static int uniphier_emmc_send_cmd(uintptr_t host_base,
				  struct uniphier_mmc_cmd *cmd)
{
	uint32_t mode = 0;
	uint32_t end_bit;
	uint32_t stat, flags, dma_addr;

	mmio_write_32(host_base + SDHCI_INT_STATUS, -1);
	mmio_write_32(host_base + SDHCI_SIGNAL_ENABLE, 0);
	mmio_write_32(host_base + SDHCI_ARGUMENT, cmd->cmdarg);

	if (cmd->is_data)
		mode = SDHCI_TRNS_DMA | SDHCI_TRNS_BLK_CNT_EN |
			SDHCI_TRNS_ACMD12 | SDHCI_TRNS_READ |
			SDHCI_TRNS_MULTI;

	mmio_write_16(host_base + SDHCI_TRANSFER_MODE, mode);

	if (!(cmd->resp_type & MMC_RSP_PRESENT))
		flags = SDHCI_CMD_RESP_NONE;
	else if (cmd->resp_type & MMC_RSP_136)
		flags = SDHCI_CMD_RESP_LONG;
	else if (cmd->resp_type & MMC_RSP_BUSY)
		flags = SDHCI_CMD_RESP_SHORT_BUSY;
	else
		flags = SDHCI_CMD_RESP_SHORT;

	if (cmd->resp_type & MMC_RSP_CRC)
		flags |= SDHCI_CMD_CRC;
	if (cmd->resp_type & MMC_RSP_OPCODE)
		flags |= SDHCI_CMD_INDEX;
	if (cmd->is_data)
		flags |= SDHCI_CMD_DATA;

	if (cmd->resp_type & MMC_RSP_BUSY || cmd->is_data)
		end_bit = SDHCI_INT_DATA_END;
	else
		end_bit = SDHCI_INT_RESPONSE;

	mmio_write_16(host_base + SDHCI_COMMAND,
		      SDHCI_MAKE_CMD(cmd->cmdidx, flags));

	do {
		stat = mmio_read_32(host_base + SDHCI_INT_STATUS);
		if (stat & SDHCI_INT_ERROR)
			return -EIO;

		if (stat & SDHCI_INT_DMA_END) {
			mmio_write_32(host_base + SDHCI_INT_STATUS, stat);
			dma_addr = mmio_read_32(host_base + SDHCI_DMA_ADDRESS);
			mmio_write_32(host_base + SDHCI_DMA_ADDRESS, dma_addr);
		}
	} while (!(stat & end_bit));

	return 0;
}
Esempio n. 2
0
File: sdhci.c Progetto: DFE/u-boot
int sdhci_send_command(struct mmc *mmc, struct mmc_cmd *cmd,
		       struct mmc_data *data)
{
	struct sdhci_host *host = (struct sdhci_host *)mmc->priv;
	unsigned int stat = 0;
	int ret = 0;
	int trans_bytes = 0, is_aligned = 1;
	u32 mask, flags, mode;
	unsigned int timeout, start_addr = 0;
	unsigned int retry = 10000;

	/* Wait max 10 ms */
	timeout = 10;

	sdhci_writel(host, SDHCI_INT_ALL_MASK, SDHCI_INT_STATUS);
	mask = SDHCI_CMD_INHIBIT | SDHCI_DATA_INHIBIT;

	/* We shouldn't wait for data inihibit for stop commands, even
	   though they might use busy signaling */
	if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION)
		mask &= ~SDHCI_DATA_INHIBIT;

	while (sdhci_readl(host, SDHCI_PRESENT_STATE) & mask) {
		if (timeout == 0) {
			printf("Controller never released inhibit bit(s).\n");
			return COMM_ERR;
		}
		timeout--;
		udelay(1000);
	}

	mask = SDHCI_INT_RESPONSE;
	if (!(cmd->resp_type & MMC_RSP_PRESENT))
		flags = SDHCI_CMD_RESP_NONE;
	else if (cmd->resp_type & MMC_RSP_136)
		flags = SDHCI_CMD_RESP_LONG;
	else if (cmd->resp_type & MMC_RSP_BUSY) {
		flags = SDHCI_CMD_RESP_SHORT_BUSY;
		mask |= SDHCI_INT_DATA_END;
	} else
		flags = SDHCI_CMD_RESP_SHORT;

	if (cmd->resp_type & MMC_RSP_CRC)
		flags |= SDHCI_CMD_CRC;
	if (cmd->resp_type & MMC_RSP_OPCODE)
		flags |= SDHCI_CMD_INDEX;
	if (data)
		flags |= SDHCI_CMD_DATA;

	/*Set Transfer mode regarding to data flag*/
	if (data != 0) {
		sdhci_writeb(host, 0xe, SDHCI_TIMEOUT_CONTROL);
		mode = SDHCI_TRNS_BLK_CNT_EN;
		trans_bytes = data->blocks * data->blocksize;
		if (data->blocks > 1)
			mode |= SDHCI_TRNS_MULTI;

		if (data->flags == MMC_DATA_READ)
			mode |= SDHCI_TRNS_READ;

