void Sys_Standby(void)
{
stop_flag=1;
// while(1)
// {
NVIC_SystemLPConfig(NVIC_LP_SLEEPDEEP,ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE); //使能PWR和BKP外设时钟
PWR_WakeUpPinCmd(ENABLE); //使能唤醒管脚功能
//PWR_EnterSTANDBYMode(); //进入待命（STANDBY）模式
PWR_EnterSTOPMode(PWR_Regulator_LowPower, PWR_STOPEntry_WFI); //在停机模式时，程序停在这个函数中
//PWR_EnterSTOPMode(PWR_Regulator_ON, PWR_STOPEntry_WFI); //在停机模式时，程序停在这个函数中
//WFI表示wait for interrupt,WFE表示wait for event
//如果发生中断唤醒，会先执行中断程序 ，再执行PWR_EnterSTOPMode的下1行代码
//重新初始化
SystemInit();
//SoftReset();
// if(Check_WKUP())
// break;
// if(longpress==0)
// break;
// }
//重新初始化
//SystemInit();
}
/**
* @brief Enters MCU in STANDBY mode. The wake-up from STANDBY mode is performed
* when a rising edge is detected on WakeUp pin.
* @param None
* @retval None
*/
void LowPower_EnterSTANDBYMode_WAKEUP_1(void)
{
// LCD_Clear(LCD_COLOR_WHITE);
/* Set the LCD Back Color */
// LCD_SetBackColor(LCD_COLOR_BLUE);
/* Set the LCD Text Color */
// LCD_SetTextColor(LCD_COLOR_WHITE);
// LCD_DisplayStringLine(LCD_LINE_7, " MCU in STANDBY Mode");
// LCD_DisplayStringLine(LCD_LINE_8, " To exit press SEL ");
/* Check if the StandBy flag is set */
if (PWR_GetFlagStatus(PWR_FLAG_SB) != RESET)
{
/* Clear StandBy flag */
PWR_ClearFlag(PWR_FLAG_SB);
RTC_WaitForSynchro();
}
RTC_AlarmCmd(RTC_Alarm_A, DISABLE);
/* Enable WakeUp pin */
PWR_WakeUpPinCmd(PWR_WakeUpPin_1, ENABLE);
/* Request to enter STANDBY mode (Wake Up flag is cleared in PWR_EnterSTANDBYMode function) */
PWR_EnterSTANDBYMode();
}
/**-----------------------------------------------------------------------------
* @brief Entree en mode Stop.
*/
void STOP_MODE() {
EXTI_InitTypeDef EXTI_InitStructure;
NVIC_InitTypeDef NVIC_InitStructure;
// Config IT
SYSCFG_EXTILineConfig(EXTI_PortSourceGPIOA, EXTI_PinSource0); // Connect EXTI Line0 to PA0 pin
// Configure EXTI Line0
EXTI_InitStructure.EXTI_Line = EXTI_Line0;
EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
EXTI_InitStructure.EXTI_LineCmd = ENABLE;
EXTI_Init(&EXTI_InitStructure);
// Enable and set EXTI Line0 Interrupt to the lowest priority
NVIC_InitStructure.NVIC_IRQChannel = EXTI0_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
// Config Mode Stop
PWR_WakeUpPinCmd(ENABLE);
PWR_BackupRegulatorCmd(DISABLE);
PWR_FlashPowerDownCmd(ENABLE);
/* Enable PWR and BKP clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
// Entree Mode Stop
PWR_EnterSTOPMode(PWR_Regulator_LowPower, PWR_STOPEntry_WFI);
}
/**
* @brief This function configures the system to enter Standby mode for
* current consumption measurement purpose.
* STANDBY Mode
* ============
* - IWDG and LSI OFF
* - Current Consumption ~0.3uA
* - Wakeup using WakeUp Pin 1 (PA.00)
* @param None
* @retval None
*/
void StandbyMode_Measure(void)
{
/* Configure Key Button*/
STM_EVAL_PBInit(BUTTON_KEY,BUTTON_MODE_GPIO);
/* Wait Until Key button pressed */
while(STM_EVAL_PBGetState(BUTTON_KEY) == RESET)
{
}
/* Wait Until Key button pressed */
while(STM_EVAL_PBGetState(BUTTON_KEY) != RESET)
{
}
/* Enable Ultra low power mode */
PWR_UltraLowPowerCmd(ENABLE);
/* Clear PWR WakeUp flag */
PWR_ClearFlag(PWR_FLAG_WU);
/* Enable WKUP pin 1 */
PWR_WakeUpPinCmd(PWR_WakeUpPin_1, ENABLE);
/* Request to enter STANDBY mode */
PWR_EnterSTANDBYMode();
/* Infinite loop */
while (1)
{
}
}
/*********************************************************************************************************
** Function name: enter_low_power_mode
** Descriptions: enter_low_power_mode
** input parameters: none
** output parameters: none
** Returned value: none
*********************************************************************************************************/
void enter_low_power_mode(POWER_MODE mode)
{
switch(mode)
{
case SLEEP:
PWR_EnterSLEEPMode(PWR_Regulator_ON,PWR_SLEEPEntry_WFI);
break;
case STOP:
PWR_EnterSTOPMode(PWR_Regulator_ON, PWR_STOPEntry_WFI);
break;
case LPSTOP:
PWR_EnterSTOPMode(PWR_Regulator_LowPower, PWR_STOPEntry_WFI);
break;
case STANDBY:
PWR_EnterSTANDBYMode();
PWR_WakeUpPinCmd(ENABLE);
break;
default:
break;
}
}
/************************************************
