init();
onewire_Init();
onewire_FullSearch();
#endif
// Setup the timers. Are needed for watchdog-reset
#if defined (HAS_IRRX) || defined (HAS_IRTX)
ir_init();
// IR uses highspeed TIMER0 for sampling
OCR0A = 1; // Timer0: 0.008s = 8MHz/256/2 == 15625Hz
#else
OCR0A = 249; // Timer0: 0.008s = 8MHz/256/250 == 125Hz
#endif
TCCR0B = _BV(CS02);
TCCR0A = _BV(WGM01);
TIMSK0 = _BV(OCIE0A);
TCCR1A = 0;
TCCR1B = _BV(CS11) | _BV(WGM12); // Timer1: 1us = 8MHz/8
MCUSR &= ~(1 << WDRF); // Enable the watchdog
wdt_enable(WDTO_2S);
uart_init( UART_BAUD_SELECT_DOUBLE_SPEED(UART_BAUD_RATE,F_CPU) );
fht_init();
tx_init();
input_handle_func = analyze_ttydata;
display_channel = DISPLAY_USB;
#ifdef HAS_RF_ROUTER
rf_router_init();
display_channel |= DISPLAY_RFROUTER;
#endif
checkFrequency();
LED_OFF();
sei();
for(;;) {
uart_task();
RfAnalyze_Task();
Minute_Task();
#ifdef HAS_FASTRF
FastRF_Task();
#endif
#ifdef HAS_RF_ROUTER
rf_router_task();
#endif
#ifdef HAS_ASKSIN
rf_asksin_task();
#endif
#ifdef HAS_MORITZ
rf_moritz_task();
#endif
#ifdef HAS_RWE
rf_rwe_task();
#endif
#if defined(HAS_IRRX) || defined(HAS_IRTX)
ir_task();
#endif
#ifdef HAS_MBUS
rf_mbus_task();
#endif
}
}
int
main(void)
{
// wdt_disable();
clock_prescale_set(clock_div_1);
MARK433_PORT |= _BV( MARK433_BIT ); // Pull 433MHz marker
MARK915_PORT |= _BV( MARK915_BIT ); // Pull 915MHz marker
led_init();
spi_init();
// Setup the timers. Are needed for watchdog-reset
OCR0A = 249; // Timer0: 0.008s = 8MHz/256/250 == 125Hz
TCCR0B = _BV(CS02);
TCCR0A = _BV(WGM01);
TIMSK0 = _BV(OCIE0A);
TCCR1A = 0;
TCCR1B = _BV(CS11) | _BV(WGM12); // Timer1: 1us = 8MHz/8
//eeprom_factory_reset("xx");
eeprom_init();
MCUSR &= ~(1 << WDRF); // Enable the watchdog
wdt_enable(WDTO_2S);
//uart_init( UART_BAUD_SELECT_DOUBLE_SPEED(UART_BAUD_RATE,F_CPU) );
uart_init( UART_BAUD_SELECT_DOUBLE_SPEED(UART_BAUD_RATE,F_CPU) );
fht_init();
tx_init();
input_handle_func = analyze_ttydata;
display_channel = DISPLAY_USB;
#ifdef HAS_RF_ROUTER
rf_router_init();
display_channel |= DISPLAY_RFROUTER;
#endif
checkFrequency();
sei();
for(;;) {
uart_task();
RfAnalyze_Task();
Minute_Task();
#ifdef HAS_FASTRF
FastRF_Task();
#endif
#ifdef HAS_RF_ROUTER
rf_router_task();
#endif
#ifdef HAS_ASKSIN
rf_asksin_task();
#endif
#ifdef HAS_MORITZ
rf_moritz_task();
#endif
#ifdef HAS_RWE
rf_rwe_task();
#endif
#ifdef HAS_RFNATIVE
native_task();
#endif
#ifdef HAS_KOPP_FC
kopp_fc_task();
#endif
#ifdef HAS_MBUS
rf_mbus_task();
#endif
#ifdef HAS_ZWAVE
rf_zwave_task();
#endif
}
}
//------------------------------------------------------------------------------
/// Application entry point. Configures the DBGU, PIT, TC0, LEDs and buttons
/// and makes LED\#1 blink in its infinite loop, using the Wait function.
/// \return Unused (ANSI-C compatibility).
