void InitAll(void)
{
RCC->APB2ENR |= RCC_APB2ENR_IOPBEN; //Clock port
GPIOB->CRL &= ~(GPIO_CRL_CNF0 | GPIO_CRL_CNF1);
GPIOB->CRL |= (GPIO_CRL_MODE0_0 | GPIO_CRL_MODE1_0);
InitRCC();
//Разрешаем прерывание если кварц плохо
init_bad_clock_inter();
delay_timer_ms_init();
lcd_init();
InitUSART(9600);
InitUSART2(9600);
usart_interrupt_init();
usart2_interrupt_init();
init_keyboard();
//timer2_init(10);
InitSim900Port();
InitBuz();
InitMenu();
Init_Slow_Timer();
}
int main()
{
int ledID = 0;
InitRCC();
InitVTimers();
STM_EVAL_LEDInit(LED4);
STM_EVAL_LEDInit(LED3);
STM_EVAL_LEDInit(LED5);
STM_EVAL_LEDInit(LED6);
// //ADC test
// InitTrimmer(TRIMMER_1);
// InitDAC(DAC_2, MIN_ANALOG_VALUE_12b);
//
// while(1)
// {
//
// trimmerValue = GetTrimmerValue(TRIMMER_1);
//
// SetAnalogOutput(DAC_2, trimmerValue * 4);
//
// dacValue = GetAnalogOutput(DAC_2);
//
// volts = 2.979 * ((float)dacValue / (float)MAX_ANALOG_VALUE_12b);
// }
SetVTimerValue(TIMER_1, 500);
ClearVTimer(TIMER_15);
ClearVTimer(TIMER_10);
ClearVTimer(TIMER_12);
while(1)
{
if(IsVTimerElapsed(TIMER_1) == ELAPSED)
{
STM_EVAL_LEDOff(LED3);
STM_EVAL_LEDOff(LED4);
STM_EVAL_LEDOff(LED5);
STM_EVAL_LEDOff(LED6);
STM_EVAL_LEDOn(ledID);
if(ledID == 3)
{
ledID = 0;
}
else
{
ledID = ledID + 1;
}
SetVTimerValue(TIMER_1, 500);
}
VTimerTask();
}
}
int main()
{
InitRCC();
InitVTimers();
InitControllerPeripheral();
SetInitialConditions();
InitLCD();
while(1)
{
ControllerDisplayDataTask();
}
return 0;
}
int main(void)
{
float tempf;
InitRCC();
InitGPIO();
InitADC();
I2CInit();
InitIT();
Delay_Init(24);
// reset pot value
PotWrite(0x00);
while(1) {
if (mode == MODE_CAL) {
LED_GREEN_ON();
LED_RED_OFF();
uint16_t av = ADC_GetConversionValue(AN_ADCx);
if (av > trig_level) {
trig_level = av;
tempf = GetADCVolt(trig_level)*VOLT_DIV; // get voltage from piezo
tempf = GetTargetK(tempf); // get target amp coefficient
tempf = GetTargetR(tempf); // get R2 for opamp feedback
tempf = GetPotR(tempf); // get target resistance for pot as part of R2
PotWrite(GetWStep(tempf)); // write step to pot
}
} else {
// turn on red for working mode indication, turn green if mcu gets opamp output high
LED_RED_ON();
if (GPIO_ReadInputDataBit(OP_PORT, OP_PIN) == SET) {
LED_GREEN_ON();
delay_ms(500);
} else {
LED_GREEN_OFF();
}
}
}
}