* 函 数: Standby_SysEnter(void)
* 功 能: 系统进入待机模式
*
* 参 数: 无
*
* 返回值: 无
*************************************************/
void Standby_SysEnter(void)
{
RCC_APB2PeriphResetCmd(0x01FC, DISABLE); // 复位所有IO口
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE); // 使能PWR外设时钟
PWR_WakeUpPinCmd(ENABLE); // 使能唤醒引脚唤醒功能
PWR_EnterSTANDBYMode(); // 进入待机模式
} // Standby_SysEnter()
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
files (startup_stm32f40_41xxx.s/startup_stm32f427_437xx.s/startup_stm32f429_439xx.s)
before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32f4xx.c file
*/
/* Initialize LEDs mounted on EVAL board */
STM_EVAL_LEDInit(LED1);
STM_EVAL_LEDInit(LED2);
/* Initialize Key Button mounted on EVAL board */
STM_EVAL_PBInit(BUTTON_KEY, BUTTON_MODE_EXTI);
/* RTC configuration */
RTC_Config();
/* Turn on LED1 */
STM_EVAL_LEDOn(LED1);
/* Enable WKUP pin */
PWR_WakeUpPinCmd(ENABLE);
/* Configure the SysTick to generate an interrupt each 250 ms */
SysTick_Configuration();
while (1)
{
}
}
void HAL_Core_Execute_Stop_Mode(void)
{
/* Enable WKUP pin */
PWR_WakeUpPinCmd(ENABLE);
/* Request to enter STOP mode with regulator in low power mode */
PWR_EnterSTOPMode(PWR_Regulator_LowPower, PWR_STOPEntry_WFI);
/* At this stage the system has resumed from STOP mode */
/* Enable HSE, PLL and select PLL as system clock source after wake-up from STOP */
/* Enable HSE */
RCC_HSEConfig(RCC_HSE_ON);
/* Wait till HSE is ready */
if(RCC_WaitForHSEStartUp() != SUCCESS)
{
/* If HSE startup fails try to recover by system reset */
NVIC_SystemReset();
}
/* Enable PLL */
RCC_PLLCmd(ENABLE);
/* Wait till PLL is ready */
while(RCC_GetFlagStatus(RCC_FLAG_PLLRDY) == RESET);
/* Select PLL as system clock source */
RCC_SYSCLKConfig(RCC_SYSCLKSource_PLLCLK);
/* Wait till PLL is used as system clock source */
while(RCC_GetSYSCLKSource() != 0x08);
}
void pwr_sw_init (void)
{
EXTI_InitTypeDef EXTI_InitStructure;
NVIC_InitTypeDef NVIC_InitStructure;
//Enable PA0 as WKUP Pin, this will Wake up Chip from Standby Mode on rising edge
//Configures pin as input with Pull-down resistor
PWR_WakeUpPinCmd(PWR_WakeUpPin_1, ENABLE);
//Enable interrupt on PA0 Pin
// Enable SYSCFG clock
RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);
// Connect EXTI0 Line to PA0 pin
SYSCFG_EXTILineConfig(EXTI_PortSourceGPIOA, EXTI_PinSource0);
// Configure EXTI0 line
EXTI_InitStructure.EXTI_Line = EXTI_Line0;
EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
EXTI_InitStructure.EXTI_LineCmd = ENABLE;
EXTI_Init(&EXTI_InitStructure);
// Enable and set EXTI0_1_IRQn Interrupt
NVIC_InitStructure.NVIC_IRQChannel = EXTI0_1_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPriority = 0x00;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
}
void Sys_Standby(void)
{
NVIC_SystemLPConfig(NVIC_LP_SLEEPDEEP,ENABLE);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE); //使能PWR和BKP外设时钟
PWR_WakeUpPinCmd(ENABLE); //使能唤醒管脚功能
PWR_EnterSTANDBYMode(); //进入待命（STANDBY）模式
}
void PWR_StandbyMode( void )
{
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR | RCC_APB1Periph_BKP, ENABLE);
PWR_WakeUpPinCmd(ENABLE);
PWR_BackupAccessCmd(ENABLE);
PWR_ClearFlag(PWR_FLAG_SB);
PWR_EnterSTANDBYMode();
}
/**
* @brief This function configures the system to enter Standby mode for
* current consumption measurement purpose.
* STANDBY Mode
* ============
* - RTC OFF
* - IWDG and LSI OFF
* - Wakeup using WakeUp Pin2 (PC.13)
* @param None
* @retval None
*/
void StandbyMode_Measure(void)
{
/* Disable wake-up source(Wake up pin) to guarantee free access to WUT level-OR input */
PWR_WakeUpPinCmd(PWR_WakeUpPin_2, DISABLE);
/* Clear Wake-up flag */
PWR_ClearFlag(PWR_FLAG_WU);
PWR_ClearFlag(PWR_FLAG_SB);
/* Enable WKUP pin 1 */
PWR_WakeUpPinCmd(PWR_WakeUpPin_2,ENABLE);
/* Request to enter STANDBY mode (Wake Up flag is cleared in PWR_EnterSTANDBYMode function) */
PWR_EnterSTANDBYMode();
/* Infinite loop */
while (1)
{
}
}
/*******************************************************************************
* Function Name : LowPower_Init
* Description : Initializes Low Power application.
