void timer_init()
{
uint32_t val = 0;
/* Ensure timer is not running */
MEC1322_TMR32_CTL(0) &= ~(1 << 5);
/* Enable timer */
MEC1322_TMR32_CTL(0) |= (1 << 0);
val = MEC1322_TMR32_CTL(0);
/* Pre-scale = 48 -> 1MHz -> Period = 1us */
val = (val & 0xffff) | (47 << 16);
MEC1322_TMR32_CTL(0) = val;
/* Set preload to use the full 32 bits of the timer */
MEC1322_TMR32_PRE(0) = 0xffffffff;
/* Override the count */
MEC1322_TMR32_CNT(0) = 0xffffffff;
/* Auto restart */
MEC1322_TMR32_CTL(0) |= (1 << 3);
/* Start counting in timer 0 */
MEC1322_TMR32_CTL(0) |= (1 << 5);
}
void system_hibernate(uint32_t seconds, uint32_t microseconds)
{
int i;
#ifdef CONFIG_HOSTCMD_PD
/* Inform the PD MCU that we are going to hibernate. */
host_command_pd_request_hibernate();
/* Wait to ensure exchange with PD before hibernating. */
msleep(100);
#endif
cflush();
if (board_hibernate)
board_hibernate();
/* Disable interrupts */
interrupt_disable();
for (i = 0; i <= 92; ++i) {
task_disable_irq(i);
task_clear_pending_irq(i);
}
for (i = 8; i <= 23; ++i)
MEC1322_INT_DISABLE(i) = 0xffffffff;
MEC1322_INT_BLK_DIS |= 0xffff00;
/* Power down ADC VREF */
MEC1322_EC_ADC_VREF_PD |= 1;
/* Assert nSIO_RESET */
MEC1322_PCR_PWR_RST_CTL |= 1;
/* Disable UART */
MEC1322_UART_ACT &= ~0x1;
MEC1322_LPC_ACT &= ~0x1;
/* Disable JTAG */
MEC1322_EC_JTAG_EN &= ~1;
/* Disable 32KHz clock */
MEC1322_VBAT_CE &= ~0x2;
/* Stop watchdog */
MEC1322_WDG_CTL &= ~1;
/* Stop timers */
MEC1322_TMR32_CTL(0) &= ~1;
MEC1322_TMR32_CTL(1) &= ~1;
MEC1322_TMR16_CTL(0) &= ~1;
/* Power down ADC */
MEC1322_ADC_CTRL &= ~1;
/* Disable blocks */
MEC1322_PCR_CHIP_SLP_EN |= 0x3;
MEC1322_PCR_EC_SLP_EN |= MEC1322_PCR_EC_SLP_EN_SLEEP;
MEC1322_PCR_HOST_SLP_EN |= MEC1322_PCR_HOST_SLP_EN_SLEEP;
MEC1322_PCR_EC_SLP_EN2 |= MEC1322_PCR_EC_SLP_EN2_SLEEP;
MEC1322_PCR_SLOW_CLK_CTL &= 0xfffffc00;
/* Set sleep state */
MEC1322_PCR_SYS_SLP_CTL = (MEC1322_PCR_SYS_SLP_CTL & ~0x7) | 0x2;
CPU_SCB_SYSCTRL |= 0x4;
/* Setup GPIOs for hibernate */
if (board_hibernate_late)
board_hibernate_late();
#ifdef CONFIG_USB_PD_PORT_COUNT
/*
* Leave USB-C charging enabled in hibernate, in order to
* allow wake-on-plug. 5V enable must be pulled low.
