/**
* @brief Initialize some features of ADC group regular.
* @note These parameters have an impact on ADC scope: ADC group regular.
* Refer to corresponding unitary functions into
* @ref ADC_LL_EF_Configuration_ADC_Group_Regular
* (functions with prefix "REG").
* @note The setting of these parameters by function @ref LL_ADC_Init()
* is conditioned to ADC state:
* ADC instance must be disabled.
* This condition is applied to all ADC features, for efficiency
* and compatibility over all STM32 families. However, the different
* features can be set under different ADC state conditions
* (setting possible with ADC enabled without conversion on going,
* ADC enabled with conversion on going, ...)
* Each feature can be updated afterwards with a unitary function
* and potentially with ADC in a different state than disabled,
* refer to description of each function for setting
* conditioned to ADC state.
* @note After using this function, other features must be configured
* using LL unitary functions.
* The minimum configuration remaining to be done is:
* - Set ADC group regular sequencer:
* map channel on rank corresponding to channel number.
* Refer to function @ref LL_ADC_REG_SetSequencerChannels();
* - Set ADC channel sampling time
* Refer to function LL_ADC_SetChannelSamplingTime();
* @param ADCx ADC instance
* @param ADC_REG_InitStruct Pointer to a @ref LL_ADC_REG_InitTypeDef structure
* @retval An ErrorStatus enumeration value:
* - SUCCESS: ADC registers are initialized
* - ERROR: ADC registers are not initialized
*/
ErrorStatus LL_ADC_REG_Init(ADC_TypeDef *ADCx, LL_ADC_REG_InitTypeDef *ADC_REG_InitStruct)
{
ErrorStatus status = SUCCESS;
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(ADCx));
assert_param(IS_LL_ADC_REG_TRIG_SOURCE(ADC_REG_InitStruct->TriggerSource));
assert_param(IS_LL_ADC_REG_SEQ_SCAN_DISCONT_MODE(ADC_REG_InitStruct->SequencerDiscont));
assert_param(IS_LL_ADC_REG_CONTINUOUS_MODE(ADC_REG_InitStruct->ContinuousMode));
assert_param(IS_LL_ADC_REG_DMA_TRANSFER(ADC_REG_InitStruct->DMATransfer));
assert_param(IS_LL_ADC_REG_OVR_DATA_BEHAVIOR(ADC_REG_InitStruct->Overrun));
/* Note: Hardware constraint (refer to description of this function): */
/* ADC instance must be disabled. */
if(LL_ADC_IsEnabled(ADCx) == 0U)
{
/* Configuration of ADC hierarchical scope: */
/* - ADC group regular */
/* - Set ADC group regular trigger source */
/* - Set ADC group regular sequencer discontinuous mode */
/* - Set ADC group regular continuous mode */
/* - Set ADC group regular conversion data transfer: no transfer or */
/* transfer by DMA, and DMA requests mode */
/* - Set ADC group regular overrun behavior */
/* Note: On this STM32 serie, ADC trigger edge is set to value 0x0 by */
/* setting of trigger source to SW start. */
MODIFY_REG(ADCx->CFGR1,
ADC_CFGR1_EXTSEL
| ADC_CFGR1_EXTEN
| ADC_CFGR1_DISCEN
| ADC_CFGR1_CONT
| ADC_CFGR1_DMAEN
| ADC_CFGR1_DMACFG
| ADC_CFGR1_OVRMOD
,
ADC_REG_InitStruct->TriggerSource
| ADC_REG_InitStruct->SequencerDiscont
| ADC_REG_InitStruct->ContinuousMode
| ADC_REG_InitStruct->DMATransfer
| ADC_REG_InitStruct->Overrun
);
}
else
{
/* Initialization error: ADC instance is not disabled. */
status = ERROR;
}
return status;
}
/**
* @brief Initialize some features of ADC group regular.
* @note These parameters have an impact on ADC scope: ADC group regular.
* Refer to corresponding unitary functions into
* @ref ADC_LL_EF_Configuration_ADC_Group_Regular
* (functions with prefix "REG").
* @note The setting of these parameters by function @ref LL_ADC_Init()
* is conditioned to ADC state:
* ADC instance must be disabled.
* This condition is applied to all ADC features, for efficiency
* and compatibility over all STM32 families. However, the different
* features can be set under different ADC state conditions
* (setting possible with ADC enabled without conversion on going,
* ADC enabled with conversion on going, ...)