* Input : None
* Output : None
* Return : None
*******************************************************************************/
void LowPower_Init(void)
{
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
/* Enable WakeUp pin */
PWR_WakeUpPinCmd(ENABLE);
/* Enable Clock Security System(CSS) */
RCC_ClockSecuritySystemCmd(ENABLE);
}
void HAL_Core_Execute_Standby_Mode(void)
{
/* Enable WKUP pin */
PWR_WakeUpPinCmd(ENABLE);
/* Request to enter STANDBY mode */
PWR_EnterSTANDBYMode();
/* Following code will not be reached */
while(1);
}
//进入待机模式
void StandbyMode(void)
{
//关闭不需要的外设
RCC_AHB1PeriphResetCmd(0X01FF,ENABLE); //复位所有 IO 口
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);//使能 PWR 时钟
PWR_ClearFlag(PWR_FLAG_WU);//清除 Wake-up 标志
PWR_WakeUpPinCmd(ENABLE);//设置 WKUP 用于唤醒
PWR_EnterSTANDBYMode();//进入待机模式
}
void StandBy(void)
{
PushREG(REGA,REG_Shut,0x00,0x00);
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
NVIC_SystemLPConfig(NVIC_LP_SEVONPEND,ENABLE);
PWR_WakeUpPinCmd(ENABLE);
PWR_ClearFlag(PWR_FLAG_WU);
PWR_ClearFlag(PWR_FLAG_SB);
PWR_EnterSTANDBYMode();
return;
}
/**
* @brief This function configures the system to enter Standby mode for
* current consumption measurement purpose.
* STANDBY Mode
* ============
* - Backup SRAM and RTC OFF
* - IWDG and LSI OFF
* - Wakeup using WakeUp Pin (PA.00)
* @param None
* @retval None
*/
void StandbyMode_Measure(void)
{
/* Enable WKUP pin 1 */
PWR_WakeUpPinCmd(ENABLE);
/* Request to enter STANDBY mode (Wake Up flag is cleared in PWR_EnterSTANDBYMode function) */
PWR_EnterSTANDBYMode();
/* Infinite loop */
while (1)
{
}
}
/**
* @brief Enters MCU in STANDBY mode. The wake-up from STANDBY mode is performed
* by an RTC Alarm event.
* @param None
* @retval None
*/
void LowPower_EnterSTANDBYMode_RTCAlarm(void)
{
// LCD_Clear(LCD_COLOR_WHITE);
/* Set the LCD Back Color */
// LCD_SetBackColor(LCD_COLOR_BLUE);
/* Set the LCD Text Color */
// LCD_SetTextColor(LCD_COLOR_WHITE);
/* External Interrupt Disable */
//Demo_IntExtOnOffCmd(DISABLE);
/* Enable WakeUp pin */
PWR_WakeUpPinCmd(PWR_WakeUpPin_1, ENABLE);
/* Check if the StandBy flag is set */
if (PWR_GetFlagStatus(PWR_FLAG_SB) != RESET)
{
/* Clear StandBy flag */
PWR_ClearFlag(PWR_FLAG_SB);
RTC_WaitForSynchro();
}
if (RTC_ReadBackupRegister(RTC_BKP_DR0) != 0x5AA5)
{
// LCD_DisplayStringLine(LCD_LINE_1, "Time and Date are ");
// LCD_DisplayStringLine(LCD_LINE_2, "not configured, ");
// LCD_DisplayStringLine(LCD_LINE_3, "please go to the ");
// LCD_DisplayStringLine(LCD_LINE_4, "calendar menu and ");
// LCD_DisplayStringLine(LCD_LINE_5, "set the time and ");
// LCD_DisplayStringLine(LCD_LINE_6, "date parameters. ");
// LCD_DisplayStringLine(LCD_LINE_7, "Press JoyStick to ");
// LCD_DisplayStringLine(LCD_LINE_8, "continue... ");
/* External Interrupt Enable */
//Demo_IntExtOnOffCmd(ENABLE);
return;
}
Calendar_AlarmPreAdjust_A();
// LCD_DisplayStringLine(LCD_LINE_7, " MCU in STANDBY Mode");
// LCD_DisplayStringLine(LCD_LINE_8, " Wait For RTC Alarm ");
/* Request to enter STANDBY mode (Wake Up flag is cleared in PWR_EnterSTANDBYMode function) */
PWR_EnterSTANDBYMode();
}
/**
* @brief This function configures the system to enter Standby mode for
* current consumption measurement purpose.
* STANDBY Mode
* ============
* - Backup SRAM and RTC OFF
* - IWDG and LSI OFF
* - Wakeup using WakeUp Pin (PA.00)
* @param None
* @retval None
*/
void StandbyMode_Measure(void)
{
/* Enable WKUP pin 1 */
PWR_WakeUpPinCmd(ENABLE);
/* Clear Power WakeUp (CWUF) pending flag */
PWR_ClearFlag(PWR_FLAG_WU);
/* Request to enter STANDBY mode (Wake Up flag is cleared in PWR_EnterSTANDBYMode function) */
PWR_EnterSTANDBYMode();
/* Infinite loop */
while (1)
{
}
}
/* Check whether goto standby
* If PA0==0, goto standby mode.