//------------------------------------------------------------------------------
int main(void)
{
// DBGU configuration
TRACE_CONFIGURE(DBGU_STANDARD, 115200, BOARD_MCK);
TRACE_INFO_WP("\n\r");
TRACE_INFO("Getting new Started Project --\n\r");
TRACE_INFO("%s\n\r", BOARD_NAME);
TRACE_INFO("Compiled: %s %s --\n\r", __DATE__, __TIME__);
//Configure Reset Controller
AT91C_BASE_RSTC->RSTC_RMR= 0xa5<<24;
// Configure EMAC PINS
PIO_Configure(emacRstPins, PIO_LISTSIZE(emacRstPins));
// Execute reset
RSTC_SetExtResetLength(0xd);
RSTC_ExtReset();
// Wait for end hardware reset
while (!RSTC_GetNrstLevel());
TRACE_INFO("init Flash\n\r");
flash_init();
TRACE_INFO("init Timer\n\r");
// Configure timer 0
ticks=0;
extern void ISR_Timer0();
AT91C_BASE_PMC->PMC_PCER = (1 << AT91C_ID_TC0);
AT91C_BASE_TC0->TC_CCR = AT91C_TC_CLKDIS;
AT91C_BASE_TC0->TC_IDR = 0xFFFFFFFF;
AT91C_BASE_TC0->TC_SR;
AT91C_BASE_TC0->TC_CMR = AT91C_TC_CLKS_TIMER_DIV5_CLOCK | AT91C_TC_CPCTRG;
AT91C_BASE_TC0->TC_RC = 375;
AT91C_BASE_TC0->TC_IER = AT91C_TC_CPCS;
AIC_ConfigureIT(AT91C_ID_TC0, AT91C_AIC_PRIOR_LOWEST, ISR_Timer0);
AIC_EnableIT(AT91C_ID_TC0);
AT91C_BASE_TC0->TC_CCR = AT91C_TC_CLKEN | AT91C_TC_SWTRG;
// Configure timer 1
extern void ISR_Timer1();
AT91C_BASE_PMC->PMC_PCER = (1 << AT91C_ID_TC1);
AT91C_BASE_TC1->TC_CCR = AT91C_TC_CLKDIS; //Stop clock
AT91C_BASE_TC1->TC_IDR = 0xFFFFFFFF; //Disable Interrupts
AT91C_BASE_TC1->TC_SR; //Read Status register
AT91C_BASE_TC1->TC_CMR = AT91C_TC_CLKS_TIMER_DIV4_CLOCK | AT91C_TC_CPCTRG; // Timer1: 2,666us = 48MHz/128
AT91C_BASE_TC1->TC_RC = 0xffff;
AT91C_BASE_TC1->TC_IER = AT91C_TC_CPCS;
AIC_ConfigureIT(AT91C_ID_TC1, 1, ISR_Timer1);
AT91C_BASE_TC1->TC_CCR = AT91C_TC_CLKEN | AT91C_TC_SWTRG;
led_init();
TRACE_INFO("init EEprom\n\r");
eeprom_init();
rb_reset(&TTY_Rx_Buffer);
rb_reset(&TTY_Tx_Buffer);
input_handle_func = analyze_ttydata;
LED_OFF();
LED2_OFF();
LED3_OFF();
spi_init();
fht_init();
tx_init();
#ifdef HAS_ETHERNET
ethernet_init();
#endif
TRACE_INFO("init USB\n\r");
CDCDSerialDriver_Initialize();
USBD_Connect();
wdt_enable(WDTO_2S);
fastrf_on=0;
display_channel = DISPLAY_USB;
TRACE_INFO("init Complete\n\r");
checkFrequency();
// Main loop
while (1) {
CDC_Task();
Minute_Task();
RfAnalyze_Task();
#ifdef HAS_FASTRF
FastRF_Task();
#endif
#ifdef HAS_RF_ROUTER
rf_router_task();
#endif
#ifdef HAS_ASKSIN
rf_asksin_task();
#endif
#ifdef HAS_MORITZ
rf_moritz_task();
#endif
#ifdef HAS_RWE
rf_rwe_task();
#endif
#ifdef HAS_MBUS
rf_mbus_task();
#endif
#ifdef HAS_MAICO
rf_maico_task();
#endif
#ifdef HAS_ETHERNET
Ethernet_Task();
#endif
#ifdef DBGU_UNIT_IN
if(DBGU_IsRxReady()){
unsigned char volatile * const ram = (unsigned char *) AT91C_ISRAM;
