/**************************************************************************************************
* @fn macRadioTurnOnPower
*
* @brief Logic and sequence for powering up the radio.
*
* @param none
*
* @return none
**************************************************************************************************
*/
MAC_INTERNAL_API void macRadioTurnOnPower(void)
{
/* Enable RF error trap */
MAC_MCU_RFERR_ENABLE_INTERRUPT();
#if defined MAC_RUNTIME_CC2591 || defined MAC_RUNTIME_CC2590
/* table ID is referenced only when runtime configuratino is enabled */
if (macRadioDefsRefTableId & 0xf0)
#endif /* defined MAC_RUNTIME_CC2591 || defined MAC_RUNTIME_CC2590 */
#if defined MAC_RUNTIME_CC2591 || defined MAC_RUNTIME_CC2590 || \
defined HAL_PA_LNA || defined HAL_PA_LNA_CC2590
{ /* either if compound statement or non-conditional compound statement */
/* (Re-)Configure PA and LNA control signals to RF frontend chips.
* Note that The register values are not retained during sleep.
*/
/* P1_1 -> PAEN */
//RFC_OBS_CTRL0 = RFC_OBS_CTRL_PA_PD_INV;
//OBSSEL1 = OBSSEL_OBS_CTRL0;
/* P1_4 -> EN (LNA control) */
//RFC_OBS_CTRL1 = RFC_OBS_CTRL_LNAMIX_PD_INV;
//OBSSEL4 = OBSSEL_OBS_CTRL1;
/* P1_5 -> PAEN */
RFC_OBS_CTRL0 = RFC_OBS_CTRL_PA_PD_INV;
OBSSEL5 = OBSSEL_OBS_CTRL0;
P1SEL &= ~0X10;
P1DIR |= 0X10;
P1_4 = 1; //P1_4 RXEN andy pa
/* For any RX, change CCA settings for CC2591 compression workaround.
* This will override LNA control if CC2591_COMPRESSION_WORKAROUND
* flag is defined.
*/
COMPRESSION_WORKAROUND_ON();
}
#endif /* defined MAC_RUNTIME_CC2591 || ... || defined HAL_PA_LNA_CC2590 */
if (macChipVersion <= REV_B)
{
/* radio initializations for disappearing RAM; PG1.0 and before only */
MAC_RADIO_SET_PAN_ID(macPib.panId);
MAC_RADIO_SET_SHORT_ADDR(macPib.shortAddress);
MAC_RADIO_SET_IEEE_ADDR(macPib.extendedAddress.addr.extAddr);
}
/* Turn on frame filtering */
MAC_RADIO_TURN_ON_RX_FRAME_FILTERING();
}
/**************************************************************************************************
* @fn macRxPromiscuousMode
*
* @brief Sets promiscuous mode - enabling or disabling it.
*
* @param none
*
* @return none
**************************************************************************************************
*/
MAC_INTERNAL_API void macRxPromiscuousMode(uint8 mode)
{
rxPromiscuousMode = mode;
if (rxPromiscuousMode == MAC_PROMISCUOUS_MODE_OFF)
{
MAC_RADIO_TURN_ON_RX_FRAME_FILTERING();
}
else
{
MAC_ASSERT((mode == MAC_PROMISCUOUS_MODE_WITH_BAD_CRC) ||
(mode == MAC_PROMISCUOUS_MODE_COMPLIANT)); /* invalid mode */
MAC_RADIO_TURN_OFF_RX_FRAME_FILTERING();
}
}
/*********************************************************************
* @fn MAC_SrcMatchEnable
*
* @brief Enabled AUTOPEND and source address matching. If number of source
* address table entries asked for is more than the hardware
* supports. It will allocate maximum number of entries and return
* MAC_INVALID_PARAMETER. This function shall be not be called from
* ISR. It is not thread safe.
*
* @param None
*
* @return None
*/
void MAC_SrcMatchEnable (void)
{
/* Turn on Frame Filter (TIMAC enables frame filter by default), TBD */
MAC_RADIO_TURN_ON_RX_FRAME_FILTERING();
/* Turn on Auto ACK (TIMAC turn on Auto ACK by default), TBD */
MAC_RADIO_TURN_ON_AUTO_ACK();
/* Turn on Autopend: set SRCMATCH.AUTOPEND and SRCMATCH.SRC_MATCH_EN */
MAC_RADIO_TURN_ON_SRC_MATCH();
/* Set SRCMATCH.AUTOPEND */
MAC_RADIO_TURN_ON_AUTOPEND();
/* Configure all the globals */
macSrcMatchIsEnabled = TRUE;
}
/*********************************************************************
* @fn MAC_SrcMatchEnable
*
* @brief Enabled AUTOPEND and source address matching. If number of source
* address table entries asked for is more than the hardware
* supports. It will allocate maximum number of entries and return
* MAC_INVALID_PARAMETER. This function shall be not be called from
* ISR. It is not thread safe.