#ifdef CONFIG_MMC_SDMA
		if (data->flags == MMC_DATA_READ)
			start_addr = (unsigned int)data->dest;
		else
			start_addr = (unsigned int)data->src;
		if ((host->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR) &&
				(start_addr & 0x7) != 0x0) {
			is_aligned = 0;
			start_addr = (unsigned int)aligned_buffer;
			if (data->flags != MMC_DATA_READ)
				memcpy(aligned_buffer, data->src, trans_bytes);
		}

		sdhci_writel(host, start_addr, SDHCI_DMA_ADDRESS);
		mode |= SDHCI_TRNS_DMA;
#endif
		sdhci_writew(host, SDHCI_MAKE_BLKSZ(SDHCI_DEFAULT_BOUNDARY_ARG,
				data->blocksize),
				SDHCI_BLOCK_SIZE);
		sdhci_writew(host, data->blocks, SDHCI_BLOCK_COUNT);
		sdhci_writew(host, mode, SDHCI_TRANSFER_MODE);
	}

	sdhci_writel(host, cmd->cmdarg, SDHCI_ARGUMENT);
#ifdef CONFIG_MMC_SDMA
	flush_cache(start_addr, trans_bytes);
#endif
	sdhci_writew(host, SDHCI_MAKE_CMD(cmd->cmdidx, flags), SDHCI_COMMAND);
	do {
		stat = sdhci_readl(host, SDHCI_INT_STATUS);
		if (stat & SDHCI_INT_ERROR)
			break;
		if (--retry == 0)
			break;
	} while ((stat & mask) != mask);

	if (retry == 0) {
		if (host->quirks & SDHCI_QUIRK_BROKEN_R1B)
			return 0;
		else {
			printf("Timeout for status update!\n");
			return TIMEOUT;
		}
	}

	if ((stat & (SDHCI_INT_ERROR | mask)) == mask) {
		sdhci_cmd_done(host, cmd);
		sdhci_writel(host, mask, SDHCI_INT_STATUS);
	} else
		ret = -1;

	if (!ret && data)
		ret = sdhci_transfer_data(host, data, start_addr);

	if (host->quirks & SDHCI_QUIRK_WAIT_SEND_CMD)
		udelay(1000);

	stat = sdhci_readl(host, SDHCI_INT_STATUS);
	sdhci_writel(host, SDHCI_INT_ALL_MASK, SDHCI_INT_STATUS);
	if (!ret) {
		if ((host->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR) &&
				!is_aligned && (data->flags == MMC_DATA_READ))
			memcpy(data->dest, aligned_buffer, trans_bytes);
		return 0;
	}

	sdhci_reset(host, SDHCI_RESET_CMD);
	sdhci_reset(host, SDHCI_RESET_DATA);
	if (stat & SDHCI_INT_TIMEOUT)
		return TIMEOUT;
	else
		return COMM_ERR;
}
Esempio n. 3
0
static int sdhci_send_command(struct udevice *dev, struct mmc_cmd *cmd,
			      struct mmc_data *data)
{
	struct mmc *mmc = mmc_get_mmc_dev(dev);

#else
static int sdhci_send_command(struct mmc *mmc, struct mmc_cmd *cmd,
			      struct mmc_data *data)
{
#endif
	struct sdhci_host *host = mmc->priv;
	unsigned int stat = 0;
	int ret = 0;
	int trans_bytes = 0, is_aligned = 1;
	u32 mask, flags, mode;
	unsigned int time = 0, start_addr = 0;
	int mmc_dev = mmc_get_blk_desc(mmc)->devnum;
	ulong start = get_timer(0);

	/* Timeout unit - ms */
	static unsigned int cmd_timeout = SDHCI_CMD_DEFAULT_TIMEOUT;

	mask = SDHCI_CMD_INHIBIT | SDHCI_DATA_INHIBIT;

	/* We shouldn't wait for data inihibit for stop commands, even
	   though they might use busy signaling */
	if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION ||
	    ((cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK ||
	      cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK_HS200) && !data))
		mask &= ~SDHCI_DATA_INHIBIT;

	while (sdhci_readl(host, SDHCI_PRESENT_STATE) & mask) {
		if (time >= cmd_timeout) {
			printf("%s: MMC: %d busy ", __func__, mmc_dev);
			if (2 * cmd_timeout <= SDHCI_CMD_MAX_TIMEOUT) {
				cmd_timeout += cmd_timeout;
				printf("timeout increasing to: %u ms.\n",
				       cmd_timeout);
			} else {
				puts("timeout.\n");
				return -ECOMM;
			}
		}
		time++;
		udelay(1000);
	}

	sdhci_writel(host, SDHCI_INT_ALL_MASK, SDHCI_INT_STATUS);

	mask = SDHCI_INT_RESPONSE;
	if ((cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK ||
	     cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK_HS200) && !data)
		mask = SDHCI_INT_DATA_AVAIL;

	if (!(cmd->resp_type & MMC_RSP_PRESENT))
		flags = SDHCI_CMD_RESP_NONE;
	else if (cmd->resp_type & MMC_RSP_136)
		flags = SDHCI_CMD_RESP_LONG;
	else if (cmd->resp_type & MMC_RSP_BUSY) {
		flags = SDHCI_CMD_RESP_SHORT_BUSY;
		if (data)
			mask |= SDHCI_INT_DATA_END;
	} else
		flags = SDHCI_CMD_RESP_SHORT;

	if (cmd->resp_type & MMC_RSP_CRC)
		flags |= SDHCI_CMD_CRC;
	if (cmd->resp_type & MMC_RSP_OPCODE)
		flags |= SDHCI_CMD_INDEX;
	if (data || cmd->cmdidx ==  MMC_CMD_SEND_TUNING_BLOCK ||
	    cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK_HS200)
		flags |= SDHCI_CMD_DATA;