*
*/
static void check_gotostandby(void)
{
wakeUpIOInit();
if(GPIO_ReadInputDataBit(GPIOA, GPIO_Pin_0) == Bit_RESET) {
//enable interrupt
EXTI->IMR |= EXTI_Line0;
//stm32 enter standby mode
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR, ENABLE);
PWR_WakeUpPinCmd(ENABLE);
PWR_EnterSTANDBYMode();
while(1);
} else {
//enable_watchdog(5);
}
}
/**
* @brief Main program
* @param None
* @retval None
*/
int main(void)
{
NVIC_InitTypeDef NVIC_InitStructure;
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32f4xx.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32f4xx.c file
*/
/* Initialize LEDs and Key Button mounted on STM32F4-Discovery board */
STM_EVAL_LEDInit(LED4);
STM_EVAL_LEDInit(LED3);
/* Configure Button EXTI line */
EXTI_InitStructure.EXTI_Line = EXTI_Line1;
EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising_Falling;
EXTI_InitStructure.EXTI_LineCmd = ENABLE;
EXTI_Init(&EXTI_InitStructure);
/* Enable and set Button EXTI Interrupt to the lowest priority */
NVIC_InitStructure.NVIC_IRQChannel = EXTI1_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x0F;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x0F;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
/* RTC configuration */
RTC_Config();
/* Turn on LED4 */
STM_EVAL_LEDOn(LED4);
/* Enable WKUP pin */
PWR_WakeUpPinCmd(ENABLE);
/* Configure the SysTick to generate an interrupt each 250 ms */
SysTick_Configuration();
while (1)
{
}
}
void HAL_Core_Execute_Standby_Mode(void)
{
/* Should we execute System Standby mode */
if(BKP_ReadBackupRegister(BKP_DR9) == 0xA5A5)
{
/* Clear Standby mode system flag */
BKP_WriteBackupRegister(BKP_DR9, 0xFFFF);
/* Enable WKUP pin */
PWR_WakeUpPinCmd(ENABLE);
/* Request to enter STANDBY mode */
PWR_EnterSTANDBYMode();
/* Following code will not be reached */
while(1);
}
}
/**
* @brief This function configures the system to enter Standby mode for
* current consumption measurement purpose.
* STANDBY Mode
* ============
* - RTC OFF
* - IWDG and LSI OFF
* - Wakeup using WakeUp Pin1 (PA.00)
* @param None
* @retval None
*/
void StandbyMode_Measure(void)
{
/* Check if the StandBy flag is set */
if (PWR_GetFlagStatus(PWR_FLAG_SB) != RESET)
{
/* Clear StandBy flag */
PWR_ClearFlag(PWR_FLAG_SB);
}
/* Enable WKUP pin 1 */
PWR_WakeUpPinCmd(PWR_WakeUpPin_1,ENABLE);
/* Request to enter STANDBY mode (Wake Up flag is cleared in PWR_EnterSTANDBYMode function) */
PWR_EnterSTANDBYMode();
/* Infinite loop */
while (1)
{
}
}
void platform_mcu_enter_standby(uint32_t secondsToWakeup)
{
platform_rtc_time_t time;
uint32_t currentSecond;
RTC_AlarmTypeDef RTC_AlarmStructure;
PWR_WakeUpPinCmd(ENABLE);
if(secondsToWakeup == MICO_WAIT_FOREVER)
PWR_EnterSTANDBYMode();
platform_log("Wake up in %d seconds", secondsToWakeup);
platform_rtc_get_time(&time);
currentSecond = time.hr*3600 + time.min*60 + time.sec;
currentSecond += secondsToWakeup;
RTC_AlarmStructure.RTC_AlarmTime.RTC_H12 = RTC_HourFormat_24;
RTC_AlarmStructure.RTC_AlarmTime.RTC_Hours = currentSecond/3600%24;
RTC_AlarmStructure.RTC_AlarmTime.RTC_Minutes = currentSecond/60%60;
RTC_AlarmStructure.RTC_AlarmTime.RTC_Seconds = currentSecond%60;
RTC_AlarmStructure.RTC_AlarmDateWeekDay = 0x31;
RTC_AlarmStructure.RTC_AlarmDateWeekDaySel = RTC_AlarmDateWeekDaySel_Date;
RTC_AlarmStructure.RTC_AlarmMask = RTC_AlarmMask_DateWeekDay ;
RTC_AlarmCmd(RTC_Alarm_A, DISABLE);
/* Disable the Alarm A */
RTC_ITConfig(RTC_IT_ALRA, DISABLE);
/* Clear RTC Alarm Flag */
RTC_ClearFlag(RTC_FLAG_ALRAF);
RTC_SetAlarm(RTC_Format_BIN, RTC_Alarm_A, &RTC_AlarmStructure);
/* Enable RTC Alarm A Interrupt: this Interrupt will wake-up the system from
STANDBY mode (RTC Alarm IT not enabled in NVIC) */
RTC_ITConfig(RTC_IT_ALRA, ENABLE);
/* Enable the Alarm A */
RTC_AlarmCmd(RTC_Alarm_A, ENABLE);
PWR_EnterSTANDBYMode();
}
/**
* @brief Sets up User button to wake system from STOP mode
*
* This function configures the User button (PA0) as a digital
* input that triggers an interrupt, which may be used to wake the
* system from STOP mode.
*
* You must define an interrupt handler (EXTI0_IRQHandler) to handle
* this interrupt.
