/////////////////////////////////////////////////////////////////////////////
// Customized HardFault Handler which prints out debugging informations
/////////////////////////////////////////////////////////////////////////////
void HardFault_Handler_c(unsigned int * hardfault_args)
{
// from the book: "The definiteve guide to the ARM Cortex-M3"
volatile unsigned int stacked_r0;
volatile unsigned int stacked_r1;
volatile unsigned int stacked_r2;
volatile unsigned int stacked_r3;
volatile unsigned int stacked_r12;
volatile unsigned int stacked_lr;
volatile unsigned int stacked_pc;
volatile unsigned int stacked_psr;
stacked_r0 = ((unsigned long) hardfault_args[0]);
stacked_r1 = ((unsigned long) hardfault_args[1]);
stacked_r2 = ((unsigned long) hardfault_args[2]);
stacked_r3 = ((unsigned long) hardfault_args[3]);
stacked_r12 = ((unsigned long) hardfault_args[4]);
stacked_lr = ((unsigned long) hardfault_args[5]);
stacked_pc = ((unsigned long) hardfault_args[6]);
stacked_psr = ((unsigned long) hardfault_args[7]);
MIOS32_MIDI_SendDebugMessage("Hard Fault PC = %08x\n", stacked_pc); // ensure that at least the PC will be sent
MIOS32_MIDI_SendDebugMessage("==================\n");
MIOS32_MIDI_SendDebugMessage("!!! HARD FAULT !!!\n");
MIOS32_MIDI_SendDebugMessage("==================\n");
MIOS32_MIDI_SendDebugMessage("R0 = %08x\n", stacked_r0);
MIOS32_MIDI_SendDebugMessage("R1 = %08x\n", stacked_r1);
MIOS32_MIDI_SendDebugMessage("R2 = %08x\n", stacked_r2);
MIOS32_MIDI_SendDebugMessage("R3 = %08x\n", stacked_r3);
MIOS32_MIDI_SendDebugMessage("R12 = %08x\n", stacked_r12);
MIOS32_MIDI_SendDebugMessage("LR = %08x\n", stacked_lr);
MIOS32_MIDI_SendDebugMessage("PC = %08x\n", stacked_pc);
MIOS32_MIDI_SendDebugMessage("PSR = %08x\n", stacked_psr);
MIOS32_MIDI_SendDebugMessage("BFAR = %08x\n", (*((volatile unsigned long *)(0xE000ED38))));
MIOS32_MIDI_SendDebugMessage("CFSR = %08x\n", (*((volatile unsigned long *)(0xE000ED28))));
MIOS32_MIDI_SendDebugMessage("HFSR = %08x\n", (*((volatile unsigned long *)(0xE000ED2C))));
MIOS32_MIDI_SendDebugMessage("DFSR = %08x\n", (*((volatile unsigned long *)(0xE000ED30))));
MIOS32_MIDI_SendDebugMessage("AFSR = %08x\n", (*((volatile unsigned long *)(0xE000ED3C))));
#ifndef MIOS32_DONT_USE_LCD
// TODO: here we should select the normal font - but only if available!
// MIOS32_LCD_FontInit((u8 *)GLCD_FONT_NORMAL);
MIOS32_LCD_BColourSet(0xffffff);
MIOS32_LCD_FColourSet(0x000000);
MIOS32_LCD_DeviceSet(0);
MIOS32_LCD_Clear();
MIOS32_LCD_CursorSet(0, 0);
MIOS32_LCD_PrintString("!! HARD FAULT !!");
MIOS32_LCD_CursorSet(0, 1);
MIOS32_LCD_PrintFormattedString("at PC=0x%08x", stacked_pc);
#endif
_abort();
}
void vApplicationStackOverflowHook(xTaskHandle xTask, signed portCHAR *pcTaskName)
{
MIOS32_MIDI_SendDebugMessage("======================\n");
MIOS32_MIDI_SendDebugMessage("!!! STACK OVERFLOW !!!\n");
MIOS32_MIDI_SendDebugMessage("======================\n");
MIOS32_MIDI_SendDebugMessage("Function: %s\n", pcTaskName);
#ifndef MIOS32_DONT_USE_LCD
// TODO: here we should select the normal font - but only if available!
// MIOS32_LCD_FontInit((u8 *)GLCD_FONT_NORMAL);
MIOS32_LCD_BColourSet(0xffffff);
MIOS32_LCD_FColourSet(0x000000);
MIOS32_LCD_DeviceSet(0);
MIOS32_LCD_Clear();
MIOS32_LCD_CursorSet(0, 0);
MIOS32_LCD_PrintString("!! STACK OVERFLOW !!");
MIOS32_LCD_CursorSet(0, 1);
MIOS32_LCD_PrintFormattedString("in Task %s", pcTaskName);
#endif
_abort();
}
/////////////////////////////////////////////////////////////////////////////
// _exit() for newer newlib versions
/////////////////////////////////////////////////////////////////////////////
void exit(int par)
{
#ifndef MIOS32_DONT_USE_LCD
// TODO: here we should select the normal font - but only if available!