	/* Set Transfer mode regarding to data flag */
	if (data) {
		sdhci_writeb(host, 0xe, SDHCI_TIMEOUT_CONTROL);
		mode = SDHCI_TRNS_BLK_CNT_EN;
		trans_bytes = data->blocks * data->blocksize;
		if (data->blocks > 1)
			mode |= SDHCI_TRNS_MULTI;

		if (data->flags == MMC_DATA_READ)
			mode |= SDHCI_TRNS_READ;

#ifdef CONFIG_MMC_SDHCI_SDMA
		if (data->flags == MMC_DATA_READ)
			start_addr = (unsigned long)data->dest;
		else
			start_addr = (unsigned long)data->src;
		if ((host->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR) &&
				(start_addr & 0x7) != 0x0) {
			is_aligned = 0;
			start_addr = (unsigned long)aligned_buffer;
			if (data->flags != MMC_DATA_READ)
				memcpy(aligned_buffer, data->src, trans_bytes);
		}

#if defined(CONFIG_FIXED_SDHCI_ALIGNED_BUFFER)
		/*
		 * Always use this bounce-buffer when
		 * CONFIG_FIXED_SDHCI_ALIGNED_BUFFER is defined
		 */
		is_aligned = 0;
		start_addr = (unsigned long)aligned_buffer;
		if (data->flags != MMC_DATA_READ)
			memcpy(aligned_buffer, data->src, trans_bytes);
#endif

		sdhci_writel(host, start_addr, SDHCI_DMA_ADDRESS);
		mode |= SDHCI_TRNS_DMA;
#endif
		sdhci_writew(host, SDHCI_MAKE_BLKSZ(SDHCI_DEFAULT_BOUNDARY_ARG,
				data->blocksize),
				SDHCI_BLOCK_SIZE);
		sdhci_writew(host, data->blocks, SDHCI_BLOCK_COUNT);
		sdhci_writew(host, mode, SDHCI_TRANSFER_MODE);
	} else if (cmd->resp_type & MMC_RSP_BUSY) {
		sdhci_writeb(host, 0xe, SDHCI_TIMEOUT_CONTROL);
	}

	sdhci_writel(host, cmd->cmdarg, SDHCI_ARGUMENT);
#ifdef CONFIG_MMC_SDHCI_SDMA
	if (data) {
		trans_bytes = ALIGN(trans_bytes, CONFIG_SYS_CACHELINE_SIZE);
		flush_cache(start_addr, trans_bytes);
	}
#endif
	sdhci_writew(host, SDHCI_MAKE_CMD(cmd->cmdidx, flags), SDHCI_COMMAND);
	start = get_timer(0);
	do {
		stat = sdhci_readl(host, SDHCI_INT_STATUS);
		if (stat & SDHCI_INT_ERROR)
			break;

		if (get_timer(start) >= SDHCI_READ_STATUS_TIMEOUT) {
			if (host->quirks & SDHCI_QUIRK_BROKEN_R1B) {
				return 0;
			} else {
				printf("%s: Timeout for status update!\n",
				       __func__);
				return -ETIMEDOUT;
			}
		}
	} while ((stat & mask) != mask);

	if ((stat & (SDHCI_INT_ERROR | mask)) == mask) {
		sdhci_cmd_done(host, cmd);
		sdhci_writel(host, mask, SDHCI_INT_STATUS);
	} else
		ret = -1;

	if (!ret && data)
		ret = sdhci_transfer_data(host, data, start_addr);

	if (host->quirks & SDHCI_QUIRK_WAIT_SEND_CMD)
		udelay(1000);

	stat = sdhci_readl(host, SDHCI_INT_STATUS);
	sdhci_writel(host, SDHCI_INT_ALL_MASK, SDHCI_INT_STATUS);
	if (!ret) {
		if ((host->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR) &&
				!is_aligned && (data->flags == MMC_DATA_READ))
			memcpy(data->dest, aligned_buffer, trans_bytes);
		return 0;
	}

	sdhci_reset(host, SDHCI_RESET_CMD);
	sdhci_reset(host, SDHCI_RESET_DATA);
	if (stat & SDHCI_INT_TIMEOUT)
		return -ETIMEDOUT;
	else
		return -ECOMM;
}

#if defined(CONFIG_DM_MMC) && defined(MMC_SUPPORTS_TUNING)
static int sdhci_execute_tuning(struct udevice *dev, uint opcode)
{
	int err;
	struct mmc *mmc = mmc_get_mmc_dev(dev);
	struct sdhci_host *host = mmc->priv;

	debug("%s\n", __func__);

	if (host->ops && host->ops->platform_execute_tuning) {
		err = host->ops->platform_execute_tuning(mmc, opcode);
		if (err)
			return err;
		return 0;
	}
	return 0;
}
Esempio n. 4
0
/*
 * Sends a command out on the bus.  Takes the mmc pointer,
 * a command pointer, and an optional data pointer.
 */
static int
s3c_hsmmc_send_command(struct mmc *mmc, struct mmc_cmd *cmd,
			struct mmc_data *data)
{
	struct sdhci_host *host = mmc->priv;

	int flags, i;
	u32 mask;
	unsigned long timeout;