*/
#if CONFIG_USB_PD_PORT_COUNT > 0
gpio_set_flags(GPIO_USB_C0_5V_EN, GPIO_PULL_DOWN | GPIO_INPUT);
gpio_set_level(GPIO_USB_C0_CHARGE_EN_L, 0);
#endif
#if CONFIG_USB_PD_PORT_COUNT > 1
gpio_set_flags(GPIO_USB_C1_5V_EN, GPIO_PULL_DOWN | GPIO_INPUT);
gpio_set_level(GPIO_USB_C1_CHARGE_EN_L, 0);
#endif
#endif /* CONFIG_USB_PD_PORT_COUNT */
if (hibernate_wake_pins_used > 0) {
for (i = 0; i < hibernate_wake_pins_used; ++i) {
const enum gpio_signal pin = hibernate_wake_pins[i];
gpio_reset(pin);
gpio_enable_interrupt(pin);
}
interrupt_enable();
task_enable_irq(MEC1322_IRQ_GIRQ8);
task_enable_irq(MEC1322_IRQ_GIRQ9);
task_enable_irq(MEC1322_IRQ_GIRQ10);
task_enable_irq(MEC1322_IRQ_GIRQ11);
task_enable_irq(MEC1322_IRQ_GIRQ20);
}
if (seconds || microseconds) {
MEC1322_INT_BLK_EN |= 1 << 17;
MEC1322_INT_ENABLE(17) |= 1 << 20;
interrupt_enable();
task_enable_irq(MEC1322_IRQ_HTIMER);
if (seconds > 2) {
ASSERT(seconds <= 0xffff / 8);
MEC1322_HTIMER_CONTROL = 1;
MEC1322_HTIMER_PRELOAD =
(seconds * 8 + microseconds / 125000);
} else {
MEC1322_HTIMER_CONTROL = 0;
MEC1322_HTIMER_PRELOAD =
(seconds * 1000000 + microseconds) * 2 / 71;
}
}
asm("wfi");
/* Use 48MHz clock to speed through wake-up */
MEC1322_PCR_PROC_CLK_CTL = 1;
/* Reboot */
_system_reset(0, 1);
/* We should never get here. */
while (1)
;
}
void system_hibernate(uint32_t seconds, uint32_t microseconds)
{
int i;
cflush();
/* Disable interrupts */
interrupt_disable();
for (i = 0; i <= 92; ++i) {
task_disable_irq(i);
task_clear_pending_irq(i);
}
for (i = 8; i <= 23; ++i)
MEC1322_INT_DISABLE(i) = 0xffffffff;
MEC1322_INT_BLK_DIS |= 0xffff00;
/* Set processor clock to lowest, 1MHz */
MEC1322_PCR_PROC_CLK_CTL = 48;
/* Power down ADC VREF */
MEC1322_EC_ADC_VREF_PD |= 1;
/* Assert nSIO_RESET */
MEC1322_PCR_PWR_RST_CTL |= 1;
/* Disable UART */
MEC1322_UART_ACT &= ~0x1;
MEC1322_LPC_ACT &= ~0x1;
/* Disable JTAG */
MEC1322_EC_JTAG_EN &= ~1;
/* Disable 32KHz clock */
MEC1322_VBAT_CE &= ~0x2;
/* Stop watchdog */
MEC1322_WDG_CTL &= ~1;
/* Stop timers */
MEC1322_TMR32_CTL(0) &= ~1;
MEC1322_TMR32_CTL(1) &= ~1;
MEC1322_TMR16_CTL(0) &= ~1;
/* Power down ADC */
MEC1322_ADC_CTRL &= ~1;
/* Disable blocks */
MEC1322_PCR_CHIP_SLP_EN |= 0x3;
MEC1322_PCR_EC_SLP_EN |= 0xe0700ff7;
MEC1322_PCR_HOST_SLP_EN |= 0x5f003;
MEC1322_PCR_EC_SLP_EN2 |= 0x1ffffff8;
MEC1322_PCR_SYS_SLP_CTL = (MEC1322_PCR_SYS_SLP_CTL & ~0x7) | 0x2;
MEC1322_PCR_SLOW_CLK_CTL &= 0xfffffc00;
CPU_SCB_SYSCTRL |= 0x4;
system_unpower_gpio();
#ifdef CONFIG_WAKE_PIN
gpio_set_flags_by_mask(gpio_list[CONFIG_WAKE_PIN].port,
gpio_list[CONFIG_WAKE_PIN].mask,
gpio_list[CONFIG_WAKE_PIN].flags);
gpio_enable_interrupt(CONFIG_WAKE_PIN);
interrupt_enable();
task_enable_irq(MEC1322_IRQ_GIRQ8);
task_enable_irq(MEC1322_IRQ_GIRQ9);
task_enable_irq(MEC1322_IRQ_GIRQ10);
task_enable_irq(MEC1322_IRQ_GIRQ11);
task_enable_irq(MEC1322_IRQ_GIRQ20);
#endif
if (seconds || microseconds) {
MEC1322_INT_BLK_EN |= 1 << 17;
MEC1322_INT_ENABLE(17) |= 1 << 20;
interrupt_enable();
task_enable_irq(MEC1322_IRQ_HTIMER);
if (seconds > 2) {
ASSERT(seconds <= 0xffff / 8);
MEC1322_HTIMER_CONTROL = 1;
MEC1322_HTIMER_PRELOAD =
(seconds * 8 + microseconds / 125000);
} else {
MEC1322_HTIMER_CONTROL = 0;
MEC1322_HTIMER_PRELOAD =
(seconds * 1000000 + microseconds) * 2 / 71;
}
}
asm("wfi");
/* We lost states of most modules, let's just reboot */
_system_reset(0, 1);
}