// MIOS32_LCD_FontInit((u8 *)GLCD_FONT_NORMAL);
MIOS32_LCD_BColourSet(0xffffff);
MIOS32_LCD_FColourSet(0x000000);
MIOS32_LCD_DeviceSet(0);
MIOS32_LCD_Clear();
MIOS32_LCD_CursorSet(0, 0);
MIOS32_LCD_PrintString("Goodbye!");
#endif
#ifndef MIOS32_DONT_USE_MIDI
// Note: message won't be sent if MIDI task cannot be created!
MIOS32_MIDI_SendDebugMessage("Goodbye!\n");
#endif
// pro forma: since this is a noreturn function, loop endless and call _abort (which will never exit)
while( 1 )
_abort();
}
/////////////////////////////////////////////////////////////////////////////
// enabled in FreeRTOSConfig.h
/////////////////////////////////////////////////////////////////////////////
void vApplicationMallocFailedHook(void)
{
#ifndef MIOS32_DONT_USE_LCD
// TODO: here we should select the normal font - but only if available!
// MIOS32_LCD_FontInit((u8 *)GLCD_FONT_NORMAL);
MIOS32_LCD_BColourSet(0xffffff);
MIOS32_LCD_FColourSet(0x000000);
MIOS32_LCD_DeviceSet(0);
MIOS32_LCD_Clear();
MIOS32_LCD_CursorSet(0, 0);
MIOS32_LCD_PrintString("FATAL: FreeRTOS "); // 16 chars
MIOS32_LCD_CursorSet(0, 1);
MIOS32_LCD_PrintString("Malloc Error!!! "); // 16 chars
#endif
#ifndef MIOS32_DONT_USE_MIDI
// Note: message won't be sent if MIDI task cannot be created!
MIOS32_MIDI_SendDebugMessage("FATAL: FreeRTOS Malloc Error!!!\n");
#endif
_abort();
}
/////////////////////////////////////////////////////////////////////////////
// Initializes application specific LCD driver
// IN: <mode>: optional configuration
// OUT: returns < 0 if initialisation failed
/////////////////////////////////////////////////////////////////////////////
s32 APP_LCD_Init(u32 mode)
{
GPIO_InitTypeDef GPIO_InitStructure;
s32 delay;
// set LCD type
mios32_lcd_parameters.lcd_type = MIOS32_LCD_TYPE_GLCD_CUSTOM;
// set initial font and colours
MIOS32_LCD_FontInit((u8 *)GLCD_FONT_NORMAL);
MIOS32_LCD_BColourSet(0xffffff);
MIOS32_LCD_FColourSet(0x000000);
// control lines
PIN_BL(1);
PIN_RS(1);
PIN_RD(1);
PIN_CS(1);
PIN_WR(1);
PIN_RST(1);
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_InitStructure.GPIO_Pin = APP_LCD_BL_PIN;
GPIO_Init(APP_LCD_BL_PORT, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = APP_LCD_RS_PIN;
GPIO_Init(APP_LCD_RS_PORT, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = APP_LCD_RD_PIN;
GPIO_Init(APP_LCD_RD_PORT, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = APP_LCD_WR_PIN;
GPIO_Init(APP_LCD_WR_PORT, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = APP_LCD_CS_PIN;
GPIO_Init(APP_LCD_CS_PORT, &GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = APP_LCD_RST_PIN;
GPIO_Init(APP_LCD_RST_PORT, &GPIO_InitStructure);
// Apply hardware reset
PIN_RST(0);
for(delay=0; delay<0x500; ++delay);
PIN_RST(1);
for(delay=0; delay<0x500; ++delay);
// configure data pins as outputs
GPIO_InitStructure.GPIO_Pin = APP_LCD_D_PINS;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
GPIO_Init(APP_LCD_D_PORT, &GPIO_InitStructure);
//----------- software reset ------------------------------------------------
APP_LCD_Cmd(ST7637_SWRESET);