	/* Wait max 10 ms */
	timeout = 10;

	mask = SDHCI_CMD_INHIBIT;
	if ((data != NULL) || (cmd->flags & MMC_RSP_BUSY))
		mask |= SDHCI_DATA_INHIBIT;

	/* We shouldn't wait for data inihibit for stop commands, even
	   though they might use busy signaling */
	if (data)
		mask &= ~SDHCI_DATA_INHIBIT;

	while (readl(host->ioaddr + SDHCI_PRESENT_STATE) & mask) {
		if (timeout == 0) {
			printk("Controller never released " \
				"inhibit bit(s).\n");
			return -1;
		}
		timeout--;
		mdelay(1);
	}

	if (data)
		sdhci_prepare_data(host, data);

	dbg("cmd->arg: %08x\n", cmd->arg);	
	writel(cmd->arg, host->ioaddr + SDHCI_ARGUMENT);

	if (data)
		sdhci_set_transfer_mode(host, data);

	if ((cmd->resp_type & MMC_RSP_136) && (cmd->resp_type & MMC_RSP_BUSY)) {
		return -1;
	}

	if (!(cmd->resp_type & MMC_RSP_PRESENT))
		flags = SDHCI_CMD_RESP_NONE;
	else if (cmd->resp_type & MMC_RSP_136)
		flags = SDHCI_CMD_RESP_LONG;
	else if (cmd->resp_type & MMC_RSP_BUSY)
		flags = SDHCI_CMD_RESP_SHORT_BUSY;
	else
		flags = SDHCI_CMD_RESP_SHORT;

	if (cmd->resp_type & MMC_RSP_CRC)
		flags |= SDHCI_CMD_CRC;
	if (cmd->resp_type & MMC_RSP_OPCODE)
		flags |= SDHCI_CMD_INDEX;
	if (data)
		flags |= SDHCI_CMD_DATA;

	dbg("cmd: %d\n", cmd->opcode);
	
	writew(SDHCI_MAKE_CMD(cmd->opcode, flags),
		host->ioaddr + SDHCI_COMMAND);

	for (i=0; i<0x100000; i++) {
		mask = readl(host->ioaddr + SDHCI_INT_STATUS);
		if (mask & SDHCI_INT_RESPONSE) {
			if (!data)
				writel(mask, host->ioaddr + SDHCI_INT_STATUS);
			break;
		}
	}
	
	if (0x100000 == i) {
		printk("FAIL: waiting for status update.\n");
		return TIMEOUT;
	}

	if (mask & SDHCI_INT_TIMEOUT) {
		dbg("timeout: %08x cmd %d\n", mask, cmd->opcode);
		return TIMEOUT;
	}
	else if (mask & SDHCI_INT_ERROR) {
		dbg("error: %08x cmd %d\n", mask, cmd->opcode);
		return -1;
	}
	
	if (cmd->resp_type & MMC_RSP_PRESENT) {
		if (cmd->resp_type & MMC_RSP_136) {
			/* CRC is stripped so we need to do some shifting. */
			for (i = 0;i < 4;i++) {
				cmd->resp[i] = readl(host->ioaddr +
					SDHCI_RESPONSE + (3-i)*4) << 8;
				dbg("cmd->resp[%d]: %08x\n", i, cmd->resp[i]);
				if (i != 3)
					cmd->resp[i] |=
						readb(host->ioaddr +
						SDHCI_RESPONSE + (3-i)*4-1);
				dbg("cmd->resp[%d]: %08x\n", i, cmd->resp[i]);				
			}
		} else if (cmd->resp_type & MMC_RSP_BUSY) {
			for (i = 0;i < 0x100000; i++)
				if (readl(host->ioaddr + SDHCI_PRESENT_STATE) & SDHCI_DATA_BIT(0))
					break;
			if (0x100000 == i) {
				printk("FAIL: card is still busy\n");
				return TIMEOUT;
			}
							
			cmd->resp[0] = readl(host->ioaddr + SDHCI_RESPONSE);
			dbg("cmd->resp[0]: %08x\n", cmd->resp[i]);
		} else {
			cmd->resp[0] = readl(host->ioaddr + SDHCI_RESPONSE);
			dbg("cmd->resp[0]: %08x\n", cmd->resp[i]);
		}
	}

	if (data) {
		while (!(mask & (SDHCI_INT_DATA_END | SDHCI_INT_ERROR | SDHCI_INT_DMA_END))) {
			mask = readl(host->ioaddr + SDHCI_INT_STATUS);
		}
		writel(mask, host->ioaddr + SDHCI_INT_STATUS);
		if (mask & SDHCI_INT_ERROR) {
			printf("error during transfer: 0x%08x\n", mask);
			return -1;
		} else if (mask & SDHCI_INT_DMA_END) {
			printf("SDHCI_INT_DMA_END\n");
		} else {		
			dbg("r/w is done\n");
		}
	}

	mdelay(1);
	return 0;
}
Esempio n. 5
0
static int sdhci_send_command(struct udevice *dev, struct mmc_cmd *cmd,
			      struct mmc_data *data)
{
	struct mmc *mmc = mmc_get_mmc_dev(dev);