*/
void initWakeupPin() {
/* Copy in your initButton() function from the `interrupt-button'
project in lab 5. */
NVIC_InitTypeDef NVIC_InitStructure;
EXTI_InitTypeDef EXTI_InitStructure;
GPIO_InitTypeDef GPIO_InitStructure;
// Enable GPIOA clock for User button peripheral on GPIOA
RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOA, ENABLE);
// Enable SYSCFG clock for interrupts
RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);
// Configure PA0 pin as input
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_DOWN;
GPIO_Init(GPIOA, &GPIO_InitStructure);
// Connect EXTI Line0 (external interrupt line 0) to PA0 pin
// This is the library function equivalent of running
// SYSCFG->EXTICR[0] &= SYSCFG_EXTICR1_EXTI0_PA;
SYSCFG_EXTILineConfig(EXTI_PortSourceGPIOA, EXTI_PinSource0);
// Configure the interrupt using library functions
EXTI_InitStructure.EXTI_Line = EXTI_Line0;
EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising_Falling;
EXTI_InitStructure.EXTI_LineCmd = ENABLE;
EXTI_Init(&EXTI_InitStructure);
// Enable and set priorities for the EXTI0 interrupt in NVIC
NVIC_InitStructure.NVIC_IRQChannel = EXTI0_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x01;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x01;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
PWR_WakeUpPinCmd(ENABLE);
}
int get_reset_reason( void )
{
int sts = 0;
if( RCC_GetFlagStatus( RCC_FLAG_PINRST ) == SET )
{
sts |= MAIN_RST_FOR_PIN;
}
if( RCC_GetFlagStatus( RCC_FLAG_PORRST ) == SET )
{
sts |= MAIN_RST_FOR_POR;
}
if( RCC_GetFlagStatus( RCC_FLAG_SFTRST ) == SET )
{
sts |= MAIN_RST_FOR_SFT;
}
if( RCC_GetFlagStatus( RCC_FLAG_IWDGRST ) == SET )
{
sts |= MAIN_RST_FOR_IWD;
if( main_is_enter_stby_mode == MAIN_ENTER_STBY_MODE )
{
main_is_enter_stby_mode = 0;
PWR_WakeUpPinCmd( ENABLE );
PWR_EnterSTANDBYMode();
}
}
if( RCC_GetFlagStatus( RCC_FLAG_WWDGRST ) == SET )
{
sts |= MAIN_RST_FOR_WWD;
}
if( RCC_GetFlagStatus( RCC_FLAG_LPWRRST ) == SET )
{
sts |= MAIN_RST_FOR_LPR;
}
RCC_ClearFlag(); // clear all reset flags
return sts;
} // end of get_reset_reason()
/**
* @brief Main program.
* @param None
* @retval None
*/
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32f10x_xx.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32f10x.c file
*/
/* Initialize LEDs and Key Button mounted on STM3210X-EVAL board */
STM_EVAL_LEDInit(LED1);
STM_EVAL_LEDInit(LED2);
STM_EVAL_PBInit(BUTTON_KEY, BUTTON_MODE_EXTI);
/* Turn on LED1 */
STM_EVAL_LEDOn(LED1);
/* Enable PWR and BKP clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR | RCC_APB1Periph_BKP, ENABLE);
/* Enable WKUP pin */
PWR_WakeUpPinCmd(ENABLE);
/* Allow access to BKP Domain */
PWR_BackupAccessCmd(ENABLE);
/* Configure RTC clock source and prescaler */
RTC_Configuration();
/* Configure the SysTick to generate an interrupt each 250 ms */
SysTick_Configuration();
while (1)
{
}
}
void Board_main(void)
{
uint8_t i;
uint16_t flash_flag = 0;
uint16_t copy_file_flag = 0;
/* RCC system reset(for debug purpose) */
RCC_DeInit();
/* Enable HSE */
RCC_HSEConfig(RCC_HSE_ON);
/* Wait till HSE is ready */
HSEStartUpStatus = RCC_WaitForHSEStartUp();
if(HSEStartUpStatus == SUCCESS)
{
#if 0
/* Enable Prefetch Buffer */
FLASH_PrefetchBufferCmd(FLASH_PrefetchBuffer_Enable);
FLASH_HalfCycleAccessCmd(FLASH_HalfCycleAccess_Disable);
/* Flash 2 wait state */
FLASH_SetLatency(FLASH_Latency_2);
#else
FLASH_PrefetchBufferCmd(FLASH_PrefetchBuffer_Enable);
FLASH_HalfCycleAccessCmd(FLASH_HalfCycleAccess_Enable);
/* Flash 2 wait state */
/*FLASH_SetLatency(FLASH_Latency_2);*/
FLASH_SetLatency(FLASH_Latency_0); /*abin@ */
#endif
/* HCLK = SYSCLK */
RCC_HCLKConfig(RCC_SYSCLK_Div1);
/* PCLK2 = HCLK */
RCC_PCLK2Config(RCC_HCLK_Div1);
/* PCLK1 = HCLK/2 */
RCC_PCLK1Config(RCC_HCLK_Div2);
#if 0
/* PLLCLK = 8MHz * 9 = 72 MHz */
/*abin:note*/
RCC_PLLConfig(RCC_PLLSource_HSE_Div1, RCC_PLLMul_9);
// RCC_PLLConfig(RCC_PLLSource_HSE_Div1, RCC_PLLMul_8);
/* Enable PLL */
RCC_PLLCmd(ENABLE);
/* Wait till PLL is ready */
while(RCC_GetFlagStatus(RCC_FLAG_PLLRDY) == RESET)
{
}
/* Select PLL as system clock source */
