void EcuM_Callout_DriverInitListTwo(void)
{
/* status of NvM initialization */
NvM_RequestResultType Result;
BswM_Init(BswM_ConfigPtr);
Fls_Init(NULL_PTR);
#ifdef BASE_EA_ENABLED
EA_INIT_FUNC();
#endif
#ifdef BASE_FEE_ENABLED
FEE_INIT_FUNC();
/* wait for FEE to complete the init sequence */
do
{
Fee_MainFunction();
Fls_MainFunction();
}
while (MEMIF_IDLE != Fee_GetStatus());
#endif
#ifdef BASE_NVM_ENABLED
NVM_INIT_FUNC();
NvM_ReadAll();
/* wait for the NvM_ReadAll() to complete - some of the remaining
modules need valid NvRam data... */
do
{
NvM_MainFunction();
Fee_MainFunction();
Fls_MainFunction();
(void)NvM_GetErrorStatus(NvMConf_NvMBlockDescriptor_NvMBlock_ConfigID, &Result);
}
while (Result == NVM_REQ_PENDING);
#endif
LinEmuUart_Init();
Can_InitMemory();
Can_Init(&CanConfigSet);
CanIf_InitMemory();
CanIf_Init(&CanIf_Config);
//CanNm_Init(&CanNmGlobalConfig);
//Nm_Init(&Nm_Configuration0);
PduR_InitMemory();
PduR_Init(&PduRGlobalConfig);
Com_InitMemory();
Com_Init(&ComConfig);
CanSM_InitMemory();
CanSM_Init();
CanTp_InitMemory();
CanTp_Init();
ComM_InitMemory();
ComM_Init(&ComMConfig);
Xcp_Init(NULL);
FiM_Init(&FiM_Config_0);
DiagMeas_Init();
DiagCtrl_Init();
SCI_B6Bridge_Init();
SCI_Pfc_Init();
SCI_IOHW_Init();
#ifdef BASE_DEM_ENABLED
DEM_INIT_FUNC();
/* start the standard operation cycle */
/* (void) Dem_SetOperationCycleState(DEM_OPCYC_POWER, DEM_CYCLE_STATE_START); */
#endif
Dcm_Init();
}
/*
* The order defined here is found in 3.1.5/EcuM2411
*/
void EcuM_StartupTwo(void)
{
//TODO: Validate that we are in state STARTUP_ONE.
#if defined(USE_NVM)
extern CounterType Os_Arc_OsTickCounter;
TickType tickTimerStart, tickTimerElapsed;
static NvM_RequestResultType readAllResult;
TickType tickTimer;
StatusType tickTimerStatus;
#endif
set_current_state(ECUM_STATE_STARTUP_TWO);
// Initialize the BSW scheduler
#if defined(USE_SCHM)
SchM_Init();
#endif
#if defined(USE_WDGM)
if( EcuM_World.config->EcuMWdgMConfig != NULL ) {
WdgM_SetMode(EcuM_World.config->EcuMWdgMConfig->EcuMWdgMStartupMode);
}
#endif
// Initialize drivers that don't need NVRAM data
EcuM_AL_DriverInitTwo(EcuM_World.config);
#if defined(USE_NVM)
// Start timer to wait for NVM job to complete
tickTimerStart = GetOsTick();
#endif
// Prepare the system to startup RTE
// TODO EcuM_OnRTEStartup();
#if defined(USE_RTE)
Rte_Start();
#endif
#if defined(USE_NVM)
/* Wait for the NVM job (NvM_ReadAll) to terminate. This assumes that:
* - A task runs the memory MainFunctions, e.g. Ea_MainFunction(), Eep_MainFunction()
* are run in a higher priority task that the task that executes this code.
*/
do {
#if defined(__GTK__)
#ifdef USE_FEE
Fls_MainFunction();
Fee_MainFunction();
#endif
#ifdef USE_EA
Eep_MainFunction();
Ea_MainFunction();
#endif
NvM_MainFunction();
#endif
/* Read the multiblock status */
NvM_GetErrorStatus(0, &readAllResult);
tickTimerElapsed = OS_TICKS2MS_OS_TICK(GetOsTick() - tickTimerStart);
/* The timeout EcuMNvramReadAllTimeout is in ms */
} while( (readAllResult == NVM_REQ_PENDING) && (tickTimerElapsed < EcuM_World.config->EcuMNvramReadAllTimeout) );
#endif
// Initialize drivers that need NVRAM data
EcuM_AL_DriverInitThree(EcuM_World.config);
// TODO: Indicate mode change to RTE
EcuM_enter_run_mode();
}