#else
static int sdhci_send_command(struct mmc *mmc, struct mmc_cmd *cmd,
			      struct mmc_data *data)
{
#endif
	struct sdhci_host *host = mmc->priv;
	unsigned int stat = 0;
	int ret = 0;
	int trans_bytes = 0, is_aligned = 1;
	u32 mask, flags, mode;
	unsigned int time = 0, start_addr = 0;
	int mmc_dev = mmc_get_blk_desc(mmc)->devnum;
	unsigned start = get_timer(0);

	/* Timeout unit - ms */
	static unsigned int cmd_timeout = SDHCI_CMD_DEFAULT_TIMEOUT;

	sdhci_writel(host, SDHCI_INT_ALL_MASK, SDHCI_INT_STATUS);
	mask = SDHCI_CMD_INHIBIT | SDHCI_DATA_INHIBIT;

	/* We shouldn't wait for data inihibit for stop commands, even
	   though they might use busy signaling */
	if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION)
		mask &= ~SDHCI_DATA_INHIBIT;

	while (sdhci_readl(host, SDHCI_PRESENT_STATE) & mask) {
		if (time >= cmd_timeout) {
			printf("%s: MMC: %d busy ", __func__, mmc_dev);
			if (2 * cmd_timeout <= SDHCI_CMD_MAX_TIMEOUT) {
				cmd_timeout += cmd_timeout;
				printf("timeout increasing to: %u ms.\n",
				       cmd_timeout);
			} else {
				puts("timeout.\n");
				return -ECOMM;
			}
		}
		time++;
		udelay(1000);
	}

	mask = SDHCI_INT_RESPONSE;
	if (!(cmd->resp_type & MMC_RSP_PRESENT))
		flags = SDHCI_CMD_RESP_NONE;
	else if (cmd->resp_type & MMC_RSP_136)
		flags = SDHCI_CMD_RESP_LONG;
	else if (cmd->resp_type & MMC_RSP_BUSY) {
		flags = SDHCI_CMD_RESP_SHORT_BUSY;
		if (data)
			mask |= SDHCI_INT_DATA_END;
	} else
		flags = SDHCI_CMD_RESP_SHORT;

	if (cmd->resp_type & MMC_RSP_CRC)
		flags |= SDHCI_CMD_CRC;
	if (cmd->resp_type & MMC_RSP_OPCODE)
		flags |= SDHCI_CMD_INDEX;
	if (data)
		flags |= SDHCI_CMD_DATA;

	/* Set Transfer mode regarding to data flag */
	if (data != 0) {
		sdhci_writeb(host, 0xe, SDHCI_TIMEOUT_CONTROL);
		mode = SDHCI_TRNS_BLK_CNT_EN;
		trans_bytes = data->blocks * data->blocksize;
		if (data->blocks > 1)
			mode |= SDHCI_TRNS_MULTI;

		if (data->flags == MMC_DATA_READ)
			mode |= SDHCI_TRNS_READ;

#ifdef CONFIG_MMC_SDHCI_SDMA
		if (data->flags == MMC_DATA_READ)
			start_addr = (unsigned long)data->dest;
		else
			start_addr = (unsigned long)data->src;
		if ((host->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR) &&
				(start_addr & 0x7) != 0x0) {
			is_aligned = 0;
			start_addr = (unsigned long)aligned_buffer;
			if (data->flags != MMC_DATA_READ)
				memcpy(aligned_buffer, data->src, trans_bytes);
		}

#if defined(CONFIG_FIXED_SDHCI_ALIGNED_BUFFER)
		/*
		 * Always use this bounce-buffer when
		 * CONFIG_FIXED_SDHCI_ALIGNED_BUFFER is defined
		 */
		is_aligned = 0;
		start_addr = (unsigned long)aligned_buffer;
		if (data->flags != MMC_DATA_READ)
			memcpy(aligned_buffer, data->src, trans_bytes);
#endif

		sdhci_writel(host, start_addr, SDHCI_DMA_ADDRESS);
		mode |= SDHCI_TRNS_DMA;
#endif
		sdhci_writew(host, SDHCI_MAKE_BLKSZ(SDHCI_DEFAULT_BOUNDARY_ARG,
				data->blocksize),
				SDHCI_BLOCK_SIZE);
		sdhci_writew(host, data->blocks, SDHCI_BLOCK_COUNT);
		sdhci_writew(host, mode, SDHCI_TRANSFER_MODE);
	} else if (cmd->resp_type & MMC_RSP_BUSY) {
		sdhci_writeb(host, 0xe, SDHCI_TIMEOUT_CONTROL);
	}

	sdhci_writel(host, cmd->cmdarg, SDHCI_ARGUMENT);
#ifdef CONFIG_MMC_SDHCI_SDMA
	trans_bytes = ALIGN(trans_bytes, CONFIG_SYS_CACHELINE_SIZE);
	flush_cache(start_addr, trans_bytes);
#endif
	sdhci_writew(host, SDHCI_MAKE_CMD(cmd->cmdidx, flags), SDHCI_COMMAND);
	start = get_timer(0);
	do {
		stat = sdhci_readl(host, SDHCI_INT_STATUS);
		if (stat & SDHCI_INT_ERROR)
			break;

		if (get_timer(start) >= SDHCI_READ_STATUS_TIMEOUT) {
			if (host->quirks & SDHCI_QUIRK_BROKEN_R1B) {
				return 0;
			} else {
				printf("%s: Timeout for status update!\n",
				       __func__);
				return -ETIMEDOUT;
			}
		}
	} while ((stat & mask) != mask);