RCC_SYSCLKConfig(RCC_SYSCLKSource_PLLCLK);
/* Wait till PLL is used as system clock source */
while(RCC_GetSYSCLKSource() != 0x08)
{
}
#else
RCC_PLLCmd(DISABLE);
/* Select HSE as system clock source */
RCC_SYSCLKConfig(RCC_SYSCLKSource_HSE);
/* Wait till PLL is used as system clock source */
while(RCC_GetSYSCLKSource() != 0x04)
{
}
#endif
}
/* Enable GPIOA, GPIOB, and AFIO clocks */
RCC_APB2PeriphClockCmd( RCC_APB2Periph_GPIOA |RCC_APB2Periph_GPIOB| RCC_APB2Periph_AFIO, ENABLE);
/* Enable DMA1 ,DMA2 clock */
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1|RCC_AHBPeriph_DMA2, ENABLE);
/* Enable ADC1 ADC2,and GPIOC clock */
RCC_APB2PeriphClockCmd(RCC_APB2Periph_ADC1 |RCC_APB2Periph_ADC2| RCC_APB2Periph_GPIOC, ENABLE);
/* Enable PWR and BKP clock */
RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR | RCC_APB1Periph_BKP, ENABLE);
/* Enable write access to Backup domain */
PWR_BackupAccessCmd(ENABLE);
/* Clear Tamper pin Event(TE) pending flag */
BKP_ClearFlag();
#if ABIN_DEBUG
USART_InitStructure.USART_BaudRate = 115200;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
STM_EVAL_COMInit(COM1, &USART_InitStructure);
/* Output a message on Hyperterminal using printf function */
//sys_printf("\n\r abin 8M is ok moify flash latency :USART Init end \n\r");
#endif
/*------------------- Resources Initialization -----------------------------*/
/* GPIO Configuration */
GPIO_Config();
//sys_printf("\n\r abin mul2 :GPIO_Config \n\r");
#if ABIN_CPU_UPGRADE2HIGHSPEED_OPTION
USB_Plugin_State = GPIO_ReadInputDataBit(GPIOB, GPIO_Pin_14);
if(USB_Plugin_State == 1)
{
//sys_printf("\n\r abin switch to high speed !!\n\r");
UpgradeToHighSpeed();
}
#endif
/* Interrupt Configuration */
InterruptConfig();
/* Configure the systick */
SysTick_Configuration();
/*------------------- Drivers Initialization -------------------------------*/
/* Initialize the Low Power application */
LowPower_Init();
/* Enable WKUP pin */
PWR_WakeUpPinCmd(ENABLE);
/* Allow access to BKP Domain */
PWR_BackupAccessCmd(ENABLE);
RTC_Init();
/* If HSE is not detected at program startup */
if(HSEStartUpStatus == ERROR)
{
/* Generate NMI exception */
SCB->ICSR |= SCB_ICSR_NMIPENDSET;
}
USB_Disconnect_Config();
GPIO_SetBits(USB_DISCONNECT, USB_DISCONNECT_PIN);/*???abin@20100714*/
WakupPin_Init();
//sys_printf("\n\r abin before CheckPowerOnReason\n\r");
CheckPowerOnReason();
//sys_printf("\n\r abin after CheckPowerOnReason\n\r");
Board_ADC_Init();
/*init the flag*/
flash_flag = *(uint16_t *)FLASH_READY_ADDRESS;
if( flash_flag != FLAG_FLASH_READY)
{
//sys_printf("\n\r abin ready to erase flash \n\r");
FLASH_Unlock();
FLASH_ClearFlag(FLASH_FLAG_EOP | FLASH_FLAG_PGERR | FLASH_FLAG_WRPRTERR);
//Erase the 32 page 32K
for(i = 0;i< DATA_PAGES;i++)
{
//sys_printf("\n\r abin ready to erase aa");
FLASH_ErasePage(DATA_LOGGER_ADDRESS_START + i * 1024);/*数据在Page1...page32存放*/
}
FLASH_ErasePage(FLASH_READY_ADDRESS); /*abin@20100715 没添加保护*/
FLASH_ProgramHalfWord(FLASH_READY_ADDRESS , FLAG_FLASH_READY);
FLASH_ErasePage(REOCRD_COUNT_ADDRESS);
FLASH_ProgramHalfWord(REOCRD_COUNT_ADDRESS , 0x0000);
FLASH_Lock();
//sys_printf("\n\r abin mul2 :erase flash end!!!\n\r");
}
//sys_printf("\n\r abin ready to erase flash end \n\r");
USB_Plugin_State = GPIO_ReadInputDataBit(GPIOB, GPIO_Pin_14);
if(USB_Plugin_State == 0)
{
record_count = *(uint16_t *)REOCRD_COUNT_ADDRESS;
if(record_count >= 15428)
{
//Write the full flag
//Do nothing....
while(1)
{
//sys_printf("\n\r sample end !!!!!!!!!!!!!!!!!!!!!\n\r");
Led_One_By_One(4);
/*应该进入standy 模式 abin@20100715*/
}
}
else
{
//sys_printf("\n\r abin ready to add sample count \n\r");
FLASH_Unlock();
FLASH_ClearFlag(FLASH_FLAG_EOP | FLASH_FLAG_PGERR | FLASH_FLAG_WRPRTERR);
FLASH_ProgramHalfWord(DATA_LOGGER_ADDRESS_START + record_count * 2, GetTemperature());
//Erase first
FLASH_ErasePage(REOCRD_COUNT_ADDRESS);
//Update the count
record_count = record_count + 1;
FLASH_ProgramHalfWord(REOCRD_COUNT_ADDRESS , record_count);
FLASH_Lock();
//sys_printf("\n\r abin add sample count :end\n\r");
}
//sys_printf("\n\r %000\n\r");
