//--------------------------------------------------------------
int main(void) {
GPIO_InitTypeDef GPIO_InitStructure;
/* Enable the GPIOs clocks */
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA | RCC_AHBPeriph_GPIOB | RCC_AHBPeriph_GPIOC| RCC_AHBPeriph_GPIOD| RCC_AHBPeriph_GPIOE| RCC_AHBPeriph_GPIOH, ENABLE);
// запускаем тактирование GPIO порта F
// RCC_APB1PeriphClockCmd(RCC_AHBENR_GPIOBEN, ENABLE);
// Устанавливаем пины PF6, PF7, PF8, PF9 как выходные
// использовать будем PF6 и PF7, но уж проинициализируем все четыре LED
// GPIO_InitStructure.GPIO_Pin = GPIO_Pin_3 | GPIO_Pin_4 | GPIO_Pin_5;
// // | GPIO_Pin_9;
// GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
// GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
// GPIO_Init(GPIOB, &GPIO_InitStructure);
Init_GPIOs ();
xTaskCreate( vTaskLED1, ( signed char * ) "LED1", configMINIMAL_STACK_SIZE, NULL, 2,
( xTaskHandle * ) NULL);
xTaskCreate( vTaskLED2, ( signed char * ) "LED2", configMINIMAL_STACK_SIZE, NULL, 2,
( xTaskHandle * ) NULL);
/* Start the scheduler. */
vTaskStartScheduler();
/* Will only get here if there was insufficient memory to create the idle
task. The idle task is created within vTaskStartScheduler(). */
for (;;)
;
}
int main(void) {
initPowerSubsystem();
/* Enable the GPIOs clocks */
//RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA | RCC_AHBPeriph_GPIOB | RCC_AHBPeriph_GPIOC| RCC_AHBPeriph_GPIOD| RCC_AHBPeriph_GPIOE| RCC_AHBPeriph_GPIOH, ENABLE);
Init_GPIOs();
//xTaskCreate(vTaskLED1, ( signed char * ) "LED1", configMINIMAL_STACK_SIZE, NULL, 1, ( xTaskHandle * ) NULL);
xTaskCreate(vTaskLED2, ( signed char * ) "LED2", configMINIMAL_STACK_SIZE, NULL, 1, ( xTaskHandle * ) NULL);
vTaskStartScheduler();
initHD44780();
//disableHD44780();
while (1) {
vTaskDelay(1000 / portTICK_RATE_MS);
}
}
int main(void)
{
bool StanbyWakeUp ;
float Current_STBY;
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32l1xx_md.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32l1xx.c file
*/
Int_CurrentSTBY = Current_Measurement();
/* Check if the StandBy flag is set */
if (PWR_GetFlagStatus(PWR_FLAG_SB) != RESET)
{
/* System resumed from STANDBY mode */
/* Clear StandBy flag */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR,ENABLE);
PWR_ClearFlag(PWR_FLAG_SB);
StanbyWakeUp = TRUE;
} else
{
StanbyWakeUp = FALSE;
}
PWR_PVDCmd(DISABLE);
RCC_Configuration();
PWR_VoltageScalingConfig(PWR_VoltageScaling_Range1);
/* Wait Until the Voltage Regulator is ready */
while (PWR_GetFlagStatus(PWR_FLAG_VOS) != RESET) ;
/* Init I/O ports */
Init_GPIOs ();
/* Initializes ADC */
ADC_Icc_Init();
enableInterrupts();
/* Warning ! in TSL Init the sysTick interrupt is setted to:
SysTick_Config(RCC_Clocks.HCLK_Frequency / 2000 ---> 500 µs*/
/* Init Touch Sensing configuration */
TSL_Init();
sMCKeyInfo[0].Setting.b.IMPLEMENTED = 1;
sMCKeyInfo[0].Setting.b.ENABLED = 1;
sMCKeyInfo[0].DxSGroup = 0x00;
/* Initializes the LCD glass */
LCD_GLASS_Init();
while (1)
{
switch( State )
{
case 0:
//LED3 off and LED4 off
blink = 0;
GPIOB_ODR_value = 0x00000000;
ptr_PORTB->GPIOx_ODR = GPIOB_ODR_value;
break;
case 1:
//LED3 on and LED4 off
blink = 0;
GPIOB_ODR_value = 0x00000080;
ptr_PORTB->GPIOx_ODR = GPIOB_ODR_value;
break;
case 2:
//LED3 off and LED4 on
blink = 0;
GPIOB_ODR_value = 0x00000040;
ptr_PORTB->GPIOx_ODR = GPIOB_ODR_value;
break;
case 3:
//LED3 and LED4 blink with 2 second period
blink = 1;
break;
}
if(blink == 1)
{
GPIOB_ODR_value = 0x000000C0;
ptr_PORTB->GPIOx_ODR = GPIOB_ODR_value;
Delay(100);
GPIOB_ODR_value = 0x00000000;
ptr_PORTB->GPIOx_ODR = GPIOB_ODR_value;
Delay(100);
}
}
return(0);
}
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32l1xx_md.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32l1xx.c file
*/
/* Configure Clocks for Application need */
RCC_Configuration();
/* Configure RTC Clocks */
RTC_Configuration();
/* Set internal voltage regulator to 1.8V */
PWR_VoltageScalingConfig(PWR_VoltageScaling_Range1);
/* Wait Until the Voltage Regulator is ready */
while (PWR_GetFlagStatus(PWR_FLAG_VOS) != RESET) ;
/* Enable debug features in low power modes (Sleep, STOP and STANDBY) */
#ifdef DEBUG_SWD_PIN
DBGMCU_Config(DBGMCU_SLEEP | DBGMCU_STOP | DBGMCU_STANDBY, ENABLE);
#endif
/* Configure SysTick IRQ and SysTick Timer to generate interrupts */
RCC_GetClocksFreq(&RCC_Clocks);
SysTick_Config(RCC_Clocks.HCLK_Frequency / 500);
/* Init I/O ports */
Init_GPIOs();
/* Initializes the LCD glass */
LCD_GLASS_Configure_GPIO();
LCD_GLASS_Init();
/* Display Welcome message */
LCD_GLASS_ScrollSentence(" ** TEMPERATURE SENSOR EXAMPLE ** ",1,SCROLL_SPEED);
/* Disable SysTick IRQ and SysTick Timer */
SysTick->CTRL &= ~ ( SysTick_CTRL_TICKINT_Msk | SysTick_CTRL_ENABLE_Msk );
/* Test user or factory temperature sensor calibration value */
if ( testFactoryCalibData() == SUCCESS ) getFactoryTSCalibData(&calibdata);
else if ( testUserCalibData() == SUCCESS ) calibdata = *USER_CALIB_DATA;
else {
/* User calibration or factory calibration TS data are not available */
calibdata.TS_CAL_1 = DEFAULT_COLD_VAL;
calibdata.TS_CAL_2 = DEFAULT_HOT_VAL;
writeCalibData(&calibdata);
calibdata = *USER_CALIB_DATA;
}
/* Configure Wakeup from sleep using RTC event*/
configureWakeup();
/* Configure direct memory access for ADC usage*/
configureDMA();
/* Configure ADC for temperature sensor value conversion */
configureADC_Temp();
while(1) {
/* Re-enable DMA and ADC conf and start Temperature Data acquisition */
acquireTemperatureData();
/* Stay in SLEEP mode untill the data are acquired by ADC */
__WFI();
/* for DEBUG purpose uncomment the following line and comment the __WFI call to do not enter STOP mode */
// while (!flag_ADCDMA_TransferComplete);
/* Disable ADC, DMA and clock*/
powerDownADC_Temper();
/* Process mesured Temperature data - calculate average temperature value in °C */
processTempData();
if (flag_UserButton == TRUE) {
clearUserButtonFlag();
if (CurrentlyDisplayed == Display_TemperatureDegC)
CurrentlyDisplayed = Display_ADCval;
else
CurrentlyDisplayed = Display_TemperatureDegC;
}
if (CurrentlyDisplayed == Display_TemperatureDegC) {
/* print average temperature value in °C */
sprintf(strDisp, "%d °C", temperature_C );
} else {
/* print result of ADC conversion */
sprintf(strDisp, "> %d", tempAVG );
}
LCD_GLASS_Clear();
LCD_GLASS_DisplayString( (unsigned char *) strDisp );
/* Enable RTC Wakeup */
RTC_WakeUpCmd(ENABLE);
/* Clear WakeUp flag */
PWR_ClearFlag(PWR_FLAG_WU);
/* Enter in wait for interrupt stop mode*/
PWR_EnterSTOPMode(PWR_Regulator_LowPower, PWR_STOPEntry_WFI);
RCC_Configuration(); // reinitialize clock
/* After Wake up : Disable Wake up from RTC*/
RTC_WakeUpCmd(DISABLE);
}
}
int main(void)
{
bool StanbyWakeUp ;
float Current_STBY;