	if ((stat & (SDHCI_INT_ERROR | mask)) == mask) {
		sdhci_cmd_done(host, cmd);
		sdhci_writel(host, mask, SDHCI_INT_STATUS);
	} else
		ret = -1;

	if (!ret && data)
		ret = sdhci_transfer_data(host, data, start_addr);

	if (host->quirks & SDHCI_QUIRK_WAIT_SEND_CMD)
		udelay(1000);

	stat = sdhci_readl(host, SDHCI_INT_STATUS);
	sdhci_writel(host, SDHCI_INT_ALL_MASK, SDHCI_INT_STATUS);
	if (!ret) {
		if ((host->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR) &&
				!is_aligned && (data->flags == MMC_DATA_READ))
			memcpy(data->dest, aligned_buffer, trans_bytes);
		return 0;
	}

	sdhci_reset(host, SDHCI_RESET_CMD);
	sdhci_reset(host, SDHCI_RESET_DATA);
	if (stat & SDHCI_INT_TIMEOUT)
		return -ETIMEDOUT;
	else
		return -ECOMM;
}

static int sdhci_set_clock(struct mmc *mmc, unsigned int clock)
{
	struct sdhci_host *host = mmc->priv;
	unsigned int div, clk = 0, timeout, reg;

	/* Wait max 20 ms */
	timeout = 200;
	while (sdhci_readl(host, SDHCI_PRESENT_STATE) &
			   (SDHCI_CMD_INHIBIT | SDHCI_DATA_INHIBIT)) {
		if (timeout == 0) {
			printf("%s: Timeout to wait cmd & data inhibit\n",
			       __func__);
			return -EBUSY;
		}

		timeout--;
		udelay(100);
	}

	reg = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
	reg &= ~(SDHCI_CLOCK_CARD_EN | SDHCI_CLOCK_INT_EN);
	sdhci_writew(host, reg, SDHCI_CLOCK_CONTROL);

	if (clock == 0)
		return 0;

	if (SDHCI_GET_VERSION(host) >= SDHCI_SPEC_300) {
		/*
		 * Check if the Host Controller supports Programmable Clock
		 * Mode.
		 */
		if (host->clk_mul) {
			for (div = 1; div <= 1024; div++) {
				if ((mmc->cfg->f_max * host->clk_mul / div)
					<= clock)
					break;
			}

			/*
			 * Set Programmable Clock Mode in the Clock
			 * Control register.
			 */
			clk = SDHCI_PROG_CLOCK_MODE;
			div--;
		} else {
			/* Version 3.00 divisors must be a multiple of 2. */
			if (mmc->cfg->f_max <= clock) {
				div = 1;
			} else {
				for (div = 2;
				     div < SDHCI_MAX_DIV_SPEC_300;
				     div += 2) {
					if ((mmc->cfg->f_max / div) <= clock)
						break;
				}
			}
			div >>= 1;
		}
	} else {
		/* Version 2.00 divisors must be a power of 2. */
		for (div = 1; div < SDHCI_MAX_DIV_SPEC_200; div *= 2) {
			if ((mmc->cfg->f_max / div) <= clock)
				break;
		}
		div >>= 1;
	}

	if (host->ops && host->ops->set_clock)
		host->ops->set_clock(host, div);

	clk |= (div & SDHCI_DIV_MASK) << SDHCI_DIVIDER_SHIFT;
	clk |= ((div & SDHCI_DIV_HI_MASK) >> SDHCI_DIV_MASK_LEN)
		<< SDHCI_DIVIDER_HI_SHIFT;
	clk |= SDHCI_CLOCK_INT_EN;
	sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);

	/* Wait max 20 ms */
	timeout = 20;
	while (!((clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL))
		& SDHCI_CLOCK_INT_STABLE)) {
		if (timeout == 0) {
			printf("%s: Internal clock never stabilised.\n",
			       __func__);
			return -EBUSY;
		}
		timeout--;
		udelay(1000);
	}

	clk |= SDHCI_CLOCK_CARD_EN;
	sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
	return 0;
}
Esempio n. 6
0
int sdhci_send_command(struct mmc_host *mmc,
			struct mmc_cmd *cmd, 
			struct mmc_data *data)
{
	bool present;
	u32 mask, flags, mode;
	int ret = 0, trans_bytes = 0, is_aligned = 1;
	u32 timeout, retry = 10000, stat = 0, start_addr = 0;
	struct sdhci_host *host = mmc_priv(mmc);

	/* If polling, assume that the card is always present. */
	if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION) {
		present = TRUE;
	} else {
		present = sdhci_readl(host, SDHCI_PRESENT_STATE) &
				SDHCI_CARD_PRESENT;
	}

	/* If card not present then return error */
	if (!present) {
		return VMM_EIO;
	}

	/* Wait max 10 ms */
	timeout = 10;

	sdhci_writel(host, SDHCI_INT_ALL_MASK, SDHCI_INT_STATUS);
	mask = SDHCI_CMD_INHIBIT | SDHCI_DATA_INHIBIT;