GPIO_SetBits(GPIOA, GPIO_Pin_1);
#if 0
Delay(25);
#else
Delay(5);
#endif
//sys_printf("\n\r %111\n\r");
}
else
{
Enable_SDcard();
/*
if there is usb connect, copy the data to sdcard. and start the mass storage
*/
copy_file_flag = *(uint16_t *)COPY_FILE_ADDRESS;
if(copy_file_flag == FLAG_FILE_COPYED)
{
Write_Copy_File_Flag(FLAG_FILE_NO_COPYED);
USB_Disconnect_Config();
GPIO_SetBits(USB_DISCONNECT, USB_DISCONNECT_PIN);
Delay(10);
GPIO_ResetBits(USB_DISCONNECT, USB_DISCONNECT_PIN);
/* Enable and GPIOD clock */
Mass_Storage_Start ();
while( bDeviceState != CONFIGURED)
{
Led_Both(1);
}
USB_Plugin_State = GPIO_ReadInputDataBit(GPIOB, GPIO_Pin_14);
while( USB_Plugin_State == 1)/* U-DISK success ,then CPU Loop in here*/
{
USB_Plugin_State = GPIO_ReadInputDataBit(GPIOB, GPIO_Pin_14);
Led_One_By_One(1);
//sys_printf("\n\r abin :mul2 u disk !!!\n\r");
}
PowerOff();
Write_Copy_File_Flag(FLAG_FILE_NO_COPYED);
}
else
{
Write_Copy_File_Flag(FLAG_FILE_COPYED);
Led_Green_Flink(3);
NAND_FAT();
CreateDataLoggerFile();
Write_Copy_File_Flag(FLAG_FILE_COPYED);
//sys_printf("\n\r abin :mul2 NAND_FAT!!!\n\r");
}
//sys_printf("\n\r abin :mul2 Disable_SDcard!!!\n\r");
Disable_SDcard();
BKP_WriteBackupRegister(BKP_POWER_ON, FLAG_POWER_OFF);
PWR_EnterSTANDBYMode();
/* Generate a system reset */
//NVIC_SystemReset();
}
//sys_printf("\n\r @111 \n\r");
/* Set the RTC Alarm after 60s */
RTC_SetAlarm(RTC_GetCounter()+ 3);
//sys_printf("\n\r @222:RTC_GetCounter()=0x%x \n\r",RTC_GetCounter());
/* Wait until last write operation on RTC registers has finished */
RTC_WaitForLastTask();
//sys_printf("\n\r @333\n\r");
PWR_EnterSTANDBYMode();
}
int main(void)
{
RCC_APB1PeriphClockCmd( RCC_APB1Periph_PWR, ENABLE);//!!!!
// тактирование ядра низкоскоростным внутренним генератором 4мгц
RCC->ICSCR &= ~RCC_ICSCR_MSIRANGE;//!!!!
RCC->ICSCR |= RCC_ICSCR_MSIRANGE_6;//!!!!
//RTC_Initilithahion();//!!!!
////////////////////////////////////////////////////////////////////
delay_ms(1000);//!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
curent_cmd = 0;
PCount_Start = 0;
/////////////////// настройка пробуждения
RCC_HSICmd(DISABLE);
PWR_PVDCmd(DISABLE);
PWR_UltraLowPowerCmd(ENABLE);
PWR_WakeUpPinCmd(PWR_WakeUpPin_1,ENABLE);
PWR_UltraLowPowerCmd(ENABLE);
////////////// настройка прирывания для будильника в неспящем режиме
EXTI_InitTypeDef exti;
NVIC_InitTypeDef NVIC_InitStructure;
EXTI_ClearITPendingBit(EXTI_Line17);
exti.EXTI_Line = EXTI_Line17;
exti.EXTI_Mode = EXTI_Mode_Interrupt;
exti.EXTI_Trigger = EXTI_Trigger_Rising;
exti.EXTI_LineCmd = ENABLE;
EXTI_Init(&exti);
NVIC_InitStructure.NVIC_IRQChannel = RTC_Alarm_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
//////////////////
if(PWR_GetFlagStatus(PWR_FLAG_SB)!=RESET)//Если МК вышел из режима standby
{
WkupFlag=1;
curent_cmd = 1;
if(RTC_GetFlagStatus(RTC_FLAG_ALRAF)!=RESET)//Если МК вышел из режима ALARM
{
//RTC_Initilithahion();//!!!!
//PWR_RTCAccessCmd(ENABLE);
//RTC_ClearFlag(RTC_FLAG_ALRAF);
//PWR_RTCAccessCmd(DISABLE);
//f_WakeupToAlarm=1;
curent_cmd = 5;
}
//RCC_APB1PeriphClockCmd(RCC_APB1Periph_PWR,ENABLE);
PWR_ClearFlag(PWR_FLAG_SB); //Сброс флага, который указывает на то, что МК вышел из режима standby
PWR_RTCAccessCmd(ENABLE); // Доступ в RTC
//RTC_ClearITPendingBit(RTC_IT_WUT);
//RTC_ClearFlag(RTC_FLAG_WUTF);
RTC_ClearFlag(RTC_FLAG_ALRAF);
PWR_RTCAccessCmd(DISABLE);
}
else
{
WkupFlag=0;
RTC_TimeTypeDef alarmTime;
alarmTime.RTC_H12 = RTC_H12_PM;//!!!!;
alarmTime.RTC_Hours = 20;
alarmTime.RTC_Minutes = 0;
alarmTime.RTC_Seconds = 20;
RTC_Initilithahion();//!!!!
//RTC_Set_Alarm(alarmTime);/// Магическая последовательность, 1. RTC_Set_Alarm, 2. RTC_Set_Time иначе не работает будильник
RTC_TimeTypeDef RTC_Time;
RTC_DateTypeDef RTC_Date;
RTC_Time.RTC_H12 = RTC_H12_PM;//!!!!;
RTC_Time.RTC_Hours = 20;
RTC_Time.RTC_Minutes = 00;
RTC_Time.RTC_Seconds = 00;
RTC_Date.RTC_WeekDay = RTC_Weekday_Sunday;
RTC_Date.RTC_Year = 14;
RTC_Date.RTC_Month = 8;
RTC_Date.RTC_Date = 17;
RTC_Set_TimeDate(RTC_Time, RTC_Date);///
}
//else curent_cmd = 0;//f_WakeupToAlarm=0;
//RTC_Initilithahion();//!!!!