*
* @param addressType - address type that the application uses
* SADDR_MODE_SHORT or SADDR_MODE_EXT
* @param num - number of source address table entries to be used
*
* @return MAC_SUCCESS or MAC_INVALID_PARAMETER
*/
uint8 MAC_SrcMatchEnable ( uint8 addrType, uint8 num )
{
uint8 rtn;
uint8 maxNum;
/* Verify the address type */
if( addrType != SADDR_MODE_SHORT && addrType != SADDR_MODE_EXT )
{
return MAC_INVALID_PARAMETER;
}
maxNum = ( addrType == SADDR_MODE_SHORT ) ?
MAC_SRCMATCH_SHORT_MAX_NUM_ENTRIES : MAC_SRCMATCH_EXT_MAX_NUM_ENTRIES;
if( num > maxNum )
{
rtn = MAC_INVALID_PARAMETER;
num = maxNum;
}
else
{
rtn = MAC_SUCCESS;
}
/* Turn on Frame Filter (TIMAC enables frame filter by default), TBD */
MAC_RADIO_TURN_ON_RX_FRAME_FILTERING();
/* Turn on Auto ACK (TIMAC turn on Auto ACK by default), TBD */
MAC_RADIO_TURN_ON_AUTO_ACK();
/* Turn on Autopend: set SRCMATCH.AUTOPEND and SRCMATCH.SRC_MATCH_EN */
MAC_RADIO_TURN_ON_SRC_MATCH();
/* Set SRCMATCH.AUTOPEND */
MAC_RADIO_TURN_ON_AUTOPEND();
/* Configure all the globals */
macSrcMatchIsEnabled = TRUE;
macSrcMatchMaxNumEntries = num;
macSrcMatchAddrMode = addrType;
return rtn;
}
/**************************************************************************************************
* @fn macRadioTurnOnPower
*
* @brief Logic and sequence for powering up the radio.
*
* @param none
*
* @return none
**************************************************************************************************
*/
MAC_INTERNAL_API void macRadioTurnOnPower(void)
{
/* Enable RF error trap */
MAC_MCU_RFERR_ENABLE_INTERRUPT();
#if defined MAC_RUNTIME_CC2591 || defined MAC_RUNTIME_CC2590 || \
defined MAC_RUNTIME_CC2592
/* table ID is referenced only when runtime configuratino is enabled */
if (macRadioDefsRefTableId & 0xf0)
#endif /* defined MAC_RUNTIME_CC2591 || defined MAC_RUNTIME_CC2590 */
#if defined MAC_RUNTIME_CC2591 || defined MAC_RUNTIME_CC2590 || \
defined MAC_RUNTIME_CC2592 || defined HAL_PA_LNA || \
defined HAL_PA_LNA_CC2590 || defined HAL_PA_LNA_CC2592
{ /* either if compound statement or non-conditional compound statement */
/* (Re-)Configure PA and LNA control signals to RF frontend chips.
* Note that The register values are not retained during sleep.
*/
/* PC3 -> PAEN */
RFC_OBS_CTRL0 = RFC_OBS_CTRL_PA_PD_INV;
OBSSEL3 = OBSSEL_OBS_CTRL0;
/* PC2 -> EN (LNA control) */
RFC_OBS_CTRL1 = RFC_OBS_CTRL_LNAMIX_PD_INV;
OBSSEL2 = OBSSEL_OBS_CTRL1;
}
#endif /* defined MAC_RUNTIME_CC2591 || ... || defined HAL_PA_LNA_CC2592 */
if (macChipVersion <= REV_B)
{
/* radio initializations for disappearing RAM; PG1.0 and before only */
MAC_RADIO_SET_PAN_ID(macPib.panId);
MAC_RADIO_SET_SHORT_ADDR(macPib.shortAddress);
MAC_RADIO_SET_IEEE_ADDR(macPib.extendedAddress.addr.extAddr);
}
/* Turn on frame filtering */
MAC_RADIO_TURN_ON_RX_FRAME_FILTERING();
}
/*********************************************************************
* @fn MAC_SrcMatchEnable
*
* @brief Enabled AUTOPEND and source address matching. If number of source
* address table entries asked for is more than the hardware
* supports. It will allocate maximum number of entries and return
* MAC_INVALID_PARAMETER. This function shall be not be called from
* ISR. It is not thread safe.