	/* We shouldn't wait for data inihibit for stop commands, even
	   though they might use busy signaling */
	if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION) {
		mask &= ~SDHCI_DATA_INHIBIT;
	}

	while (sdhci_readl(host, SDHCI_PRESENT_STATE) & mask) {
		if (timeout == 0) {
			vmm_printf("%s: Controller never released "
				   "inhibit bit(s).\n", __func__);
			return VMM_EIO;
		}
		timeout--;
		vmm_udelay(1000);
	}

	mask = SDHCI_INT_RESPONSE;
	if (!(cmd->resp_type & MMC_RSP_PRESENT)) {
		flags = SDHCI_CMD_RESP_NONE;
	} else if (cmd->resp_type & MMC_RSP_136) {
		flags = SDHCI_CMD_RESP_LONG;
	} else if (cmd->resp_type & MMC_RSP_BUSY) {
		flags = SDHCI_CMD_RESP_SHORT_BUSY;
		mask |= SDHCI_INT_DATA_END;
	} else {
		flags = SDHCI_CMD_RESP_SHORT;
	}

	if (cmd->resp_type & MMC_RSP_CRC) {
		flags |= SDHCI_CMD_CRC;
	}
	if (cmd->resp_type & MMC_RSP_OPCODE) {
		flags |= SDHCI_CMD_INDEX;
	}
	if (data) {
		flags |= SDHCI_CMD_DATA;
	}

	/* Set Transfer mode regarding to data flag */
	if (data != 0) {
		sdhci_writeb(host, 0xe, SDHCI_TIMEOUT_CONTROL);
		mode = SDHCI_TRNS_BLK_CNT_EN;
		trans_bytes = data->blocks * data->blocksize;
		if (data->blocks > 1) {
			mode |= SDHCI_TRNS_MULTI;
		}

		if (data->flags == MMC_DATA_READ) {
			mode |= SDHCI_TRNS_READ;
		}

		if (host->sdhci_caps & SDHCI_CAN_DO_SDMA) {
			if (data->flags == MMC_DATA_READ) {
				start_addr = (u32)data->dest;
			} else {
				start_addr = (u32)data->src;
			}

			if ((host->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR) &&
			    (start_addr & 0x7) != 0x0) {
				is_aligned = 0;
				start_addr = (u32)host->aligned_buffer;
				if (data->flags != MMC_DATA_READ) {
					memcpy(host->aligned_buffer, 
						data->src, trans_bytes);
				}
			}

			sdhci_writel(host, start_addr, SDHCI_DMA_ADDRESS);
			mode |= SDHCI_TRNS_DMA;

			vmm_flush_cache_range(start_addr, 
						start_addr + trans_bytes);
		}

		sdhci_writew(host, SDHCI_MAKE_BLKSZ(SDHCI_DEFAULT_BOUNDARY_ARG,
				data->blocksize),
				SDHCI_BLOCK_SIZE);
		sdhci_writew(host, data->blocks, SDHCI_BLOCK_COUNT);
		sdhci_writew(host, mode, SDHCI_TRANSFER_MODE);
	}

	sdhci_writel(host, cmd->cmdarg, SDHCI_ARGUMENT);

	sdhci_writew(host, SDHCI_MAKE_CMD(cmd->cmdidx, flags), SDHCI_COMMAND);
	do {
		stat = sdhci_readl(host, SDHCI_INT_STATUS);
		if (stat & SDHCI_INT_ERROR) {
			break;
		}
		if (--retry == 0) {
			break;
		}
	} while ((stat & mask) != mask);

	if (retry == 0) {
		if (host->quirks & SDHCI_QUIRK_BROKEN_R1B)
			return VMM_OK;
		else {
			vmm_printf("%s: Status update timeout!\n", __func__);
			return VMM_ETIMEDOUT;
		}
	}

	if ((stat & (SDHCI_INT_ERROR | mask)) == mask) {
		sdhci_cmd_done(host, cmd);
		sdhci_writel(host, mask, SDHCI_INT_STATUS);
	} else {
		ret = VMM_EFAIL;
	}

	if (!ret && data) {
		ret = sdhci_transfer_data(host, data, start_addr);
	}

	if (host->quirks & SDHCI_QUIRK_WAIT_SEND_CMD) {
		vmm_udelay(1000);
	}

	stat = sdhci_readl(host, SDHCI_INT_STATUS);
	sdhci_writel(host, SDHCI_INT_ALL_MASK, SDHCI_INT_STATUS);
	if (!ret) {
		if ((host->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR) &&
		     !is_aligned && (data->flags == MMC_DATA_READ)) {
			memcpy(data->dest, host->aligned_buffer, trans_bytes);
		}
		return VMM_OK;
	}

	sdhci_reset(host, SDHCI_RESET_CMD);
	sdhci_reset(host, SDHCI_RESET_DATA);

	if (stat & SDHCI_INT_TIMEOUT) {
		return VMM_ETIMEDOUT;
	} else {
		return VMM_EIO;
	}
}
Esempio n. 7
0
int sdhci_send_command_backstage(struct mmc *mmc, struct mmc_cmd *cmd,
		       struct mmc_data *data)
{
	struct sdhci_host *host = (struct sdhci_host *)mmc->priv;
	unsigned int stat = 0;
	int ret = 0;
	int trans_bytes = 0, is_aligned = 1;
	u32 mask, flags, mode;
	unsigned int time = 0, start_addr = 0;
	unsigned int retry = 8000000;
	int mmc_dev = mmc->block_dev.dev;