//----------- disable autoread + Manual read once ---------------------------
APP_LCD_Cmd( ST7637_AUTOLOADSET ); // Auto Load Set 0xD7
APP_LCD_Data( 0xBF ); // Auto Load Disable
APP_LCD_Cmd( ST7637_EPCTIN ); // EE Read/write mode 0xE0
APP_LCD_Data( 0x00 ); // Set read mode
APP_LCD_Cmd( ST7637_EPMRD ); // Read active 0xE3
APP_LCD_Cmd( ST7637_EPCTOUT ); // Cancel control 0xE1
//---------------------------------- Sleep OUT ------------------------------
APP_LCD_Cmd( ST7637_DISPOFF ); // display off 0x28
APP_LCD_Cmd( ST7637_SLPOUT ); // Sleep Out 0x11
//--------------------------------Vop setting--------------------------------
APP_LCD_Cmd( ST7637_VOPSET ); // Set Vop by initial Module 0xC0
APP_LCD_Data( 0xFB ); // Vop = 13.64
APP_LCD_Data( 0x00 ); // base on Module
//----------------------------Set Register-----------------------------------
APP_LCD_Cmd( ST7637_BIASSEL ); // Bias select 0xC3
APP_LCD_Data( 0x00 ); // 1/12 Bias, base on Module
APP_LCD_Cmd( ST7637_BSTBMPXSEL ); // Setting Booster times 0xC4
APP_LCD_Data( 0x05 ); // Booster X 8
APP_LCD_Cmd( ST7637_BSTEFFSEL ); // Booster eff 0xC5
APP_LCD_Data( 0x11 ); // BE = 0x01 (Level 2)
APP_LCD_Cmd( ST7637_VGSORCSEL ); // Vg with booster x2 control 0xcb
APP_LCD_Data( 0x01 ); // Vg from Vdd2
APP_LCD_Cmd( ST7637_ID1SET ); // ID1 = 00 0xcc
APP_LCD_Data( 0x00 ); //
APP_LCD_Cmd( ST7637_ID3SET ); // ID3 = 00 0xce
APP_LCD_Data( 0x00 ); //
APP_LCD_Cmd( ST7637_COMSCANDIR ); // Glass direction
APP_LCD_Data( 0xC0 ); //
APP_LCD_Cmd( ST7637_ANASET ); // Analog circuit setting 0xd0
APP_LCD_Data( 0x1D ); //
APP_LCD_Cmd( ST7637_PTLMOD ); // PTL mode set
APP_LCD_Data( 0x18 ); // power normal mode
APP_LCD_Cmd( ST7637_INVOFF ); // Display Inversion OFF 0x20
APP_LCD_Cmd( ST7637_CASET ); // column range
APP_LCD_Data( 0x04 ); //
APP_LCD_Data( 0x83 ); //
APP_LCD_Cmd( ST7637_RASET ); // raw range
APP_LCD_Data( 0x04 ); //
APP_LCD_Data( 0x83 ); //
APP_LCD_Cmd( ST7637_COLMOD ); // Color mode = 65k 0x3A
APP_LCD_Data( 0x05 ); //
APP_LCD_Cmd( ST7637_MADCTR ); // Memory Access Control 0x36
APP_LCD_Data( V12_MADCTRVAL );
APP_LCD_Cmd( ST7637_DUTYSET ); // Duty = 132 duty 0xb0
APP_LCD_Data( 0x7F );
APP_LCD_Cmd( ST7637_DISPON ); // Display ON
APP_LCD_Cmd( ST7637_FRAMESET ); // Gamma
APP_LCD_Data( 0x00 ); //
APP_LCD_Data( 0x03 ); //
APP_LCD_Data( 0x05 ); //
APP_LCD_Data( 0x07 ); //
APP_LCD_Data( 0x09 ); //
APP_LCD_Data( 0x0B ); //
APP_LCD_Data( 0x0D ); //
APP_LCD_Data( 0x0F ); //
APP_LCD_Data( 0x11 ); //
APP_LCD_Data( 0x13 ); //
APP_LCD_Data( 0x15 ); //
APP_LCD_Data( 0x17 ); //
APP_LCD_Data( 0x19 ); //
APP_LCD_Data( 0x1B ); //
APP_LCD_Data( 0x1D ); //
APP_LCD_Data( 0x1F ); //
return 0; // no error
}
/////////////////////////////////////////////////////////////////////////////
// This task is running endless in background
/////////////////////////////////////////////////////////////////////////////
void APP_Background(void)
{
// print static screen
MIOS32_LCD_FontInit((u8 *)GLCD_FONT_NORMAL);
MIOS32_LCD_BColourSet(0x000000);
MIOS32_LCD_FColourSet(0xffffff);
// clear LCD
MIOS32_LCD_Clear();
// print text
MIOS32_LCD_CursorSet(3, 3);