unsigned char x;
x=DBGU_GetChar();
switch(x) {
case 'd':
puts("USB disconnect\n\r");
USBD_Disconnect();
break;
case 'c':
USBD_Connect();
puts("USB Connect\n\r");
break;
case 'r':
//Configure Reset Controller
AT91C_BASE_RSTC->RSTC_RMR=AT91C_RSTC_URSTEN | 0xa5<<24;
break;
case 'S':
USBD_Disconnect();
my_delay_ms(250);
my_delay_ms(250);
//Reset
*ram = 0xaa;
AT91C_BASE_RSTC->RSTC_RCR = AT91C_RSTC_PROCRST | AT91C_RSTC_PERRST | AT91C_RSTC_EXTRST | 0xA5<<24;
while (1);
break;
default:
rb_put(&TTY_Tx_Buffer, x);
}
}
#endif
if (USBD_GetState() == USBD_STATE_CONFIGURED) {
if( USBState == STATE_IDLE ) {
CDCDSerialDriver_Read(usbBuffer,
DATABUFFERSIZE,
(TransferCallback) UsbDataReceived,
0);
LED3_ON();
USBState=STATE_RX;
}
}
if( USBState == STATE_SUSPEND ) {
TRACE_INFO("suspend !\n\r");
USBState = STATE_IDLE;
}
if( USBState == STATE_RESUME ) {
TRACE_INFO("resume !\n\r");
USBState = STATE_IDLE;
}
}
}
int
main(void)
{
wdt_enable(WDTO_2S);
#if defined(CUL_ARDUINO)
clock_prescale_set(clock_div_1); // for 8MHz clock div schould be 1
#endif
MARK433_PORT |= _BV( MARK433_BIT ); // Pull 433MHz marker
MARK915_PORT |= _BV( MARK915_BIT ); // Pull 915MHz marker
// if we had been restarted by watchdog check the REQ BootLoader byte in the
// EEPROM ...
if(bit_is_set(MCUSR,WDRF) && erb(EE_REQBL)) {
ewb( EE_REQBL, 0 ); // clear flag
start_bootloader();
}
// Setup the timers. Are needed for watchdog-reset
OCR0A = 249; // Timer0: 0.008s = 8MHz/256/250
TCCR0B = _BV(CS02);
TCCR0A = _BV(WGM01);
TIMSK0 = _BV(OCIE0A);
TCCR1A = 0;
TCCR1B = _BV(CS11) | _BV(WGM12); // Timer1: 1us = 8MHz/8
MCUSR &= ~(1 << WDRF); // Enable the watchdog
led_init();
spi_init();
eeprom_init();
USB_Init();
fht_init();
tx_init();
input_handle_func = analyze_ttydata;
#ifdef HAS_RF_ROUTER
rf_router_init();
display_channel = (DISPLAY_USB|DISPLAY_RFROUTER);
#else
display_channel = DISPLAY_USB;
#endif
checkFrequency();
LED_OFF();
for(;;) {
USB_USBTask();
CDC_Task();
RfAnalyze_Task();
Minute_Task();
#ifdef HAS_FASTRF
FastRF_Task();
#endif
#ifdef HAS_RF_ROUTER
rf_router_task();
#endif
#ifdef HAS_ASKSIN
rf_asksin_task();
#endif
#ifdef HAS_MORITZ
rf_moritz_task();
#endif
#ifdef HAS_RWE
rf_rwe_task();
#endif
#ifdef HAS_RFNATIVE
native_task();
#endif
#ifdef HAS_KOPP_FC
kopp_fc_task();
#endif
#ifdef HAS_MBUS
rf_mbus_task();
#endif
#ifdef HAS_ZWAVE
rf_zwave_task();
#endif
}
}
int
main(void)
{
wdt_disable();
led_init();
LED_ON();
MARK433_PORT |= _BV( MARK433_BIT );
MARK915_PORT |= _BV( MARK915_BIT );
spi_init();
// eeprom_factory_reset("xx");
eeprom_init();
// led_mode = 2;
// if we had been restarted by watchdog check the REQ BootLoader byte in the
// EEPROM ...