	/* Timeout unit - ms */
	static unsigned int cmd_timeout = CONFIG_SDHCI_CMD_DEFAULT_TIMEOUT;

	sdhci_writel(host, SDHCI_INT_ALL_MASK, SDHCI_INT_STATUS);
	mask = SDHCI_CMD_INHIBIT | SDHCI_DATA_INHIBIT;

	/* We shouldn't wait for data inihibit for stop commands, even
	   though they might use busy signaling */
	if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION)
		mask &= ~SDHCI_DATA_INHIBIT;

	while (sdhci_readl(host, SDHCI_PRESENT_STATE) & mask) {
		if (time >= cmd_timeout) {
			debugf("%s: MMC: %d busy ", __func__, mmc_dev);
			if (2 * cmd_timeout <= CONFIG_SDHCI_CMD_MAX_TIMEOUT) {
				cmd_timeout += cmd_timeout;
				debugf("timeout increasing to: %u ms.\n",
				       cmd_timeout);
				sdio_dump(host->ioaddr);
			} else {
				errorf("timeout.\n");
				sdio_dump(host->ioaddr);
				return COMM_ERR;
			}
		}
		time++;
		udelay(10000);
	}

	mask = SDHCI_INT_RESPONSE;
	if (!(cmd->resp_type & MMC_RSP_PRESENT))
		flags = SDHCI_CMD_RESP_NONE;
	else if (cmd->resp_type & MMC_RSP_136)
		flags = SDHCI_CMD_RESP_LONG;
	else if (cmd->resp_type & MMC_RSP_BUSY) {
		flags = SDHCI_CMD_RESP_SHORT_BUSY;
		mask |= SDHCI_INT_DATA_END;
	} else
		flags = SDHCI_CMD_RESP_SHORT;

	if (cmd->resp_type & MMC_RSP_CRC)
		flags |= SDHCI_CMD_CRC;
	if (cmd->resp_type & MMC_RSP_OPCODE)
		flags |= SDHCI_CMD_INDEX;
	if (data)
		flags |= SDHCI_CMD_DATA;

	/* Set Transfer mode regarding to data flag */
	if (data != 0) {
		sdhci_writeb(host, 0xe, SDHCI_TIMEOUT_CONTROL);
		mode = SDHCI_TRNS_BLK_CNT_EN;
		trans_bytes = data->blocks * data->blocksize;
		if (data->blocks > 1)
			mode |= SDHCI_TRNS_MULTI;

		if (data->flags == MMC_DATA_READ)
			mode |= SDHCI_TRNS_READ;

#ifdef CONFIG_MMC_SDMA
		if (data->flags == MMC_DATA_READ)
			start_addr = (unsigned int)data->dest;
		else
			start_addr = (unsigned int)data->src;
		if ((host->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR) &&
				(start_addr & 0x7) != 0x0) {
			is_aligned = 0;
			start_addr = (unsigned int)aligned_buffer;
			if (data->flags != MMC_DATA_READ)
				memcpy(aligned_buffer, data->src, trans_bytes);
		}

		sdhci_writel(host, start_addr, SDHCI_DMA_ADDRESS);
		mode |= SDHCI_TRNS_DMA;
#endif
		sdhci_writew(host, SDHCI_MAKE_BLKSZ(SDHCI_DEFAULT_BOUNDARY_ARG,
				data->blocksize),
				SDHCI_BLOCK_SIZE);
		sdhci_writew(host, data->blocks, SDHCI_BLOCK_COUNT);
		sdhci_writew(host, mode, SDHCI_TRANSFER_MODE);
	}

	sdhci_writel(host, cmd->cmdarg, SDHCI_ARGUMENT);
#ifdef CONFIG_MMC_SDMA
	flush_cache(start_addr, trans_bytes);
#endif
	sdhci_writew(host, SDHCI_MAKE_CMD(cmd->cmdidx, flags), SDHCI_COMMAND);
	do {
		stat = sdhci_readl(host, SDHCI_INT_STATUS);
		if (stat & SDHCI_INT_ERROR)
			break;
		if (--retry == 0)
			break;
	} while ((stat & mask) != mask);

	if (retry == 0) {
		if (host->quirks & SDHCI_QUIRK_BROKEN_R1B)
			return 0;
		else {
			errorf("%s: Timeout for status update!\n", __func__);
			sdio_dump(host->ioaddr);
			return TIMEOUT;
		}
	}

	if ((stat & (SDHCI_INT_ERROR | mask)) == mask) {
		sdhci_cmd_done(host, cmd);
		sdhci_writel(host, mask, SDHCI_INT_STATUS);
		/*do not wait for transfer complete*/
		return 0;
	}

	if (host->quirks & SDHCI_QUIRK_WAIT_SEND_CMD)
		udelay(800000);

	stat = sdhci_readl(host, SDHCI_INT_STATUS);
	sdhci_writel(host, SDHCI_INT_ALL_MASK, SDHCI_INT_STATUS);

	if (stat & SDHCI_INT_TIMEOUT){
		//sdio_dump(host->ioaddr);
		sdhci_reset(host, SDHCI_RESET_CMD);
		sdhci_reset(host, SDHCI_RESET_DATA);
		return TIMEOUT;
	}
	else{
		//sdio_dump(host->ioaddr);
		sdhci_reset(host, SDHCI_RESET_CMD);
		sdhci_reset(host, SDHCI_RESET_DATA);
		return COMM_ERR;
	}
}