*
* @param None
*
* @return None
*/
void MAC_SrcMatchEnable (void)
{
/* Turn on Frame Filter (TIMAC enables frame filter by default), TBD */
MAC_RADIO_TURN_ON_RX_FRAME_FILTERING();
/* Turn on Auto ACK (TIMAC turn on Auto ACK by default), TBD */
MAC_RADIO_TURN_ON_AUTO_ACK();
/* Turn on Autopend: set SRCMATCH.AUTOPEND and SRCMATCH.SRC_MATCH_EN */
MAC_RADIO_TURN_ON_SRC_MATCH();
/* Set SRCMATCH.AUTOPEND */
MAC_RADIO_TURN_ON_AUTOPEND();
/* AUTOPEND function requires that the received
* frame is a DATA REQUEST MAC command frame
*/
MAC_RADIO_TURN_ON_AUTOPEND_DATAREQ_ONLY();
/* Configure all the globals */
macSrcMatchIsEnabled = TRUE;
}
/**************************************************************************************************
* @fn macRadioTurnOnPower
*
* @brief Logic and sequence for powering up the radio.
*
* @param none
*
* @return none
**************************************************************************************************
*/
MAC_INTERNAL_API void macRadioTurnOnPower(void)
{
/* Enable RF error trap */
MAC_MCU_RFERR_ENABLE_INTERRUPT();
#if defined MAC_RUNTIME_CC2591 || defined MAC_RUNTIME_CC2590 || \
defined MAC_RUNTIME_SE2431L || defined MAC_RUNTIME_CC2592
/* table ID is referenced only when runtime configuration is enabled */
if (macRadioDefsRefTableId & 0xf0)
#endif /* defined MAC_RUNTIME_CC2591 || defined MAC_RUNTIME_CC2590 */
#if defined MAC_RUNTIME_CC2591 || defined MAC_RUNTIME_CC2590 || \
defined MAC_RUNTIME_SE2431L || defined MAC_RUNTIME_CC2592 || \
defined HAL_PA_LNA || defined HAL_PA_LNA_CC2590 || \
defined HAL_PA_LNA_SE2431L || defined HAL_PA_LNA_CC2592
{ /* either if compound statement or non-conditional compound statement */
/* (Re-)Configure PA and LNA control signals to RF frontend chips.
* Note that The register values are not retained during sleep.
*/
if (paLnaChip == PA_LNA_SE2431L)
{
/* CPS or P0_7 maps closely to the HGM line */
HAL_PA_LNA_RX_HGM();
/* EN or CSD line is controlled via software so setting it high here to start the SE2431L frontend */
HAL_PA_LNA_RX_CSD_HIGH();
/* CTX or P1_1 maps closely to PAEN */
RFC_OBS_CTRL0 = RFC_OBS_CTRL_PA_PD_INV;
OBSSEL1 = OBSSEL_OBS_CTRL0;
}
else if(paLnaChip == PA_LNA_CC2592)
{
/* P1_1 -> PAEN */
RFC_OBS_CTRL0 = RFC_OBS_CTRL_PA_PD_INV;
OBSSEL1 = OBSSEL_OBS_CTRL0;
/* P1_0 -> EN (LNA control) */
RFC_OBS_CTRL1 = RFC_OBS_CTRL_LNAMIX_PD_INV;
OBSSEL0 = OBSSEL_OBS_CTRL1;
}
else
{
/* P1_1 -> PAEN */
RFC_OBS_CTRL0 = RFC_OBS_CTRL_PA_PD_INV;
OBSSEL1 = OBSSEL_OBS_CTRL0;
/* P1_4 -> EN (LNA control) */
RFC_OBS_CTRL1 = RFC_OBS_CTRL_LNAMIX_PD_INV;
OBSSEL4 = OBSSEL_OBS_CTRL1;
}
/* For any RX, change CCA settings for CC2591 compression workaround.
* This will override LNA control if CC2591_COMPRESSION_WORKAROUND
* flag is defined.
*/
}
#endif /* defined MAC_RUNTIME_CC2591 || ... || defined HAL_PA_LNA_SE2431L... */
if (macChipVersion <= REV_B)
{
/* radio initializations for disappearing RAM; PG1.0 and before only */
MAC_RADIO_SET_PAN_ID(macPib.panId);
MAC_RADIO_SET_SHORT_ADDR(macPib.shortAddress);
MAC_RADIO_SET_IEEE_ADDR(macPib.extendedAddress.addr.extAddr);
}
/* Turn on frame filtering */
MAC_RADIO_TURN_ON_RX_FRAME_FILTERING();
}