// if(bit_is_set(MCUSR,WDRF) && eeprom_read_byte(EE_REQBL)) {
// eeprom_write_byte( EE_REQBL, 0 ); // clear flag
// start_bootloader();
// }
// Setup the timers. Are needed for watchdog-reset
OCR0A = 249; // Timer0: 0.008s = 8MHz/256/250 == 125Hz
TCCR0B = _BV(CS02);
TCCR0A = _BV(WGM01);
TIMSK0 = _BV(OCIE0A);
TCCR1A = 0;
TCCR1B = _BV(CS11) | _BV(WGM12); // Timer1: 1us = 8MHz/8
clock_prescale_set(clock_div_1);
MCUSR &= ~(1 << WDRF); // Enable the watchdog
wdt_enable(WDTO_2S);
uart_init( UART_BAUD_SELECT_DOUBLE_SPEED(UART_BAUD_RATE,F_CPU) );
#ifdef HAS_STACKING
stacking_initialize();
// make sure i2c is inactive
DDRC &= 0xfc;
PORTC &= 0xfc;
#endif
fht_init();
tx_init();
input_handle_func = analyze_ttydata;
display_channel = DISPLAY_USB;
#ifdef HAS_RF_ROUTER
rf_router_init();
display_channel |= DISPLAY_RFROUTER;
#endif
LED_OFF();
checkFrequency();
sei();
for(;;) {
uart_task();
RfAnalyze_Task();
Minute_Task();
#ifdef HAS_FASTRF
FastRF_Task();
#endif
#ifdef HAS_RF_ROUTER
rf_router_task();
#endif
#ifdef HAS_ASKSIN
rf_asksin_task();
#endif
#ifdef HAS_MORITZ
rf_moritz_task();
#endif
#ifdef HAS_STACKING
stacking_task();
#endif
#ifdef HAS_MBUS
rf_mbus_task();
#endif
}
}
int
main(void)
{
wdt_disable();
// un-reset ethernet
ENC28J60_RESET_DDR |= _BV( ENC28J60_RESET_BIT );
ENC28J60_RESET_PORT |= _BV( ENC28J60_RESET_BIT );
MARK433_PORT |= _BV( MARK433_BIT ); // Pull 433MHz marker
MARK915_PORT |= _BV( MARK915_BIT ); // Pull 915MHz marker
led_init();
LED_ON();
spi_init();
eeprom_init();
// Reset the "Request Bootloader" flag in EEPROM, to avoid a permanent loop
eeprom_update_byte( EE_REQBL, 0);
// Setup OneWire and make a full search at the beginning (takes some time)
#ifdef HAS_ONEWIRE
i2c_init();
onewire_Init();
onewire_FullSearch();
#endif
// Setup the timers. Are needed for watchdog-reset
#if defined (HAS_IRRX) || defined (HAS_IRTX)
ir_init();
// IR uses highspeed TIMER0 for sampling
OCR0A = 1; // Timer0: 0.008s = 8MHz/256/2 == 15625Hz Fac: 125
#else
OCR0A = 249; // Timer0: 0.008s = 8MHz/256/250 == 125Hz
#endif
TCCR0B = _BV(CS02);
TCCR0A = _BV(WGM01);
TIMSK0 = _BV(OCIE0A);
TCCR1A = 0;
TCCR1B = _BV(CS11) | _BV(WGM12); // Timer1: 1us = 8MHz/8
clock_prescale_set(clock_div_1);
MCUSR &= ~(1 << WDRF); // Enable the watchdog
wdt_enable(WDTO_2S);
uart_init( UART_BAUD_SELECT_DOUBLE_SPEED(UART_BAUD_RATE,F_CPU) );
fht_init();
tx_init();
input_handle_func = analyze_ttydata;
#ifdef HAS_RF_ROUTER
rf_router_init();
display_channel = (DISPLAY_USB|DISPLAY_RFROUTER);
#else
display_channel = DISPLAY_USB;
#endif
#ifdef HAS_VZ
vz_init();
#endif
ethernet_init();
LED_OFF();
#ifdef HAS_DMX
#ifdef DMX_CHANNELS
dmx_initialize(DMX_CHANNELS);
#else
dmx_initialize(16);
#endif
#endif
#ifdef HAS_HM485
hm485_initialize();
#endif
#ifdef HAS_HELIOS
helios_initialize();
#endif
#ifdef HAS_CUNOTTY
rf_cunotty_init();
#endif
sei();
#ifdef HAS_DMX
dmx_start();
#endif
for(;;) {
uart_task();
RfAnalyze_Task();
Minute_Task();
#ifdef HAS_FASTRF
FastRF_Task();
#endif
#ifdef HAS_RF_ROUTER
rf_router_task();
#endif
#ifdef HAS_CUNOTTY
rf_cunotty_task();
#endif
#ifdef HAS_ASKSIN
rf_asksin_task();
#endif
#ifdef HAS_IRRX
ir_task();
#endif
#ifdef HAS_ETHERNET
Ethernet_Task();
#endif
#ifdef HAS_VZ
vz_task();
#endif
#ifdef HAS_MORITZ
rf_moritz_task();
#endif
#ifdef HAS_HM485
hm485_task();
#endif
#ifdef HAS_HELIOS
helios_task();
#endif
}
}
int
main(void)
{
wdt_enable(WDTO_2S);
clock_prescale_set(clock_div_1); // Disable Clock Division
// if we had been restarted by watchdog check the REQ BootLoader byte in the
// EEPROM ...