MIOS32_LCD_PrintString("ST7637 LCD");
MIOS32_LCD_CursorSet(7, 5);
MIOS32_LCD_PrintString("powered by");
// endless loop: print animations
u8 mios_r = 0;
u8 mios_g = 0;
u8 mios_b = 0;
u8 dir = 1;
u8 knob_icon_ctr[4] = {0, 3, 6, 9}; // memo: 12 icons
u8 knob_icon_delay_ctr[4] = {0, 2, 4, 6};
const u8 knob_icon_x[4] = {0, 100, 0, 100}; // memo: icon width 28
const u8 knob_icon_y[4] = {0, 0, 104, 104}; // memo: icon height 24
u8 vmeter_icon_ctr[2] = {0, 5}; // memo: 28 icons (14 used)
u8 vmeter_icon_dir[2] = {1, 1};
u8 vmeter_icon_delay_ctr[2] = {1, 4};
const u8 vmeter_icon_x[2] = {0, 120}; // memo: icon width 8
const u8 vmeter_icon_y[2] = {48, 48}; // memo: icon height 32
u8 hmeter_icon_ctr[2] = {6, 11}; // memo: 28 icons (14 used)
u8 hmeter_icon_dir[2] = {1, 0};
u8 hmeter_icon_delay_ctr[2] = {4, 2};
const u8 hmeter_icon_x[2] = {50, 50}; // memo: icon width 28
const u8 hmeter_icon_y[2] = {0, 120}; // memo: icon height 8
while( 1 ) {
s32 i;
// toggle the state of all LEDs (allows to measure the execution speed with a scope)
MIOS32_BOARD_LED_Set(0xffffffff, ~MIOS32_BOARD_LED_Get());
// colour-cycle "MIOS32" up and down :-)
// ST7637 supports 5bit r, 6bit g and 5bit b
if( dir ) {
if( mios_r < 0x1f )
++mios_r;
else if( mios_g < 0x3f )
++mios_g;
else if( mios_b < 0x1f )
++mios_b;
else
dir = 0;
} else {
if( mios_r > 0x00 )
--mios_r;
else if( mios_g > 0x00 )
--mios_g;
else if( mios_b > 0x00 )
--mios_b;
else
dir = 1;
}
// set new colour
MIOS32_LCD_FColourSet((mios_r << 16) | (mios_g << 8) | mios_b);
// print "MIOS32"
MIOS32_LCD_FontInit((u8 *)GLCD_FONT_BIG);
MIOS32_LCD_GCursorSet(16, 52);
MIOS32_LCD_PrintString("MIOS32");
// icons with different colour
MIOS32_LCD_FColourSet(((dir?mios_r:~mios_r) << 16) |
(~mios_g << 8) |
(dir?mios_b:~mios_b));
// print turning Knob icons at all edges
MIOS32_LCD_FontInit((u8 *)GLCD_FONT_KNOB_ICONS); // memo: 12 icons, icon size: 28x24
for(i=0; i<4; ++i) {
if( ++knob_icon_delay_ctr[i] > 10 ) {
knob_icon_delay_ctr[i] = 0;
if( ++knob_icon_ctr[i] >= 12 )
knob_icon_ctr[i] = 0;
}
MIOS32_LCD_GCursorSet(knob_icon_x[i], knob_icon_y[i]);
MIOS32_LCD_PrintChar(knob_icon_ctr[i]);
}
// print vmeter icons
MIOS32_LCD_FontInit((u8 *)GLCD_FONT_METER_ICONS_V); // memo: 28 icons, 14 used, icon size: 8x32
for(i=0; i<2; ++i) {
if( ++vmeter_icon_delay_ctr[i] > 5 ) {
vmeter_icon_delay_ctr[i] = 0;
if( vmeter_icon_dir[i] ) {
if( ++vmeter_icon_ctr[i] >= 13 )
vmeter_icon_dir[i] = 0;
} else {
if( --vmeter_icon_ctr[i] < 1 )
vmeter_icon_dir[i] = 1;
}
}
MIOS32_LCD_GCursorSet(vmeter_icon_x[i], vmeter_icon_y[i]);
MIOS32_LCD_PrintChar(vmeter_icon_ctr[i]);
}
// print hmeter icons
MIOS32_LCD_FontInit((u8 *)GLCD_FONT_METER_ICONS_H); // memo: 28 icons, 14 used, icon size: 28x8
for(i=0; i<2; ++i) {
if( ++hmeter_icon_delay_ctr[i] > 7 ) {
hmeter_icon_delay_ctr[i] = 0;
if( hmeter_icon_dir[i] ) {
if( ++hmeter_icon_ctr[i] >= 13 )
hmeter_icon_dir[i] = 0;
} else {
if( --hmeter_icon_ctr[i] < 1 )
hmeter_icon_dir[i] = 1;
}
}
MIOS32_LCD_GCursorSet(hmeter_icon_x[i], hmeter_icon_y[i]);
MIOS32_LCD_PrintChar(hmeter_icon_ctr[i]);
}
}
}