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32l1xx_md.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32l1xx.c file
*/
Int_CurrentSTBY = Current_Measurement();
/* Check if the StandBy flag is set */
if (PWR_GetFlagStatus(PWR_FLAG_SB) != RESET)
{
/* System resumed from STANDBY mode */
/* Clear StandBy flag */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR,ENABLE);
PWR_ClearFlag(PWR_FLAG_SB);
StanbyWakeUp = TRUE;
} else
{
StanbyWakeUp = FALSE;
}
PWR_PVDCmd(DISABLE);
RCC_Configuration();
PWR_VoltageScalingConfig(PWR_VoltageScaling_Range1);
/* Wait Until the Voltage Regulator is ready */
while (PWR_GetFlagStatus(PWR_FLAG_VOS) != RESET) ;
/* Init I/O ports */
Init_GPIOs ();
/* Initializes ADC */
ADC_Icc_Init();
enableInterrupts();
/* Warning ! in TSL Init the sysTick interrupt is setted to:
SysTick_Config(RCC_Clocks.HCLK_Frequency / 2000 ---> 500 µs*/
/* Init Touch Sensing configuration */
TSL_Init();
sMCKeyInfo[0].Setting.b.IMPLEMENTED = 1;
sMCKeyInfo[0].Setting.b.ENABLED = 1;
sMCKeyInfo[0].DxSGroup = 0x00;
/* Initializes the LCD glass */
LCD_GLASS_Init();
// EECE 337 Code -- Start
int N;
int f;
char str[8];
N = 10;
// Call to original factorial algorithm in C - for debugging
//f = factorial_orig( N );
factorial(&f, N);
// Copy result to f
sprintf (str, "%X", f);
//printf( "factorial of %i is %i\n", N, f);
LCD_GLASS_DisplayString(str);
// EECE 337 Code -- End
return(0);
}
int main(void)
{
bool StanbyWakeUp ;
float Current_STBY;
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32l1xx_md.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32l1xx.c file
*/
Int_CurrentSTBY = Current_Measurement();
/* Check if the StandBy flag is set */
if (PWR_GetFlagStatus(PWR_FLAG_SB) != RESET)
{
/* System resumed from STANDBY mode */
/* Clear StandBy flag */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR,ENABLE);
PWR_ClearFlag(PWR_FLAG_SB);
StanbyWakeUp = TRUE;
} else
{
StanbyWakeUp = FALSE;
}
PWR_PVDCmd(DISABLE);
RCC_Configuration();
PWR_VoltageScalingConfig(PWR_VoltageScaling_Range1);
/* Wait Until the Voltage Regulator is ready */
while (PWR_GetFlagStatus(PWR_FLAG_VOS) != RESET) ;
/* Init I/O ports */
Init_GPIOs ();
/* Initializes ADC */
ADC_Icc_Init();
enableInterrupts();
/* Warning ! in TSL Init the sysTick interrupt is setted to:
SysTick_Config(RCC_Clocks.HCLK_Frequency / 2000 ---> 500 µs*/
/* Init Touch Sensing configuration */
TSL_Init();
sMCKeyInfo[0].Setting.b.IMPLEMENTED = 1;
sMCKeyInfo[0].Setting.b.ENABLED = 1;
sMCKeyInfo[0].DxSGroup = 0x00;
/* Initializes the LCD glass */
LCD_GLASS_Init();
// EECE 337 Code -- Start
char str[50]; // Used to display results
unsigned int delay_time = 5000; // Will delay for 5 seconds
const unsigned int numItems = 10; // # items in array
int MyArray[10] = { 365, 245, -499, 0, 23, 8, 200, -4, -50, 25 };
int minimum = 0; // Will hold minimum value
int maximum = 0; // Will hold maximum value
// Call Function to obtain Min and Max values from array
min_max(MyArray, numItems, &minimum, &maximum);
// Copy min result to str
sprintf (str, "%d", minimum);
// Display on LCD
LCD_GLASS_DisplayString(str);
// Pause for 5 seconds
Delay(delay_time);
// Clear LCD
LCD_GLASS_Clear();
// Copy max result to str
sprintf (str, "%d", maximum);
// Display on LCD
LCD_GLASS_DisplayString(str);
// Pause for 5 seconds
Delay(delay_time);
// EECE 337 Code -- End
return(0);
}