if (bit_is_set(MCUSR,WDRF) && erb(EE_REQBL)) {
ewb( EE_REQBL, 0 ); // clear flag
start_bootloader();
}
// Setup the timers. Are needed for watchdog-reset
OCR0A = 249; // Timer0: 0.008s = 8MHz/256/250
TCCR0B = _BV(CS02);
TCCR0A = _BV(WGM01);
TIMSK0 = _BV(OCIE0A);
TCCR1A = 0;
TCCR1B = _BV(CS11) | _BV(WGM12); // Timer1: 1us = 8MHz/8
#ifdef CURV3
// Timer3 is used by the LCD backlight (PWM)
TCCR3A = _BV(COM3A1)| _BV(WGM30); // Fast PWM, 8-bit, clear on match
TCCR3B = _BV(WGM32) | _BV(CS31); // Prescaler 8MHz/8: 3.9KHz
#endif
MCUSR &= ~(1 << WDRF); // Enable the watchdog
led_init();
spi_init();
eeprom_init();
USB_Init();
fht_init();
tx_init();
joy_init(); // lcd init is done manually from menu_init
bat_init();
df_init(&df);
fs_init(&fs, df, 0); // needs df_init
rtc_init(); // does i2c_init too
log_init(); // needs fs_init & rtc_init
menu_init(); // needs fs_init
input_handle_func = analyze_ttydata;
log_enabled = erb(EE_LOGENABLED);
display_channel = DISPLAY_USB|DISPLAY_LCD|DISPLAY_RFROUTER;
rf_router_init();
checkFrequency();
LED_OFF();
for(;;) {
USB_USBTask();
CDC_Task();
RfAnalyze_Task();
Minute_Task();
FastRF_Task();
rf_router_task();
JOY_Task();
}
}
int
main(void)
{
//ewb((uint8_t*)0x80, erb((uint8_t*)0x80)+1);
wdt_enable(WDTO_2S); // Avoid an early reboot
clock_prescale_set(clock_div_1); // Disable Clock Division:1->8MHz
#ifdef HAS_XRAM
init_memory_mapped(); // First initialize the RAM
#endif
// if we had been restarted by watchdog check the REQ BootLoader byte in the
// EEPROM
if(bit_is_set(MCUSR,WDRF) && erb(EE_REQBL)) {
ewb( EE_REQBL, 0 ); // clear flag
start_bootloader();
}
while(tx_report); // reboot if the bss is not initialized
// Setup the timers. Are needed for watchdog-reset
OCR0A = 249; // Timer0: 0.008s = 8MHz/256/250
TCCR0B = _BV(CS02);
TCCR0A = _BV(WGM01);
TIMSK0 = _BV(OCIE0A);
TCCR1A = 0;
TCCR1B = _BV(CS11) | _BV(WGM12); // Timer1: 1us = 8MHz/8
MCUSR &= ~(1 << WDRF); // Enable the watchdog
led_init(); // So we can debug
spi_init();
eeprom_init();
USB_Init();
fht_init();
tx_init();
ethernet_init();
#ifdef HAS_FS
df_init(&df);
fs_init(&fs, df, 0); // needs df_init
log_init(); // needs fs_init & rtc_init
log_enabled = erb(EE_LOGENABLED);
#endif
input_handle_func = analyze_ttydata;
display_channel = DISPLAY_USB;
LED_OFF();
for(;;) {
USB_USBTask();
CDC_Task();
RfAnalyze_Task();
Minute_Task();
FastRF_Task();
rf_router_task();
#ifdef HAS_ASKSIN
rf_asksin_task();
#endif
#ifdef HAS_ETHERNET
Ethernet_Task();
#endif
}
}