* Each feature can be updated afterwards with a unitary function
* and potentially with ADC in a different state than disabled,
* refer to description of each function for setting
* conditioned to ADC state.
* @note After using this function, other features must be configured
* using LL unitary functions.
* The minimum configuration remaining to be done is:
* - Set ADC group regular or group injected sequencer:
* map channel on the selected sequencer rank.
* Refer to function @ref LL_ADC_REG_SetSequencerRanks().
* - Set ADC channel sampling time
* Refer to function LL_ADC_SetChannelSamplingTime();
* @param ADCx ADC instance
* @param ADC_REG_InitStruct Pointer to a @ref LL_ADC_REG_InitTypeDef structure
* @retval An ErrorStatus enumeration value:
* - SUCCESS: ADC registers are initialized
* - ERROR: ADC registers are not initialized
*/
ErrorStatus LL_ADC_REG_Init(ADC_TypeDef *ADCx, LL_ADC_REG_InitTypeDef *ADC_REG_InitStruct)
{
ErrorStatus status = SUCCESS;
/* Check the parameters */
assert_param(IS_ADC_ALL_INSTANCE(ADCx));
#if defined(ADC3)
assert_param(IS_LL_ADC_REG_TRIG_SOURCE(ADCx, ADC_REG_InitStruct->TriggerSource));
#else
assert_param(IS_LL_ADC_REG_TRIG_SOURCE(ADC_REG_InitStruct->TriggerSource));
#endif
assert_param(IS_LL_ADC_REG_SEQ_SCAN_LENGTH(ADC_REG_InitStruct->SequencerLength));
if(ADC_REG_InitStruct->SequencerLength != LL_ADC_REG_SEQ_SCAN_DISABLE)
{
assert_param(IS_LL_ADC_REG_SEQ_SCAN_DISCONT_MODE(ADC_REG_InitStruct->SequencerDiscont));
}
assert_param(IS_LL_ADC_REG_CONTINUOUS_MODE(ADC_REG_InitStruct->ContinuousMode));
assert_param(IS_LL_ADC_REG_DMA_TRANSFER(ADC_REG_InitStruct->DMATransfer));
/* Note: Hardware constraint (refer to description of this function): */
/* ADC instance must be disabled. */
if(LL_ADC_IsEnabled(ADCx) == 0U)
{
/* Configuration of ADC hierarchical scope: */
/* - ADC group regular */
/* - Set ADC group regular trigger source */
/* - Set ADC group regular sequencer length */
/* - Set ADC group regular sequencer discontinuous mode */
/* - Set ADC group regular continuous mode */
/* - Set ADC group regular conversion data transfer: no transfer or */
/* transfer by DMA, and DMA requests mode */
/* Note: On this STM32 serie, ADC trigger edge is set when starting */
/* ADC conversion. */
/* Refer to function @ref LL_ADC_REG_StartConversionExtTrig(). */
if(ADC_REG_InitStruct->SequencerLength != LL_ADC_REG_SEQ_SCAN_DISABLE)
{
MODIFY_REG(ADCx->CR1,
ADC_CR1_DISCEN
| ADC_CR1_DISCNUM
,
ADC_REG_InitStruct->SequencerLength
| ADC_REG_InitStruct->SequencerDiscont
);
}
else
{
MODIFY_REG(ADCx->CR1,
ADC_CR1_DISCEN
| ADC_CR1_DISCNUM
,
ADC_REG_InitStruct->SequencerLength
| LL_ADC_REG_SEQ_DISCONT_DISABLE
);
}
MODIFY_REG(ADCx->CR2,
ADC_CR2_EXTSEL
| ADC_CR2_CONT
| ADC_CR2_DMA
,
ADC_REG_InitStruct->TriggerSource
| ADC_REG_InitStruct->ContinuousMode
| ADC_REG_InitStruct->DMATransfer
);
/* Set ADC group regular sequencer length and scan direction */
/* Note: Hardware constraint (refer to description of this function): */
/* Note: If ADC instance feature scan mode is disabled */
/* (refer to ADC instance initialization structure */
/* parameter @ref SequencersScanMode */
/* or function @ref LL_ADC_SetSequencersScanMode() ), */
/* this parameter is discarded. */
LL_ADC_REG_SetSequencerLength(ADCx, ADC_REG_InitStruct->SequencerLength);
}
else
{
/* Initialization error: ADC instance is not disabled. */
status = ERROR;
}
return status;
}