//RTC_Set_Time();
OLED_Init();
OLED_Clear();
char i,j;
/*
RCC_GetClocksFreq(&Frequency);
f=Frequency.SYSCLK_Frequency/1000;
IntToStr(a,f);
OLED_DrawString_fast(30,30,a,10);
*/
OLED_LcdCache_Clear();
//if(0==WkupFlag) //Если МК до этого не находился в режиме STANDBY!!!!!!!!!!!!!!!!!
//PWR_EnterSTANDBYMode(); //Перейди в режим STANDBY!!!!!!!!!!!!!!!!!!!
//OLED_DrawBitmap_fast(3,12,menu1_sprait,123,40);
//delay_ms(10000);
WaitToSleep = 0;
TACT_Config();
BackTimeAndData.hour=0;
BackTimeAndData.minute=0;
BackTimeAndData.second=0;
globa_menu = 1;
f_aktive_menu = 0;
//curent_cmd = 0;
PWatch_Setup_Step = 0;
key_up = 0;
key_down = 0;
key_ok = 0;
PCount_Start = 0;
while(1)
{
key = 0;
key_ok = GPIO_ReadInputDataBit(GPIOA, GPIO_Pin_0);
key_down = GPIO_ReadInputDataBit(GPIOA, GPIO_Pin_2);
key_up = GPIO_ReadInputDataBit(GPIOB, GPIO_Pin_12);
/*
OLED_DrawString_fast(0,0," ",10);
IntToStr(bbb,key_ok);
OLED_DrawString_fast(0,0,bbb,10);
IntToStr(bbb,key_down);
OLED_DrawString_fast(30,0,bbb,10);
IntToStr(bbb,key_up);
OLED_DrawString_fast(60,0,bbb,10);
*/
if (key_ok!=0)
{
key_ok = 0;
key = 1;
//OLED_DrawString_fast(0,0,"000000000",10);
//f_aktive_menu = 1;
/*
if (f_aktive_menu == 1)
{
//f_work_comand = 1;
f_aktive_menu = 0;
f_clearScrin = 1;
curent_cmd = menu_cmd[globa_menu-1];
}
else curent_cmd = 255 ;
*/
}
if (key_down==0)
{
key_down = 0;
key = 2;
/*
if ((globa_menu>1)&&(f_work_comand == 0)) globa_menu--;
else globa_menu = 1;
//IntToStr(bbb,globa_menu);
//OLED_DrawString_fast(0,0,bbb,10);
*/
}
if (key_up==0)
{
key_up = 0;
key = 12;
/*
if ((globa_menu<4)&&(f_work_comand == 0)) globa_menu++;
else globa_menu = 4;
//IntToStr(bbb,globa_menu);
//OLED_DrawString_fast(0,0,bbb,10);
*/
}
if (key!=0)
{
GPIO_SetBits(GPIOA, GPIO_Pin_1);
delay_ms(30);
GPIO_ResetBits(GPIOA, GPIO_Pin_1);
}
/*
if (f_clearScrin==1)
{
OLED_Clear();
f_clearScrin=0;
}
*/
//if (f_aktive_menu==0)
//{
switch(curent_cmd)
{
case 0: //нет команды
PWatch_Menu();
break;
case 1: //Программа показа часов (главная страница)
//OLED_Clear();
//f_work_comand = 1;
PWatch_Anim();
break;
case 2: //Программа настройки даты/времени и др.
//OLED_Clear();
OLED_DrawString_fast(0,0,"Календарь",10);
curent_cmd = 0;
break;
case 3:
//OLED_Clear();
PWatch_Set_Alarm();
break;
case 4:
//OLED_Clear();
//OLED_DrawString_fast(0,0,"Настройки",10);
//f_work_comand = 1;
PWatch_Setup();
break;
case 5:
PWatch_Vibration();
break;
case 254:
OLED_Clear();
break;
/*case 255:
OLED_Clear();
OLED_DrawBitmap_fast(3,12,menu1_sprait,123,40);
f_aktive_menu = 1;
//f_work_comand = 0;
//key=0;
break;
*/
default: //выполнить, если ни один вариант не подошел
break;
}
//}
//else
//{
//PWatch_Menu();
//}
/*
if(WainToAlarm == 1)
{
OLED_DrawString_fast(0,0,"alarm1",10);
WainToAlarm =0;
}
*/
//if(WaitToSleep>=5)
//{
//WaitToSleep=0;
//PWR_ClearFlag(PWR_FLAG_SB); //Сброс флага, который указывает на то, что МК вышел из режима standby
/*
for (i=255; i>0; i--)
{
OLED_SetContrast(i);
IntToStr(a,i);
OLED_DrawString_fast(0,0,a,10);
//delay_ms(500);
}*/
//OLED_DrawBitmap_fast(32,10,Fallout_Bitmaps,58,60);
//delay_ms(1000);
//OLED_Display_Off();!!!!!!!!!!!!!!!!!!!!!!!!1
//RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA, DISABLE);
//походу стабилитрон кушает 0.1 мА, общее потребление 0.15мА
//PWR_EnterSTANDBYMode();!!!!!!!!!!!!!!!!!!!!!
//}
//WaitToSleep++;
/*
RCC_GetClocksFreq(&Frequency);
f=Frequency.SYSCLK_Frequency/1000;
IntToStr(a,f);
OLED_DrawString_fast(0,0,a,10);
*/
delay_ms(250);
}
}
void shutdown() {
PWR_WakeUpPinCmd(ENABLE); //enable the pin
PWR_EnterSTANDBYMode(); //only wakes on RTC signals or WKUP pin
}
